UART Protocol
UART Protocol
If we remember the old computer parts like printer, mouse, the keyboard is associated
with the help of connectors. The communication process between the computer and these
parts could be done using the UART. Universal Serial Bus (USB) has changed all kinds of
communication principles on computers. But, UART is still used in the above-declared
applications. Approximately all all types of microntrollers architectures have built-in
UART hardware due to serial communication and use only two cables for
communication. This article discusses what UART, How UART Works, the difference
between serial and parallel communication, UART block diagram, UART
communication, UART interfacing, Applications, Advantages, and Disadvantages.
What is UART?
The UART full form is “Universal Asynchronous Receiver/Transmitter”, and it is an
inbuilt IC within a microcontroller but not like a communication protocol (I2C & SPI).
The main function of UART is to serial data communication. In UART, the
communication between two devices can be done in two ways namely serial data
communication and parallel data communication.
Page 1 of 6
EmbeddedXpress
UART
Serial and Parallel Communication
In serial data communication, the data can be transferred through a single cable or line
in a bit- by- bit form and it requires just two cables. Serial data communication is not
expensive when we compared with parallel communication. It requires very less circuitry
as well as wires. Thus, this communication is very useful in compound circuits compared
with parallel communication.
In parallel data communication, the data can be transferred through multiple cables at
once. Parallel data communication is expensive as well as very fast, as its requires
additional hardware and cables. The best examples for this communication are old
printers, PCI, RAM, etc.
The hold register in the transmitter comprises the data-byte to be transmitted. The shift
registers in transmitter and receiver move the bits to the right or left till a byte of data is
transmitted or received. A read (or) write control logic is used for telling when to read or
write.
Page 2 of 6
EmbeddedXpress
The baud-rate-generator among the transmitter and the receiver generates the speed that
ranges from 110 bps to 230400 bps. Typically, the baud rates of microcontrollers are 9600
to 115200.
Page 3 of 6
EmbeddedXpress
UART Communication
In this communication, there are two types of UARTs available namely transmitting
UART and receiving UART, and the communication between these two can be done
directly by each other. For this, simply two cables are required to communicate between
two UARTs. The flow of data will be from both the transmitting (Tx) & receiving (Rx)
pins of the UARTs. In UART, the data transmission from Tx UART to Rx UART can be
done asynchronously (there is no CLK signal for synchronizing the o/p bits).
The data transmission of a UART can be done by using a data bus in the form of parallel
by other devices like a microcontroller, memory, CPU, etc. After receiving the parallel
data from the bus, it forms a data packet by adding three bits like start, stop and parity.
It reads the data packet bit by bit and converts the received data into the parallel form to
eliminate the three bits of the data packet. In conclusion, the data packet received by the
UART transfers in parallel toward the data bus at the receiving end.
UART Communication
Start Bit
Start-bit is also known as a synchronization bit that is placed before the actual data.
Generally, an inactive data transmission line is controlled at a high-voltage level. In order
to begin the data transmission, the UART transmission drags the data-line from a high
voltage level (1) to a low voltage level (0). The obtaining UART notices this transform
from the high level to low level over the data line as well as starts understanding the real
data. Generally, there is just a single start bit.
Stop Bit
The Stop Bit is placed at the ending of the data packet. Usually, this bit is 2-bits lengthy
but frequently on bit only utilized. In order to stop the broadcast, the UART keeps the
data-line on high voltage.
Page 4 of 6
EmbeddedXpress
Parity Bit
Parity bit lets the receiver to ensure whether the collected data is right or not. It is a low-
level fault checking system & parity bit is available in two ranges such as Even Parity as
well as Odd Parity. Actually, this bit is not widely used so it is not compulsory.
UART Interfacing
The following figure shows UART interfacing with a microcontroller. The UART
communication can be done using three signals like TXD, RXD, and GND.
By using this, we can exhibit a text in personal computer from 8051 microcontroller board
as well as the UART module. In 8051 board, there are two serial interfaces such as UART0
and UART1. Here, UART0 interfacing is used. The Tx pin transmits the information to
PC & Rx pin receives the information from PC. Baud rate can be used to denote the speeds
of both the microcontroller and PC. The data transmission and reception can be done
properly when the baud rates of both microcontroller & PC are similar.
UART
Interfacing
Applications of UART
UART is normally used in microcontrollers for exact requirements, and these are also
available in various communication devices like wireless communication, GPS
units, Bluetooth, and many other applications.
The communication standards like RS422 & TIA are used in UART except for RS232.
Usually, a UART is a separate IC used in UART serial communications.
Page 5 of 6
EmbeddedXpress
Advantages and Disadvantages of UART
The pros and cons of UART include the following
Page 6 of 6
EmbeddedXpress