3102309-En r001 Est4 User Guide

EST4 User Guide
P/N 3102309-EN • REV 001 • ISS 18JUL19

Copyright © 2019 United Technologies Corporation
All rights reserved.
This document may not be copied in whole or in part or otherwise reproduced without
prior written consent from United Technologies Corporation, except where specifically
permitted under US and international copyright law.
Trademarks and patents The Edwards name and logo are trademarks of United Technologies Corporation.
Other trade names used in this document may be trademarks or registered trademarks
of the manufacturers or vendors of the respective products.
Contact information For contact information, see www.edwardsfiresafety.com.
Content
Important information iii

Intended audience v
Life safety system limitations v
Chapter 1 Introduction 1
System overview 2
EST4 LCD user interface 2
System operation 8
User fire privilege levels 10
Using the touch screen 11
Chapter 2 Basic operating instructions 17

Silencing the operator alert signal 18
Silencing alarm signals 18
Acknowledging events 19
Displaying event lists 19
Viewing event details 20
Changing the LCD screen to an alternate language 21
Viewing the alarm count 22
Checking system device statuses 22
Performing a lamp test 22
Activating an alarm signals drill 23
Resetting the life safety system 23
Finding detectors needing maintenance 24
Viewing history reports 24
Finding firmware and system information 25
Obtaining an access code for a system programmer 26
Requesting, granting, or denying control 27
Making voice and emergency announcements 28
Chapter 3 Advanced operating instructions 35

Changing web service access 36
Freezing the events history 36
Changing the smoke detector alarm sensitivity threshold 36
Setting the system date and time 37
Disabling and enabling devices 37
Disabling and enabling local rail modules 38
Disabling and enabling logic groups 39
Disabling and enabling time controls 39
Changing output states 40
Control-Display modules 40
Chapter 4 Preventive maintenance and testing 43

Introduction 44
Service provider information 44
Visual inspection schedule 45
Troubleshooting 46
Appendix A System addressing 47

Address format 48
Module addresses 48
P/N 3102309-EN • REV 001 • ISS 18JUL19 i

LRM device addresses 51
Control-display device addresses 51
Glossary 57
Index 59
ii P/N 3102309-EN • REV 001 • ISS 18JUL19

Important information
Regulatory information
This product has been designed to meet the requirements of NFPA 72 National Fire Alarm Signaling Code,
UL 864 Standard for Control Units and Accessories for Fire Alarm Systems, and CAN/ULC-S527 Standard for
Control Units for Fire Alarm Systems.
Limitation of liability
To the maximum extent permitted by applicable law, in no event will United Technologies Corporation be liable for
any lost profits or business opportunities, loss of use, business interruption, loss of data, or any other indirect,
special, incidental, or consequential damages under any theory of liability, whether based in contract, tort,
negligence, product liability, or otherwise. Because some jurisdictions do not allow the exclusion or limitation of
liability for consequential or incidental damages the preceding limitation may not apply to you. In any event the
total liability of United Technologies Corporation shall not exceed the purchase price of the product. The foregoing
limitation will apply to the maximum extent permitted by applicable law, regardless of whether United
Technologies Corporation has been advised of the possibility of such damages and regardless of whether any
remedy fails of its essential purpose.
Installation in accordance with this manual, applicable codes, and the instructions of the authority having
jurisdiction is mandatory.
While every precaution has been taken during the preparation of this manual to ensure the accuracy of its
contents, United Technologies Corporation assumes no responsibility for errors or omissions.
Advisory messages
Advisory messages alert you to conditions or practices that can cause unwanted results. The advisory messages
used in this document are shown and described below.
WARNING: Warning messages advise you of hazards that could result in injury or loss of life. They tell you which
actions to take or to avoid in order to prevent the injury or loss of life.
Caution: Caution messages advise you of possible equipment damage. They tell you which actions to take or to
avoid in order to prevent the damage.
Note: Note messages advise you of the possible loss of time or effort. They describe how to avoid the loss. Notes
are also used to point out important information that you should read.
EST4 FCC compliance

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part
15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference
when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate
radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause
harmful interference in which case the user will be required to correct the interference at his own expense.
P/N 3102309-EN • REV 001 • ISS 18JUL19 iii

3-MODCOM(P) FCC compliance
Cautions
• To ensure proper operation, this dialer must be installed according to the enclosed installation instructions. To
verify that the dialer is operating properly and can successfully report an alarm, it must be tested immediately
after installation, and periodically thereafter, according to the enclosed test instructions.
• In order for the dialer to be able to seize the phone line to report an alarm or other event when other customer
equipment (telephone, answering system, computer modem, etc.) connected to the same line is in use, the
dialer must be connected to a properly installed RJ-31X jack. The RJ-31X jack must be connected in series
with, and ahead of, all other equipment attached to the same phone line. Series installation of an RJ-31X jack
is depicted in the wiring diagram. If you have any questions concerning these instructions, you should consult
your telephone company or a qualified installer.
Testing
When programming emergency numbers or making test calls to emergency numbers, remain on the line and
briefly explain to the dispatcher the reason for the call. Perform programming and testing activities in the off-peak
hours, such as early morning or late evenings.
Compliance
• For equipment approved before July 23, 2001: This dialer complies with Part 68 of the FCC rules. A label
attached to the dialer contains, among other information, the FCC registration number and ringer equivalence
number (REN) for this equipment. If requested, this information must be provided to the telephone company.
• For equipment approved after July 23, 2001: This dialer complies with Part 68 of the FCC rules and the
requirements adopted by the Administrative Council for Terminal Attachments (ACTA). A label attached to the
dialer contains, among other information, a product identifier in the format US:AAAEQ##TXXXX. If requested,
this information must be provided to the telephone company.
• The plug and jack used to connect the dialer to the premises wiring and telephone network must comply with
the applicable FCC Part 68 rules and requirements adopted by ACTA. The dialer must be connected to a
compliant RJ-31X or RJ-38X jack using a compliant cord. If a modular telephone cord is supplied with the
dialer, it is designed to meet these requirements. See installation instructions for details.
• A ringer equivalence number is used to determine how many devices you can connect to a telephone line. If
the total REN value for all devices connected on a telephone line exceeds that allowed by the telephone
company, the devices may not ring on an incoming call. In most (but not all) areas the total REN value should
not exceed 5.0. To be certain of the total REN value allowed on a telephone line, contact the local telephone
company.
For products approved after July 23, 2001, the REN is part of the product identifier in the format
US:AAAEQ##TXXXX. The digits ## represent the REN without a decimal point. Example: 03 is an REN of
0.3. For earlier products the REN is listed separately.
• If the dialer is harming the telephone network, the telephone company will notify you in advance that
temporary discontinuance of service may be required. If advance notice isn’t practical, the telephone
company will notify you as soon as possible. You will also be advised of your right to file a complaint with the
FCC, if you believe it is necessary.
• The telephone company may make changes to its facilities, equipment, operations, or procedures that could
affect the operation of the dialer. If this happens, the telephone company will provide advance notice in order
for you to make necessary modifications to maintain uninterrupted service.
• If you are experiencing problems with the dialer, contact the manufacturer for repair or warranty information. If
the dialer is harming the telephone network, the telephone company may request that you disconnect the
dialer until the problem is resolved.
• The dialer contains no user serviceable parts. In case of defects, return the dialer for repair.
iv P/N 3102309-EN • REV 001 • ISS 18JUL19

• You may not connect the dialer to a public coin phone or a party line service provided by the telephone
company.
3-MODCOM(P) Industry Canada information

Note: The Industry Canada label identifies certified equipment. This certification means that the equipment meets
certain telecommunications network protective, operational, and safety requirements. Industry Canada does not
guarantee the equipment will operate to the user’s satisfaction.
Before installing this equipment, users should ensure that it is permissible to be connected to the facilities of the
local telecommunications company. The equipment must also be installed using an acceptable method of
connection. The customer should be aware that compliance with the above conditions may not prevent
degradation of service in some situations.
Repairs to certified equipment should be made by an authorized Canadian maintenance facility designated by the
supplier. Any repairs or alterations made by the user to this equipment, or equipment malfunctions, may give the
telecommunications company cause to request the user disconnect the equipment.
Caution: Users should not attempt to make connections themselves, but should contact the appropriate electric
inspection authority, or electrician, as appropriate
Users should ensure for their own protection that the electrical ground connections of the power utility, telephone
lines, and internal metallic water pipe system, if present, are connected together. This precaution may be
particularly important in rural areas.
Note: The Load Number (LN) assigned to each terminal device denotes the percentage of the total load to be
connected to a telephone loop which is used by the device, to prevent overloading. The termination on a loop may
consist of any combination of devices subject only to the requirements that the sum of the Load Numbers of all
the devices does not exceed 100.
Intended audience
The intent of this document is to provide the EST4 life safety system owner with control unit operating
instructions. You may assume that your site-specific software has been installed and that the final overall system
testing has been completed prior to you using this guide. The extent of your use with control unit buttons,
indicators, and command features is dependent upon your fire privilege level access.
Life safety system limitations

The purpose of an automatic fire alarm system is to provide early detection and warning of a developing fire.
There are a number of uncontrollable factors that can prevent or severely limit the ability of an automatic fire
alarm system to provide adequate protection. As such, an automatic fire alarm system cannot guarantee against
loss of life or loss of property.
Two main causes of system failures are improper installation and poor maintenance. The best way to minimize
these types of system failures is to have only trained fire alarm system professionals design, install, test, and
maintain your fire alarm system in accordance with national and local fire codes.
Fire alarm systems will not operate without electrical power. As fires frequently cause power interruption, we
suggest that you discuss ways to safeguard the electrical system with your local fire protection specialist.
In the event your EST4 control unit needs servicing, please contact your system service provider as soon as
possible. Refer to “Service provider information” on page 44 for their name and contact information.
P/N 3102309-EN • REV 001 • ISS 18JUL19 v

vi P/N 3102309-EN • REV 001 • ISS 18JUL19
Chapter 1
Introduction
Summary
This chapter provides information about your EST4 control unit to give you a basic understanding of its operation.
Content
System overview 2
EST4 LCD user interface 2
Command controls and indicators 2
LCD screen indications 5
LCD screen operator controls 7
System operation 8
Event indicator queues 8
Event message lists 9
User fire privilege levels 10
Using the touch screen 10
List bar 11
Action bar 12
Command bar 13
P/N 3102309-EN • REV 001 • ISS 18JUL19 1

Chapter 1: Introduction
System overview
The EST4 life safety system can operate as a stand-alone control unit or as part of an EST4 life safety network.
The EST4 user interface includes indicators and operator controls that allow you to respond quickly in emergency
situations. The user interface gives you the ability to view message details and system reports, and to enable and
disable devices and groups. With the correct fire privilege PIN, you can activate and restore sensitivity settings,
test system devices, and perform other tasks.
EST4 LCD user interface

An EST4 system uses LCD display modules to provide the user interface for the fire alarm control unit.
• The 4-LCD and 4-3LCD modules are main LCD display modules that include operator command controls,
LED indicators, and an LCD screen.
• The 4-LCDAUDTEL Audio and Firefighter Telephone Control LCD Display Module includes an operator LCD
screen.
Figure 1: LCD user interface (4-LCD shown)
(1) (2) (3) (4)
ALARM TROUBLE CPU FAIL POWER ON
(5)
PANEL SILENCE (6)

FIRE DRILL (7)
ALARM SILENCE (8)
RESET (9)
Command controls and indicators

The 4-LCD and 4-3LCD user interface command controls and indicators are shown in Figure 1 above. See
Table 1 on page 3 for a description of each control and indicator.
2 P/N 3102309-EN • REV 001 • ISS 18JUL19

Table 1: User interface command controls and indicators descriptions

No. Control/Indicator Description
1 Alarm LED The LED serves as a common alarm event indicator.
2 Trouble LED The LED serves as a common trouble event indicator.
3 CPU Fail LED The LED indicates that the CPU has detected a processor failure. Processor failures
must be reset manually using the Reset button. A steady LED indicates that the CPU Fail
pseudo point is active. An off LED indicates that CPU communications has been
restored.
4 Power On LED The LED indicates the power status for the control unit. The indicator is set by the
selected market.
Power Always On: A steady LED indicates that either primary power or standby power
are present. An off LED indicates that both primary power and standby power are
missing.
Power Follows AC: A steady LED indicates that primary power is present and off when
primary power is missing. An off LED indicates that standby power is present or is
missing.
Power Only If Available AC and Battery: A steady LED indicates that both primary
power and standby power are present. An off LED indicates that either primary power or
standby power are missing.
5 LCD screen The LCD screen display provides information relevant to the current condition of the
control unit, as well as operator controls. See “LCD screen indications” on page 5 for
details on the LCD screen.
6 Panel Silence button and This configurable button is programmed by default as Panel Silence.
LED (button one default
label and setting) The button can be configured as:
Panel Silence: For local systems, pressing the Panel Silence button turns the operator
alert signal off and acknowledges all events have been reviewed.
For proprietary systems, the Panel Silence button is not operational. The operator alert
signal only silences after each event has been individually acknowledged in the order
displayed.
The Panel Silence LED turns on as white while the button is pressed. When the button is
released, the LED is on steady as yellow, indicating the control unit is in an off-normal
condition and the control unit has been placed in Panel Silence mode, and turns off when
the system returns to normal.
Drill: Pressing the Fire Drill button activates the system drill response. Pressing the
button a second time cancels the drill response.
The LED turns on as white while the button is pressed. When the button is released, the
LED is on steady as yellow, indicating that the command function is active, and turns off
when the function ends.
Alternate Alarm Sensitivity: Smoke detectors can operate using two levels of
sensitivity: primary and alternate. Pressing the Alternate Sensitivity button switches
Signature detectors to their alternate operating settings. Pressing the button a second
time switches them back to primary sensitivity levels.
Acknowledge: Pressing the Acknowledge button acknowledges events.
For proprietary systems, pressing the Acknowledge button acknowledges an event and
turns the operator alert signal off when each event has been individually acknowledged in
the order displayed.
when the system returns to normal.
P/N 3102309-EN • REV 001 • ISS 18JUL19 3


Lamp Test: Pressing the Lamp Test button temporarily turns on all visual indicators on
the local control unit and the LCD screen cycles through colors to reveal any dead pixels.
Note: If the local control unit is part of a command center, the lamp test is also executed
on all nodes within the command center.
System Function 1, System Function 2, System Function 3, or System Function 4:
Pressing the System Function button activates the response programmed for function.
None: No action assigned.
7 Fire Drill button and LED This configurable button is programmed by default as Drill (Fire Drill).
(button two default label
The button can be configured in the 4-CU as:
and setting)
Drill: Pressing the Fire Drill button activates the system drill response. Pressing the
button a second time cancels the drill response.
Panel Silence: For local systems, pressing the Panel Silence button turns the operator
alert signal off and acknowledges all events have been reviewed.
For proprietary systems, the Panel Silence button is not operational. The operator alert
signal only silences after all events have been acknowledged.
The Panel Silence LED turns on as white while the button is pressed. When the button is
released, the LED is on steady as yellow, indicating the control unit is in an off-normal
condition and the control unit has been placed in Panel Silence mode, and turns off when
the system returns to normal.
Note: The operator alert signal can be configured to resound at a regular interval to
remind the operator that the control unit has been silenced.
Alternate Alarm Sensitivity: Smoke detectors can operate using two levels of
sensitivity: primary and alternate. Pressing the Alternate Sensitivity button switches
Signature detectors to their alternate operating settings. Pressing the button a second
time switches them back to primary sensitivity levels.
Acknowledge: Pressing the Acknowledge button acknowledges events.
For proprietary systems, pressing the Acknowledge button acknowledges an event and
turns the operator alert signal off when all events have been acknowledged in the order
displayed.
when the system returns to normal.
Lamp Test: Pressing the Lamp Test button temporarily turns on all visual indicators on
the local control unit and the LCD screen cycles through colors to reveal any dead pixels.
4 P/N 3102309-EN • REV 001 • ISS 18JUL19


Note: If the local control unit is part of a command center, the lamp test is also executed
on all nodes within the command center.
System Function 1, System Function 2, System Function 3, or System Function 4:
Pressing the System Function button activates the response programmed for function.
None: No action assigned.
8 Alarm Silence button and Pressing the Alarm Silence button turns off the EVAC and ALERT channels, and all
LED (button three) active audible and visible NACs if configured. Pushing the button a second time turns the
notification appliance circuits back on. This button may be used to cancel the drill signal.
The Alarm silence LED turns on as white while the button is pressed. When the button is
released, the LED is on steady as yellow, indicating that the active notification appliance
circuits have been silenced, and turns off when the system returns to normal.
Note: Project configuration settings affect the operation of the Alarm Silence function.
9 Reset button and LED Pressing the Reset button activates the system’s reset sequence to restore the system to
(button four) normal.
The Reset LED turns on as white while the button is pressed. When the button is
released, the LED flashes as green quickly during the smoke power-down phase, flashes
slowly during the power-up phase, is on steady during the restoral phase, and turns off
when the system has reset.
Notes
• The Reset button is disabled as long as the alarm silence inhibit timer is running.
• The Reset button does not affect disabled points or manually overridden functions.
LCD screen indications

The LCD screen on the user interface provides information relevant to the current functional condition of the
control unit. There are two screen modes: system normal and system off-normal (Figure 2 on page 6).
System normal screen: System normal means that the control unit is in the normal (standby) state. In this state,
the LCD screen is clear of any event messages. Only the time, date, system normal graphic, and Action buttons
are displayed.
System off-normal: System off-normal means the control unit has changed to the alarm, trouble, supervisory,
monitor, disabled, or test state. In this state, the screen displays event messages that provide details about what
is happening in the system. The LCD screen displays the eight most recent highest priority events at one time.
P/N 3102309-EN • REV 001 • ISS 18JUL19 5

Figure 2: System normal and off-normal screens
(1) (2)
08/21/2018 12:07:33 Alarm 3 Other 3 08/21/2018 12:07:33

(1) Supervisory 4 Requests 3 Building 1 Disable 2
Trouble 1 Ground 2
Superv- Control
Alarm Trouble isory
(3)
Requests
(2)
Alarm Event List (4)
Alarm: Activate 15:11
1 SouthCampus, Building1, Zone2
(3)
3 (5)
SouthCampus, Building1, Zone2 
(6)
System Project Sign System Project Sign

Holidays (4) Holidays
Info Tree In Info Tree In
System normal screen System off-normal screen

(1) Date (1) Event indicators and event counters. A star
(2) Time designates that there are unacknowledged or new
(3) Default system normal graphic events since the control unit was last silenced.
(4) Action bar (2) Name of displayed event list
(3) List bar
(4) Option buttons for selected action or event list
(5) Acknowledged event indicated by a check mark
(proprietary systems)
(6) Information list
6 P/N 3102309-EN • REV 001 • ISS 18JUL19

LCD screen operator controls

The LCD screen provides list buttons, action buttons, and command buttons that let you operate the control unit,
configure time and date settings, and view system information and event activity.
Figure 3: LCD screen operator controls
(1) Command bar with left and right scroll buttons

Alarm 3 Other 3 08/21/2018 12:07:33
(2) Scroll arrow
Sup 4
Supervisory 4 Requests 3 Building 1 Disable 2
(3) Scroll bar
Trouble 1 Ground 2
(4) Action bar with left and right scroll buttons
Alarm Trouble
Superv-
Sup
Control (5) Interactive information screen
isory Requests
Status History Revision

Test
(1) Note: For a list of interface icon and option button
Indicators
descriptions see. Table 2 below.
(2)
System information
08/21/2018 12:07:01 (3)
Prepared by: [Root\Building 1\FACU 1\Hardware Layer]4CPU
Project Description
IP/DNS node name
Node8030dc90b443
(5) Versions
Configuration 00.00.26.38
Utility
Project 2.3.0.0
Configuration
Project 08/21/2018 11:03:31
Configuration
Date
Project
System Project Sign Holidays

Info Tree In (4)
LCD screen operator interface icons and option buttons

The user interface includes several conditional icons, some of which act as operator controls (option buttons).
Table 2 below provides descriptions of the icons and option buttons that you may see.
Table 2: Operator interface icon and option button descriptions

Icon Description Icon Description
★ ⚇
Appears next to the event indicator Users administration button. Tap to
counters. Designates there are show/hide user PIN.
unacknowledged or new events since
the control unit was last silenced.
Users administration button. Tap to
⌨ Appears next to the signed in user ID. ⎗ save user information.
⟳ Reports option button. Tap to refresh

the report. ☑ Request control button. Tap to grant
control.
🠔🠔 Reports option button. Tap to go to

previous page. ☒ Request control button. Tap to deny
control.
🠖🠖 • Reports option button. Tap to go to

next page. ✆ Fire phone connect button. Tap to
connect a disconnected call.
• Keypad button. Tap to enter and
go to next keypad screen.
P/N 3102309-EN • REV 001 • ISS 18JUL19 7

Icon Description Icon Description
⎙ Printer option button. Tap to send

report to a configured printer. ☎ Fire phone disconnect button. Tap to
disconnect a connected call.
⚲ Details option button. Tap to access an

event details report.
▶∞ Future feature
√ Appears next to acknowledged events

for proprietary mode systems.
▶ 1X Future feature
Keypad delete button. Tap to delete a ▶ 3X Future feature

⌫ character when using the screen
keypads.
☓ User administration button. Tap to

delete a user.
◼ Future feature
✎ Users administration button. Tap to

modify user privileges.
System operation
The basic function of the EST4 control unit is to monitor status changes in the life safety system and to activate
outputs according to the site-specific software. Status change signals, also called events, are classified by type
and mapped into event queues.
Event indicator queues

The event indicator queues that display on the LCD screen are determined by the 4-CPU properties configured
during programming. Events in the queues can pass through to a configured printer, coder, or email service.
The event counters display the number of events in the event queue. A star designates that there are
unacknowledged or new events since the control unit was last silenced.
The queues that appear on the List bar display in order of priority based on programming and market settings.
The project market setting also determines which event types go into each event queue, and their priority.
Unique operator alert signal patterns are assigned to the event queues that alert you to off-normal system
conditions for active event conditions. An alert signal may automatically sound a reminder signal, if configured.
Table 3: Event queues and properties

Event queue Priority level [1] Operator alert signal pattern [2] Event type description
Call In 1 3 pulses every 16 seconds Events that signal a telephone handset is plugged
into a firefighter telephone jack
Control 2 2 pulses every 4 seconds Events that signal a request to take control of the
Request system
Alarm 3 3 pulses every 4 seconds Events that signal fire alarms or other life-
threatening emergencies
Emergency 4 3 pulses every 4 seconds Events that signal mass notification
announcements
Supervisory 5 2 pulses every 4 seconds Events that signal off-normal conditions with
sprinkler and extinguishing systems, and other
equipment related to property safety
8 P/N 3102309-EN • REV 001 • ISS 18JUL19

Event queue Priority level [1] Operator alert signal pattern [2] Event type description
Building 6 2 pulses every 4 seconds Events that signal controlled building equipment
such as dampers, ventilation fans, or temperature
controls are not operating correctly
Disable 7 1 pulse every 4 seconds Events that signal system inputs or system
outputs are disabled
Trouble 8 1 pulse every 4 seconds Events that signal faults within the system
Ground 9 1 pulse every 4 seconds Events that signal ground faults within the system
Other 10 1 pulse every 16 seconds Events that signal the operation of ancillary
equipment
[1] Priority levels shown are for US, Latin America, International, Middle East, and New Zealand markets.
[2] Operator alert signal patterns shown are for the US Market.
Event message lists

Event message lists allow you to view details of messages to help locate devices that are in an abnormal state.
When the system signals a status change, the control unit posts the event message in the appropriate event
message queue and generates a message list for the point that activated the event.
An event message consists of two lines of text, as shown in Figure 4 below. The first line displays the event type,
current status, and time of the event. The second line displays the message text, which is either the address of
the device that activated the event or, if programmed, a location description.
Figure 4: Event message
Alarm 3 Other 3 08/21/2018 12:07:33

Trouble 1 Ground 2
Superv- Control
Alarm Trouble isory Requests
Alarm Event List

3 SouthCampus, Building1, Zone2 
Table 4: Event message behavior for Local and Proprietary modes

Scenario Local mode Proprietary mode
No new events have activated since The highest priority event queue If all events have been acknowledged,
the last time the control unit was silenced displays. the highest priority event queue displays.
New events have activated since the The first new, highest priority event The first unacknowledged event in the
last time the control unit was silenced displays. highest priority queue displays.
An active event is restored The event counter star that indicates The event counter star that indicates
new events disappears. new events disappears and a check
mark appears next to the event
message.
P/N 3102309-EN • REV 001 • ISS 18JUL19 9

User fire privilege levels

Certain user interface controls and functions are protected by a 7-digit PIN and have a fire privilege level that is
determined by the market setting or administrator programming. The privilege levels are summarized Table 5
below.
User sign in times out after a preconfigured period set by the system administrator. The typical user timeout
setting is 5 minutes.
Note: See your system administrator or project documentation for your PIN and fire privilege level.
Table 5: Fire privileges by level

Fire privilege level Privileges
0 (default; no user sign in required) • Reports
• Write access function (1 hour or 8 hour access)
• Print function
• Reset command functions
• Control request, grant, and deny
• Panel Silence button [1][2]
• Drill button [1][2]
• Alternate Alarm Sensitivity button [1][2]
• Acknowledge button [1][2]
• Lamp Test button [1][2]
• System Function button [1][2]
• Alarm Silence button [1]
• Reset button [1]
1 All level 0 privileges, plus:
• Remote read function
• Status holdup report (future feature)
2 (reserved for future features) All level 0 and 1 privileges
3 All level 0, 1, and 2 privileges, plus:
• Freeze history function
• Toggle alternate sensitivity function
• System time and date
• Device (enable/disable)
• Logic groups (enable/disable
• Switch (enable/disable)
• Relay (activate/restore)
• LED (activate/restore)
• Audio amp (activate/restore)
• Audio message (play/stop)
[1] May be programmed for a fire privilege level.
[2] System programming determines the function assigned to button one and button two on the 4-LCD user interface.
10 P/N 3102309-EN • REV 001 • ISS 18JUL19

Using the touch screen

The EST4 LCD touch screen provides interactive operator controls.
• Tap an event message on the information screen to display message details.
• Tap buttons on the Action bar and Command bars to open screens where you can apply system operations
and system functions. See Table 7 and Table 8 on page 13 for details.
• Tap scroll arrows to scroll through system buttons on bars and event messages on the information screen.
• Drag scroll bars to scroll through event messages on the information screen.
List bar
The List bar (Figure 3 on page 7) contains buttons for selecting which event messages you want to display on the
screen. The List bar is only available when the system is off-normal screen.
Up to ten lists may be available based on your control unit configuration and market setting. Tap the left or right
scroll button to view buttons that may be hidden.
Table 6: List bar button descriptions

List Minimum fire Description
privilege level
Call In 0 Displays the Call In event list, which shows firefighter telephone call events stored in the
list, in the order in which they were received.
View an event’s Details Report by tapping the event, and then the details button ⚲. Print
the Details Report by tapping the print button ⎙.
Control 0 Displays the Control Requests event list, which shows a list of control requests and
Requests whether granted or denied, in the order in which they were received.
Alarm 0 Displays the Alarm event list, which shows alarm events stored in the list, in the order in
which they were received.
Emerg 0 Displays the Emergency event list, which shows emergency events stored in the list, in
(Emergency) the order in which they were received.
Supervisory 0 Displays the Supervisory event list, which shows supervisory events stored in the list, in
the order in which they were received.
Building 0 Displays the Building event list, which shows building events stored in the list in the order,
in which they were received.
P/N 3102309-EN • REV 001 • ISS 18JUL19 11

List Minimum fire Description

privilege level
Disable 0 Displays the Disabled event list, which shows disabled events stored in the list, in the
order in which they were received.
Trouble 0 Displays the Trouble event list, which shows trouble events stored in the list in the order,
in which they were received.
the Details Report by tapping the P print button ⎙.
Ground Fault 0 Displays the Ground Fault event list, which shows ground fault events stored in the list, in
the order in which they were received.
Other 0 Displays the Other event list, which shows ancillary events stored in the list in the order in
which they were received.
Action bar
The Action bar (Figure 3 on page 7) contains buttons for selecting system commands. Tapping action buttons
opens system information and interactive screens, and command buttons that are used to apply system
operations. The Action bar is available whether the system is normal or off normal.
The LCD screen displays up to four action buttons at a time. Tap the left or right scroll button to view buttons that
may be hidden.
Table 7: Action bar button descriptions

Action button Minimum fire Description
privilege level
System Info 0 Displays the System information screen, and launches the Command bar that provides
several system operation command buttons.
When signed in as fire privilege level 1 to 3 additional command system operation
buttons appear.
Project Tree 0 Displays the project tree. Use the vertical scroll bar to view hidden sections of the
expanded tree.
• Recent Site Locations: Shows up to 10 locations that the operator has viewed.
• Top level: Expanding the top level of the project tree shows expandable nodes and
branches that can hold hardware, operator, and communication devices.
Tapping a device on the tree, displays its Device details report.
For certain devices, the Command bar launches. The command buttons that appear are
dependent on the fire privilege level of the user.
Sign In 0 Displays a keypad for entering your 7-digit PIN to access to user privileges. The first
three digits of the PIN are your user ID followed by a 4-digit PIN.
Holidays 0 Displays the Holidays List screen.
Users 0 Displays the Users List screen.
12 P/N 3102309-EN • REV 001 • ISS 18JUL19

Action button Minimum fire Description

privilege level
Request control 0 Activates a request to take control of the system and displays the Requests event
indicator/counter, sounds the operator alert signal, and displays the Control Request List
button.
Tapping the Control Requests list button allows you to grant or deny a request. See
“Request Grant Deny logics” on page 55.
Alternate 0 Switches the names on LCD screen buttons, lists, indicators, and the text in primary
language event message to the 4-CU configured alternate language.
(Example:
Española or Note: The alternate language button only appears when the feature is programmed by
English) the system administrator.
Command bar
The Command bar (Figure 3 on page 7) appears when you tap certain action buttons or items on the LCD screen.
For example, if you tap the System Info button, the Command bar appears containing several buttons that include
allowing you to enable and disable devices and zones, activate and restore switch outputs, and view system
reports.
The LCD screen displays up to four command buttons at a time. Tap the left or right scroll button to view buttons
that may be hidden.
Table 8: Command bar button descriptions

Action button Command button Minimum fire Description
privilege level
System Info System Info 0 System information report. Lists the control unit firmware version,
SDU and hardware configurations, and licensing information.
Status 0 Status (all) report. Lists active events and disabled points from the
selected node.
Status Disabled 0 Status (disabled) report. Lists all addressable points that are in the
disabled state.
Status Test 0 Status (test) report. Lists off-normal devices under test.
History 0 History – All Dates report. Lists the last 20,000 events and
operator commands processed by the selected node.
History Alarm 0 History – All Dates, Alarm report. Lists the event name, time, date,
and location text for all alarm events.
History Trouble 0 History – All Dates, Trouble report. Lists the event name, time,
date, and location text for all trouble events.
History Supervisory 0 History – All Dates, Supervisory report. Lists the event name, time,
date, and location text for all supervisory events.
Maintenance (all) 0 Maintenance report. Lists the %Dirty value for all of the detectors
on a signaling line circuit for the selected node. For CO detectors
the report includes CO Life Left Months or CO DAY Running. The
report includes each detector’s model type, primary and alternate
alarm sensitivity values, and, if programmed, a location
description.
Maintenance Dirty 0 Maintenance (dirty) report. Lists all addressable smoke detectors
that have a %Dirty value 20% and greater. A smoke detector that
is more than 20% dirty should be noted for possible cleaning or
replacing.
P/N 3102309-EN • REV 001 • ISS 18JUL19 13


privilege level
Maintenance Not 0 Maintenance (not clean) report. Lists all addressable smoke
Clean detectors that have a %Dirty value of 80% and greater. Smoke
detectors that are more than 80% dirty should be cleaned or
replaced as soon as possible.
Maintenance 0 Maintenance report. Lists the %Dirty value for a selected detector
(device) on a signaling line circuit. The report includes the detector’s model
type, primary and alternate alarm sensitivity value, and, if
programmed, a location description.
Revision 0 Revision report. Creates a report that lists the revision level of all
the hardware and software components installed in a node
selected in the project tree.
1 Hour Access 0 Provides a validation code that unblocks the Remote Write
command for one hour to permit database changes. The code
must be entered in the 4-CU to allow database downloads from a
programming computer to the 4-CPU in the EST4 control unit.
When tapped, the operator alert sounds and the Other command
button displays to show the “Remote write unlocked” local monitor
event.
8 Hour Access 0 Provides a validation code that unblocks the Remote Write
command for eight hours to permit database changes. The code
must be entered in the 4-CU to allow database downloads from a
programming computer to the 4-CPU in the EST4 control unit.
When tapped, the operator alert sounds and the Other command
button displays to show the “Remote write unlocked” local monitor
event.
Cancel Access 0 Immediately restores the Remote Write command and prevents
access to database changes.
Reset 0 Resets the local control unit. When tapped, the Reset control
button indicator flashes.
Reset All 0 Resets all networked nodes. When tapped, the Reset control
button indicator flashes.
Test Indicators 0 Activates a test of all control unit LEDs and installed control-
display module LEDs.
Status Holdup 1 Future feature.
Lock Incoming 1 Blocks web services for all 4-FWAL series nodes.
Network
Unlock Incoming 1 Unblocks web services for all 4-FWAL series nodes.
Network
Freeze History 3 Archives the most recent events (up to 10,000 events) so that they
cannot be overwritten.
Toggle Alternate 3 Switches detector alarm sensitivity levels from primary to alternate
Sensing or from alternate to primary, whichever is currently active.
Set Date Time 3 Opens a keypad that lets you set the system time and date.
Project Tree Enable 3 Enables a device selected in the project tree.
Disable 3 Disables a device selected on the project tree.
Activate 3 Activates AND groups and command lists selected in the project
tree.
Restore 3 Restores AND groups the command lists.
On 3 Activates input and output devices selected in the project tree.
14 P/N 3102309-EN • REV 001 • ISS 18JUL19


privilege level
Off 3 Restores the input and output devices.
On 3 Turns on a control-display LED selected in the project tree to
steady.
Fast Blink 3 Turns on a control-display LED selected in the project tree to fast
blink.
Slow Blink 3 Turns on a control-display LED selected in the project tree to slow
blink.
Off 3 Turns off the control-display LED.
▶∞ 3 Future feature.
◼ 3 Future feature.
▶ 1X 3 Future feature.
▶ 3X 3 Future feature.
P/N 3102309-EN • REV 001 • ISS 18JUL19 15

16 P/N 3102309-EN • REV 001 • ISS 18JUL19

Chapter 2
Basic operating instructions
Summary
This chapter provides instructions for operating the basic features of your EST4 life safety system. Basic features
are those that typically do not require a fire privilege PIN.
Content
Silencing the operator alert signal 18
Silencing alarm signals 18
Acknowledging events 19
Displaying event lists 19
Viewing event details 20
Changing the LCD screen to an alternate
language 21
Viewing the alarm count 22
Checking system device statuses 22
Performing a lamp test 22
Activating an alarm signals drill 23
Resetting the life safety system 23
Finding detectors needing maintenance 24
Viewing history reports 24
Finding firmware and system information 25
Revision report 25
System Information report 26
Obtaining and canceling write access for system
downloads 26
Requesting, granting, or denying control 27
Using the 4-LCD user interface to request, grant,
or deny control 27
Using a control-display module to request, grant, or
deny control 27
Making voice and emergency announcements 28
4-MIC microphone 28
4-MIC live mass notification signaling (MNS) 30
4-FT firefighter telephone live voice
announcements 31
4-FT firefighter telephone two-way
communication 32
P/N 3102309-EN • REV 001 • ISS 18JUL19 17

Chapter 2: Basic operating instructions
Silencing the operator alert signal

The control unit sounds the operator alert signal when an event message is posted into one of the event message
queues. Pressing the Panel Silence button silences the operator alert signal.
Notes
• Pressing the Panel Silence button may also silence the operator alert signal on remote annunciators, if the
system is configured to do so.
• For proprietary systems, the Panel Silence button is not operational. The operator alert signal only silences
after each event has been individually acknowledged (see “Acknowledging events” on page 19).
• The control unit panel silence function can be programmed for a fire privilege level. The default setting is no
PIN required.
To silence the panel operator alert signal:

1. Press the Panel Silence operator control button.
2. If prompted, enter the fire privilege PIN using the interactive keypad.
Silencing alarm signals

WARNING: Death or serious injury. The protected premises may be occupied. Do not silence alarm signals or
reset the control unit unless you are authorized to do so and only after all occupants have been evacuated.
Pressing the Alarm Silence operator control button silences all audible alarm signals and, if configured, all visual
alarm signals. Pressing the button a second time turns back on the signals.
Pressing the Alarm Silence operator control button does not silence alarm signals when:
• A waterflow alarm switch is active and the system is configured to prevent silencing alarm signals when a
waterflow alarm switch is active
• The system is configured to delay the silencing of alarm signals, in which case the Alarm Silence button may
not be operational for up to five minutes following the first alarm event
Silenced outputs automatically re-sound when:
• The Alarm Silence button is pressed a second time
• Another alarm input activates
• Another alarm input in the same zone activates, unless the system is configured to prevent alarm signals from
re-sounding
Note: The alarm silence function can be programmed for a fire privilege level PIN. The default setting is no PIN
required.
To silence alarm signals:

1. Press the Alarm Silence operator control button.
18 P/N 3102309-EN • REV 001 • ISS 18JUL19

Acknowledging events
When an event occurs, it is important that you acknowledge it and review the issue. The control unit handles the
event by showing it on the LCD screen as an event message, sounding the operator alert signal, placing the
event in the appropriate queue, and, when configured, flashing the Acknowledge LED.
If an operator control button has been programmed in the 4-CU as Acknowledge, pressing the Acknowledge
button acknowledges events.
For proprietary systems, pressing the Acknowledge button acknowledges an event and turns the operator alert
signal off after all events have been individually acknowledged in the order displayed.
Note: The acknowledge function can be programmed for a fire privilege PIN. The default setting is no PIN
required.
To acknowledge an event:
1. Press the Acknowledge operator control button.
Displaying event lists

Event lists allow you to view event messages in a specific queue. The message consists of two lines of text that
include the event type, current status, time of the event, and message text.
Figure 5: Viewing event lists
Alarm 3 Other 3 08/21/2018 12:07:33

Trouble 1 Ground 2
Superv- Control
(1) Alarm Trouble isory Requests
Alarm Event List

(2) 3 SouthCampus, Building1, Zone2 

Info Tree In
(1) Event list buttons (2) Events in the list queue
P/N 3102309-EN • REV 001 • ISS 18JUL19 19

To display an event list:

1. Tap an event list button. For example, Alarm.
A list of queued events appears on the information screen.
Viewing event details

An event or device details report provides the type of event, address of the device that generated the event and, if
programmed, the location (Figure 6 below).
Device details: If a device activation causes an event, the Details screen shows the active device’s logical
address and the off-normal state.
Logic group details: If a group activation causes an event, the Details screen shows the state of the device,
device address, and device message, which is usually the device location.
Instruction text details: If the system administrator has programmed detailed instructions for certain events to
show, when specific devices go into alarm the system generates a related monitor event. If you select the monitor
event, and then press the details button the instruction text is displayed.
Figure 6: Event details report
Alarm 3 Other 3 08/21/2018 12:07:33

Trouble 1 Ground 2
Superv- Control
Alarm Trouble isory Requests
Report
Device details
08/21/2017 12:07:01
User interface
[Root\Building 1\FACU 1\Hardware Layer]MODCOM]
$AnnunciatorSupervision
Prepared by: [Root\Building 1\FACU 1\Hardware Layer]4CPU
Report end

Info Tree In
Event details can be accessed from the event list or project tree.
20 P/N 3102309-EN • REV 001 • ISS 18JUL19

Figure 7: Accessing event details
(1) (5)
Alarm 3 Other 3 08/21/2018 12:07:33 Alarm 3 Other 3 08/21/2018 12:07:33
Supervisory 4 Requests 3 Building 1 Disable 2 Supervisory 4 Requests 3 Building 1 Disable 2
Trouble 1 Ground 2 Trouble 1 Ground 2
Superv- Control Superv- Control

(2) Alarm Trouble isory Alarm Trouble
Requests isory Requests
Alarm Event List (4) Disable Enable Activate Restore

(3) 1 SouthCampus, Building1, Zone2 (6) Recent locations
Alarm: Activate 11:13 (7)
2 Root
SouthCampus, Building1, Zone2
Alarm: Activate 11:13 Node 0
3 SouthCampus, Building1, Zone2 
Hardware Layer
LRM
Operator Layer
Communication Services
South Campus
NCA 1
RGD 1
System Project Sign System Project Sign Holidays

Holidays
Info Tree In Info Tree In
(1) Event List screen (5) Project tree screen

(2) Event List buttons (6) Expand button
(3) Event number button
(7) Collapse button
(4) Event details button
To view device details from an event list:

1. Tap an event List button. For example, Alarm.
2. In the list, tap the event number, and then tap the details button ⚲. The Device Details Report displays.
To view device details from the project tree:

1. On the Action bar, tap Project Tree.
2. Expand the project tree by tapping the expand button , and then locate the target device or pseudo point.
3. Tap on the device/pseudo point. The Device Details Report displays.
Changing the LCD screen to an alternate language

For control units programed for an alternate language, a language button displays on the Action bar. The button
name shows the alternate language configured for the control unit. For example, Española or English.
When the alternate language button is tapped, the names on LCD screen buttons, lists, and indicators and the
text in primary event messages switches to the alternate language.
Notes
• For the alternate language button to appear on the Action bar, the Alternate Language property must have
been programmed.
P/N 3102309-EN • REV 001 • ISS 18JUL19 21

• Custom event message text does not switch to the alternate language.
• The LCD screen defaults to the primary language at control unit startup.
To change the LCD screen to the alternate language:

1. Tap the alternate language button on the Actions bar (example: Española or English).
Viewing the alarm count

The EST4 control unit records how many times it has gone into alarm condition since the alarm history was
cleared. View the Revision report to see the alarm count.
To view the alarm count:

1. On the Action bar, tap System Info.
2. On the Command bar, tap the Revision button. Alarm history count displays in the top of the Revision report.
You can tap the print button ⎙ to send the report to a local printer.
Checking system device statuses

The EST4 control unit provides the following status reports to help you find out if any points in the system are in
an active or other off-normal state:
• Status report: Shows a list of all active events and disabled points from the selected node.
• Status Test report: Shows a list of off-normal devices under test.
• Status Disabled report: Shows a lists of addressable points that are disabled.
To view device status reports:

2. On the Command bar, tap the desired device status report button. The report displays on the screen.
You can tap the print button ⎙ to send the report to a local printer.
Performing a lamp test

A lamp test allows you to verify the operation of the LCD screen and LED indicators. The test temporarily turns on
the operator alert signal, all LED indicators, and every pixel on the LCD screen.
You can activate a lamp test using an operator control button, when programmed as Lamp Test, or a control-
display module button programmed to activate the lamp test.
Notes
• If the local control unit is part of a command center, the lamp test is also executed on all nodes within the
command center.
• The lamp test function can be programmed for a fire privilege PIN. The default setting is no PIN required.
22 P/N 3102309-EN • REV 001 • ISS 18JUL19

To activate a lamp test:

1. Press the Lamp Test operator control button, if available
— or —
Press a control-display button programmed to activate the lamp test.
Activating an alarm signals drill

The EST4 drill feature lets you activate alarm signals manually without putting the control unit into alarm. When
you activate a drill, all audible alarm signals turn on and, if configured, all visual alarm signals, but other automatic
fire alarm responses are not activated. The alarm signals remain active until the drill is canceled.
You can activate a drill using an operator control button, when programmed as Fire Drill, or a control-display
module button programmed to activate the drill.
Note: The drill function can be programmed for a fire privilege PIN. The default setting is no PIN required.
To activate a drill:
1. Press the Fire Drill operator control button if available
— or —
Press a control-display button programmed to activate the drill.
Note: To cancel the drill, press the button a second time.
Resetting the life safety system

WARNING: Death or serious injury. The protected premises may be occupied. Do not reset the fire alarm system
until the proper authorities have determined that the threat of fire is no longer present.
Resetting the life safety system restores the system to its normal state, provided all latched inputs have been
restored before the end of the reset cycle.
Notes
• The Reset button may be inoperable for up to three minutes following the first alarm event.
• The Reset button does not affect disabled points or manually overridden functions.
• The reset function can be programmed for a fire privilege PIN. The default setting is no PIN required.
To reset the life safety system:

1. Press the Reset operator control button.
P/N 3102309-EN • REV 001 • ISS 18JUL19 23

Finding detectors needing maintenance

The EST4 control unit provides maintenance reports to help you find out if any addressable smoke detectors need
servicing. The %Dirty value shown in the report is an indication of a smoke detector’s ability to compensate for
environmental conditions. Smoke detectors with higher percentages are less able to compensate.
The following maintenance reports can be accessed from the control unit'
• Maintenance (all): Lists the %Dirty value for all of the smoke detectors on a signaling line circuit. The report
also includes each smoke detector’s model type, primary and alternate alarm sensitivity values, and, if
programmed, a location description.
• Maintenance (device): Lists the %Dirty value for a single smoke detector. For CO detectors the report
includes CO Life Left Months or CO DAY Running. The report also includes the smoke detector’s model type,
primary and alternate alarm sensitivity values, and, if programmed, a location description. To view this report
you must select the device from the Project Tree.
• Maintenance Not Clean: Lists all addressable smoke detectors that have a %Dirty value of 80% and greater.
Smoke detectors that are more than 80% dirty should be cleaned or replaced as soon as possible.
• Maintenance Dirty: Lists all addressable smoke detectors that have a %Dirty value of 20% and greater. A
smoke detector that is more than 20% dirty should be noted for possible cleaning or replacing.
To find detectors that may need servicing:

2. On the Command bar, tap the desired maintenance report button. The report displays on the screen.
Tap the print button ⎙ to send the report to a local printer.
To view a maintenance report for a specific detector:

1. On the Action bar, tap Project Tree.
2. Expand the project tree by tapping the expand button , and then locate the target detector. For example,
FLR1W PCOS2.
3. Tap the detector. The Device Details screen appears.
4. On the Command bar, tap the Maintenance button.
Viewing history reports

The EST4 control unit provides history reports that list the most recent events or operator instructions processed
by the control unit for the previous month to current or since its history was cleared. The report includes the event
or system command name, address, time and date of occurrence, and the source that initiated the event or
command.
The history reports are listed below.
• History: All Dates report: Lists the last 20,000 events and operator commands processed by selected node
• History Alarm: All Dates, Alarm report: Lists the event name, time, date, and location text for all alarm events
• History Trouble: All Dates, Trouble report: Lists the event name, time, date, and location text for all trouble
events.
• History Supervisory: All Dates, Supervisory report: Lists the event name, time, date, and location text for all
supervisory events.
24 P/N 3102309-EN • REV 001 • ISS 18JUL19

To view history reports:

2. On the Command bar, tap the desired history report button. The report displays on the screen.
Finding firmware and system information

The EST4 control unit provides revision and system information reports where you can find unit database,
firmware, and project versions, device firmware numbers, MAC addresses, and other system information.
Revision report
The Revision report provides system database information and installed hardware information. The hardware that
shows on the list is dependent on the devices installed in the control unit cabinet.
By viewing a Revision report, you can find information for the following:
• Alarm history count: Shows the total number of times that the control unit has gone into alarm since the alarm
history was cleared.
• Market: Shows the 4-CU market setting.
• Configuration version: Shows the 4-CU project version number.
• Configuration time stamp: Shows the date and time that the 4-CU project was created or modified.
• Configuration schema: Shows the 4-CU firmware-to-software interface version.
• Configuration messaging: Shows the 4-CU internal messaging protocol version.
• Firmware: Shows the 4-CU firmware version.
• Local rail module (LRM) shows:
– LRM type
– Firmware version and date
– Bootloader version and date
– 4-CU database version and date
• Control-display module (CDM) Annunciator shows:
– CDM type
• CPU shows:
– CPU type
– Bootloader version and date.
To view the Revision report:

2. On the Command bar, tap the Revision button. The Revision report displays on the screen.
P/N 3102309-EN • REV 001 • ISS 18JUL19 25

System information report

The System Info report provides a project description that includes the control unit (node) MAC address required
for communication between the 4-CU and control unit, and project versioning numbers. Component licensing and
copyright information is also included in the report.
By viewing the System Info report, you can find information for the following:
Project Description
• IP/DNS node name: Shows the MAC address of the installed CPU.
Versions
• Configuration Utility: Shows the 4-CU software version.
• Project Configuration: Shows the 4-CU project version number.
• Project Configuration Date: Shows the date and time that the database was downloaded.
• Project Configuration ID: Shows the database serial number created when the database was converted.
• Configuration schema: Shows the 4-CU software-to-firmware interface version.
• Message Schema: Shows the 4-CU internal messaging protocol version.
• Firmware: Shows the 4-CU firmware version.
• Archive Enabled: Shows whether the project is configured to automatically archive project files.
Licensing
• Licensing and copyright information for various components used in the 4-CU software and firmware.
To view the System Information report:

1. On the Action bar, tap System Info. The System Information report displays on the screen.
Obtaining an access code for a system programmer

A system programmer downloads firmware and project databases to the control unit from a computer running the
system configuration utility. By default, the control unit is blocked from allowing unauthorized database changes.
The programmer may request that you obtain a control unit access code to gain access for a system download.
Note: The access code should only be used by a system programmer or service provider. Changes to the life
safety system must be tested and may require local authority approval.
To obtain an access code:

2. On the Command bar, tap 1 Hour Access or 8 Hour Access. A 6-digit access code displays.
To cancel access:
2. On the Command bar, tap Cancel Access.
26 P/N 3102309-EN • REV 001 • ISS 18JUL19

Requesting, granting, or denying control

The request, grant, deny (RGD) function is a programming method working in association with notification control
areas and command centers to handle demands for control of audio communications in the life safety system.
Request to control a system and permission to grant or deny the request can be made from the 4-LCD user
interface or from programmed control-display module button.
Using the 4-LCD user interface to request, grant, or deny control

To request control:
1. On the Action bar, tap Request Control. The Control Request list button appears and the operator alert signal
sounds.
2. Tap the Control Request list button.
The Control Request List screen shows the request for control locations and the control status. You can tap
the details button ⚲ to see the control status, which displays on the Device Details report.
To grant control:
2. On the Control Request List screen, tap the desired control request number, and then tap the grant button ☑.
Note: The grant button is functional only on the node that has control.
The control status shows on the screen. You can tap the details button ⚲ to see the control status, which
displays on the Device Details report.
To deny control:
2. On the Control Request List screen, tap the desired request number, and then tap the deny button ☒.
The control status shows on the screen. You can tap the details button ⚲ to see the control status, which
displays on the Device Details report.
Using a control-display module to request, grant, or deny control

Note: Your system may be configured and labeled differently than shown in the example provided in Figure 8 on
page 28.
P/N 3102309-EN • REV 001 • ISS 18JUL19 27

Figure 8: Example of the request, grant, deny function using a control-display module
(1) Control status indicators

Control
Status (1) Top indicator is steady when the local unit is in control
Request
Bottom indicator is steady when the local unit is not in control
Control (2)
Grant
(2) Request Control indicators and switch
(3)
Control Indicator is flashing when a request for control is received
Deny (4)
Control (3) Grant Control s and switch
Indicator is flashing when a request for control is granted
(4) Deny Control indicators and switch
Indicator is flashing when a request for control is denied
To request control:
1. From the control-display module, press the switch labeled to request control. For example, “Request Control”
in Figure 8, item 2.
To grant control:
1. When the control display module’s request for control indicator (Figure 8, item 2) is flashing, press the switch
labeled to grant control. For example, “Grant Control” in Figure 8, item 3.
To deny control:
1. When the control-display module’s request control indicator (Figure 8, item 2) is flashing, press the switch
labeled to deny control. For example, “Deny Control” in Figure 8, item 4.
Making voice and emergency announcements

For an EST4 control unit that includes a 4-MIC microphone or 4-FT firefighter telephone, emergency voice and
alarm communications are supported.
4-MIC microphone
The 4-MIC microphone provides paging capability local to the node, within an notification control area (NCA), or
over an entire network. The 4-MIC assembly incorporates push-to-talk (PTT) LED that illuminates when the PTT
button is pressed, and a volume LED that illuminates if the voice level is too loud.
Notes
• All paging functions require a 4-24L series control-display module.
• Your system may be configured differently than described below.
28 P/N 3102309-EN • REV 001 • ISS 18JUL19

To make a live voice announcement:

1. For a control unit programmed as a command center, request for control of the EST4 system may be
required.
• Using the operator touch screen:
On the Action bar tap Request Control, and then tap the Control Request list button. The information
screen will show the control status. When ready, proceed to step 2.
• Using a 4-24L series control-display module (see Figure 9 below):
If the top Control Status LED (item 4) is steady, proceed to step 2. If not, press Request Control (item 5);
its LED flashes while requesting control. When the top Control Status LED is steady, proceed to step 2.
Figure 9: 4-MIC voice announcements using control-display module switches and indicators
4-MIC 4-24L12S
(1) READY TO PAGE

Control MNEC
Status (4) On
Request MNEC
(2) Control (5) Reset
PAGING VOLUME
Grant MNEC
Control Silence
Deny
(3) Control
All Call (6)

All Call
Minus (7)
Phone
Page
Page to
Other (8)
Page to
Emerg (9)
EVAC (10)
Alert (11)
2. Remove the microphone from its hook, and then press the areas to receive the page.
All Call (item 6): Broadcasts to all areas whether or not they are sounding a signal.
All Call Minus (item 7): Broadcasts to areas not currently sounding the evacuation signal or the alert signal.
Page to Other (item 8): Broadcasts live voice messages to areas such as stairwells and elevators.
Page to Emerg (item 9): Broadcasts live voice messages to areas defined for mass notification
announcements.
EVAC (item 10): Broadcasts to areas currently sounding the evacuation signal.
Alert (item 11): Broadcasts to areas configured to areas currently sounding the alert signal.
3. Press and hold the microphone push-to-talk switch (PTT) (item 3). The Ready to Page LED (item 1) flashes
during a preannouncement tone. When the LED is on steady, begin the announcement. Adjust your voice
level so that the red LED on the Paging Volume meter (item 2) does not illuminate.
4. Release the PTT switch when the announcement is finished and return the microphone to its hook.
P/N 3102309-EN • REV 001 • ISS 18JUL19 29

4-MIC live mass notification signaling (MNS)

In MNS signaling mode, the page signal is redirected to the Emergency channel. Any audio amplifier connected to
either the Page or Emergency audio channels will receive the page.
Notes
• All paging functions require a 4-24L series control-display module.
To make a live mass notification announcement:

required.
• Using the operator touch screen:
On the Action bar tap Request Control, and then tap the Control Request list button. The information
screen will show the control status. When ready, proceed to step 2.
• Using a 4-24L series control-display module (see Figure 10 below):
If the top Control Status LED (item 4) is steady, proceed to step 2. If not, press Request Control (item 8);
its LED flashes while requesting control. When the top Control Status LED is steady, proceed to step 2.
Figure 10: 4-MIC live MNS signaling using control-display module switches and indicators
4-MIC 4-24L12S
(4)
(1) READY TO PAGE
Control MNEC
Status On (5)
Request MNEC
(2) Control Reset (6)
PAGING VOLUME
Grant MNEC
Control Silence (7)
Deny (8)
(3) Control
All Call (9)

All Call
Minus
Phone
Page
Page to
Other
Page to
Emerg
EVAC
Alert
2. Press the MNEC On button (item 5) on the control-display module, to activate the function.
3. Remove the microphone from its hook, and then press the All Call button (item 9) on the control-display
module.
4. Press and hold the microphone push-to-talk switch (PTT) (item 3). The Ready to Page LED (item 1) flashes
during a preannouncement tone. When the LED is on steady, begin the announcement. Adjust your voice
level so that the red LED on the Paging Volume meter (item 2) does not illuminate.
5. Release the PTT switch when the announcement is finished and return the microphone to its hook.
30 P/N 3102309-EN • REV 001 • ISS 18JUL19

To silence mass notification signals:

1. Press MNEC Silence (figure item 7 above). The bottom LED indicates silence is active.
Note: This action only silences mass notification signals. To silence fire alarm signals, see “Silencing the operator
alert signal” on page 18.
To reset the system when mass notification operation is active:

1. Press MNEC Reset (figure item 6 above) on the control-display module. The bottom LED indicates the reset
is active.
Note: This action only resets the system when mass notification operation is active. To reset the system for fire
events, see “Resetting the life safety system” on page 23.
4-FT firefighter telephone live voice announcements

For an EST4 system that includes a firefighter telephone, the telephone paging feature permits individuals with
access to a remote firefighter telephone to make announcements over the emergency voice/alarm
communications system.
Notes
• All 4-FT live voice announcement functions require a 4-24L series control-display module.
To make a live voice announcement:

required. Use a 4-24L series control-display module to request control. See Figure 11 below.
If the top Control Status LED (item 1) is steady, proceed to step 2. If not, press Request Control (item 2); its
LED flashes while requesting control. When the top Control Status LED is steady, proceed to step 2.
Figure 11: 4-FT live voice announcements using control-display module switches and indicators
4-FT 4-24L12S
Control
Status (1)
Request
Control (2)
Grant
Control
Deny
Control
Ready (3)
to Page
Phone
Page (4)
2. Remove the telephone handset from its hook.

3. The Ready to Page LED (item 3) on the control-display module flashes during a preannouncement tone.
When the LED is on steady, begin your announcement.
4. When finished, place the telephone handset on its hook.
P/N 3102309-EN • REV 001 • ISS 18JUL19 31

4-FT firefighter telephone two-way communication

The 4-FT firefighter telephone provides capability for two-way communications between the fire command station
and firefighter telephone stations / jack telephones installed at strategic locations throughout the protected
building.
Answering incoming calls

An incoming call is initiated when a 4-FT firefighter telephone is taken off-hook or plugged into a telephone jack,
generating a visual and audible incoming call signal at the fire command station. The caller hears a tone until the
handset is connected to the system. The fire command station operator manually connects the incoming phone
call to the phone riser to complete the call. The firefighter telephone can also be used as a page source.
The incoming call sounds the control unit operator alert signal and displays the Call-in List button on the LCD
screen that, when tapped, displays a Call-in list of all incoming calls in the order in which they were received. Call-
in icons also appear that serve as operator controls for connecting and disconnecting calls.
To answer a call:
required. Use a 4-24L series control-display module to request control. See Figure 11 on page 31.
If the top Control Status LED (item 1) is steady, proceed to step 2. If not, press Request Control (item 2); its
LED flashes while requesting control. When the top Control Status LED is steady, proceed to step 2.
2. From the operator touch screen, on the List bar, tap Call-in.
3. In the Call-in List, locate the desired call, and then tap the call-in event number.
Figure 12: Answering firefighter telephone calls using the operator touch screen
4. Tap the connect button ✆ to connect the call to the master (local) telephone handset. The event’s status
changes to Connected.
5. Remove the telephone from its hook and communicate with the caller.
6. To add another call-in location to the conversation, in the Call-in list tap the location’s event number, and then
tap Connect again.
Up to five phone circuits can be connected, in addition to the master telephone.
32 P/N 3102309-EN • REV 001 • ISS 18JUL19

Disconnecting calls
When the caller is ready to hang up or remove a phone from its jack, disconnect the call.
To disconnect a call:
1. On the Call in List, locate the call to be disconnected, and then tap the call-in event’s number.
2. Tap the disconnect button ☎ to disconnect the call. The event status changes to Disconnected.
When the remote telephone handset is hung up or removed from the phone jack, the call will be removed
from the Call-in list.
3. Place the master telephone handset on its hook. The Call-in event indicator and Call-in list no longer appear
on the LCD screen.
P/N 3102309-EN • REV 001 • ISS 18JUL19 33

34 P/N 3102309-EN • REV 001 • ISS 18JUL19

Chapter 3
Advanced operating
instructions
Summary
This chapter provides instructions for operating the advanced features of your EST4 life safety system. Advanced
features alter system operation and require the fire privilege 1 access or greater.
Content
Changing remote read access 36
Freezing the events history 36
Changing the smoke detector alarm sensitivity
threshold 36
Setting the system date and time 37
Disabling and enabling devices 37
Disabling and enabling local rail modules 38
Disabling and enabling logic groups 39
Disabling and enabling time controls 39
Changing output states 40
Control-Display modules 40
Disabling and enabling control-display
modules 41
Disabling and enabling control-display module
elements 41
P/N 3102309-EN • REV 001 • ISS 18JUL19 35

Chapter 3: Advanced operating instructions
Changing web service access

You can block and unblock web services for all firewall nodes using a user interface command button.
Note: Only users with fire privilege 1 and higher can access this function.
To allow remote read access:

1. Sign in with fire privilege 1 or higher, and then tap System Info on the Action bar.
2. On the Command bar, tap Unlock Incoming Network. This unblocks web services for all firewall nodes.
To disallow remote read access:

1. Sign in with fire privilege 1 or higher, and then tap System Info on the Action bar.
2. On the Command bar, tap Lock Incoming Network. This blocks web services for all firewall nodes.
Freezing the events history

When the Freeze History command is activated, the system archives the most recent events (up to 10,000) so
that they cannot be overwritten.
Note: Only users with fire privilege 3 can access this function.
To freeze event history:

1. Sign in with fire privilege 3, and then tap System Info on the Action bar.
2. On the Command bar, tap Freeze History.
Changing the smoke detector alarm sensitivity threshold

Intelligent addressable smoke detectors are configured with two alarm sensitivity thresholds: primary and
alternate. The alarm sensitivity setting determines how easily automatic fire detectors can sense a fire alarm
condition.
A time control is commonly used to automatically switch alarm sensitivity thresholds. However, you can manually
switch alarm sensitivity thresholds by using a command button.
Primary alarm sensitivity threshold: Typically, the primary alarm sensitivity threshold is set to a lower
threshold. This threshold is commonly used for a daytime operation to reduce the occurrence of nuisance alarms
when a facility is occupied, or when environmental conditions may create prealarm conditions.
Alternate alarm sensitivity threshold: The alternate alarm sensitivity threshold sets the secondary threshold at
which the smoke detector activates an alarm event. Typically, the alternate threshold is set to a higher sensitivity
threshold. This threshold is commonly used for a nighttime or weekend operation, when the facility is unoccupied.
To activate the alternate alarm sensitivity settings:

2. On the Command bar, tap Toggle Alternate Sensing.
36 P/N 3102309-EN • REV 001 • ISS 18JUL19

To restore the primary alarm sensitivity settings:

2. On the Command bar, tap Toggle Alternate Sensing.
Setting the system date and time

The control unit incorporates a system clock to time stamp events and to activate time controls. The time is
presented in 24-hour format. The date format is determined by the 4-CU project property setting. The default
format is presented in month-day-year.
To set the system date and time:

2. On the Command bar, tap Set Date Time.
3. Use the interface keypad to enter date and time.
The default format is YYYYMMDDhhmmss. Where,
YYYY = 4-digit year
MM = 2-digit month
DD = 2-digit day
hh = 2-digit hour
mm = 2-digit minutes
ss = 2-digit seconds
Note: The time is entered in 24-hour format, for example:
000000 = midnight
010000 = 1:00 a.m.
120000 = noon
130000 = 1:00 p.m.
235900 = 11:59 p.m.
The date and time, displayed at the top of the user interface screen, immediately changes.
Disabling and enabling devices

Disabling a device isolates it from the system. While the device is disabled, the EST4 control unit logs the status
change signals, but is prevented from processing the signals until the device is enabled. For example, the control
unit does not activate an alarm event when you activate a disabled detector, but it will after the detector is
enabled.
The control unit keeps track of how many times you disable a device without enabling it. You must enable a
device the same number of times you disable it in order to return the device to its original condition. The Status
Disabled report provides a counter that shows the number of times the device was manually disabled.
Notes
• Disabling the device address for a dialer or a dialer account deletes all event messages sent to that account
before they are transmitted. However, the dialer still transmits the account’s test-abnormal message and any
message that was in the dialer queue before the account was disabled.
P/N 3102309-EN • REV 001 • ISS 18JUL19 37

• Disabling all of the devices in a zone group automatically disables the zone group. Enabling any device in the
zone group automatically enables the zone group.
• When you enable a device, all indicators and outputs activated by the device will reactivate.
• Only users with fire privilege 3 can access this function.
To disable a device:
1. Sign in with fire privilege 3, and then tap Project Tree on the Action bar.
2. Expand the project tree by tapping the expand button , and then locate the target device.
3. Tap the device, and then tap Disable on the Command bar.
To enable a device:
3. Tap the device, and then tap Enable on the Command bar. You must enable the device the same number of
times that you disabled it. If necessary, view the Status Disabled report to see the manual disable counter
(Action Bar > System Info > Status Disabled).
Disabling and enabling local rail modules

Local rail modules can include chassis rail cards and modules installed on the backbox, and control-display
modules installed on the inner door. Disabling a module isolates it from the system. While the module is disabled,
the EST4 control unit logs the status change signals, but is prevented from processing the signals until the
module is enabled.
Notes
• The control unit keeps track of how many times you disable a module without enabling it. You must enable a
module the same number of times you disable it in order to return the module to its original condition. The
Status Disabled report provides a counter that shows the number of times the device was manually disabled.
To disable an LRM:
2. Expand the project tree by tapping the expand button , and then locate the target LRM.
3. Tap the module, and then tap Disable on the Command bar.
To enable an LRM:
2. Expand the project tree by tapping the expand button , and then locate the target LRM.
3. Tap the module, and then tap Enable on the Command bar. You must enable the device the same number of
38 P/N 3102309-EN • REV 001 • ISS 18JUL19

Disabling and enabling logic groups

A group is a logic device that is created during system programming. Your system configuration may include
AND, Matrix, Service, Zone, or Instruction Text logic groups.
Logic groups are required in order to execute certain system functions, but have no physical relationship to the
system. For example, smoke detectors can be assigned to the same Zone group even though they are not
attached to the same wire run.
Disabling a logic group isolates it from the system. While the group is disabled, the control unit is prevented from
processing status change signals from every device in the group until the device is enabled. For example in a
Zone group, the control unit does not activate an alarm event when you activate a disabled detector, but it will
after the detector is enabled.
Notes
• The control unit keeps track of how many times you disable a logic group without enabling it. You must enable
a logic group the same number of times you disable it in order to return the group to its original condition. The
Status Disabled report provides a counter that shows the number of times the device was manually disabled.
• If you disabled a Zone logic group by disabling all of the devices in the zone, enabling the zone enables all of
the devices in the zone.
To disable a logic group:

2. Expand the project tree by tapping the expand button , and then locate the target group.
3. Tap the group, and then tap Disable on the Command bar.
To enable a logic group:

2. Expand the project tree by tapping the expand button , and then locate the target group,
3. Tap the group, and then tap Enable on the Command bar. You must enable the device the same number of
Disabling and enabling time controls

Time Controls are logic devices that are created during system programming. They are configured to set up
automatic starting and stopping of system events based on time and date. The controls run in the background and
do not require any operator action. In the event you need to disable a control, you can do so from the control unit.
To disable a time control:

2. Expand the project tree by tapping the expand button , and then locate the target time control.
3. Tap the time control, and then tap Disable on the Command bar.
P/N 3102309-EN • REV 001 • ISS 18JUL19 39

To enable a time control:

2. Expand the project tree by tapping the expand button , and then locate the target time control.
3. Tap the group, and then tap Enable on the Command bar.
Changing output states

Use the On and Off commands to change the output state of relays, NAC circuit outputs, and audio amplifiers.
To activate a output state:

1. Sign in with fire privilege 3 or higher, and then tap Project Tree on the Action bar.
3. Tap the device, and then tap On on the Command bar.
To restore a relay output state:

3. Tap the device, and then tap Off on the Command bar.
Control-Display modules
Control-display modules provide additional operator interface capability.
Model [1] Description

4-24L 24 indicators
4-24L12S 24 indicators and 12 switches
The buttons on a control-display module use one of three programmed operating modes:
• Toggle: The state of the button changes each time the button is pushed (i.e. off to on or on to off).
• Interlocked: Adjacent toggle buttons operate as a group. Pushing any button in the group turns the output of
the other two buttons off and turns its own output on. An interlocked button in the on state can be turned off
without activating a second button by pressing the On button a second time. The output of the on button
remains on during control unit reset. It must be manually returned to auto when no longer required.
• Momentary: The button is on only while pressed by the operator.
40 P/N 3102309-EN • REV 001 • ISS 18JUL19

Disabling and enabling control-display modules

Disabling a control-display module isolates it from the system. While disabled, changes to the module’s state are
not processed. Enabling a control-display module re-establishes it as part of the system. When enabled, any
changes in state that occurred while the module was disabled are not processed.
To disable a control-display module:

2. Expand the project tree by tapping the expand button , and then locate the target control-display module.
3. Tap the control-display module, and then tap Disable on the Command bar.
To enable a control-display module:

2. Expand the project tree by tapping the expand button , and then locate the target control-display module.
3. Tap the control-display module, and then tap Enable on the Command bar.
Disabling and enabling control-display module elements

Disabling and enabling control-display module switches
To disable a control-display module switch:

2. Expand the project tree by tapping the expand button , and then locate the target switch.
3. Tap the switch, and then tap Disable on the Command bar.
To enable a control-display module switch:

2. Expand the project tree by tapping the expand button , and then locate the target switch.
3. Tap the switch, and then tap Enable on the Command bar.
Disabling and enabling control-display module LEDs

To disable a control-display module LED:

2. Expand the project tree by tapping the expand button , and then locate the target LED indicator.
3. Tap the LED indicator, and then tap Off on the Command bar.
To enable a control-display module LED:

3. Tap the LED indicator, and then tap On on the Command bar.
P/N 3102309-EN • REV 001 • ISS 18JUL19 41

Setting a control-display LED module mode

To set a control-display module LED mode:

3. Tap the LED indicator, and then tap one of the following: Steady, Fast Blink, Slow Blink, Off.
42 P/N 3102309-EN • REV 001 • ISS 18JUL19

Chapter 4
Preventive maintenance and
testing
Summary
This chapter provides instructions for maintaining and testing your EST4 life safety system.
Content
Introduction 44
Service provider information 44
Visual inspection schedule 45
Routine maintenance schedule 46
Troubleshooting 46
P/N 3102309-EN • REV 001 • ISS 18JUL19 43

Chapter 4: Preventive maintenance and testing
Introduction
Periodic visual inspections and maintenance testing must be performed on your EST4 life safety system to ensure
that it is operating correctly and as required by the local authority having jurisdiction (AHJ). Maintenance testing is
performed by your service provider or a qualified technician with a complete understanding of the system
hardware and functions.
Visual inspection and maintenance schedules are provided in this section, as well as a form to document your
service provider’s contact information.
Service provider information

Fill in the contact information of your service provider on the form below. If more than one service provider is
assigned, use the additional form.
EST4 Service Provider

Name
Address
City
State
Country
Postal code
Telephone
E-mail
Fax
EST4 Service Provider

Name
Address
City
State
Country
Postal code
Telephone
E-mail
Fax
44 P/N 3102309-EN • REV 001 • ISS 18JUL19

Visual inspection schedule

Perform visual inspections in accordance with Table 9 below or more often if required by the local AHJ.
Table 9: Visual inspection schedule

Component Frequency Recommended procedure
Radiant energy fire detectors Monthly Inspect the equipment for any visible signs of damage or other
changes that may adversely affect performance. Clean if necessary.
Supervisory signal devices Monthly Verify that the module’s green LED flashes. Ensure there are no
changes that may adversely affect equipment performance.
Waterflow devices Monthly Verify that the module’s green LED flashes. Ensure there are no
Batteries Semiannually Inspect batteries for corrosion or leakage. Verify that the battery
connections are tight and secure. Clean the connections, if required.
Replace batteries every 5 years, or sooner if conditions warrant.
Control unit trouble signals Semiannually Ensure there are no changes that may adversely affect equipment
performance.
Emergency voice/alarm Semiannually Inspect the equipment for any visible signs of damage or other
communication equipment changes that may adversely affect performance.
Remote annunciators Semiannually Inspect the equipment for any visible signs of damage or other
changes that may adversely affect performance.
Duct detectors Semiannually Inspect the equipment for any visible signs of damage or other
Electromechanical releasing Semiannually Ensure there are no changes that may adversely affect equipment
devices performance.
Fire extinguishing systems or Semiannually Ensure there are no changes that may adversely affect equipment
suppression systems performance.
Fire alarm boxes Semiannually Inspect the equipment for any visible signs of damage or other
Heat detectors Semiannually Inspect the equipment for any visible signs of damage or other
Smoke detectors Semiannually Inspect the equipment for any visible signs of damage or other
Interface equipment Semiannually Inspect the equipment for any visible signs of damage or other
Alarm notification appliances Semiannually Verify that the module’s green LED flashes. Ensure there are no
Supervising station life safety Semiannually Ensure there are no changes that may adversely affect equipment
system transmitters performance.
Control unit Annually Inspect the equipment for any visible signs of damage or other
Fiber optic cable connections Annually Inspect the cables for any visible signs of damage, loose connections,
or other changes that may adversely affect performance.
P/N 3102309-EN • REV 001 • ISS 18JUL19 45

Routine maintenance schedule

Routine maintenance and testing should be scheduled for your EST4 life safety system in accordance with
Table 10 below or more often if required by the local AHJ.
Note: Only your system service provider or a qualified technician with a complete understanding of the system
hardware and functions should perform system maintenance and tests.
Table 10: Routine maintenance schedule

Component Initial and Other
Reacceptance
Control equipment [1] Y Quarterly/Annually
Batteries [2] Y Annually
Control unit trouble signals Y Annually
Fiber optic cable connections Y Annually
Emergency voice/alarm communication equipment Y Annually
Remote annunciators Y Annually
Smoke detectors Y Annually
Heat detectors Y Annually
Fire alarm boxes Y Annually
Supervisory signal devices (except valve tamper switches) Y Quarterly
Waterflow devices Y Semiannually
Valve tamper switches Y Semiannually
Fire extinguishing systems or suppression systems Y Annually
Interface equipment Y Annually
Audible notification appliances Y Annually
Textual audible notification appliances (speakers) Y Annually
Visible notification appliances Y Annually
Off-premises transmission equipment Y Quarterly
Supervising station fire alarm system transmitters Y Annually
[1] Test control equipment quarterly when it is not connected to a supervising station.
[2] Replace batteries every five years, or sooner if conditions warrant.
Troubleshooting
Problems with your EST4 life safety system can generally be classified in two categories: application
programming problems and hardware (including firmware) problems. Only your system service provider or a
qualified technician with a complete understanding of system hardware and functions should perform servicing
and repairs. Refer to “Service provider information” on page 44 for their contact information.
Before contacting your service provider, make note of the following:
• Messages shown on the LCD screen
• Construction in the area that may have caused the problem
• Adverse weather that may have caused the problem
• Damage to any equipment
46 P/N 3102309-EN • REV 001 • ISS 18JUL19

Appendix A
System addressing
Summary
This appendix provides a list of logical addresses for system modules and devices.
Content
Address format 48
Module addresses 48
LRM device addresses 51
Control-display device addresses 51
P/N 3102309-EN • REV 001 • ISS 18JUL19 47

Appendix A: System addressing
Address format
EST4 addresses are in NNNCCCDDDD format, where:
• NNN is the node number. The node number is assigned when the installer downloads the CU database into
the control unit.
• CCC is the local rail module slot address. The node number and LRM slot address make up the LRM’s logical
address.
• DDDD is the device’s point address. The node number, LRM logical address, and LRM device point address
make up the device or circuit’s logical address.
Module addresses
Modules have a physical address and a logical address. The physical address identifies the card’s location in the
panel. The logical address identifies the card in the CPU database.
For a control unit with one node, see Figure 13 and Table 11 on page 49.
For a control unit with multiple nodes, see Figure 14 and Table 12 on page 50
48 P/N 3102309-EN • REV 001 • ISS 18JUL19

Figure 13: Logical addressing for control unit with one node (4-CAB21DL inner door/4-CAB21B backbox shown)
064 066 067 068 069 070 071
000 001 002 003 004 005
072 073 074 075 076 077 078 079
006 007 008 009 010 011 012
080 081 082 083 084 084 086 087
013 014 015 016 017 018 019
Table 11: Logical addressing for a control unit with one node
Card Logical address
Operator layer modules on the inner door frame assembly
4-LCD NNN064(065)
Control-display modules NNN066 to NNN087
Hardware LRMs on the 3-CHAS7 chassis
4-CPU NNN000
Local rail modules NNN001 to NNN019
P/N 3102309-EN • REV 001 • ISS 18JUL19 49

Figure 14: Logical addressing for control unit with multiple nodes (4-CAB21DL inner door/4-CAB21B backbox shown)
064 066 067 068 069 070 071
000 001 002 003 004 005
064 066 068 070 071
006 007 010 011 012
072 073 074 075 076 077 078 079
013 014 015 016 017 018 019
Table 12: Logical addressing for a control unit with multiple nodes
Card Logical address
Operator layer modules on the inner door frame assembly
4-LCD NNN064(065)
4-LCDANN NNN064(065) [1]
4-FT NNN066(067) [2][4]
4-MIC NNN068(069) [3]
Hardware LRMs on the 3-CHAS7 chassis
4-CPU NNN000
Local rail modules NNN001 to NNN007 [4]
Local rail modules NNN010 to NNN019
[1] Logical addressing restarts with NNN064 when the 4-LCDx is connected to the CPU node module.
[2] The logical address for a 4-FT firefighter telephone is always NNN066.
[3] The logical address for a 4-MIC paging microphone is always NNN068.
[4] Local rail modules cannot be installed on the 3-CHAS rail behind a 4-FT firefighter telephone.
50 P/N 3102309-EN • REV 001 • ISS 18JUL19

LRM device addresses

Table 13 below lists the device addresses for points for LRMs installed on the chassis rail.
Table 13: LRM device point addresses

Card Device or circuit Address
3-IDC8/4 IDC/NAC 1 NNNCCC0001
IDC/NAC 2 NNNCCC0002
IDC 3 NNNCCC0003
IDC 4 NNNCCC0004
IDC 7 NNNCCC0007
IDC 8 NNNCCC0008
3-SSDC1 Detectors NNNCCC0001 to NNNCCC0125
Modules NNNCCC0126 to NNNCCC0250
3-SDDC1
Loop 1 Detectors NNNCCC0001 to NNNCCC0125
Loop 2 Detectors NNNCCC0251 to NNNCCC0375
3-ZA20(A/B) Amplifier output NNNCCC0000
24V DC output NNNCCC0001
3-ZA40(A/B) Amplifier output NNNCCC0000
3-ZA95 Amplifier output NNNCCC0000
Control-display device addresses

The tables in this section list switch and indicator addresses that the system assigns to operator layer control-
display modules.
• EST4 system control-display modules LED and switch numbering see Table 14 on page 52
• EST3 migrated system control-display modules LED and switch numbering see Table 15 on page 53
P/N 3102309-EN • REV 001 • ISS 18JUL19 51

Figure 15: EST4 operator layer control-display modules
4-24L 4-24L12S 4-24L18S 4-24L24S
Table 14: EST4 operator layer control-display addresses

Module type Switch group Switch address Indicator address
4-24L N/A N/A 0129 to 0152
4-24L12S 1 0002 0129 to 0130
2 0004 0131 to 0132
3 0006 0133 to 0134
4 0008 0135 to 0136
5 0010 0137 to 0138
6 0012 0139 to 0140
7 0014 0141 to 0142
8 0016 0143 to 0144
9 0018 0145 to 0146
10 0020 0147 to 0148
11 0022 0149 to 0150
12 0024 0151 to 0152
4-24L18S 1 0001 0129
2 0002 0130
3 0003 0131
– – 0132
4 0005 0133
5 0006 0134
6 0007 0135
– – 0136
52 P/N 3102309-EN • REV 001 • ISS 18JUL19


7 0009 0137
8 0010 0138
9 0011 0139
– – 0140
10 0013 0141
11 0014 0142
12 0015 0143
0144
13 0017 0145
14 0018 0146
15 0019 0147
– – 0148
16 0021 0149
17 0022 0150
18 0023 0151
– – 0152
4-24L24S 1 to 24 0001 to 0024 0129 to 0152
Figure 16: EST3 control-display LED and switch numbering
3-24G, 3-24R 3-12SG,3-12/SR, 3-12/S1GY, 3-12/S1RY,

3-24Y, 3-12RY 3-12SY 3-12/S2Y 3-4/3SGYWR
Table 15: EST3 operator layer control-display addresses

3-24G, 3-24R, 3-24Y, 3-12RY N/A N/A 0129 to 0152
P/N 3102309-EN • REV 001 • ISS 18JUL19 53


3-12SG, 3-12SR, 3-12SY 1 0001 0129
2 0002 0130
3 0003 0131
4 0004 0132
5 0005 0133
6 0006 0134
7 0007 0135
8 0008 0136
9 0009 0137
10 0010 0138
11 0011 0139
12 0012 0140
3-12/S1GY, 3-12/S1RY, 1 0001 0129
3-12/S2Y 0130
2 0002 0131
0132
3 0003 0133
0134
4 0004 0135
0136
5 0005 0137
0138
6 0006 0139
0140
7 0007 0141
0142
8 0008 0143
0144
9 0009 0145
0146
10 0010 0147
0148
11 0011 0149
0150
12 0012 0151
0152
3-6/3S1G2Y, 3-6/3S1GYR, 1 0001 0129
3-6/3SGYWR 0002 0130
0003 0131
2 0004 0132
0005 0133
0006 0134
3 0007 0135
0008 0136
0009 0137
4 0010 0138
0011 0139
0012 0140
54 P/N 3102309-EN • REV 001 • ISS 18JUL19


5 0013 0141
0014 0142
0015 0143
6 0016 0144
0017 0145
0018 0146
3-4/3SGYWR 1 0001 0129
0002 0130
0131
0003 0132
2 0004 0133
0005 0134
0135
0006 0136
3 0007 0137
0008 0138
0139
0009 0140
4 0010 0141
0011 0142
0143
0012 0144
P/N 3102309-EN • REV 001 • ISS 18JUL19 55

56 P/N 3102309-EN • REV 001 • ISS 18JUL19

Glossary
Term Definition
active Points that are in an alarm state.
activate To turn on or energize. Pertains to outputs (including logical outputs).
AHJ Authority Having Jurisdiction
alarm The state of a fire alarm initiating device that has detected a smoke or fire condition.
card See module.
Central Control Station Terminology used to identify a command center that may or may not reside in a
notification control area, but it can control audio over its own or multiple NCAs.
CMS Central Monitoring Station
Command Center Command centers are used to control audio within a Notification Control Area (NCA). The
command center resides in a notification control area and it is the control unit used to
request, grant, or deny control of the audio operation of an NCA, whether the one in
which it resides or another NCA when the command center is a central control station.
CU Configuration Utility. 4-CU software lets programmers configure and program an EST4
control unit.
database User-defined, permanently stored, system parameters containing system definitions,
device types, responses, messages, etc.
device Circuits, buttons, or LEDs that exist on the chassis rail or UI frame assembly and all
addressable devices connected by field wiring.
disable Prevents an input, output, or system feature from functioning.
enable Permits an input, output, or system feature to function.
EVAC Emergency Voice/Alarm Communications
group A collection of Signature devices that is treated as a single entity for programming
purposes.
input A signal generated by a field device and sent to the control unit for evaluation and
responses as determined by the system database. Inputs to the system are detectors,
modules, and switches.
label A unique identifier for a device.
loop The wiring that connects devices to the fire alarm control unit.
module Modules (cards) installed on the backbox chassis rail and control-display modules
installed on the inner door UI frame assembly.
NCA See Notification Control Area.
normal state The system is in a quiet state. The LCD screen shows no event messages.
node A control unit used to monitor system inputs for status changes and activate system
outputs.
P/N 3102309-EN • REV 001 • ISS 18JUL19 57

Glossary
notification control areas Grouped nodes installed throughout the premises that provide a structure for the
distributed audio system and are used to define the audio subsystem's coverage area.
A basic NCA has one or more command centers for controlling the operations of the
members of the NCA. In some installations multiple NCAs can be managed by one or
more central control stations.
off-normal state The system enters the fire alarm, trouble, disabled, or test state. The LCD screen shows
event messages and system LEDs indicate off-normal statuses.
output A signal generated by the system, based upon responses defined in the system
database, and sent to external field devices. Outputs are LEDs, and modules.
point See device.
pseudo point An input or output point that is not a physical device. For example, ground fault and
communication fault notifications.
Request Grant Deny A programming logic device that works in association with NCAs and command centers
to arbitrate demands for control of audio communications in the life safety system.
reset An active condition or command used to force an output to its OFF condition. An output’s
OFF state may be in the restored condition (normal) or reset condition.
restore A condition of an input, where the input is not active. It also refers to the condition of an
output where the output is not in its set or reset condition and does not have a priority
value associated with it.
RGD See Request Grant Deny.
riser An electrical path that contains power or a signal that is used by multiple outputs, zones,
or circuits.
signaling line circuit The wiring that connects devices to the fire alarm control unit.
time control An input activated by the time of day or day of the month.
58 P/N 3102309-EN • REV 001 • ISS 18JUL19

Index
A C
access code, 26 change
Acknowledge button, 19 alarm sensitivity threshold, 36
acknowledge events, 19 output state, 40
Action bar, 5, 7 screen language, 21
buttons, 5, 12 chassis rail
activate addressing, 49, 50
alternate alarm sensitivity, 36 Command bar, 13
addresses buttons, 7
3-CHAS rail, 49, 50 control-display module
device circuits, 51 buttons, 40
EST3 control-display indicators, 53 disabling button, 41
EST3 control-display switches, 53 disabling LED, 41
EST4 control-display indicators, 52 disabling module, 41
EST4 control-display switches, 52 enabling button, 41
format, 48 enabling LED, 41
hardware layer, 49, 50 enabling module, 41
LRM points, 51 indicator addresses for 4-24 series modules, 52
modules, 48 indicator addresses for EST3 modules, 53
operator layer, multiple node, 50 models, 40
operator layer, one node, 49 operating modes, 40
UI rail, 49, 50 switch addresses for 4-24 series modules, 52
alarm history count, 22, 25 switch addresses for EST3 series modules, 53
Alarm LED, 3 CPU Fail LED, 3
alarm sensitivity threshold, 36
Alarm Silence button and LED, 5 D
alternate alarm sensitivity, 36
date
AND group
LCD screen, 5
disable, 39
setting, 37
enable, 39
deny control
announcements
control display module, 28
firefighter telephone, 31
LCD user interface, 27
microphone, 29
device
answer call, 32
circuit addresses, 51
archive setting, 26
disable, 38
drill, 23
B
enable, 38
buttons maintenance report, 24
LCD screen, 7 message, 7
buzzer. See operator alert signal view details, 21
P/N 3102309-EN • REV 001 • ISS 18JUL19 59

Index
disable firmware version (continued)

AND group, 39 LRM, 25
control-display module, 41 freeze events history, 36
control-display module button, 41
control-display module LED, 41 G
devices, 38
grant control
Instruction Text group, 39
control display module, 28
LRMs, 38
LCD user interface, 27
Matrix group, 39
groups, 39
Service group, 39
Zone group, 39
H
disconnect call, 33
drill history
performing, 23 freeze, 36
Drill button and LED, 4 History reports
History, 24
E History Alarm, 24
History Supervision, 24
enable
History Trouble, 24
AND group, 39
control-display module, 41
I
control-display module button, 41
control-display module LED, 41 icons, 7
device, 38 Instruction Text
Instruction Text group, 39 disabling group, 39
LRMs, 38 enabling group, 39
Matrix group, 39 view details, 20
Service group, 39
Zone group, 39 L
Event Details buttons, 7 lamp test, 22
event indicator, 7 LCD screen, 3
event lists buttons, 7
viewing, 19 date, 5
event message icons, 7
list, 9 language, 21
Local mode, 9 normal, 5
number, 7 off-normal, 5
Proprietary mode, 9 option buttons, 7
screen, 5 time, 5
type, 7 List bar, 7
event type buttons, 11
priority, 8 lists, 7, 9
to queue, 8 local rail module. See LRM
lock
F remote write, 26
fire privilege logic groups, 39
levels, 10 view details, 20
firefighter telephone logical addressing. See addresses
announcements, 31 LRM
answer call, 32 point addresses, 51
disconnect call, 33
two-way communication, 32 M
firmware version, 25 maintenance
annunciator, 25 device reports, 24
CPU, 25 preventive, 44
60 P/N 3102309-EN • REV 001 • ISS 18JUL19

Index
maintenance (continued) reports (continued)

routine, 46 Status, 22
schedules, 44 Status Disabled, 22
service provider, 44 Status Test, 22
visual inspection schedule, 45 System Info, 26
market setting, 25 request control
mass notification signal control display module, 28
signaling, 31 LCD user interface, 27
silence signal, 31 Request Grant Deny. See RGD
Matrix group Reset button and LED, 5
disable, 39 reset the system, 23
enable, 39 restore primary alarm sensitivity, 37
microphone Revision report
announcements, 29 Alarm history count, 22, 25
MNS signaling, 30 Annunciator, 25
MNS Configuration messaging, 25
microphone announcement, 30 Configuration schema, 25
signaling, 31 Configuration time stamp, 25
silence signal, 31 Configuration version, 25
CPU, 25
O Firmware, 25
LRM, 25
off-normal, 5
Market, 25
operator alert signal
RGD, 27
pattern, 8
deny control using control display module, 28
silencing an alarm, 18
deny control using LCD, 27
silencing the panel, 18
grant control using control display module, 28
operator controls
grant control using LCD, 27
interface buttons, 2
request control using control display module, 28
interface indicators, 2
request control using LCD, 27
LCD screen, 7
option buttons, 7
S
output
changing states, 40 schedule
routine maintenance, 46
P scroll bars and buttons, 7
Service group
Panel Silence button and LED, 3
disable, 39
Power LED, 3
enable, 39
primary alarm sensitivity, 36
service provider, 44
print
silence
device maintenance reports, 24
alarm signals, 18
Print screen button, 7
operator alert signal, 18
project number, 25
software version, 26
project version, 26
Status Disabled report, 22
Q Status reports
Status, 22
queues, 7, 9 Status Disabled, 22
Status Test, 22
R Status Test report, 22
Remote Write Unlock, 26 system
reports addressing, 48
device maintenance, 24 enabling time controls, 39
History, 24 off-normal screen, 5
Revision, 22, 25 resetting, 23
service provider, 44
P/N 3102309-EN • REV 001 • ISS 18JUL19 61

Index
system (continued) Z
setting the date, 37
zone
setting the time, 37
disabling group, 39
System Info report
enabling group, 39
Licensing, 26
Project Description, 26
Versions, 26
T
telephone
announcements, 31
answer call, 32
disconnect call, 33
two-way communication, 32
test
lamp, 22
LCD and LEDs, 22
time
LCD screen, 5
setting, 37
time controls, 39
time stamp, 25
touch screen display, 3
Trouble LED, 3
troubleshooting, 46
U
unlock
remote write, 26
user
command controls, 2
fire privilege levels, 10
indicators, 2
interface, 2
V
view
alarm history count, 22
event list, 19
history reports, 24
status reports, 22
view event details
device details, 21
from event list, 21
from project tree, 21
instruction text details, 20
logic group details, 20
W
web service
block access, 36
unblock access, 36
62 P/N 3102309-EN • REV 001 • ISS 18JUL19

3102309-En r001 Est4 User Guide

Uploaded by

Document Informationclick to expand document information

Copyright:

Available Formats

3102309-En r001 Est4 User Guide

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

3102309-En r001 Est4 User Guide

Uploaded by

Copyright:

Available Formats

EST4 User Guide

P/N 3102309-EN • REV 001 • ISS 18JUL19

Important information iii

Chapter 2 Basic operating instructions 17

Chapter 3 Advanced operating instructions 35

Chapter 4 Preventive maintenance and testing 43

Appendix A System addressing 47

P/N 3102309-EN • REV 001 • ISS 18JUL19 i

ii P/N 3102309-EN • REV 001 • ISS 18JUL19

EST4 FCC compliance

P/N 3102309-EN • REV 001 • ISS 18JUL19 iii

iv P/N 3102309-EN • REV 001 • ISS 18JUL19

3-MODCOM(P) Industry Canada information

Life safety system limitations

P/N 3102309-EN • REV 001 • ISS 18JUL19 v

P/N 3102309-EN • REV 001 • ISS 18JUL19 1

EST4 LCD user interface

Figure 1: LCD user interface (4-LCD shown)

(1) (2) (3) (4)

ALARM TROUBLE CPU FAIL POWER ON

PANEL SILENCE (6)

Command controls and indicators

2 P/N 3102309-EN • REV 001 • ISS 18JUL19

Table 1: User interface command controls and indicators descriptions

P/N 3102309-EN • REV 001 • ISS 18JUL19 3

No. Control/Indicator Description

4 P/N 3102309-EN • REV 001 • ISS 18JUL19

No. Control/Indicator Description

LCD screen indications

P/N 3102309-EN • REV 001 • ISS 18JUL19 5

Figure 2: System normal and off-normal screens

08/21/2018 12:07:33 Alarm 3 Other 3 08/21/2018 12:07:33

System Project Sign System Project Sign

System normal screen System off-normal screen

6 P/N 3102309-EN • REV 001 • ISS 18JUL19

LCD screen operator controls

Figure 3: LCD screen operator controls

(1) Command bar with left and right scroll buttons

Status History Revision

System Project Sign Holidays

LCD screen operator interface icons and option buttons

Table 2: Operator interface icon and option button descriptions

⟳ Reports option button. Tap to refresh

🠔🠔 Reports option button. Tap to go to

🠖🠖 • Reports option button. Tap to go to

P/N 3102309-EN • REV 001 • ISS 18JUL19 7

Icon Description Icon Description

⎙ Printer option button. Tap to send

⚲ Details option button. Tap to access an

√ Appears next to acknowledged events

Keypad delete button. Tap to delete a ▶ 3X Future feature

☓ User administration button. Tap to

✎ Users administration button. Tap to

Event indicator queues

Table 3: Event queues and properties

8 P/N 3102309-EN • REV 001 • ISS 18JUL19

Event message lists

Figure 4: Event message

Alarm 3 Other 3 08/21/2018 12:07:33