ST-SB920

SERVICE MANUAL AEP Model

UK Model

SPECIFICATIONS

FM tuner section AM tuner section

Frequency range 87.5 – 108.0 MHz Frequency range MW: 522 – 1,611 kHz (9 kHz step)
Aerial terminals 75 Ω, unbalanced LW: 144 – 288 kHz (1 kHz step)
Intermediate frequency 10.7 MHz Intermediate frequency 450 kHz
Sensitivity at 26 dB quieting Usable Sensitivity (with AM loop aerial)
(mono) 10.3 dBf, 0.9 µV/75 Ω MW: 200 µV/m
at 46 dB quieting LW: 700 µV/m
(stereo) 38.5 dBf, 23 µV/75 Ω Signal-to-noise ratio MW: 54 dB (50 mV/m, 999 kHz)
Usable sensitivity (IHF) 10.3 dBf, 0.9 µV/75 Ω LW: 50 dB (50 mV/m, 216 kHz)
S/N at 40 kHz deviation Harmonic distortion 0.3% (50 mV/m, 400 Hz)
80 dB (mono), 76 dB (stereo) Selectivity 50 dB
Harmonic distortion WIDE
0.035 % (mono), 0.045 (stereo) General
NARROW Power requirements 220 – 230 V, AC 50/60 Hz
0.055 % (mono), 0.075 (stereo) Power consumption 12 W
Frequency response 30 Hz – 15 kHz Input impedance 75 Ω
(+0.3/–0.7 dB) Input connector IEC-male
Separation 50 dB at 1 kHz Dimensions 430 × 86 × 295 mm (w/h/d)
Selectivity at 400 kHz Weight 3.95
WIDE 85 dB Supplied accessories Audio cord (1)
NARROW 90 dB AM loop aerial (1)
at 300 kHz FM wire aerial (1)
WIDE 45 dB EON connecting cord (1)
NARROW 70 dB
Output at 40 kHz deviation 600 mV
Design and specifications are subject to change without notice.

FM STEREO FM-AM TUNER

MICROFILM

Downloaded from www.Manualslib.com manuals search engine

 TABLE OF CONTENTS
SAFETY-RELATED COMPONENT WARNING!!
1. GENERAL ······································································ 2
COMPONENTS IDENTIFIED BY MARK ! OR DOTTED LINE WITH
2. TEST MODE ·································································· 3 MARK ! ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
3. ELECTRICAL ADJUSTMENT ································· 5 APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
4. DIAGRAMS
4-1. Circuit Board Location ······················································· 8
MODEL IDENTIFICATION
4-2. Schematic Diagram – DISPLAY SECTION – ·················· 9
4-3. Printed Wiring Board – DISPLAY SECTION – ············· 11 — BACK PANEL —
4-4. Printed Wirng Board – TUNER SECTION – ················· 13
4-5. Schematic Diagram – TUNER SECTION (1/2) – ·········· 15
4-6. Schematic Diagram – TUNER SECTION (2/2) – ·········· 17
4-7. IC Pin Function ································································ 19
4-8. IC Block Diagram ···························································· 20 yyyyyyyy
,,,,,,,,

6. EXPLODED VIEWS PART NO.

6-1. Front Panel and Case Section ··········································· 21
PARTS No. MODEL
6-2. Panel and Display Section ················································ 22
4-998-494-0π AEP model
4-998-494-1π UK model
7. ELECTRICAL PARTS LIST ··································· 23

SECTION 1
GENERAL

Location of Controls

1 2 3 4 5 6

789 0!¡ !™!£!¢!∞!§ !¶!• !ª@º @¡

1 POWER swtich (U) !™ MEMORY button

2 SHIFT button !£ BAND button
3 Numeric button !¢ ON/OFF button
4 Display window !∞ ANTENNA button
5 DIRECT button !§ FM MODE button
6 TUNING/SELECT knob !¶ CHARACTER button
7 DISPLAY button !• MENU button
8 PTY button !ª RETURN button
9 TA button @º ENTER button
0 NEWS/INFO button @¡ TUNING MODE button
!¡ AUTO-BETICAL SELECT button

—2—
Downloaded from www.Manualslib.com manuals search engine
 SECTION 2
TEST MODE
1. Circuit Check Mode
Set to the reception frequency that the curcuit can STEREO RDS stations. (Set the input level to above 70 dB.)
This enables circuit check to be performed in any of the reception modes-FM, AM (MW, LW). Set to a desired band before setting the test
mode.

1. Turn OFF the power.

2. While pressing 4 and AUTO-BETICAL SELECT together, turn ON U .

• The items in the following table will be checked automatically in order every 2 seconds.
DISPLAY
Display Items NG
FM RDS AM (MW, LW)
Tuned AST signal = LOW OK or NG IC251 NG, RV251 adjustments
IF Frq IF COUNT OK OK or NG OK or NG FE101, IC251 NG, or IF count buffer amp (Q251, Q401) NG
Sig Level SI LEVELh 70dB OK or NG OK or NG IC221 NG, RV221 adjustments
Stereo ST signal = LOW OK or NG IC301 NG, RV301 adjustments
RDS Signal RDS DATA OK OK or NG IC801 NG

NOTE : The preset data will be erased when this test mode is used. Therefore, take down the data before setting this mode and preset the
data again after completing operations in this mode.

2. Display Tube Check and KEY Check mode

1. Turn OFF the power.

2. While pressing 1 and AUTO-BETICAL SELECT together, turn ON U .
3. While continuously pressing 1 and AUTO-BETICAL SELECT together, check the following.

Microcomputer version indication (1 sec) All light up “7F” Dot area only “60” Dot area only “7E”

Dot area only “5F” Dot area only “3D”

Indication test pattern

1 7F 2 60 3 7E 4 3D 5 5F

* The indication test pattern from 2 to 5 are indicated on only even grids.

The display changes every 1 sec.

4. Release 1 and AUTO-BETICAL SELECT . The KEY CHECK mode will be set.
5. All key numbers will be displayed.
Key Number : 27

6. Each time the key is pressed, the key number will be counted down.
Each key will be counted only once, at the first time.
7. When all keys have been pressed, the process will end.

—3—
Downloaded from www.Manualslib.com manuals search engine
 3. Entering the Factory Preset (In case perform just to write memory of the Factory Preset.)

NOTE : As contents of the Factory Preset will be written into memory after completing this check mode, delete contents of memory
according to 4. Forced RESET.

1. Turn OFF the power.

2. While pressing 3 and AUTO-BETICAL SELECT together, turn ON U .

4. Forced RESET (Used to delete the contents of Factory Preset when it is written into the preset memory.)

Clears all the RAMs and sets the initial state

1. Turn OFF the power.
2. While pressing 5 and AUTO-BETICAL SELECT together, turn ON U .
3. When “All clear” is indicated on the display tube, it means that “Forced Reset” has been completed.

—4—
Downloaded from www.Manualslib.com manuals search engine
 SECTION 3
ELECTRICAL ADJUSTMENTS
Precautions in Repairing FM Discriminator ADJUSTMENT
(NULL and MONO Distortion Adjustment)
If the front end unit fails, it is difficult to repair the inner circuits, so
replace the entire front end unit. Setting:
IF BAND : WIDE
Set “IF : WIDE” after the all adjustments. ANT ATT : OFF

FM SECTION 0dB = 1µV

FM RF SSG
1kHz
highpass distortion meter
FM RF SSG filter
1kHz
highpass distortion meter
filter set

set

FM ANTENNA (75Ω) LINE OUT

FM ANTENNA (75Ω) LINE OUT Modulation : Monaural Standard signal

Output level : 6mV (76dB) (at 75 Ω open)

• Standard Setting of FM Stereo RF Signal Generator. Digital Voltmeter

TP251 (DC range)
MONAURAL NULL terminal
STEREO STANDARD SIGNAL
STANDARD SIGNAL

Carrier frequency : 98MHz Carrier frequency : 98MHz

Modulation : Audio 1kHz Modulation : Audio 1kHz
Main channel (L+R) : 33.75kHz 75kHz deviation Procedure:
deviation 1. Tune the set to 98 MHz.
Sub channel (L–R) : 33.75kHz 2. Adjust IFT252 for 0V reading on the digital voltmeter.
deviation ................... NULL
Pilot : 7.5kHz 3. Adjust IFT253 for a minimum reading on the distortion meter.
Deviation
................... MONO Distortion (THD)
4. Repeat the adjustments of 2 and 3 several times.
How to switch IF BAND : WIDE/NARROW and ANT
ATT : ON/OFF Note : When replacing the ceramic filter, perform this alignment.

Method 1:
1. Set the reception mode to FM.
2. Push the MENU button and turn the TUNING/SELECT to
indicate “Reception” on the fluorecent display tube, then press
the ENTER button.
3. Rotate the TUNING/SELECT knob in the clokwise direction.
(Proceeds onto the step 5 when rotated in the counterclokwise
direction.)
4. Turn the TUNING/SELECT knob to indicate “ANT ATT :
OFF” on the fluorescent display tube, then press the ENTERl
button.
5. Turn the TUNING/SELECT knob to indicate “IF : NARROW”
or “IF : WIDE” on the fluorescent display tube, then press the
lENTER button.
When the IF BAND : NARROW is set, “NARROW” is
indicated on the fluorescent display tube.
6. Set WIDE after the operation.

* When set to standby for inputs using the TUNING/SELECTl

knob, “SELECT” is indicated on the fluorecent display tube.

Method 2:
After the test modes “2. Display Tube Check and KEY Check mode”
or “3. Entering the Factory Preset”, “IF : NARROW” and “IF :
WIDE” are switched every time pressing RETURN button the IF
BAND : NARROW is set “NARROW” is indicated on the
fluorescent display tube.
Likewise, the mode can be switched between “ANT ATT : ON”
and “ANT ATT : OFF”. When set to ANT ATT : ON, the fluorescent
display tube indicates ANT ATT.

—5—
Downloaded from www.Manualslib.com manuals search engine
 Stereo Level Adjustment Stereo Separation Adjustment

Setting: Setting:
IF BAND : WIDE IF BAND : WIDE
ANT ATT : OFF
FM RF SSG
level meter
FM RF SSG

set
set

FM ANTENNA (75Ω) LINE OUT

FM ANTENNA (75Ω) Modulation : Stereo Standard signal
Output level : 6mV (76dB) (at 75 Ω open)
Modulation : Stereo Standard signal
Output level : 18µV (25dB) (at 75 Ω open)
Procedure:
Procedure: 1. Refer to “How to switch IF BAND WIDE/NARROW” on page
1. Tune the set to 98 MHz. 6.
2. Adjust RV251 to the point (moment) when the “STEREO”
indicator will change from going off to going on. FM stereo
Level meter Level meter
Signal generator
connection reading (dB)
Narrow Gain Adjustment Output channel
L-CH L-CH A
Setting: B
IF BAND : NARROW R-CH L-CH Adjust RV301 for minimum
ANT ATT : OFF reading on Level meter
R-CH R-CH C
FM RF SSG
D
L-CH R-CH Adjust RV301 for minimum
reading on Level meter
set

L-CH Stereo separation : A – B

R-CH Stereo separation : C – D
FM ANTENNA (75Ω)
The separations of both channels should be equal.
Modulation : Stereo Standard signal
Output level : 18µV (25dB) (at 75 Ω open)

Procedure:
1. Tune the set to 98 MHz.
2. Set “IF BAND : NARROW” according to the procedure of
“How to switch IF BAND WIDE/NARROW” on page 6.
3. Adjust RV231 to the point (moment) when the “STEREO”
indicator will change from going off to going on.

FM Meter Level Adjustment

Setting:
IF BAND : WIDE
ANT ATT : OFF
FM RF SSG

set

FM ANTENNA (75Ω)

Modulation : Stereo Standard signal

Output level : 3mV (76dB) (at 75 Ω open)

Procedure:
1. Tune the set to 98 MHz.
2. Press DISPLAY button to display the digital signal, then adjust
RV221 to be display as “SIG 70dB”.

—6—
Downloaded from www.Manualslib.com manuals search engine
 AM SECTION
AM Meter Level Adjustment

Setting:
BAND : LW
loop antenna
loop antenna (Supplied accessories)

AM RF SSG

set

30% amplitude AM antenna

60 cm terminal (TM1)
modulation by
400 Hz signal Field strength dB (µV/m) =SSG output level dB (µV/m) –26 dB.
Carrier frequency : 216kHz
Modulation : AUDIO 400Hz, 30% modulation

Procedure:
1. Set AM RF signal generator so that the AM antenna input level
becomes 74dBµ/m.
2. Adjust RV402 so that 1 to 10 indication bars light up on the
signal meter.

Adjustment Location

[TUNER BOARD] — Component Side —

FE101

RV301
Stereo RV402
Separation AM Meter Level
IFT252, 253
FM Discriminator
TP251 (NULL)
IFT253
(THD) RV231
Narrow Gain
CNP702 IFT252 RV221
(NULL) FM Meter Level
1 8 RV251
Stereo Level

—7—

Downloaded from www.Manualslib.com manuals search engine

 THIS NOTE IS COMMON FOR PRINTED WIRING For printed wiring boards.
BOARDS AND SCHEMATIC DIAGRAMS. Note:
(In addition to this, the necessary note is printed in • X : parts extracted from the component side.
each block.) • b : Pattern from the side which enables seeing.

For schematic diagrams. • Indication of transistor

Note:
• All capacitors are in µF unless otherwise noted. pF: µµF 50 WV
or less are not indicated except for electrolytics and tantalums.
• All resistors are in Ω and 1/4 W or less unless otherwise speci- BC E
fied.
These are omitted
• ¢ : internal component.
• C : panel designation
Note:
The components identified by mark ! or dotted line with
mark ! are critical for safety. • Waveforms
Replace only with part number specified.

• U : B+ Line.
1 IC801 !£ OSC1
• V : B– Line.
• Voltages and waveforms are dc with respect to ground under 3.6 Vp-p
no-signal (detuned) conditions.
no mark : FM
( ) : MW 4.332MHz
< > : LW
∗ : Impossible to measure 2 IC701 !¡ X2
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production tol-
erances. 5.2 Vp-p
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production tol- 4.19MHz
erances.
• Circled numbers refer to waveforms.
• Signal path.
F : FM
f : AM

SECTION 4
DIAGRAMS
4-1. CIRCUIT BOARDS LOCATION

TRANS board

POWER SW board
TUNER board

DISPLAY board

ENCODER board

Downloaded from www.Manualslib.com manuals search engine

—8—
 ST-SB920
4-2. SCHEMATIC DIAGRAM – DISPLAY SECTION – • See page 8 for Waveforms. • See page 19 for IC Pin Function.

—9— — 10 —

Downloaded from www.Manualslib.com manuals search engine

 ST-SB920
4-3. PRINTED WIRING BOARD – DISPLAY SECTION – • See page 8 for Circuit Boards Location.

1 2 3 4 5 6 7 8 9 10 11 12 13 14

TUNER BOARD
CNP702
A
ENCODER A
BOARD DISPLAY BOARD
1-668-809-
31 30
8 1
TUNING/SELECT
B 50

51 1
9 1

100
1 3
1 2 3
11 FL701 FLUORESCENT INDICATOR TUBE 80 81
TUNING
C (11) MODE
DIRECT 0 9 8 7 6 5 4 3 2 1 SHIFT

11
ENTER RETURN MENU CHARACTER FM MODE ANTENNA ON/OFF BAND MEMORY AUTO-BETICAL NEWS TA PTY DISPLAY (11)
SELECT /INFO 1-668-809-
D
B
TUNER BOARD
CNP701

E
TRANS BOARD
POWER SW BOARD • Semiconductor
CN951 Location
ECP900 2 2
5 Ref. No. Location
11
F 1 1 S901 D701 C-13
C 1-668-810- (11) D702 B-13
TUNER BOARD D703 B-13
CNP952 1 D705 C-13
2
D707 D-13
AC
IN
IC701 B-9
1
11 IC702 B-11
G 1-669-149-
16 (11)
Q701 C-13

— 11 — — 12 —

Downloaded from www.Manualslib.com manuals search engine

 ST-SB920
4-4. PRINTED WIRING BOARD – TUNER SECTION – • See page 8 for Circuit Boards Location.

1 2 3 4 5 6 7 8 9 10 11 12 13
TUNER BOARD
A ANTENNA LINE OUT
TM401 CNJ301
A FM 750 B R L • Semiconductor
COAXIAL
Location
EON CONTROL
OUT Ref. No. Location

E
D221 H-3
FE101 D251 H-9
B FM FRONT END E E D301 C-11
E D371 B-12
FE401
AM FRONT
D401 C-4
END D402 E-4
E
D901 C-8
E
D902 C-8
1 4
D903 C-7
C D904 C-7
8 5 D905 D-7
E D906 H-12
12 22
3 D907 D-7
E 2 D908 C-8
E 1
1 7 11 1
IC221 H-2
D IC251 H-7
20 1
IC301 D-11
IC302 C-10
IC401 D-5
IC801 G-11
IC901 D-8

STEREO Q200 G-3

20 3
E 11 10 E E E
SEPARATION
Q201 H-4
2
Q202 H-4
1 E
17 Q204 H-4
Q205 H-5
E
AM METER Q231 G-5
1 9 LEVEL
Q232 G-5
Q233 G-4
F Q234 H-6
Q235 G-6
Q236 G-6
Q237 G-6
Q251 H-9
1 8 Q301 B-10
10 16
16 9 Q302 B-9
E E E Q303 B-8
G NULL
Q304 B-8
FM METER
LEVEL
Q401 E-6
E E E E TRANS
Q402 C-5
BOARD Q403 C-5
1 8 5
IFT
252
IFT
253 CN952 Q404 D-5
CNP952

16 9 Q405 C-5
1 8
E
E
C Q521 E-8
H 16 9 CNP702 CNP701
1
Q522 E-8
8 1 8 1
Q523 E-8
E E E E Q801 E-11
NARROW STEREO Q901 D-7
GAIN LEVEL
11
IFT252 IFT253
NULL THD 1-668-808- (11)
16
I
A B
DISPLAY BOARD DISPLAY BOARD
CN702 CN701

—13 — — 14 —

Downloaded from www.Manualslib.com manuals search engine

 ST-SB920
4-5. SCHEMATIC DIAGRAM – TUNER SECTION (1/2) – • See page 20 for IC Block Diagrams.

— 15 — — 16 —

Downloaded from www.Manualslib.com manuals search engine

 ST-SB920
4-6. SCHEMATIC DIAGRAM – TUNER SECTION (2/2) – • See page 8 for Waveforms. • See page 20 for IC Block Diagrams.

BUFFER

—17 — — 18 —

Downloaded from www.Manualslib.com manuals search engine

 4-7. IC PIN FUNCTION (DISPLAY BOARD)
• IC701 System Control (µPD780205GF-040-3BA)
Pin No. Pin Name I/O Function
1 VDD — Power supply (+5V).
2 ANT — Not used. (Open)
3 ATT — Not used. (Open)
4 BAND1 — Not used. (Open)
5 BAND2 — Not used. (Open)
6 IF-B — Not used. (Open)
7 NC — Not used. (Open)
8 MONO — Not used. (Open)
9 TUN — Not used. (Open)
10 RESET I System reset input.
11 X2 O Oscillation signal output (4.19MHz).
12 X1 I Oscillation signal input (4.19MHz).
13 GND — Ground.
14 NC — Not used. (Open)
15 LOCK I Lock signal input.
16 VDD — Power supply (+5V).
17 CLK O PLL clock to FE101.
18 DATA O PLL data to FE101.
19 D-IN I PLL data from FE101.
20 CE O PLL Latch to FE101.
21 BLN — Not used. (Open)
22 ST I Stereo display detection.
23 CAL — Not used. (Open)
24 AST I Auto stop signal detection.
25 AVSS — Ground.(Analog)
26 MUTE O Muting signal output.
27 EON O External control.
28 PGM — Not used. (Open)
29 DATA RDS I RDS data input.
30 R2 O Rotary encoder phase detection.
31 KEY 2 I Key input.
32 KEY 1 I Key input.
33 SI I Signal input.
34 AVDD — Analog power supply (+5V).
35 AVREF I Reference voltage (+5V).
36 RIN I Remote control input.
37 R1 I Rotary encoder number of rotation detection.
38 RDS CLK I RDS data clock input.
39 POWER I Power supply ON/OFF monitor.
40 GND — Ground.
41 to 46 IS 1 to 5 I Model detection.
47 to 78 P1 to P32 O Fluorescent indicator tube, segment drive.
79 V LOAD — Power supply (-30V).
80 to 84 P33 to P37 O Drives indication tube.
85 to 100 G1 to G16 O Fluorescent indicator tube, grid drive.

— 19 —
Downloaded from www.Manualslib.com manuals search engine
 4-8. IC BLOCK DIAGRAMS (TUNER BOARD)

IC301 LA3401

MUTE
VCO
+B

ST
22 21 20 19 18 17 16 15 14 13 12
GND IC901 LA5667

LAMP
PLL DRIVE REG

FM/AM SELECT CONTROL MUTING

LOGIC / MUTE ON/OFF OUT CONTROL

FM/AM SELECT REG

MPX
MUTING
GND
1 2 3 4 5 6 7

1 2 3 4 5 6 7 8 9 10 11
AM

FM/AM
R
FM

IC401 LA1245 IC221, IC251 LA1235

20 19 18 17 16 15 14 13 12 11 16 15 14 13 12 11 10 9
B+ B+
(IF)
AM DET MUTING
AM METER CIRCUIT
OSC DRIVE DETUNE
DET
LEVEL METER
DET DRIVE
AGC
IF OFF
AM
AM RF AMP AM IF AMP NULL METER
MIXING
B+ SHORTING
GND (RF)
1 2 3 4 5 6 7 8 9 10 FM IF AMP QUADRATURE AF/NULL
LIMITER DET METER
AF AMP
GND
1 2 3 4 5 6 7 8

IC801 BU1992
TSTLD
OSCO
RDCL

VDDD

TEST
OSCI

VSSD
TS7

16 15 14 13 12 11 10 9

TEST LOGIC AND OUTPUT

SELECTOR SWITCH

OSCILLATOR 57kHz ANTI-

QUALITY BIT RECONSTRUCTION
AND BANDPASS ALIASING
GENERATOR FILTER
DIVIDER (8th ORDER) FILTER

BIPHASE CONTAS LOOP

DEFFERENTIAL CLOCKED
SYMBOL VARIABLE AND
DECODER COMPARATOR
DECODER FIXED DIVIDER

CLOCK REGENERATION
AND SYNC

VP1

REFERENCE
VOLTAGE

1 2 3 4 5 6 7 8
QUAL

RDDA

Vref

MUX

VDDA

VSSA

CIN

SCOUT

— 20 —
Downloaded from www.Manualslib.com manuals search engine
 SECTION 5
EXPLODED VIEWS
NOTE:
• -XX, -X mean standardized parts, so they may • The mechanical parts with no reference number When indicating parts by reference number,
have some differences from the original one. in the exploded views are not supplied. please include the board name.
• Items marked “*” are not stocked since they • Hardware (# mark) list and accessories and
are seldom required for routine service. Some packing materials are given in the last of this The components identified by mark ! or
delay should be anticipated when ordering these parts list. dotted line with mark ! are critical for safety.
items. Replace only with part number specified.
• Color Indication of Appearance Parts
Example:
KNOB, BALANCE (WHITE) . . . (RED)
↑ ↑
Parts of Color Cabinet’s Color

5-1. FRONT PANEL AND CASE SECTION

5
5
b
5
not supplied
6

4
#1
a
#1
#1

PT901 5
8
not
supplied 7 9
12
3
not supplied
11

#1
#1
a

not 10
supplied
#1
#1
#1
#1 b #1
not supplied 2

#2 1

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
1 X-4949-523-1 FOOT ASSY (F50180S) 7 3-703-244-00 BUSHING, CORD
2 4-970-124-01 CUSHION (F50180S) !8 1-575-651-21 CORD, POWER
* 3 3-703-353-06 SUPPORT, PC BOARD !9 1-770-019-11 ADAPTOR, CONVERSION PLUG 3P (UK)
* 4 A-4407-370-A TUNER BOARD, COMPLETE * 10 4-998-494-01 PANEL, BACK (AEP)
5 3-710-901-01 SCREW, TAPPING (SILVER) * 10 4-998-494-11 PANEL, BACK (UK)

5 3-710-901-11 SCREW, TAPPING (BLACK) 11 3-704-515-01 SCREW (BV/RING)

* 6 4-998-495-01 CASE (407026) (BLACK) * 12 1-669-149-11 TRANS BOARD
6 4-998-495-21 CASE (407026) (SILVER) ! PT901 1-423-525-11 TRANSFORMER, POWER

— 21 —
Downloaded from www.Manualslib.com manuals search engine
 5-2. PANEL AND DISPLAY SECTION

rA : ENCODER BOARD (supplied with DISPLAY BOARD)

55 not supplied
60
#1
57 #1 #1

54
56 59
58
#1 FL701

69
53 68

not supplied rA
62 62

64 70
52
#3
#4
63
supplied with RV701
66
supplied with No. 66
51

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
51 4-998-493-01 PANEL, FRONT (BLACK) 62 4-998-485-11 HINGE (SILVER)
51 4-998-493-11 PANEL, FRONT (SILVER) 63 4-998-488-01 BUTTON (C) (BLACK)
52 4-942-568-41 EMBLEM (NO.5), SONY 63 4-998-488-11 BUTTON (C) (SILVER)
53 4-998-489-01 PLATE (C), INDICATION 64 4-998-492-01 DOOR (BLACK)
54 4-998-486-01 BUTTON (A) 64 4-998-492-11 DOOR (SILVER)

55 4-999-566-01 BUTTON (S) 66 4-998-491-01 KNOB (R41) (BLACK)

56 3-024-055-01 BUTTON (POWER)(BLACK) 66 4-998-491-11 KNOB (R41) (SILVER)
56 3-024-055-21 BUTTON (POWER)(SILVER) 68 4-998-487-01 BUTTON (B) (BLACK)
* 57 1-668-810-11 POWER SW BOARD 68 4-998-487-11 BUTTON (B) (SILVER)
* 58 4-998-481-01 INSULATED PLATE (DS) 69 4-998-484-01 SPRING, CLICK

* 59 4-945-292-01 HOLDER,INDICATION TUBE 70 4-998-490-01 BASE, PANEL (BLACK)

* 60 A-4407-371-A DISPLAY BOARD, COMPLETE 70 4-998-490-11 BASE, PANEL (SILVER)
62 4-998-485-01 HINGE (BLACK) FL701 1-517-177-21 FLUORESCENT INDICATOR TUBE

— 22 —
Downloaded from www.Manualslib.com manuals search engine
 SECTION 6
DISPLAY ELECTRICAL PARTS LIST
NOTE:
When indicating parts by reference number, • Due to standardization, replacements in the • RESISTORS
please include the board name. parts list may be different from the parts All resistors are in ohms.
specified in the diagrams or the components METAL: metal-film resistor
The components identified by mark ! or used on the set. METAL OXIDE: Metal Oxide-film resistor
dotted line with mark ! are critical for safety. • -XX, -X mean standardized parts, so they may F: nonflammable
Replace only with part number specified.
have some difference from the original one. • COILS
• Items marked “*” are not stocked since they uH: µH
are seldom required for routine service. Some • SEMICONDUCTORS
delay should be anticipated when ordering these In each case, u: µ, for example:
items. uA...: µA... , uPA... , µPA... ,
• CAPACITORS: uPB... , µPB... , uPC... , µPC... ,
uF: µF uPD..., µPD...
Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
* A-4407-371-A DISPLAY BOARD, COMPLETE R707 1-249-441-11 CARBON 100K 5% 1/4W
*********************** R708 1-249-441-11 CARBON 100K 5% 1/4W
(including ENCODER BOARD) R709 1-247-807-31 CARBON 100 5% 1/4W
R710 1-249-406-11 CARBON 120 5% 1/4W F
* 4-945-292-01 HOLDER, INDICATION TUBE R711 1-249-406-11 CARBON 120 5% 1/4W F
4-998-481-01 INSULATED PLATE (DS)
R712 1-249-407-11 CARBON 150 5% 1/4W F
< CAPACITOR > R713 1-249-408-11 CARBON 180 5% 1/4W F
R714 1-247-815-91 CARBON 220 5% 1/4W
C701 1-162-306-11 CERAMIC 0.01uF 20% 16V R715 1-249-410-11 CARBON 270 5% 1/4W F
C702 1-162-306-11 CERAMIC 0.01uF 20% 16V R716 1-249-411-11 CARBON 330 5% 1/4W
C703 1-162-209-31 CERAMIC 27PF 5% 50V
C704 1-162-209-31 CERAMIC 27PF 5% 50V R717 1-249-413-11 CARBON 470 5% 1/4W F
C705 1-162-306-11 CERAMIC 0.01uF 20% 16V R718 1-249-414-11 CARBON 560 5% 1/4W F
R719 1-249-416-11 CARBON 820 5% 1/4W F
C706 1-164-159-21 CERAMIC 0.1uF 50V R720 1-249-418-11 CARBON 1.2K 5% 1/4W F
C707 1-126-947-11 ELECT 47uF 20% 35V R721 1-249-421-11 CARBON 2.2K 5% 1/4W F
C708 1-162-306-11 CERAMIC 0.01uF 20% 16V
C709 1-162-306-11 CERAMIC 0.01uF 20% 16V R722 1-249-424-11 CARBON 3.9K 5% 1/4W F
C710 1-126-964-11 ELECT 10uF 20% 50V R723 1-249-430-11 CARBON 12K 5% 1/4W
R724 1-247-807-31 CARBON 100 5% 1/4W
C711 1-126-964-11 ELECT 10uF 20% 50V R725 1-249-406-11 CARBON 120 5% 1/4W F
C712 1-104-905-11 CAPACITOR 0.22F 5.5V R726 1-249-406-11 CARBON 120 5% 1/4W F
C713 1-162-306-11 CERAMIC 0.01uF 20% 16V
C714 1-126-959-11 ELECT 0.47uF 20% 50V R727 1-249-407-11 CARBON 150 5% 1/4W F
C717 1-162-286-21 CERAMIC 220PF 10% 50V R728 1-249-408-11 CARBON 180 5% 1/4W F
R729 1-247-815-91 CARBON 220 5% 1/4W
< FILTER > R730 1-249-410-11 CARBON 270 5% 1/4W F
R731 1-249-411-11 CARBON 330 5% 1/4W
FL701 1-517-177-21 INDICATOR TUBE, FLUORESCENT
R732 1-249-413-11 CARBON 470 5% 1/4W F
< DIODE > R733 1-249-414-11 CARBON 560 5% 1/4W F
R734 1-249-416-11 CARBON 820 5% 1/4W F
D701 8-719-991-33 DIODE 1SS133T-77 R735 1-249-418-11 CARBON 1.2K 5% 1/4W F
D702 8-719-991-33 DIODE 1SS133T-77 R736 1-249-421-11 CARBON 2.2K 5% 1/4W F
D703 8-719-991-33 DIODE 1SS133T-77
D705 8-719-991-33 DIODE 1SS133T-77 R737 1-249-424-11 CARBON 3.9K 5% 1/4W F
D707 8-719-991-33 DIODE 1SS133T-77 ! R738 1-249-401-11 CARBON 47 5% 1/4W F
R739 1-249-417-11 CARBON 1K 5% 1/4W F
< IC > R740 1-247-863-91 CARBON 22K 5% 1/4W
R741 1-247-895-91 CARBON 470K 5% 1/4W
IC701 8-759-495-96 IC uPD780205GF-040-3BA
IC702 8-749-014-66 IC NJL56H400A R742 1-249-413-11 CARBON 470 5% 1/4W F
R743 1-249-413-11 CARBON 470 5% 1/4W F
< TRANSISTOR > R744 1-249-413-11 CARBON 470 5% 1/4W F
R745 1-249-413-11 CARBON 470 5% 1/4W F
Q701 8-729-119-78 TRANSISTOR 2SC403SP-51 R746 1-249-413-11 CARBON 470 5% 1/4W F

< RESISTOR > R747 1-249-413-11 CARBON 470 5% 1/4W F

R749 1-249-413-11 CARBON 470 5% 1/4W F
R701 1-249-437-11 CARBON 47K 5% 1/4W R750 1-249-413-11 CARBON 470 5% 1/4W F
R702 1-249-429-11 CARBON 10K 5% 1/4W R751 1-249-413-11 CARBON 470 5% 1/4W F
R703 1-249-429-11 CARBON 10K 5% 1/4W R752 1-249-413-11 CARBON 470 5% 1/4W F
R704 1-249-419-11 CARBON 1.5K 5% 1/4W F
R705 1-249-419-11 CARBON 1.5K 5% 1/4W F R753 1-249-413-11 CARBON 470 5% 1/4W F
R754 1-249-413-11 CARBON 470 5% 1/4W F
R755 1-247-807-31 CARBON 100 5% 1/4W
R756 1-247-807-31 CARBON 100 5% 1/4W

— 23 —
Downloaded from www.Manualslib.com manuals search engine
 DISPLAY POWER SW TRANS TUNER

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
< VARIABLE RESISTOR > < EARTH >

RV701 1-466-336-21 ENCODER, ROTARY (TUNING/SELECT) ECP900 1-690-880-51 LEAD (WITH CONNECTOR)

< SWITCH > < TRANSFORMER >

S701 1-554-303-21 SWITCH, TACTILE (SHIFT) ! PT901 1-423-525-11 TRANSFORMER, POWER

S702 1-554-303-21 SWITCH, TACTILE (1) ************************************************************
S703 1-554-303-21 SWITCH, TACTILE (2)
S704 1-554-303-21 SWITCH, TACTILE (3) * A-4407-370-A TUNER BOARD, COMPLETE
S705 1-554-303-21 SWITCH, TACTILE (4) *********************

S706 1-554-303-21 SWITCH, TACTILE (5) 7-685-872-09 SCREW +BVTT 3 × 8 (S)

S707 1-554-303-21 SWITCH, TACTILE (6)
S708 1-554-303-21 SWITCH, TACTILE (7) < CAPACITOR >
S709 1-554-303-21 SWITCH, TACTILE (8)
S710 1-554-303-21 SWITCH, TACTILE (9) C102 1-162-306-11 CERAMIC 0.01uF 20% 16V
C103 1-126-967-11 ELECT 47uF 20% 16V
S711 1-554-303-21 SWITCH, TACTILE (0) C104 1-126-967-11 ELECT 47uF 20% 16V
S712 1-554-303-21 SWITCH, TACTILE (DIRECT) C200 1-162-306-11 CERAMIC 0.01uF 20% 16V
S713 1-554-303-21 SWITCH, TACTILE (MENU) C201 1-162-306-11 CERAMIC 0.01uF 20% 16V
S714 1-554-303-21 SWITCH, TACTILE (RETURN)
S715 1-554-303-21 SWITCH, TACTILE (ENTER) C202 1-162-306-11 CERAMIC 0.01uF 20% 16V
C203 1-162-306-11 CERAMIC 0.01uF 20% 16V
S717 1-554-303-21 SWITCH, TACTILE (DISPLAY) C204 1-162-306-11 CERAMIC 0.01uF 20% 16V
S718 1-554-303-21 SWITCH, TACTILE (PTY) C221 1-162-288-31 CERAMIC 330PF 10% 50V
S719 1-554-303-21 SWITCH, TACTILE (TA) C222 1-162-306-11 CERAMIC 0.01uF 20% 16V
S720 1-554-303-21 SWITCH, TACTILE (NEWS/INFO)
S721 1-554-303-21 SWITCH, TACTILE (AUTO-BETICAL SELECT) C223 1-162-306-11 CERAMIC 0.01uF 20% 16V
C224 1-162-306-11 CERAMIC 0.01uF 20% 16V
S722 1-554-303-21 SWITCH, TACTILE (MEMORY) C225 1-126-967-11 ELECT 47uF 20% 16V
S723 1-554-303-21 SWITCH, TACTILE (BAND) C226 1-162-306-11 CERAMIC 0.01uF 20% 16V
S724 1-554-303-21 SWITCH, TACTILE (ON/OFF) C227 1-126-956-91 ELECT 0.1uF 20% 50V
S725 1-554-303-21 SWITCH, TACTILE (ANTENNA)
S726 1-554-303-21 SWITCH, TACTILE (FM MODE) C231 1-162-306-11 CERAMIC 0.01uF 20% 16V
C232 1-162-306-11 CERAMIC 0.01uF 20% 16V
S727 1-554-303-21 SWITCH, TACTILE (CHARACTER) C235 1-162-215-31 CERAMIC 47PF 5% 50V
S728 1-554-303-21 SWITCH, TACTILE (TUNING MODE) C236 1-162-306-11 CERAMIC 0.01uF 20% 16V
C237 1-162-306-11 CERAMIC 0.01uF 20% 16V
< VIBRATOR >
C251 1-162-306-11 CERAMIC 0.01uF 20% 16V
X701 1-760-422-11 VIBRATOR, CRYSTAL (4.19MHz) C252 1-162-306-11 CERAMIC 0.01uF 20% 16V
************************************************************ C253 1-162-306-11 CERAMIC 0.01uF 20% 16V
C254 1-110-341-11 MYLAR 330PF 5% 50V
* 1-668-810-11 POWER SW BOARD C255 1-130-467-00 MYLAR 470PF 5% 50V
**************
C256 1-126-960-11 ELECT 1uF 20% 50V
< CAPACITOR > C257 1-126-967-11 ELECT 47uF 20% 16V
C258 1-162-306-11 CERAMIC 0.01uF 20% 16V
! C951 1-113-915-11 CERAMIC 0.001uF 20% 250V C259 1-126-967-11 ELECT 47uF 20% 16V
C260 1-162-306-11 CERAMIC 0.01uF 20% 16V
< SWITCH >
C261 1-162-306-11 CERAMIC 0.01uF 20% 16V
! S901 1-572-267-51 SWITCH, PUSH (AC POWER)(1 KEY) C262 1-162-306-11 CERAMIC 0.01uF 20% 16V
************************************************************ C263 1-162-306-11 CERAMIC 0.01uF 20% 16V
C264 1-126-959-11 ELECT 0.47uF 20% 50V
* 1-669-149-11 TRANS BOARD C267 1-162-306-11 CERAMIC 0.01uF 20% 16V
***********
C268 1-162-294-31 CERAMIC 0.001uF 10% 50V
< CAPACITOR > C269 1-162-306-11 CERAMIC 0.01uF 20% 16V
C270 1-162-282-31 CERAMIC 100PF 10% 50V
! C952 1-162-306-11 CERAMIC 0.01uF 20% 16V C301 1-136-161-00 FILM 0.047uF 5% 50V
C302 1-126-967-11 ELECT 47uF 20% 16V
< CONNECTOR >

CNP901 1-580-230-11 PIN, CONNECTOR (PC BOARD) 2P

CNP951 1-564-321-00 PIN, CONNECTOR 2P

The components identified by mark ! or dotted

line with mark ! are critical for safety.
Replace only with part number specified.
— 24 —
Downloaded from www.Manualslib.com manuals search engine
 TUNER

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
C303 1-136-161-00 FILM 0.047uF 5% 50V C901 1-101-004-00 CERAMIC 0.01uF 50V
C304 1-162-288-31 CERAMIC 330PF 10% 50V C902 1-101-004-00 CERAMIC 0.01uF 50V
C306 1-126-967-11 ELECT 47uF 20% 16V C903 1-126-967-11 ELECT 47uF 20% 50V
C307 1-130-468-00 MYLAR 560PF 5% 50V C904 1-126-967-11 ELECT 47uF 20% 50V
C308 1-130-468-00 MYLAR 560PF 5% 50V C905 1-126-953-11 ELECT 2200uF 20% 35V

C311 1-130-475-00 MYLAR 0.0022uF 5% 50V C906 1-126-969-11 ELECT 220uF 20% 50V
C312 1-130-475-00 MYLAR 0.0022uF 5% 50V C907 1-126-964-11 ELECT 10uF 20% 50V
C313 1-126-964-11 ELECT 10uF 20% 50V C908 1-126-964-11 ELECT 10uF 20% 50V
C314 1-126-964-11 ELECT 10uF 20% 50V C909 1-126-967-11 ELECT 47uF 20% 16V
C315 1-110-335-11 MYLAR 100PF 5% 50V C910 1-126-935-11 ELECT 470uF 20% 6.3V

C316 1-110-335-11 MYLAR 100PF 5% 50V C911 1-126-959-11 ELECT 0.47uF 20% 50V
C317 1-126-963-11 ELECT 4.7uF 20% 50V
C318 1-126-963-11 ELECT 4.7uF 20% 50V < FILTER >
C319 1-126-934-11 ELECT 220uF 20% 16V
C320 1-126-960-11 ELECT 1uF 20% 50V CF201 1-567-389-11 FILTER, CERAMIC
CF202 1-567-389-11 FILTER, CERAMIC
C321 1-126-960-11 ELECT 1uF 20% 50V CF203 1-567-389-11 FILTER, CERAMIC
C322 1-126-960-11 ELECT 1uF 20% 50V CF231 1-579-554-31 FILTER, CERAMIC
C323 1-126-959-11 ELECT 0.47uF 20% 50V CF301 1-567-250-11 OSCILLATOR, CERAMIC
C324 1-126-960-11 ELECT 1uF 20% 50V
C325 1-126-967-11 ELECT 47uF 20% 16V CF402 1-527-981-00 FILTER, CERAMIC

C351 1-130-471-00 MYLAR 0.001uF 5% 50V < JACK >

C352 1-130-471-00 MYLAR 0.001uF 5% 50V
C371 1-162-306-11 CERAMIC 0.01uF 20% 16V CNJ301 1-778-940-11 JACK 2P (LINE OUT)
C400 1-162-211-31 CERAMIC 33PF 5% 50V CNJ302 1-566-212-11 PIN, CONNECTOR 3P (EON CONTROL OUT)
C401 1-162-306-11 CERAMIC 0.01uF 20% 16V
< CONNECTOR >
C402 1-162-306-11 CERAMIC 0.01uF 20% 16V
C403 1-162-306-11 CERAMIC 0.01uF 20% 16V * CNP701 1-568-936-11 PIN, CONNECTOR 9P
C404 1-126-967-11 ELECT 47uF 20% 16V * CNP702 1-568-935-11 PIN, CONNECTOR 8P
C405 1-162-306-11 CERAMIC 0.01uF 20% 16V CNP952 1-766-267-11 PIN, CONNECTOR (PC BOARD) 5P
C406 1-162-306-11 CERAMIC 0.01uF 20% 16V
< DIODE >
C407 1-162-306-11 CERAMIC 0.01uF 20% 16V
C408 1-162-306-11 CERAMIC 0.01uF 20% 16V D221 8-719-991-33 DIODE 1SS133T-77
C409 1-162-294-31 CERAMIC 0.001uF 10% 50V D251 8-719-991-33 DIODE 1SS133T-77
C410 1-162-306-11 CERAMIC 0.01uF 20% 16V D301 8-719-991-33 DIODE 1SS133T-77
C411 1-126-967-11 ELECT 47uF 20% 16V D371 8-719-991-33 DIODE 1SS133T-77
D401 8-719-991-33 DIODE 1SS133T-77
C412 1-126-960-11 ELECT 1uF 20% 50V
C413 1-126-960-11 ELECT 1uF 20% 50V D402 8-719-991-33 DIODE 1SS133T-77
C414 1-126-960-11 ELECT 1uF 20% 50V D901 8-719-200-82 DIODE 11ES2
C415 1-126-962-11 ELECT 3.3uF 20% 50V D902 8-719-200-82 DIODE 11ES2
C418 1-162-306-11 CERAMIC 0.01uF 20% 16V D903 8-719-200-82 DIODE 11ES2
D904 8-719-200-82 DIODE 11ES2
C419 1-162-294-31 CERAMIC 0.001uF 10% 50V
C420 1-162-306-11 CERAMIC 0.01uF 20% 16V D905 8-719-110-69 DIODE RD27ES-B4
C421 1-136-161-00 FILM 0.047uF 5% 50V D906 8-719-109-97 DIODE RD6.8ES-B2
C422 1-102-508-91 CERAMIC 10PF 0.5PF 50V D907 8-719-200-82 DIODE 11ES2
C423 1-102-973-00 CERAMIC 100PF 5% 50V D908 8-719-991-33 DIODE 1SS133T-77

C424 1-162-306-11 CERAMIC 0.01uF 20% 16V < FRONTEND >

C425 1-126-964-11 ELECT 10uF 20% 50V
C427 1-130-471-00 MYLAR 0.001uF 5% 50V FE101 1-233-524-11 ENCAPSULATED COMPONENT
C428 1-162-211-31 CERAMIC 33PF 5% 50V FE401 1-233-525-11 ENCAPSULATED COMPONENT
C429 1-162-306-11 CERAMIC 0.01uF 20% 16V
< IC >
C430 1-162-294-31 CERAMIC 0.001uF 10% 50V
C801 1-126-961-11 ELECT 2.2uF 20% 50V IC221 8-759-812-35 IC LA1235
C803 1-162-306-11 CERAMIC 0.01uF 20% 16V IC251 8-759-812-35 IC LA1235
C804 1-162-291-31 CERAMIC 560PF 10% 50V IC301 8-759-801-80 IC LA3401
C805 1-126-967-11 ELECT 47uF 20% 16V IC302 8-759-634-51 IC M5218AP
IC401 8-759-812-45 IC LA1245
C806 1-162-306-11 CERAMIC 0.01uF 20% 16V
C807 1-102-852-91 CERAMIC 47PF 5% 50V IC801 8-759-450-86 IC BU1922
C808 1-102-527-11 CERAMIC 82PF 5% 50V IC901 8-759-820-09 IC LA5667
C809 1-162-306-11 CERAMIC 0.01uF 20% 16V
C810 1-162-306-11 CERAMIC 0.01uF 20% 16V

— 25 —
Downloaded from www.Manualslib.com manuals search engine
 TUNER

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
< IFT > R205 1-249-411-11 CARBON 330 5% 1/4W
R206 1-249-413-11 CARBON 470 5% 1/4W F
IFT252 1-404-845-11 COIL, DISCRI (PRIMARY) R207 1-249-411-11 CARBON 330 5% 1/4W
IFT253 1-404-846-11 COIL, DISCRI (SECONDARY) R208 1-247-863-91 CARBON 22K 5% 1/4W
IFT401 1-404-713-11 TRANSFORMER, IF R209 1-249-411-11 CARBON 330 5% 1/4W

< COIL > R210 1-249-431-11 CARBON 15K 5% 1/4W

R211 1-249-411-11 CARBON 330 5% 1/4W
L201 1-410-521-11 INDUCTOR 100uH R212 1-249-411-11 CARBON 330 5% 1/4W
L351 1-410-509-11 INDUCTOR 10uH R213 1-247-863-91 CARBON 22K 5% 1/4W
L352 1-410-509-11 INDUCTOR 10uH R214 1-249-441-11 CARBON 100K 5% 1/4W
L400 1-414-142-11 INDUCTOR 1uH
L401 1-410-521-11 INDUCTOR 100uH R221 1-249-413-11 CARBON 470 5% 1/4W F
! R222 1-249-405-11 CARBON 100 5% 1/4W F
< FILTER > R223 1-247-883-00 CARBON 150K 5% 1/4W
R231 1-249-411-11 CARBON 330 5% 1/4W
LPF301 1-235-164-00 FILTER, LOW PASS R232 1-249-431-11 CARBON 15K 5% 1/4W
LPF302 1-235-164-00 FILTER, LOW PASS
R233 1-249-411-11 CARBON 330 5% 1/4W
< TRANSISTOR > R234 1-249-395-11 CARBON 15 5% 1/4W F
R235 1-247-863-91 CARBON 22K 5% 1/4W
Q200 8-729-216-13 TRANSISTOR 2SK161-GR R238 1-249-429-11 CARBON 10K 5% 1/4W
Q201 8-729-230-99 TRANSISTOR 2SC2669-OY R239 1-249-429-11 CARBON 10K 5% 1/4W
Q202 8-729-230-99 TRANSISTOR 2SC2669-OY
Q204 8-729-230-99 TRANSISTOR 2SC2669-OY R240 1-249-431-11 CARBON 15K 5% 1/4W
Q205 8-729-230-99 TRANSISTOR 2SC2669-OY R241 1-249-429-11 CARBON 10K 5% 1/4W
R242 1-249-429-11 CARBON 10K 5% 1/4W
Q231 8-729-030-02 TRANSISTOR DTC144ESA R243 1-247-807-31 CARBON 100 5% 1/4W
Q232 8-729-030-02 TRANSISTOR DTC144ESA R244 1-249-405-11 CARBON 100 5% 1/4W F
Q233 8-729-030-02 TRANSISTOR DTC144ESA
Q234 8-729-119-78 TRANSISTOR 2SC403SP-51 R245 1-249-405-11 CARBON 100 5% 1/4W F
Q235 8-729-119-78 TRANSISTOR 2SC403SP-51 R246 1-249-405-11 CARBON 100 5% 1/4W F
R251 1-249-411-11 CARBON 330 5% 1/4W
Q236 8-729-230-99 TRANSISTOR 2SC2669-OY R252 1-249-437-11 CARBON 47K 5% 1/4W
Q237 8-729-230-99 TRANSISTOR 2SC2669-OY R253 1-249-439-11 CARBON 68K 5% 1/4W
Q251 8-729-230-99 TRANSISTOR 2SC2669-OY
Q301 8-729-922-37 TRANSISTOR 2SD2144S R254 1-249-421-11 CARBON 2.2K 5% 1/4W F
Q302 8-729-922-37 TRANSISTOR 2SD2144S R255 1-249-421-11 CARBON 2.2K 5% 1/4W F
R256 1-249-432-11 CARBON 18K 5% 1/4W
Q303 8-729-922-37 TRANSISTOR 2SD2144S R257 1-249-424-11 CARBON 3.9K 5% 1/4W F
Q304 8-729-922-37 TRANSISTOR 2SD2144S R258 1-249-422-11 CARBON 2.7K 5% 1/4W F
Q401 8-729-230-99 TRANSISTOR 2SC2669-OY
Q402 8-729-231-20 TRANSISTOR 2SK161-YGR ! R259 1-249-405-11 CARBON 100 5% 1/4W F
Q403 8-729-922-37 TRANSISTOR 2SD2144S R260 1-249-439-11 CARBON 68K 5% 1/4W
R261 1-249-437-11 CARBON 47K 5% 1/4W
Q404 8-729-922-37 TRANSISTOR 2SD2144S R262 1-249-441-11 CARBON 100K 5% 1/4W
Q405 8-729-922-37 TRANSISTOR 2SD2144S R269 1-249-441-11 CARBON 100K 5% 1/4W
Q521 8-729-030-02 TRANSISTOR DTC144ESA
Q522 8-729-026-41 TRANSISTOR 2SA933AS-QRT R270 1-247-883-00 CARBON 150K 5% 1/4W
Q523 8-729-119-78 TRANSISTOR 2SC403SP-51 R271 1-249-417-11 CARBON 1K 5% 1/4W F
R272 1-249-417-11 CARBON 1K 5% 1/4W F
Q801 8-729-119-78 TRANSISTOR 2SC403SP-51 R273 1-249-422-11 CARBON 2.7K 5% 1/4W F
Q901 8-729-029-56 TRANSISTOR DTA144ESA ! R274 1-249-393-11 CARBON 10 5% 1/4W F

< RESISTOR > R275 1-247-903-00 CARBON 1M 5% 1/4W

R300 1-249-421-11 CARBON 2.2K 5% 1/4W F
R101 1-249-417-11 CARBON 1K 5% 1/4W F R301 1-247-883-00 CARBON 150K 5% 1/4W
! R102 1-249-405-11 CARBON 100 5% 1/4W F R302 1-247-883-00 CARBON 150K 5% 1/4W
! R103 1-249-393-11 CARBON 10 5% 1/4W F R303 1-247-878-00 CARBON 91K 5% 1/4W
R104 1-247-863-91 CARBON 22K 5% 1/4W
R105 1-249-437-11 CARBON 47K 5% 1/4W R304 1-247-878-00 CARBON 91K 5% 1/4W
R305 1-249-421-11 CARBON 2.2K 5% 1/4W F
R200 1-249-408-11 CARBON 180 5% 1/4W F R306 1-249-421-11 CARBON 2.2K 5% 1/4W F
R201 1-249-407-11 CARBON 150 5% 1/4W F R307 1-249-426-11 CARBON 5.6K 5% 1/4W
R202 1-249-411-11 CARBON 330 5% 1/4W R308 1-249-426-11 CARBON 5.6K 5% 1/4W
R203 1-249-411-11 CARBON 330 5% 1/4W
R204 1-249-431-11 CARBON 15K 5% 1/4W

The components identified by mark ! or dotted

line with mark ! are critical for safety.
Replace only with part number specified.
— 26 —
Downloaded from www.Manualslib.com manuals search engine
 TUNER

Ref. No. Part No. Description Remarks Ref. No. Part No. Description Remarks
R309 1-249-426-11 CARBON 5.6K 5% 1/4W R905 1-249-437-11 CARBON 47K 5% 1/4W
R310 1-249-426-11 CARBON 5.6K 5% 1/4W R906 1-249-437-11 CARBON 47K 5% 1/4W
! R311 1-249-405-11 CARBON 100 5% 1/4W F
! R312 1-249-405-11 CARBON 100 5% 1/4W F < VARIABLE RESISTOR >
R313 1-249-427-11 CARBON 6.8K 5% 1/4W F
RV221 1-241-765-11 RES, ADJ, CARBON 22K
R314 1-249-427-11 CARBON 6.8K 5% 1/4W F RV231 1-241-763-11 RES, ADJ, CARBON 4.7K
R315 1-247-815-91 CARBON 220 5% 1/4W RV251 1-241-764-11 RES, ADJ, CARBON 10K
R316 1-247-815-91 CARBON 220 5% 1/4W RV301 1-241-767-21 RES, ADJ, CARBON 100K
R317 1-249-417-11 CARBON 1K 5% 1/4W F RV402 1-241-764-11 RES, ADJ, CARBON 10K
R318 1-249-417-11 CARBON 1K 5% 1/4W F
< TRANSFORMER >
R319 1-249-437-11 CARBON 47K 5% 1/4W
R320 1-249-437-11 CARBON 47K 5% 1/4W T251 1-235-126-00 ENCAPSULATED COMPONENT
R321 1-249-441-11 CARBON 100K 5% 1/4W
R324 1-249-426-11 CARBON 5.6K 5% 1/4W < TERMINAL >
! R325 1-249-405-11 CARBON 100 5% 1/4W F
TM401 1-537-897-11 TERMINAL BOARD,PUSH(ANTENNA)2P
! R326 1-249-405-11 CARBON 100 5% 1/4W F
R331 1-247-815-91 CARBON 220 5% 1/4W < TEST PIN >
R332 1-247-815-91 CARBON 220 5% 1/4W
R333 1-249-417-11 CARBON 1K 5% 1/4W F TP251 1-766-275-11 PIN, CONNECTOR (PC BOARD) 2P
R334 1-249-417-11 CARBON 1K 5% 1/4W F
< VIBRATOR >
R351 1-249-437-11 CARBON 47K 5% 1/4W
R352 1-249-437-11 CARBON 47K 5% 1/4W X801 1-579-900-21 VIBRATOR, CRYSTAL (4.332MHz)
R363 1-249-381-11 CARBON 1 5% 1/4W F ************************************************************
R371 1-249-393-11 CARBON 10 5% 1/4W F
R401 1-249-421-11 CARBON 2.2K 5% 1/4W F MISCELLANEOUS
*************
! R402 1-249-409-11 CARBON 220 5% 1/4W F
R404 1-249-413-11 CARBON 470 5% 1/4W F !8 1-575-651-21 CORD, POWER
R405 1-247-807-31 CARBON 100 5% 1/4W !9 1-770-019-11 ADAPTOR, CONVERSION PLUG 3P (UK)
R406 1-247-807-31 CARBON 100 5% 1/4W FL701 1-157-117-21 FLUORESCENT INDICATOR TUBE
R408 1-249-429-11 CARBON 10K 5% 1/4W ************************************************************

R409 1-249-429-11 CARBON 10K 5% 1/4W ACCESSORIES & PACKING MATERIALS

R410 1-249-430-11 CARBON 12K 5% 1/4W *******************************
R411 1-249-417-11 CARBON 1K 5% 1/4W F
! R412 1-249-407-11 CARBON 150 5% 1/4W F 1-501-594-11 ANTENNA (FM)
R413 1-249-429-11 CARBON 10K 5% 1/4W 1-501-721-11 ANTENNA (LOOP)
1-558-271-11 CORD, CONNECTION
R414 1-249-441-11 CARBON 100K 5% 1/4W 1-765-383-11 CORD (WITH CONNECTOR)
R415 1-247-883-00 CARBON 150K 5% 1/4W 3-861-974-11 MANUAL, INSTRUCTION
R416 1-249-417-11 CARBON 1K 5% 1/4W F (ENGLISH, FRENCH, SPANISH, PORTUGUESE)
R419 1-249-422-11 CARBON 2.7K 5% 1/4W F
R420 1-249-441-11 CARBON 100K 5% 1/4W 3-861-974-21 MANUAL, INSTRUCTION(AEP)
(GERMAN, DUTCH, SWEDISH, ITALIAN)
R421 1-249-417-11 CARBON 1K 5% 1/4W F 3-861-974-31 MANUAL, INSTRUCTION(AEP)
R422 1-249-418-11 CARBON 1.2K 5% 1/4W F (DANISH, FINNISH)
R423 1-249-418-11 CARBON 1.2K 5% 1/4W F ************************************************************
R424 1-249-421-11 CARBON 2.2K 5% 1/4W F
R425 1-249-420-11 CARBON 1.8K 5% 1/4W F *************
HARDWARE LIST
R426 1-249-421-11 CARBON 2.2K 5% 1/4W F *************
! R429 1-249-393-11 CARBON 10 5% 1/4W F
R430 1-249-441-11 CARBON 100K 5% 1/4W #1 7-685-646-79 SCREW +BVTP 3 × 8 TYPE2 IT-3
R431 1-249-429-11 CARBON 10K 5% 1/4W #2 7-685-885-09 SCREW +BVTT 4 × 16 (S)
R521 1-247-843-11 CARBON 3.3K 5% 1/4W #3 7-685-234-19 SCREW +KTP 2.6 × 8 TYPE2NON-SLIT
#4 7-685-534-19 SCREW +BTP 2.6 × 8 TYPE2 N-S
R522 1-247-863-91 CARBON 22K 5% 1/4W
! R801 1-249-401-11 CARBON 47 5% 1/4W F
R802 1-249-421-11 CARBON 2.2K 5% 1/4W F
R803 1-249-429-11 CARBON 10K 5% 1/4W
! R804 1-249-405-11 CARBON 100 5% 1/4W F

R808 1-247-815-91 CARBON 220 5% 1/4W

R809 1-247-807-31 CARBON 100 5% 1/4W
! R902 1-247-752-11 CARBON 1K 5% 1/2W F
R903 1-249-441-11 CARBON 100K 5% 1/4W
R904 1-249-437-11 CARBON 47K 5% 1/4W
The components identified by mark ! or dotted
line with mark ! are critical for safety.
Replace only with part number specified.
— 27 —
Downloaded from www.Manualslib.com manuals search engine
 ST-SB920

Sony Corporation 98F167549-1

Printed in Hungary ©1998.6
9-922-881-11 Home A&V Products Company
Published by Quality Assurance Dept.
— 28 — (Shibaura)
Downloaded from www.Manualslib.com manuals search engine