MasterBrace® LAM

High Strength and High Modulus Unidirectional Pultruded Carbon Fiber Laminates for
strengthening reinforced concrete structures

DESCRIPTION leakage it must be drained or properly sealed. In case

MasterBrace LAM is high strength or high modulus of low strength concrete (<1.5N/mm²), the loose con-
unidirectional pultruded carbon fiber laminates in Mas- crete must be broken out and the surfaces should be
terBrace FRP System. reprofilled with structural repair mortars from the Mas-
terEmaco S range. Before the MasterBrace SAT/
TYPICAL APPLICATIONS MasterBrace Primer application let repair mortars
cure for at least 7 days. FRP sheets should be free of
• Increasing flexural strength of concrete beams
oil stains and dust. Contact Master Builders Solutions
• Increasing flexural strength of concrete slabs under
Technical Services Department for advice on prepara-
heavy machine loads
tion.
• Increasing rigidity of beams and slabs against bend-
ing deformations Before the adhesive application let the repair mortars
• Increasing flexural strength of concrete slabs dam- cure at least 7 days at 20°C. FRP sheets should be
aged with ventilating channel openings, stairs and el- free of oil stains and dust. Contact Master Builders
evator holes etc Solutions Technical Services Department for advice
• Increasing flexural strength of concrete beams and on preparation.
slabs under increased service loads (change of us-
age etc.)
PLACING / APPLICATION
• Decreasing disturbing effect of vibrations on concrete MasterBrace ADH 1438 / MasterBrace ADH 4000 /
slabs caused by mechanical equipment MasterBrace ADH 2200 should be applied to the
prepared surfaces and to FRP laminates by using a
ADVANTAGES steel spatula or steel trowel. Application thickness
• Light and easy to carry should be between 1.0-2.0 mm. In the following 10
• Easy to cut and re-shape minutes (at 25°C) FRP laminates should be placed on
• Easy to design (Unidirectional laminates and similar to the substrate and pushed onto the laminates with a
elasticity modulus with steel) stiff roller (polyamide, steel etc.) for preventing possi-
• Does not increase the dead load of the structure ble air gaps between the laminate and substrate. For
• Decreases the bending deformations in the slabs further details please refer to MasterBrace ADH 1438
and beams / MasterBrace ADH 4000 / MasterBrace ADH 2200.
• Flexible application method allows building opera-
tion to continue CLEANING
After the application all tools should be cleaned with a
PACKAGING proper detergent or solvent such as thinner.
Length - 100 m rolls.
- 200 m rolls (only for 20mm x 1.2 / 1.4) WATCHPOINTS
MasterBrace FRP applications should be done by
APPLICATION GUIDELINES approved experts. Work clothes, protective gloves,
glasses and masks must be used during the applica-
tion. Do not touch the fibers without gloves. Consult to
SURFACE PREPARATION the Master Builders Solutions Technical Services De-
The mineral based substrates (concrete & brick) must partment for advice on application method.
be sound, clean and dry. The concrete should be free
of frost, curing membranes, waterproofing treatments,
oil stains, laitance, friable material and dust. If there is
a water

Page 1 of 2
MasterBrace® LAM
High Strength and High Modulus Unidirectional Pultruded Carbon Fiber Laminates for
strengthening reinforced concrete structures

TYPICAL PROPERTIES*
MasterBrace LAM MasterBrace LAM MasterBrace MasterBrace LAM
50/1.2 CFS 50/1.4 CFH LAM 100/1.2 100/1.4 CFH
CFS
Elasticity Modulus 165,000 210,000 165,000 210,000
(N/mm²)
Tensile Strength 3,000 2,800 3,000 2,800
(N/mm²)
Elongation at Break (%) 1.8 1.4 1.8 1.4
Thickness S (mm) 1.2 1.4 1.2 1.4
Width (mm) 50 50 100 100
Cross Section Area 60 70 120 140
(mm²)
*Other dimensions available, please contact Master Builders Solutions for further information

STORAGE • Under no circumstances drink, eat or smoke

Store in original container in cool (+5°C to 30°C) during use.
and dry indoor conditions. • Comply with safety regulations on the use of
products that are inflammable or contain sol-
HEALTH AND SAFETY vents.
• Always wear gloves, goggles and suitable work
For applications with surfaces, climatic conditions or
clothes during mixing in order to avoid contact
use other than those indicated in the product sheet
with the skin.
contact our Technical department.
• In the event of accidental contact, thoroughly
wash the affected parts with water and soap or
an appropriate detergent. QUALITY AND CARE
All products originating from Master Builders Solu-
• Do not use solvents or thinners.
tions Dubai, UAE facility are manufactured under a
• Do not inhale the vapours and sprays; a contin- management system independently certified to
ual change of air should be ensured for applica- conform to the requirements of the quality, envi-
tion in a closed environment. ronmental and occupational health & safety stand-
ards ISO 9001, ISO 14001 and ISO 45001.

® = registered trademark of a MBCC Group member in many countries of the world MID#MasterBrace® LAM - 07.2021
The technical information and application advice given in this Master Builders Solutions publication are based on
STATEMENT OF the present state of our best scientific and practical knowledge. As the information herein is of a general nature,
RESPONSIBILITY no assumption can be made as to a product's suitability for a particular use or application and no warranty as to its
accuracy, reliability or completeness either expressed or implied is given other than those required by law. The
user is responsible for checking the suitability of products for their intended use.

Field service where provided does not constitute supervisory responsibility. Suggestions made by Master Builders
NOTE Solutions either orally or in writing may be followed, modified or rejected by the owner, engineer or contractor
since they, and not Master Builders Solutions, are responsible for carrying out procedures appropriate to a specific
application.

PT Master Builders Solutions Indonesia

Jl. Jababeka V Blok I No 1, Kawasan Industrial Estate
Jababeka 1, Pasirgombong, West Cikarang,
Bekasi, West Java 17530
www.master-builders-solutions.com/en-id

Page 2 of 2