Hammond Organ Service Manual Models M

n
IM
INGLUDINe PARTS LIST
CAUTION
SEE SAFETY NOTICE ON
H 000-006059
INSIDE
COVER SHEET
ORGAN SERVICE COMPANY

6475 JOLIET
ROAD
SUITE B-t
LaGRANGE ILLINOIS 60525 PHONE 708-352-8011
SAFETY NOTICE
Great care has bean taken In the design and manufacture of this product to assure that no shock hazard exists on any exposed metal parts. Internal service operations can expose the technician to hazardous line voltages and accidentally cause these voltages to appear on exposed metal parts during repair or reassembly of product components. To prevent this, work on these products should oniy be performed by those who are thoroughly familiar with the precautions necessary when working on this type of equipment.
To protect the user,
required that all enclosure parts and safety Interlocks be rettored to their original condition and the following tests be performed before returning the product to the owner aftor any service operation.
It Is
receptacle (do not use an Isolation transformer for this test) and turn the product on. Connect the network (as shown below) In
iine
Plug the
AC
cord directiy Into a line voltage
AC
senes with all exposed metal parts and a Known earth ground such as a water pipe or conduit. Use an AC VOM of 5,000 ohms per volt or higher sensitivity to measure the voltage drop across the network. Move the network connection to each exposed metal part (metal chassis, screw heads, knobs and control shafts, escutcheon, etc.) and measure the voltage drop across the network. Reverse the line plug and repeat the measurements. Any reading of 4 volts RMS or more is excessive and indicates a potential shock hazard which must be corrected before returning the product to the user.
VOM AC SCALE
OK
n
I I
.01
Mf
CERAMIC RF BYPASS CAP

TEST CLIPS
TEST PROBE
CONNECTEQ TO WQWN EARTK ORQUHO

EXPOSED HETAL PARTS
TO
TABLE OF CONTENTS
PAGE
PAGE ONE KEY DOES NOT PLAY

19
GENERAL DESCRIPTION
INSTALLATION AND MAINTENANCE
ONE NOTE IS WEAX

PERCUSSION NOTES VEAK
PEDAL NOTE SOUNDS AT FULL VOLUME PEDAL NOTE SOUNDS FAINTLY
20
2I
MUSICAL TERMS
NOTES AND OCTAVES
21 21 21
HABMONICS OR OVERTONES
BOW THE ORGAN WORKS
HUM
7
CONSTRUCTION AND OPERATION OF COMPONENTS

MOTORS AND POWER SWITCHES
TONE GENERATOR
REPLACING TUBES
22 22
22 22 23 23
PROCEDURE FOR REMOVING PARTS

UPPER MANUAL KEY
MANUALS
HARMONIC DRAWBARS
8 9
LOWER MANUAL KEY
DRAWBAR CONTACT SPRING DRAWBAR OR DRAWBAR KNOB

UPPER MANUAL LOWER MANUAL
PEDAL DRAWBAR
9
9
PEDAL KEYBOAIU)
EXPRESSION PEDAL
24
25
10 10 10
11
+
CONTROL TABLETS
PERCUSSION CONTROL TABS
VIBRATO TABS
PRESET TABS
CONTROL PANEL ACCESS

PERCUSSION SWITCH ACCESS
26
26
GENERATOR
STARTING MOTOR
26 26
12
REVERBERATION-VOLUME SOFT TABS

AMPLIFIER ASSEMBLY
,,.12
12
PILOT LIGHT
26
TAB SWITCH
26A
MANUAL SECTION OF AMPLIFIER

PEDAL SECTION OF AMPLIFIER
13
I
VIBRATO LINE BOX

PEDAL KEYBOARD
EXPRESSION PEDAL
26A 26A
26A
77 78
&
INTERMEDIATE SECTION OF AMPLIFIER

OUTPUT SECTION OF AMPLIFIER
15
,.,. 15
PRESET PERCUSSION UNIT

SELECTOR SWITCH
PERCUSSION SECTION OF AMPLIFIER
16
17
POWER SUPPLY
HARMONIC BUSBAR SWITCHING
REIT- SPLIT
78 78 79 79
TUBE SOCKET VOLTAGES

REVERBERATION AMPLIFIER
SPECIAL EQUIPMENT
RADIO, PHONOGRAPH, OR MICROPHONE
H
17 18
18
18
UPPER MANUAL
MODE SWITCH
FREQUENCY DIVIDER
CYMBAL AND BRUSH
BRUSH KEi'ING
.
80 80 80 80
81
EXTENSION SPEAKER
EAR PHONES
IS
19
CYMBAL KEYING
SPECIAL POV,^R SOURCES
CXMBAL-BRUSH AMPLIFIER AND NOISE GATE

CH.\NnES
PRACTICAL SERVICE SUGGESTIONS

ORGAN DOES NOT PLAY
19
19
AM
REVISIONS
IiKTALLr\TION AND MAINTENANCE
BACK COVER
... .
LIST OF FIGURES AND ILLUSTRATIONS
FIGURE
1
PAGE
Front View of Console - Model M Front View of Console - Model M-2

Back View of Console - Model M, M-2
27 28 29
2.
3.
4. 5.
Front View of Console - Model M-3

Back View of Console - Model M-3
30
31
6. 7. 8.
9
Front View of Console - Model M-lOO

Back View of Console - Model M-lOO
32 33 34
Block Diagram - Model M
."
Block Diagram - Model M-2

,
34 35
35 36
. , , .
10.
11. 12.
Block Diagram - Mcdel M-3 Block Diagram - Model M-lOO
Typical Tone Generator

Magnet Locations on Tone Generator
13. 14
36
37
Generator Cover - Model M Generator Cover - Model M - Serial 15083 and Up Generator Cover - Model M, M-2, M-3
14A.
15.
16
37 38
Generator Cover - Model M-3
90485 and above
39 40
41
17.
Generator Cover - Model M-lOO

Manual Wiring Chart
18. 19.
Drawbar Assembly
Pedal Keyboard Assembly - M, M-2, M-3
Pedal Keyboard Assembly - M-lOO
42 42 43
43
20. 21. 22. 23.

24.
Fundamental Vibrato System - M
Vibrato System - Model M - 13509 and below Vibrato System

-
44 44 45
Model M - 13509 and above

- M-2,
25.
Fundamental Vibrato System
M-3
LIST OF FIGURES AND ILLUSTRATIONS CONTINUED
FIGURE
PAGE
26. 27. 28. 29.
Fundamental Vibrato System - M-lOO

Vibrato Line Box-Model M, M-2 Vibrato Line Box - M-3
46
46
47
47
Vibrato Line Box - M-lOO Vibrato Scanner Vibrato System M-2

-
30.
31.
47
Serial 19000 to 22253
48 48 49 50
51
32. 33.
34. 35. 36.
Vibrato System M-2 - Serial 25254 and above
Manual Hold Down Screws
(M,
M-2, M-3)
Pictorial - Model M Amplifier
Pictorial - Model M Amp.
- Serial 8411 and above
Pictorial - Model M-2 Amp. Serial 19000 and above Pictorial - Model M-3 Amp (Partial)
Pictorial - Model M-3 Amp
Schematic AO-35 Reverberation Amp M-lOO Schematic AO-44 Reverberation Amp M-lOO Schematic AO-44 - See Serial Numbers Schematic AO-66 Reverberation Amp (Later Model M-lOO) Schematic Model M
52 53 54 55
56 57 58 59
36A. 36B.
37. 38.
38A.
39.
40.
41.
Wiring Diagram Model M

Wiring Diagram Model M - Serial 15083 and above Schematic Model M-2 - 19000 and above
60
61
41A.
42. 43.
62
63
Wiring Diagram Model M-2
Serial 19000 and above
43A.
44.
Wiring Diagram Model M-2 - Serial 25254 and above

Schematic Model M-3
F
64 65
66
67
44A.
44B.
45.
Schematic Model M-3 Serial 90485 and above Schematic Model M-3 - Serial 109466 and above
Wiring Diagram Model M-3
68
. .
LIST OF FIGURES AND ILLUSTRATIONS CONTINUED
FIGURE
PAGE
45A.
46.
Wiring Diagrams Model M-3 - Serial 90485 and above

Schematic Model M-lOO with AO-35 and AO-29
69
70
71
4748.
49.
50
Schematic Model M-lOO with AO-44 and AO-29

Schematic Model M-lOO with AO-66 and AO-67 Wiring Diagram M-lOO with AO-35 Amp Wiring Diagram M-lOO with AO-44 Amp
72
73
74
,
51.
i
Wiring Diagram M-lOO Control Panel M-IOOA SUPPLEMENT
73
52.
53. 54. 55.
M-IOOA Percussion Kit Wiring Diagram

Brush and Cymbal Wiring Diagram with AO-66 Amp
Brush and Cymbal Wiring Diagram with AO-44 Amp
82 83 ^
85 87
Schematic - Percussion Preset Unit

Schematic Diagram Model M-IOOA
56.
57
58.
Wiring Diagram Model M-IOOA
88
89
Percussion Kit Circuit Board Component Layout
GENERAL DESCRIPTION
The Hammond Organ "m" Series Spinet Consoles are completely self contained, requiring no external tone cabinet. All Models have two (2) manuals of forty-four (44) keys each, a 12 (M, M-2, M-3) or 13 (M-lOO) note pedal keyboard, and an expression (or swell) pedal for controlling the volume. All tones are produced by electro-magnetic tone generators and electrically amplified. Selection of tone colors is made by adjusting eighteen(18) drawbars, and other characteristics of the music are adjusted by means of tilting control tablets and tab switches. A push button and a toggle switch or two toggle switches located in the front of the Console are used to turn on the organ.
Figures 1 thru 7 show the front and rear views of the "M" Series Models- The rear views are shown with the dust covers removed. Console rear panels are an optional accessory and are not shown.
INSTALLATION AND MAINTENANCE
A card packed with the playing instructions or located in the bench gives full information on installing the organ, oiling, and packing for moving or shipment. (See Back Cover)
MUSICAL TERMS
The service man who has had no musical training will find the following information helpful in studying the operation of the organ.
NOTES AND OCTAVES Keyboard instruments are divided into 'ôctaves" of 12 keys or notes, each with spven (7) ''naturals" (white keys) and five (5) "sharps" or "flats" (black keys) in a definite sequence. Black keys occur in groups of two and three in each octave and offer a convenient way to identify the notes of the octave. Technically there is no difference between a black key and a white one, since each key has a frequency 1.059 times the frequency of the next one below it.
Each note has a frequency exactly one half that of the corresponding note in the next higher octave. Each white key is called by a letter for A to G and these letters are known as "note of the musical scale", A black key may be called a "sharp"of the notes below it or a '^flat" of the notes above it; for instance, the black key between C and D may properly be called Cif (Sharp) or D*^ (D flat).
HARMONICS OR OVERTONES Any musical note has a definite fundamental pitch or frequency and also a certain "tone quality" or "timbre" depending on its wave shape. A complex note is one which includes not only a fundamental frequency but also one or more "harmonics" or "overtones," each of which is an integral multiple of the fundamental frequency. Such a combination is more pleasing musically than a note having only a single frequency. The ear does not distinguish the harmonics independently but instead identifies the note as a complex tone having the pitch of the lowest component, or fundamental
,
.
HOW THE ORGAN WORKS

Most tone sources, such as strings, reeds or pipes, produce complex tones The Hammond tone producing mechanism, however, generates individual frequencies which can be combined by means of harmonic drawbars to produce any desired tone quality. The block diagrams in Figures 8 thru 11 show the chief components of the instruments.
,
.
Electrical impulses of various frequencies are produced in the "tone generator'^ which contains a number of "tone wheels" driven at predetermined speeds by a motor and gear arrangement. Each tone wheel is a steel disc similar to a gear^ with high and low spots, or teeth, on its edge (see figure 12). As the wheel rotates these teeth pass near a permanent magnet, and the resulring variations in the magnetic field induce a voltage in a coil wound on the magnet. This small voltage, when suitably filtered, produces one note of the musical scale, its pitch or frequency depending on the number of teeth passing the magnet each
second.
A note played on either manual of the organ consists of a fundamental pitch and a number of harmonics, or multiples of the fundamental frequency. The fundament al and eight harmonics available on each playing key are controllable by means of drawbars. By suitable adjustment of these controls the player may vary the tone colors at will. The M-lOO Console has several preset tabs which make several pre-selected tones available,
MODEL M
Mixed tones from the manuals are amplified and then pass through the vibrato mechanism, the expression control, and additional stages of amplification before reaching the loudspeaker
-
MODEL M-2i M-3i M-lOO Mixed tones from either the upper or the lower manual may go through either the "vibrato" channel or the "No Vibrato" channel, depending on the position of the corresponding vibrato selector of "Vibrato Cancel" tabs. (The upper manual is called "Solo" on the selector tab of the M-2 and M-3 to indicate that it is best suited for playing melody or solo parts of the music.) The tones are then combined and passed through the expression control and additional stages of amplification before reaching the speaker(s)-
MODEL M-3 M-lOO

Percussion tones are produced by borrowing a signal from the upper manual 2nd harmonic drawbar, 3rd harmonic drawbar, or both, amplifying it, returning part of the signal to the same drawbar, and conducting the balance of the signal through push-pull control tubes where its decay characteristics are controlled. The percussion signal is then combined with the signal from the manuals after the vibrato system but before the expression control. The control tubes are keyed through the 6th harmonic key contacts and bus bar.
The pedal tones do not require drawbars for tone color variation, because they are produced as complex tones by special tone wheels. From the pedals these tones go to a pedal amplifier, where the attack and decay characteristics are controlled. The single pedal drawbar adjusts the volume of the pedals relative to that of the manuals, and the pedal signal than is combined with the signal from the manual before passing through the expression control, but after the vibrato system.
CONSTRUCTION AND OPERATION OF COMPONENTS

In reviewing this section refer to the schematic circuits of the entire organ systems in the back of this manual. Connections between components are shown in the wiring diagrams and control assembly wiring drawings, also in the back of the
manual,
MOTORS AND POWER SWITCHES The tone generator assembly in which all tones of the organ originate, is driven at constant speed by a synchronous motor, located at the left side as you look in at the back of the Console. Attached to it is the vibrato scanner. As the synchronous motor is not self-starting, it must be brought up to speed by a starting motor at the opposite end of the generator. The procedure for turning on the organ is as follows: Push the "start'' switch up (M-3, M-lOO) or in (M, M-2) and hold it for approximately eight seconds. This allows time for the starting motor to bring the generator up to slightly above it synchronous speed- While still holding the "start" switch, push the "run" switch upward to its "on" position. This turns on the synchronous motor and at the same time introduc,es a resistor in series with the starting motor to reduce its powerHold the "start" switch about four seconds longer and then release it-
During this time the braking action of the synchronous motor, together with the reduction in power of the starting motor, brings the system to synchronous speed so that the synchronous motor can carry the load.
To turn off the. organ, push the "run" switch downward to the "off" position.
a
TONE GENERATOR All tones of the organ originate as electrical signals in the tone generator assembly. The M, M-2 and M-3 contains 85 tone wheels while the M-lOO has 87, Each of these wheels has various numbers of teeth, with suitable gears for driving them at various speeds from a main shaft extending along the center. Each pair of tone wheels is mounted on a shaft and between them is a bakelite gear held between two coil springs, forming a mechanical vibration filter. As the gear is not rigidly attached to the shaft, any pair of wheels which may be stopped accidentally will not interfere with the operation of the others.
Adjacent to each tone wheel is a magnetized rod with a pick-up coil wound on it. These magnets extend through the front and back of the generator, and are held by set screws which can be loosened in case adjustment is ever necessary. Figure 13 shows where to find the magnet for any frequency number. In this drawing the dotted lines indicate frequencies whose tone wheels are on the
same shaft.
On top of the tone generator assembly are small transformers and condensers forming tuned filters for the higher frequencies. They are not likely to need replacing. In case one filter becomes inoperative, both the transformers and condenser must be replaced with a matched set from the factory. Figures 14, 15 16 and 17 show the locations of these filters on the indicated models. A few frequencies use untuned filters consisting of coils alone.
The output frequencies of the tone generator are numbered for convenience, in order of increasing frequency. The lowest, number 1 is about 32 cycles per second, and the highest, number 91, is about 6000 cycles per second. Frequency numbers 1 to 12 (1 to 13 on M-lOO) are used for pedals; numbers 13 to 17 (14 to 17 on M-lOO) are omitted; and numbers 18 to 91 are used for the manuals.
, ,
In case any generator frequency is weak or absent, refer to "Practical Service Suggestions" for the procedure to be used in locating and correcting the trouble.
The output terminals of the generator consist of solder lugs mounted on the filThe freter transformers, to which the manual cable and pedals are connected* quency numbers of all terminals are indicated in Figures 14, 15, 16 and 17.
MANUALS Musical frequencies from the tone generator go through the manual cable to terminal strips on the two manuals and from them to the key contact springsEach of the two manuals has forty-four (44) playing keys, or approximately 3-1/2 octaves. The two manuals do not cover exactly the same pitch range, but they are arranged so that keys of like pitch are in line. Middle "C" is the first C on the upper manual and the key in line with it on the lower manual.
Under each key are a number of contact springs (for the fundamental and harmonics of that key) which touch an equal number of busbars when the key is pressed, (Some keys at the right end of each manual have fewer springs, as noted below) All contact springs and busbars have precious metal contact surfaces to avoid corrosion, and the manuals are sealed to exclude dust so far as possible. In case a contact becomes dirty in spite of these precautions, a busbar shifter (shown in Figures 3, 5,7) is provided in each manual to slide the busbars endwise and thus provide a fresh contact surface.
-
The busbar shifting mechanism is somewhat different on the M-lOO than on prior models of the Hammond Orgam Models M, M-2 and M-3. Looking under the lower manual on the left hand end, a black wood end block will be observed. One half inch from the front of this block is a drilled hole. Within this drilling is a small metal tongue with a punched hole. Using either long nose pliers or a hook, this tongue can be moved in and out and it in turn moves the busbars. The upper manual shifter is in a similar place, but requires removal of the generator dust cover to gain access to it. The key contacts are connected through resistance wires to the manual terminal strips. The manual wiring chart Figure 18, shows how the contact of each key are connected to the proper frequencies to supply the fundamental and harmonics of that particular key. The blank spaces indicate that no key contact is used, inasmuch as the highest harmonics of the highest keys are above the range of the tone generator and are not required. Since the percussion control tubes in the M-3 and M-lOO are keyed through the 6th harmonic busbar, the blank spaces in this row have contacts connected to ground through resistance wires.
The busbars of each manual, each one carrying a certain harmonic, are wired to the harmonic drawbars for that manual in the M, M-2, M-3 and through the "Drawbars" tab in the M-IOO-
HARMONIC DRAWBARS The left group of eight (8) harmonic drawbars (Figure 19) is associated with the lower manual, and the right group of nine (9) drawbars controls the upper manual. By sliding these drawbars in and out, the organist is able to mix the fundamen^ tal and harmonics (or overtones) in various porportions. The distance a bar is pulled out determines the strength of the corresponding harmonic; and if a drawbar is set all the way in, the harmonic it represents is not present in the mixture. Neither manual will play unless at least one of its drawbars is pulled out at least part of the way in the case of the M, M-2, M-3, or with the "Drawbars^' tab pressed or preset tab pressed in the M-100.
The drawbars slide over nine (9) busbars representing intensity levels, and each drawbar has two contacts connected together by a one ohm resistor. As the drawbar moves, at least one of the contacts is touching some busbar at all times, and therefore there is no "dead spot" in the drawbar motion. The one ohm resistor avoids an actual short circuit between adjacent busbars. These busbars extend the length of the drawbar assembly but are split in the middle to form two groups of nine (9)Those in the left group, under the lower manual draw* bars, are connected to low impedance primary taps on the lower manual matching transformer. Similarly, those in the right group, under the upper manual drawbars, are connected to taps on the upper manual matching transformerSignals from the high impedance secondaries of these two transformers go through the lower manual "Vibrato Cancel" and upper manual "Vibrato Cancel" tabs to the apraplif ier input terminals
,
-
PEDAL DRAWBAR
The 12 (M, M-2, M-3) or 13 (M-100) playing pedals are operated by the left foot and are connected to the lowest 12 or 13 frequencies of the generator. The center drawbar adjusts the volume of the pedals. It operates a variable condenser (shown in Figures 3, 5, and 7) which is connected to the pedal section of the amplifier. For operation of the circuit see description of "amplifier,"
PEDAL KEYBOARD The 13 playing pedals are operated by the left foot and are connected to the Like the manuals, they have light and lowest 13 frequencies of the generator. dark keys arranged in the standard octave pattern. Figures 20 and 21 identifies the pedals and shows the generator frequency number associated with each.
A "pedal contact" on each pedal opens when the pedal is pressed, thereby allowIn addition there is ing the correct generator frequency to reach the amplifier. a "pedal keying contact'' for all pedals, which closes when any pedal is operated. It serves to key the pedal amplifier, causing the note to sound at the desired
rate-
When a pedal is pressed its "pedal contact" opens first, selecting the correct note. Immediately the "pedal keying contact" closes, causing the note to sound. When the pedal is released a mechanical latch keeps the "pedal contact" open, so that the last-played pedal note continues to sound for a length of time determined by the position of the pedal "Fast Decay" and "Pedal Legato" tabs in the M-100. In the M, M-2, and M-3; the time which the pedal sound is heard is determined by the setting of the "Pedal Decay" tablet and a "Pedal sustaining control" attached to the expression control. The electrical operation of these circuits is described under "amplifier"-
EXPRESSION PEDAL The "expression" pedal, sometimes called "swell" pedal (Figures 1 2, 4, and 6) is operated by the player's right foot and varies the volume of both manuals and pedals together. It is connected mechanically to a special variable air condenser mounted on the amplifier. When the pedal is tilted back (closed) by pushing on the player's heel the music is softest, and when pushed forward (opened) by Che player's toe the music is loudest,
In the M, M-2, and M-3, attached to the expression pedal is a "pedal sustaining control" lever, which is operated by sliding the foot sldewlse on the pedal. If this lever is not pressed, each pedal note dies away rapidly or slowly, depending on the setting of the "pedal decay" tablet. If the lever is pressed to the left, the last-played pedal note dies away much more slowly,
CONTROL TABLETS The Model M has 6, while the M-2 and M-3 have 7 of these control tablets and each has two positions (figures 1, 2 and 4). The "volume" tablet changes the overall volume and thus supplements the expression pedal. The "pedal attack" tablet determines how fast a pedal note sounds after a pedal is depressed, and "pedal decay" determines how fast the sound dies away after the pedal is released.
The "vibrato lower manual" and "vibrato solo manual" tablets turn the vibrato effect on and off independently on the lower and upper manuals respectively. The next tablet provides a choice of "normal vibrato" or "vibrato chorus" (it is effective only when the vibrato effect is on). The last tablet can be set for "small" or "normal" vibrato to adjust the extent of the pitch variation provided by the vibrato mechanism, The M-lOO has 24 tabs, each providing some change in the instruments operation. To have the instrument sound after turning it on, tabs such as "Full Organ" and "Ensemble" will place the upper and lower manual in operation. A tab is in use when in the down position. Functions of the various tabs from left to right as they appear on the instrument are given in the following paragraphs.
PERCUSSION CONTROL TABLETS The M-3 and the M-lOO are the only two Models which contain percussion and each unit has four (4) associated tabs.
In the M-lOO, these tabs operate only when the upper manual "Drawbars" tab is pressed. Pressing either "Second Harmonic" or "Third Harmonic" will, when the Upper manual is played, cause the tone to sound percussively (in addition to sustained organ tones). Both tabs can be pressed, giving a combination percussive tone, "Fast Decay" causes the percussive tones to fade away with greater rapidity"Percussion Soft" reduces the volume for the percussive signal.
In the M-3, when the "Percussion" on-off tablet is "On", the Solo (Upper) manual will play 2nd or 3rd harmonic tones percussively (in addition to the sustained organ tones). The "Volume" tablet in "Normal" position allows the per cussion tones to soilnd percussively as with the M-lOO and reduces the level of the Solo manual sustained organ tones to maintain proper balance between the manuals. In "Soft" position it allows the percussion tones to sound only softly and restores the full level of the Solo manual sustained organ
The "Decay" tablet determines how fast the percussion tones fade away when the Solo manual key is pressed.
tones.
10
Operation of the electrical circuits associated with the percussion feature are described in the percussion section of the amplifier theory.
VIBRATO TABLETS The Model M vibrato uses three control tabs- Two degrees of vibrato are available with the "amount of Vibrato" tablet and the "Vibrato Chorus". A third tablet marked "Vibrato" turns the effect on or off.
The M-'2, M-3, and M-lOO have a selective vibrato system, using four (4) control tablets to vary the vibrato effect. On the M-lOO series only, an additional stop (Vibrato Cancel) to the right of the preset tabs permits any Vibrato effect to be cancelled immediately.
The vibrato effect is created by a periodic raising and lowering of pitch, and thus is fundamentally different from a tremolo, or loudness variation. It is comparable to the effect produced when a violinist moves his finger back and forth on a string while playing, varying the frequency while maintaining constant volume.
The Hammond Vibrato equipment (See Fundamental Diagram of Vibrato System, Figures 22, 25,26) varies the frequency of all tones (excepting the pedal and percussive tones) by continuously shifting their phase. It includes a phase shift network or electrical time delay line, composed of a number of low pass filter sections, and a capacity type pickup or scanner, which is motor driven so that it scans back and forth along the line.
Electrical waves fed into the line are shifted in phase by each line section (the amount per section being proportional to frequency), so that at any tap of the line the phase is retarded relative to the previous tap
The scanning pickup traveling along the line will thus encounter waves increas^ ingly retarded in phase at each successive tap. As a shift in phase is equivalent to an instantaneous change in frequency, the continuous change in phase becomes a continuous frequency variation. Since the scanner sweeps from start to end of the line and then back, it alternately raises and lowers the output frequency, the average remaining equal to the input frequency. The exact amount of frequency shift depends not only on the amount of phase shift in the line but also on the scanning rate. This rate, however, is constant because the scanner is driven by the synchronous running motor of the organ.
In the M, M-2, and M-3, the "Amount of Vibrato" tablet varies the amount of frequency shift by causing the whole line to be scanned for "Normal Vibrato" and only one fourth of it for "Small Vibrato".
In the M-lOO, the "Vibrato Small" Tablet varies the amount of frequency shift by causing two thirds of the line to be scanned, in contrast to the entire line when in the up position. A vibrato chorus effect, similar to the effect of two or three slightly out-oftune frequencies mixed together, is obtained when the vibrato output signal is mixed with a portion of signal without vibrato. This is accomplished by the "Vibrato Chorus" tab, which causes only part of the Incoming signal to appear across the vibrato line and the rest across a resistor in series with the lineAs the vibrato effect is applied to the part of the signal appearing across the line but not to the part appearing across the resistor, the combination produces a chorus effect
-
11
In the M-lOO, a Celeste effect is obtainable by the use ''Vibrato Celeste I" and "Vibrato Celeste II" tabs. These can be used independently or together. Use of these tabs introduces a resistor network at the far end of the Vibrato line, changing the termination impedance. This in turn causes a reflective signal to appear in the line, which is picked up by the scanner. In the Model M, to remove the vibrato effect entirely, the 'Vibrato" tablet in "off" position places a very large resistor in series with the vibrato line. Practically all of the signal appears across this resistor and the vibrato effect is virtually eliminated. A compensation circuit consisting of Rl and CI maintains constant volume by introducing negative feedback with the "vibrato" tablet "off". (See Figures 23 and 24).
Figures 23 thru 26 show only the "Vibrato" channel of the amplifier. All tones sent through this channel have the vibrato effect. In the M-lOO, when vibrato is not desired on one manual or both, the "Vibrato Cancel" tabs in the down position feed their signals through the "no Vibrato" channel of the amplifier. Figures 27, 28 and 29 show the vibrato line box. location of line box.
See figures 3, 5, and
7
for
The scanner is mounted on the synchronous motor and driven at 412 revolutions per minuteIt is a multi-pole variable condenser with 16 sets of stationary plates and a rotor whose plates mesh with the stationary ones. Figure 30 shows the construction of the scanner with two sets of plates removed to show the rotor,
Signals coming from the vibrato line appear on the stationary plates and are picked up, one at a time, by the rotor. Connection to the rotor is made by carbon brushes as shown in Figure 30. Two brushes touch the sides of the contact pin and a third presses on the end, in order to eliminate the possibility of contact failure.
The complete electrical circuit of the vibrato system is shown in the schematic diagrams contained in the back of this manual-
PRESET TABS CM- 00) Four tabs are provided for each manual. As indicated, they provide a choice of using the drawbars or playing the preset tones indicated on them.
1
REVERBERATION AND VOLUME SOFT TABS CM- 00) Several degrees of reverberation are obtained by the use of either or both tabs labeled ''Reverberation I" and "Reverberation II", These tabs in addition to turning this feature on, govern the loudness or amount of reverberation by a resistive network used in conjunction with the speaker. The "Volume Soft" tab controls the overall volume of the organ and is especially useful where playing might disturb others
1
AMPLIFIER ASSEMBLY In the M and M-2 models, the amplifier assembly is on a single chassis, but is actually composed of four sections: Manual, Pedal, Intermediate, and Output as indicated in the block diagrams, figures 8 and 9, and in the schematics in the schematic section of this manual.
,
12
In the M-3 and M-lOO models there is one additional section, the percussion amplifier. The block diagrams appear in Figures 10 and 11,
The M-lOO model alone has one additional amplifier assembly, the Reverberation Amplifier. This separate amplifier is used to secure the Reverberation effect This amplifier has its own speaker, in conjunction with the Reverberation unit.
MANUAL SECTION OF AMPLIFIER MODEL M The manual section, composed of tubes VI and VZ, receives its signal from the matching transformer Tl. The "special input" jack, connected through a net-work to the cathode of VI, provides a low impedance input circuit (see "Special Equipment")* Some treble attenuation is provided by a feedback network con^ sisting of C2, R2, and R3, connected from cathode follower tube V2 to the input of VI, The output signal obtained from the cathode of V2 drives the vibrato line (see "Vibrato system") and the manual signal, after passing through the vibrato system, is combined with the pedal signal at the grid of V3.
MODEL M-2 M-3 is composed of two channels connected to the "Vibrato" and terminals. Either of the two matching transformers can either input channel, depending on whether the correspondis set for Vibrato "on" or "off".
The manual section "no Vibrato" input feed a signal into ing control tablet
Signals entering the "no Vibrato" channel (tube V2) are amplified and fed directly into the intermediate section of the amplifier while signals going into the "Vibrato" channel (tubes VI and V3) pass through the Vibrato system firstThe output signal of the Vibrato system is combined with the "no Vibrato", Percussion^ and Pedal signals at the grid of the intermediate amplifier.
Suitable tonal balance is secured in the "no Vibrato" channel by a feedback network connected from plate to grid of V2. Similar tonal balance is provided in the "Vibrato" channel by a feedback network connected from cathode follower V3 to the gird of VIThe two channels are matched by selecting R27 (M-3), and R20 (M-2) at the factory-
M-100 The manual section is composed of two channels connected to the "Vibrato" and "no Vibrato" input terminalsEither of the two matching transformers can feed a signal into either input channel, depending on whether the corresponding control tablet is set for vibrato "on" or "off".
Signals entering the "no Vibrato" channel (tube V2) are amplified and fed directly into the intermediate section of the amplifier, while signals going into the "Vibrato" channel (tubes VI and V3) pass through the Vibrato system first. The output signal of the Vibrato system is combined with the "no Vibrato" and pedal signals at the grid of the intermediate amplifier.
Suitable tonal balance is secured in the "no Vibrato" channel by a feedback network consisting of C6, R12, R13 and R13A connected from plate to grid of V2. Similar tonal balance is provided in the "Vibrato" channel by a feedback network including CI, Rl, R2, and R2A connected from cathode follower V3 to the input The two channels are matched by selecting R20 at the factory. of VI.
13
PEDAL SECTION OF AMPLIFIER - Mi M-2i M-3 The pedal amplifier, composed of one tube, V7, receives its signal directly from the pedal generators. When a pedal key is pressed its "pedal contact" opens, delivering a signal voltage of the proper frequency to the grid of V7, The note cannot sound instanly, however, because the tube is normally cut off by a negative 21 volt grid bias.
Near the end of the pedal stroke the "pedal keying contact" (common to all pedals) closes. This shunts a resistance from the bias point to ground, discharging the bias condenser C57 and allowing the note to sound.
If "pedal attack" is at "normal" only a single resistor R68 is placed across
the bias condenser when the pedal keying contact closes. This very quickly discharges the condenser, and the note sounds quickly, although not abruptly.
In case "pedal attack" is set at "slow"^ the shunting resistor is increased by the addition of R69 and so the bias condenser cannot discharge as quicklyIt takes an appreciable time, therefore, for the bias to drop low enough so that the note sounds
When the pedal key is released, the pedal keying contact opens, allowing cutoff bias to be applied again to the tube. With "pedal decay" set at "fast" this occurs rapidly, since R74 charges C57 in a short time. With "pedal decay" set at "normal" the increased resistance delays the charging of C57 and permits the tone to sound for a longer time.
If the "pedal sustaining control" is operated (lever on expression pedal pressed to left), an additional resistor R76 is introduced. This delays the charging of C57 still further and causes the note to sound for a much longer time.
A latching mechanism holds the last-played pedal contact open until some other pedal is operated, in order to Insure that the correct note will sound throughout the decay period.
The pedal cutoff adjustment R73 varies the screen voltage of the pedal amplifier tube. It must be adjusted so that the pedal tone is just inaudible with the pedal drawbar and expression pedal set in loudest position, as instructed in "Practical Service Suggestions".
M-lOO
The pedal amplifier, composed of one tube, VIO, receives its signal directly from the pedal generatorsWhen a pedal key is pressed its "pedal cqntact" opens, delivering a signal voltage of the proper frequency to the grid of VIO.
+
The note cannot sound instantly, however, because the tube is normally cut off by a negative 22 volt grid bias.
+
Near the end of the pedal stroke the "pedal keying contact" (common to all pedals) closes. This shunts a resistance from that bias point to ground, dis charging the bias condenser C57 and allowing the note to sound. When the pedal key is released, the pedal keying contact opens, allowing cutoff bias to be applied again to the tube. With the pedal "Fast Decay" tab depressed this occurs rapidly, since R81 charges C57 in a short time. With the tab up, the increase resistance delays the charging of C57 and permits the tone to sound for a longer time.
14
"
If the "Pedal Legato" stop Is depressed, an additional resistor R82 is introduced. This delays the charging of C57 still further and causes the note to sound for a
much longer time.
A latching mechanism holds the last-played pedal contact open until some other pedal is operated, in order to insure that the correct note will sound throughout the decay period.
The "Bass Mute" tab varies a filtering circuit in the VIO tube output so the higher frequencies are bypassed to ground, giving a deeper tone to the pedals. The pedal cutoff adjustment R85 varies Che bias voltage of the pedal amplifier tube. It must be adjusted so that the pedal tone is just inuadible with the pedal drawbar and expression pedal set in loudest position, as instructed in "PracticalService Suggestions.
To prevent a pedal note from sounding when the organ is first turned on, a resistance of five ohms inserted in series with the heater of the pedal amplifier tube lengthens its warm-up time so that the cutoff bias is applied before the tube is conductive.
INTERMEDIATE SECTION OF AMPLIFIER
From the plate of the pedal amplifier tube the pedal signal passes through a variable air condenser (operated by the pedal drawbar) to the intermediate amplifier (half of V3)(M), V4 (M-2, M-3, M-lOO) At this point the pedal signal is mixed with the vibrato, non-vibrato, and percussion signals from the manuals (M-3, M-lOO).
.
Depressing the "Volume Soft" tab reduces the overall volume of both manuals and pedals by shunting a small condenser across the input of the intermediate amplifier. At the same time it provides pedal compensation by adding R65 in series with the pedal generators and thereby increasing the relative volume
of the pedals-
The small feedback condenser from plate to grid of the intermediate amplifier is a means of increasing the effective input capacity of the tube. In this circuit the effective input capacity is this value multiplied by the amplification factor of the tube, or a total of about 1500 micromicrof arads This provides a suitable load for the output of the scanner and the pedal drawbar,
,
The combined manual and pedal signals go through the intermediate amplifier to the expression control (operated by the expression pedal), which is a special variable air condenser with a single set of movable plates and two sets of stationary plates. With the expression pedal in "loud" position the signal is transitted directly to the grid of the following tube, while in "soft" position the signal goes through a tone^compensated attenuating network. At intermediate positions the signal is obtained from both sources, providing continuously variable control,
OUTPUT SECTION QF AMPLIFIER (M) V4 is a common-cathode-impedance phase inverter driving push-pull output tubes V5 and V6* The second grid of V4 provides a radio-phonograph input channel (see "Special Equipment"). A small feedback condenser from voice coil to grid of V4 makes the pedal response more uniform by reducing speaker resonance. (In model M consoles below serial number 3000, with amplifiers marked type M-A, this feedback connection is not used; C46 is omitted, C37 is omitted, C42 is .00135 mfd,, 15
and T2 does not have a secondary center tap)

M-2i M-3
The second half of V3 is a phase inverter driving push-pull output tubes V5 and V6. A small feedback condenser C22 Cm-2), C23 (M-3) from voice coil to grid of V4 makes the pedal response more uniform by reducing speaker resonance. This condenser (located in the expression control unit) is variable and is adjusted at the factory.
M-lOO
The second half of V3 is a phase inverted driving push-pull input tubes V5 and V6, which in turn drive two 16 ohm speakers connected in parallel, A small feedback condenser C23 from output transformer secondary to grid of V4 makes the pedal response more uniform by reducing speaker resonance. This condenser (located in the expression control unit) is variable and is adjusted at the factory.
PERCUSSION SECTION OF AMPLIFIER The 2nd or 3rd harmonic signal (M-3) or both (M-lOO) (depending on position of the harmonic selector tabs) is conducted through the percussion matching transformer and amplified by tube V7. The resistive feedback on this tube provides proper loading on the matching transformer to fix the primary impedance at about 5 ohms. This provides a volume compensating effect so that the percussion output signal is about the same whether one key or several are played. Besides providing push-pull signal for the control tube (V9), transformer T5 has another winding which feeds signal to the 2nd or 3rd harmonic drawbar through equivalent key circuit resistors.
"^
The control tube (V9) is normally conducting, so when a key is pressed the second or third harmonic percussion signal first sounds loudly. It passes through the control tube, transformer T6, a band pass filter network, and terminal D to the grid of V4,
Imrr.ediately the note begins to fade away, giving the characteristic percussion effect. This fading Is accomplished as follows: When the percussion switch is "on'', terminal K (normally held at plus 25 volts through anti-spark resistor (R-53) is connected to the solo manual 6th, (8th in M-3) harmonic busbar* When a key is pressed, terminal K is grounded through the key contact and the tone gen-
erator filter. This virtually grounds the plate of V8 (connected as a diode), open-circuiting the tube and isolating the control tube grid circuit. The grids then drift from their operating potential of about plus 25 volts to a cut-off potential (about plus 15 volts) at a rate determined by the time required for 031 to discharge through R59 and R60The percussion signal is now blocked. No percussion notes can sound until all keys of the solo manual are released and the control grids again rise to plus 25 volts. The time of this rise (that is, how quickly the control tubes turn on again after a key is released) is the time required to change C31 to plus 25 volts through R57 and R58.
16
When the percussion Second Harmonic" or Third Harmonic" (>i-3) or both (M-lOO) tabs are down, the corresponding upper manual harmonic drawbars are disconnected from their lead wires and these wires (which come from the manual busbars) are connected to the percussion matching transformer. The 6th harmonic (M^lOO) or 8th (M^3) drawbar is also disconnected from its lead wire and this wire (which is grounded through the generator magnets when any key is pressed) is used to turn off the push-pull control tube. Therefore, the 6th harmonic (M-lOO) or 8th (M-3) is not available on the upper manual when the percussion is in use.
When the "Percussion Soft" tab is depressed, it reduces the volume by shunting resistor R50 across the percussion output transformer.
The percussion "Fast Decay" tab determines how fast the sound fades away after a k-ey is pressed. When a key is pressed with the tab up, resistor R60 discharges capacitor C31, reducing the D,C. voltage on the control tube grids to cutoff in about 2-1/2 seconds. When the tab is pushed down another resistor is shunted across the original resistor R60, reducing the time to discharge capacitor C31 and thereby reducing the D.C. voltage on the control tube grids to cutoff in less than 1/2 second. To preserve about the same effective loudness between "slow" and "fast" decay settings, shunt resistor R62 is disconnected when the decay tab is in "fast" position. This reduces the effective control tube bias and thus increases the loudness.
With the "Second Harmonic" tab depressed, the upper manual 2nd harmonic drawbar wire is connected to the percussion matching transformer and a signal is fed back to the 2nd harmonic drawbarWith the "Third Harmonic" tab depressed the upper manual 3rd harmonic drawbar wire is connected to the percussion matching transformer and a signal is fed back to the 3rd harmonic drawbar. Both tabs can be used at the same time in the M-lOO, however in the M-3, only one or the other is available.
POWER SUPPLY (ALL MODELS) The power supply uses a 5U4 rectifier tube with a conventional filter circuit.
TUBE SOCKET VOLTAGES Voltages shown on the schematics are taken with a 20,000 ohm-per-volt meter. Line variations may cause up to 20% variation in the indicated voltages.
To make tube sockets accessible, remove lever from shaft of expression unit on amplifier; loosen cable clamp on lower shelf; remove four amplifier mounting screws and turn amplifier upside down, being careful not to rest on expression unit lever. The tabs and expression lever may be in any position, and no key should be depressed unless specified,
REVERBERATION AMPLIFIER (M-lOO) When either "Reverberation I," "Reverberation II," or both are used, the music played will be reverberated. This reverberation signal is in addition to the normal sound produced through the two 12" speakers connected to the main ampli^ f ier A separate amplifier and speaker are incorporated in the instrument for this purpose,
A signal from the voice coil terminals of the regular speakers in the console goes through a resistor network and two Incandescent lamps to the drive coils of the reverberation unit, as shown under "input to reverberation unit" in the s chema tic d ia g ram
17
The incandescent lamps are used as volume limlters or volume compression circuit. When the organ is played loudly, the lamp filaments become hot and Increase in resistance, and, therefore, the amount of signal furnished to Che reverberation unit does not increase as fast as the volume of the no-reverberated signal. This is a desirable musical effect, since a greater proportion of reverberated signal is needed at low volume levels. The drive coils introduce vibration in two coil springs. These vibrations bounce hack and forth in the coils springs to simulate natural echoes of sound, in a large room. Pickup coils at the other end of the two springs drive the input of the amplifier. The amplifier output drives an 8 ohm 8" speaker.
SPECIAL EaUIPMENT
RADIO. PHONOGRAPH. OR MICROPHONE A phonograph, radio, or microphone amplifier will play through the organ speaker if connected to the pin jack marked "RADIO-PHONO" located on the expression control unit of the organ amplifier. The device should have an output level of about 1/2 volt maximum, and must have its own volume control, as neither the expression pedal nor the "Volume" tablet will affect it. The organ may be played at the same time.
In the Model M only, occasionally for special effects it may be desirable to apply vibrato to the signal from a phonograph, radio or microphone. In this case connect to the pin jack market "SPEC-INPUT". This point has a low impedance to ground (about 7000 ohms) and may conveniently be driven from the voice coll terminals of an amplifier having a level of about 5 volts maximum. The expression pedal, "volume" tablet, and three vibrato tablets will then be effective on the input signal just as they are on the organ music.
EXTENSION SPEAKER An additional speaker, of the permanent magnet dynamic type, may be attached to the organ if special circumstances make it desirable. It should be connected to the two voice coil terminals on the amplifier. It is essential that the speaker be at least 10" in diameter and be mounted in an adequate baffle to bring out the organ pedal notes properly. The console speaker voice coil wires may be left connected or not, as desired.
Hammond Organ tone cabinets may be used as extension speakers. ing the necessary connections can be secured from your dealer.
A kit for mak-
EAR PHONE (MONAURAL) Ear phones may be connected to the organ if someone wishes to practice without disturbing others. They will generally give adequate volume when connected to the^ voice coil" terminals of the amplifier, with the speaker disconnected. A resistor of 6 to ID ohms, with power rating not less than 10 watts must be connected across these terminals whenever the speaker is disconnected.
18
EAR PHONE (STEREO) Stereo ear phones can give pleasing results when attached as shown in the schmatic below. A separate two pole double throw switch is required in addition to the listed resistors and jack. Use of good quality ear phones made by David Clark, Koss, or Telex are recommended and can be secured from any parts supply house.
GN.
T^J
Organ Spk, wires
100 -a
BLK,
CN,
:-3
Rev, Spk. wires
10
jo.
10 W
BLK-
SPECIAL POWER SOURCES The organ must always be connected to an alternating current source of the voltage and frequency specified on the name plate. If the only available power source is direct current or has a frequency different from that specified, it will be necessary to provide a converter or motor generator of at least 170 watts capacity.
PRACTICAL SERVICE SUGGESTIONS

ORGAN DOES NOT PLAY (a) If the starting motor does not operate when the "Start" switch is pressed and If the tubes do not light with the'^Run'' switch on, check the power wiring, power switch, line cord, line cord plug, and wall outlet.
(b)
If the generator turns and the tubes light, but no sound can be obtained with all controls in playing position, the most likely source of trouble is the amplifier. In most respects this is a conventional amplifier circuit, and the schematic diagrams will enable the service man to lo-
cate the trouble.
ONE KEY DOES NOT PLAY OR A HARMONIC IS MISSING (Tests to be made with "Drawbars" tab depressed) This may mean a dirty key contact, a broken connection, or a dead note in the generator. The steps below will serve to isolate the trouble(a) Ordinarily only one of the several frequencies used on the key will be missing. This can be determined by holding the key and operating each drawbar for that manual, observing on which drawbar the key falls to play Reference to the manual wiring chart, figure 18 will tell which frequency number is missing. (b) See whether the same frequency is missing where it is used on other keys of the same manual. The wiring chart will tell with what other key and
19
(c)
what other drawbar you should get the same frequency. If It is missing In some on one key but not on others, a key contact is probably dirty. cases it may be cleared by striking the key 15 or 20 times in a rapid If this procedure is not effective, staccato manner to loosen the dirt. (See adjustment of the busbar shifter for that manual will clear it, "manuals" section on a prior page for location and manner of adjustment). This will slide the busbars endwise so they present a clean contact surface. In extreme cases, it may be necessary to hold down the faulty key while making the adjustment, If the frequency is missing on all keys of one manual but not on the other manual, look for a break in the cable connecting one manual to the other.
If the frequency is missing on both manuals, check the manual-to-generator cable or the generator itself. The output of any signal frequency on the tone generator may be checked by pulling out any drawbar and connecting a clip lead from the back end of the drawbar to the generator terminal in question. See Figures 14, If the generator 15, and 16 for location of all generator terminals. Is all right, the note will play loudly. CAUTION; Never test the tone generator with an outside source of current such as a continuity meter, as serious damage may result to the sensitive filter transformers and permanent magnets. By the above method, all necessary tests of the tone generator may be made with the current sup^ plied by the generator itself. If it fails to play, try touching the clip to the input side of the filter coil (not the grounded tap) and the input side of the filter condenser (Figures 14, 15 and 16) in order to check these parts. Disconnect the If condenser to eliminate the possibility of a grounded transformer the signal is still missing at the magnet coil terminal, it means that the tone wheel is not turnings the coil is defective, or the magnet is
.
(d) (e)
(f)
(g)
(h)
(i)
not properly adjusted. If the tone wheel is not turning^ the frequency of the other wheel on the same shaft will also be missing (with the exception of a few wheels which are alone). On the generator magnet location drawing (Figure 13), the two frequencies whose numbers are connected by a dotted line are on the same shaft. Antoher way to check the wheel is to raise the generator slightly and feel the wheel with your finger to see if it is turning. Each wheel is located directly behind its magnet, shown in Figure 13. If the magnet coil is defective, the generator must be returned to the factory, as replacement of a coil necessitates dismantling the entire generator, It is possible, although unlikely, that the magnet may have become loose It may and moved so far from the wheel as to make the not inaudible. be adjusted as described in the following paragraph.
ONE NOTE IS WEAK (a) Trace the note as described in the preceding section to see whether weakness is due to dirty contact, poor connection, defective filter or reduced output of magnet coil. Check at each point by comparing intensities with higher and lower frequency numbers. (b) It is possible that one or more notes may be acoustically weak, due to the room and the furnishing, although the actual signal level is equal to that of adjacent notes. This can be checked by reading voltages of the various notes on an output meter connected to the voice coil terminals on the amplifier. All notes will not give equal output, but voltage should vary smoothly In this test variations of less than 30% should be ignored from note to note.
20
(c)
Each magnet is set at the factory by tapping it gently, with the set screw partially loosened, while observing an output meter. Experience has shown that the magnets seldon need adjustment and that setting them without proper equipment involves danger of damaging both magnet and wheel. Therefore, it is not recommended that the service man attempt this adjustment.
PERCUSSION NOTES WEAKt DO NOT PLAYi OR DO NOT DECAY PROPERLY (a) Adjust percussion cutoff control; with expression pedal wide open, "Volume Soft" tab up, upper "Drawbars" tab down, all drawbars pushed in, press "Third Harmonic" and "Fast Decay" tabs. Hold down first C key on upper manual and adjust percussion cutoff control to the exact point of cutoff or silence, (b) Check tubes V7, V8, V9(c) Always adjust percussion cutoff control after replacing V9 C12AU7).
PEDAL NOTE SOUNDS AT FULL VOLUME (WHEN PEDAL IS NOT BEING PLAYED) It is possible to make a black pedal lock down and play continuously by (a) striking it very hard at an angle so that it moves sidewise as well as downward. This will never occur if the pedals are used properly, as only slight pressure with the toe is required for playing. (b) A pedal locked down in this way will remain visibly depressed and tilted. It can be released by pressing it down very hard, with a slight pressure opposite to the direction of tilt. No permanent damage will result.
PEDAL NOTE
SOUNDS FAINTLY (WHEN ORGAN IS NOT BEING PLAYED)
(a) (b) (c) (d)
In this case the pedal cutoff control may be adjusted as follows: Set expression pedal wide open, pull pedal drawbar to its loudest position, and leave three pedal tabs up. Play highest pedal key and then release it. Wait at least 15 seconds for pedal note to die away. Slowly turn pedal cutoff adjustment (on face of amplifier) clockwise until pedal note just disappears. Do not turn it any farther. Always recheck this adjustment when replacing the 6BA6 tube.
HUM
(a)
A loud 60 cycle or 120 cycle hum in the speaker may come from some nearby electrical appliance, as explained on the instruction card. It may be picked up by the matching transformer, the vibrato line, or the console wiring. Hum from this source will disappear if you ground the signal input terminals on the amplifier to the chassis. It may be eliminated by moving either the console or the appliance. The faint pedal note heard when the pedal cutoff adjustment needs setting may sometimes be mistaken for hum. Check it as described under "Pedal note sounds faintly when organ is not being played. Any other hum must originate in the amplifier circuit, and can generally be cured by replacing one or more of the electrolytic condensers. In case hum originates in the amplifier but is not due to the electrolytic condensers, its source can be isolated by successively removing tubes or by grounding successive points in the signal circuit
(b)
(c) (d)
21
REPLACING TUBES (a) The vacuum tubes are all standard radio types and can be tested in the usual way. (b) If the 6BA6 tube is replaced, check the pedal cutoff adjustment as explained under "Pedal note sounds faintly when organ is not being played", If tube V9 is replaced, check percussion cutoff adjustment as explained (c) under "Percussion notes weak, do not play, or do not decay properly".
PROCEDURE FOR REMOVING PARTS IN NEED OF REPAIR OR REPLACEMENT

TO REMOVE KEY FROM UPPER MANUAL (Mi M-2i M-3) (a) Remove music rack by unscrewing thumb screw, unhooking brace, and lifting it from console. (b) Remove music rack base by taking out two screws in upper manual end blocks, (c) Remove metal angle fastened across keyboard by two screws (d) To remove a black key loosen its key mounting screw (See Figure 3), unhook key from screw and lift out key. (e) To remove a white key loosen its key mounting screw and those of adjacent black keys. Unhook these keys from screws, push them back, and lift out white key,
M-lOO
(a) (b)
(c) (d)
(e)
(f)
Remove music panel and top. Remove four screws which secure metal cover on control panel assembly, Remove two large screws located at ends of control assembly, which secure It to upper manual. Pull out drawbar on extreme left and fold control assembly back, To remove a black key, loosen its key mounting screw (See Figure 7), unhook key from screw and lift out key. To remove a white key, loosen its key mounting screw and those of adjacent black keys. Unhook these keys from screws, push them back, and lift out white key.
TO REMOVE A KEY FROM LOWER MANUAL (Mi M-2i M'3) (a) Remove music rack by unscrewing thumb screw, unhooking brace, and lifting it from console. Remove music rack base by taking out two screws in upper manual end blocks(b) (c) Detach pedal volume control (Figure 3) by removing two machine screws, loosening wood screw which holds friction clip to top of console, and unhooking from drawbar. Remove upper manual mounting bolts "A" and "B" under keyboard (Figure 33) (d) (e) Place a 3/4" board under each upper manual chassis mounting block; this will hold up upper manual sufficiently to make lower manual key mounting screws accessible, (f) To remove a black key loosen its key mounting screw (See Figure 3), unhook key from screw and lift out key. To remove a white key loosen its key mounting screw and those of adjacent (g) black keys. Unhook these keys from screws, push them back, and lift out white key,
M-lOO
(a)
(b)
(c) (d)
Remove music panel and top Remove generator dust cover by taking out seven screws from edge of generator shelf and loosening four screws in cover just below upper manual assembly Remove upper manual mounting bolts (2) which are located at ends of console directly above front corners of generator. Remove two screws which pass through angle brackets into upper manual.
22
(e) (f) (g) (h)
mounted on inside of cheek blocks. These screws are accessible from front of organ. Tilt manual from front, being careful that It does not slip back. Using 1/4" box ratchet, loosen key mounting screw, To remove a black key, loosen its key mounting screw (see Figure 7), unhook key from screw and lift out key. To remove a white key loosen its key mounting screw and those of adjacent black keys. Unhook these keys from screws, push them back, and lift out white key.
TO REMOVE A DRAWBAR CONTACT SPRING (Mj M-2i M-3) Push drawbar all the way in(a) (b) Remove screw and nut at back end of drawbar (Figure 3). (c) Pull out contact spring while pressing with thumb to release pressure on contact. To disconnect spring entirely, unsolder wire. Do not under any circumstances pull drawbar forward while contact spring (d) is off, as damper spring will catch in slot and ne'cessitate removal of entire drawbar assembly
M-lOO
(a) (b) (c)
(d)
Remove music panel and top. Remove four screws which secure metal cover on control panel assembly, Pull out contact spring while pressing with thumb to release pressure on contact. To disconnect spring entirely, unsolder wire. Do not under any circumstances pull drawbar forward while contact spring is off, as damper spring will catch in slot and necessitate removal of entire drawbar assembly.
TO REMOVE A DRAWBAR OR DRAWBAR KNOB (Mi M-2i M-3) (a) Remove music rack by unscrewing thumb screw, unhooking brace, and lifting it from console, (b) Remove music rack base by taking out two screws in upper manual end blocks (c) Remove 8 hexagonal head machine screws holding drawbar assembly and one screw fastening angle across upper manual keys (d) To remove knob pull drawbar assembly toward front of console (be careful not to scratch control panel surface) prop it up, and remove screw which holds knob (e) To remove drawbar and contact spring, pull them out at back of assembly, while pressing with thumb to release pressure on contact. (f) To separate drawbar from contact spring remove screw and nut at back end of drawbar. M-lOO
,
,
(a)
(b) (c)
(d) (e)
(f) (g)
Remove music panel and top. Remove four screws which secure metal cover on control panel assembly. Remove two large screws located at ends of control assembly which secure It to upper manual (Pull out drawbar on extreme left) and fold back. Remove 4 hexagonal head machine screws holding drawbar assembly, To remove knob, pull drawbar assembly toward front of console (be careful not to scratch control panel surface) prop it up, and remove screw which holds knob. To remove drawbar and contact spring, pull them out at back of assembly, while pressing with thumb to release pressure on contact, To separate drawbar from contact spring remove screw and nut at back end of drawbar
,
23
TO REMOVE UPPER MANUAL (Mi M-2i M-3) Remove music rack by unscrewing thumb screw, unhooking brace, and lifting (a) it from console Remove music rack base by taking out two screws in upper manual end blocks. (b) (c) Remove dust cover over generator by taking our seven screws from edge of generator shelf and loosening four screws in cover just below upper manual assembly (d) Detach control panel by removing 6 machine screws from top of panel, and lay panel on generator, being careful not to damage generator wiring. Control panel wires need not be disconnected. (e) Detach pedal volume control (Figure 3) by removing two screws which hold it and loosening wood screw which holds friction clip to top of console; unhook control from drawbar and lay it on generator, being careful not to damage generator wiring. Volume control wires need not be disconnected, (f) Remove two screws fastening matching transformer bracket to upper manual, take off round cover held by two screws, unsolder and detach shielded wires and black wire from transformer, Re-attach matching transformer to upper manual. Cg) (h) Unsolder wires from lower manual drawbars. (i) Remove upper manual mounting bolts "A" and "B" under keyboard (Figure 33). Remove the two upper manual stop plates, held by two wood screws (Figure 3). (j ) Prop up front of upper manual so that its terminal strip is accessible. (k) Be careful when raising and lowering manual that its terminal strip is not damaged by rubbing lower manual keys Unsolder manual cable from terminal strip. Lower manual into normal position, (1) Detach vibrato line box by removing two screws in sides of box fastening it (m) to underside of console top; lay line box on top of generator, being careful not to damage wiring on generator. Line box wires need not be unsoldered (early M-3 only) (n) Where line box is of metal construction unsolder wires from scanner leaving it attached to manual. (o) Carefully lift manual assembly (including drawbars and matching transformer) out through back of console, Remove metal angle fastened across keyboard by two screws. (p) Take out 8 hexagonal head machine screws from drawbar assembly and carefully (q) lift off drawbar assembly and matching transformer assembly.
-
M-lOO
(a) (b)
(c)
(d) (e) (f) (g)
(h)
(i)
Remove music panel and top, Remove four screws which secure metal cover on control panel assembly. Remove two large screws located at ends of control assembly which secure it to upper manual. Remove generator dust cover by taking out seven screws from edge of generator shelf and loosening four screws in cover just below manual assembly, Remove two manual ho Id- down bolts located at ends of console directly above front generator corners Reinstall dust cover temporarily, Remove two screws fastening matching transformer bracket to upper manual, Detach pedal volume control by removing two screws which hold it to manual assembly. Unhook control from drawbar and lay it on generator cover. Volume control wires need not be disconnected Remove vibrato line box by taking out four screws attaching it to rear of upper manual. Remove screws holding four plastic clamps containing wiring.
"
24
, .
Cj )
(k) (1)
(m) (n)
Co)
(p)
(q)
Locate nine coded wires coming from busbars inside manual, Tehse are found at right rear of manual. Trace this troup of wires to upper manual preset tabs and unsolder. Note location and routing as shown on wiring diagram and in consoleTake out four hex head machine screws from drawbar assembly. Entire control panel, drawbar assembly, line box, pedal volume control and matching transformer can now rest on generator cover. Reinsert two bolts which held the control assembly to the manual assembly, Remove two screws which pass through angle brackets into upper manual. Prop up front of upper manual so that its terminal strip is accessible. Be careful when raising and lowering manual that its terminal strip is not damaged by rubbing lower manual keysUnsolder manual cable from terminal strip. Lower manual into normal positionCarefully lift manual assembly out of console.
t
TO REMOVE LOWER MANUAL (Mi M'2 M-3) (a) Remove music rack by unscrewing thumb screw, unhooking brace, and lifting it from console. (b) Remove music rack base by taking out two screws in upper manual end blocks. (c) Remove dust cover over generator by taking out seven screws from edge of generator shelf and loosening four screws in cover just below upper manual assembly. (d) Loosen wood screw holding friction clip of pedal volume control (Figure 3) to top of console, Remove upper manual mounting bolts "A" and "B" under keyboard. (Figure 33) Ce) (f) Prop up front of upper manual as far as possible. Be careful when raising and lowering upper manual that its terminal strip is not damaged by rugging lower manual keys. Remove two hexagonal head mounting bolts from rear end of lower manual (g) chassis mounting blocks. (h) Remove three screws X, Y, Z under keyboard (Figure 33). (i) Remove lower manual end blocks by taking out screws C, D, E, and F under keyboard (Figure 33) Unsolder manual cable wires from terminal strip, (j) (k) Lift manual out through front of console, being careful not to damage woodwork.
(a)
(b)
(c) (d)
(e)
(f) (g)
M'lOO Remove screws holding four plastic clamps containing wires, on rear of upper manual. Locate nine coded wires coming from busbars inside of lower manual- These are found at right rear of manual. Trace this group of wires to lower manual preset tabs and unsolder. Note location and routing as shown on wiring diagram and in console. Prop upper manual from front, being careful it does not slip back. Remove both lower manual end blocks, by removing two screws through manual frame and one screw through bracket in check block. Remove lower manual terminal cover, hedl by four screws under keyboard. Remove two hex bolts which secure lower manual to case. Loosen (don't r^tnove) four hex screws holding front of lower manual to
front rail of case. Lif t out lower manual
(h)
25
TO DETACH AND OPEN CONTROL PANEL (Mi M-2 M-3) (a) Remove dust cover over generator by taking out seven screws from edge of generator shelf and loosening four screws in cover just below upper manual assemblyControl tablet box may now (b) Remove six machine screws from top of panel. be lowered and pulled toward rear of console. Lay box upside down on generator (being careful not to damage wiring on (c) Care should generator) and remove bottom cover by taking out four screws. be taken not to pull the wires or cables excessively during this procedure. None of the wires or cables need be disconnected. TO DETACH
(a)
(b) (c)
OPEN PERCUSSION CONTROL SWITCH (M-3 ONLY) Remove screws C and D under keyboard (Figure 33) Remove four fastenings holding panel to wood block. Turn tablet assembly upside down and remove bottom cover by taking out two screws Wires need not be disconnected
Aâ3
.
TO REMOVE GENERATOR <Mt M-2 M-3j M-IOO) FIRST PULL OUT LINE PLUG (a) Remove dust cover over generator by taking out seven screws from edge of generator shelf and loosening four screws in cover just below upper manual assembly, (b) Unsolder, at line panel, six wires (5 wires on M, M-2, M-3) to running and starting switches (c) Unsolder, at line panel, three wires to amplifier, Unsolder pedal and manual cables from generator, (d) (e) Disconnect scanner shielded wire from amplifier terminal. (f) Unsolder cable of six green wires from scanner terminals. Unsolder scanner wires from terminals 3, 4, and 5 (12, 13, and 14 on M, (g) M^2, M-3) on vibrato line box. (h) Unsolder two black wires from generator cover near start motor end, and also grey wire (connected to junction of two carbon resistors on generator cover) (i) Remove 4 generator hold down screws (4 cotter pins from clamping screws and remove screws on M and M-2). Unhook four suspension springs from generator. (j ) (k) Carefully lift out generator.
TO REMOVE STARTING MOTOR (Mt M-2> M-3i M-lOO) FIRST PULL OUT LINE PLUG Remove dust cover over generator by taking out seven screws from edge (a) of generator shelf and loosening four screws in cover just below upper manual assembly. Remove oiling threads (tied to two motor bearings) from oil trough by (b) pulling or cutting them, (When replacing threads be sure they go under
(c)
(d) (e)
felt in trough) Provide more slack in lead wires at starting motor by pulling wires carefully, Unscrew two hexagonal studs extending beyond outer edge of motor. Lift motor out and unsolder its lead wires- (Be careful to remove and replace all threads).
TO REPLACE PILOT LIGHT (M-lOO ONLY) (a) Remove music panel and top. (b) Remove four screws which secure metal cover on control panel assembly. Lift fiber shield over bulb and replace bulb. (c) NOTE;
Use No. 12GE 6.3V
.ISA
Minature
pin.
26
TO REPLACE A BROKEN TAB CM- 100 ONLY) Remove music panel and top, (a) Remove four screws which secure metal cover on control panel assembly, (b) Remove two Phillips screws from front of control panel that hold bank (c) of switcht^s associated with tab to be replaced. Remove lock washer from either end of switch assembly, and pull rod out (d) It may be necessary to tilt assembly so so it just clears broken tabthat free end of rod will clear adjacent switch assembly, Remove remains of broken tab and insert new piece, (e)
A small bronze spring washer will be found between tab and one NOTE; Be sure this is reinserted with new tab. side of switch assembly.
TO REMOVE VIBRATO LINE BOX (Mt M-2i M-3t M-IQO) Unsolder wires from line box terminals (a) Remove two screws in bottom edge of box fastening it to underside of (b) On later units, remove four screws fastening it to rear console topof upper manual.
TO REMOVE PEDAL KEYBOARD (M, M-2i-M-3i M-lOO) Remove dust cover over generator by taking out seven screws from edge (a) of generator shelf and loosening four screws in cover just below upper manual assemblyUnsolder pedal cable from generator. (b) Remove three pedal keyboard twisted wires from amplifier terminal panel, (c) Place suitable wooden strips under pedal keyboard assembly to support (d) First remove two screws in back of console it when screws are removed. (Figure 3), and then remove three screws on lower shelf toward front of console over pedal keyboard.
NOTE:
(e)
It may be necessary to remove two speakers to take out these
latter mentioned screws. (When re-installing pedLift console and pull out keyboard and stripsal keyboard replace two screws in back of console first, leaving these screws loose until remaining screws are replaced),
TO REMOVE EXPRESSION PEDAL (M, M-2 M-3- M-lOO) Disconnect two twisted wires from "SUS SW" terminals on amplifier, (Model (a) M, M-2) terminals "W" and "X'' on M-3) Prop up right end of console at least 6 inches from floor. (b) Unhook coil spring from expression unit arm. (c) Remove screw linking expression unit on amplifier to expression pedal. (d)
.
NOTE FOR M-3 ONLY A change in all amplfiier coded ''H'' and above removes the positive voltage from This can be incorporated in earlier amplifiers the stators of the swell assemblyThe end result will place a block-condenser (,02mfdby following the steps below. This change will insure con^ 600V) between pin 1 of the 12AX7 and the swell statorstinued noise free operation of earlier amplifiers.
SEE FIGURE 36A OF SERVICE ^L\NUAL Remove jumper, STEP #1 - Move lower lead of C16 from lug B to lug A, STEP t/2 - Move lower leads of R33, R35, C16 and green lead from lug C to lug BRTEP //3 - Move lower lead of R32, Cl5 and blue lead (C15 from ug D to lug - Add C9 from lug C to D. STEP
^
C)
26A
DRAWBARS
LOWER MANUAL
CONTROL
TABLETS
DETACHABLE MUSIC RACK
UPPER on SWELL MANUAL
Expression (volume) pecal
FRONT VIEW OF CONSOLE-MODEL M ORGAN

FIGURE 1
DIMENSIONS: AC INPUT: OUTPUT:
WEIGhfT:
45-5/8" wide; 25-3/8" DEEP; 42"HIGH 103 WATTS 11 WATTS EÎ.A. 249 LBS,
27
DRAWBARS
LOWER MANUAL
CONTROL
TABLETS
UPPER
PEDAL
MANUAL
MIDDLE
DETACHABLE MUSIC RACK
UPPER OR
SOLO MANUAL
EXPRESSION (VOLUME) PECAL
FRONT VIEW OF CONSOLE

FIGURE 2
MODEL
N4-2
ORGAN
DIMENSIONS: AC mPUT: OUTPUT: WEIGHT:
45-5/8" wide; 25-3/8" DEEP! 42" HIGH 103 WATTS 11 WATTS E.I. A. 249 LBS-
28
SYNCHRONOUS MOTOR
MUSIC RACK BRACE
PEDAL VOLUME CONTROL
DRAWBARS
MANUAL
STOP PLATE
MATCHING
TRANSFORMER
VIBRATO
SCANNER
LINE
WNEL
STARTING
MOTOR
PEDAL CABLE
GENERATOR CLAMPING SCREWS

LINE
CORD
EXPRESSION CONTROL UNIT
TONE GENERATOR
PEDAL IÊYBOARO
MOUNTING SCREWS
es)
'BACK VIEW OF CONSOLE
MODEL
M-2
ORGAN
(with dust cover removed)
FIGURE 3
29
PEDAL DRAWBAR UPPER MAKUAL DRAWBARS LOWER MANUAL DRAWBARS
LOWER OR GREAT MANUAL
UPPER OR SOLO MANUAL
CONTROL TABLETS
PERCUSSION
CONTROL TABLETS
"START" AND
RLJN" SWITCHES (UNDER MANUAJ-)
PEDAL
SUSTAINING
CONTROL
FIGURE
FRONT VIEW OF CONSOLE

FIGURE 4
hA'3
DIMENSIONS^
AC INPUT: OUTPUT: VEIGHT:
45-5/8" WIDE? 25-3/8"DEEP; 42" HIGH 103 WATTS 11 WATTS E.I. A. 249 LBS.
30
VIBRATO LINE BOX
MATCHfNG
TRANSFORWEft
SCANNER
RUN MOTOh
KEt BUS 3 AH
SHIFTERS
POWER Terminal PANEL
STARTING
MOTOR
AMPLlFfER
GENERATOR
PEDAL SWfTCh ENCLOSED)

PHOrÔGRAPM INPUT
PEDAL GUT OFF CONTROL
SWELL CONTROL
PERCUSSION CUT OFF
CONTROL
BACK VIEW OF CONSOLE (WITH DUST COVER REMOVED)
M-^
FIGURE 5
31
PEDAL DRAWBAR LOWER MANUAL DRAWBARS
CONTROL TABLETS
START & RUN

SWITCHES
PILOT LIGHT
UPPER OR SOLO MANUAL
LOWER OR GREAT MANUAL
PEDAL KEYBOARD
EXPRESSION (VOLUME) PEDAL
TYPICAL M-lOO SERIES INSTRUMENT
DIMENSIONS: 44-3/4" WIDE; 25-1/2" DEEP; 44-1/2" HIGH 155 WATTS AC INPUT:
OUTPUT: WEIGHT:
22
WATTS
LBS.
E.
I.
A.
2 68
FIGURE 6
32
TAB SWITCH ASSEMBLY
VIBRATO LINE BOX
PEDAL CONTROL MATCHING TRANSFORMER
SCANNER
START MOTOR
RUN MOTOR
SUSPENSION SPRING
GENERATOR
POWER
TERMINAL PANEL
AMPLIFIER
REVERBERATION UNIT AND

AMPLIFIER
PHONO
INPUT
SWELL CONTROL
PEDAL CUTOFF CONTROL
PERCUSSION
CUT OFF CONTROL
M-lOO
BACK VIEW OF CONSOLE GENERATOR DUST COVER REMOVED
FIGURE 7
33
SPGIIAL
IMPUT'
UPPER
WAAJUAL
0FMWBAA5
MATCHING
TRA^4S-
1
MANUAL
SECTION
VIBRATO
LINE
AMOUNT
OF
VIBAATO'
INTER-
VIBRATO
FORMER
OF
AMPLlFfER
SCAhNCR
MEDIATE SECTION OF
AMPLriEfl
EXPRES50N CONTROL
TABLET
LOWER
P4ANUAL
ORAWVBAftS
VlftRATO
I
ourmrr
RADIO-
g
5
u
CHORUS' TABLET
PHONO
.*>
SEC TON
OF
AMPLIFIER
o
VIBRATO TABLET
SPEAKER
PEOALS
PEDAL SECTCN OF
AMPLIFIER
PEOAL
ORAWBAR
PEDAL
cutoff'
PEDAL
PEDAJ.
PEOAL
SUSTAIN IMC
ATTACK TABLET
decay'
TABLET
CONTROL
VOLUME TABLET
FIGURE 8
BLOCK DIAGRAM
MODEL M ORGAN
RADIO PKONO'
I
UPPER
UPPER MATCHING
VIBRATO
WANUAL
DRAWBARS
SOLO
TRANS-
FORMER
MANUAL" TABLET
VtBRATO'
CHANNEL
INTERMEDIATE section of amplif;R
EKPRE^îO*^
OUTPUT
SECTION Of AMPLIFIER
CONTROL
SPEAKER
LOWER LOWER
MAP4LIAL
DPAVvBHftHS
VIBRATO
MATCHING
TRAhiS-
LOWER manual'
TABLET
viflRATO
VIBRATO
LINE
AMOUNT OF
VlSRATO"
VIBRATO
CHANNEL
SCANNER
FORMER
TABLET
X
VIBRATO cHonus"
TABLET
PEDALS
PEPC'J55rOt4
I
OM-OF
:>Cl
ECTOR
PERCU^S'ON = ECTIONt OF
AMPLIFIER
-{ DECAV TflOtET
TABLET
TABLET
1
UPPER" wA-CwiNG
THflNS-
ÔHJME TABLET
ADlO PMQNO'
I
VIBRATO
50L0
man.âl'
MO
ViBPATO'
FOavER
TABLET
CHANNEL
MtDJATE SECTJON O* AMPLif JER
EXPRE^ÎQPJ
Output
section of awpuifier
CONTROL
SPEAKER
VIBHATO
DRAWBARS
MATCMfMG
T H
LOAER U A^JUAl' TASLET
vlSFÂTG
VhSRATO
LINE
AMOUNT OF
VI
AM 5
CHANNEL
an AT 0"
vipflATO
FORMED
O
3
TABLET
5CANNEH
VIBRATO CHORDS"
U <
O
TA&LET
PEDAL SECTION
OF
PECAU
DRAi^flAP
AHPHFIER
I
pf:oal
PEOA?^
'
P DAL
PEDAL
SUSTAINING
CUTOFF'
ADJU5Tl,ENT
AT tack"
DECAT
vQlumc
TABLET
TABLET
TABLET
CONTROL
FIGURE 10 BLOCK DIAGRAM MODEL M-3
Vast
Of
cavVaa
ÔTT TA4
TAU
JPEttCy5^k4
i
ViM/^n^
CÂ^ÂAS
4H*ft-*^
Tft&t
LOWfTt
EVUv*ftA8^ -Afl
H
*
^VStT TAW FLUTES '
^CAL^
COIL
OUTPUT TERMINAL
MAGNET
TOME WHEEL
ONE Slot Of COIL CBOUNOED

COIL
FIGURE 12
-TYPICAL TONE GENERATOR
18
^
@ @ @ @ e \@ \0 ^^
\
so;
\@
(24)
\
'
\ \ ^
(5^\
57
^@
BACK or GENERATOR (AT BACK OF COMSOCE)
(60)
'Q
\
(SB)
(56
e e
(7^
\
13)
SYh*CHftOkOOS
STARTING
MOTOR CMD
MOTOR EM)
*NOT PRESENT ON Mi M-2t M-3

STARTING
MOTOR END
FRONT OF GENERATOR
SYNCHRONOUS MOTOR END
@
\ @\ @\
\
@ Q @
@\ @\ \ \
S^
(31
36}
\
(65)
\
40
A^
DOTTED LINES SHOW FREQUENCIES WHOSE TOME WHEELS ARE ON SAME ShiAfT
FIGURE 13
MAGNET LOCATIONS
ON TONE GENERATOR
36
riLTni TnjLMVDfitocni
ri''Ci>
C04KP4CM
iTUITiHC
95 We 6 ^
7|\47\64Vs8';69\*5\02\fl6' S7\9l\72\4e\5\a9\^^
-*
42"^ ^SVUo-*^
"ii'>^>^ 2^3-^'
^'3fl'^4V^
^^
^V3V*>i^^'V2"3/'*
*^'
,^76 ^ 54^-363
;;
59^y 6 ;
52 2^,
6.
^^
572V* ^ 50 ;^^79
"^^^^2^29^^ 5 ^22^ io^^V^ I ^' 20**^fl ^SV^
""^
I
NUMBERS ON FILTER TRANSFORMERS ARE FREQUENCY NUMBERS OF TRANSFORMERS NUMBERS BELOW TRANSFORMERS ARE OUTPUT TERMINAL FREQUENCY NUMBERS
FIGURE
14-
GENERATOR COVER MOOEL M ORGAN

-
FILTER TnAl4V0RMCII
fl42-|
Ul
MOTOA (t
STARTTHC UDTOfl END
Tê
^3'*^
^ !gB^4
NUMBERS ON FILTER TRANSFORMERS ARE FREQUENCY NUMBERS OF TRANSFORMERS NUMBERS ABOVE AND BELOW TRANSFORMERS ARE OUTPUT TERMINAL FREQUENCY NUMBERS
FIGURE GA- GENERATOR COVER- MODEL M

HR'AL
f*\jVlALn raOftS *PVC -JP
ORGAN
FIGURE 14A
37
o o
r r
O O o o m m
5 > > f" '' Z z c
Tl
o
> > rn
rp
> S
O o
'
I/)
It
<^^
en
m
-4
c c
O P7 2
W
>
o O o
CO
B CO
LOWER MANUAL -
UPPER MANUAL
DRAWBAR ASSEMBLY
FIGURE 19
PEDAL
KEYING
CONTACT
SPRINGS
CONTACT FOR ALL PEDALS
PEDAL CABLE
PEDAL TENSION SPRINGS
NOTE OF SCALE
GENERATOR FREQUENCY NUMBER
PEDAL KEYBOARD - MODEL

FIGURE 20
M. M-2t AND M-3
42
PEDAL CONTACT
SPRINGS
KEYING CONTACT FOR ALL
PEDALS
PEDAL CABLE
PEDAL
TENStON SPRINGS
NOTE OF
SCALE
8
9
10
12
13
GENERATOR FREQUENCY NUMBER
FIGURE
21
PEDAL KEY BOARD
MODEL M-lOO
OUTPUT
TO aJT TUBE
AMOUNT OF VIBRATO TABLET
IWUT FAOM
ej5 TUBE
H
SECTIONS or VtBRATO LIME
veAATO
CMOflUS'
TABLET
VIBRATO
TABLET
FIGURE 22 'FUNDAMENTAL OiAGRAW OF VIBRATO
SYSTEM
IN
MODEL M ORGAN
43
OUTPUT OF
h^^Rh#ÂL
A TO lin
viaPATO SYSTEM
boh.
20 L2I
Tl22Xi5 ^^* VTT"Ôl

U1
.000^7
D
w -
O O o
_
.
"I
VIBRATO
RI4
PHASE SHIFT L^NE
RI5
I2>ÊJS
"vibrato chorus"
Vl&RATO
"OFF-
X
FIGURE 23 -VIBRATO SYSTEM
MODEL
VIBRATO-
M CONSOLES BEH^W
StRlftL
NtjM&ER li509
r40RM4L
INPLJT OF
VlRRATO 5V&TEM
FIGURE 24-V^BRATO SYSTEM

NORMAL VibRATO
VI&RATO"
'ON"
MODtL
>A
CQKjSOLES
SERIAL NUMBER ii509 f^MD AftOÊ
44
OUTPUT TO
INTERMEDIATE AMPLIFIER
AMOUNT OF VIBRATO TABLET
INPUT FROM
MANUAL
AMPLIFIER
SECTIONS OF VIBRATO LINE

VIBRATO
CHOftUS"
TABLET
FIGURE 25
-FUNDAMENTAL DIAGRAM OF VIBRATO SYSTEM IN MODEL M-2 AND M-3
45
OUTPUT TO
AMOUWT OF VIBRATO TABLET

I
INPUT FROM
MANUAL
AMPLIFIER
SECTIONS OF VIBRATO LINE

VIBRATO CHORUS'
CELESTE I
fcELESTE
TAB
TABS
MODEL M-lOO
FUNDAMENTAL DIAGRAM OF VIBRATO SYSTEM

FIGURE 26
Lio
L2
LI
LI3
UA
LI6
LI7
U20
Lai
FIGURE 27
-VIBRATO LINE BOX-MODEL M AND M-2 ORGAN
46
L-1
Mf Gt
Later models use a somewhat smaller box, with metal framework.
T"'""'
'
FIGURE 28
VIBRATO LINE BOX
MODEL M-3
FIGURE 29
VIBRATO LINE BOX
^^^^^ ^-100
ROTOR CONTACT
PiN
ROTOR 'NSULATOR
END BRUSH MOUNTED ON LEAF SPRING
-2 SIDE BRUSHES
ROTOR PLATES
STATIONARY PLATES
SIDE
BRUSH
^
TENSION SPRING
A-BRUSH COVER REMOVED TO SHOW BRUSHES
B-VlEW WITH SCANNER COVER REMOVED (2 SETS OF PLATES REMOVED TO SHOW ROTOR
FIGURE 30 vjgRATO
SCANNER
47
OUTPUT O*
ST STEM
INPUT O*
VlflHATQ
vkaoATo t .ne box
^5000
VIBRATO Ph>5E SHIFT LINE

flâ
I
'lBft*TO
VIBRATO SYSTEM
(rfODE L W' 1 CONSOLES Stfli*L NijWBEfl
iMOO TO 2S25i)
FIGURE 31
OLfTFHjT OF
VIBRATO STSTEM
hWP JT
OF
*TD LINE BtMt
VIMATO
SrSTtM
NOflMAL
Vlftft*TO'
VIBRATO SYSTEM
UOOEL M-Z CON&OLCa SERIAU
fiuhiDta
2S2S4 AND ABOVE
FIGURE 32
THIS VIBRATO LINE BOX HAS DIFFERENT APPEARANCE THAN UNIT IN FIGURE 31
48
LOWER MANUAL SCREWS
CONSOLE
LEG
END BLOCK SCREWS
HOLE fOft ACCESS TO
LOWER MANUAL TERMINAL STRJR COVER

(S
UPPER MANUAL MOUNTING BOLTS
SCREW
SCREWS HOLDING MANUALS (VIEW LOOKING UP UNDER KEYBOARD)

FIGURE 33
NOTES
49
50
^Ti^V
N35a:j
11
< o
LU
Q O
O a
Jl
r
z o
O
1/1
3 o
Uin
z o z z
-J
<
ôvraTT
a
9
o o s
z g
Q
LLi
LlJ
<
J,
in
I
m
UJ cr
CD
N33tio ei
*W)-T-13A'a3tf CJ.
o-
imgici
A3U? ti
o
o
3 p
Ij-
rt
<
ir
m O Z Q ^
UJ
51
CI
m
UJ
?2 So
< m
u.
m o
V m
I
c
IP
^>
O
O O
> z > o
<
NOTE:
amplifiers coded "H" and above removes che positive voltage from che stacors of rhe swell assembly. This can be incorporated in earlier amplifiers by following the steps below. The end result will place a blocking condenser (.02 mfd, 600v) between pin 1 of the 12AX7 and the swell stacors. This change will insure continued noise free operation of earlier amplifiers.
A change
in all
Step tfl Step Ul Step *3 Step UA
Move lower lead of C17 from lug B to lug A. Remove jumper. Move lower leads of R33, R35 C16 and Green lead from lug C co lug B Move lower lead of R32, C15 and Blue lead (C15) from lug D co lug C. Add C9 from lug C to D,
r
=^s^
:_i
"
^^^^-^
PICTORIAL M-3 AMP (PARTIAL)

r
FIGURE 36A
53
54
CO
W W en
o o
I
a;
-I n, to
O m o o
O m
o
I/)
m
Ui
55
u w w w w tj >>>>>>> o o ooooo
ti]
*i
J
CQ CQ CQ CQ CQ CQ CQ
Q Q Q Q Q Q Q o X CO ^ ^ O CO ro ^
^^
fvj
u^
f\j
r-
-^ -^
^ O '^ vD vO ^
iTi f\]
in CO Lr in fo in f\j -^ no ro tn
iTf
O O O ^ ^
rn -H CO
vD
ld
4
on I
<1>
m
UJ
:0
O
AAA/^
=s
> o
P
r
or
o o
r
<
c/>
\^ rv
*
>
o
m
rs ra
B ^ g & o rn m 5 s -^ cz o ^ m n
4
FN)
cr
?^
C3P
5 5
trt
?
--
O 2
TTTTTaTB
-I
o o
i3T^ ?
?l
p e
ih
si
w
en
/\
i'
58
MANUAL
UPPER MA.^^JAL
AMPLIFIER
--vv.v
INTERMEDIATE
AMPLIFIER
EXPRESSION
lOV.
OUTPU
CONTROL LOUD _Y
AMPLIFIER
C44
300V.
DRAW9ARS
LOWER MANUAL DRAWBAR
MATCHING
22 MEG
TRANSFORMER
Tl NINE
'
MATCH
TRAN' R4
6. a
MEG C6
.005
.000015
W
}*-
J ^^d7nQO
^l
C35
.000015
I
R27
R29
BUSBARS IN 0RAW3AR
SMEG;LdMEO CIS C40
V4
feSC7
^SCANNER^
?
5CAN
PEO"
,0002 .0002
4__^^
25V &
?j:i^
-
1
,4-VW.
P5\2.MEG
Rd
KEY CONTACT
I
RESISTANCE WIRES ALL

J6
OHMS
EACH DRAWBAR HAS 2 BRUSHES
CONNECTED BY ONE OHW RESJSTOR

at <h
TAPPED 1/2 OHM RESISTOR PROVIDES ^NTEN3tTY STEPS FOR DRAWBARS
SPEC
INPUT'
.25
AMOUNT OF
J|_l
C36
R25 VA* MEG

1-5
NORMAL J--/--/--/-"
SMALL
d:
5^-LU
^< SET
<
i>Â*jv-o
OF NINE CONTACTS Ur^DER TYPICAL PLAYING KEY ON
UPPER MANUAL
NEGATIVE FEEDBACJ^
CIRCUIT PROVIDES VOLUME
yiBRATO LiNE BOX^ TERMINALS
c-AVAr<i
LOWER MANUAL BUSBARS
COMPENSATION FOR
'VIBRATO OFF"
r"
VIBRATO LINE BOX

TO CONTROL PANEL
TO SCANNER
D
D
rr^
-z
IIOOÔCCf.CCOCODOo'-'
z2:cijc^ %^
X 3 '^~n ^TO amplifier
DRAWBARS
-i
A-
BK
CO
^
MATCHING
TRANSFORMER
/-
Bh
Rt
r^
PEDAL
TO AMPLIFIER
DRAWBAR
CONTROL PANEL
TO MATCH. TRANS
TO CONTROL PANEL
LINE \
TO VIBRATO
TO AMPLIFIER
VIBRATO LINE BOX
NUMBERS
.GN fB^
4 BN WIRES TO VIBRATO LJNE
H^
UprÊR
G a
^ FROM MANUAL
<U
75
74
52
51
29 ze
rs
MANUAL
BUSBARS
GY
BK Wtf*ES TO VIBRATO LfNt
6
BK
'
V
,11
FREOUF^*CY
J=dt.. t*.Uo
C CN WIRES TO
SCANNER
CT'jiX'^^^ygj:?,'
HI
c 6
i
l_OWER
NUMBERS -
6 o 6
6 6
cooooc
Qcoboo
DQor
29
11^'_
75
74
MANUAL
TO GENERATOR
eCN WPRES TO CONTROL PANEL
lA'
JUMPER WIRES CONNECT SCANNER
TERMINALS OF
B5
c
\
2
.
GENERATOR
669 WJo
7i o
TO CONTROL PANEL R42

72o 4&v 65 BOO 41
89o 70c 46 o87
47
640 SBc
69^
15o 62g BOc 7c

3&9
o
43;
3Ji;.
Sf p
06B d44 cCl

I I
^\ SAME NUMBERS
P*-
AZ9 309
3S9
339
S4c
i39
^tr?
/f^
J-^
BK
^ BOTTO M
T
L.
^Â
"
-7
/
-^3 WIRES TO BN BK ^' VIBRATO LINE BOX
76
la
54 ^83
6^ 23
^
59 ^ 76 52 M^ 28 4T 21
ftf
*! 57 30 9] 26 2, IQ
.
79
55 ^ 7^^ 24
77 12^
_53
sT
c49^ FREQUENCY NUMBERS

o
20
25
t^
11
VIBRATO
SCANNER
jv-'Vif'vwjrjj^
'RUNSWITCH
'START-
BUTTON FROM CONTROL PANEL

J
FROM CONTROL PANEL
^db^^ r1
I 1
'
AN
"
AC LINE 120V MOV BRWN GREY BLK
SPKR
FIELD
WH
GY
,
BK
BK
ISN
YEL
BK
BK i5 iBN BL
1
LINE
PANEL
YEL
GY

VIBRATO LINE BOX
P-T [T'Z
^ Z<:22:tx<:c^
TO CONTROL Panel
.
TO SCANNER
-^^---"^w_^^
^"V
^fafT") ,T0
AMPLIFIER
DRAWBARS
MATCHING
TRANSFORMER
HK
OJ
^Trj 1^
TO AMPLIFIER ^^*4
PEDAL
DRAWBAR
CONTROL PANEL
TO MATCH. TRANS
-TOAMPLJF"IER
-TO
CONTROL
PANEL
V
rr'^TT'^
r.
4BN WfFES TO
VIBRATO LINE
rni
~^
UPPER
7"
74
13
5'
29 29
16
MANUAL
FROM MANUAL BUSBARS \
fl
^
GY
BK WIRES TO VIBRATO LINE
BN
'.
>/'.'
'
1^
7^"'"
"7
T-
"T
U
60 00
t b
f>
u
3060
29 2&
\A
6K
\^h
6GN WIRES TO SCANNER
FREQUENCY
hJUMBERS
ii>
6 6 a 6
OS
75
000
74
660
LOWER MANUAL
EEC^CSS^
^^ctctt:^:':':^^'^':'^^^'^^?^
GENERATOR
Tl'
CN WfPES TO CONTROL PANEL

e
GENERATOR
o
^
R423 6c
-i^TO CONTROL PANEL

0'
CONNECT SCANNER' TERMINALS OF SAME NUMBERS
42? 309
90T
:>
359 **Oo
71
339
3a';*
43?
ii
31 11'^
CI
o
'es'^
^^ 34p 390
a
47?
-tr.
64^
ae-
eg? ^45?
02?
i
ae^
e/"
8i^
i
72; âf
~o 70
'
4fl^
fl3
S7
eSi
|44
SI
BK
BOTTOM
LLXJii!
.
till
T
50^79
63 BN BK
59
76
52
5534 BO,77_53
.32
13
^*<EQUfcf^CT
i.
NUMBERS
53 ^75
5i
.30
50 .73
"
VIBRATO LINE BOX
VIBRATO
SCANNER
tr.-^tJjr.T^J
P iif ^ f
TrTT--"=cxrj'!^?3&^':^^
V RA^XJlTV.A^Tl
rt'-Ajj.AJTi
run'
SWITCH
'START-
BUTTON
FROM CONTROL PANEL
SPEAKER
COLOR CODE
FROM CONTROL PAN;L

I
i
FROM PEDAL DRAWBAR
l^3i
r--,
BN L
>
1?__!
^
AC LINE I2CV nov BRWN GREY BLK
III3
PEDAL
IN
FROM CONTROL PANEL (PEDAL DRAWBAR} FROM

MATCH TRANS.
5PKR
FIELD
DECAY SUS
WH
BK
BKl
SW
SW
VOICE COIL
PED
KEY
BNI
VI
SCAN PED
BK
WATCH TRAN
GN
GN
6K
WBK
GN
BN
YEL
BN
V
GY
BK
GY
fBN
BM
BKjBK
;B N[BL
\^
LINE
AMPLIFIER
PANEL
YEL
BKi
r
LOWER WAfÛAL
t
MANIUAL
Off
AMPLIFIER
OOOOiO IN SERifciMO ^b49& ANO AbOVt
C20
IS
INTERMEDIATE
AMPLfFlER
EXPRE35*0N CONTROLT
CiO
OUTPUT
,0OOD24-,000CO
AMPLIFIER
0*TCMlHG
Q?eBRE^59?
BagaR
TZ
THA^SFOHMfP,
'vibrato
MA**UAL
RiV
(5tT AT *ACTO>')
.000025
CIS
GENERATORS
49-91 OSE THtS DRCUlT
'vibrato !i:"H^
'4-^.
V4
LOWER
uanual.'
I^mLG
6SC7
.0DC2 R2
\ ^' - SOFT
r^
*5 5NT^^^^ C2S
g>oy
jO
ON'
i-4=
ÊLttTED FACTORS TO
eALAdC(.
20 I'ûEgJ LAUEG
>
tTh
r
t
I
m
2tlV
* -. '^2*0
M
ZU)
1-1*0 B
4
^\t
KtT CWJTaCT
CHAhSELS
E5i5T*NCt
DR*WB*n
lb
R2
0.2
R2A
2.7H<i
VI
OKU2
(iENtaATORS
^ BRUSHES ONNECTCD Bv
U
cJ
-OOI
K -f o
+Z90
k4&
A4-4B
Ohm RESI5TOH
VJB
"^
V3
VJSE
THIS CiPCUJT
ff^
S^-^
47000
t5J7|z5v I, (T-^-^ti
*Z90
1^
60 V
ri
'AMOUNT OF VIBRATO'
or s.
ipW
itj
SCANNER
>.
^
lu
*Z40
U^
\
-^SM,
5tT or
CONTACT! UNCER TTPJ C*L Plating fÊY OH IJPPH U*NUAL

NihiE
^
viB LINEfC).
(V
>
--LI
LOWER MANUAL BULBARS

VIBWA70 L^Ng
Y^
BO*
TERMINALS
16-43 uit
THIS CIRCUIT
/i
'vibrato
^JNOHMAl
CMOnuS'
SET Of NINE CONTACT! UNDER rTf*iC*L Slaving utT ON
\ VIBRATCT
h^
'
< p > o
ru
^\
fO^
EIACT
vlMATO
IS
CtRCUlT
LOWER UAhUAL
SEE rifcURE
\1MS1
NEH*TOW OUTrUT^ TERMINALS
OV. AMY PEDAL PRESSED v
(
VIBRATO
PHASE SHIFT LINE

NORMAL VOLUME
"SOFT'
Ai^L
NO PEDAL PRESSED
NO PEEAL PRESSED 260V ANY PECAL PRESSED S5V
PEDAL PRESSED 45V AM" PEDAL PHESSeO 55V

N]
DC VOLTAGES MEASURED
iVlTH
20000-OHMS-PER-VOlT METER
^
PEDAL^^MPLlFiER /
^
"^
MEIf
^05
^Z
-M 4s 4^
ZiO
f>i
^
RUM SWITCH
120 V
POWER TRANSFORMER T4
fc.1V
POWER SUPPLY
HEATERS
o< BLA
-START-
110
tZVO
PEDAL CABlE
RB?
?5o
-t-ZftO
STARTING
STNCHBOtslOUS
MOTOR
WJTTOH (looo FOR
MOTOR
^
a4Dv)
'-ÊYSw.
Pes
4700
R74
-Zi
GREY
'ÂVv
HEATER RESISTOR
V)
3ii W
Ra
ôoo
-z\
E^8 "^S 3,.
ATT- KEY
39 MEG
RM
^DCCAT Sw'gj'suS ÔRual'

FAST
Sw"
(iBDDOFORiAO
EMRRtSSrON COhYWOl
'OFF
T3
T4
ON
PEDAL
Sustaining
PEDAL
ATTACK'
"PEDAL
DELAY"
CONTROL
od"e
SCHEMATIC DIAGRAM MODEL M-2 ~ 19000 AND ABOVE FIGURE 42
ff*gg*a*^b
PEDAL HErlN& CONTACT C^.OiES AFTER ANY PEDAL
000@0@0
TOP VltW OF AMPLIFIER
*
\H
SPEAKER
70O
lELO
^fcrr^
OHMSB
EARLY M-; CONSOLES (seRlAL ntfS. &ELOW iljso) RBS IS S4000. Ra7 (1 jOpOO. Af*D SPEAKER FIELD IS lOo! OHMS.
pedal contacts
CONTACT OPENS
SCHEMATIC
SERIAL
DAGRAM- MODEL M-2
lUOO AND ABOVI COUPLES VIBRATO line; SCRIAL WUUR nz4 ANDAbOvE
NUUBEn
62
VIBRATO LINE BOX

TO COMTROl
PAiÊL
TO SCAHWE-R
TO GENERATOR
WIHE5 TO COhTPOL PANFL

6
G^J
STARTING
SYNC.
MOTOR
MOTOR
SERIAL NO .9000
AND ABOVE
WiRtNG DIAGRAM OF
HAMMOND ORGAN CONSOLE MODEL M-2
WIRING DIAGRAM MODEL H-2 - I90OO AND ABOVE FIGURE 43
63
DRAWBARS
VIBRATO
TO CONTROL
MATCHING TRANSFORMERS
GY
LINE
BOX
TO SCANNER
GV
T2(lDWER
M^NiJAt.)
Tl(SOLO manual)
PANEL
TO QEHIHAJOR
6 GN WIRES TO
CONTROL PANEL
STARTING
5YNC.
MOTOR
MOTOR
WIRING DIAGRAM MODEL M-2 - 25254 AND ABOVE FIGURE 43A
WiRlMG DIAGRAM OF

I
COUPLED VIBRATO LINE SERIAI. 25254 AND ABOVE
64
30LO
- VlB*UTO -^
-WW
ft2< 10
R 30
,0000.^0
C6 MANUAL AMPLIFIER
CI3 iroooos
OUTPUT AMPLIFIER
cz
EXPRESSION
T
iMATCHING
ORAw6AaS
Fl LJLJLJLJL^
SOLD
RRRH
n22
5 3WF:G
MATCHi^JG TOAMSfORiv
MEG
COMTÔL
/LOLjD
cÔ |jOQQO^Q
r4o; Cî
OJ
ogog:?^ V 3B 2AU7
5ET At TACTCRV
C25A
.001
ooaogo
^-24
VIBRATO
KTOOc!
^
LOWP
majjllal"
0000^7,
305 V
R4Â
.2'
CIS
CI6
.0OO2 2
â
i/
^ SOFT
^^-l-
MEG
N-l
*.
GENERATORS
4^'^L 1J5E THjS C<RCU(T
OOQ2 5 R3Z
*l-5
o
-+250
VIBRATO / CHAf^MEL
INRJT
50 SELECTED AT TACTORV TO
^MEf^
s-;g
BAQIO
PHO O
^7ME&
H6 00O03O
"fl 2
BALANCE CHANNELS
u
l^
.^^-^
ul
ftiôrt
^^90 v4a;
^^s
=-
3
SPEA-ÊA VOICE COIL e Ohms
^?MG
r/zu-rV-Â
R7
C^.
/Od
n3fl<5 .56 v^:.
VIBPaTO CHANNEL
INJPUT
lOWEG
7MeG
te
t-VjVw
R5
6AU6
VI
0047
V3A
I2AU7
CSI aND qj ARE OWlTTCD
3CSV
I
m]
GENERATORS
VA TEflvllSiAL6(5 ABOUT 'OC vol ^ i^lgA 15 47MELJ *ND <3 CONNECTED PE"wCErj IfciiMirJAufi AMD Ci-OUND ify CODE A fl ONlt,
c27 used only \n Amplifiers code f and above.
V4-
R5Â
'1,6
b,j
1 1
RIO
OMLV '139f3?rîJ CHMe.)j5 CONNECTED &ETa?.^ V4TEP,WiNAl 5v QlAS^ i CODE 3 iWC CC-JUNDj AiuD USED INMEADC"
i5
1*4
OMlTlt^
C:Ê.i:
>
Q
<Xi
5ET OP
r^t^
MWE
CGMTACT3
KEY
MEG
zgo
PEDAL SIGNAL
C Oncf.
^JOTE A^P'.LFiERS w;th no LETTE=J a:Ê COCE A.
maraeo code
"urJOEH T^'OiCAL T^LAYIPSG
PERCU55
;*-l7
AMPLIFIER
4hH
ui
CQUJACT
.^C2B
RESISTANCE WIRES ALL

IS
rJ
"T
PERCUSS lON
A"'
VOLUME
OP VJBRATQ
5î^.AL.
047
Tt
PERCUSSION
.
QMMS
HAPMOMLC
Rid
20OVT6
y 4700O
C34
PEPCU'SSION
ÔFF'
I
SELECTOR' Third1
W
ô5
\ 205-^
'
"f^.ODl
"On'
T
-SECC^JD^
rfl
I I
Sr-1ALL
RSe*!**
?oov5
"^
[^7000
vg
&AL*NCE CHANNELS
J2AU7 SELECTED AT FACTORY TO
ViSRATO LINE
SOJf TEt^tMIKALS
on
i/i
K'^
LZ
fy
GENERATORS
;6-43 USE TH15 CIRCUIT
'per C 'J SSI ON

-r-'VWv
< o
<
IT UJ
nee ^.7MG
<JR5'*
3
COT OFF"
1.
MEG
'i'EPCUSSlON decay"
SI
PERCUSSION VOLLJMe-
\wv4700
fôaMAL
r:53
25 V
lJ
^ÛOOO
Q-O ^'AVv
-=-
-VIBRATO
PHA5E 5HIFT LINE
PEDAL AMPLJ FÊR

z
ENEHATQP OUTPUT
TERMINALS
J^
-z
PEO*L
OFÂvêAa
vio
6BAfi
C59^ô^
POWER SUPPLY
lEATER
PESiSTOfl
TRAP4SfORMEH
POWE^
T7
;-
Ji:
'^gc'
j-\
4SO0 (JQOOO FOR Z34VJ

NO PEDAL ^HISSED 290V ANY PEOAL PHE55EO lOOV
S
RUN
I
R96
R97
150
RIGC
TC H
t
R30
STARTING
6 0V HEATERS
zcoo
6O0O
2200
NO PED^L PRESSED OV
ANY PEDAL PRESSED
JV
3J0
C63
SYNCHRO-
Z:
^. waeov
380 V
^^%oo
*^ôo
M
= EDAL
PEO-L
'
TART
CUTOFF
CaSlE
377
iWlTCK
-o-
250
MOTOR
MOTOR
NOUS
S
"J
.00220^
C6I
^m
JUMPER f
IN
SPEAKER
Field
-tOOV
4700
'WW
IZMEG
S.9Me G 2 5 MEG
R62
'ZZ
CY
700
TiTTTOMMS
Rioa
PI
RlDI
03
T5
,r
j.^^
.
r/>
V6
W6
FA5r
ti
NORMAL
T7
EXPfÊSSJON
'off
CONTROL
ALL DC VOLTAGES WEASLRED WITH ZO.CDO OHMS-PER-VOLF VIETER^ ANO ALL CONTROL TAGLETS TILTING TOWa^C ^RONT OP C0N5OL
SPEAKER Plug
.VÂV-
390OQ
-60O
-19
lOOOO
r-'
PCOAL
ATTACft
PEDAL SUSTAINING
/^
T6

MODEL M-3
SCHEMATIC DIAGRAM MODEL M-3 FIGURE 44
PEOAL DECAT
TOP vjew of amplifier
CONTROL
CD
^
DF F*GO*AA"a
IN
PEDAL SIGNAL CONTACT OF LA^T REOAL RRE5SED REMAINS OPEN
.i^ PEDAL rtEVfAlG CONTACT CLOSES AFTER ANY PEDAL CONTACT 0PEV5
AB-T'VG
SCHEMA^C
SEH lAL
IN CCLIE 4
DIAGRAM
NUM&ER JaX3 AND AfeOVE

#* USEi ONLY
IN C"L. h A Ahfl-^LlFlt Vti
UÊD ONLY
AMPLIF'.ER^
CODE &
flS;D
* VALU6
AMPLlFi^K'
22A
65

on
/
IMATCHING iTRANSrc'^MER
ijpOfP
P20"
RSI
JVSV
10OO3C'
-^
MANUALS
r
I
I
LOWER MANLfAL
y ^-
"viBWaTO-D'
DRAWBARS.
OBfflS
wATiHtMG
SOLO. MAMUAL
i7MEG
R2P.
iNTElRMEDiATE AMPLlFlE^R
CI3
J/
OUTPUT AMPLIFIER
^
OODOH
EXPRESSION CO^JTROL /LOVO
CI5
CI6
"on
CZ3i;*'5ETAT fACTORV ^-^
25A
lOMEG. .\3MEG
CIO
ON VtEPATO -^-w^-r
CgPnQOOCg Q
^t
'2Ai7 r4DV
CZI
I
0O0D24
R4G
00D090
305V
,V6 ^
PJ
i>Ol
470od
4*^%,^_-4\w. iL_ J^^^l47MfG
V^5
LOWER
wanual"
GENETS A TCR5
MEG
6V6
u
-WA
.27 MEG
49-91 USE THIS CIRCUIT
'^*230
NON VIBRATO CHANNEL
INPUT
.27
5:lECTED at
O0022 ^002 E t+3? R32 A/i^-' VvW SMEG 6 MEG O

I
op
HADIO PHON O
.
T3
"O
290
o
5tOV
FACTORV TO
"^^
MEG
_[_
BALANCE CHANNELS
^^
+290
(tROM V4A)
o fr^2 u
in
,^^v^
AflA/^
.OG002C
rVW*-
SPEA COIL e OHMS
2?MEG
R5
VlSR'^TC' rlHANJNEL
I^JPlJT
t^MEG "OMEG
C3'/00l
&Aue
VI
0047
I
iAU7
V3A
AMF^HFL^R CCDE G ANC ABOV
Ol/T^P JT
3C5v
CODE
H ANjD A feOVEl
C.3
ACE:'ED
GtJEPATQR5 A4,4B USE THIS IlRCUiT ,^
DjIC-^^
PtlDAL
SjGKIAL
=0!
CC^JTACT RE5t5TANCE
KEEV
SET or M^JE COT^TACTS UNDER TYPICAL PLAYING KEY
P^RCUSSiON AMPLIFIER
R47 r^W^
T4
C26
v7
v9 T5
'
VOLUME
2ftU7
WIRES ALL
ffi
I&
0KM5
4 7 MEG
R^
^00vT6
PEBCUS&ION bl&NAL
AMOUNT
or VIBRATO
d>
PERCUSSiOhi
PERCUSSION SELECTOR"
'OFF'
!
'THIRD"
I
H4
^047
SMALL
RNÂL
"ON"
-SECOND"
^
rt
200\H
'
V9
I3AU7
J
+
ViGâTO LIME BOX TEfiroliÂLS
-f
/
.VA:-,-VVvVA-
SELECTED A"^ FACTCRV TO &ALANCE CHANNELS

4#
*32
GEtÊRATORS ie-43 lse

THIS CiRCLIIT
PERCUSS'
JO
-VAV 4.7WtG
R59
-<^
l.Sf^CG
R60
CUT
E47
LJ
L3
L3
01
^
PERCUSSION DEC*Y
i\i
13
l*Ena;5SioN
WVv4700
VOLUME-
R55
25 V
R57
62000
nj
/5LOW
EAST
R5D
id
-=
NORMAL
i32
:^^1200C
-VIBRATO
PHA5 iHIFT
i_lME
PEDAL AMPL nC-R

I
IERATOP OUTPUT
C56
VIO
TERMINALS
e9A6
DRAW&AR
01
cÊDAL
POWER SUPPLY
^'^^.>^. ('^^5E:j} D91 RE5:6TOR
iJ+-
310
Q+^90
_ transformed
powe:^
T7
t20^
^3Z
4500 fiSOOO FOR Z54V)

-
R93
R95
-A'AV-
NO PEDAL PRESSED 290V

ANV PEDAL PRESSED lOOV
c
R90
.000 FOR
t.OV HE ATERS
50
SOOO
C6
WA60OO
^/. DO 3
R56
RiOO "2200
A
'400 ^.
NO
PRErÊD OV ANY PEDAL PRESSED (V

PE1>^L
R65 300OO
PEOAL CABLE
Bl
STARTING
PEDAL
'START'
Cutoff
^VvV
5w;tch
'-2 2
250
MOTOR
SYNCHRO NOUS MOTOR
380V
C62
C&l
-L
^^.0022
450
OVAV 4700
S
^"^7
Rei -VV/v-
3gMEG ^^MEG
^^^-^l
GV
T^:^H
f
L ^v
-lOOV
SPEAKER
niTrm700
FIELD
-0=
JUMPER''
OHMS
RiOE 'AVvt
Tc57
T3
V6
I
W
i^PEAhÊR
RiOl
R105
TS
!T4
y6
T7
EXPRESSJON
CONTROL
ALL DC VOLTAGES MEASURED WITH ?aOOO OHh/S'PER-ÔLT METEP AND ALL CONTROL TABLETS TiLTfNG TOWARD FRONT OF COWSOlL
P-UG
i90OO
'2 2
leoo
-19
r !T6
V: 25
PEDAL
ATTACK""^'
O
PEDAL
SUSTAI.-ÎNG
*--'
CCDD'EF F-GCAA'B
PEDAL SrGTÂL CONTACT OF LA^T
PEOAL PRESSED REMAINS OPtN
CLO&Eb 1/VMEN AWV PEDA.L IE ri^L^ÊD (AFT F.R. PECAL SicUAL OCMTACT OPEN^)AfcJO CPCN^ WHEN PEDAL 15 RfcLeAÊD
PEDAL DECAY PCDAL I\EVIH& CONTACT
TCP VIEW OF AM^LJFiER
CONTROL
SCHEMATIC
DIAGRAM
MODEL M-3
SCHEMATIC DIAGRAM MODEL M-3 - 904-85 Aid ABOVE FIGURE 44A
66
^
"OFP;
r' T\
intermediate: amplifier
V4A
EXPRESSION
UPPea MANUAL5
DRAWBARS
LOWER MA>JLrAL DRAWBARS
"VIBRATO
TjKj
IMATCHING
I
TRANSFORMER
SOLO >S MANUAL' "Of MATCHlWG

RAîS^GRMER
-^
R20 ^7MEG
-V/vV^/A^v---
AMPLiriER
OQl
VUviE':*
Output amplifier
CONTROL
C?0] /OOOOZO
lOMEG
4TO'
d
G^CRAT0R5
THIS CIRCUIT
ON
VIBRATO
P2B
47viFf^
CIO
A^v^
,.0000 27
,2
I2AX7^,
7
C5 lETAT FACTORY 000024 -OOO 090

CZ(
o\
^^
MEG
l-WV^J
c^5
Cl6
/LOUO
V4&
J2A)7 W3s^
R40
47 f
LOWER
MAHVML
'
<o
fl)
A SOFT
oTgr
RAOIO " p fÔr4 o
ui U>
-
30SV V6
MEG
0002? D0Q2Z R32 R33
6V6 "
M
T3
-WW
2<^
CZ7.
ISMECX
I.BMEG
^'2-
J
'255
"0-19
krt
NQN VIBRATO
CHAt4NEL
iA
*l 5
(FROM
VAj
UPPER
LOWfR
MAMTJAL
INPUT
MANUAL BULBARS
R23 .27MEG
SELECTED FACTORY
Of
Ti:
Ti^ >fo
q:<
BALANCE Channels
o
[ti?G*l
J44^
"^
c:
*3zo
SPEA^-Efl vOfCE
BUSBARS
c?o
o-'AW
^
VI6RATO C*ÂNNEL iNPyT i^
^
'ev6
2V1E5
COIL S OHMS
'
R7
Rfl
lOMEG 2 7 MEG RS
I47G0'
VI
fiALie
00-17
C4
AMPLIFIER CODE T^P OMfTTED.
Lrt
GENERATORS
44^46 U5E
CDO^ CODE
M J
AND ABOUE - OO'^ÛT irJD A60''E CI ADDED AWD AiiOi-e - P4 SPf,/><ER.

<i
-
3CSV
TTHIS
CIRCUIT
^
SET OF NINE COh^TACTS UNDER TYPICAL ^LAYI hiG KEY
iÊY
si*
O
*265
Pl^DAL
(FROM
SlGWAL
PERCUSSION AMPLIFIER
R47
47 MEG
CO^JTACT RESISTANCE
WIRES ALL
15
OHMS
c2a
15 2AU7
O
PEi^CUSSlON
VOLUME
R46
C s
PERCUSSION
"OFF
t
PERCUSSION
HARMONIC
"THJRD'
t
I 7
M4
AMOUNT
9
OJ^
VIBRATO
C34
,001
SELECTOR"
SCANNER
R46
4
SMALL
2a
MEG
'ON'
"SECONO"
Inorwil
p^
v9
lEAtn
"^n
ViSPÂTO LINE
aOJf
\
U
GENERATORS
ie-43 USE THIS CifVCuiT
SELfTCTED *T FACTORY TO BALAf4CE CHANNELS
TERMINALS
.-^
L
-31
-H
R60 'VW^ 4 7MEG R59 l_V/, I5WCG
'pERCuSSiGnT CUT OFF" j
o
1^
l2
l3
lS
L(0
LI*
LI2
LI4
jus
8
iriJ
iSSlON OECAY
'\
J
CN
t
PERCU5SIOM
R33
25^
4700
NOClMAL
P57 w\^ 32000
g_ u
g_
i
Si*
^J
^_
VOLUME'
^^12000
-^Wv
-=^
>32
VIBRATO PH A5E IM\V~ LINE

PEDAL AMPLI tier
P^DAL DRA*VBAR
CS^.,01
C^
o
eBA6
POWER SUPPLY
RESISTOR - __,V.'., J50O CieOOQ FOR Zi4V)
R91
f'*"
'-^Ê^)
TRANSFORMER
T7
5 0V HEATERS
PQWEO
*320
-^
9-^*5
ntoo
*32
R92
'J}Q
R96
Ft
97
NiO
ÊCAL ^^RESSEb 2qOv ANY PEDAL PRESS-ID lOOV
60OO
C63
=9^ 00
ISO
2300
T:
'"Sioo
-235
.
I
Û4
0L
ff
/"
Ct2
MEG
^CUTOFF
:D^-=^
g^ 30000?^ PEDAL
1
RQ5
STARTING
-START' 350 SWITCH 1000 FOR
MOTOR
S^NCmRQNCU5
320V
-J
CbZA
'450
eioi
4go
MOTOR
C6iJ-
^'
-^.0022'^
3201V.
234V
GV
IfiO
O^/vW4700
S
77
Â^^VJ_L2MEG
^$? V-r^^-2 2
3.9MEG ^2MEG
T3
v6
I
X i
EXPRESSION
NORMAL "OfF
I
CONTROL
^s;
ALL DC vClTACES MEASURED WITH 20.000 0HM5-PtR-yOL7 Mt'EP, ANO ALL CONTROL TABLETS TJLTING TOAyiRD FRONT OF CONSOLl
10 OOO
stooo
C64
-wv.
Bi02
-leo
25
PEDAL
ATTACK^
FAS
ON'
,V5
rJG
(V6V
(V5
PEDAL PLOAL hEYlNi-- L'^'lTACT OECAY LLCf.ci. ^mEN any pedal tC IS Vr^..-^^. U AT
1
1
PEDAL SUSTAIN
TO^ VIEW
OF AMPLlFtER
CONTROL
PEDAL Signal CONTACT OF LAST PEOAL PRESSED REMAINS OPEN

\
PF - _ S" -*JAl_ I.C^TACT (-,N'ij) ASjn OPEN'-t Wf^N PtOAL IS ftLLEASf O

.
SCHEMATIC DIAGRAM
T F-'-^
MODEL M-o
'iPtA''
'yt'\'\^\.
ri'i.
OS -If I
AN
"'VI'-
SCHEMATIC DI AGRAM MODEL M-3 - 09466 AND ABOVE FIGURE 44B

1
67
1
DRAWBAR5
VIBRATO
line:
box
TC SCA^m^R
BgaBBBegg
g^ggBB^
MATCHING TRAM5rORMER5
TO COWTflOL CAMEL
FREQUENCY
NUMBERS
t GN WIHE^ TO
COWTROL
PAJt^
t:
^^
GENEiRATOR
??
85
6
90i 7
TQ
O 54
6*^
% 5^^
4
CC^JNECT SCAKMER TERMl'MAL^ or

t.
I
<?
3^9
""3l"0
X C37
ZL
C
SN_,
BL
-3-
V^
45
g
ezi 2|
lL
c O
2
c Be
E
~^^
1
^
IflN
B*^
67
91
73T
4e
\iRED
c
OTTOM
o
^3
p 1 5 TO VIBRATO LJNE &CX

I
rHEQUENCY
6^^ c.^^t 83
16
^,S9
1 ^6
i
8J
/^
PERCJSSIC^J SWITCH
_fÊAR
-yjly^
WH v..
WJTH COVER
^^
52
4
2\
^57
9 26
74 ^50
79 .55
24
fi*
irl
26
oô ^ 77 ^53 121 2^ 5
?E_*ÔVEp;
VlBRATOE SCANNER
ri :_
-,-^-"
"VT^
"^rr^^>V^'^>^^"^"^^Vi:
^-
--.-.vT.v-.:r^>j.-
^^-ite:
J
^^run"
CO(_0 CODE
"start"
switch
BK
switch
orF
1
&N
B BN
Black
RED ORArjGE
rp^
0N
GY
ED OR
VEL
5PE*KPR PLUG riTS RECEPTACLE OU AwPlIFiER
GN
BL
vÔ
YELLOW GREEN
BL'JE
VIOLET
GY
CEY
WMITE
i
PEDAL
Cljtoff
TEL
I-
r^
GN
V
(J
R
L
X
|R
WH
T per:u5Sion'
Bk
BN BL
^^
GY
Bl_
LINE
PANEL
R90
TEL
BN
YElRgn"":
>t'jTTL
^^
BLêf^ GH
-^ri
^1
CUTOrF
'
i_ _^ J
AM_PL_lFiER rîWJ r t_n |_ >

*
J
BN
BM
BK
BK
(BL.)
Jbl G^-JK
i
|Bk_|sk_|BK_^!6K_^|BH_|Bk
11
fBL)
w
10:
TQ .Su STAtN 5VVITQ1. *^Dn EKPRE^^fCfJ COhTftOL
rREO.rJOS
10
fi
^
d'
rJ3TES
^ D
^*
C*
PEDAL KEYBOAPD
STARTING
SYNCREFERENCE SYMBOL^ REFTR TQ SCHEMATIC Diagram of o^^GAN mOD^L MO
MOTOR
MOTOR
WIRING DIAGRAM MODEL M-3 FIGURE 45
WlRIMG DIAGRAM OF
68
0PAWBAR5
S/ATCHING
TRANSFORMERS
Ti(solO liamuai.)
VIBRATO
TO COMTPOL
A.
IS
LINE
BOX
TO SCANNER
A.
T2(lO*ÊO manual.)
1
PAfJEL
fOCOl^TCO^, PAHtL-
rn^0
_A__^ OiZo
,
fiji
C
o
jfijiFa
V
lO
fffl
2
OJ
yf
n OS O'
^ r
i>
r.
WH
-o
VI
GV
ro
pi*
75
^'cT^
TO AMPU^PliR
GN
ÎQ
Pi^^^
-V
^1
PECj-.L
th:l
gh
VfH
RED
rEL
f^^.
Cy
BK
y
:--"^'^v^'-^-'^-'-^.v='=---?--V-'---:^'^v^::^-^
DPAWBAP
M
TO SCnEOATOVV
r-^T^v'^ ^'n^g^:
'
>.v.v7j^:?.
?co:j<-:^5'
r
a o
SOLO
le
7S 7^
5?
SI
29
25
VVAKiLiAL
BUSSARS
'SCAMWfR IMBEH5
er
'f
Bn WIRES TO Vitt'^TO LINE g Qf^ WIRF3 TO SCAr^vjcB,

/
n
.14
f
6'
sf
4?
i?--'
^
L TD V16RATO
Ll^JE"
I
^-ÊL
9K
Clio
GN
i;x>'^
9
.fl
'>'"VIC
-'7"
V*.
NUMBERS "
FPECuEMCY
6 O & i O 6 6
6oo
74
OÔiOCooobooooOoCHi^
52
O'liicio
Si
oCicioOoiibOo 0666
1
60600006001
^S
(B
LOWER
M^frjLTAL
T5
29
;^
3
VlGRflT^ LJKJE
BO*
TO AMPLIFIER
Qn WlOES TO
VIBPATO LIME L
CONTROL PAMCL
CflEAP Vl^w
'/(ITH
COVER removed)
COWTRCL
PAMEiJ
.^^-^
"^
^0
JUMPER Wines
C:;^JNECTSCAMN0 T^RMINAL^ OF
H
GflA*'
"= 0>jT<?0\^ PANEL-
7
c
iV
.
&I_ACK TO CO'yTPCU
FftNEU
Bft
% 5^X ? 4\
5^ME NUMSERS
*za
71
^
6C6
'890
fitB4
^3^
BN
4fi
*
^3'^
cL
K^
-t
rk
Al'^
jM'
A90
aio 7z
700
5TC
6&^
gr
NjREL)
9
\gN
9 D
I_J
a
jWH
.YEl.
;gn
GN
^
BK
678
65<v
5ai 659 67t 051 6e
dST 674
oif
CbBO
679
6S6
o<9
66-1
OfeO 077
osi oaz 029 Q5
-^^^6
375
Qio
6st
OBO
fbSfe
^73
OA^
I '
VUH
rEL
61&
06
0^
^11
oaa o*
o^
ozfc
oi
o^
Oil
<^2i
Qi7
03
02n
96
i_
prRCU55^0N SWITCH
^
^ _
P'e.^
a>^
VIBRATO LINE 30X
ÊAP VIEW
vvjTH COVER ^^Q-iÊp)
GEMECATOR
VIBRATO^ SCANNER
"---^^rsv.
.y-^\ y.-.^:-^-.-.
^
.^^-.--.x
v .-.-.-^-it:"^':^--^.1^,
i^d,1~
'TT^'
^"'^^:'
^'
--'--'J -'TX'^x-^".:
:\:
^x^ j:gj.v^--:-'.'.T-L-:^:z:s-z; :s:^.skki3^k^v
COLOR COD
H^:
"rum'
'start"
5WfTCH
Switch
3N
SPEAKER PLlG riTS RECEPTACLE QN AMPLIFIER
^^
^
E2r
TEL
4
CUTOFF
n / Df
o
"T
PERCUSSION
5N
GT
BK
&K iSL
iBN
BL
V^
LINE
PAhiEL
5^^
GN
6
Gf
Tl
BJ
GV 6L
BfJ
:^
JJJ
a7 \a
1^
b^
N o
'
kI d
mi
H
il
F190
YEL
BN
FIGURE *^& SCHEMATIC DIAGRA.

M-lOO SERIES WITH AO-35
AMPLIFIERS: AO-29
>.
POWER SUPPLY
FIGURE 46
70
fliU fliO
i?2i^ MANUAL
I
AMPLlFjtLR
irjTERMEDlATE AMPLlFlElt
[-^L*lNr7eff 30CP5-^ C 13 if-OOOOi
(A^
^9-9t USE
This C
MATC"INS
! I
12
SAlN: 79k30CP5'
EJlPHEiSlOM
OUTPUT AMPLIFIER GAfN 'US i30 CS

.0000Z*-.O00D3O
Cir
CM-r4NEL
GAPl^=33ei30CP5
-C-^
CONTBQL
"26 CiO
-f
C20rf .O0000
LOUC
i a:^ 7
-AW rooo
50 V
N-40 V
ooaiJ
^r^^ ^t.1
IZA'J^
C
90
CZ^* '.0*7
305 y
PILOT
nCUH
XvJj
BJS "
.2^'rtEa.
"^^yV-V^^
Ki&i
.33
sc*fi<
J3A.
iWt(j;
.0C2Z
1*1
T3
Jl
|JP"CH
-StLECrCD AT fACTOJ^Y TQ
6Al,*NCt
GAJN" 9S
'g
^95
,1
Hlfi-
/-
IIIMIII
i30
Crs
-00
2
I
XDOOiG
_VWW* vww*
re
I
^3
J ^
M6,
SVW
svvv-
C3 l.QOl
i,7MEj.
1
Û
4+'-*ft
^J
viapukTO
R5 '000
*
7a
jl
^ T
ViA
I
^^/^-1 .00
303 ^
USE
tîiS CJRCUiT
1
I
^ J
CAMCtL"!
w ?
MANUAL
-AV^
T
'
-D:mI6V'B=*TC CMA^JNEL / -MA^JNEL
iNP'JT
'
PfDAI- SliJMAL
/I
XQ-^
-j"''Er.
AWPLjFlfft
Awe-^*1
CLAHIXET
6+^H5'
r^RCUSSION AMPLIFÊR
^4TME
:o*7
IL' C.^
JEH
SEtTlOW5 C*N at OfPflfi^tD ATOM! TIME
1
-
EZ-OOO
\
mi7
.030I
JÊiFtER VOiCEl
P4a 3'
NEÊ'fB
11
SCA/-NEB
ris7
moc!:l^k R-UîH
a^sv
zcs
tJI
-lJOJ
MAlMUAt JU5BAR3
ff>
-^
^V-ZyV-.^-^
î^
1*43
o^
J9 liAU7
II
'>o
cw
.t;. rt)0L2 !jgMf6
AUOUMT OF VIMA'D
"
14J
^
ft- HJ
"'v^V^-
VOLUME
USE
iAi^* 5 ^C-
S ^00 CP&'
5E-U,
t;ed *r i-^cTcftf
a
iMALL
^t*
'^^^
O ^
U
.LOW Eft
^
,
&Air- =
-*.i
'
IP
"4S
C26
,004:
r Flutes
CUT
0F
6QH '-t'<^'tÂLS
^StT Of NIN? :;C^J TACTS U TyIîCa. Pi_AY-N&
KEY
SFCTlONl CAN Bt DtPÊliETJ AT OîE TlWE

1.5
wee.
^9=.,.
-V
.COS*.
aooj .005*r
..
'C056T -oos^r .ao5*r
.ooiii
-oossT ,cos*T 0056

.
.0056
.OOSfti
OOSfi
.COi/
J
<-r*sT
[:-:c*f"
3î
rJ
;iBRATO HA5E SHirT LIME
.T^^:^:^j
Yt
II
4.
celeste:
PEDAL
(
"
celz^-'ezi''
no
i-rAUMCMiC;
I
1-'^'
|*S"C1J5S"0M
POWER SUPPLY
IlOT LICHT
5A\H= 3a 30 C'S
.*'MES
"FfUM
KM3
r
cea OFF
,BL
^SOO
ClflOOO
f<l
i3-*v)
ro ^NS
>^'^
T7
PEDAL AMPLIFIED
VIO
CSi,..Oi
PEDAt tABLE
C55
.0001
ii
R90
'lAii
STAHTlhG
WuTE'
^40
WBAI HITfB
Mfl*.
u=
SV
SWITCH
MoroB
fiODO fQK
SVNCMKOMOUS
I
AOTaB
NO
PEHAI,
ANY 'EOAL
'"tSSEO OV
*P<tSSEDlV
177MI4'ET^ fM 4 >liH^
f3Z
S7a 5
T3
'^14)
I
C70
ft77
-AArVV-
-11 61
'63
-WÂ
lAl
'.
'flS
T7
i700
'JW, w-rVW-/. I5f&i iifhiCj
3OMO
5 'tCL
J>CIJTCIE'
w
'CDALSJ
ED't SlG^'Ai.
CONTACT
OE UAST
-PfÂL KEVIHG CONTACT CLGiES AiHEr^ ANV PEDAL 'S =1CS5ED A-^ T^F^
;
PEOAL SiGnal CON'aCT OPEnSi and OPC^.^ WHEN PHrÂL iS AELt ASEO.
H
intermediate: AMPL^FiE*
f-^-&A'Nr-
r
Tl
RZC
LfPPEP
MANUALS
OWES MAVJUAL
JON- VIbfiATO
AM^LinflEft
OUTPUT AMPLiriER
U- GAiS- 7Sl30CPi
CONTl*OL C20r ..CfOOQiC LOUD
GAIN lie 130 CPi CZ3|j_f^5T AT FA CTQFty
-
CHANNEL
IMPUT
W^/W\*A I0ME6 3-3MEe

G*.IH>=
I
7ee
I3C
CP5
Cflif 001
1
I
|_,_|
Xi
mg
93e liDCPS -^ vz. 6Au6^ ' SOv
_J7Mf6
7^'
.01
C'6
:.5
fits
V
r\
V*B
i2**
7
'
.OOOOl^-.DOOOBO
F-40
son
Cf3
H .01
'2'AI-/'^
e_
CL*J J.O*7
ME&
*fl-9i USE Tii CIRCUIT

I
6MES.
(U)
AT
> P3I .33ME6
^000 LZ
.00021
^-^^-'
I'i^
^WA
R32
.ooi:>6e
flê^ RasA? (7!-^

OOiE
ssv
'
2^
SELECTED
j600
FiMlOHV TO
BALANCE. CHA^JMELS
ft3*
6B0Coi^ 6&000
P35
'^
RADIO '
*L5V
(FROM V4a1
BULBARS
fHONO
5-6 ^^L6
1 t^
^:^
4* -*b USE THIS ClBtU'T
LL^
ÂWS"
B7
Rfl
&AiN^ 35
e dO CPi
C3| j'OOi
C (7
ClB
_0OI
I0wr6.
V^W'
i.7MCG&.
CZ5^
-047
'
cancel"
UPÊR
#
'
VIBRATO
/*7000
yiBBATO
IHPIJT
/, SiMt6^
30ev
MANUAL
CH^NNCL /
/
,000
+ So
P50y
PEDAL i6NAL
tL5
KDOaoaceoo
-=:Mtn
^-fe^
pii .;7 WE.&'
^
iCJ-^^'i
IHfUT
rrt
J
I
^
SPEAKFTR VOiCEl
*
PRCU5SI0N AMPHFIER
.33
Â^^'^ *7HE&
DMUV DfJE Of TnESt SWITCH iECT'GN5 CAhJ 6E DEPPf^^? D ''
OfiE
JH
i 22COO^
Si4
i BiE 5 2.^000
COl:_S
16
TiwE
T4.
p4a
CE
W9
riiAU7
H50V
Tfi
AMPLIFIER
ftEvClE E
DU'PijT
Z <
WEvtwB
I'
MANLTAL
LOWER
^
4
>-
-^
K'ODl*^'\ P-UN!1
G-S V
m
J
C30
^r^ 25
+ IS
R4fl
-J3
ZO0
AUOUKT OF
VTEflATO
-I "^ EC
6E:^[RAT0ftS
ifl -
*'
VD_LJWE
SOf T
^j
USE
6AIN
50C e 500 CPS
^
Â
M = ^_S G CPi *^'Z-0
I
StLgCTIG
>T FACTORY
T_P.BlA^*^NCE
C"*NKELJ
SMALL
<
>^
ij^
(6flfc*-ooty
r*<cuiSfaN 9 i CUT Off
Ml
!
A^
C43_L
-oas6
^n
3:
FUE
r^?:::; ;?mE6
!
CZ6
-00-*
!^
^^^
4;=
.vi5A_"_LiNt. ECl TfHWli^*^_i
U>Êft TVPICAU Pi-AyiN6
KEY
'iTCH/' DHL* DNf Of THESE FOUR SW: SeCTiONS CAM fcE 0PtLSD AT OhiE TIME
3=*:
i'
^..^.
iOC
1466
.
C37
ôcrfcT .OC56
C*0_J_
C36
-00^6
C4iJ_
.005
C*y_
.0056
C4*__
.0056
c-â
C49
C0_
ry ""^
^V*V-
*'00
pmcj^sioK
R5& Z000'33
ft53
0OSt\
.0056
.0056"
.0C56
.00561 -OOSt
'FAST DECAY'
5-:2
1^
1^
VIBfiATO
PNA5E 5HirT LINE
"105
^TO B
OUTPUT
^^:^^J
\^
!r~Riio
CELESTE
'
CELESTE
"FDA-
7*E RC_i;5lON
[;KArt&Aii
HARMONIC
*
l^
r*
6ain= 30 S
viO .30
i^12'
POWE^R SUPPLY
RSi
ftlsiST^R ('=^^0)
PILOT
L^MT
li^
CPi
.47
**E6.
^50C
(IBODO rc 234 V
TRANSFORMER
T7
C6S
PEDAL AMPLIFIER
CS9. .tDi
-.--<
-^C6*
',O0M7
ON
T
DV
*|.^ rfSD'
jfi- '-!
<3^.
QPF 90
iTAPTlNG MOTOJl
CS3
-OOOl
.C5& S^^
'EAJS ^JTE'
^_g.
5WITCH
GV
-o-
fkOOO
5VNCHK0' NOUS MCTOt
.00 if
'01\
PEDAL fÊSSî
i2
kO
PBES5ED OV Arvv pe:ial PIESSEDIV

PEfiAT.
Q
s T
rfn [Trio
T3
T7
"
C63 C65 CSG
Vft
(w^
(vl
MOAL il&NAL CONTACT
0'
LAST
Pt&AL
v6
WHEN ANV PEDAL l PRESSEDtftf TER PEDAL S^&^JAL COnTaCT OPEMSJ an3 OPENS WHEN PErjAL 'S ÊLEaSEIX
KEVINS CONTACT CLOSES
w6
<o
73
U^ji~)dkvir 4-
dt
0^
<
Oh
in
u
(3
75
NOTES
76
THE HAMMOND ORGAN SERVICE INFORMATION

M-IOOA SERVICE MANUAL
SUPPLEMENT
HAMMOND ORGAN COMPANY

77
M-IQOA PRESET PERCUSSION UNIT

adds five pre-voice percussion effects, including reiteration in three speeds. It also provides three percussion effects, '^Normal (Non-Vibrato)^', 'Vibrato", and "Delayed Vibrato". For therhythm accompaniment it also provides a "Cymbal -Brush" effect, the "Brush^' being on the lower manual, and available when played in a legato fashion each time a key is depressed. The "Cymbal"^ is available on the pedal and sounds each time a pedal is depressed. The ^'Cymbal-Brush" control turns these effects on and selects the "Cymbal-Brush" volume.
to the
When added
M-lOO series instrument,
this unit
SELECTOR SWITCH
With the "Selector Switch" in the "Drawbar" position, the signals from the upper manual harmonic busbars are routed to their proper drawbar in the upper manual group. The following is a breakdown of the harmonic switching used in this kit;
HARMONIC BUSBAR SWITCHING AND REITERATION SPLIT
UPPER MANUAL
The Sub-Fundamental, sub-third and eighth harmonics are not switched. The sixth harmonic busbar is used for percussion keying. With the "Selector Switch" in the "Drawbar" position, all harmonic busbars are routed to their proper drawbar.
REITERATION SPLIT
ir
A A"
tr
CHANNEL
Znd 3rd
4th
un u B"
CHANNEL
DRAWBARS
Fundamental
Chime
(5th to Freq.
Div.
(1-1/4
From
Freq, Div.)
Guitar
Fundamental
3rd
4th
5th
2nd
Marimba
Fundamental
2nd
3rd
4th
5 th
Xylophone
Fundamental
3rd
2nd
4th
5 th
Banjo
2nd 3rd
4th
5 th
Fundamental
78
MODE SWITCH
With the ^'Mode Switch" in any of the reiteration positions, the harmonics necessary to produce the "Chime'^ ^^Guitar", and ''Banjo" are all fed into the "A" reiteration channel only, while the "Marimba" and "Xylophone" effects feed harmonics into both the "A" and the "B" channels. This split into the "A" and "B" channels only occurs
with the use of reiteration. Without reiteration, all effects are routed into the regular percussion system. The two reiteration channels are identical. You will note that across the secondary windings of the two input transfornners is located a fieldeffect transistor. The gates Q200 and Q207 are fed alternating pulses from a bistable multivibrator which supplies alternate pulses to each one of these gates. That is; one is on, while the other one is off. These gates shunt the signal to ground, thereby making the channel inoperative. These individual signals are further anriplified by a one stage transistor amplifier, Q201 for the "A" channel, and Q208 for the "B" channel. They are then mixed together and fed to a common amplifier which in turn feeds the percussion output terminal, terminal P on the AO-67 amplifier. The multivibrator which supplies the keying pulses for these two gates does not run continually, but rather is turned off and on each time a key is depressed on the upper manual. The multivibrator consists of Q205 and Q206. Q202^ Q203 and Q204 provide the necessary switch pulse to start the nnultivibrator.
NOTE:
Whenever
the reiteration is used, section of the AO-67 amplifier.
it
connpletely bypasses the percussion
With the "Mode Switch^' in the "Normal", ^'Vibrato", or "Delayed Vibrato" position, the various pre-voiced percussions are routed into the regular Hannmond percussion system, in which case these percussion effects are now available at the percussion output terminal, terminal P on the AO-67 amplifier. With the "Mode Switch" in the nornnal position all percussion voices sound as nornnal, that is, they have no "Vibrato'^ With the "Mode Switch'' in the "Vibrato" position, a portion of the signal available at the P terminal is routed through an isolating resistor into the "Vibrato" input terminal, terminal '^B'' of the AO-67 annplifier, so that the percussion voices appear with the "Vibrato", In the "Delayed Vibrato" position, a portion of the signal available from the P terminal is routed to the base of Q214, It will be noted that the emitter of this stage is not bypassed and the output of this stage is relatively low. During keying, after a predetermined tinne lag, Q210 and Q2 11 turn off, and Q2 12 and Q2 1 3 go into conduction, thereby placing C211 across the emitter resistor of Q214, This materially increases the gain of the stage and as the percussion is dying away, feeds this amplified portion of the fading percussion signal into the "Vibrato" channel of the amplifier giving a "Vibrato" tail-off "Vibrato" and to all the percussion voices. Two positions of the "Mode Switch", "Delayed Vibrato" also effect the normal Hammond percussions when they are in
use,
FREQUENCY DIVIDER
using the "Chinne" effect, it is necessary to create a 1-1/4 harmonic for the proper reproduction of the "Chime" tone. This is accomplished by routing the 5th harmonic into an amplifier made up of Q227 and Q228. Q229 and Q230 rectify and further annplify this pulse which is then fed to a two-stage frequency divider, made up of Q231, Q232, Q233 and Q234. The output of this second frequency divider is then routed back to the "Selector Switch", and is used as one of the harn:ionics in
When
the
"Chime"
effect.
NOTE:
Because
attempt
tortion.
a
to
frequency divider can only handle one frequency at a tinne, any play two or more "Chinae" notes at a time will result in dis-
79
CYMBAL AND BRUSH

The "Cymbal-Brush'' switch when in the "off position disables the keying functions necessary to produce the "Cymbal and Brush" effect. With the "Cynnbal-Brush" switch in any one of the "on" positions, the 8th harnnonic of the lower nnanual is disabled and this harnnonic busbar is used for keying the "Brush" effect. The pedal keying contact is likewise switched into its proper keying circuitry so that it will activate the "Cynnbal" effect each time a pedal is depressed,
BRUSH KEYING
With the "Cymbal-Brush" switch in any of the "on" positions, the base of Q217 is routed now to the 8th harmonic busbar in the lower manual. Anytime a key is depressed, the base'voltage of this transistor is routed to ground, and this stage stops conducting. The attendant rise in collector voltage is innpressed on one plate of C217 and on R262. The other plate of C217 responds by driving excess electrons off to ground through diode D204, the resultant positive voltage is then fed to the base of Q222, the "Brush" gate. To the base of this "Brush" gate is also fed the noise from the noise generator Q218, This noise is nov/ tuned in the collector circuit and fed through R279 into the "Cymbal and Brush" amplifier section.
CYMBAL KEYING
With the "Cymbal-Brush" switch
the pedal keying contact in the pedal switch is routed to the pedal control terminal, terminal "S" on the AO-67 am^plifier. With the "Cymbal-Brush" switch in any of the "on" positions this keying contact is transferred to the base of Q216. Q215 is connected between the pedal
in the "off" position,
keying terminal, terminal "S" and ground. With no pedal pressed and Q216 con" ducting, reverse bias is supplied from the emitter of Q2 1 6 to the base of Q2 15. Each time a pedal is depressed the base of Q216 is routed to ground. With Q216 not conducting the reverse bias on Q215 disappears and forward bias is supplied through R255, Q215 now conducts and routes the pedal keying terminal to ground. With Q216 in a state of non conduction its rising collector voltage is impressed on one plate of C219 and on R216. This rapidly rising pulse is fed to the base of Q219 and Q220. Here the pulses are sufficiently amplified and fed through the diode D203 and on to the base, of Q221, the "Cymbal" gate. To the base of this "Cymbal" gate is also fed the noise fronn the noise generator, Q218, The collector circuit of Q221 is tuned for the best "Cymbal" effect, and the output of this gate is coupled through R281 into the "Cymbal and Brush" amplifier "sec tion.
CYMBAL^BRUSH AMPLIFIER
&
NOISE GATE
The "Cymbal-Brush" annplifier section consists of Q224 and Q225. The output is taken from the emitter of Q225 and fed to the volume switch. The output of the volunne switch is then fed back to the noise gate. This noise gate, Q226, effectively shorts the signal line to ground when neither of the "Brush" or "Cymbal" effects are in use. R261 and 262 feed a positive voltage to the base of Q223 anytime that a lower manual key or pedal is depressed when the "Cymbal-Brush" switch is in any of the "on" positions. When this occurs, Q223 goes into conduction, thereby depleting the base voltage applied to Q226, With Q223 in a state of non conduction ("CymbalBrush" not keyed), sufficient base bias is supplied through R287 to the base of Q226,
putting
it
into a state of conduction
and thereby shorting the signal line
to
ground.
SO
CHANGES A^m REVISIONS
Referring to Figure 56 of the M-IOOA Service Manual Supplement the following components on the schematic have been deleted. These four components will be found in the middle and lower portions of the Brush and Cymbal keying circuitThe following items have been deleted: C-218, R-265, R-275, D-204, and try. C-2A3The following component values have been changed: R-283 was 47K is now lOK; R-285 was 470 ohms is now 100 ohms; R-296 was lOK is now 4-7K; resist or R-279 which was selected is now fixed at 4-7K.
Two Zener diodes, D-209 and D-211 in the power supply, have likewise been eliminated. D-209 is now replaced with a 68K half-watt resistor and should These changes alter the voltages available from two of be designated R-325. The tap which was marked +91 volts should now the taps on the power supply. The supply previously marked -12 volts should be changed to read +80 volts. On the schematic diagram, Figure 56, add a now be changed to read -9 volts. Designate this component 220K resistor from the collector of Q-213 to ground. R-330.
NOTES
81
Dd y^
s:
-< DJ
'-'
FIGURE 54
84
SI
PEggâ fM
FEîciiMiw siwal our TO -fc7, TERMINAL H
TO PRAuBAlt
swira
MOC SWITCH
^M ''f
,.
,.'*
'-i^ît
FUhD.
TO
DâuBAN
TO DDAUaAR
3HD Hnwfwir
TO
DROWBM
4TH HflRWNi:
TD IJltlUftiR
ITU HMM04IIC
TO CrttAWÂN
?0 jL3-fe7.
TrWlMflL
TO
Je-fc7.
7TIW1N4L
-*
Hate
5
CHANGES
IN
L>iTR PRODUCTION:
Pairs Eliminated: C3ia. C243, O304. 0211, R2e5, RZ75. Parti Aaaea. R330. 2?0M. Tfom Q213 collector lo gfound. Paris Ghangea: R325, SaK. irt olace of D2C9
TO
47,TD*.KPEPC.
KETlWi}
-*
SI P05(TlCh5
1.
R279
R2fi4
Fi"fld it
4?K
'liv Fon
Ofims
s
DIIHFS
DtiWfllRS
UJITIhB
Naw 33K R2BS Now lOK R3B5 No^ lOD

R265 /io 4,7K
All
^flres
)f
ÊiTcÂtôN
2. 3.
-91V
ii-iei
no^v -fiOV, All
-12V
Ujies
now -9V.
4.
5-
MMIMBA
XTLOP^WE
BAMJO
l-l/j HAR^'ONIC
fOfi
i:hJ)'E
sih Haitf*onc
FROM ao-b7
FROM fiO't7
Q
SI
flPUSH A
-fOo.LJOf jm;
SWI
'^riLfs.
WjIO
SI -
I
CrMbOL
TCH
uv
\'
* I
101
; OJI
en
TO OfiE^k^d^^^
1,
'
CYMBAL
5201
iWiHtal
rv ^HAÔM;c,L0UiT
HfiMLftC
]
tfl
POÊH
TD
iUPPL'
flO-fc7.TEfln.-^'',PED0L
(fr iHQ
âafc^
ÊOW. tT!HC C*IT*CT
tCTES.
T,
ALL
2
i
UHLES5 OTHEftuiSi SPECIMEO, fiHt 2r*35b5 fiLL StSISTOflS, U/^LESS OTHEBl-tSE SPELlFitC, ARE !/? WflTT Sk TCHES, 5H0Wi tf CIRCUIT SI i -OF'" .POSITlOU; %l IM 'ÔRHflL- POStTJONL
THlNSiS^GflS,
*
i.
ALL DIODES,
SI ^N 'Dfrflt.bfli'S" posnion. UNIE5S OTntRk^lSE SPE:ifrEQ, iPE I'-J^b.
-^
1HF|
,, 1311
^.
CH*-<L
l-T/a-
HflPHONlC
E N
fi
ft
\u%
NGISE GATE
&
_J
fi-
BUSU
CT-3J1,
KETtKO
l:*H i
JTl-biL OUl
FIGURE 55 SCHEMATIC DIAGRAM PERCUSSION PRESET UNIT
85
r
>
a
r
WING
MANUAL
UPPER MANUALS
LOWE?* MANUAL OP AW BARS
^\
AMPLIFIER
'^*rci-iJr-*6
INTERMEDIATE AMPLITIER
OUTPUT AMPLIFIER
W- GAIN739130 CPJ
EXPRESSION COhJTROL LOUQ
CIS
MON -VIBRATO INPUT

\~^
fiSI
KZZ
Cfli' OO]
I I
CI3 W-(10OO2
G*IN:i3l3a CPS _C23Ur^5^T AT FACTQRV

,o:iooE*-.ocao90
I
&CKJERAT0H5
-g-gi USE Trt|5 CI'^CUIT
SAiN^93i3i30CPS
H>9
VE.
CZOi ^.OOQOZO
J40 V
A*
6Au6
liOv
R?6
r\ SOFT
JME3
=^^1 .33
--îir.
flra
JC7
0
i>/E6
tf.S
$-Ar-* ^
,-
.30022
.^V^
IJO
+-L5V "=5^
.oooea
fl3d<^ ff33A5
-i?-^
35VI
FACrOflY TO
I"
^
^*
5600
1*IANCE
llHASfftJELS
sacoo:
CI7 .0021
:
RADIO " PHGPÔ

? H3S 5.^'ÊS
l
*L5v
(FROM
V-*A)
o
-i-Zô
fv*l
VIBRATO
lL.^-i-_-^
CANCEL LOWEI
MArîjAL
,
35 R7
VEIi-
SAJN= ^5 ^ '30 41*5
i^îfe H(^
W3
OGO^D
C3|/-o6l
-001
Z.7rM<E5.
ftENE'A"âH5
THIS ClRClifT
^ 1 = ?
1=
VIBRATO CANCEL'
VIBRATO CMAr^NEL
^,
4
-VA\V
imPUT
-^
-'
PEOAl i.&NAL
^0
-I
^
I
-^
^VvÂ^-
Vv_H_U_*_-__L
^Ê
"^
uR'JmFEt'
^
5P- AKE*? VOiCE
IfFuLL iîPGAh"
PERCU5ilON AMPLIFIED
[in
|T
COIL3
G
"ACr-J
0-WS
QNLT :iN Of 'HESE SW.TC^5ECT'0N5 CAN BE 0E^SS5D aTOME
AO-SH AMPL^îER
iME 111
< z
5
4r,UAL
/5CANnE^.r T J
1
flEvt^TB
"REVEWr
ENPJT
^JT^-J'
o U J*
D
M001L4K R-UMT
n
3
^C
u^
"'AN
1
AWOONT OF
vl&R*TO
"
C^l-
> ^ -I
SflVERATO^tS
10- Hj use THIS C.RCtjrT
VOLUME
5orT
"
<
>
<r>
r
:T0FMN6CflNTACrs
UNDEfl
^.
00 CPS
I Y 1_
P-5
CZ6
.0D47-L
fEftCUSSiOM
tL
r--
22Ê&
CUTOFF
OI^Li
ONE
:>F
'l-lESf PSUfT
flE
i^'"HX
ONE TIME
TYWC*lL PLAYING KEY
SiCTiON? CAN
DEP'E!j5EQ A"
p
PC
<;5a).,..,6.,6,_3
iflOO
LiO
Tr-T-TTas7
"^
Lr
r^
LI5
L6
'66
1.
C37
fiT -0OE6-
3fl_
t!_
c^sL
.0056
c**!_
-00 56
I
c*7]_
.O0S6
"*aL
cjosfi
I
h3-
.
-:>
aooo'
.005
.OOSST
Ôf>5S
-cotr
PEFICLJ55ICN
izooo:
+33
TES'îNAî
T ^=^^J
RfDAL
VJeî^TO
PHA5E 5MIFT LINE
"CELESTE
I'
-tLESTEH
'
t?
MiftC
^WCUSSiCN
I
RÂJAH
POWER SUPPLY
HEATED
R3I -VA--A,'
Tt
-500 9
PIN.';
^^^^^
4500
NJCU
+
HAS mGn iC
- ,,--n\
[lîJOO -OR I
i34 vj
TBANiFOPstES
TO
'SAJN^ eO 30 CPS
PEDAL
PEDAL CABLE
AMPLF
.47N*E6.
.0003
L
* HEAT HEATEPi
1^4
J'
*3S
E^
,00047
X
CS5
.OCOl
C56
oa
'lUN 5WITCH
ON
^*'.->
r.^<>''
î-f^î
5>s
^^li?
u
::^c5a
Too?; "Jr
250 NO PEDAL "ESÊG Lz^V
"5 TART
SV^lTCffiV
^90
(1000 rCH
I
NO PtOAL "VESSED OV Ar*y PEDAL. P^CiSEO IV
R7a MEG.
STAPTJ-^S
SYNCrrflO n
335 V
C6A
^:^'i50
-k r:c6s
MOTOR
NOUS
>OTCl
r!6l
.00 E i
K335V
ANY
33
î3*vj
'E:Al ""^Sê:
C3^
C6?|
I
TS
C&3
R77
-WiA"-
I
_-AVA
3-3 Nf^
65
85 30000
T7
Cfi6
o
u^4
P* & PE3AL SIGNAL COKTACT OF LAST
E F
*:ôo
;aME6
>>cr, p?::iAL
CST-x
-^7
i
w
PtCAUS
T'
CUTOFF
"
^P^DAL 'KEYING CCN-MCT CLOSES ahEn arsiv o^DAl 'S PfÊ^3tDv^r^C=*

PFDAL Sl6NA'_ CONTAC^ OP^NS) ANQ GP^'^S WHEN PEiÂL S Ê_EaSE!^.
"EDAL
UPFt MAh,iJ^L
rtD*l
BI^^ ^
W] jNEVEtA
^laAATDT
rVJBRAlO
r^KRilTi;^
hUAATV
LfiflK
fl.A
ptM
auiSi
".una
pA*
k:iaS^
ffLLSTr
CHOfllfl
Umall
AS3
MliT
FWT
MCAT
,ttA:Oi
bltAWÂU
CONTROL
r*rHfL
3N EK
SN
6L
C?T
&v
VIC
s.
SS5^
??WS5
n
&N
_B^ ^4^^^N
f.
BK
#N
n^
I
htc
BK
t*i
I_L
TTT"
SWITCH
IV
SiMTC
OFF
1
O^^
5
a
^
^ L
Xgv
;i^ sa?5.^
S
Tr
V
^-
VIBRAtG
LlÊ
CABLE
^7
5Hinr>rD w^nf
QO CXOGOOq
^'-^'''_
t^
Crj
^^'
lh t^âp^^^^
-.
r
WH
T^/^LOWtfi^
MATCHING
MAN UAL
WH
VIBRATO
SCANNER
CABtE
VfSRATO LINE &0X
T"
BL^kBL
*vf1 f
V)6f2ATO
^<^
lul
h-i
u
t
T"
II
1
i
D D
irn
ft
ODD
i2
nil
11
iS
2C
MI
MANUAL
1 t ,
3MJELDEC
y^\RT.
^3 WJRE^ Td\
T
FffECUf.NCY
MATCmN'j TRA^SÔ^l^fcR
ZtkBLE
3
I
44^ 'i-
ra
HI
i>
I)
c & 75 74
^ 5Z 51
iiîiao
'HMPfltt
ZS
2fi
rn
MANUAL
I
7-sr\.
Jfi
i!:
VIC
5=
r2
PILOT
,'
^T
GETN^fiATOR
5a^'
Ifo
LAMP
OHVL*
l:
YEL
POWEl LINT w*eL

at
78
rk -ff^=-ir
fl^
&K
aii
**
O?^
fa
5^
Bi
Ii9i6 ife
*0Z<
fV 74| io 7% *//* 9J6 Zjiso T/ofeîlZ 2 PISO
W6B
T^
ii
7e
i'
&
73
*5jrH
fRfpu ENhCY
'4=
sîr^î^
L^
l!Li^^^
TO ^-OLUME SOFT 5W. son
7 ^
<==^
Yj^f
AMPLIFIED
D
iL
ni *t jsNt^ôv
"I
J^t
AO-67-1
n
H
,
.Xyi. ./u:
22z -^ i^ z
^^!^^Zr4_L_
o o c g p o
KU
6T*HT
VWlft
CTTJp\ p
A*'\i_mHMij
01
flSjlâ^H
MOTOR
TIL
3UPPL.T
aMPCf FjEt^
Ch^B.^'^
HM^T]-'
^R-Z0 3
^R'ZO^V^
WirE'SHlLOEl
\c-Zo
^
^îh
V~
-0
fl-Z89
B 'CH^^NEk. if^Pt/T
Hî^2H
/
HI1>
r^p
r-ôo
Y
'*"
^rîp
^-zs-ei
>-fcTi?V-
M53S2U
ÔS'
-OI5-'
[ff-ZTzTMMSIT-
BRUSH _t/L-^
oj?fl*i
.^
'-2 '7
3)
1
^
fe
t-ZO(
Mft-3i g I
^4.^3
!
Mff-3o3
[
-^
-t^-306)-*
^^'3QaU
<^3/V
"-fc^Tsh
iz?7,.-
H^^î^h
i
o
P
Bu)
'PCTÛSS)OV To
T
-{ P.-30I
v Y
55)^7-oSkH/rcK
^
1,
+ ^8
H^29S"H
R-292,
rf^PuT
#
WHFTf
SHfCLDtp
=
wttrre
HtSIh
MEâ
-^
^^^^^^
^^-^4(k
-(^^9%
Hff-^38
-*
^R'^37U
-{R^33>
FIGURE 58
PERCUSSION UNITS PARTS DIAGRAM

89
INSTALLATION AND MAINTENANCE INSTRUCTIONS

IMPORTJNT-Wh^n
tion, the generator
the organ
is
set
up
for opera-
appears.
Do
not turn
it
any
farther. This procedure will
should be freely suspended. To do this remo\x four hexagun head screws under shelf, turn four sleeve and washer assemblies over so that washers
probably be necessary
in case the
6BA6
tube
is
replaced.
PERCUSSION CUTOFF ADJUSTMENT

do not fade away or their decay is unusually fast or stow, this control probably needs adjusting. It is a slotted shaft located on the face of the amplifier and is set at the factory. To adjust it, push in
If the percussion tones
down, and replace screws, tightening them securely. Use shims under console, if necessary, to set level in order that generator is free to move in any direction.
are
Failure to do this will cause noisy operation.
The
console back should be at least
14" from the wall to
allow proper ventilation.
Be
sure that the motion of the
drawbars, and push down only the tablets marked 'Tercussion Second Harmonic/' ^'Percussion Fast Deall
pedals
When
not restricted by rugs or unevenness ot the fioor. playing the console, see that no piece ot electrical
is
equipment having a strong magnetic field is close to it. For example, an electric clock standing on the console can in some cases produce a loud hum in the speaker.
This may occur equipment is in an adjoining room close to the wall
also if a clock or other piece of electrical
cay," and 'T'pper Presets-Drawbars," Use a weight to hold down several keys on upper manual, and set expression pedal to loudest position. After about 5 seconds
turn percussion cutoff control until the tones are just barely audible. Do not turn control any farther since
provide the smoothest decay. This procedure should be followed in case the 12AU7 tube
this setting will
opposite to the organ.
(nearest to end of chassis)
is
replaced.
Before plugging
in the
organ, be sure your electric supis
MOVING OR SHIPMENT
organ is moved at all, always be sure that its weight is supported by the case and not by the pedals or pedal mechanism. Be careful also not to put undue strain
If the
ply DATE Of LED
alternating current of the
proper voltage and frequency as specified on the name place. It it is not, or if the frequency is not
regulated, consult your dealer*
on the
legs.
if
Aside from
is
required
the organ
it is
to another. If
tn
no special precautions are to be moved only from one room be moved some distance^ it is
this,
PEDAL CUTOFF
ADJUSTMENT
If
is
important that the generator be fastened duwn to the shelf. Remove and reassemble the four sleeve and washer assemblies with sleeves down and tighten securely. This
will
you
find that a faint pedal note
prevent serious damage.
heard continuously as long as the organ is turned on, this control

is
OILING AND MAINTENANCE

CALTIONiOil
thereafter.
at
probably needs adjusting. It a slotted shaft located on the
end of
first
year and only once a year
face of the amplifier
and
is
set at
NOTE;
Before oiling refer to oiling instruc-
the factory.
To
adjust
it,
set the
expression pedal wide open, pull

the pedal drawbar to
position, leave
all
its
loudest
control tablets
back paneh Use the chart at right as a reminder, IMPORT.ANT: Use only special oil supplied with organ. When your supply from your is exhausted, you may purchase additional oil
tion label located on generator cover or
up, and play, then release, the liighest pedal key. Allow the pedal
dealer or direct from
Hammond
Organ Company.
note to decay for at least 15 seconds, and then slowly turn the pedal cutoff control clockwise
until the faint pedal note just dis-
With the exception of regular oiling^ the organ will require little attention. If any servicing is required, call your Hammond dealer or write to the factory. Always mention the model and serial number, shown on the
name
plate.
RAPHJCS
PRINTED
IN U.S.A.
OMKÛNtCATlONS
HOOO-006059
9/83
300
PARTS ORDERING UJFORMATION
Uhen ordering replacement parts from the Hammond Organ Company, the following guidelines should be observed:
1)
Address all parts orders to:
HAMMOND ORGAN COMPANY PARTS DEPARTMENT 4200 W. DIVERSEY CHICAGO, IL. 60639
2)
orders should specify the model and serial numbers of the instrument that is being serviced. (Note: On late model instruments the model and serial numbers are printed on the tag attached to the underside of the organ keyboard
All
3)
All
orders should specify the Hammond part numbers of the desired parts,
4)
orders should provide a specific description of the desired parts. (For example; Power transformer, 15 volt zener diode, F through B key module, etc.}
All
PARTS LIST EXPLANATION

This parts list begins by listing all the major assemblies (designated) Major assembly breakdowns are then by ^C^) on pages 6^3 thru 6^4on the following pages. ) The listed numerically ( CD (T) ,@, etc. format for which major assemblies are broken down is shown below.
,
<
(6)
Maj or Assemb ly
1
Minor Assemb ly
tt tt ft II
2 3
Component of Minor Assembly

b c
1
ti tf If It
If
ft
II
Sub-Component
PI
*
11 111
II
Example
(
6 )
Lower Keyboard Assemb ly

1
119-000095
Preset Kev Module Preset Key H^dule Key Module
057-054157 057-054156 057-054077-005
37
Visual Memory Cance 1 Assemb ly Spring a Grommet b
060-053454-001 012-028799 04 3-053308
Screw
i
Washer
999-054489 999-000810
NOTES
1.
Assemblies not shown are NO LONGER AVAILABLE - NLA

Items without part numbers are NLA-
2. 3-
Parts listing does not insure availability
TABLE OF CONTENTS MODEL M,M2,M3,M100
MAJOR ASSEMBLY
MAJOR ASSEMBLY FRONT VIEW (MODEL M3
&
PAGE
MlOO SHOWN)
6-4 6-5 6-6 6-7 6-7 6-7

6-7
MAJOR ASSEMBLY REAR VIEW (MODEL M3 & MlOO SHOWN)
(T) CONTROL PANEL ASSEMBLY Cl) STOP SWITCH (TONEBAR) ASSEMBLY

STOP SWITCH BASE
CONTROL SWITCH ASSEMBLY

UPPER KEYBOARD ASSEMBLY
UPPER RIGHT HAND ENDBLOCK

FRONT STRIP
6-8 6-8 6-8 6-8 6-8 6-9 6-9 6-9 6-9
LOWER LEFT HAND ENDBLOCK LOWER KEYBOARD ASSEMBLY

101 LOWER RIGHT HAND ENDBLOCK
lU EXPRESSION
PEDAL ASSEMBLY
U)
PEDAL SWITCH ASSEMBLY
13^ MATCHING TRANSFORMER 14) GENERATOR

15) 16)
ASSEMBLY
AMPLIFIER ASSEMBLY
REVERB AMPLIFIER REVERB UNIT
SPEAKER.
6-10
6-11
in
6-11 6-11 6-11

6-11
(^
19) 2?1
VIBRATO LINE BOX

PEDAL VOLUME CONTROL
MISCELLANEOUS PARTS
6-11
6-12
22^ VIBRATO SCANNER SERVICE INFORMATION..
M-3
Note: Item (ij not used on M, M2^ M3
Note: Item
(T)
not used on M-lOO
M-3
Note:
Item
not used on
M, M2, M3
M-lOO
8.
KEYS
M,M2,M3 SHARPS
C
D E
F
A
B
KEYS
MlOO
CX SHARPS
C D
E
F G
A
B
CX
(18 USED) (3 USED) (3 USED) (3 USED) (4 USED) (4 USED) (4 USED) (4 USED) (1 USED) (18 USED) (3 USED) (3 USED) (3 USED) (4 USED) (4 USED) (4 USED) (4 USED) (1 USED)
025- 036295 025- 035666 025- 035667 025- 035668 025- -035669 025- -035670 025- 035671 023- 035672 025- 035673 025- 032672
025- -042279 025' -042280 025- -042281 025' -042282 025' -042283
025 -042284 025 -0422J5 025 -042286
UPPER RIGHT HAND ENDBLOCK MODEL MM2,M3 MODEL MlOO

FRONT STRIP MODEL M,M2,M3 MODEL MlOO
025-024307
061-020371 051-024165
LOWER LEFT HAND ENDBLOCK MODEL M,M2 MODEL M3 MODEL MlOO 1. PERCUSSION SWITCH ASSEMBLY (M3 ONLY) ROCKER TABS PERC ON/OFF a. PERC VOLUME PERC DECAY PERC HARMONIC SELECTOR TOGGLE SPRING b. SWITCH PANEL ASSEMBLY c. LOWER KEYBOARD ASSEMBLY MODEL M,M2,M3 MODEL MlOO
NOTE:
025'
125
025'
025 025 025
024848 000023 036083 036084 036082 036081
119-000010
PARTS FOR LKB ASSEMBLY ARE SIMILAR TO THOSfi^ USED ON THE UKB ASSEMBLY (5
LOWER RIGHT HAND ENDBLOCK MODEL M,M2,M3 MODEL MlOO
025-024847
EXPRESSION PEDAL ASSEMBLY MODEL M,M2 MODEL M3 MODEL MlOO 1. PEDAL ASSEMBLY M,M2,M3 MlOO M,M2,M3 2. RUBBER MAT MlOO 3. PEDAL SUSTAIN CONTROL M,M2,M3 4. LINK & BEARING STRAP ASSY M,M2,M3 PEDAL ARM M,M2,M3 5. MlOO
043-046347
028-020458 041-020456-003
12
PEDAL SWITCH ASSEMBLY M,M2,M3 MlOO 1. PEDAL CABLE M,M2,M3 Oil 024545 MlOO 045' 020436 2 ACTUATOR 3. PEDAL KEYS BLACK (SHARPS) (5 USED) 025 031469 BROWN (NATURALS) (7 OR 8 USED) 025' 031666 042' 021255 4. GUIDE FELTS (2 PER PEDAL) 042- 020410 5. UPSTOP FELT (26 USED) 042' 031898 6. DOWNSTOP FELT (13 USED) 012- 020972 7. ACTUATOR SPRING
J
MATCHING TRANSFORMER MODEL M,M2,M3 MODEL MlOO
003-021752 003-024498
GENERATOR ASSEMBLY MODEL M,M2,M3 MODEL MlOO 1* RUN MOTOR (ALL) 2. START MOTOR (ALL) VIBRATO SCANNER M 3. M2 M3,M100 4. DRIVE COUPLING ASSEMBLY (RUN MOTOR TO GENERATOR) 5. DRIVE GEARS COUPLING SPRING 6. MOTOR COUPLING SPRING (FLYWHEEL SPRING) 7. MAGNET AND COIL ASSEMBLIES FREQ #1 MlOO FREQ FREQ ?/2,4,6,9,ll FREQ #3,5,7,8,10,
021-035903 021-035137
064-035769 012-031463 012-002345 065-036583 065-033268
fe} REVERB AMPLIFIER (MlOO ONLY) AO-35 (EARLY MODELS) AO-44 OR AO-66 (LATER MODELS) 1. POWER TRANSFORMER AO-35 AO-44 (DOMESTIC) AO-44 (EXPORT) 2. OUTPUT TRANSFORMER AO-35 AO-44, AO-66 3. FILTER CAPACITOR AO-35 AO-44 4. MINIATURE LAMP GE#12 6.3V/.15A 5. LAMP HOLDER POTENTIOMETER 6. AO-44 R27 2K AO-66 R6 IM 7. TRANSISTOR AO-44, AO-66 8. FUSE AO-44 ONLY DOMESTIC 3/4A EXPORT 3/8A 9. VACUUM TUBES 5U4/5Y3 ECC83/12AX7
6BQ5 EZ81/6CA4 ECL86/6GW8
003-024956 003-036756
003-036552 450-040200
016-022885
676-000101 001-021260 016-039512 002-005201 002-012301 002-006700 002-006200 002-006401

121-000046
^7) REVERB UNIT MlOO ONLY

s) SPEAKER
M,M2,M3 MlOO (REVERB) (LOW FREQ) (HIGH FREQ)
014-046896 014-030812 014-024347

121-000053 003-033303 003-021842-003
9J
VIBRATO LINE BOX 1. COJL (LATER MODELS) (EARLY MODELS)
OJ PEDAL VOLUME CONTROL
^ '
MISCELLANEOUS PARTS 1. GENERATOR SUSPENSION SPRING 2. EYE SCREW a. NUT 3. GENERATOR HOLD DOWN SCREW a. SLEEVE WASHER ASSY 4. START SWITCH M,M2,M3 5. RUN SWITCH M,M2,M3 6. KNOB FOR START OR RUN SWITCH 7. MUSIC RACK BRACE M,M2,M3 8. MUSIC RACK THUMB SCREW M,M2,M3 9. MUSIC RACK HINGE MlOO ONLY 10. REAR COVER MlOO ONLY
012-033227
824-000003 060-021751 008-016944 008-024536 025-002071
032-033414
:m

DIVISION OF
HAMMOND CORPORATION
/
11700 Copenhagen Court

(312)
Franklin Park, Illinois
60131
766-6950
REPAIR
A N D DISASSEMBLY
Or
VIBRATO
(A)
a CAMMER O
Check existing switches, vibrato pre-
Although this technical bulletin is based on scanner repair, it is not the

single source of vibrato problems.
amp.
(tubes, etc), phase shift line box, and cables both to and from the
scanner.
(B)
SYMPTOM
PARTS LIST
Syn. Motor & Scanner
Oil Cup Assembly
064-016844
Oil Felt
D
Felt Retainer Spring Screws (3)

Screws (2)
012-002996
Shielded lead and Cover Assembly

H
066-033247 and 066-033248
Brush Lug
&
Insulator Assembly
End Brush Spring Assembly
066-016821
066-016958
846-040314
Brush Assembly
K
L
Screws (2)
Screw
(1)
M
N
Housing Cover Assembly

Screw
(4)
Cable Clip
Stationary Plate (16)

Rotor Assembly
R
066-016829 066-016828 816-080720

036-016747
Screws (16)
Insulators (16) Insulators (16)

U V
045-021942
Front Plate Assembly
Bristol Set Screw (2)
999-002032
W
4
Gear Housing Assembly

Screws (4)
Gear
&
Shaft Assembly
018-033192 and 018-033193
-13
SCANNER REMOVAL. DISASSEMBLY
MD
REPAIR PfiOCEJXJRE
Q)
DETACH MOTOR AND SCANNER ASSEMBLY (A) FROM THE GENERATOR ASSEMBLY BY REMOVING FOUR iH) NUTS FROM THE SYNCHRONOUS MOTOR WHICH ANCHORS THE MOTOR TO THE L BRACKETS OF THE GENERATOR ASSEMBLY. REMOVE THE CABLE CONNECTIONS ORGAN.
IN
(2)
THE ORGAN SO MOTOR AND SCANNER ASSEMBLY IS FREE FROM
(3) (4)
NOTE A. C, LINE BOX^ AND OUTPUT CONNECTIONS FOR REASSEMBLYi

THE OIL FELT MUST BE REMOVED AND THE LOCATE OIL CUP (B) AND OIL FELT (C) INSIDE CUP. REMOVE COTTON THREADS UNWRAPPED FROM THE FELT BEFORE SEPARATING THE SCANNER AND MOTOR. 'DO THIS VERY FELT RETAINER SPRING (D) AND LIFT UP ON THE FELT TO REMOVE THE THREADS.
CAREFULLY TO AVOID BREAKING THE COTTON THREADS).
AFTER REMOVING THE THREADS FROM THE OIL FELT TAKE A PICK OR A PAPER CLIP AND REMOVE THE THREE THREADS FROM THE ONE SIDE OF THE OIL CUP BY PULLING THEM THROUGH THE HOLE THE CUP, THE THREAD FROM THE OTHER SIDE OF THE CUP NEED NOT BE REMOVED.
(5)
IN
REMOVE THE SCREWS LOCATE SCREWS (E) WHICH HOLD THE MOTOR AND SCANNERÂSSEMBLY TOGETHER. NOTE: THERE IS A GEAR ON THE END OF THE AND PULL THE MOTOR AND SCANNER ASSEMBLY APART. MOTOR SHAFT AND MUST BE GUIDED THROUGH THE HOLE OF THE SCANNER HOUSING TO SEPARATE THE MOTOR AND SCANNER. BEFORE REMOVING THE COVER REMOVE TWO SCREWS (F) FROM THE REAR COVER (6) Of- THE SCANNER. THIS WIRE IS CONNECTED INSIDE NOTE THAT THERE IS A SHIELDED WIRE ATTACHED TO THE COVER. REMOVE THE COVER AND TIP IT BACK THE SCANNER AND THERE IS VERY LITTLE SLACK IN THE WIRE, LOCATE THE CARBON BRUSH AUDIO PICK-UP ASSEMBLY (J). CAREFULLY SO YOU CAN SEE INSIDE. THE CARBON BRUSHES MUST BE REMOVED BEFORE THE MAIN HOUSING ASSEMBLY COVER (f1) IS REMOVED^ LIFT END BRUSH (I) IN ORDER TO PREVENT DAMAGE TO THE CARBON BRUSHES AND TENSION SPRINGS, AND SLIP THE TWO CARBON BRUSHES (H) OFF THE ROTOR CONTACT PIN, (BE EXTREMELY CAREFUL OF THE
ROTOR CONTACT PIN DURING DISASSEMBLY SO YOU DO NOT BEND OR BREAK THE PIN).
(6)
14
SHOULD IT BE NECESSARY TO REMOVE THE CARBON BRUSH AUDIO PICK-UP ASSEMBLY (J). DESOLDER THE AUDIO WIRE FROM THE BRUSH ASSEMBLY AND RFMOVE THE TWO (2) SCREWS (K) TO REMOVE THE END BRUSH (I) REMOVE SCREW (L) AND SEPARATE FROM THE BRUSH ASSEMBLY,
.
(7)
REMOVE THE FOUR C4) SCREWS (n) AND SLIP THE HOUSING COVER (M) OFF THE MAIN ASSEMBLY, MARK THE HOUSING COVER (M) AND THE MAIN ASSEMBLY CHASSIS (U) TO INDICATE THE STARTNOTE: ING POINT OF THE SCANNER CABLE. ALSO MARK THE LOCATION OF THE CABLE CLIP (0),
(8)
STATIONARY PLATES (P) AND ROTOR (Q) ARE MOUNTED ON THE MAIN ASSEMBLY CHASSIS (U) REMOVE TWO (2) OF THE STATIONARY PLATES (P), BY REMOVING SCREWS (R) WHEN REMOVING THE STATIONARY PLATES FROM THE ASSEMBLY YOU WILL NOTICE THAT THERE ARE INSULATOR (S) AND (T) ON BOTH SIDES OF THE MAIN ASSEMBLY CHASSIS, INSULATING THE STATIONARY PLATES FROM THE ASSEMBLY (U) THEN REMOVE THE ROTOR ASSEMBLY (Q) BY LOOSENING THE TWO (2) BRISTOL TYPE SET SCREWS (V). TO AVOID DAMAGING THE ROTOR CONTACT PIN DURING DISASSEMBLY.
.
,
(9)
REMOVE THE REMAINING (14) STATIONARY PLATES AND INSULATORS.

CLEAN THE STATIONARY PLATES, ROTOR PLATES AND OTHER METAL PARTS USING A FREON SPRAY OR OTHER CLEANING SOLVENTS THAT DO NOT LEAVE ANY RESIDUE AFTER DRYING. AN ABSORBENT CLOTH OR SWAB CAN BE USED IN CONJUNCTION WITH THE CLEANERSPRAY METAL COATED PARTS WITH KRYLON CORONA DOPE (CLEAR), TO GET ON OIL THREADS OR ROTOR PICK-UP PIN,
IN
(10)
Cll)
CAUTION;
DO NOT ALLOW SPRAY
(12)
MOST SCANNER REPAIR YOU NEED NOT GO FURTHER IN DISASSEMBLY THAN STEP NUMBER ELEVEN (U) BUT SHOULD CONDITIONS WARRANT FURTHER DISASSEMBLY CONTINUE WITH NUMBER (13). OTHERWISE INSTALL NEW INSULATORS AND REASSEMBLE THE SCANNER. REMOVING THE GEAR HOUSING ASSEMBLY (W) THERE ARE FOUR (4) SCREWS (X) HOLDING THE ASSEMBLY ON TO THE MAIN ASSEMBLY CHASSIS (U). UPON REMOVING THE GEAR HOUSING ASSEMBLY YOU WILL NOTICE THE BAKELITE GEAR AND SHAFT ASSEMBLY (Y) THE SPRINGS ON EITHER SIDE OF THE BAKELITE GEAR ALSO INTERMESHES WITH THE METAL GEAR OF THE SYNCHRONOUS MOTOR TO DRIVE THE SCANNER.
IN
.
(13)
(14)
TO REASSEMBLE THF SCANNER REVERSE THIS PROCEDURE,
HOOO-006059-PL
9/83
PRiNTEDNU.S.A.
OMMUNIC*tlONS

Hammond Organ Service Manual Models M

Uploaded by

Copyright:

Available Formats

Hammond Organ Service Manual Models M

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Hammond Organ Service Manual Models M

Uploaded by

Copyright:

Available Formats

What are some of the main components of an organ?

What are some of the main components of an organ?

What are some common issues that may occur with an organ?

What are some common issues that may occur with an organ?

n

ORGAN SERVICE COMPANY

LaGRANGE ILLINOIS 60525 PHONE 708-352-8011

To protect the user,

cord directiy Into a line voltage

CERAMIC RF BYPASS CAP

CONNECTEQ TO WQWN EARTK ORQUHO

PAGE ONE KEY DOES NOT PLAY

INSTALLATION AND MAINTENANCE

ONE NOTE IS WEAX

CONSTRUCTION AND OPERATION OF COMPONENTS

PROCEDURE FOR REMOVING PARTS

LOWER MANUAL KEY

DRAWBAR CONTACT SPRING DRAWBAR OR DRAWBAR KNOB

CONTROL PANEL ACCESS

REVERBERATION-VOLUME SOFT TABS

MANUAL SECTION OF AMPLIFIER

VIBRATO LINE BOX

INTERMEDIATE SECTION OF AMPLIFIER

PRESET PERCUSSION UNIT

PERCUSSION SECTION OF AMPLIFIER

HARMONIC BUSBAR SWITCHING

TUBE SOCKET VOLTAGES

SPECIAL POV,^R SOURCES

CXMBAL-BRUSH AMPLIFIER AND NOISE GATE

PRACTICAL SERVICE SUGGESTIONS

IiKTALLr\TION AND MAINTENANCE

LIST OF FIGURES AND ILLUSTRATIONS

Front View of Console - Model M Front View of Console - Model M-2

Front View of Console - Model M-3

Front View of Console - Model M-lOO

Block Diagram - Model M

Block Diagram - Model M-2

Block Diagram - Mcdel M-3 Block Diagram - Model M-lOO

Typical Tone Generator

Generator Cover - Model M-3

90485 and above

Generator Cover - Model M-lOO

20. 21. 22. 23.

Fundamental Vibrato System - M

Vibrato System - Model M - 13509 and below Vibrato System

Model M - 13509 and above

Fundamental Vibrato System

LIST OF FIGURES AND ILLUSTRATIONS CONTINUED

26. 27. 28. 29.

Fundamental Vibrato System - M-lOO

Vibrato Line Box - M-lOO Vibrato Scanner Vibrato System M-2

Serial 19000 to 22253

Vibrato System M-2 - Serial 25254 and above

Manual Hold Down Screws

Pictorial - Model M Amplifier

Pictorial - Model M Amp.

- Serial 8411 and above

Wiring Diagram Model M

Wiring Diagram Model M-2

Serial 19000 and above