8 7 6 5 4 3 2 1

REVISIONS
ZONE REV DESCRIPTION ECN DATE CHG CHK APP

TYP 00 RELEASED NL14-1287 7-8-14 DTA SEM MNB

H 3/8 IT 4 & 5 A1 01 DESC L23G2 WAS L2350 NL14-2123 10-15 SEM SEM MNB H
1/2 TYP
TYP
21 3/8 IT 4 & 5 3/4 IT 26 & 29

7 7

TYP 21
1/2 IT 4 & 5
4 TYP
TYP 3/8 IT 26 & 29
3/8 IT 24 & 42
42 2 29
1/2
1/2 TYP TYP
3/4
1/2 IT 24 & 42 TYP
1/2

20
TYP
1/2 IT 20 & 43
G 46 G
18

19

TYP
1/2 TYP
SECTION A-A TYP SECTION B-B 1 IT 26 & 36
IT 7 5/8 TYP
3/8 IT 7
3/8 TYP
IT 7
97 3/4

A 48 7/8

F 15 B 22
7
F 22 F
15

9 9

42 WELD NOTES:
24 5
28 1. ALL WELDS AWS D1.1 UNLESS OTHERWISE SPECIFIED.
20 20 23
43 2. WELD MATERIAL - E70XX OR EQUIVALENT. MINIMUM CHARPY
IMPACT REQUIREMENT = 15FT LBS @ - 40°

E 3. 100% VISUAL INSPECTION OF ALL WELDS UNLESS OTHERWISE E

NOTED. ACCEPTANCE PER AWS D14.4 CLASS III CRITERIA
UNLESS OTHERWISE SPECIFIED.
29
29 4. 100% MAGNETIC PARTICLE INSPECTION OF ALL WELDS
UNLESS OTHERWISE NOTED. ACCEPTANCE PER AWS D14.4
18 ACCEPTANCE STANDARDS FOR MAGNETIC PARTICLE
8 18 INSPECTIONS UNLESS OTHERWISE SPECIFIED.

39 PAINT NOTES:

9 11/16
39 1. BLAST & PRIME WITH LET #426-4676
30 30 **DO NOT BLAST & PRIME MACHINED SURFACES**

2. PAINT FLAT BLACK WITH LET #427-4798

**DO NOT PAINT MACHINED SURFACES**
TYP 22 3/4 20
18 3/4 IT 26 & 29
8
18
D D
26 46 4281596 2 STR STOP 50YD L2350

46 B 14 45
44
4261201
4261319
2
1
BACKING STRIP OUTER L2350
BACKING STRIP MIDDLE
35 46
43 4260064 1 PLT BACKBONE TOP MIDDLE LOWER
42 4260067 2 PLT BACKBONE TOP OUTER UPPER
34 39 4260071 2 PLT COVER STOP
2 9/16 TYP
A 38 4238221 20 BASE WELD ON WEAR TLC
5 1/8 TYP 37 4269797 1 CUTTING EDGE BERK L2350
2 35 4260045 1 STR HINGE EAR OUTER LH
TYP IT 5,
3/8 8, 18, 20, 42 34 4260043 1 STR HINGE EAR INNER LH
12 1/2 TYP 33 4168470 1 WING STR LH
1 1 32 4260041 1 STR HINGE EAR MIDDLE LH
11
33
C 11 6 1/4 TYP 12 31 4260055 4 BUCKET LINER
30 0576803 2 BOLT BLK RD .375 NC .75 .50
17
29 4260061 2 GUSSET EAR TOP OUTER
C 28 4269798 1 STR END PLT LH C
27 4090379 2 TIE GUSSET
26 4260060 2 GUSSET EAR TOP INNER
25 4260058 1 GUSSET CUTTING EDGE MIDDLE
13 D 25 13 24 4260066 1 PLT BACKBONE TOP MIDDLE UPPER
23 4269799 1 STR END PLT RH
22 4211021 2 GUSSET SPILLGUARD
21 4233454 2 PLATE TOP SPILLGUARD
TYP
7/8 IT 1 & 11 20 4260065 2 PLT BACKBONE TOP OUTER LOWER
19 4260054 2 SHEET BUCKET OUTER
18 4260063 2 PLT BACK OUTER
17 4260044 1 STR HINGE EAR OUTER RH
16 4188561 2 SKID PLATE WEDGE
15 4269803 2 PLT END SPILLGUARD
J J 14 4260042 1 STR HINGE EAR INNER RH
TYP D 4 1/8 TYP 7 7/8 TYP 13 4260059 2 GUSSET CUTTING EDGE OUTER

3 1/2 TYP
5/8 IT 13 & 25 12 4168471 1 WING STR RH
B 22 7/8 TYP 8 1/4 TYP 15 3/4 TYP
11 4260069 2 SKID RUNNER OUTER
B
F 16 C 29 10 4269802 2 PLT LINER STRIP
1/2 TYP
1/2 IT 13 & 25 38 58 9 4011923 2 LIFTING EYE FRONT FRAME
8 4260062 1 PLT BACK MIDDLE
TYP 3/4 45
7 4233453 1 STR SPILLGUARD
CJP 3/4
90 6 4260053 1 SHEET BUCKET MIDDLE
5 4219918 1 PLATE SUPPORT TOP MIDDLE
131
4 4233461 2 PLATE SUPPORT TOP OUTER
262 3 4260057 2 PLT CORNER
2 4260040 1 STR HINGE EAR MIDDLE RH
298 5/16 1 4260068 2 SKID RUNNER INNER
ITEM PART NO. QTY DESCRIPTION
UNLESS OTHERWISE SPECIFIED:
FIRST USED ON/CONTRACT NO
THIS DRAWING AND ALL
DATA THEREIN IS THE
• DIMENSIONS ARE IN INCHES & APPLY BEFORE
PLATING OR FINISH COATINGS.
428-3772 LeTourneau Technologies™
PROPERTY OF LETOURNEAU DWN DATE
• TOLERANCES ON: ANGLES ±1°
TECHNOLOGIES. IT IS dandrews 7-8-14
CONFIDENTIAL AND MUST FRACTIONS ±1/16
NOT BE COPIED. IT IS CHK
.XX DECIMAL ±.03 SEM 7-8-14
A LOANED SUBJECT TO
RETURN UPON DEMAND
.XXX DECIMAL
• MACHINED CORNERS 1/64 X 45°
±.015
ENGR STR BKT 50 L23G2 BERK A
AND IS NOT TO BE USED
IN ANY WAY DETRIMENTAL • WELD PROPERTIES SHALL MEET THE MINIMUM
TO OUR INTEREST. REQUIREMENTS OF THE BASE MATERIAL.
PROD ENGR
SIZE DWG NO. REV

E
INTERPRET DIM & TOL PROJ APPROVAL
PER LETOURNEAU
THIRD ANGLE PROJECTION MNB 7-8-14 DO NOT SCALE 4283773 01
SPEC 1650.00. MATL
SCALE 1/16 EST WT 54298.7 lbm SHEET 1 OF 2

8 7 6 5 4 3 2 1
 8 7 6 5 4 3 2 1
REVISIONS
ZONE REV DESCRIPTION ECN DATE CHG CHK APP
00 RELEASED NL14-1287 7-8-14 DTA SEM MNB
H 01 SEE SHEET 1 NL14-2123 10-15 SEM SEM MNB H

E 12
33 OPP 36 11/16 TYP

15

H
9
37

TYP
1/2
E
G G
1/2
H
TYP
1/2
65 7/8 TYP

27
TYP
1/2 46
1/2
39 TYP
1/4
TYP
1/4
31 X3 TYP
F 1/2 F

O 8.253 u .003

1/2 ITEM 2, 14, 142 3/8

1/2 17, 32, 34, 35
1/2

1 1/2
TYP R 36 u 1/32
1 1/2
17
35 OPP

TYP
ITEM 10
1/2
3 SIDES

E E

3/8
2 G TYP
3/8 G
32 OPP

O 5.750 u .001

14

19 1/16 REF
10 34 OPP

37

D D
SECTION G-G
K
TYP
TYP 5/8
IT 2, 14, 17, 16
32, 34, 35 5/8 TYP
CJP 5/8 IT 1 & 11 2 13/16 86 1/8 6 1/4 ±1/32

13 1/8
TYP 10 PLCS 45
9 1/2
TYP 10 PLCS VIEW F-F
TYP 20 PLCS

TYP 23 TYP
IT 2, 14, 17,
3/4 32, 34, 35 38 20X DETAIL K TYP
1/2 IT 12 & 33
CJP
1:4 IT 12 & 33 1/2

C 37
19 C

11
3
TYP
5/8 CJP
TYP 22 21
19 CJP 5/8 31 12
CONTINUOUS JOINT
44 1 1/2 PREHEAT TO 250v 22

7
SECTION C-C
TYP 16 PLCS

13

1/4 PREHEAT TO 300°

CJP UT
3

1
B
SEE NOTE 4
TYP
SECTION E-E B
BOTH ENDS 5/8 ROTATED CW 90°
DETAIL K SECTION H-H
5/8
TYP ROTATED CCW 21.3°
5/8
TYP 4 PLCS
1 11/16

TYP
3/4

37

A K 25 TYP A
3/4 IT 13 & 25
SECTION D-D STR BKT 50 L23G2 BERK
VIEW J-J 16 SIZE DWG NO. REV

DRAWN dandrews E DO NOT SCALE 4283773 01

ISSUED 7-8-14 SCALE 1:8 EST WT 54298.7 lbm SHEET 2 OF 2

8 7 6 5 4 3 2 1