Designers & Manufactures of Bearing Housings

ARVIS ® PLAIN BEARINGS

 CONTENTS

03 Introduction

05 Arvis ® Pre-Mounted Plain Bearings for Constant Re-Alignment

08 Arvis® Housing Performance

10 PB Metric self aligning pillow block range with DU and DX bushes (dims only)

12 FL Metric self aligning 4 bolt flange block range with DU and DX bushes (dims only)

14 DF Metric self aligning 2 bolt flange block range with DU and DX bushes (dims only)

16 PB Imperial self aligning pillow block range with DU and DX bushes (dims only)

18 FL Imperial self aligning 4 bolt flange block range with DU and DX bushes (dims only)

20 DF Imperial self aligning 2 bolt flange block range with DU and DX bushes (dims only)

22 Special Arvis® Bearing Units

24 FLS Split 4 Bolt Flange Blocks Introduction

26 FLS Split 4 Bolt Flange Blocks Dimensions

02
INTRODUCTION

Plain bearings, also referred to as bushings, sleeve bearings, Plain bearings offer many advantages:
solid bearings, shaft bearings, or journal bearings, are
differentiated from roller bearings by the fact that plain » Higher load capacity, especially for shock load resistance
bearings have no rolling elements. and a greater contact zone

Plain bearings reduce friction by using highly specialised bearing » Compensation for misalignment and vibration damping with
materials, such as PTFE or graphite, to facilitate movement a conformal liner
between two surfaces. Plain bearings can be either self-lubricating
or externally lubricated.
» Reduced noise due to the absence of moving parts

» Space and weight savings

High quality plain bearings are defined by the bearing
material used, which includes metal-polymer, fiber reinforced » Straightforward and simple maintenance and installation
composite, metal or bi-metal and engineered plastic. Plain
bearings are commonly used in static oscillatory applications » Low initial and overall cost

such as hinges, pivots and linkages. One special subtype of plain

» High Temperature
bearing is a spherical plain bearing, which can accommodate
moderate misalignment.

Arvis ® offers a variety of plain bearings that can

replace roller bearings.

www.arvis.co.uk 03
Arvis ® Bearings are being used extensively throughout the
world for the past 40 years in the following industries:

» Steel works
» Quarry plant
» Agricultural plant
» Conveyors
» Materials and handling
» Food machinery
» Printing machinery
» Heating and ventilation
» Lifts and cranes
» Machine tools
» Furnaces
» Foundry plant
» Hosiery Machines
» Textile Machinery
» Mining equipment
» Special purpose machinery
» Bakery equipment
» Chemical plant
» Marine applications

04
ARVIS ® PRE-MOUNTED PLAIN
BEARINGS FOR CONSTANT
RE-ALIGNMENT

DU or DX steel backed bearings are pre-mounted in

captive inner members. The spherical seating allows
constant re-alignment of up to 15° during operation
& eliminates the need for precise positioning and
alignment during installation.

The working clearance of the bearings on the shaft

means no press fitting is needed as with some
rolling element bearings.

Excellent load carrying capacity prevents edge loading thus

allowing full use to be made of DU & DX performance.
Proven characteristics of DU & DX are long life with
minimum maintenance. Sealing is unnecessary in most
cases. Shaft location can be achieved by use of locking
collars, if moderate thrust loads are expected standard
thrust washers can be included.

www.arvis.co.uk 05
A choice of three housing styles, pillow
block, two bolt flange & four bolt flange
gives versatility for mounting.

Metric sizes from 10mm to 100mm & inch

sizes from ½ " to 4" are offered as standard.
Larger sizes are available to order.

The standard housings are made in grey

cast iron & together with the DU & DX
materials ensure low operating costs.

Both bush materials are supplied with

pre-finished bores. Other materials are
available on request. See 'Specials' page.

06
 DU is a high performance dry-bearing
material used where lubrication is
impracticable or undesirable & where the
operating temperature is between -200 °C
& +280 °C. It will also perform exceptionally
well in water, oil & other liquids.

DX gives outstanding performance when

greased on assembly only. Regreasing at
extended intervals prolongs performance
indefinitely. DX can withstand temperatures
from -40 °C up to 130 °C for short periods.

Plain bearing materials can be used in

high load applications. The maximum
permissible loading for the bush,
particularly at low rubbing speeds, may
exceed that for the housing. Where such
conditions are likely to occur, design advice
should be obtained.

www.arvis.co.uk 07
ARVIS ® HOUSING PERFORMANCE.
Estimated safe radial loads for units based on the strength of the cast iron outer housing.

Arvis ® plain bearings materials can be used in high load applications. The maximum permissible loading for the bush, particularly at low
rubbing speeds may exceed that for the Arvis ® housing or securing bolts.

» Step 1 - Check from the table below that the load does not exceed the limit for the cast iron housing.

» Step 2 - For full technical information on the various bushes, contact the Arvis ® sales team.

» Step 3 - Note that the thermal conductivity of these units is such that, in the 'Application Factor' for both
DU & DX calculations a housing of a 'Light pressing' nature should be used.

Casting No Bush Sizes Maximum Bearing Load

PB Type FL & DF
mm Inch Kg Ibf Kg Ibf
1 10 12 15 1/2 3/8 3/4 432 950 386 850
2 20 25 - 7/8 1 - 770 1700 590 1300
3 30 - - 1 1/8 1 1/4 - 955 2100 818 1800
4 35 40 - 1 3/8 1 1/2 1 5/8 1730 3800 1100 2400
5 45 - - 1 3/4 - - 2300 5100 1200 2600
6 50 - - 1 7/8 2 - 2500 5500 1450 3200
7 55 60 65 2 1/4 - - 3050 6700 1600 3500
8 70 75 - 2 1/2 2 3/4 - 2800 6200 1730 3800
9 80 85 - 3 - - 4550 10000 2700 5900
10 90 100 - 3 1/2 4 - 7450 16400 3050 6700

08
For Higher loads consult our sales department.
Materials
Standard bearing housings are made in grey cast iron. Other
materials are available (See 'Specials') Bearings can be specified in
DU or DX material according to requirement. Both materials are
supplied with pre-finished bores.

Selection
As a general guide on selection. DU is a high performance
dry-bearing material, used where lubricant is impracticable or
undesirable and where the operating temperature is between
-200ºC and +280ºC. DX gives outstanding performance when
greased on assembly only. Re-greasing at extended intervals
prolongs performance indefinitely. DX is suitable for operating
temperatures up to 120ºC.

Specials
Pre-mounted self-aligning bearings other than the standards listed
in this leaflet can be supplied to special order

Variations from standard include: Bearings for shaft diameters

over 100mm - Split housings to allow for assembly in awkward
locations or to provide a greater length of bearing. Housings with
provision for re-greasing (As an alternative. re-greasing can be
through shaft end drilling). Housing for special applications made in
SG iron or corrosion resistant materials.

www.arvis.co.uk 09
 PB

Metric

PLUMMER BLOCK

SHAFT DIA SHAFT TOLERANCE

DU DX

10mm – 75mm f7 h8

> 75mm H8 H8

10
D Part No E H C B (bolt) L W T R G N
PB1-10M-DU
10 15 28.6 76 M8 102 25 10 56 33.3 13
PB1-10M-DX
PB1-12M-DU
12 15
PB1-12M-DX
PB1-15M-DU
15 15
PB1-15M-DX
PB2-20M-DU
20 20 33.3 95 M10 124 32 13 65 39.7 16
PB2-20M-DX
PB2-25M-DU
25 25
PB2-25M-DX
PB3-30M-DU
30 30 41.3 122 M12 159 41 16 81 51 22
PB3-30M-DX

35 PB4-35M-DU 35 49.2 137 M12 183 48 16 98 60.3 19

PB4-35M-DX
PB4-40M-DU
40 40
PB4-40M-DX
PB5-45M-DU
45 45 54 153 M12 194 55 16 113 73 22
PB5-45M-DX
PB6-50M-DU
50 50 61.9 167 M16 214 56 19 125 79.3 22
PB6-50M-DX
PB7-55M-DU
55 55 66.7 197 M16 247 64 22 135 83 22
PB7-55M-DX
PB7-60M-DU
60 60
PB7-60M-DX
PB7-65M-DU
65 60
PB7-65M-DX
PB8-70M-DU
70 65 71.4 200 M16 254 70 26 143 89 23
PB8-70M-DX
PB8-75M-DU
75 65
PB8-75M-DX
PB9-80M-DU
80 80 87.3 235 M20 292 89 32 175 108 32
PB9-80M-DX
PB9-85M-DU
85 80
PB9-85M-DX
PB10-90M-DU
90 80 101.6 279 M20 330 102 32 207 130 32
PB10-90M-DX
PB10-100M-DU
100 80
PB10-100M-DX
 FL

Metric

FOUR BOLT FLANGE

SHAFT DIA SHAFT TOLERANCE

DU DX

10mm – 75mm f7 h8

> 75mm H8 H8

12
D Part No E C B (bolt) L T W A F G
FL1-10M-DU
10 15 57 M8 76 8 23 54 6 33.3
FL1-10M-DX
FL1-12M-DU
12 15
FL1-12M-DX
FL1-15M-DU
15 15
FL1-15M-DX
FL2-20M-DU
20 20 64 M10 89 10 27 64 10 39.7
FL2-20M-DX
FL2-25M-DU
25 25 30
FL2-25M-DX
FL3-30M-DU
30 30 79 M12 110 11 36 79 13 51
FL3-30M-DX
FL4-35M-DU
35 35 92 M12 121 14 43 95 16 60.3
FL4-35M-DX
FL4-40M-DU
40 40
FL4-40M-DX
FL5-45M-DU
45 45 102 M12 133 16 51 108 16 73
FL5-45M-DX
FL6-50M-DU
50 50 111 M12 143 16 58 117 21 79.3
FL6-50M-DX
FL7-55M-DU
55 55 130 M16 165 17 62 137 22 83
FL7-55M-DX
FL7-60M-DU
60 60 65
FL7-60M-DX
FL7-65M-DU
65 60 65
FL7-65M-DX
FL8-70M-DU
70 65 143 M16 175 19 71 145 25 89
FL8-70M-DX
FL8-75M-DU
75 65
FL8-75M-DX
FL9-80M-DU
80 80 152 M20 197 20 81 171 29 108
FL9-80M-DX
FL9-85M-DU
85 80
FL9-85M-DX
FL10-90M-DU
90 80 197 M20 241 25 91 210 32 130
FL10-90M-DX
FL10-100M-DU
100 80
FL10-100M-DX
FL10-120M-DU
120 80 197 M20 241 25 82.5 210 32 130
FL10-120M-DX
FL11-120M-DU
120 120 260 M24 340 45 132 300 40 190
FL11-120M-DX
 DF

Metric

TWO BOLT FLANGE

SHAFT DIA SHAFT TOLERANCE

DU DX

10mm – 75mm f7 h8

> 75mm H8 H8

14
D Part No E C B (bolt) L T W A F G
DF1-10M-DU
10 15 81 M8 103 8 23 54 6 33.3
DF1-10M-DX
DF1-12M-DU
12 15
DF1-12M-DX
DF1-15M-DU
15 15
DF1-15M-DX
DF2-20M-DU
20 20 89 M10 116 10 27 64 10 39.7
DF2-20M-DX
DF2-25M-DU
25 25 30
DF2-25M-DX
DF3-30M-DU
30 30 113 M10 143 11 36 80 13 51
DF3-30M-DX

35 DF4-35M-DU 35 130 M12 159 14 43 92 16 60.3

DF4-35M-DX
DF4-40M-DU
40 40
DF4-40M-DX
DF5-45M-DU
45 45 144.5 M12 175 15 51 108 16 73
DF5-45M-DX
DF6-50M-DU
50 50 157 M12 190 16 58 117 21 79.3
DF6-50M-DX
DF7-55M-DU
55 55 184 M16 216 17 62 137 22 83
DF7-55M-DX
DF7-60M-DU
60 60
DF7-60M-DX
DF7-65M-DU
65 60
DF7-65M-DX
DF8-70M-DU
70 65 202 M16 236 19 71 143 25 89
DF8-70M-DX
DF8-75M-DU
75 65
DF8-75M-DX
DF9-80M-DU
80 80 214 M20 259 22 81 171 27.7 108
DF9-80M-DX
DF9-85M-DU
85 80
DF9-85M-DX
DF10-90M-DU
90 80 279 M20 324 25 91 207 29.7 130
DF10-90M-DX
DF10-100M-DU
100 80
DF10-100M-DX
 PB

Imperial

PLUMMER BLOCK

SHAFT DIA SHAFT TOLERANCE

DU DX

½” TO 3” f7 h8

> 3” H8 H8

16
 D Part No E H C B (bolt) L W T R G N
PB1-08E-DU
1/2 0.625 1.125 3 0.312 4 1 0.375 2.187 1.312 0.5
PB1-08E-DX
PB1-10E-DU
5/8 0.625
PB1-10E-DX
PB1-12E-DU
3/4 0.75
PB1-12E-DX
PB2-14E-DU
7/8 0.875 1.312 3.75 0.375 4.875 1.25 0.5 2.562 1.562 0.625
PB2-14E-DX
PB2-16E-DU
1 1
PB2-16E-DX
PB3-18E-DU
1 1/8 1 1.625 4.812 0.5 0.25 1.625 0.625 3.187 2 0.875
PB3-18E-DX

1 1/4 PB3-20E-DU 1.25

PB3-20E-DX
PB4-22E-DU
1 3/8 1.375 1.937 5.375 0.5 7.187 1.875 0.625 3.875 2.375 0.75
PB4-22E-DX
PB4-24E-DU
1 1/2 1.5
PB4-24E-DX
PB4-26E-DU
1 5/8 1.5
PB4-26E-DX
PB5-28E-DU
1 3/4 1.75 2.125 6 0.5 7.625 2.125 0.625 4.437 2.875 0.875
PB5-28E-DX
PB6-30E-DU
1 7/8 1.875 2.437 6.6 0.625 8.4 2.25 0.75 4.812 3.125 0.875
PB6-30E-DX
PB6-32E-DU
2 2
PB6-32E-DX
PB7-36E-DU
2 1/4 2.25 2.625 7.75 0.625 9.75 2.5 0.875 5.312 3.625 0.875
PB7-36E-DX
PB8-40E-DU
2 1/2 2.5 2.812 7.875 0.625 10 2.75 1 5.625 3.75 0.9
PB8-40E-DX
PB8-44E-DU
2 3/4 2.5
PB8-44E-DX
PB9-48E-DU
3 3 3.437 9.25 0.75 11.5 3.5 1.25 6.875 4.25 1.25
PB9-48E-DX
PB10-56E-DU
3 1/2 3 4 11 0.75 13 4 1.25 8.125 5.125 1.25
PB10-56E-DX
PB10-64E-DU
4 3
PB10-64E-DX
 FL

Imperial

FOUR BOLT FLANGE

SHAFT DIA SHAFT TOLERANCE

DU DX

½” TO 3” f7 h8

> 3” H8 H8

18
 D Part No E C B (bolt) L T W A F G
FL1-08E-DU
1/2 0.625 2.25 0.312 3 0.312 0.937 2.125 0.25 1.312
FL1-08E-DX
FL1-10E-DU
5/8 0.625
FL1-10E-DX
FL1-12E-DU
3/4 0.75 1
FL1-12E-DX
FL2-14E-DU
7/8 0.875 2.5 0.375 3.5 0.375 1.125 2.5 0.375 1.562
FL2-14E-DX
FL2-16E-DU
1 1 1.187
FL2-16E-DX
FL3-18E-DU
1 1/8 1 3.125 0.5 4.312 0.437 1.312 3.125 0.5 2
FL3-18E-DX

1 1/4 FL3-20E-DU 1.25 1

FL3-20E-DX
FL4-22E-DU
1 3/8 1.375 3.625 0.5 4.75 0.562 1.437 3.75 0.625 2.375
FL4-22E-DX
FL4-24E-DU
1 1/2 1.5 1.75
FL4-24E-DX
FL4-26E-DU
1 5/8 1.5 1.75
FL4-26E-DX
FL5-28E-DU
1 3/4 1.75 4 0.5 5.25 0.625 2 4.25 0.625 2.875
FL5-28E-DX
FL6-30E-DU
1 7/8 1.875 4.375 0.5 5.625 0.625 2.25 4.625 0.812 3.125
FL6-30E-DX
FL6-32E-DU
2 2 2.312
FL6-32E-DX
FL7-36E-DU
2 1/4 2.25 5.125 0.625 6.5 0.687 2.5 5.375 0.875 3.625
FL7-36E-DX
FL8-40E-DU
2 1/2 2.5 5.625 0.625 6.875 0.75 2.75 5.625 1 3.75
FL8-40E-DX
FL8-44E-DU
2 3/4 2.5
FL8-44E-DX
FL9-48E-DU
3 3 6 0.75 7.75 0.875 3.125 6.75 1.125 4.25
FL9-48E-DX
FL10-56E-DU
3 1/2 3 7.75 0.75 9.5 1 3.5 8.25 1.25 5.125
FL10-56E-DX
FL10-64E-DU
4 3
FL10-64E-DX
 DF

Imperial

TWO BOLT FLANGE

SHAFT DIA SHAFT TOLERANCE

DU DX

½” TO 3” f7 h8

> 3” H8 H8

20
 D Part No E C B (bolt) L T W A F G
DF1-08E-DU
1/2 0.625 3.187 0.312 4.062 0.312 0.937 2.125 0.25 1.312
DF1-08E-DX
DF1-10E-DU
5/8 0.625 0.937
DF1-10E-DX
DF1-12E-DU
3/4 0.75 1
DF1-12E-DX
DF2-14E-DU
7/8 0.875 3.5 0.375 4.562 0.375 1.125 2.5 0.375 1.562
DF2-14E-DX
DF2-16E-DU
1 1 1.187
DF2-16E-DX
DF2-16E-DU
1 1/8 1 4.437 0.375 5.625 0.437 1.312 3.125 0.5 2
DF2-16E-DX
DF3-20E-DU
1 1/4 1.25 1.437
DF3-20E-DX
DF4-22E-DU
1 3/8 1.375 5.125 0.5 6.25 0.625 1.687 3.625 0.625 2.375
DF4-22E-DX
DF4-24E-DU
1 1/2 1.5 1.75
DF4-24E-DX
DF4-26E-DU
1 5/8 1.5 1.75
DF4-26E-DX
DF5-28E-DU
1 3/4 1.75 5.687 0.5 6.875 0.625 2 4.25 0.625 2.875
DF5-28E-DX
DF6-30E-DU
1 7/8 1.875 6.187 0.5 7.5 0.625 2.25 4.625 0.812 3.125
DF6-30E-DX
DF6-32E-DU
2 2 2.312
DF6-32E-DX
DF7-36E-DU
2 1/4 2.25 7.25 0.625 8.5 0.687 2.25 5.375 0.875 3.625
DF7-36E-DX
DF8-40E-DU 7.937 0.625 9.312 0.75 2.75 5.625 1 3.75
2 1/2 2.5
DF8-40E-DX
DF8-44E-DU
2 3/4 2.5 2.75
DF8-44E-DX
DF9-48E-DU
3 3 8.437 0.75 10.187 0.875 3.125 6.75 1.125 4.25
DF9-48E-DX
DF10-56E-DU
3 1/2 3 11 0.75 12.75 1 3.5 8.25 1.25 5.125
DF10-56E-DX
DF10-64E-DU
4 3 3.5
DF10-64E-DX
SPECIAL ARVIS ® BEARING UNITS

Arvis ® bearing units offer the opportunity for an almost HOUSINGS

Infinite combination of housing & bush materials.
Standard housings can be painted or plated
In addition to standard sizes, bores in between those offered & far to any specification. Re-grease facilities can
in excess of 100mm & 4" can be supplied. be included.

Stainless steel housings & inserts can be

supplied for the food or marine industries as
well as the chemical industry, sewage & water
treatment plants where corrosion resistance
is required.

The use of structural mild steels gives

strength for heavy handling or for reasons of
safety.

In fact, any commercially available material

can be used.Units can be split to aid fitting
where access is limited.

22
BUSHES
In addition to the standard DU &
DX, the variety of bearing materials
available means that Arvis ® Bearings
can be used in almost any environment.

Carbon graphite is ideal for

temperatures up to 500°C & can
operate in temperatures up to 1000°C
under certain condition. A wide variety
of Engineering plastics & self-lubricating
materials such as Arvis ® DRSL as well
as phosphor bronze & Deva. Metal give
the widest possible choice of bushings
for all applications.

www.arvis.co.uk 23
 FLS

SPLIT 4 BOLT FLANGE BLOCKS

The FLS range of fully split self aligning bearing

units are able to withstand continuous
misalignment and oscillating shaft movements.

The manufacturing facilities offered by the

company enable bushes to be supplied in a variety
of materials to suit specific applications. Some
information and links to plain bearing materials
can be found by visiting www.arvis.co.uk.

24
Arvis ® have manufactured a number of split four bolt
flanged housings during recent years. As the demand for
this style of product has increased a standard FLS range has
been produced.

Split units have resulted in minimised down times during

replacement or maintenance as the need for shaft removal is
eliminated in the majority of applications. This ensures that the
units can be fitted without causing disturbance to surrounding
parts such as couplings or gearboxes. Bolt hole positions are
manufactured to allow the split units to be interchangeable with
the standard four bolt flange.

Self aligning inserts can be manufactured from any commercially

available material and infinitely variable bush materials are also
available on request. Bushes for the split units can be supplied
in materials to suit specific applications. This results in optimum
bearing life and performance.

www.arvis.co.uk 25
 FLS

DIMENSIONS
Find out what group of
castings your shaft size falls
into from the list below,

Contact the Arvis ® sales

team who will be pleased to
deal with your enquiry and
advise on the suitability.

26
Key: XX Shaft Size ## Bush Material E Imperial (in 16ths of Inch) e.g. 2” = 32E M Metric (mm) PB PB e.g. Phosphor Bronze

Metric

D Range Part No C B L2 L1 W
10 -19 FL1S-XXM-## 57.15 8.0 76.2 88.0 24
19.05 – 25.5 FL2S-XXM-## 63.5 9.5 89.0 110.0 28.6
25.5 -28.5 FL3S-XXM-## 79.0 13.0 110.0 122.0 36.9
28.6 – 41.3 FL4S-XXM-## 92.1 14.3 121.0 158.8 45.4
41.3 – 44.5 FL5S-XXM-## 101.6 13.0 133.4 172.0 50.8
44.6 – 51 FL6S-XXM-## 111.0 14.3 142.9 184.2 58.4
51.1 – 57.1 FL7S-XXM-## 130.0 17.5 165.0 219.0 63.5
57.15 – 69.86 FL8S-XXM-## 143.0 16.0 174.5 235.0 69.85
69.87 – 100 FL9S-XXM-## 152.0 21.5 195.0 258.0 81.28
82.57 - 100 FL10S-XXM-## 197.0 22.0 240.0 324.0 88.9

Imperial

D Range Part No C B L2 L1 W
0.5 -0.750 FL1S-XXE-## 2.250 0.312 3.000 3.465 0.937
0.751 – 1.00 FL2S-XXE-## 2.500 0.375 3.500 4.300 1.125
1.001 – 1.125 FL3S-XXE-## 3.125 0.500 4.330 4.812 1.45
1.126 -1.625 FL4S-XXE-## 3.652 0.562 4.750 6.250 1.785
1.626 – 1.750 FL5S-XXE-## 4.000 0.500 5.250 6.770 2.000
1.751 -2.000 FL6S-XXE-## 4.375 0.5625 5.625 7.250 2.300
2.001 – 2.250 FL7S-XXE-## 5.125 0.687 6.500 8.625 2.500
2.251 – 2.750 FL8S-XXE-## 5.625 0.625 6.875 9.250 2.750
2.751 – 3.250 FL9S-XXE-## 5.984 0.846 7.7 10.125 3.200
3.251 -4 FL10S-XXE-## 7.750 0.875 9.500 12.75 3.500

www.arvis.co.uk 27
Bridge Park Rd, Thurmaston, Leicester, LE4 8BL, UK

T +44 (0) 116 2609700

F +44 (0) 116 2640147
E Sales@arvis.co.uk

www.arvis.co.uk