Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 2K views

    Wavelength by Grating

    Uploaded by

    prateekjain01
    The document describes an experiment to determine the wavelength of spectral lines from mercury light using a diffraction grating. Key steps include: 1) Adjusting the spectrometer and leveling the prism table. 2) Setting up the grating perpendicular to the collimator axis using a series of rotations. 3) Measuring the angle of diffraction for different spectral lines and calculating their wavelengths using the grating equation.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as DOC, PDF, TXT or read online from Scribd

    Wavelength by Grating

    Uploaded by

    prateekjain01
    2K views7 pages
    The document describes an experiment to determine the wavelength of spectral lines from mercury light using a diffraction grating. Key steps include: 1) Adjusting the spectrometer and leveling the prism table. 2) Setting up the grating perpendicular to the collimator axis using a series of rotations. 3) Measuring the angle of diffraction for different spectral lines and calculating their wavelengths using the grating equation.

    Copyright

    © Attribution Non-Commercial (BY-NC)

    Available Formats

    DOC, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    The document describes an experiment to determine the wavelength of spectral lines from mercury light using a diffraction grating. Key steps include: 1) Adjusting the spectrometer and leveling the prism table. 2) Setting up the grating perpendicular to the collimator axis using a series of rotations. 3) Measuring the angle of diffraction for different spectral lines and calculating their wavelengths using the grating equation.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as DOC, PDF, TXT or read online from Scribd
    Download as doc, pdf, or txt
    2K views7 pages

    Wavelength by Grating

    Uploaded by

    prateekjain01
    The document describes an experiment to determine the wavelength of spectral lines from mercury light using a diffraction grating. Key steps include: 1) Adjusting the spectrometer and leveling the prism table. 2) Setting up the grating perpendicular to the collimator axis using a series of rotations. 3) Measuring the angle of diffraction for different spectral lines and calculating their wavelengths using the grating equation.

    Copyright:

    Attribution Non-Commercial (BY-NC)
    Download as DOC, PDF, TXT or read online from Scribd
    Download as doc, pdf, or txt
    of 7

    -1-

    EXPERIMENT NO. :-5


    Diffraction Grating
    OBJECT: To determine the wavelength of prominent spectral lines of mercury light by a plane Transmission grating, using normal incidence method. APPARATUS: Mercury lamp. Spectrometer, diffraction grating and a reading lens, eye-piece, prism FORMULA USED: The wavelength of any spectral line can be obtained from the formula.
    ( a + b) sin = n

    or,

    ( a + b) Sin n

    Where, a + b = Grating element

    = Angle of diffraction
    n = Order of principal maxima A) Adjustment of Spectrometer The following adjustments should be done: I) The optical axes of telescope and collimator should be perpendicular to the axis of rotation of the turn table and should meet at the same point. This adjustment is done by the manufacturer. II) Adjustment of the turn table: 1. The prism table is leveled with the help of three screws beneath the prism table. A spirit level is placed along the line joining the screws and the two screws are moved till the air bubble moves in the middle. Now place the spirit level along a line perpendicular to the previous line and adjust the third screw such that again the air bubble appears in the middle. Here one thing should be remembered that first two screws should not be touched this time. The prism table is now leveled.

    2. The second method which is generally used is optical leveling of the prism table. In this
    method the prism is placed on the prism table with its refracting edge at the centre of the prism table and one of its polished surface perpendicular to the line joining the two leveling screws P and Q as shown in fig 1(a).

    -2-

    fig 1(a) Now rotate the prism table in such a way that refracting edges AB and AC face towards the collimator and light falling on the prism is usually reflected from both the sides as in fig 1(b). The telescope is moved to the one side to receive the light reflected from the face AB and the leveling screws P and Q are adjusted to obtain image in the central field of view of the telescope. Again the telescope is moved to the other side to receive light reflected from face AC and remaining third screw R is adjusted till image becomes in central field of view of this telescope. The prism table is now leveled III) Schusters method for focusing the telescope and collimator: a) First of all prism is placed on the prism table and then adjusted for minimum deviation position. The spectrum is now seen through the telescope. (Note: The turn table is rotated such that the light from the collimator may fall on the face AB and emerge through the face AC so that the spectrum is visible in the field of view of the telescope. Now, if the prism table is slightly rotated in the either direction till the refracted image of slit (spectrum) is obtained. The spectrum during the rotation of the table moves in one direction and it begins to retrace the path from a certain position when the rotation is still continued in the same direction. At this position, the rays suffer minimum deviation.) b) The prism table is rotated slightly away from this position towards the collimator and spectrum is viewed focusing collimator on the spectrum. c) Again rotate the prism table on the other side of minimum deviation position i.e. towards the telescope and focus telescope for best image of the spectrum. d) The process of focusing the collimator and telescope is continued till the slight rotation of prism table does not make the image to go out of focus. This means that both the collimator and the telescope are now individually set for parallel rays.

    IV) Grating should be normal to the axis of collimator:

    -31. Collimator and telescope are arranged in a line and the image of the grating is
    focused on the vertical cross-wire.

    2. The telescope is then rotated through 900 from this position. 3. The prism table is now rotated till the image of the slit, formed by reflection from
    the grating is thrown on the cross-wire.

    4. The turn table is then rotated through 450 or 1350 from this position. The plane of
    the grating thus be comes normal to the collimator axis. (Figures 1-4) After doing all the adjustments view the image of slit through telescope. Now remove the grating keeping eyes on eye-piece. Image of the slit should remain in the same place and should not shift in position. PROCEDURE:

    A. READINGS FOR THE ANGLE OF DIFFRACTION ARE


    TAKEN AS FOLLOWS:

    1) The telescope is rotated on one side (say left) of the direct image till red line of the first order spectrum comes on the cross wire (fig5). The readings of both the verniers are recorded. Similarly, readings of both the verniers are recorded for other spectral lines (say yellow and violet). 2) Now rotate the telescope on the other side of the direct image and repeat the same procedure as above. 3) Find out the difference in readings of the same kind of verniers for each spectral line and calculate angle of diffraction.
    OBSERVATIONS: (1) Observation for adjustment of the grating : Least Count of the spectrometer = . = degrees

    (2) Observations for the grating element: Number of lines per inch on the grating = .. Grating element ( a + b) =
    num ber 2.54 cm of lines per inch

    -4= ............................cm (3)Observations for angle of diffraction: Color of Order of Spectrum Green 1st Yellow Red Spectru m Reading for the Spectrum on L.H.S. R.H.S. V1 (a) V2 (b) V1(c) V2 (d)
    (in degrees) (in degrees) (in degrees) (in degrees)

    1st a-c (deg)

    Value of 2 Vernier 2nd Mean b-d (deg) (in degrees)

    Value of
    (in degrees)

    CALCULATIONS:

    ( a + b) Sin n

    RESULT: Violet line

    = --------------- = ------------ = ------------

    Yellow Line y Red Line

    PRECAUTIONS: 1. The grating should not be touched with hand or rubbed. It should always be held by means of fingers kept on the opposite edges of the grating. 2. Grating should be perfectly normal to the axis of the collimator. 3. The turn table must be leveled optically. 4. While recording observations the telescope should be rotated in the same direction in order to avoid backlash error. 5. The slit should be as narrow as possible. 6. All the preliminary adjustments of the spectrometer must be made before starting the experiment. 7. While taking observations the turn table must remain clamped. 8. Both verniers should be read.

    -5-

    Sources of error: 1. The spectrometer is not properly adjusted. 2. Error may be due to parallax.

    3. If the reading is not taken overhead the spectrometer.


    4. Reading may not be taken taking care of precautions. Maximum probable error:

    ( a + b) Sin n

    Taking log of both sides and then differentiating we get:


    d d = tan

    d = least count of circular scale of spectrometer in terms of

    = any one value of during reading

    -6-

    ADJUSTMENT OF GRATING FOR NORMAL INCIDENCE (STEP 4-5)

    Step 1

    Telescope

    Collimator

    Fig1 Step 2 ----------------------------------Collimator

    Telescope

    Fig 2 Step 3

    Collimator

    Telescope

    -7-

    Fig 3

    Step 4

    Telescope

    Collimator

    Fig 4

    Step 5 _ _ _ _ _ _ _ _ _ _ _ _ _ _ __

    Collimator

    Telescope

    Fig 5

    Collimeter

    You might also like