Ccna3 CS
Ccna3 CS
Ccna3 CS
Cisco Networking Academy Program CCNA 3: Switching Basics and Intermediate Routing v3.0
Use the resources provided (diagram and narrative) to set up the physical network. Set up an IP subnetting scheme using Variable Length Subnet Masking (VLSM) Configure the routers as required Set up and configure the switches and VLANs as required Verify and troubleshoot all connections Provide detailed documentation in the appropriate format Provide a written final report.
1-2
Scenario
The XYZ Research Company is a small company that develops high-speed wireless products. The main office occupies two buildings in Sydney; one building is for the Administration Group, and the other building is for the Sales and Marketing Group and the larger Research and Development Group. The Research Group and the Sales and Marketing Group will each have employees on all three floors of the main building. The XYZ Research Company also has a Sales office located in Melbourne. The company is implementing a wired network that should support 100% growth over the next 5 to 10 years. A logical diagram of the network is provided. Your task is to design, implement, and fully document the XYZ Research Company network. In addition to a formal report, the XYZ Research Company would like to see a prototype of the network before it is fully implemented, to verify that it will meet the companys needs.
Phase 1: Requirements
Sample logical diagram
1-4
Requirements
The preceding figure depicts the XYZ Research Companys partially completed, logical diagram of the required network. The company has also provided networking equipment for development and demonstration. In some instances, the equipment it provides does not have the required LAN interfaces. In this case, the company allows configuration of loopback networks as alternatives.
18 employees in the Research and Development group Nine employees in the Sales and Marketing group Seven employees in the Administration group Five employees in the remote sales office Lifetime maximum of five servers on a separate subnet, regardless of company growth Use subnet 200.200.100.0/30 for connection to the Internet router Use public class C network 223.0.0.0 for internal addressing Use VLSM for IP addressing Expect 100% growth of current IP requirements when determining the size of subnets All networking devices must have IP addresses
Worksheet
1. Produce a logical diagram that includes:
Router and switch names Router interface details Network addresses The number of hosts per network Clearly indicate DCE serial interfaces Link Speeds
2. The company expects the use of VLSM design to maximize the use of IP addresses. A table is produced showing all possible subnets that meet the companys requirements using a VLSM design. Subnets that will not be used are to be clearly identified in the table.
The following is a sample table layout for recording the VLSM design.
Number of Host Addresses Required Network Address Subnet Mask Max Number of Hosts Possible In Use (Yes/No) Network Name
3. For each location, including the Internet, an additional set of tables is required.
These tables assist with design and development activities and are used when configuring switches and routers. A separate table should be created for each router and switch at each location. (NOTE: Some fields in the switch table will be completed in Scenario (part 4).)
Following is a sample layout for routers. Location: ____________________ Router Name: ____________________
Interface or /Sub interface type/number Descriptio n and Purpose DCE/DTE (if applicable) Speed or Clock Rate Network Name Network Number Interface IP Address Subnet Mask
1-6
Following is the sample layout for the switch tables. Location: ____________________ Switch Name: ____________________ Switch IP address: ____________________
Interface or /Sub interface type/port/number Description and Purpose Speed Duplex Network Name Network Number Subnet Mask VLAN Switchport Type Encapsulation (if needed)
Location: ____________________
Copyright 2003, Cisco Systems, Inc. Case Study: Access Control Lists (ACLs) 1-7
4. To complete the IP design, assign and tabulate PC/workstation and server addresses for each LAN in each location. A DHCP server assigns PC workstation addresses. Server addresses are assigned statically.
1-8
For the demonstration, the company agrees that it is enough to statically assign all PC workstation and server addresses. Following is a table to collect documentation to deliver to the XYX Company:
LAN name
T h e t a b l e s
PC or Server Name
IP Address
Subnet Mask
Gateway
Services Provided
The tables and supporting text are part of the documentation you will delivere to the XYZ Research Company. Before you begin the next task, you must have your logical diagram and tables approved by the company. Instructors Signature: ______________________Date:_______________
1-10
Phase 3: OSPF
The company has decided to use OSPF as the routing protocol. XYZ Research Company Requirements
OSPF process ID of 50 All routers in a single area: area 0 Loopback address assigned to each router Loopback address used as the OSPF router ID There is one multi-access network in the administration building, so a DR must be elected Determine whether to use the router ID or interface priority to determine the DR in the administration building
Worksheet 1. Update the IP address tables produced previously to include the loopback addresses. 2. Make a decision about which router and router interface will be the DR. The group discusses these issues, records the major points of the discussion, documents them, and makes recommendations. Explain your reasons for choosing the router ID or interface priority to determine DR. Explain your reasons for choosing router _______________ as DR in the administration building. 3. Will a DR be elected on the serial connections between buildings and the remote branch office? ________ Why? ______________________ Update the diagram with OSPF information. The location tables, router, IP address table, and diagram are modified to include this information and are presented to the company. Instructors Signature: _______________________Date:_______________
Phase 4: VLANs
Now the company wants information about VLANs, which are required in the main building. The company has provided the following information: XYZ Research Company Requirements
There are 18 Research and Development employees There are nine Sales and Marketing employees Eight Research personnel and two Sales personnel are on Floor 3 Six Research personnel and four Sales personnel are on Floor 2 Four Research personnel and three Sales personnel are on Floor 1 Floor 1 also has the Server LAN. Five server machines are planned, but only one is available at this time. There are separate rooms on each floor for the workgroups There is sufficient space in each room to accommodate growth The 100% predicted growth will occur uniformly per floor Switches in the main building are connected in a loop such that if one switch fails, an alternative path is used There is one switch per floor, shared among the different subnets Spanning tree root is to be placed in an optimal position
Worksheet 1. Tables documenting Switch VLAN port assignments are produced for the available demonstration equipment. Unassigned ports are to remain in the default VLAN. The following table is an example of the documentation required by the company. Switch Details
Switch Name Model # of Ports Location IP Address Gateway Management VLAN VTP Mode VTP Domain STP Root
1-12
VLAN Port Assignments Update the switch tables, located in the worksheets of Scenario (part 2), to include the VLAN and port information for each server, workstation, the interconnect between switches, and the inter-connect to the router in the main building. 2. Before submitting the documentation, you must justify your decision about the STP
root bridge. Write one paragraph justifying your choice.
Following is a diagram from the companys old site to help with the physical layer design.
1-14
The company requires a similar diagram for the main building. The main building has three floors and will use CAT 5 throughout for the LANs. The diagram should include the following:
The length and number of cable runs The labeling convention for each of the outlets and patch panel. Generic room names and port names, such as IDFFloor 1, Floor1Room1Port1. HCC1:Floor1Room1Port1 ,and VCC1:Floor1XFloor2Port1, are acceptable. Use any standards that apply in the region.
The horizontal cable runs on each floor will be no more than 30 meters. The length of cable needed between consecutive floors is 15 meters. The documentation should include a description of how cross connects for all trunks will be patched for the required logical topology. List the pinout (straight or crossover) cable types. Instructors Signature:_________________________Date:_______________
2. Demonstrate access of all hosts to each other and HTTP service on the server machine.
From Host To Host Pass/Fail
3. Demonstrate the behavior of the inter-network when a single trunk link fails.
From Host To Host Trunk Up/Down Route Pass/Fail
1-16
Recommendation 2:
Instructors Signature:_________________________Date:_______________
Instructors Signature:_________________________Date:_______________
1-18
Phase 8: Presentation
Your final task in this case study is to deliver a 10-minute presentation of the main features of the design decisions and your recommendations. Also provide a formal written report that contains all the design documents as well as all the supporting worksheets (see Case Study Deliverables section). The document should be complete enough to allow a third party to install and configure the network without any additional
Instructors Signature:_________________________Date:_______________
Outline Summary of the company and network requirements Discussion of the implementation of IP address and VLSM Discussion of the implementation of routing Discussion of the implementation of VLANs, STP, and switches Discussion of the physical layer design and equipment Discussion of testing and verification strategies Output of testing and verification commands from routers Output of testing and verification commands for switches Recommendations for future network upgrades Logical diagram Physical diagram IP addressing table Router interface table Switch table PC addressing table Routing protocol matrix Equipment table Router configurations (printed and floppy) Switch configurations (printed and floppy) Testing results (printed and floppy)
1-20