Cycoloy* Resin C2950HF

Americas: COMMERCIAL
Non-chlorinated and non-brominated flame retardant PC/ABS offering balanced impact and heat properties plus improved flow for various applications.

TYPICAL PROPERTIES ¹ TYPICAL VALUE UNIT STANDARD

MECHANICAL
Tensile Stress, yld, Type I, 50 mm/min 64 MPa ASTM D 638
Tensile Strain, yld, Type I, 50 mm/min 5 % ASTM D 638
Tensile Strain, brk, Type I, 50 mm/min 40 % ASTM D 638
Flexural Stress, yld, 2.6 mm/min, 100 mm span 96 MPa ASTM D 790
Flexural Modulus, 2.6 mm/min, 100 mm span 2580 MPa ASTM D 790
Hardness, Rockwell R 121 - ASTM D 785
IMPACT
Izod Impact, notched, 23°C 453 J/m ASTM D 256
Instrumented Impact Energy @ peak, 23°C 54 J ASTM D 3763
THERMAL
Vicat Softening Temp, Rate B/50 112 °C ASTM D 1525
HDT, 1.82 MPa, 3.2mm, unannealed 87 °C ASTM D 648
HDT, 0.45 MPa, 6.4 mm, unannealed 101 °C ASTM D 648
HDT, 1.82 MPa, 6.4 mm, unannealed 93 °C ASTM D 648
CTE, -30°C to 30°C, flow 7.2E-05 1/°C ASTM D 696
CTE, -30°C to 30°C, xflow 7.2E-05 1/°C ASTM D 696
Thermal Conductivity 0.2 W/m-°C ASTM C 177
Relative Temp Index, Elec 85 °C UL 746B
Relative Temp Index, Mech w/impact 85 °C UL 746B
Relative Temp Index, Mech w/o impact 85 °C UL 746B
PHYSICAL
Specific Gravity 1.18 - ASTM D 792
Water Absorption, 24 hours 0.1 % ASTM D 570
Water Absorption, equilibrium, 23C 0.4 % ASTM D 570
Mold Shrinkage, flow, 3.2 mm 0.4 - 0.6 % GE Method
Mold Shrinkage, xflow, 3.2 mm 0.4 - 0.6 % GE Method
Melt Flow Rate, 260°C/2.16 kgf 22 g/10 min ASTM D 1238
ELECTRICAL
Volume Resistivity 1.6E+17 Ohm-cm ASTM D 257

1)Typical values only. Variations within normal tolerances are possible for variose colours.All values are 2)Only typical data for material selection purpose.Not to be used forpart or tool design.
measured at least after 48 hoursstorage at 230C/50% relative humidity. 3)This rating is not intended to reflect hazards presented by this or anyother material under actual fire conditions.
All properties, expect the melt volume rate are measured on injectionmoulded samples. 4)Own measurement according to UL.
All samples are prepared according to ISO 294.

Source, GMD, Last Update:10/31/2000

PLEASE CONTACT YOUR LOCAL SALES OFFICE FOR AVAILABILITY IN YOUR AREA DISCLAIMER : THE MATERIALS AND PRODUCTS OF THE BUSINESSES MAKING UP THE GE PLASTICS UNIT OF GENERAL
ELECTRIC COMPANY, ITS SUBSIDIARIES AND AFFILIATES ("GEP"), ARE SOLD SUBJECT TO GEP' S STANDARD CONDITIONS OF SALE, WHICH ARE INCLUDED IN THE APPLICABLE DISTRIBUTOR OR OTHER
SALES AGREEMENT, PRINTED ON THE BACK OF ORDER ACKNOWLEDGMENTS AND INVOICES, AND AVAILABLE UPON REQUEST. ALTHOUGH ANY INFORMATION, RECOMMENDATIONS, OR ADVICE
CONTAINED HEREIN IS GIVEN IN GOOD FAITH, GEP MAKES NO WARRANTY OR GUARANTEE, EXPRESS OR IMPLIED, (I) THAT THE RESULTS DESCRIBED HEREIN WILL BE OBTAINED UNDER END-USE
CONDITIONS, OR (II) AS TO THE EFFECTIVENESS OR SAFETY OF ANY DESIGN INCORPORATING GEP MATERIALS, PRODUCTS, RECOMMENDATIONS OR ADVICE. EXCEPT AS PROVIDED IN GEP' S STANDARD
CONDITIONS OF SALE, GEP AND ITS REPRESENTATIVES SHALL IN NO EVENT BE RESPONSIBLE FOR ANY LOSS RESULTING FROM ANY USE OF ITS MATERIALS OR PRODUCTS DESCRIBED HEREIN.Each
user bears full responsibility for making its own determination as to the suitability of GEP' s materials, products, recommendations, or advice for its own particular use. Each user must identify and perform all tests and analyses
necessary to assure that its finished parts incorporating GEP materials or products will be safe and suitable for use under end-use conditions. Nothing in this or any other document, nor any oral recommendation or advice, shall
be deemed to alter, vary, supersede, or waive any provision of GEP' s Standard Conditions of Sale or this Disclaimer, unless any such modification is specifically agreed to in a writing signed by GEP. No statement contained
herein concerning a possible or suggested use of any material, product or design is intended, or should be construed, to grant any license under any patent or other intellectual property right of General Electric Company or any of
its subsidiaries or affiliates covering such use or design, or as a recommendation for the use of such material, product or design in the infringement of any patent or other intellectual property right
* Cycoloy is a trademark of the General Electric Company
© 1997-2006 General Electric Company.All rights reserved
Cycoloy* Resin C2950HF
Americas: COMMERCIAL
TYPICAL PROPERTIES ¹ TYPICAL VALUE UNIT STANDARD

ELECTRICAL
Volume Resistivity 1.6E+17 Ohm-cm ASTM D 257
Surface Resistivity >1.E+16 Ohm ASTM D 257
Dielectric Strength, in oil, 3.2 mm 24.3 kV/mm ASTM D 149
Relative Permittivity, 50/60 Hz 2.8 - ASTM D 150
Relative Permittivity, 1 MHz 2.7 - ASTM D 150
Dissipation Factor, 50/60 Hz 0.0052 - ASTM D 150
Dissipation Factor, 1 MHz 0.0071 - ASTM D 150
Arc Resistance, Tungsten {PLC} 6 PLC Code ASTM D 495
Hot Wire Ignition {PLC) 2 PLC Code UL 746A
High Voltage Arc Track Rate {PLC} 3 PLC Code UL 746A
High Ampere Arc Ign, surface {PLC} 0 PLC Code UL 746A
Comparative Tracking Index (UL) {PLC} 2 PLC Code UL 746A
FLAME CHARACTERISTICS
UL Recognized, 94V-2 Flame Class Rating (3) 0.76 mm UL 94
UL Recognized, 94V-0 Flame Class Rating (3) 1.49 mm UL 94
UL Recognized, 94-5VA Rating (3) 3.4 mm UL 94
UL Recognized, 94-5VB Rating (3) 2.48 mm UL 94
CSA (See File for complete listing) LS88480 File No. CSA LISTED
Oxygen Index (LOI) 30 % ASTM D 2863

1)Typical values only. Variations within normal tolerances are possible for variose colours.All values are 2)Only typical data for material selection purpose.Not to be used forpart or tool design.
measured at least after 48 hoursstorage at 230C/50% relative humidity. 3)This rating is not intended to reflect hazards presented by this or anyother material under actual fire conditions.
All properties, expect the melt volume rate are measured on injectionmoulded samples. 4)Own measurement according to UL.
All samples are prepared according to ISO 294.

Source, GMD, Last Update:10/31/2000

PLEASE CONTACT YOUR LOCAL SALES OFFICE FOR AVAILABILITY IN YOUR AREA DISCLAIMER : THE MATERIALS AND PRODUCTS OF THE BUSINESSES MAKING UP THE GE PLASTICS UNIT OF GENERAL
ELECTRIC COMPANY, ITS SUBSIDIARIES AND AFFILIATES ("GEP"), ARE SOLD SUBJECT TO GEP' S STANDARD CONDITIONS OF SALE, WHICH ARE INCLUDED IN THE APPLICABLE DISTRIBUTOR OR OTHER
SALES AGREEMENT, PRINTED ON THE BACK OF ORDER ACKNOWLEDGMENTS AND INVOICES, AND AVAILABLE UPON REQUEST. ALTHOUGH ANY INFORMATION, RECOMMENDATIONS, OR ADVICE
CONTAINED HEREIN IS GIVEN IN GOOD FAITH, GEP MAKES NO WARRANTY OR GUARANTEE, EXPRESS OR IMPLIED, (I) THAT THE RESULTS DESCRIBED HEREIN WILL BE OBTAINED UNDER END-USE
CONDITIONS, OR (II) AS TO THE EFFECTIVENESS OR SAFETY OF ANY DESIGN INCORPORATING GEP MATERIALS, PRODUCTS, RECOMMENDATIONS OR ADVICE. EXCEPT AS PROVIDED IN GEP' S STANDARD
CONDITIONS OF SALE, GEP AND ITS REPRESENTATIVES SHALL IN NO EVENT BE RESPONSIBLE FOR ANY LOSS RESULTING FROM ANY USE OF ITS MATERIALS OR PRODUCTS DESCRIBED HEREIN.Each
user bears full responsibility for making its own determination as to the suitability of GEP' s materials, products, recommendations, or advice for its own particular use. Each user must identify and perform all tests and analyses
necessary to assure that its finished parts incorporating GEP materials or products will be safe and suitable for use under end-use conditions. Nothing in this or any other document, nor any oral recommendation or advice, shall
be deemed to alter, vary, supersede, or waive any provision of GEP' s Standard Conditions of Sale or this Disclaimer, unless any such modification is specifically agreed to in a writing signed by GEP. No statement contained
herein concerning a possible or suggested use of any material, product or design is intended, or should be construed, to grant any license under any patent or other intellectual property right of General Electric Company or any of
its subsidiaries or affiliates covering such use or design, or as a recommendation for the use of such material, product or design in the infringement of any patent or other intellectual property right
* Cycoloy is a trademark of the General Electric Company
© 1997-2006 General Electric Company.All rights reserved
Cycoloy* Resin C2950HF
Americas: COMMERCIAL
PROCESSING PARAMETERS TYPICAL VALUE UNIT

Injection Molding
Drying Temperature 80 - 90 °C
Drying Time 3-4 hrs
Drying Time (Cumulative) 8 hrs
Maximum Moisture Content 0.04 %
Melt Temperature 245 - 275 °C
Nozzle Temperature 245 - 275 °C
Front - Zone 3 Temperature 245 - 275 °C
Middle - Zone 2 Temperature 220 - 265 °C
Rear - Zone 1 Temperature 220 - 255 °C
Mold Temperature 60 - 80 °C
Back Pressure 0.3 - 0.7 MPa
Screw Speed 40 - 70 rpm
Shot to Cylinder Size 30 - 80 %
Vent Depth 0.038 - 0.076 mm

1)Typical values only. Variations within normal tolerances are possible for variose colours.All values are 2)Only typical data for material selection purpose.Not to be used forpart or tool design.
measured at least after 48 hoursstorage at 230C/50% relative humidity. 3)This rating is not intended to reflect hazards presented by this or anyother material under actual fire conditions.
All properties, expect the melt volume rate are measured on injectionmoulded samples. 4)Own measurement according to UL.
All samples are prepared according to ISO 294.

Source, GMD, Last Update:10/31/2000

PLEASE CONTACT YOUR LOCAL SALES OFFICE FOR AVAILABILITY IN YOUR AREA DISCLAIMER : THE MATERIALS AND PRODUCTS OF THE BUSINESSES MAKING UP THE GE PLASTICS UNIT OF GENERAL
ELECTRIC COMPANY, ITS SUBSIDIARIES AND AFFILIATES ("GEP"), ARE SOLD SUBJECT TO GEP' S STANDARD CONDITIONS OF SALE, WHICH ARE INCLUDED IN THE APPLICABLE DISTRIBUTOR OR OTHER
SALES AGREEMENT, PRINTED ON THE BACK OF ORDER ACKNOWLEDGMENTS AND INVOICES, AND AVAILABLE UPON REQUEST. ALTHOUGH ANY INFORMATION, RECOMMENDATIONS, OR ADVICE
CONTAINED HEREIN IS GIVEN IN GOOD FAITH, GEP MAKES NO WARRANTY OR GUARANTEE, EXPRESS OR IMPLIED, (I) THAT THE RESULTS DESCRIBED HEREIN WILL BE OBTAINED UNDER END-USE
CONDITIONS, OR (II) AS TO THE EFFECTIVENESS OR SAFETY OF ANY DESIGN INCORPORATING GEP MATERIALS, PRODUCTS, RECOMMENDATIONS OR ADVICE. EXCEPT AS PROVIDED IN GEP' S STANDARD
CONDITIONS OF SALE, GEP AND ITS REPRESENTATIVES SHALL IN NO EVENT BE RESPONSIBLE FOR ANY LOSS RESULTING FROM ANY USE OF ITS MATERIALS OR PRODUCTS DESCRIBED HEREIN.Each
user bears full responsibility for making its own determination as to the suitability of GEP' s materials, products, recommendations, or advice for its own particular use. Each user must identify and perform all tests and analyses
necessary to assure that its finished parts incorporating GEP materials or products will be safe and suitable for use under end-use conditions. Nothing in this or any other document, nor any oral recommendation or advice, shall
be deemed to alter, vary, supersede, or waive any provision of GEP' s Standard Conditions of Sale or this Disclaimer, unless any such modification is specifically agreed to in a writing signed by GEP. No statement contained
herein concerning a possible or suggested use of any material, product or design is intended, or should be construed, to grant any license under any patent or other intellectual property right of General Electric Company or any of
its subsidiaries or affiliates covering such use or design, or as a recommendation for the use of such material, product or design in the infringement of any patent or other intellectual property right
* Cycoloy is a trademark of the General Electric Company
© 1997-2006 General Electric Company.All rights reserved