Extension Cord Checklist

Inspection Checklist - Power and Extension Cords
Company Name:
Safety Officer Name:
Project Engineer Name:
Remarks
DATE: INSPECTORS: Yes No
Power cords and extension cords being used are the proper
type and size for the task. Specific cords approved for wet
locations are used when necessary.
All extension cords are grounded cords, with the
grounding pin intact.
All power cords and extension cords are in good repair,
without damage to the outer jacket insulation, plugs, or
pins.
Inline or built-in GFCI devices are used when cords are
used in wet locations or during construction activities.
Extension cords are used for temporary purposes only, and
not as a replacement for permanent building wiring.
Extension cords are not zip-tied or otherwise connected to
existing conduit or other building features.
Power cords and extension cords are not run through
doorways, windows, or unprotected openings or holes in
walls.
Power cords and extension cords are run so that they do
not create tripping hazards.
All equipment with damaged cords have been removed
from service.
Any repairs to power cords or extension cords have been
made by a qualified person, and the repairs have the same
or greater protective qualities as the original cord or plug.
Revised 01/26/16
Power Cord and Extension Cord Guidance
While cordless power tools are quickly replacing corded tools in the workplace, there are still many situations that require
the use of a corded tool or electrical extension cord. Used properly, these tools make the job quicker and easier, but used
improperly, electrical cords can be very dangerous. The key to keeping employees safe when using electrical cords is to
ensure the proper cords are selected and used, and that they are kept in good condition. The guidelines below represent the
minimum requirements for flammable storage.
Tool and Equipment Power Cord - Flexible power cords are used to minimize the likely hood of damage or wear from
repeated movement or vibration of the equipment it’s attached to, or when a tool or piece of equipment needs to be
portable. Tools are typically designed with power cords that will safely handle the amount of current the tool requires
without heating or shorting. When using a tool or piece of equipment with a power cord, make sure that the power source is
properly rated for the tool or equipment to be used.
A power cord will be made of two or more inner conductive wires with rubberized insulation around each wire, covered by
an outer casing or jacket of rubberized plastic that protects the inner insulation. Depending of the type of equipment, the
cord may or may not have a ground conductor. Hand-held tools that are manufactured with non-metallic cases are called
“double- insulated”. If approved by nationally recognized testing laboratory (NRTL) such as Underwriter’s Laboratory (UL
Approved), they do not require grounding under the National Electrical Code. Although this design method reduces the risk
of grounding deficiencies, a shock hazard can still exist. Other equipment that has metal as part of its housing is required to
have a ground wire and grounding pin on the plug of the cord. This grounding pin cannot be removed, and a 3-to-1 plug
adaptor cannot be used with the equipment.
Extension Cords - These cords, also called “temporary flexible cables”, are used when power is needed at a location that
does not have an outlet within reach of a tool’s or light’s power cord. The key word to remember about extension cords is
“temporary”. These cords are to be used for temporary purposes such as maintenance or repair work, or during construction
activities. These cords are not designed or allowed to be used as permanent wiring. In workplace settings, all extension cords
must be grounding cords. This means that they have to have a power (or Hot) wire, a neutral wire, and a ground wire.
Usually the power wire is black, the neutral wire is white, and the ground wire is green, but this might not be the case in all
pieces of equipment.
Care should be given when using extension cords so that the cords do not create tripping hazards. Extension cords should
not be run across walkways or aisle ways where they could cause a hazard or where they could be damaged by vehicles or
material handling equipment such as forklifts.
Both power cords and extension cords should be free of any visible damage including:
 cut or torn outer insulation jacket or inner insulation,
 dry rot,
 cracked, or worn outer insulation jackets,
 exposed inner insulation,
 outer jacket pulled from the cord end,
 missing ground pin,
 Spring-liked or coiled appearance (caused by repeated overheating of the conductors)
If repairs become necessary on equipment power cords or extension cords, the repaired cord must have the same protective
rating as the original cord. This means that an “electrical tape repair” is not allowed since it does not provide the same level
of protection as the original out jacket insulation. If a power cord’s outer jacket is compromised, the tool should be removed
from service and the entire cord should be replaced. If the rubber strain relief provided where the cord enters the tool
becomes damaged or is missing, the tools should be removed from service until the strain relief can be replaced. If the plug
of a cord becomes damaged, either by having the outer jacket insulation pulled out of the plug, or the grounding pin is loose
or missing, the tool should be taken out of service until the plug can be replaced. Any repairs to power cords should be done
by a competent person that has been trained on how to select the correct replacement parts and how to properly install
them.
Revised 01/26/16

Extension Cord Checklist

Uploaded by

Copyright:

Available Formats

Extension Cord Checklist

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Extension Cord Checklist

Uploaded by

Copyright:

Available Formats

Inspection Checklist - Power and Extension Cords

Safety Officer Name:

Project Engineer Name:

You might also like