High Density Polyethylene General Purpose Blow Molding

Recommended Applications:
Product Description:
HDPE 012DB54 is General purpose blow moulding grade
HDPE 012DB54 is a high density bimodal resin grade
recommended for:
produced by Lyondell Basell‘s Hostalen slurry process
 Containers / bottles upto 5 Litre capacities for
with following features:
packaging of Lube oil, Edible oil, FMCG products.
 Good Processability,
 General purpose containers for foodstuffs.

Product Technical Datasheet

Good balance of stiffness & impact properties

 Containers for packing of Chemicals, Detergents,
 Moderate ESCR to suit packaging of Chemicals
Pesticides etc.

Typical Properties:

Tested Properties Test Method UOM Values*

Resin Properties
Melt Flow Index (190°C & 5 Kg) ASTM D 1238 gm/10 min 1.3
3
Density @ 23°C ASTM D 1505 gm/cm 0.9520
Mechanical Properties**
Tensile Strength @ Yield (Type-IV) ASTM D 638 MPa 30
Elongation @ Yield (Type-IV) ASTM D 638 % 10
Elongation @ Break (Type-IV) ASTM D 638 % 1000
Flexural Modulus ASTM D 790 MPa 1200
Notched Izod Impact Strength @ 23°C ASTM D 256 A J/m 150
Hardness ASTM D2240 Shore D 61
Thermal Properties
Vicat Softening Point ASTM D 1525 °C 124
Heat Deflection Temperature ( 0.455 MPa) ASTM D 648 °C 75
Environmental Properties
ESCR ( 10% Igepal), F50 ASTM D 1693 B Hrs >200
* Typical values not to be construed as specification limits. Values may change without any prior notice.
** Mechanical properties were determined on compression moulded specimens.

o
Recommended Processing Temperature: 160 – 200 C
Packaging Information:
This material is packed and available in raffia bags with net content of 25.0 Kg only. The raffia bags used conforms to the minimum strength requirements of BIS,
however, customer shall take due care while handling the bag. Prolonged exposure of these bags to sunlight may deteriorate the bag’s performance and cause
spillage and wastage. IOCL does not warranty loss of material due to poor material handling practices.

Regulatory Information: Storage & Handling:

Prevent HDPE Material from direct exposure to sunlight & heat to avoid quality
HDPE 012DB54 meets "Specification for Polyethylene for safe use deterioration. The storage location should be dry, dust free and the Storage
in contact with Foodstuff, Pharmaceutical & Drinking water” as per temperature should not exceed 50 oC. Non - compliance to these precautionary
IS:10146-1982. It also conforms to the positive list of constituents measures can lead to degradation of the product causing Color changes, Odor &
as prescribed in IS:10141-1982. The grade and Additives inadequate product performance. It is advised to process HDPE material within 06
incorporated meet with FDA:CFR Title21,177.1520, Olefin months after delivery.
Polymers.

Disclaimer: IOCL assumes no liability whatsoever in respect of application, processing or any use made of the aforementioned information or products, or any consequence thereof. No liability whatsoever shall attached to any
of the IOCL companies for any infringement of the rights owned or controlled by a third party in intellectual, industrial or other property by reason of application, processing or use of the afore-mentioned information or products
by the user.

Registered Office Address  Contact Address  Contact Details 

Indian Oil Corporation Limited, Indian Oil Corporation Limited, Tel : +91-180-2526705, 2527705
G-9, Aliyavar Jung Marg, Product Application and Development Center (PADC), Fax : +91-180-2528689
Bandra (East), Mumbai – 400051 Near Panipat Naphtha Cracker Complex, Web : https://propel.indianoil.in
Maharashtra, India. Village – Baljattan, Panipat – 132140, Haryana, India

02-12/17