MODEL: SI-100

(Fixed Gas Detector)

Manual
SI-100 MANUAL

WARNING
Read this manual carefully before using the instrument. The instrument
will perform as designed only if it is used and maintained in accordance
with the manufacturer's instruction. Otherwise, it could fail to perform as
designed and persons who rely on this instrument for their safety could
sustain serious personal injury or death.

Warning

➢ Remove any debris on the surfaces of the sensor part before use.
➢ Test regularly whether the alarms go off properly.
➢ Use the device under the conditions instructed, including the temperature, humidity and
pressure range. The use out of the instructed conditions may cause malfunction or failure.
➢ The sensors inside the device may indicate the gas concentration differently according to the
environment such as temperature, pressure and humidity. Make sure to calibrate the detector
under the same or similar environment to the specification.
➢ Severe shock to the device may cause failures of the device or sensors.
➢ Alarm values are set according to international standards. Therefore, the values must be changed
by an authorized expert.

Caution

➢ Use the device after reading this manual thoroughly.

➢ This product is not a gas analyzer, but a gas detector.
➢ If calibration failure occurs continuously, stop using the equipment and contact the manufacturer.

Warranty

We, SENKO CO., LTD warrant replacement or repair for the products of SI series for 24 months from the
shipment date of the product(s). However, the parts, whose life can be shortened by use, such as sensors,
batteries and lamps are not under the warranty. Also, Free repair and replacement is not available in case of
purchases of our products through unauthorized channels, mechanical damage and deformation by user’s
misuse, and calibration and replacements of parts without following the instruction in the manual. If any defect
or quality problem occurs to the products during the warranty period, the user should notify it to the
manufacturer. In this case, all the expenses except freight cost are paid by SENKO. Repair, replacement and
freight cost for the products, whose warranty is already over, are paid by the user. SENKO CO., LTD does not
have any responsibility for indirect, or accidental loss which occurs while using our products, and the warranty
is limited to the exchange of parts and products. The warranty is subject to the users who have bought
products from the authorized agency and office appointed by SENKO CO., LTD, and warranty repairs must be
made through the designated A/S center of SENKO CO., LTD with a skilled technician.

2
SI-100 MANUAL

Table of Contents
1. Introduction ................................................................................................................................................................. 4

1.1. Specification ................................................................................................................................................... 4

1.2. Sensor List ....................................................................................................................................................... 5

2. Instrument Overview............................................................................................................................................... 6

3. How to install ............................................................................................................................................................. 7

3.1. How to fix ........................................................................................................................................................ 7

3.2. How to open and wire .............................................................................................................................. 7

3.2.1 Separating Cover from Gas Detector Body ................................................................................ 7

3.2.2 Gas Detector Wiring Diagram ........................................................................................................... 7

4. Measuring Mode ....................................................................................................................................................... 8

4.1. Gas Detector Initial Operation ............................................................................................................... 8

4.1.1 Initial Screen Explanation .................................................................................................................. 10

4.2. Set Display ..................................................................................................................................................... 10

4.2.1 Description of Set Display ................................................................................................................. 10

4.3. Advanced setting ....................................................................................................................................... 11

4.4. How to modify the settings [Flow chart] ...................................................................................... 12

4.5. Zero calibration & Span calibration.................................................................................................. 13

4.5.1 How to connect Calibration cap .................................................................................................... 13

4.5.2 Calibration Mode Explanation ......................................................................................................... 13

4.5.3 How to enter Calibration Mode ..................................................................................................... 14

5. Certificate ................................................................................................................................................................... 15

3
SI-100 MANUAL

1. Introduction

1.1. Specification
✓ Various sensors can be applied

✓ Easy operation with a magnetic bar

✓ Large digital LCD embedding white backlight

✓ Explosion-proof & Water/Dust-proof structure

✓ Automatic calibration function

✓ Long-distance transmission by 4-20mA output

4
SI-100 MANUAL

1.2. Sensor List

Gas Sensor Range A1 A2 Resolution

Oxygen O2 Electrochemical 0~30%Vol 19.0%vol 23.0%vol 0.1%vol

Carbon Monoxide CO Electrochemical 0~500ppm 30ppm 60ppm 1ppm

Sulfur Dioxide SO2 Electrochemical 0~20ppm 2ppm 5ppm 0.1ppm

Hydrogen H2 Catalytic 0~100%LEL 15%LEL 50%LEL 1%LEL

Hydrogen H2 Electrochemical 0~1000ppm 100ppm 500ppm within 5ppm

Hydrogen Sulfide H2S Electrochemical 0~500ppm 10ppm 15ppm 1ppm

Combustible - Catalytic 0~100%LEL 15%LEL 50%LEL 1%LEL

Combustible - IR 0~100%LEL 15%LEL 50%LEL 1%LEL

Ammonia NH3 Electrochemical 0~100ppm 25ppm 35ppm 1ppm

Acetylene C2H2 Catalytic 0~100%LEL 15%LEL 50%LEL 1%LEL

Ethanol C2H6O Catalytic 0~100%LEL 15%LEL 50%LEL 1%LEL

Toluene C7H8 IR 0~100%LEL 15%LEL 50%LEL 1%LEL

Toluene C7H8 Catalytic 0~100%LEL 15%LEL 50%LEL 1%LEL

Methane CH4 IR 0~100%LEL 15%LEL 50%LEL 1%LEL

Methane CH4 Catalytic 0~100%LEL 15%LEL 50%LEL 1%LEL

Chlorine Cl2 Electrochemical 0~5ppm 0.5ppm 1.0ppm 0.1ppm

Chlorine Cl2 Electrochemical 0~20ppm 0.5ppm 1.0ppm 0.1ppm

Carbon Dioxide CO2 IR 0~2000ppm 1000ppm 1500ppm 3ppm

Carbon Dioxide CO2 IR 0~5000ppm 3000ppm 5000ppm 8ppm

Carbon Dioxide CO2 IR 0~5%Vol 0.5%vol 3%vol 0.1%vol

Hydrogen Chloride HCl Electrochemical 0~10ppm 1ppm 2ppm 0.1ppm

VOC VOC PID 0~1000ppm 50ppm 100ppm within 3ppm

Xylene C8H10 IR 0~100%LEL 15%LEL 50%LEL 1%LEL

Hydrogen peroxide H2O2 Electrochemical 0~10ppm 1ppm 2ppm 0.1ppm

Nitrogen Dioxide NO2 Electrochemical 0~20ppm 3ppm 5ppm 0.1ppm

Ethylene oxide C2H4O Electrochemical 0~30ppm 1ppm 2ppm 0.1ppm

Ethylene C2H4 Catalytic 0~100%LEL 15%LEL 50%LEL 1%LEL

Nitrogen Monoxide NO Electrochemical 0~100ppm 25ppm 50ppm 1ppm

Hydrogen fluoride HF Electrochemical 0~5ppm 0.5ppm 1ppm 0.1ppm

5
SI-100 MANUAL

2. Instrument Overview
1
2

3 1. OK/ERR LED (Power & Operation)

2. LOW Alarm (1st alarm)

3. HIGH Alarm (2nd alarm)

4. Sensor Housing and Sensor Part

5. Buttons (Use a Magnetic bar)

6
SI-100 MANUAL

3. How to install
Installing a detector at a site, opening the cover of a detector, or operating it may cause fire or
explosion depending on the environment. Therefore, you should proceed with your work after turning off
the power and examining whether explosive residual gas is around you or not.

3.1. How to fix

You can easily install a detector on a wall or ceiling like the above drawing by using M8 Bolts or other bolts.

3.2. How to open and wire

3.2.1 Separating Cover from Gas Detector Body

➢ Use a screwdriver to fasten the bolt (for

preventing separating of the Cover from the
body) of the enlarged picture on the side and
3.2.2 Gas Detector Wiring Diagram
turn it counterclockwise by two or three turns.
Then hold the cover of the gas monitor and
L H 485 turn it counterclockwise to remove the Cover.

7
 SI-100 MANUAL

DC 24V

4~20 mA
GND

L Contact output in LOW alarm (DRY or DC 24V)

H Contact output in HIGH alarm (DRY or DC 24V)
485 RS 485+ Telecommunication output

Normal : Dry
LOW : DRY LOW : 24V
1-2 pin connect : Dry HIGH : DRY HIGH : DRY

2-3 pin connect : 24V

LOW : DRY LOW : 24V

HIGH : 24V HIGH : 24V

4. Measuring Mode

4.1. Gas Detector Initial Operation

Power supply

8
SI-100 MANUAL

Showing
Version

Counting for
30 seconds

Failing to
Entering
initiate
Measuring
measuring
mode
mode
When this gas detector repeatedly fails to initiate measuring mode, first you should check the conditions
of the connection between gas sensors and the detector. When it is impossible for the detector to initiate
measuring mode even when the connection to the sensors is proper, the gas detector should require checks
and repairs. Therefore, please contact SENKO CO., LTD or your supplier.

Gas Sensor Connection Pin

(When this gas monitor fails to

initiate measuring mode, you need to
check whether pins are connected
correctly.)

9
SI-100 MANUAL

4.1.1 Initial Screen Explanation

Model Concentration

Gas Type

Unit

Bar graph (concentration) 4-20mA

4.2. Set Display

The displays are sequentially shown whenever you press each mode key ( ) by using a magnetic bar.

4.2.1 Description of Set Display

LCD Display Description

➢ GAS TYPE: measuring gas, automatic changes of related
information (Range, Low&High Alarm, Span, Unit and point, etc.)
➢ RANGE: maximum measurable range
➢ LOW AL: LOW (1st) alarm setting values
➢ HIGH AL: HIGH (2nd) alarm setting values
➢ SPAN: calibration gas concentration
➢ CAL TIME: required calibration time
➢ GAS UNIT: unit of measuring gas (%VOL, PPM or %LEL)
➢ DEC POINT: decimal point for measuring gas concentration
➢ CAL COUNT: No. of Span calibration (0-100), not able to change
➢ PWR DELAY: initial delay time settings in power supply
➢ AL DELAY: delay time settings for alarm occurrence
➢ INHIBIT: settings for holding alarm and current output

➢ COM: communication method (RS485 or HART or NONE)

➢ BAUD: communication speed (baud rate) settings (9600, 19200,
38400)
➢ ID : ID settings (0~254)

10
SI-100 MANUAL

4.3. Advanced setting

PUSH (2s) PUSH (2s) PUSH (2s)

➢ Press MODE key ( ) for 2 seconds by using the magnetic bar in Set Display to enter Advanced
setting.

➢ Press MODE key ( ) by using the magnetic bar in Advanced setting screen, in order to go to
another menu.

➢ Press DOWN key ( ) by using the magnetic bar to go back to the main menu (SET 1, 2 or 3).

➢ Without magnetic operation for 60 seconds, the display returns to the main menu (SET 1, 2 or 3).

11
SI-100 MANUAL

4.4. How to modify the settings [Flow chart]

“2sec”
Blinking Blinking

“2sec”

“1sec”

Blinking Blinking Blinking

Blinking Blinking

“2sec”

“1sec”

➢ Press MODE key ( ) for 2 seconds by using the magnetic bar in Set Display, in order to enter
Advanced setting.
➢ When you press UP key ( ) by using the magnetic bar in Advanced setting display, setting values
flicker, which means they can be changed.
➢ Press UP key ( ) when setting values flicker, in order to change the values.
➢ Press MODE key ( ) for 2 seconds to save the changes of setting values. These changes are saved
with the indication, “SAVED”.

✓ When GAS TYPE is changed, related settings (GAS UNIT, RANGE, ALAMR, etc.) are changed as well.
In order to operate properly, sensor replacement for the gas type and calibration is required.
✓ When you press DOWN key ( ) in each mode, the mode goes back to its previous step.

12
SI-100 MANUAL

4.5. Zero calibration & Span calibration

WARNING
Do not conduct Zero Calibration unless you are sure you are in fresh, uncontaminated air. Otherwise,
inaccurate reading can occur, then show that a hazardous atmosphere is safe. If you have any doubts as to
the quality of the surrounding air, Calibration with N2 gas should be done. Failure to follow this warning can
result in serious personal injury or death.
4.5.1 How to connect Calibration cap

➢ Correctly attach the calibration cap to the sensor part of the gas detector (SI-100) as the picture
above (using flow meter, etc., flow rate: about 300 SCCM) and inject the calibration gas.

4.5.2 Calibration Mode Explanation

Display of Calibration mode

Display in
ZERO/SPAN
Calibration

➢ In Calibration mode, the ADC values of ZERO and SPAN are displayed. When you conduct
ZERO/SPAN Calibration, Cal. Count starts counting. In the meantime, ADC Value (Present) is
displayed on the above part and ADC Value (Before Cal.) on the below part.

13
SI-100 MANUAL

4.5.3 How to enter Calibration Mode

➢ Press MODE key ( ) 4 times by using the magnetic bar in Measuring mode, in order to enter
Calibration mode.

➢ Press MODE key ( ) for 2 seconds by using the magnetic bar in Calibration mode, in order to
enter ZERO calibration when “ZERO” flickers. Then, press MODE key ( ) for 2 seconds once again
to initiate ZERO calibration.

➢ When ZERO calibration is completed, the display automatically shifts to SPAN calibration. The
process is same as ZERO calibration.

✓ If ZERO calibration ADC value (EX: 12667) goes beyond the SPAN calibration ADC value (EX: 14928),
you may suspect failure of calibration or malfunction of the gas sensor. In this case, you should
carry out recalibration or receive formal A/S to take appropriate measures for the case.

14
SI-100 MANUAL

5. Certificate

15
SI-100 MANUAL

16