ORDER NO.

KMS0104563C1
F5

DIGITAL PROPRIETARY TELEPHONE

KX-T7453 / KX-T7453B
White Version
Black Version
(for U.S.A.)

SPECIFICATIONS
1. CAUTION
Note:
When you note the serial number, write down all of the 11 digitals.
The serial number may be found on the label affixed to the bottom of the unit.

2. FOR SERVICE TECHNICIANS

1. Note the following items when exchanging the LEDs (Ref. No. D100-
130, D201, D202) of Dial P.C. Board.
1) Do not reuse a LED which is removed from the P.C. Board.
2) Use a soldering iron (less than 15 W) for exchanging LED.
3) Do not heat the LED for more than 2 seconds.
4) Do not move the LED after soldering.
2. This unit employs the switch which is influenced by the light for the
hook switch.
When you open the cabinet to repair the unit in the bright light, the
hook switch might work improperly.
Therefore, take care not to shine the hook switch directly, or use the
jig as shown below.

3. LOCATION OF CONTROLS

2
4. DISASSEMBLY INSTRUCTIONS
4.1. HOW TO REMOVE THE LOWER CABINET
(Procedure 1)

(1) Remove the 4 screws A.

(2) Remove the lower cabinet.

3
4.2. HOW TO REMOVE THE HOOK BUTTON
(Procedure 1 2)

(1) Remove the hook button.

4.3. HOW TO REMOVE THE SWITCH AND MAIN BOARDS

(Procedure 1 2 3)

4
(1) Remove the screws A.
(2) Pull out the switch board connector.
(3) Remove the switch board.
(4) Pull out the flat cable. (See Fig. 1)
(5) Remove the 2 screws B.
(6) Pull out the speaker and microphone connectors.
(7) Remove the main board.

4.4. HOW TO REMOVE THE LCD BOARD

(Procedure 1 4)

5
(1) Pull out the flat cable. (See Fig. 1)
(2) Remove the LCD block. (See Fig. 2)
(3) Remove the 2 screws A.
(4) Remove the lower cabinet.
(5) Remove the LCD board.

6
5. IC DATA
5.1. IC1

7
Name Pin Dir. Pull Up Type Io Act. Block MHz Descriptions
DB3 2 bidir --- TTL 8.0mA high PT5B03 2.0 Data Bus [3]
DB2 3 bidir --- TTL 8.0mA high PT5B03 2.0 Data Bus [2]
DB1 4 bidir --- TTL 8.0mA high PT5B03 2.0 Data Bus [1]
DB0 5 bidir --- TTL 8.0mA high PT5B03 2.0 Data Bus [0]
ADR1 6 input 12-38k TTL --- high PT5D01U 2.0 Address Bus [1]
ADR0 7 input 12-38k TTL --- high PT5D01U 2.0 Address Bus [0]
CSN 8 input --- TTL --- low PT5D01 1.0 Chip Select
REN 10 input 12-38k TTL --- low PT5D01U 2.0 Read Enable Command
WEN 9 input 12-38k TTL --- low PT5D01U 2.0 Write Enable Command
RST 63 input --- CMOS --- high PC5D21 0.01 Asynchronous Reset Inp
schmidt
INT0N 11 output --- CMOS 2.0mA low PC5O01 0.01 Interrupt Request
INT1N 12 output --- CMOS 2.0mA low PC5O01 0.01 Interrupt Request
DR0 38 input --- CMOS --- low PC5D01 0.6 Dpits Receive Data [1]
DR1 39 input --- CMOS --- low PC5D01 0.6 Dpits Receive Data [0]
DX0 40 output --- CMOS 4.0mA low PC5O02 0.6 Dpits Transmit Data [1]
DX1 41 output --- CMOS 4.0mA low PC5O02 0.6 Dpits Transmit Data [0]
CK512K 37 output --- CMOS 2.0mA high PC5O01 0.6 Dpits Bit Rate Clock
SR0 19 input 12-38k TTL --- high PT5D01U 0.1 Serial Receive Data
Stream [0]
SR1 20 input 12-38k TTL --- high PT5D01U 0.1 Serial Receive Data
Stream [1]
SX 21 output --- CMOS 4.0mA high PC5O02 0.1 Serial Transmit Data
Stream
CK2M 18 output --- CMOS 4.0mA high PC5O02 2.1 Serial Stream Clock
EP0 13 output --- CMOS 2.0mA high PC5O01 0.01 External Channel Pulse [
EP1 14 output --- CMOS 2.0mA high PC5O01 0.01 External Channel Pulse [
EP2 15 output --- CMOS 2.0mA high PC5O01 0.01 External Channel Pulse [
EP3 16 output --- CMOS 2.0mA high PC5O01 0.01 External Channel Pulse [
PI 61 input --- CMOS --- high PC5D21 0.01 Rotary Encoder Input
schmidt [Pos]
NI 62 input --- CMOS --- high PC5D21 0.01 Rotary Encoder Input
schmidt [Neg]
CLM0 43 output --- CMOS 4.0mA high PC5O02 0.01 LED Column Drive [0]
CLM1 44 output --- CMOS 4.0mA high PC5O02 0.01 LED Column Drive [1]
CLM2 45 output --- CMOS 4.0mA high PC5O02 0.01 LED Column Drive [2]
CLM3 46 output --- CMOS 4.0mA high PC5O02 0.01 LED Column Drive [3]
CLM4 47 output --- CMOS 4.0mA high PC5O02 0.01 LED Column Drive [4]
CLM5 48 output --- CMOS 4.0mA high PC5O02 0.01 LED Column Drive [5]
NROW0 50 output --- CMOS 4.0mA low PC5O02 0.01 LED Row Drive [0]
NROW1 51 output --- CMOS 4.0mA low PC5O02 0.01 LED Row Drive [1]
NROW2 52 output --- CMOS 4.0mA low PC5O02 0.01 LED Row Drive [2]
NROW3 53 output --- CMOS 4.0mA low PC5O02 0.01 LED Row Drive [3]
NROW4 54 output --- CMOS 4.0mA low PC5O02 0.01 LED Row Drive [4]
NROW5 55 output --- CMOS 4.0mA low PC5O02 0.01 LED Row Drive [5]
NROW6 56 output --- CMOS 4.0mA low PC5O02 0.01 LED Row Drive [6]

8
NROW7 57 output --- CMOS 4.0mA low PC5O02 0.01 LED Row Drive [7]
NROW8 58 output --- CMOS 4.0mA low PC5O02 0.01 LED Row Drive [8]
NROW9 59 output --- CMOS 4.0mA low PC5O02 0.01 LED Row Drive [9]
IP0 27 input 12-38k CMOS --- high PC5D01U 0.01 Input Port [0]
IP1 28 input 12-38k CMOS --- high PC5D01U 0.01 Input Port [1]
IP2 29 input 12-38k CMOS --- high PC5D01U 0.01 Input Port [2]
IP3 30 input 12-38k CMOS --- high PC5D01U 0.01 Input Port [3]
OP0 23 output CMOS 4.0mA high PC5O02 0.01 Output Port [0]
OP1 24 output CMOS 4.0mA high PC5O02 0.01 Output Port [1]
OP2 25 output CMOS 4.0mA high PC5O02 0.01 Output Port [2]
OP3 26 output CMOS 4.0mA high PC5O02 0.01 Output Port [3]
CK2K 22 output CMOS 4.0mA high PC5O02 0.20 2kHz Clock Output (duty
25%)
CK16M 36 output --- CMOS 2.0mA high PC5O01 16.4 Master Clock Out
OSI 33 input --- Analog --- --- PC5X02 16.4 X'tal In (XIN)
OSO 34 output --- Analog --- --- PC5X02 16.4 X'tal Out (XOUT)
N.C. 32 not used
N.C. 42 not used
N.C. 60 not used
VDD1 1 vdd Vdd (5V)
VDD2 31 vdd Vdd (5V)
VDD3 49 vdd Vdd (5V)
VSS1 17 vss Vss (GND)
VSS2 35 vss Vss (GND)
VSS3 64 vss Vss (GND)

5.2. IC2

9
10
 Name NO. I/O Classification Function
APMP 1 Analog Analog Non-inverting input terminal of microphone amplifier M1.
input Connect to the microphone.
VREFDA 2 --- Power. Reference voltage teminal of DAC.
supply, etc. Connect the capacitor of 40 F between this terminal and pi
(AG2).
AG1 3 Ground terminal of the analog circuit.
HO+ 4 Analog Analog Output terminal for the handset receiver.
HO- 5 output HO+ terminal and HO- terminal are biased to Vdd/2 voltage.
HO- terminal is the inverse porality output terminal for pin 4 (H
+).
Connect the capacitor in series between the handset and thes
terminals to cut the DC.
Use the nonpolar type capacitor.
A5V1 6 --- Power 5V power supply terminal of analog circuit.
A5V2 7 supply, etc.
SPO 8 Analog Analog Output treminal for the speaker amplifier.
output Connect to the external speaker amplifier input terminal.
SPO terminal is biased to Vdd/2 voltage.
Connect the capacitor of 0.1 F in series between the extern
speaker amplifier input terminal and this terminal.
AG2 9 --- Powers Ground terminal of the analog circuit.
supply, etc.
P/-S 10 CMOS Micro- Mode selection terminal of microcomputer interface.
input computer Inputting “0“ selects the serial mode, and “1“ selects the
interface parallel mode.
-RESET 11 System reset terminal.
The system is reset when “0“ is pressed.
DG1 12 --- Powers Ground terminal of the digital circuit.
supply, etc.
OP0 13 3 states Output port Outputs BIT0 signal of OPORT1 resistor.
OP1 14 output Outputs BIT1 signal of OPORT1 resistor.
D5V1 15 --- Powers 5V power supply terminal of digital circuit.
supply, etc.
OP2 16 3 states Outputs BIT2 signal of OPORT1 resistor.
OP3 17 output Outputs BIT3 signal of OPORT1 resistor.
OP4 18 Output Outputs BIT4 signal of OPORT1 resistor.
OP5 19 Outputs BIT5 signal of OPORT1 resistor.
OP6 20 Outputs BIT6 signal of OPORT1 resistor.
OP7 21 Outputs BIT7 signal of OPORT1 resistor.

11
RXD 22 TTL Input terminal for PCM data.
input
TXD 23 output Output terminal for PCM data
-FSYNC 24 TTL Input terminal of Sync. signal for PCM interface. The frequenc
input PCM of input sync.
interface signal is 8 kHz.
BCLK 25 Input terminal of shift clock pulse for PCM deta. Input pulse
frequency range is 64 kHz~2.048 kHz.
PCM data (TXD termianl signal) is output st the positive edge.
PCM data (RXD terminal signal) is sampled at the negative ed
The sameling is performed inside LSI.
MCLK 26 Output Clock Clock pulse output terminal. Output pulse frequency is
6.144MHz.
System reset (inputting “0” to -RESET terminal) doesn’t stop
this output.
CLKO 27 Clock pulse output terminal which has selective frequencies.
The following 4 frequencies can be selected by resistor settin
12.228, 4.096, 2.048, 1.536 (MHz).
System reset (inputting “0” to -RESET terminal) selects the
frequency of 1.536MHz and doesn’t stop this output.
DG2 28 --- Power Ground terminal of digital circuit.
supply, etc.
OSCI 29 --- Clock Input terminal of oscillation circuit.
Connect the oscillator and resistor berween this terminal and
pin 30 (OSCO), moreover, connect the capacitor between this
terminal and digital ground to make the oscillation circuit.
OSCO 30 --- Output terminal of oscillation circuit.
Connect the oscillator and resistor berween this terminal and
pin 29 (OSCI), moreover, connect the capacitor between this
terminal and digital ground to make the oscillation circuit.
D5V2 31 --- Power 5V power supply terminal of digital circuit.
supply, etc.
-INT 44 Output Micro- Outputs 8 kHz clock pulse which is synchronized with -FSYNC
computer
interface
TEST 45 CMOS Power Test terminal
input supply, etc. Connect to the digital ground.
A5V3 46 --- 5V power supply terminal of analog circuit.
HI 47 Analog Analog Input terminal of TX handset signal.
input Either this signal or the signal supplied to pin 49 (HI) is input
AD converter.
VBB 48 --- Power Reference voltage terminal of AD converter.
supply, etc. Connect the capacitor of 10 F between VBB terminal and p
50 (AG3).
MI 49 Analog Analog Input terminal of TX microphone signal.
input Either this signal or the signal supplied to pin 47 (HI) is input
AD converter.

12
AG3 50 --- Power Ground terminal of analog circuit.
A5V4 51 supply, etc. 5V power terminal of analog circuit.
AP2HO 52 Analog Output terminal of microphone amplofier H2.
output Connect the capacitor of 0.1 F to this terminal to cut the DC
AP2HI 53 Analog Inverting input terminal of microphone amplofier H2.
input Analog Connect the capacitor of 0.1 F to this terminal to cut the DC
AP1HO 54 Analog Output terminal of microphone amplofier H1.
output Connect the capacitor of 0.1 F to this terminal to cut the DC
AP1HN 55 Analog Inverting input terminal of microphone amplofier H1.
input Connect to the handset.
AP1HP 56 Analog Analog Non-inverting input terminal of microphone amplofier H1.
input
VREFM 57 --- Power Reference voltage terminal of microphone amplifier.
supply, etc. Connect the capacitor of 40 F between this terminal and pi
56 (MICG).
AG4 58 Ground terminal of analog circuit.
APMO 59 Analog Output terminal of microphone amplifier.
input Analog Connect the capacitor of 0.1 F to this terminal to cut the DC
APMN 60 Analog Non-inverting input terminal of microphone amplofier M.
input

6. BLOCK DIAGRAM
7. CIRCUIT OPERATIONS
7.1. KEY INPUT CONTROL CIRCUIT
1) Circuit Operation

Sequential input information (negativa logic) from the DSHS proprietary telephone is executed by
dynamic scanning.
The ports RR70 to RR73, RR80 to RR83 of IC6 are brought to low status consecutively.
If a key is pressed, the key-in information input is executed by ports R91 to R93, RB1, RB11, RB21,
RB0, RD1.

13
7.2. LCD CONTROL CIRCUIT
1) Circuit Operation

The LCD data is output from pins 32 to 35, 40 to 47 and 11 of IC6.

LCD contrast adjustment is performed by the circuit composed of Q28, Q29, R109, R108 and R106.
The contrast is determined only by the voltage level between V5 and VEE of IC202 and IC201.
Higher potential makes the contrast high.

14
15
7.3. LED CIRCUIT
1) Circuit Operation

The LED executes dynamic lighting for the status indicators, and control is executed by the output
ports C0 to C5 (column) and R0 to R9 of IC1.
A fixed pulse (T=1.82 msec) is output continuously from the/SCK1 terminal of IC9. This pulse is
counted and the output of IC1 is shifted sequentially from C0 to C5.
R0 to R7 of IC1 also output pulses, and the lighting of the LED is controlled by the timing of the output
ports C0 to C5.

16
7.4. DATA COMMUNICATION CIRCUIT
1) Function

The data communication circuit serves the following functions:

Information exchanger between the DSHS and DSHS proprietary telephone, key input information as
well as data for the LED control, LCD control, etc. This information is continuously exchanged at all

17
times.

2) Circuit Operation

When the DSHS propritary telephone receives an IRQ signal from the DSHS and after sending the key
input information to the DSHS and receivung data for the LED control, etc., the DSHS proprietary
telephone will return to the DSHS an acknowledge signal.

3) Reception

The data from the DSHS is received via the H and L lines along the path shown below.
H, L Line T1 IC11 Pin 5, 10 IC1 Pin 38, 39 IC1 Pin 21 IC2 Pin 22

4) Transmission

The data to the DSHS proprietary telephone is transmitted along the following path.
IC2 Pin 23 IC1 Pin 20 IC1 Pin 40, 41 Q1, Q2 T1 H, L Line

5) IC1 (GATE ARRAY) DPITS Interface

DPITS Layer 1 interface. DR [1:0] is receiving input and DX [1:0] is transmitting output.

18
Layer 1 is the transmission method of Ping-Pong type which is AMI encoded. “SYNC/MAM/C/D/B1/B2/
P” data is received in the first half at 125us/frame. After 1 bit time has passed since receiving P data,
“SYNC/MAM/C/D/B1/B2/P” is transmitted. 1 bit time is 512kHz. 7-bit time idle term comes after
receiving P data.

6) PCM interface (between IC1 and IC2)

PCM interface consists of following 4 terminals.

The first PCM data is output from TXD at the positive edge of -FSYNC. The second data and the
followings are output at the positive edge of BCLK. After all data of 8 bit are output, the last data is
kept until the positive edge of next -FSYNC. The positive edge of BCLK should be within ±100ns from
the positive edge of -FSYNC.
The PCM data input from RXD is sampled at the negative edge of BCLK inside LSI. The sampling of
the first data is performed between the positive edge of -FSYNC and the first negative edge of BCLK.
After completing the sampling of all data of 8 bit, this sampling pauses until the next positive edge of -
FSYNC.

19
7.5. RESET CIRCUIT
1) Circuit Operation

This circuit is used for transmission of a reset pulse to the CPU (IC6) at the following times,
connecting the telephone line jack and circuit operation.
The timing chart is shown below.

20
The reset signal is negledted.

21
7.6. TONE GENERATION CIRCUIT
1) Function

Calling tones, Busy tone, DTMF signal and Key in tone are generated in IC2.

22
7.7. JOG DIAL CIRCUIT
1) Circuit Operation

This unit is equipped with the JOG switch, which makes the settings of the volume, function selection
speed dial, etc. easy and convenient. This JOG switch consists of 2-phase rotary encoder, and the
gate array of IC1 counts the number of the rotation to control. The sampling cycle is 1ms and
provided with the chattering protective circuit whose available pulse width is 1ms or more.

These are the rotary encoder inputs, and sampled 1 kHz (1 msec)/cycle. The built-in chattering
protective circuit neglects the input pulse of 1 msec or less. The high pulse of 2 msec or more is
available. The availability of the pulse with the width of 1~2 msec is not ensured.
The changed number of these 2-phase inputs is counted cumulatively. The maximum counting value
is 255.

23
7.8. HOOK SWITCH CIRCUIT
1) Circuit Operation

The hook switch of this unit employs the photo switch consisting of LED and photo transistor. The
2kHz pulse from the gate array of IC2 causes the LED to emit the light. The light is interrupted at ON-
HOOK and passes through at OFF-HOOK by the hooking bar,so that the hooking is performed
controlling the light of the photo transistor. The detection signal is determined by the microcomputer
of IC6.

7.9. HANDSET CIRCUIT

1) Transmission signal path

The analog input signal from the handset microphone is input to the communication LSI through the
IC2 built-in analog amplifier. In this LSI the network control based on A/D conversion and the handset
software and the gain control based on the down load data from the PBX are performed. The voice
data is sent to IC1 by the serial transmission. The voice data is transmitted between PBX and DPITS
with the protocol originated by KME.

2) Reception signal path

24
The voice serial data transmitted from PBX is sent to IC1 or IC2 by the serial data. The network
control, gain control , A/D conversion is performed in IC2, then the data is output from the handset
speaker. Q31 of the handset speaker performs the mute operation by controlling IC6.

3) Circuit diagram for transmission/reception signal path

Refer to page SCHEMATIC DIAGRAM ().

7.10. SP-PHONE CIRCUIT

1) Transmission signal path

The analog input signal from SP-phone microphone is input to the communication LSI through the IC2
built-in analog amplifier. In this LSI the network control based on A/D conversion and the handset
software and the gain control based on the down load data from the PBX are performed. The voice
data is sent to IC1 by the serial transmission. The voice data is transmitted between PBX and DPITS
with the protocol originated by KME. IC3 is the SP-phone amplifier, which turns ON/OFF using the
port of IC2. The analog switch of IC12 interrupts the input signal.

2) Reception siganl path

The voice serial data transmitted from PBX is sent to IC2 by the serial transmission. Then the signal is
output from the handset speakerphone after performing the network control, gain control, and A/D
conversion in IC2. The SP-phone microphone has the mute function, which interrupts the input signal
with the analog switch and controls the port of IC2 with Q26.

3) Circuit diagram for transmission/reception signal path

Refer to page SCHEMATIC DIAGRAM ().

8. TROUBLESHOOTING GUIDE
8.1. NO OPERATION.

25
8.2. THE LCD DOES NOT OPERATE.

26
8.3. THE ELECTRONIC VOLUME OF THE SPEAKER-PHONE DOES NOT
WORK.

8.4. THE ELECTRONIC VOLUME OF THE HANDSET DOES NOT WORK.

27
8.5. SPEAKER-PHONE TROUBLE.

8.6. TONE DIAL TROUBLE.

8.7. HANDSET TROUBLE.

28
9. TERMINAL GUIDE OF ICS, TRANSISTORS AND
DIODES

29
10. HOW TO REPLACE THE FLAT PACKAGE IC
If you do not have the special tools (for example: SPOT HEATER) to remove the SPOT HEATER’S Flat
IC, If you have solder (large amount) a soldering iron and a cutter knife, you can easily remove IC’s
even though large than 100 pin.

10.1. PREPARATION
- SOLDER
Sparkle Solder 115A-1, 115B-1 or Almit Solder KR-19, KR-19RMA
- Soldering iron
Recommended power consumption is between 30 W to 40 W.
Temperature of Copper Rod 662 ± 50°F (350 ± 10°C)
(An expert may handle a 60~80 W iron, but beginner might damage foil
by overheating.)
- Flux
HI115 Specific gravity 0.863
(Original flux should be replaced daily.)
10.2. FLAT PACKAGE IC REMOVE PROCEDURE
1. When all of the IC lead can not been seen at the standard degree, fill
with large quantities of solder.

30
Note:
If you do not fill with solder and directly cut the IC lead with the cutter, stress may build up directly in
the P.C.board’s pattern. If you do not fill with large quantities of solder as in step 1 the P.C.board
pattern may be removed.

2. Using a cutter, cut the lead at the source. (Cut the contents with the
cutter lightly 5 or 6 times.)

3. Remove when the solder melts. (Remove the lead at the same time.)

After removing the Flat IC and when attaching the new IC, remove any of the excess solder on the
land using the soldering wire, etc. If the excess solder is not removed from the land, the IC will slip
and not be attached properly.

10.3. FLAT PACKAGE IC INSTALLATION PROCEDURE

31
1. Temporary fix FLAT PACKAGE IC by soldering on two marked pins.

*Check the accuracy of the IC setting with the corresponding soldering foil.

2. Apply flux for all pins of FLAT PACKAGE IC.

3. Solder using the specified solder, in the direction of the arrow, by

sliding the soldering iron.

10.4. BRIDGE MODIFICATION PROCEDURE

1. Lightly re-solder the bridged portion.
2. Remove the remaining solder along pins using a soldering iron as
shown in the figure below.

11. WAVEFORM

12. CABINET AND ELECTRICAL PARTS LOCATION

32
13. ACCESSORIES AND PACKING MATERIALS

33
14. REPLACEMENT PARTS LIST
Note:

1. The marking (RTL) indicates that the Retention Time is limited for this
item.

34
 After the discontinuation of this assembly in production, the item will
continue to be available for a specific period of time. The retention
period of availability depends on the type of assembly and the laws
governing parts and product retention. After the end of this period, the
assembly will no longer be available.
2. The S mark indicates service standard parts and may differ from
production.
3. RESISTORS & CAPACITORS
Unless otherwise specified;
All resistors are in ohms ( ) K=1000 , M=1000k
All capacitors are in MICRO FARADS ( F) P= F
*Type & Wattage of Resistor

14.1. CABINET AND ELECTRICAL PARTS

35
 Ref. No. Part No. Part Name & Description Remarks
1 PSKM1052T1 CABINET, UPPER (WHITE VERSION)
1 PSKM1052T3 CABINET, UPPER (BLACK VERSION)
2 PSGD1026Z CARD, DIAL (WHITE VERSION)
2 PSGD1033Z CARD, DIAL (BLACK VERSION)
3 PSHR1134Z COVER, TEL CARD
4 PQKE82X1 HANGER (WHITE VERSION)
4 PQKE82X2 HANGER (BLACK VERSION)
5 PQHR576Z COVER, TEL NO.
6 PQHP532X CARD, TEL NO.
7 PSBC1012Z1 BUTTON, JOG DIAL (WHITE VERSION)
7 PSBC1012Z2 BUTTON, JOG DIAL (BLACK VERSION)
8 PSHR1164Y SPACER, JOG DIAL
9 PSBH1002Y1 BUTTON, HOOK (WHITE VERSION)
9 PSBH1002Y2 BUTTON, HOOK (BLACK VERSION)
10 PSUS1006Z SPRING
11 PQAS65P28Z SPEAKER
12 PSJS02Q35Z CONNECTOR, 2P
13 RJM142Z MICROPHONE S
14 PSHG1122Z RUBBER PARTS, MIC COVER
15 PSBX1041Z3 BUTTON, 15KEY (WHITE VERSION)
15 PSBX1041Z4 BUTTON, 15KEY (BLACK VERSION)
16 PSBX1039Z1 BUTTON, DIAL (WHITE VERSION)
16 PSBX1039Z2 BUTTON, DIAL (BLACK VERSION)
17 PSYX1001Z1 BUTTON, 3KEY (WHITE VERSION)
17 PSYX1001Z2 BUTTON, 3KEY (BLACK VERSION)
18 PSBX1042Z1 BUTTON, 4KEY (WHITE VERSION)
18 PSBX1042Z2 BUTTON, 4KEY (BLACK VERSION)
19 PSBX1052Z3 BUTTON, 15KEY (WHITE VERSION)
19 PSBX1052Z4 BUTTON, 15KEY (BLACK VERSION)
20 PSSX1006Y KEY SWITCH
21 PSBE1001Z1 BUTTON, ADJUST (WHITE VERSION)
21 PSBE1001Z2 BUTTON, ADJUST (BLACK VERSION)
22 PSQA2021Z LABEL, NOTE
23 PSGP1024X1 PANEL, LCD (WHITE VERSION)
23 PSGP1024X2 PANEL, LCD (BLACK VERSION)
24 PSGG1005Y1 GRILLE (WHITE VERSION)
24 PSGG1005Y2 GRILLE (BLACK VERSION)
25 PSBX1044Z1 BUTTON, 3KEY (WHITE VERSION)
25 PSBX1044Z2 BUTTON, 3KEY (BLACK VERSION)
26 PSBC1013Z1 BUTTON, SHIFT (WHITE VERSION)
26 PSBC1013Z2 BUTTON, SHIFT (BLACK VERSION)
27 PSSX1007Y KEY SWITCH
28 PSJE1011Z FLAT CABLE
29 PSKF1025Y1 CABINET, GRILL LOWER (WHITE VERSION)
29 PSKF1025Y2 CABINET, GRILL LOWER (BLACK VERSION)
30 PSJJ1T017Z JACK, TEL.
31 PSKF1024M1 CABINET, LOWER (WHITE VERSION)
31 PSKF1024M2 CABINET, LOWER (BLACK VERSION)
32 PSKL1005X1 STAND (WHITE VERSION)
32 PSKL1005X2 STAND (BLACK VERSION)
33 PSHA1002Z RUBBER PARTS, FOOT
34 PSGT2174Z NAME PLATE (WHITE VERSION)
34 PSGT2176Z NAME PLATE (BLACK VERSION)
35 PSBD1012Z1 COVER, SWITCH

36
14.2. ACCESSORIES AND PACKING MATERIALS
Ref. No. Part No. Part Name & Description Remarks
A1 PQJX2PS409Z HANDSET (WHITE VERSION)
A1 PQJX2PM409Z HANDSET (BLACK VERSION)
A2 PSJA1043Z CORD, HANDSET (WHITE VERSION)
A2 PSJA1043Y CORD, HANDSET (BLACK VERSION)
A3 PQJA48W CORD, TEL.
A4 PSGD1040Z CARD OVELAY S
A5 PSQX1525X INSTRUCTION BOOK
P1 PSPK1906Z GIFT BOX (WHITE VERSION)
P1 PSPK1909Z GIFT BOX (BLACK VERSION)
P2 PQPP170Z PROTECTION COVER

14.3. MAIN BOARD PARTS

Ref. No. Part No. Part Name & Description Remarks
PCB1 PSWP1T7453UK MAIN BOARD ASS'Y (RTL)
(ICS)
IC1 PSVIBU65050D IC
IC2 PSVITC5324F2 IC
IC3 PQVIMC34119D IC
IC6 PSVI40612A04 IC
IC7 PQVINJU7660M IC S
IC8 PQVINJM2904M IC
IC9 PSVIBA05FP IC
IC10 PSVIBA05FP IC
IC11 PQVINJM319V IC
SW1 PSVII24015T IC
(TRANSISTORS)
Q1 2SA1576Q TRANSISTOR(SI)
Q2 2SA1576Q TRANSISTOR(SI)
Q3 PQVTDTA143XU TRANSISTOR(SI)
Q4 PQVTDTA143XU TRANSISTOR(SI)
Q5 PQVTDTA143XU TRANSISTOR(SI)
Q6 PQVTDTA143XU TRANSISTOR(SI)
Q7 PQVTDTA143XU TRANSISTOR(SI)
Q8 PQVTDTA143XU TRANSISTOR(SI)
Q9 PQVTDTA143XU TRANSISTOR(SI)
Q10 PQVTDTA143XU TRANSISTOR(SI)
Q11 PQVTDTA143XU TRANSISTOR(SI)
Q12 PQVTDTA143XU TRANSISTOR(SI)
Q13 PQVTDTD133HK TRANSISTOR(SI)
Q14 PQVTDTD133HK TRANSISTOR(SI)
Q15 PQVTDTD133HK TRANSISTOR(SI)
Q16 PQVTDTD133HK TRANSISTOR(SI)
Q17 PQVTDTD133HK TRANSISTOR(SI)
Q18 PQVTDTD133HK TRANSISTOR(SI)
Q23 UN5213 TRANSISTOR(SI) S
Q24 PQVTDTA143XU TRANSISTOR(SI)
Q25 2SC4081Q TRANSISTOR(SI)
Q27 2SA1576Q TRANSISTOR(SI)
Q28 UN5213 TRANSISTOR(SI) S
Q29 UN5213 TRANSISTOR(SI) S

37
Ref. No. Part No. Part Name & Description Remarks
Q30 2SA1576Q TRANSISTOR(SI)
Q31 PQVTFB1J3P TRANSISTOR(SI)
(DIODES)
D1 PQVDS1ZB60F1 DIODE(SI)
D3 RLS71 DIODE(SI)
D4 RLS71 DIODE(SI)
D5 RLS71 DIODE(SI)
D6 RLS71 DIODE(SI)
D7 RLS71 DIODE(SI)
D8 RLS71 DIODE(SI)
D9 RLS71 DIODE(SI)
D10 RLS71 DIODE(SI)
D11 PSVDUDZ39B DIODE(SI)
D12 RLS71 DIODE(SI)
D13 RLS71 DIODE(SI)
D17 RLS71 DIODE(SI)
(LEDS)
D100 PSVD2SRVGCT LED
D101 PSVD2SRVGCT LED
D102 PSVD2SRVGCT LED
D103 PSVD2SRVGCT LED
D104 PSVD2SRVGCT LED
D105 PSVD2SRVGCT LED
D106 PSVD2SRVGCT LED
D107 PSVD2SRVGCT LED
D108 PSVD2SRVGCT LED
D109 PSVD2SRVGCT LED
D110 PSVD2SRVGCT LED
D111 PSVD2SRVGCT LED
D112 PSVD2SRVGCT LED
D113 PSVD2SRVGCT LED
D114 PSVD2SRVGCT LED
D115 PSVD2SRVGCT LED
D116 PSVD2SRVGCT LED
D117 PSVD2SRVGCT LED
D118 PSVD2SRVGCT LED
D119 PSVD2SRVGCT LED
D120 PSVD2SRVGCT LED
D121 PSVD2SRVGCT LED
D122 PSVD2SRVGCT LED
D123 PSVD2SRVGCT LED
D124 PSVD1SRCT LED
D125 PSVD1SRCT LED
D126 PSVD1SRCT LED
D127 PSVD1SRCT LED
D128 PSVD1SRCT LED
D129 PSVD1SRCT LED
D130 PSVD1VGCT LED
(CONNECTORS)
CN1 PSJP03A05Z CONNECTOR, 3P
CN2 PSJS36A61Z CONNECTOR, 36P
CN3 PSJP02A05Z CONNECTOR, 2P
CN4 PSJP02A05Z CONNECTOR, 2P
CN5 PSJP04A05Z CONNECTOR, 4P
(CERAMIC FILTER)
X3 PQVBTCS4.00M CERAMIC FILTER
(COIL)

38
( )

39
Ref. No. Part No. Part Name & Description Remarks
L1 PQLQR1LT COIL
L2 PQLQR1LT COIL
L5 PQLQR1RM601 COIL
L6 PQLQR1RM601 COIL
L9 PQLQR1LT COIL
(CRYSTAL OSCILLATORS)
X1 PSVCCR1638B7 CRYSTAL OSCILLATOR
X2 PSVCCR1228B7 CRYSTAL OSCILLATOR
(JACKS)
JK1 PSJJ1T011Z JACK
JK2 PSJJ1T012Z JACK

(TRANSFORMER)
T1 PSLT9Z4A TRANSFORMER
(RESISTORS)
JP3 PQ4R18XJ000 0
JP5 PQ4R18XJ000 0
JP7 PQ4R18XJ000 0
JP14 ERJ3GEY0R00 0
JP15 ERJ3GEY0R00 0
JP16 PQ4R18XJ000 0
J17 ERJ3GEY0R00 0
L7 PQ4R10XJ000 0
L8 PQ4R10XJ000 0
L10 ERJ3GEY0R00 0
L11 ERJ3GEY0R00 0
L12 ERJ3GEY0R00 0
L13 ERJ3GEY0R00 0
L14 ERJ3GEY0R00 0
L15 ERJ3GEY0R00 0
L16 ERJ3GEY0R00 0
L17 ERJ3GEY0R00 0
R1 ERJ3GEYJ472 4.7K
R2 ERJ3GEYJ472 4.7K
R3 ERJ3GEYJ472 4.7K
R4 ERJ3GEYJ330 33
R5 ERJ3GEYJ471 470
R6 ERJ3GEYJ472 4.7K
R7 ERJ3GEYJ330 33
R8 ERJ3GEYJ472 4.7K
R9 ERJ3GEYJ472 4.7K
R10 ERJ3GEYJ472 4.7K
R11 ERJ3GEYJ472 4.7K
R12 ERJ3GEYJ472 4.7K
R13 ERJ3GEYJ472 4.7K
R14 ERJ3GEYJ122 1.2K
R15 ERJ3GEYJ682 6.8K
R16 ERJ3GEYJ470 47
R17 ERJ3GEYJ221 220
R18 ERJ3GEYJ470 47
R19 ERJ3GEYJ221 220
R20 ERJ3GEYJ470 47
R21 ERJ3GEYJ221 220
R22 ERJ3GEYJ470 42
R23 ERJ3GEYJ221 220
R24 ERJ3GEYJ221 220
R25 ERJ3GEYJ470 47

40
41
Ref. No. Part No. Part Name & Description Remarks
R26 PQ4R18XJ100 10
R27 ERJ3GEYJ102 1K
R28 ERJ3GEYJ105 1M
R29 ERJ3GEYJ561 560
R30 ERJ3GEYJ151 150
R31 ERJ3GEYJ103 10K
R32 ERJ3EKF9102 91K
R34 ERJ3GEYJ105 1M
R35 ERJ3GEYJ822 8.2K
R36 ERJ3GEYJ222 2.2K
R38 ERJ3GEYJ222 2.2K
R39 ERJ3GEYJ224 220K
R40 ERJ3GEYJ222 2.2K
R41 ERJ3GEYJ472 4.7K
R42 ERJ3GEYJ103 10K
R43 ERJ3GEYJ102 1K
R44 ERJ3GEYJ183 18K
R45 ERJ3GEYJ103 10K
R46 ERJ3GEYJ392 3.9K
R56 PQ4R18XJ390 39
R57 ERJ3GEYJ124 120K
R58 ERJ3GEYJ564 560K
R59 ERJ3GEYJ332 3.3K
R60 ERJ3GEYJ151 150
R67 ERJ3GEYJ222 2.2K
R68 ERJ3GEYJ222 2.2K
R69 PQ4R18XJ3R3 3.3
R83 ERJ3GEYJ104 100K
R84 ERJ3GEYJ103 10K
R85 ERJ3GEYJ103 10K
R86 ERJ3GEYJ103 10K
R87 ERJ3GEYJ104 100K
R88 ERJ3GEYJ333 33K
R89 ERJ3GEYJ223 22K
R90 ERJ3GEYJ183 18K
R91 ERJ3GEYJ103 10K
R92 ERJ3GEYJ105 1M
R93 ERJ3GEYJ223 22K
R94 ERJ3GEYJ223 22K
R95 ERJ3GEYJ223 22K
R96 ERJ3GEYJ223 22K
R97 ERJ3GEYJ223 22K
R98 ERJ3GEYJ223 22K
R99 ERJ3GEYJ223 22K
R100 ERJ3GEYJ223 22K
R101 ERJ3GEYJ472 4.7K
R102 ERJ3GEYJ472 4.7K
R103 ERJ3GEYJ104 100K
R104 ERJ3GEYJ472 4.7K
R105 ERJ3GEYJ472 4.7K
R106 ERJ3GEYJ154 150K
R107 ERJ3GEYJ104 100K
R108 ERJ3GEYJ563 56K
R109 ERJ3GEYJ123 12K
R110 ERJ3GEYJ223 22K
R113 ERJ3GEYJ680 68
R114 ERJ3GEYJ102 1K

42
43
Ref. No. Part No. Part Name & Description Remarks
R116 ERJ3GEY0R00 0
R117 ERJ3GEYJ473 47K
R118 ERJ3GEYJ473 47K
R119 ERJ3GEY0R00 0
R120 ERJ3GEY0R00 0
R121 ERJ3GEYJ101 100
R123 ERJ3GEYJ223 22K
R124 ERJ3GEYJ223 22K
R125 ERJ3GEYJ223 22K
R126 ERJ3GEYJ223 22K
R127 ERJ3GEYJ102 1K
R128 ERJ3GEYJ102 1K
R129 ERJ3GEYJ473 47K
R130 ERJ3GEYJ182 1.8K
R131 ERJ3GEYJ330 33
R132 ERJ3GEYJ330 33
R133 PQ4R18XJ100 10
R134 ERJ3GEYJ330 33
R135 ERJ3GEYJ330 33
R136 ERJ3GEY0R00 0
R138 ERJ3GEYJ104 100K
R139 ERJ3GEYJ103 10K
R140 ERJ3GEYJ103 10K
R141 ERJ3GEYJ271 270
R144 ERJ3GEYJ330 33
R145 ERJ3GEYJ330 33
R146 ERJ3GEYJ330 33
R147 ERJ3GEYJ330 33
R148 ERJ3GEYJ330 33
R149 ERJ3GEYJ330 33
R150 ERJ3GEYJ330 33
R151 ERJ3GEYJ330 33
R152 ERJ3GEYJ330 33
R153 ERJ3GEYJ330 33
R160 ERJ3GEYJ104 100K
(CAPACITORS)
C2 ECEV1HA2R2N 2.2
C3 PSCEV1HA010 1
C4 ECUV1H680JCV 68P
C5 ECUV1H101JCV 100P
C6 ECUV1H680JCV 68P
C7 ECUV1H101JCV 100P
C8 ECUV1H470JCV 47P
C9 ECUV1H470JCV 47P
C10 PSCEV1EA101 100
C11 PQCUV1E104MD 0.1 S
C12 PSCEV1EA101 100
C13 PQCUV1E104MD 0.1 S
C14 PSCEV1HA010 1
C15 PSCEV0JA102 1000
C16 PSCEV0JA102 1000
C17 PQCUV1E104MD 0.1 S
C18 ECUV1H080DCV 8P
C19 ECUV1H470JCV 47P
C21 ECUV1H104ZFV 0.1 S
C22 ECUV1H104ZFV 0.1 S
C23 PSCEV0JA470 47

44
Ref. No. Part No. Part Name & Description Remarks
C25 ECUV1H470JCV 47P
C26 ECUV1H080DCV 8P
C27 ECUV1H104ZFV 0.1 S
C28 PQCUV1C334ZF 0.33
C31 PQCUV1C334ZF 0.33
C32 PSCEV0JA220 22
C33 PQCUV1E104MD 0.1
C34 PSCEV0JA470 47
C35 PSCEV0JA470 47
C36 PSCEV1HA100 10
C37 PSCEV0JA220 22
C39 PSCEV0JA471 470
C40 PQCUV1E681MB 680
C41 PQCUV1C334KB 0.33
C42 PSCEV1HA010 1
C43 PQCUV1E473MD 0.047 S
C61 PSCEV0JA102 1000
C62 PQCUV1E104MD 0.1
C63 PSCEV1HA100 10
C71 PQCUV1E473MD 0.047 S
C72 PQCUV1E473MD 0.047 S
C73 PSCEV1EA4R7 4.7
C74 PQCUV1E104MD 0.1 S
C78 ECUV1E102JCV 0.001
C79 ECUV1E102JCV 0.001
C80 PSCEV1HA010 1
C82 PSCEV0JA101 100
C83 PSCEV0JA101 100
C84 PSCEV0JA220 22
C85 ECUV1H683MD 0.68
C88 PSCEV1HA100 10
C89 PSCEV0JA220 22
C106 PSCEV0JA101 100
C107 PSCEV0JA101 100
C108 ECUV1H471JCV 470P
C111 ECUV1H104ZFV 0.1
C115 ECUV1H104ZFV 0.1 S
C117 ECUV1H104ZFV 0.1 S
C118 ECUV1H104ZFV 0.1 S
C119 ECUV1H104ZFV 0.1 S
C120 PSCEV0JA470 47
C121 PQCUV1C474ZF 0.47
C122 ECUV1H151JCV 150P

14.4. LCD BOARD PARTS

45
Ref. No. Part No. Part Name & Description Remarks
PCB2 PSWP2T7453UK LCD BOARD ASS'Y (RTL)
(ICS)
IC201 PSVILC7931D IC
IC202 PSVI44780B24 IC
(LED)
D201 PSVD111R820R LED
D202 PSWE1013Z BACKLIGHT
(CONNECTOR)
CN201 PSJS36A61Z CONNECTOR, 36P
(SWITCH)
SW1 PSSS3A101Z SWITCH, BACKLIGHT
(RESISTORS)
R201 PQ4R10XJ222 2.2K
R202 PQ4R10XJ222 2.2K
R203 PQ4R10XJ222 2.2K
R204 PQ4R10XJ222 2.2K
R205 PQ4R10XJ393 39K
R206 PQ4R10XJ104 100K
R207 PQ4R10XJ391 390
R208 PQ4R10XJ102 1K
(CAPACITORS)
C200 PQCUV1E104MD 0.1 S
(OTHERS)
E1 L5ADBKD00002 LIQUID CRYSTAL DISPLAY
E2 PSSE1011Z CONNECTOR
E3 PSHR1132Y GUIDE

14.5. SWITCH BOARD PARTS

Ref. No. Part No. Part Name & Description Remarks
PCB3 PSWP3T7431UK SWITCH BOARD ASS'Y (RTL)
(SWITCH)
SW301 PSSRCA101Z SWITCH, JOG DIAL
(CONNECTOR)
CN301 PSJS03Q36Z CONNECTOR, 3P

15. PRINTED CIRCUIT BOARD

15.1. MAIN BOARD (COMPONENT VIEW)
15.2. MAIN BOARD (BOTTOM VIEW)

16. SCHEMATIC DIAGRAM

17. PRINTED CIRCUIT BOARD
H KXT7453MUK / KXT7453MBUK

46
 1AP
T1 TEL JACK
SPEAKER
IC3 RX RX DATA JK1
Amp COMMUNI-
IC2(TEL Communication LSI) TX TX PBX
MIC CATION
CODEC (D A/A D) IC11,Q1,Q2
SP-Phone CIRCUIT
HANDSET CIRCUIT x2 POWER REGULATOR D1
TONE GENELATOR
JK2 +5V IC9 + ~
GATE
ARRAY x1 - ~
12.288 16.384
IC1 Main p.c.board
MHz MHz
DPITS +5V IC10
HANDSET communi
-cation
-5V IC7 DC-DC
LED
CONVERTER
INT, Control
RD,WT,ALE, JOG SW
D5~D7 Control LED LED
R0~R9
TONE
IC6 DRIVING
DETECT
D100~130
2AP IC8 CPU
Q3~Q12
LCD p.c.board C0~C5
Q13~Q18
INT,
LCD RD,WT,
CONT A0,A1, PI NI
D0~D3
LCD LCD CN2
PANEL CONTROLER x1
RR,RD,RB
T7453
(16x3)
4MHz

LCD +5V
RR,RD,RB
DRIVER
KEY
RESET CK2K

KEY
HOOK SW 3AP
SW301
JOG SW
1 5

2 6

3 7

4 8
9 13

10 14

11 15

16

12
17 21

18 22

19 23

24

20
33

25 32

34

35

36
 MW MUTE
CO24 CO18 CO12 CO6 TRANS

D105 D111 D117 D123

D129 D127

R98 C115
C74 C31 C122
C28
R32 R31

CO23 CO17 CO11 CO5 PAUSE

AUTO FLASH

D104 D110 D116 D122

D128
R124
R123 R126
R125

CO22 CO16 CO10 CO4 PROG

D103 D109 D115 D121

R45 R44 3 6 9 # SP-PHONE

R147 R145 R152 R46
R148 R150 Q25
R146 R153 R151 D11
R41

D124
CO21 CO15 CO9 CO3 FWD/DND

D102 D108 D114 D120

D126

J17 C9
L10 R11 R8 R12
2 5 8 0 HOLD
R13

CO20 CO14 CO8 CO2 CONF

D101 D107 D113 D119

D125

1 4 7 REDIAL
CO19 CO13 CO7 CO1 INT

D100 D106 D112 D118

D130
 E8 E4
E3
B6
CN1 R120 R127 D3 D20 D4 D19 D5 D18 D6 D17 D7 D16 D8 D15 D9 D14 D10 D13
C36 C79
R117 R101
C77 R104
PO R118 E5 F8 E2 E1
C35 C76 Q27
C78 R102 Q30
C108 GND2 R128 R105
R38 C33 NI R103 R96
R106
R35 R39 C117
R119 Q28 R95
C27 Q29 R93 F7 R97 36 35
R133 R107
C120 60 46 R108 R94 R110 R99
C34 R114 64 49
R36 R109 1 48
1 45 R100
F2 C88 X3 R92
C37 CN2
C119
IC6
R40 C118 IC2
R139
R140
C22
16 33
15 31 C21 17 32
R121 2 1
16 30
C23 B5
R131 R132
M2 R122 C24 C25 R34 C26 C16
R61 A4 A3 B4
R135 R43
1 F3 C113 C112
CN4 Q19 R26
2 C44 Q26 C73 X2 F1 Q18 Q15
R82 V2 Q6
D2 AG2 Q20 R81 R25 R24
R23 Q9 R19
Q11 Q8 Q17 Q14
1 14 C15 Q12 Q10 R22 Q5
C43 C70 Q21 R80 A7 R21 B1
JP15 A8 A5 R20 R18 Q16
R67 Q13
C62 IC12 Q22 R79 C83 Q7 Q4
C14 Q3
D12 C51 A6
R84 R60 R17
7 8 R14
1 8 C63 C111 R16
R87 L17
C32 R62 C55 IC7
R52 C82 L16
R83 C59 4 5 C107 C106 L11 L15
R15 64 49 L14
1 8 C45 L5 1 48
E6 -5V C6
IC8 R88 C50 1 C7
L13
H C5
4 5 R1 R6
C72 E7 JK1 R144
4 IC1 L12 C4
R86 R91 C68 R149
C60 C116
R90 C69 R27
R85 C71 V1 R134
R89 OHCA2 R58 C114 R115
E8 16 33 R28
R78 R47 R51
1 20 IC10 IC9 C110 17 32
R77 C46 C52 R50 L R141 X1
R75 R48 B3 L6
C48 C49 C54 C67 C11
C20 R2
C19
C65 L4 R113 C17 C18
C86 C13 1 14
1 30 R63 C66
C57 C38 C64 IC5 R10 C8 R160
R55 R64 R49 IC11 Q1
L1 R3 Q2
C47 R66 R73 R111 R54 7 8
IC4 C12 C10 L2 C1 R9
R76 R65 R53 D1 C3
10 11
R37 R112 6 5 4
R74 15 16 C61 R5
GND R4
R69 R7 CN5
R70 T1
C2
C53 M1 1
OHCA1 F4 C80
R71 A9 F5
C56 C81 AG1 R30 10 1
R72 R68 L8
JK2 JP1
CN
HK

R42 R58 C89 A10

AL

C30
X
C

C42 C41 D22 L9 JP5 R130 JP16

JP6 JP7 JP8 JP2 JP3 JP4
1 8
RU

NZ
CE

36
M

SP2+ A2
IC3 R56 1 2 C121 SP1 Q24
C85 R129 B2
R138 4 5 C39 C84 4 1 SW1
R136 A1
33

R57 CN3 R137

F6 Q31 R29 L7 Q32
R59 C40 SP2- R116
 R[63]
R[62]
R[61]
R[60]

R[31]
R[30]
C200

D[2]
+5V
R206 0.1
100K

46
45
44
43
42
41
40
39
36
37
38

25

24

23

33
OSC1
OSC2

GND
RS
R/W

VCC
D7
D6
D5
D4
D3
D2
D1
D0

E
LCD DRIVER

IC202
COM16
COM15
COM14
COM13
COM12
COM11
COM10

SEG10
SEG11
SEG12
SEG13
SEG14
SEG15
SEG16
SEG17
SEG18
SEG19
SEG20
SEG21
SEG22
SEG23
SEG24
SEG25
SEG26
SEG27
SEG28
SEG29
SEG30
SEG31
SEG32
SEG33
SEG34
SEG35
SEG36
SEG37
SEG38
SEG39
SEG40
COM9
COM8
COM7
COM6
COM5
COM4
COM3
COM2
COM1

SEG1
SEG2
SEG3
SEG4
SEG5
SEG6
SEG7
SEG8
SEG9
+5V

CL2
CL1

V5
V4
V3
V2
V1
M

M
9
8
7
6
5
4
3
2
1
22
21
20
19
18
17
16
15
14
13
12
11
10

80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
34
32
31
62
61
60
59
58
57
56
55

54
53
52
51
50
49
48
47

35
30
29
28
27
26
R201
2.2K

R202
2.2K

R203
2.2K
+5V(V1)
R204
2.2K

4.7K

4.7K
R105

R102
R205
2.2K
R104
CN201 CN2
Q30 4.7K
2 2
R101

R106
150K
12K
R109
50V10µ
4.7K

R108
56K
C88
Q27

Q29

R103
100K
+5V

R114
(V1) +5V(V1) Q28

1K

R107
100K
1 1

17 17
-5V
6 6 LCD CONTRAST
11 11 CONTROL
22 22

28 28 RR[70]

29 29 RR[71]

90 CLKSR
RR[72]
LCD
87 CLKLA
30 30

86 GND
89 L/R
94 M

80 96 RR[73]
79 Y1 VCC 31 31

78 Y2 91
77 Y3 M
76 Y4 81
75 Y5 VEE RR[80]
74 Y6
32 32
82
73 Y7 V1 SHIFT MENU1
72 Y8 83 SW50 SW51
71 Y9 V2
70 Y10 84 RR[81]
69 Y11 V3 23 23

68 Y12 85 MENU2
67 Y13 V4 SW52
66 Y14
65 Y15 RR[82]
64 Y16
24 24

63 Y17 MENU3
62 Y18 SW53
61 Y19
60 Y20 RR[83]
59 Y21
25 25
+5V
58 Y22
57 Y23
56 Y24
55 Y25
54 Y26
53 Y27 R[90]
52 Y28
26 26
D202
51 Y29 RD[0]
50 Y30
27 27

49 Y31 D201

(7) (8)
48 Y32
47 Y33
3 3

46 Y34
45 Y35
44 Y36
4 4

43 Y37
42 Y38
LCD DRIVER R[60] R[60]
41 Y39
7 7
R[61] R[61]
Y40 R[62]
8 8
R[62]
9 9
R[63] 10 10
R[63]
SW1
IC201 R[32]
1

13 13

12 12 R[33]
4
3
2

R[31] 16 16 R[31]

40
39 Y41 R[70]
38 Y42
18 18

37 Y43 R[71]
36 Y44
19 19

35 Y45
R207

R208
1K
470

R[72]
34 Y46
20 20

33 Y47 R[73]
32 Y48
21 21

31 Y49 R[30] R[30]

30 Y50
15 15

29 Y51 D[2] D[2]

28 Y52
14 14

27 Y53
26 Y54
33 33

25 Y55 PSUP1178Z
24 Y56
34 34

23 Y57
22 Y58
35 35

21 Y59
20 Y60
36 36

19 Y61
18 Y62
5 5

17 Y63
16 Y64
15 Y65
14 Y66
13 Y67
12 Y68
11 Y69
10 Y70
9 Y71
8 Y72
7 Y73
6 Y74

(2)(3) (4) (5)(6)

5 Y75
4 Y76
3 Y77
2 Y78
1 Y79
Y80
C115

D[2],R[30-31],R[60-63]
0.1

D[5],D[9-12],R[1-3]

KEY SWITCH
X3
4MHZ

CO6 CO5 CO4 CO3 CO2 CO1

R140
D[10]

D[2]

R92
D[9]

D[5]

10K

+5V(V1)
1M Ω
SW6 SW5 SW4 SW3 SW2 SW64 RR[70]
R110 22K
16

15

14

13

12

11

10

GND 8

22K
22K

22K

22K

D13
OSC1

CO12 CO11 CO10 CO9 CO8 CO7

TEST

RE0
D10

D9

D5

D4

D3

D2

D1

D0

RESET
X2

X1

OSC2

C74
0.1

R93
R94
R95

R96

TELTYPE0 D[11]
SW12 SW11 SW10 SW9 SW8 SW7 17 D11 RD1 64
RR[71]
D[12] RD[0]
18 D12 RD0 63
D14
CO18 CO17 CO16 CO15 CO14 CO13 INT[1]
19 D13
24 RB21 62
RB[21]
INT[2]
20 R0
21 RB11 61
RB[11]
TELTYPE1 SW18 SW17 SW16 SW15 SW14 SW13
RR[72] R[1] RB[1]
21 R01 RB01 60
D15 R[2] +5V(V1)
CO24 CO23 CO22 CO21 CO20 CO19 22 R02 VCC 59
R[3]
22K
22K
22K
22K

23 R03 SEL 58
+5V(V1)
IOR R131 33
SW24 SW23 SW22 SW21 SW20 SW19
RR[73] 24 R10 4BIT IC6 RA1 57
IOW R132 33
MICROCOMPUTER
R100
R97
R98
R99

25 R11 RA0 56
D16
TRANS PAUSE PROG FWD CONF INT R[12] R[93]
26 R12 R93 55
R[13] 21 R[92]
27 R13 R92 54
SW30 SW29 SW28 SW27 SW26 SW25 R[20]
RR[80] R[91]
28 R20 R91 53
D17 R[21] R[90]
29 R21 R90 52
1 2 3 4 5 6 D3
R[22] RR[83]
30 R22 R83 51

SW37 SW38 R[23] 23 22 D4 RR[82]

SW33 SW34 SW35 SW36 31 R23 R82 50
RR[81]
D5
R[30] R81 49
RR[81]
32 R30
33 R33

34 R32

35 R31

36 R40

37 R41

38 R42

39 R43

40 R60

41 R61

42 R62

43 R63

44 R70

45 R71

46 R72

47 R73

48 R80

D18
7 8 9
* 0 #

SW41 SW42 SW43 SW44 SW45 SW46

D10

RR[82]
R[60]
R[61]

R[62]

R[63]
R[33]

R[32]
R[31]

D9

D8
D7
D6
R139

10K

D19
REDIAL HOLD SP MW AUTO MUTE FLASH
RR[70]
RR[71]

RR[72]

RR[73]

RR[80]
R[70]

R[71]
R[72]
R[73]

SW31 SW32 SW39 SW40 SW47 SW48 SW49

RR[83]
D[2],R[30-33],R[60-63],R[70-73]
RB[11]

RB[21]

RD[0]
RB[1]
R[91]

R[92]

R[93]

D20
RR[70-73],RR[80-83]
(1)

INT[1-2],IOR,IOW,R[12-13],R[20-23]
RD[1]

RB[1],RB[11],RB[21],RD[0],R[90-93]
 +5V(V1) COMMUNICATION
+5V(V1)
IC2 LSI
R133
10
6 D5V1 15
SP ON : L C119 A5V1 C22
0.1 3 AG1 DG1 12 0.1 6
SP SP OFF : H

6.3V47µ

47 µ
C23
1 7 A5V2 D5V2 31
C118 C21
0.1 9 DG2 28 0.1
2 AG2
46 A5V3 P/-S 10

C34
560K

0.33
R58
C117

C28
R42 IC3
+5V(V2) 0.1 50
AG3 TEST 45 37
10K
1 8 C84 51 A5V4 24 DG
CD VO2 -FSYNC
6.3V22
SP-PHONE

R56
C27

39
2 7 0.1 58
FC2 GND AG4 C116
3 6 2 22
FC1 VCC VREFDA RXD

R31
R138 AG

10K
4 5 23 R135
Vin VO1 C120 TXD
100K 6.3V47µ 33

470 µ
5

C39

C24
R57 HO-
AG2

50V1µ

0.33
C41
4

C42
120K HO+
+5V(V2)

3.3K
60 BCLK 25

R59
APMN

0.068
C40

150
1 HCLK 26

R60
APNP

C85
680P R32 C25
C122 47P
91K 59 OSC1 29
150P APNO

12.288M
C31 47

R34
2.2K
C32

1M
AG H1

R67

X2
(2)

6.3V22µ JP14 0.33 C26

8 SPO OSC2 30
MIC JP15 0
AG C43 R43 8P
1
55 AP1MN 33 1K
0 0.047 R35 8.2K 56 33

C44
D[11]

D2
2 AP1MP ALE
C108 R39
34
470P 220K 54 AP1MO -INT 44 R[1]

R36
2.2K
R29
560 AG
49 M1 -WR/STB 34 35 R[3]
C33
L7

JK2

2.2K
0

R38
0.1 52 -RD/SDO 35 D[12]
AP2MO
SP 3 53 D7/SFT 36 36 D[10]
C121 AP2MI
0.47
2 57 VREFM D6/SD1 37 D[9]
L8 +5V(V2) Q31
MIC 1 2.5V D5/WBR 38 R[2]

6.3V22µ

6.3V47µ
0

C35
150

C37
C30

R30

4
D22

+5V(V2)
IC8 48 D4/OPC 39
6.3V22µ

AG4 VBB
HAND SET

50V10 µ
L9

C89

40

8
D3/OPB

C36
R68
2.2K
JACK

2.2K
R40
AG D2/OPA 41
AG AG AG3
21 OP7 D1/OP9 42
20 OP6 D0/OP8 43

TONE DETECTION CIRCUIT 19 OP5

TONE INPUT : L C71 C72 18 OP4
NO TONE :H +5V(V2)
0.047 0.047 +5V(V2) 17 OP3
16

100K
R83
R88 33K OP2

R90
18K
22K
R89
(5)

R85 14
R84 10K 6 OP1
Q23 IC8 2 7 11 D[5]
10K 13 RESET
1 5 OP0
IC8
3 32
D12 -CE/-DOE

R91
R86

10K
C70
C62
C73

0.1
10K 25V4.7µ
R87
AG 100K AG

DPITS C3 3
GATE ARRAY 1 50V1µ
JK1
IC1 L1
R1 Q1 T1 4 H
40 4.7K R4
TXA 33 Ω 4 1 L
10
R2 L4 PBX
+5V(V1) 50V2.2 µ 3 T
4.7K 5 9 D1 12V
470
100P

C4 C2
C5

R5
C6 68P 2 R

C1
68P R3

0
41 R6 4.7K
1 7
TXB R7
4.7K 33 Ω

JP6
JP8
JP7

JP5
100P

Q2 2 6
C7

+5V(V1) 50V1µ L2
CN5
C80 VREF IC9 JP1
4.7K

IC11 OUT 3 1 IN 1 G
7
R8

9 +5V(V1)
38 6.3V100 µ JP2

25V100µ
2
7
RXA 4.7K 2 R

GND
C11
C106

0.1
10

C10
8 JP3 0
R113 21 R10 3 B
47P
4.7K

+5V(V1)
C8
R9

SXO JP4
68
C20

20 IC10 4 W
SR1
R11
4.7K

19 IC11 OUT 3 1 IN
4 +5V(V2)

25V100 µ
2 JP16
6.3V100 µ

SR0 39 12
GND

R134 15 RXB 4.7K 0

C13
C107

5
0.1

C12
EP2 3
33 L6 18 R13
XDP JACK
4.7K

47P
R12

C9

CK2M +5V(V1)
C110

L5

R141
1 REGULATOR SECTION
270 32 VDD
N.C 31
11 42 VDD 2
N.C 49
60 VDD
N.C
100K
R160

13 +5V(V1) +5V(V2)
+5V(V1)
0.1
C17

EP0 27 IC7
14 IP0
6.8K
R15

1 8
10 EP1 28
R69

3.3

IP1 0.63V
6.3V100 µ

2 7
29
IP2 VREF
C82
6.3V1000

3 6
30
C61
50V1µ

IP3
C14

R14
1.2K

4 5
17 -5V
GND
C83
6.3V100 µ
35
GND AG
64
GND
8
23 CSN
OP0
J17

24
0

R27
OP1 34 1K C18
25 OSO
OP2 8P
L11

R28 X1
0

26
OP3 33 1M 16.384M
OSI
C19
8
L10

47P
0

36
CK16M
37
CK512K
+5V(V2)

C15
R17 220

R19 220

R21 220

R23 220

R24 220

6.3V1000µ
R16 47

R18 47

R20 47

R22 47

R25 47

Q3 LED
50
R0

Q4
51
4 R1 D100 G D101 G D102 G D103 G D104 G D105 G
+5V(V1)
R R R R R R
Q5
52
R137 +5V(V1) R2 CO19 CO20 CO21 CO22 CO23 CO24
(6)

R136 R129 Q6
47K 53
0 +5V(V2) R3 D106 D107 D108 D109 D110 D111
R116 G G G G G G

R130
14 13 Q7
R R R R R R
0 54
Q32 SW1 1.8K
1 2 R4 CO13 CO14 CO15 CO16 CO17 CO18

Q8
22 55
0.6V : OFF HOOK CK2K R5 D112 G D113 G D114 G D115 G D116 G D117 G
3 Q24 R R R R R R
4.5V : ON HOOK Q9
56
R6 CO7 CO8 CO9 CO10 CO11 CO12
HOOK SWITCH
C112

C113

Q10
INT[1] R144 33 11 57
INT0 R7 D118 G D119 G D120 G D121 G D122 G D123 G
IOR R150 33 10
IOR R R R R R R
Q11
R151 33 9 58
15 IOW
IOW R8 CO1 CO2 CO3 CO4 CO5 CO6
R[12] R152 33 7
A0 SP CONF FWD MUTE AUTO MW
17 Q12
R[13] R153 33 6 59
A1 R9 D124 D125 D126 D127 D128 D129
R[20] R145 33 5
16 D0 ICM
R[21] R146 33 4
R121

D130
100

D1
18 R[22] R147 33 3
D2
5 Q13
R[23] R148 33 2 43 L12 33
D3 C0
INT[2] R149 33 12
INT1 Q14
R123 22K

R124 22K

R125 22K
R126 22K

44 L13 33
+5V(V1) C1
+5V(V1)
Q15
45 L14 33
C2
4.7K
R41

19 Q16
(4)

63 RESET 46 L15 33
C3
C111

R44 R45
0.1

Q25
Q17
18K 10K L16 33
50V10 µ

47
3.9K

C63
R46

C4
16 EP3
RESET : H 5V Q18
L17 33
NORMAL : L 0V C5 48
RESET CIRCUIT PI NI
61 62

+5V(V1)
9 +5V(V2)
6.3V1000 µ
(1) (3)

R127

R128
1K

1K

C16
R117

47K
R118
47K

10 Ω

+5V(V1)
R26

11
R119 CN1 CN301 SW301
0 6
2 2 2 JOG[2]
R120 0 IC11
1 1 1 JOG[1] -5V SP-PHONE RECEPTION
C79 C78
1000P 1000P 3 3 3 GND +5V(V2)
(8)

C77 C76 14 SP-PHONE TRANSMISSION

3AP:PSUP1196ZA
7
JOG SWITCH HANDSET RECEPTION
IC12
(7)

1AP:PSUP1177Z
HANDSET TRANSMISSION
 R206
SW1 C201 24 1
80 51 25 80
R201
81 50
R208 R202
R203
R207 IC202
R204
IC201
C200 R205

D202 40 65
100 31
1 30 41 64

35 1
CN201 +5V
36 2

GND

D201

SHIFT

MENU1 MENU2 MENU3

 3

CN301 2

SW301