Service Manual: Midea Airconditioner Europe Market Super DC Inverter Multi Type

SERVICE MANUAL
MIDEA AIRCONDITIONER
EUROPE MARKET
SUPER DC INVERTER MULTI TYPE
M2OD-14HFN1-Q
M2OD-16HFN1-Q
M2OD-18HFN1-Q
M3OD-21HFN1-Q
M3OD-26HFN1-Q
M3OD-27HFN1-Q
M4OD-28HFN1-Q
M4OA-36HFN1-Q
M5OC-36HFN1-Q
M5OD-42HFN1-Q
DC MULTI OUTDOOR UNITS
Downloaded from www.Manualslib.com manuals search engine

CONTENTS
1. General information of Outdoor Units .......................................... 3
2. Features .......................................................................................... 4
3. Dimensions ..................................................................................... 5
4. Wiring Diagram ............................................................................. 12
5. Refrigeration Cycle Diagram ....................................................... 16
6. Indoor units combination ............................................................ 19
7. Sound Levels ................................................................................ 22
8. Installation Details ........................................................................ 23
9. Electronic control function.......................................................... 34
10. Troubleshooting ......................................................................... 40

1. General information of Outdoor Units
Model name Dimension (mm) Compressor
M2OD-14HFN1-Q 845x320x700 DA130M1C-31FZ
M2OD-16HFN1-Q 810x310x558 ASN108D22UEZ
M2OD-18HFN1-Q 810x310x558 DA130M1C-31FZ
M2OD-18HFN1-Q 845x320x700 DA150S1C-20FZ
M3OD-27HFN1-Q 900x315x860 DA250S2C-30MT
M4OD-28HFN1-Q 900x315x860 DA250S2C-30MT
M4OA-36HFN1-Q 990x345x965 TNB306FPGMC-L
M5OC-36HFN1-Q 990x345x965 TNB306FPGMC-L
M5OD-42HFN1-Q 990x345x965 MNB36FAAMC-L

2. Features
Outdoor unit
Power relay control
Low noise air flow system
Hydrophilic aluminum fin
The hydrophilic fin can improve the heating efficiency at operation mode.
4 way valve control
It is only operated in the heating operation mode except defrosting operation.
Anti-rust cabinet
Valve protection cover
It protects the valves and prevents water from dripping.
Discharge pipe temperature protection

3. Dimensions
M2OD-14HFN1-Q, M2OD-18HFN1-Q
200.7
243.6
L1 L2
700
H
6
D1 335 560 W1
W2
D2 360 845 W 73
B1
110
B2 120
D3
D1
313
335
A2
58 58 58
H1 50 A1
22
R6 R5
110
H2

M2OD-16HFN1-Q, M2OD-18HFN1-Q(W190)
810 W3
558
H
10
D1 325 549 W1
W2
D2 348 795 W 64
B2 B1
D3 104.2 66.6
289
50 H1
A2
61.6
A1
90 H2
25.4
R20
R7.7

200.7
243.6
L1 L2
700
H
D1 335 560 W1
W2
D2 360 845 W 73
B1
110
B2 120
D3
D1
313
335
58 58 58 58 58
H1
A2
50 A1
22
R6 R5
110
H2

M3OD-27HFN1-Q
238.4
L1
285.7
L2
860
H
12
8
D1 333 590 W1
W2
D2 355 900 W 62
B2 B1
D3
90
97 D1
333
302
55 55 55 55 55
H1
A2
50
R6
110
H2

M4OD-28HFN1-Q
238.4
L1
285.7
L2
860
H
12
8
D1 333 590 W1
W2
D2 355 900 W 62
B2 B1
D3
90
97 D1
333
302
55 55 55 55 55 55 55
H1
A2
50
R6
110
H2

M4OA-36HFN1-Q
965
H
10
D1 366 624 W1
W2
D2 397 990 W 78
B1
125
D3 B2
145 D1
340
366
55
H1
A2
60 A1
22
R6 R5
140
H2

M5OC-36HFN1-Q, M5OD-42HFN1-Q
965 H
D1 366 624 W1
D2 397 990 W
W2 81
B2 125
55 H1
366 D1
D3 345
B1 145
A2
60 A1
153 H2
22
R6 R5

4. Wiring Diagram

M2OD-16HFN1-Q, M2OD-18HFN1-Q(W190)

M3OD-27HFN1-Q, M3OD-21HFN1-Q, M3OD-26HFN1-Q
M4OD-28HFN1-Q
M4OA-36HFN1-Q

M5OC-36HFN1-Q, M5OD-42HFN1-Q

5. Refrigeration Cycle Diagram
5.1 Refrigeration circuit drawing of inverter 1 drive 2 type
INDOOR OUTDOOR
EXV A CAPILIARY A
LIQUID VALVE A
CHECK VALVE
EXV B CAPILIARY B
LIQUID VALVE B T3
Condenser
temp. sensor
CAPILIARY TUBE
HEAT
EXCHANGE HEAT
T1 Room T4 Ambient
(EVAPORATOR) EXCHANGE
temp. sensor temp. sensor
(CONDENSER)
T2B-A Evaporator
T2 Evaporator GAS VALVE A temp. sensor outlet
temp. sensor
middle
4-WAY VALVE
T2B-B
GAS VALVE B
Accumulator
T5 Discharge
temp. sensor
Compressor COOLING
HEATING

INDOOR OUTDOOR
EXV A CAPILIARY A
LIQUID VALVE A
EXV B CAPILIARY B CHECK VALVE

LIQUID VALVE B
EXV C CAPILIARY C T3
LIQUID VALVE C Condenser
CAPILIARY TUBE temp. sensor
HEAT
EXCHANGE HEAT
T1 Room T4 Ambient
(CONDENSER)
T2B-A Evaporator
GAS VALVE A temp. sensor outlet
T2 Evaporator
temp. sensor
middle T2B-B
GAS VALVE B
4-WAY VALVE
T2B-C
GAS VALVE C
Accumulator T5 Discharge
temp. sensor COOLING
Compressor HEATING

INDOOR OUTDOOR
EXV A CAPILIARY A
LIQUID VALVE A
EXV B CAPILIARY B
LIQUID VALVE B
CHECK VALVE
EXV C CAPILIARY C
LIQUID VALVE C
T3
Condenser
EXV D CAPILIARY D CAPILIARY TUBE temp. sensor
LIQUID VALVE D
HEAT
EXCHANGE HEAT
T1 Room T4 Ambient
(CONDENSER)
T2B-A Evaporator
T2 Evaporator
temp. sensor T2B-B
GAS VALVE B
middle
4-WAY VALVE
T2B-C Accumulator
GAS VALVE C
High pressure
switch COOLING
GAS VALVE D T2B-D T5 Discharge HEATING
Low pressure temp. sensor
switch
Compressor
5.4 Refrigeration circuit drawing of M5OC-36HFN1-Q

INDOOR OUTDOOR
EXV A CAPILIARY A
LIQUID VALVE A
EXV B CAPILIARY B
LIQUID VALVE B
EXV C CAPILIARY C CHECK VALVE

LIQUID VALVE C
EXV D CAPILIARY D T3
LIQUID VALVE D Condenser
EXV E CAPILIARY E
LIQUID VALVE E
HEAT
EXCHANGE HEAT
T1 Room T4 Ambient
(CONDENSER)
T2B-A Evaporator
GAS VALVE B T2B-B

T2 Evaporator
temp. sensor
middle GAS VALVE C T2B-C
4-WAY VALVE
Accumulator
COOLING
GAS VALVE D T2B-D High pressure
switch HEATING
T5 Discharge
GAS VALVE E T2B-E Low pressure temp. sensor
switch
Compressor

5.5 Refrigeration circuit drawing of M5OD-42HFN1-Q
INDOOR OUTDOOR
EXV A CAPILIARY A
LIQUID VALVE A
EXV B CAPILIARY B
LIQUID VALVE B
EXV C CAPILIARY C CHECK VALVE

LIQUID VALVE C
EXV D CAPILIARY D T3
LIQUID VALVE D Condenser
EXV E CAPILIARY E
LIQUID VALVE E
HEAT
EXCHANGE HEAT
T1 Room T4 Ambient
(CONDENSER)
GAS VALVE A
T2 Evaporator GAS VALVE B

temp. sensor
GAS VALVE C
4-WAY VALVE
COOLING
GAS VALVE D Accumulator High pressure
switch HEATING
T5 Discharge
GAS VALVE E Low pressure temp. sensor
switch
Compressor

6. Indoor units combination
6.1 Indoor unit combination for M2OD-14HFN1-Q
One unit Two unit
7 7+7 9+9
9 7+9 9+12
12 7+12
18

One unit Two unit
7 7+7 9+9
9 7+9 9+12
12 7+12

One unit Two unit
7 7+7 9+9
9 7+9 9+12
12 7+12 9+18
18 7+18 12+12
6.4 Indoor unit combination for M3OD-21HFN1-Q, M3OD-26HFN1-Q

One unit Two unit Three unit
7 7+7 9+9 7+7+7 7+9+12
9 7+9 9+12 7+7+9 9+9+9
12 7+12 9+18 7+7+12 9+9+12
18 7+18 12+12 7+9+9

One unit Two unit Three unit
7 7+7 9+9 12+18 7+7+7 7+9+9 7+12+18 9+12+12
9 7+9 9+12 18+18 7+7+9 7+9+12 9+9+9 9+12+18
12 7+12 9+18 7+7+12 7+9+18 9+9+12 12+12+12
18 7+18 12+12 7+7+18 7+12+12 9+9+18

One unit Two unit Three unit Four unit

7 7+7 9+9 12+18 7+7+7 7+9+9 9+9+9 7+7+7+7 7+7+9+9 7+9+9+12
9 7+9 9+12 18+18 7+7+9 7+9+12 9+9+12 7+7+7+9 7+7+9+12 7+9+12+12
12 7+12 9+18 7+7+12 7+9+18 9+9+18 7+7+7+12 7+7+12+12 9+9+9+9
18 7+18 12+12 7+7+18 7+12+12 9+12+12 7+7+7+18 7+9+9+9 9+9+9+12
7+12+18
6.7 Indoor unit combination for M4OA-36HFN1-Q
One unit Two unit Three unit Four unit

7 7+7 9+9 12+12 7+7+7 7+12+12 9+12+18 7+7+7+7 7+7+12+12 7+9+12+18 9+9+12+12
9 7+9 9+12 12+18 7+7+9 7+12+18 9+18+18 7+7+7+9 7+7+12+18 7+9+18+18 9+9+12+18
12 7+12 9+18 18+18 7+7+12 7+18+18 12+12+12 7+7+7+12 7+7+18+18 7+12+12+12 9+12+12+12
18 7+18 7+7+18 9+9+9 12+12+18 7+7+7+18 7+9+9+9 7+12+12+18 9+12+12+18
7+9+9 9+9+12 12+18+18 7+7+9+9 7+9+9+12 9+9+9+9 12+12+12+12
7+9+12 9+9+18 7+7+9+12 7+9+9+18 9+9+9+12 12+12+12+18
7+9+18 9+12+12 7+7+9+18 7+9+12+12 9+9+9+18
6.8 Indoor unit combination for M5OC-36HFN1-Q

One Unit Two Unit Three Unit
7 7+7 9+12 7+7+7 7+9+18 9+9+18 12+18+18
9 7+9 9+18 7+7+9 7+12+12 9+12+12 18+18+18
12 7+12 12+12 7+7+12 7+12+18 9+12+18
18 7+18 12+18 7+7+18 7+18+18 9+18+18
9+9 18+18 7+9+9 9+9+9 12+12+12
7+9+12 9+9+12 12+12+18
Four Unit
7+7+7+7 7+7+9+18 7+9+9+18 7+12+18+18 9+9+18+18
7+7+7+9 7+7+12+12 7+9+12+12 9+9+9+9 9+12+12+12
7+7+7+12 7+7+12+18 7+9+12+18 9+9+9+12 9+12+12+18
7+7+7+18 7+7+18+18 7+9+18+18 9+9+9+18 12+12+12+12
7+7+9+9 7+9+9+9 7+12+12+12 9+9+12+12 12+12+12+18
7+7+9+12 7+9+9+12 7+12+12+18 9+9+12+18
Five Unit
7+7+7+7+7 7+7+7+9+18 7+7+9+12+18 7+9+9+12+18 9+9+9+12+12
7+7+7+7+9 7+7+7+12+18 7+7+12+12+18 7+9+12+12+12 9+9+9+12+18
7+7+7+7+12 7+7+7+18+18 7+9+9+9+9 7+9+12+12+18 9+9+12+12+12

7+7+7+7+18 7+7+9+9+9 7+9+9+9+12 9+9+9+9+9 9+12+12+12+12
7+7+7+9+9 7+7+9+9+12 7+9+9+9+18 9+9+9+9+12 12+12+12+12+12
7+7+7+9+12 7+7+9+9+18 7+9+9+12+12 9+9+9+9+18

One Unit Two Unit Three Unit
7 7+7 9+9 7+7+7 7+9+24 9+9+24 12+18+18
9 7+9 9+12 7+7+9 7+12+12 9+12+12 18+18+18
12 7+12 9+18 7+7+12 7+12+18 9+12+18
18 7+18 9+24 7+7+18 7+12+24 9+12+24
24 7+24 12+12 7+7+24 7+18+18 9+18+18
12+18 7+9+9 9+9+9 12+12+12
12+24 7+9+12 9+9+12 12+12+18
18+18 7+9+18 9+9+18 12+12+24
Four Unit
7+7+7+7 7+7+9+24 7+9+9+24 7+12+18+18 9+9+18+18
7+7+7+9 7+7+12+12 7+9+12+12 9+9+9+9 9+12+12+12
7+7+7+12 7+7+12+18 7+9+12+18 9+9+9+12 9+12+12+18
7+7+7+18 7+7+12+24 7+9+12+24 9+9+9+18 12+12+12+12
7+7+7+24 7+7+18+18 7+9+18+18 9+9+9+24 12+12+12+18
7+7+9+9 7+9+9+9 7+12+12+12 9+9+12+12
7+7+9+12 7+9+9+12 7+12+12+18 9+9+12+18
7+7+9+18 7+9+9+18 7+12+12+24 9+9+12+24
Five Unit
7+7+7+7+7 7+7+7+9+18 7+7+9+12+18 7+9+9+12+18 9+9+9+12+12
7+7+7+7+9 7+7+7+12+18 7+7+12+12+18 7+9+12+12+12 9+9+9+12+18
7+7+7+7+12 7+7+7+18+18 7+9+9+9+9 7+9+12+12+18 9+9+12+12+12
7+7+7+7+18 7+7+9+9+9 7+9+9+9+12 9+9+9+9+9 9+12+12+12+12
7+7+7+7+24 7+7+9+9+12 7+9+9+9+18 9+9+9+9+12 12+12+12+12+12
7+7+7+9+9 7+7+9+9+18 7+9+9+12+12 9+9+9+9+18
7+7+7+9+12

7. Sound Levels
Outdoor Unit
Microphone
1.0m
Note: H= 0.5 × height of outdoor unit
Model Noise Power dB(A) Noise level dB(A)

M2OD-14HFN1-Q 63 62
M2OD-16HFN1-Q 65 56
M2OD-18HFN1-Q(W190) 65 56
M2OD-18HFN1-Q(W210) 63 62
M3OD-21HFN1-Q 68 59
M3OD-26HFN1-Q 68 58
M3OD-27HFN1-Q 68 62
M4OD-28HFN1-Q 70 62
M4OA-36HFN1-Q 70 65
M5OC-36HFN1-Q 68 65
M5OD-42HFN1-Q 72 66

8. Installation Details
8.1 Wrench torque sheet for installation
Outside diameter Torque Additional tightening torque
mm N.cm N.cm
Ф6.35 1500(153kgf.cm) 1600(163kgf.cm)
Ф9.52 2500(255kgf.cm) 2600(265kgf.cm)
Ф12.7 3500(357kgf.cm) 3600(367kgf.cm)
8.2 Connecting the cables

The power cord of connect should be selected according to the following specifications sheet.
Rated current of appliance Nominal cross-sectional area (mm²)

>3 and ≤6 0.75
>6 and ≤10 1
>10 and ≤16 1.5
>16 and ≤25 2.5
The cable size and the current of the fuse or switch are determined by the maximum current indicated on the
nameplate which located on the side panel of the unit. Please refer to the nameplate before selecting the
cable, fuse and switch.
8.3 Pipe length and the elevation

Maximum piping length and height difference
1 drive 2 1 drive 3 1 drive 4 1 drive 5
Max. length for all rooms (m) 30 45 60 75
Max. length for one IU (m) 20 25 30 30
OU higher than IU 10 10 10 10
Max. height difference
between IU and OU (m) OU lower than IU 15 15 15 15
Max. height difference between IUs (m) 10 10 10 10
Additional refrigerant charge
1 drive 2 1 drive 3 1 drive 4 1 drive 5
Chargeless pipe
10 15 20 25
length (m)
Additional
15 x (length for all 15 x (length for all 15 x (length for all 15 x (length for all
refrigerant charge
rooms - 10) rooms - 15) rooms - 20) rooms - 25)
(g)
Caution:

● Refrigerant pipe diameter is different according to indoor unit to be connected. When using the
extension pipe, refer to the tables below.
● When refrigerant pipe diameter is different from that of outdoor unit union (for 18K indoor unit), additional
transfer connector needs to be used on outdoor unit union.
Indoor unit
Extension pipe diameter (mm/inch)
Model Pipe diameter (mm/inch)
Liquid 6.35(1/4) Liquid 6.35(1/4)

7K9K12K
Gas 9.52(3/8) Gas 9.52(3/8)
Liquid 6.35(1/4) Liquid 6.35(1/4)

18K
Gas 12.7(1/2) Gas 12.7(1/2)
Outdoor unit union diameter (mm/inch)
Liquid 6.35(1/4)
Indoor unit A/B/C/D
Gas 9.52(3/8)
8.4 Installation for the first time

Air and moisture in the refrigerant system have undesirable effects as below:
● Pressure in the system rises.
● Operating current rises.
● Cooling or heating efficiency drops.
● Moisture in the refrigerant circuit may freeze and block capillary tubing.
● Water may lead to corrosion of parts in the refrigerant system.
Therefore, the indoor units and the pipes between indoor and outdoor units must be leak tested and
evacuated to remove gas and moisture from the system.
Gas leak check (Soap water method):
Apply soap water or a liquid neutral detergent on the indoor unit connections or outdoor unit
connections by a soft brush to check for leakage of the connecting points of the piping. If bubbles come out,
the pipes have leakage.
1. Air purging with vacuum pump

(Indoor unit) (Liquid side) (Outdoor unit)
Two-way valve
Close
(Gas side)
Three-way valve
Manifold valve Close

Compound meter
Pressure
gauge
-0.1MPa
Lo Hi
Handle Lo Handle Hi
Charge hose Charge hose
Vacuum
pump
Vacuum
pump
1) Completely tighten the flare nuts of the indoor and outdoor units, confirm that both the 2-way and 3-way
valves are set to the closed position.
2) Connect the charge hose with the push pin of handle lo to the 3-way valves gas service port..
3) Connect the charge hose of handle hi connection to the vacuum pump.
4) Fully open the handle Lo of the manifold valve.
5) Operate the vacuum pump to evacuate.
6) Make evacuation for 30 minutes and check whether the compound meter indicates -0.1Mpa. If
the meter does not indicate -0.1Mpa after pumping 30 minutes, it should be pumped 20 minutes more. If the
pressure can’t achieve -0.1Mpa after pumping 50 minutes, please check if there are some leakage points.
Fully close the handle Lo valve of the manifold valve and stop the operation of the vacuum pump. Confirm
that the gauge needle does not move (approximately 5 minutes after turning off the vacuum pump).
7) Turn the flare nut of the 3-way valves about 45°counterclockwise for 6 or 7seconds after the gas
coming out, then tighten the flare nut again. Make sure the pressure display in the pressure indicator is a
little higher than the atmosphere pressure. Then remove the charge hose from the 3 way valve.
8) Fully open the 2 way valve and 3 way valve and securely tighten the cap of the 3 way valve.
2. Air purging by refrigerant

Procedure:
1). Confirm that both the 2-way and 3-way valves are set to the closed position.
2). Connect the charge set and a charging cylinder to the service port of the 3-way valve.
3). Air purging.
Open the valves on the charging cylinder and the charge set. Purge the air by loosening the flare nut on the
2-way valve approximately 45’ for 3 seconds then closing it for 1 minute; repeat 3 times.
After purging the air, use a torque wrench to tighten the flare nut on the 2-way valve.
4). Check the gas leakage.
Check the flare connections for gas leakage.
5). Discharge the refrigerant.
Close the valve on the charging cylinder and discharge the refrigerant by loosening the flare nut on the
2-way valve approximately 45’ until the gauge indicates 0.3 to 0.5 Mpa.
6). Disconnect the charge set and the charging cylinder, and set the 2-way and 3-way valves to the open
position.
Be sure to use a hexagonal wrench to operate the valve stems.
7). Mount the valve stems nuts and the service port cap.
Be sure to use a torque wrench to tighten the service port cap to a torque 18N·m.
Be sure to check the gas leakage.
3. Adding the refrigerant if the pipe length >5m

Electronic scale
Procedure:
1). Connect the charge hose to the charging cylinder, open the 2-way valve and the 3-way valve.
Connect the charge hose which you disconnected from the vacuum pump to the valve at the bottom of the
cylinder. If the refrigerant is R410A, make the cylinder bottom up to ensure the liquid charge.
2). Purge the air from the charge hose.

Open the valve at the bottom of the cylinder and press the check valve on the charge set to purge the air (be
careful of the liquid refrigerant).
3) Put the charging cylinder onto the electronic scale and record the weight.
4) Operate the air conditioner at the cooling mode.
5) Open the valves (Low side) on the charge set and charge the system with liquid refrigerant.
6).When the electronic scale displays the proper weight (refer to the table), disconnect the charge hose from
the 3-way valve’s service port immediately and turn off the air conditioner before disconnecting the hose.
7). Mount the valve stem caps and the service port
Use torque wrench to tighten the service port cap to a torque of 18N.m.
Be sure to check for gas leakage.

8.5 Adding the refrigerant after running the system for many years
Electronic scale
Procedure:
1). Connect the charge hose to the 3-way service port, open the 2-way valve and the 3-way valve.
Connect the charge hose to the valve at the bottom of the cylinder. If the refrigerant is R410A, make the
cylinder bottom up to ensure liquid charge.
2). Purge the air from the charge hose.

4) Operate the air conditioner at the cooling mode.
5) Open the valves (Low side) on the charge set and charge the system with liquid refrigerant.
6).When the electronic scale displays the proper weight (refer to the gauge and the pressure of the low side),
disconnect the charge hose from the 3-way valve’s service port immediately and turn off the air conditioner
before disconnecting the hose.
7). Mount the valve stem caps and the service port
8.6 Re-installation while the indoor unit need to be repaired

1. Collecting the refrigerant into the outdoor unit

Procedure
1). Confirm that both the 2-way and 3-way valves are set to the opened position
Remove the valve stem caps and confirm that the valve stems are in the opened position.
2). Connect the charge hose with the push pin of handle lo to the 3-way valves gas service port.
3). Air purging of the charge hose.
Open the handle Lo valve of the manifold valve slightly to purge air from the charge hose for 5 seconds and
then close it quickly.
4). Set the 2-way valve to the close position.
5). Operate the air conditioner at the cooling cycle and stop it when the gauge indicates 0.1MPa.
6). Set the 3-way valve to the closed position immediately
Do this quickly so that the gauge ends up indicating 0.3 to 0.5Mpa.
Disconnect the charge set, and tighten the 2-way and 3-way valve’s stem nuts.
Use a torque wrench to tighten the 3-way valves service port cap to a torque of 1.8 kgf.m.
2. Air purging by the refrigerant

Procedure:
1). Confirm that both the 2-way and 3-way valves are set to the closed position.
2). Connect the charge set and a charging cylinder to the service port of the 3-way valve
Leave the valve on the charging cylinder closed.
3). Air purging.
Open the valves on the charging cylinder and the charge set. Purge the air by loosening the flare nut on the
2-way valve approximately 45’ for 3 seconds then closing it for 1 minute; repeat 3 times.
After purging the air, use a torque wrench to tighten the flare nut on the 2-way valve.
4). Check the gas leakage
Check the flare connections for gas leakage.
5). Discharge the refrigerant.
Close the valve on the charging cylinder and discharge the refrigerant by loosening the flare nut on the
2-way valve approximately 45’ until the gauge indicates 0.3 to 0.5 Mpa.
6). Disconnect the charge set and the charging cylinder, and set the 2-way and 3-way valves to the open
position
7). Mount the valve stems nuts and the service port cap
Be sure to use a torque wrench to tighten the service port cap to a torque 18N.m.
Be sure to check the gas leakage.
8.7 Re-installation while the outdoor unit need to be repaired
1. Evacuation for the whole system

Procedure:
1). Confirm that both the 2-way and 3-way valves are set to the opened position.
2). Connect the vacuum pump to 3-way valve’s service port.
3). Evacuation for approximately one hour. Confirm that the compound meter indicates -0.1Mpa.
4). Close the valve (Low side) on the charge set, turn off the vacuum pump, and confirm that the gauge
needle does not move (approximately 5 minutes after turning off the vacuum pump).
5). Disconnect the charge hose from the vacuum pump.

2. Refrigerant charging
Procedure:
1). Connect the charge hose to the charging cylinder, open the 2-way valve and the 3-way valve
Connect the charge hose which you disconnected from the vacuum pump to the valve at the bottom of the
cylinder. If the refrigerant is R410A, make the cylinder bottom up to ensure liquid charge.
2). Purge the air from the charge hose
4). Open the valves (Low side) on the charge set and charge the system with liquid refrigerant
If the system cannot be charge with the specified amount of refrigerant, or can be charged with a little at a
time (approximately 150g each time) , operating the air conditioner in the cooling cycle; however, one time is
not sufficient, wait approximately 1 minute and then repeat the procedure.
5).When the electronic scale displays the proper weight, disconnect the charge hose from the 3-way valve’s
service port immediately
If the system has been charged with liquid refrigerant while operating the air conditioner, turn off the air
conditioner before disconnecting the hose.
6). Mounted the valve stem caps and the service port
Be sure to check for gas leakage

For M5OD-42HFN1-Q.There are one low-pressure centralized valve and one high-pressure centralized
valve, it will be more time saving when vacumm and recycle refrigerant. But refer to the previous instruction
when vacumm and recycle refrigerant.

9. Electronic control function
9.1 Abbreviation
T1: Indoor ambient temperature
T2: Coil temperature of indoor heat exchanger middle.

T2B: Coil temperature of indoor heat exchanger outlet.
T3: Coil temperature of outdoor heat exchanger

T4: Outdoor ambient temperature
T5: Compressor discharge temperature
Ts: Setting temperature
9.2 Electric control working environment.

9.2.1 Input voltage: 198V~264V.
9.2.2 Input power frequency:50Hz.
9.2.3 Indoor fan normal working amp. is less than 1A.
9.2.4 Outdoor fan. Normal working amp. is less than 1.5A.
9.2.5 Four-way valve normal working amp. is less than 1A.
9.3 Outdoor unit’s digital display tube

There is a digital display tube in outdoor PCB.
Digital display tube display function
 In standby , the LED displays “- -”
 In compressor operation, the LED display the running frequency,
 In defrosting mode, The LED displays “dF” or alternative displays between running frequency and
“dF”(each displays 0.5s)
 In compressor pre-heating, The LED displays “PH” or alternative displays between running frequency
and “PH”(each displays 0.5s)
 During the oil return process, The LED displays “RO” or alternative displays between running
frequency and “RO”(each displays 0.5s)
 In low ambient cooling mode, the LED displays “LC” or alternative displays between running
frequency and “LC”(each displays 0.5s)
 In forced cooling mode, the LED displays “FC” or alternative displays between running frequency and
“FC”(each displays 0.5s)
 When PFC module protection occurs three times within 15 minutes, the LED displays “E6” or
alternative displays between running frequency and “E6”(each displays 0.5s)
 In protection or malfunction, the LED displays error code or protection code.

9.4 Outdoor unit point check function
There is a check switch in outdoor PCB.
Press the switch N times it will display the content corresponding to No. N. After getting into the check function, it
will display No. N with 1.5s, meanwhile the low bit decimal of digit display flashing, indicated to get into the check
function display. After 1.5s, it will display the content corresponding to No. N.
the digital display tube will display the follow procedure when push SW1 each time.
Display Remark
0 Normal display Display running frequency, running state or malfunction code
1 No. of indoor units in good connection Actual data
2 Outdoor unit running mode code Off:0,Fan only 1, Cooling:2, Heating:3, Forced cooling:4
3 A indoor unit capacity
4 B indoor unit capacity
The capacity unit is horse power. If the indoor unit is not connected,
5 C indoor unit capacity the digital display tube will show: “――”
6 D indoor unit capacity (7K:0.8HP, 9K:1HP,12K:1.2HP,18K:1.5HP)
7 E indoor unit capacity

8 A Indoor unit capacity demand code
9 B Indoor unit capacity demand code
Norm value*HP
10 C Indoor unit capacity demand code
(7K:0.8HP, 9K:1HP,12K:1.2HP,18K:1.5HP)
11 D Indoor unit capacity demand code
12 E Indoor unit capacity demand code
13 Total indoor units amendatory capacity
Forced cooling:7
demand code
14 The frequency corresponding to the total
indoor units amendatory capacity demand
15 The frequency after the frequency limit
16 The frequency sending to compressor
control chip
17 A indoor unit evaporator outlet temp.(T2BA)
18 B indoor unit evaporator outlet temp.(T2BB) If the temp. is lower than -9 degree, the digital display tube will show
19 C indoor unit evaporator outlet temp.(T2BC) “-9”.If the temp. is higher than 70 degree, the digital display tube will
show “70”. If the indoor unit is not connected, the digital display tube
20 D indoor unit evaporator outlet temp.(T2BD) will show: “――”
21 E indoor unit evaporator outlet temp.(T2BE)
22 A indoor unit room temp.(T1A) If the temp. is lower than 0 degree, the digital display tube will show
“0”.If the temp. is higher than 50 degree, the digital display tube will
23 B indoor unit room temp.(T1B)
24 C indoor unit room temp.(T1C) will show: “――”
25 D indoor unit room temp.(T1D)
26 E indoor unit room temp.(T1E)
27 A indoor unit evaporator temp.(T2A)
28 B indoor unit evaporator temp.(T2B)
29 C indoor unit evaporator temp.(T2C) If the temp. is lower than -9 degree, the digital display tube will show
30 D indoor unit evaporator temp.(T2D) “-9”.If the temp. is higher than 70 degree, the digital display tube will
31 E indoor unit evaporator temp.(T2E) will show: “――”
32 Condenser pipe temp.(T3)
33 Outdoor ambient temp.(T4)
34 Compressor discharge temp.(T5) The display value is between 30~129 degree. If the temp. is lower
than 30 degree, the digital display tube will show “30”.If the temp. is
higher than 99 degree, the digital display tube will show single digit
and tens digit. For example, the digital display tube show “0.5”,it
means the compressor discharge temp. is 105 degree.)
35 AD value of current The display value is hex number.

36 AD value of voltage For example ,the digital display tube show “Cd”, it means AD value is
205.
37 EXV open angle for A indoor unit
Actual data/4.
38 EXV open angle for B indoor unit
If the value is higher than 99, the digital display tube will show single
39 EXV open angle for C indoor unit digit and tens digit.
40 EXV open angle for D indoor unit For example ,the digital display tube show “2.0”,it means the EXV
open angle is 120×4=480p.)
41 EXV open angle for E indoor unit
Frequency limit caused by IGBT
Bit7 The display value
radiator
is hex number. For
Bit6 Frequency limit caused by PFC example, the
Bit5 Frequency limit caused by T4. digital display tube
show 2A,then
42 Frequency limit symbol Bit4 Frequency limit caused by T2. Bit5=1, Bit3=1,
Bit3 Frequency limit caused by T3. Bit1=1.
It means
Bit2 Frequency limit caused by T5.
frequency limit
Bit1 Frequency limit caused by current caused by T4,T3
and current.
Bit0 Frequency limit caused by voltage
43 Average value of T2 (Sum T2 value of all indoor units)/( number of indoor units in good
connection)
44 Outdoor unit fan motor state Off:0, High speed:1, Med speed:2, Low speed:3 Breeze:4, Super
breeze:5
45 The last error or protection code 00 means no malfunction and protection
The following items from 9.4.1 to 9.4.5 are for the explanation of the point check functions.
9.4.1 Frequency of compressor:
Display Frequency of compressor (Hz)
30 30
-- Stand by
60 60
9.4.2 Running mode:
Display Corresponding mode
0 Off
1 Fan only
2 Cooling mode
3 Heating mode
4 Forced cooling
9.4.3 Capacity demand:

Cooling mode
T1 Ts
a 4
3 b 3
2 c 2
1 d 1
0 e 0
1 f

Capacity area a b c d e f
Norm value (N) 3 2 1.5 1 0.5 0
Heating mode
T1 Ts
4
3 f 3
2 e
2
1 d 1
0 c 0
b -1
a
Capacity area a b c d e f
Norm value (N) 3 2 1.5 1 0.5 0
9.4.4 Number of indoor unit

Display Number of indoor unit
1 1
2 2
3 3
4 4
5 5
9.4.5 Opening degree of electronic expansion valve:

Actual opening degree equals the display data times 4

9.5 Protection
9.5.1 Three minutes delay at restart for compressor.
9.5.2 Temperature protection of compressor discharge.
When the compressor discharge temp. is getting higher, the running frequency will be limited as below rules:
----If 102℃<T5<115℃, decrease the frequency to the lower level every 2 minutes till to F1.
---If T5>115℃ for 10 seconds, the compressor will stop and restart till T5<90℃.
9.4.3 Low voltage protection

VOLTAGE
No limit
VOLT_RST1_ADD
VOLT_LTM1_ADD
VOLT_LTM_FREQ1_ADD
VOLT_RST2_ADD
VOLT_LTM2_ADD
VOLT_LTM_FREQ2_ADD
Note: if the low voltage protection occurs and not resumes within 3min, it will keep the protection always
after restart the machine.
9.5.4 Compressor current limit protection
If the compressor current exceeds the current limit value for 10 seconds, the compressor frequency will be
limited as below table.
Cooling mode:
Current frequency（Hz） Current limit value（A） Frequency limit
COOL_F16 ICOOLLMT12 Decrease the frequency to COOL_F4 and run at COOL_F4 for
3 minutes.
COOL_F15 ICOOLLMT11
COOL_F14 ICOOLLMT10 After that, the frequency will be adjusted according to the
capacity demand and rise to the upper level every 3 minutes
COOL_F13 ICOOLLMT9 (When the frequency>COOL_F4 via capacity demand).
COOL_F12 ICOOLLMT8
COOL_F11 ICOOLLMT7
COOL_F10 ICOOLLMT6
COOL_F9 ICOOLLMT5
COOL_F8 ICOOLLMT4
COOL_F7 ICOOLLMT3
COOL_F6 ICOOLLMT2
COOL_F5 ICOOLLMT1
If the current frequency is lower than COOL_F4, the frequency will not be limited.
After 10s of the compressor start, if the current>ICOOL, the AC will display the failure for 30 seconds and stop. The AC
will restart 3 minutes later.
Heating mode:
Current frequency（Hz） Current limit value（A） Frequency limit
HEAT_F16 IHEATLMT12 Decrease the frequency to HEAT_F4 and run at HEAT_F4 for

HEAT_F15 IHEATLMT11 3 minutes.
HEAT_F14 IHEATLMT10 After that, the frequency will be adjusted according to the
capacity demand and rise to the upper level every 3 minutes
HEAT_F13 IHEATLMT9
(When the frequency>Heat_F4 via capacity demand).
HEAT_F12 IHEATLMT8
HEAT_F11 IHEATLMT7
HEAT_F10 IHEATLMT6
HEAT_F9 IHEATLMT5
HEAT_F8 IHEATLMT4
HEAT_F7 IHEATLMT3
HEAT_F6 IHEATLMT2
HEAT_F5 IHEATLMT1
If the current frequency is lower than HEAT_F4, the frequency will not be limited.
After 10s of the compressor start, if the current>IHEAT, the AC will display the failure for 30 seconds and stop. The AC
will restart 3 minutes later.
9.5.5 Indoor / outdoor units communication protection

If the indoor units can not receive the feedback signal from the outdoor units for 2 minutes, the AC will stop
and display the failure.
9.5.6 High condenser coil temp. protection.

When T3>65℃ for 3 seconds, the compressor will stop while the indoor fan and outdoor fan will continue.
When T3<52℃, the protection will release and the compressor will restart after 3 minutes.
9.5.7 Outdoor unit anti-freezing protection

For other models: When T2B<0℃ for 250 seconds, the indoor unit capacity demand will be zero and resume
to normal when T2B>10℃.
For M2OD-16HFN1-Q，M2OD-18HFN1-Q，M5OD-42HFN1-Q: When T2<4℃ for 250 seconds or T2<0℃,
the indoor unit capacity demand will be zero and resume to normal when T2>8℃ and the time of protection
is no less than 3 minutes.
9.5.8 Oil return

Running rules:
1. If the compressor frequency keeps lower than RET_OIL_FREQ1_ADD for RET_OIL_TIME1_ADD, the
AC will rise the frequency to RET_OIL_FREQ2_ADD for RET_OIL_TIME2_ADD and then resume to
former frequency.
2. The EXV will keep 300p while the indoor units will keep the current running mode.
If the outdoor ambient is higher than TempT4HeatLimit_ADD during the oil return, the AC quit oil return.

10. Troubleshooting
10.1 Indoor unit error code explanation:
PREMIER series +OASIS series+9A series +R series +12F series +Aurora series:
Display Operation lamp flash times Timer lamp Failure
E0 1 X Indoor EEPROM malfunction
E1 2 X Indoor / outdoor units communication error
E3 4 X Indoor fan speed has been out of control
E4 5 X Open or short circuit of T1 temperature sensor
E5 6 X Open or short circuit of T2 temperature sensor
F1 2 O Open or short circuit of T4 temperature sensor
F4 5 O Outdoor EEPROM parameter error
F5 6 O Outdoor fan speed out of control
F6 7 O Open or short circuit of T2B temperature sensor
P0 1 ☆ IPM module protection
P1 2 ☆ Voltage protection
P4 5 ☆ Inverter compressor drive protection
P5 6 ☆ Mode conflict
Low pressure protection(Just matching with

P6 7 ☆ M4OA-36HFN1-Q,M4OD-28HFN1-Q,M5OC-36HF
N1-Q, M5OD-42HFN1-Q)
O （light） X （off） ☆ （flash）
Light Commercial series(Except Console)

DISPLAY
NO. MALFUNCTION RUN Timer DEF Alarm
DIGITAL TUBE
1 Open or short circuit of T1 temperature sensor ☆ X X X E0
2 Open or short circuit of T2 temperature sensor X X ☆ X E1
3 Indoor / outdoor units communication error X ☆ X X E2
4 Full-water malfunction X X X ☆ E3
5 Indoor EEPROM malfunction ☆ ☆ X X E4

6 IPM module protection ☆ X X O E5
Open or short circuit of T3 or T4 temperature sensor or

7 ☆ O X X E6
Outdoor EEPROM malfunction
8 Outdoor fan speed has been out of control ☆ O ☆ X E7
9 Indoor fan speed has been out of control ☆ O O X F5
10 Voltage protection ☆ O X O P0
11 Outdoor unit over-current protection ☆ ☆ ☆ X P2
12 Inverter compressor drive protection ☆ ◎ X X P4
13 Mode conflict ☆ X O O P5
☆ Flash(at 2.5Hz) ◎ Flash(at 0.5Hz) O light X（off）
Note: Digital display is only available for A5 duct type.

For Console
NO. Malfunction Running lamp Timer lamp Defrosting lamp
1 Open or short circuit of T1 temperature sensor ☆ X X
2 Open or short circuit of T2 temperature sensor X X ☆
Communication malfunction between indoor and outdoor
3 X ☆ X
units.
4 Outdoor fan speed has been out of control X ☆ O
5 Indoor EEPROM malfunction ☆ ☆ X
6 IPM module protection ☆ X ☆
Open or short circuit of T3 or T4 temperature sensor or
7 ☆ ☆ ☆
Outdoor unit EEPROM parameter error
8 Voltage protection ☆ ☆ O
9 Inverter compressor drive protection ☆ ◎ X
10 Indoor fan speed has been out of control. ☆ O ☆
11 Mode conflict ☆ X O
O(light) X(off) ☆(flash at 5Hz) ◎(flash at 0.5Hz)

10.2 Outdoor unit error code explanation:
Display LED STATUS
E0 Outdoor EEPROM malfunction
E2 Indoor / outdoor units communication error
E3 Communication malfunction between IPM board and outdoor main board
E4 Open or short circuit of outdoor unit temperature sensor
E5 Voltage protection
E8 Outdoor fan speed has been out of control
F1 No A Indoor unit coil outlet temperature sensor or connector of sensor is defective
F2 No B Indoor unit coil outlet temperature sensor or connector of sensor is defective
F3 No C Indoor unit coil outlet temperature sensor or connector of sensor is defective
F4 No D Indoor unit coil outlet temperature sensor or connector of sensor is defective
F5 No E Indoor unit coil outlet temperature sensor or connector of sensor is defective
High pressure protection (For M4OA-36HFN1-Q, M4OD-28HFN1-Q, M5OC-36HFN1-Q,

P1 M5OD-42HFN1-Q)
Low pressure protection (For M4OA-36HFN1-Q, M4OD-28HFN1-Q, M5OC-36HFN1-Q,

P2
M5OD-42HFN1-Q)
P3 Current protection of compressor
P4 Temperature protection of compressor discharge
P5 High temperature protection of condenser
P6 IPM module protection
Note: Once these error codes display, they will disappear in at least 30 seconds if the unit come back to
normal.(Except E3&E4)

10.3 Trouble shooting
10.3.1 For the indoor unit
10.3.1.1 Indoor EEPROM malfunction
Power off, then restart the

unit 2 minutes later
Yes
Replace the indoor main PCB
EEPROM: An electrically erasable programmable read-only memory whose contents can be erased and
reprogrammed using a pulsed voltage.

10.3.1.2 Indoor / outdoor units communication error
Indoor / outdoor units communication error
Start: Power off , then Power on the

A/C by the Breaker. (reconnect the
power wire). Is it still displaying the
error code?
Yes
Check wiring on the outdoor and indoor

terminal follow the wiring diagram. Is all No Reconnect the wiring
connecting correctly?
No
No
Reconnect the wiring
Yes
Measure Vs, is it moving

Turn on all indoor unit by remote
alternately between positive value A: Is all the wiring between
No and negative value? (Vs is the No terminal and Indoor PCB
controller. Is all indoor unit display
voltage between S and N). Refer connect ok?
PIC 1
Yes Yes
Yes
Yes
Replace the Indoor PCB
Turn off the all indoor units. Is IPM Replace IPM board or
power LED or operating LED lamp No the outdoor main PCB
On? Refer PIC2
Power on by remote
controller, IIs it still
Yes displaying the error code
after 3 minutes?
Is main board“ ” Is the reactor connecting

No No Reconnect the wiring
lamp on? Refer PIC 3. well？
No
Yes Yes
Replace the outdoor main PCB
Is indoor units number correct? Check

on the outdoor check point . (2 for dual
Trouble is solved
zone, 3 for tri zone, 4 for qua zone,5 for
qui zone). Refer PIC 4.
No first time No second time A
Replacee outdoor unit PCB assembly(include

wiring) totally

Pic 1: check the voltage of N to S
(Vs), is it moving alternately
between positive value and negative
value?
Pic 2:IPM or outdoor main PCB (For

M2OD-14HFN1-Q/M2OD-18HFN1-Q
(W210) / M4OD-28HFN1-Q/tri-zone)
Operating
Self-Check
Pic 2: IPM or outdoor main PCB (For

M2OD-16HFN1-Q /
M2OD-18HFN1-Q(W190)/M4OA-36H
FN1-Q/ qui-zone)
Power,
Self-Check
els) Operating

PIC3 :Main board LED when power on and unit
standby.
. PIC 4: check point button,

Press 1 time for check how many indoor units are
connected

10.3.1.3 indoor unit fan speed has been out of control
Power
Power off,
off, then
then restart
restart the the
unit minutes later.
unit 22 minutes later. IsIs itit still
still No The
The unit
unit operates
operates normally.
normally.
displaying
displaying the
the error
error code?
code?
Yes
Find
Find out
out thethe cause
cause and
and
Shut
Shut offoff the
the power
power supply,
supply, have
have itit solved.
solved. For
For
rotate
rotate the fan by
the fan by hand.
hand. Does
Does No example,
example, whether
whether the
the fan
fan
itit rotate isis blocked
blocked oror the
the screws
screws
rotate properly?
properly?
which
which fix
fix the
the fan
fan are
are
tighten.
tighten.
Yes
Check
Check the
the wiring
wiring ofof fan
fan
motor.
motor. Are
Are all
all the
the No Correct
Correct the
the connections.
connections.
connections
connections good?
good?
Yes
Check
Check whether
whether the
the main
main PCB
PCB No Replace
Replace the
the main
main PCB
PCB
isis normal
normal through
through index
index 1?
1?
Yes
Replace
Replace the
the fan
fan motor
motor No
Index 1:
1: Indoor AC fan motor
Power on and set the unit running in fan mode at high fan speed. After running for 15 seconds, measure the
voltage of pin1 and pin2. If the value of the voltage is less than 100V(208~240V power supply)or 50V(115V
power supply), the PCB must have problems and need to be replaced.
2. Indoor DC fan motor(control chip is inside fan motor)

Power on and when the unit is in standby, measure the voltage of pin1-pin3, pin4-pin3 in fan motor
connector. If the value of the voltage is not in the range showing in below table, the PCB must have
problems and need to be replaced.
For other models:

For console:
5
4
6
1 3
2
DC motor voltage input and output

For split type:
NO. Color Signal Voltage
1 Red Vs/Vm 280V~380V
2 --- --- ---
3 Black GND 0V
4 White Vcc 14-17.5V
5 Yellow Vsp 0~5.6V
6 Blue FG 14-17.5V
For other types:

2 --- --- ---
3 Black GND 0V
4 White Vcc 13.5-16.5V
5 Yellow Vsp 0~6.5V
6 Blue FG 13.5-16.5V

10.3.1.4 Open or short circuit of temperature sensor.
Check
Check the
the connections
connections
between
between temperature
temperature No Correct
Correct the
the connections.
connections.
sensor
sensor and
and PCB.
PCB. Are
Are the
the
connections
connections good?
good?
Yes
Measure
Measure the
the resistance
resistance value
value
of
of the
the sensor
sensor via
via Appendix
Appendix 11
IsIs itit normal?

normal? No Replace
Replace the
the sensor.
sensor.
Yes
Replace
Replace the
the indoor
indoor PCB
PCB
10.3.1.6 Full-water malfunction

Power
Power off,off, then
then restart
restart the
the unit
unit 22 minutes
minutes
later.
later. Is
Is itit still
still displaying
displaying the
the error
error code?
code?
Yes
IfIf the
the water-level
water-level switch
switch No Insert
Insert the
the water-level
water-level switch
switch well
well
is
is inserted
inserted well?
well?
Yes
IfIf the
the water-level
water-level switch
switch Yes Replace
Replace the
the water-level
water-level switch
switch
is
is broken?
broken?
No
Replace
Replace the
the water
water pump,
pump, IfIf
malfunction
malfunction isis still
still not
not
solved
solved
Yes
Replace
Replace the
the indoor
indoor main
main PCB
PCB

10.3.2 For the outdoor unit
10.3.2 1 Outdoor EEPROM malfunction(ODU E0)
Power
Power off,
off, then
then restart
restart the
the
unit
unit 2 minutes later
2 minutes later
Yes
Replace
Replace the
the outdoor
outdoor main
main PCB
PCB
EEPROM: An electrically erasable programmable read-only memory whose contents can be erased and
reprogrammed using a pulsed voltage.

10.3.2.2 Communication malfunction between IPM board and outdoor main board(ODU E3)
E3 display
Communication malfunction between

IPM board and outdoor main board
Is there at least one LED in

the IPM board light?
No
Check the signal wire between

the IPM board and the main Yes
board, is it connected good?
No
Yes
Reconnect and retry. Is
error still display?
No
No
Replace IPM board, and
then check whether the Yes
system can run normally
No
Replace outdoor main

board, and then check
Yes
whether the system can run
normally
No
Replace the electric control

Trouble is solved
box

10.3.2.3 Voltage protection(ODU E5)
Voltage protection
Check the voltage of

outdoor unit power supply,
whether the voltage No Check the power supply
between L(L1) and N (L2) is
about 220~240VAC
Yes
Check whether the voltage

of IPM board P and N is
normal? DC277-356V for
18-27KBtu/h; DC277-410V
for 36-42KBtu/h
No
Replace bridge rectifiers,

and then check whether the
system can run normally Yes
Yes
No
Replace IPM board, and

then check whether the Yes
system can run normally
No
Replace outdoor main board Trouble is solved

10.3.2.4 Outdoor unit fan speed has been out of control (E8)
Power
Power off,
off, then
then restart
restart the the
unit
unit 22 minutes
minutes later.
later. IsIs itit still
still No The
The unit
unit operates
operates normally.
normally.
displaying
displaying the
the error
error code?
code?
Yes
Find
Find out
out thethe cause
cause and
and
Shut
Shut offoff the
the power
power supply,
supply, have
have itit solved.
solved. For
For
rotate
rotate the fan by
the fan by hand.
hand. Does
Does No example,
example, whether
whether the
the fan
fan
itit rotate isis blocked
blocked oror the
the screws
screws
rotate properly?
properly?
which
which fix
fix the
the fan
fan are
are
tighten.
tighten.
Yes
Check
Check the
the wiring
wiring ofof fan
fan
motor.
motor. Are
Are all
all the
the No Correct
Correct the
the connections.
connections.
connections
connections good?
good?
Yes
Check
Check whether
whether the
the main
main PCB
PCB No Replace
Replace the
the main
main PCB
PCB
isis normal
normal through
through index
index 1?
1?
Yes
Replace
Replace the
the fan
fan motor
motor No
Index 1:
1. Outdoor DC fan motor(control chip is inside fan motor)
Power on and when the unit is in standby, measure the voltage of pin1-pin3, pin4-pin3 in fan motor
connector. If the value of the voltage is not in the range showing in below table, the PCB must have
problems and need to be replaced.
DC motor voltage input and output

2 --- --- ---
3 Black GND 0V
4 White Vcc 13.5-16.5V
5 Yellow Vsp 0~6.5V
6 Blue FG 15V

10.3.2.5 High pressure protection (ODU P1) (For M4OA-36HFN1-Q, M4OD-28HFN1-Q,
M5OC-36HFN1-Q, M5OD-42HFN1-Q)
High
High pressure
pressure protection
protection
Whether
Whether the the wiring
wiring
between
between thethe high
high pressure
pressure
switch
switch and
and main
main control
control No Connect
Connect itit well
well
board
board is
is connected
connected well
well or
or
correctly
correctly
Yes
Whether
Whether the
the high
high
pressure
pressure protector
protector
is
is broken
broken
Method:
Method: Disconnect
Disconnect the
the plug.
plug.
Measure
Measure the
the resistance of the
resistance of the
high
high pressure
pressure protector,
protector, ifif No Replace
Replace high
high pressure
pressure protector
protector
the
the protector
protector is
is normal
normal thethe
value
value is
is o,
o,
Yes
Check
Check whether
whether the
the outdoor
outdoor
ambient
ambient temperature
temperature isis Yes Stop
Stop the
the unit
unit
higher
higher than
than 50℃
50℃
No
Check
Check ifif the
the outdoor
outdoor unit
unit
ventilation
NO Make
Make the
the outdoor
outdoor unit
unit ventilate
ventilate well
well
ventilation isis good
good
Yes
please
please refer
refer to
to the
the solution
solution of
of fan
fan
Check
Check ifif the
the outdoor
outdoor fan
fan runs
runs speed
speed has
has been
been outout of
of control
control
No malfunction
malfunction .. Find
Find out
out the
the cause
cause and
and
properly
properly
have
have itit solved.
solved.
Yes
Check
Check whether
whether the
the heat
heat
exchanger
Yes Clean
Clean the
the heat
heat exchanger
exchanger
exchanger is
is dirty
dirty
No
Replace
Replace outdoor
outdoor main
main
board
board
No
Check
Check whether
whether the
the refrigerant
refrigerant
system
system isis ok
ok

10.3.2.6 Low pressure protection (ODU P2) (For M4OA-36HFN1-Q, M4OD-28HFN1-Q,
M5OC-36HFN1-Q, M5OD-42HFN1-Q)
Low
Low pressure
pressure protection
protection
Whether
Whether the the wiring
wiring
between
between thethe low
low pressure
pressure
protector
protector and
and main
main control
control No Connect
Connect itit well
well
board
board is
is connected
connected well
well or
or
correctly
correctly
Yes
Whether
Whether thethe low
low
pressure
pressure protector
protector
is
is broken
broken
Method:
Method: Disconnect
Disconnect the
the plug.
plug.
Measure
Measure the
the resistance
resistance of
of the
the
low
low pressure
pressure protector.
protector. If
If the
the No Replace
Replace low
low pressure
pressure protector
protector
protector
protector is
is normal
normal the
the value
value isis
oo
Yes
Check
Check whether
whether the
the outdoor
outdoor
ambient
ambient temperature
temperature is
is too
too Yes Stop
Stop the
the unit
unit
low
low
No
Check
Check whether
whether valve
valve core
core
Open
Open fully
fully valve
valve core
core of
of
of
of high pressure valve
high pressure valve is
is No
high
high pressure
pressure valve
valve
opened
opened
Yes
please
please refer
refer to
to the
the solution
solution of
of fan
fan
Check
Check ifif the
the indoor
indoor fan
fan runs
runs speed
speed has
has been
been out
out of
of control
control
No malfunction.
malfunction. Find
Find out
out the
the cause
cause and
and
properly
properly in in cooling
cooling mode
mode
have
have itit solved.
solved.
Yes
Replace
Replace outdoor
outdoor main
main board
board
No
Refrigerant
Refrigerant isis not
not enough
enough add
add the
the
refrigerant
refrigerant
No
Check
Check whether
whether the
the refrigerant
refrigerant
system
system isis ok
ok

10.3.2.7 Current protection of compressor (ODU P3)
Current protection of compressor
Judge 1: Check whether the

input current of the power
supply wire is higher than max
protection current value
Yes
Check whether
the refrigerant
system is ok

outdoor ambient
Yes Stop the unit
temperature is higher than
50℃
No

Yes Make the outdoor unit ventilate well
outdoor unit is bad ventilation
No

Yes Clean the heat exchanger
heat exchanger is dirty
No
Let the refrigerant out, then use the high

Judge 5: The refrigerant
Yes pressure nitrogen or refrigerant to blow pipe,
pipe is blocked
vacuumize and charge the refrigerant again
No
Replace outdoor main

board,and check whether Yes
the system can run normally
No
Replace the electric control box Yes Trouble is solved
M2OD-16H M2OD-18HFN1 M2OD-18H M2OD-14H M3OD-21H M3OD-26H M3OD-27H M4OD-28H M4OA-36H M5OC-36H M5OD-42H
Model FN1-Q -Q(W190) FN1-Q FN1-Q FN1-Q FN1-Q FN1-Q FN1-Q FN1-Q FN1-Q FN1-Q
Max
prote
ction 11A 14A 15A 14A 15A 15A 18.5A 18A 23A 23A 25A
curre
nt

10.3.2.8 Temperature protection of compressor discharge (ODU P4)
Temperature
Temperature protection
protection of
of
compressor discharge
Check
Check whether
whether the
the
compressor Check
Check whether
whether the the
discharge temp.
temp. isis Yes Yes Stop
Stop leaking
leaking and
and add
add refrigerant
refrigerant
refrigerant
refrigerant isis leak
leak
more
more than 115°C ??
than 115°C
No
No
Check
Check whether
whether the
the
connection
connection isis right
right between
between
compressor
discharge temp.
temp. No Correct
Correct the
the wiring
wiring connection
connection
sensor
sensor and
and PCB
PCB according
according
to
to wiring
wiring diagrams?
diagrams?
Yes
Measure
Measure thethe resistance
resistance value
value
of compressor
of compressor discharge
discharge
temp.
temp. sensor.
sensor. IfIf the
the value
value is
is No Replace
Replace the
the compressor
discharge temp.
temp. sensor
sensor
not normal is
not normal is normal
normal refer
refer to
to
the
the Appendix
Appendix 2?
2?
Yes
Replace
Replace outdoor
outdoor main
main PCB
PCB
No
Replace
Replace high
high pressure
pressure valve
valve assy
assy

10.3.2.9 High temperature protection of condenser (ODU P5)
When outdoor pipe temperature is more than 65°C, the unit will stop, and unit runs again when outdoor pipe
temperature less than 52°C.
Check
Check the
the connection
connection
between
between temperature
temperature No Correct
Correct the
the connection
connection
High
High temperature
temperature protection
protection of
of No sensor
sensor and
and PCB.
PCB.
condenser
condenser
Yes
Check
Check whether
whether the
the
condenser
condenser temperature
temperature is
is Check
Check whether
whether the
the
Higher
Higher than
than 65°
65°C
C resistance
resistance of of condenser
condenser
temp.
temp. sensor
sensor is
is normal
normal
No Replace
Replace the
the temperature
temperature sensor
sensor
refer
refer to
to the
the Appendix
Appendix 11
Yes
Check
Check whether
whether the
the outdoor
outdoor
ambient
ambient temperature
temperature isis Yes Stop
Stop the
the unit
unit
higher
higher than
than 50℃
50℃
No
Check
Check ifif the
the outdoor
outdoor unit
unit
ventilation
No Make
Make the
the outdoor
outdoor unit
unit ventilate
ventilate well
well
ventilation isis good
good
Yes
please
please refer
refer to
to the
the solution
solution of
of fan
fan
Check
Check ifif the
the outdoor
outdoor fan
fan runs
runs speed
speed has
has been
been outout of
of control
control
No malfunction
malfunction .. Find
Find out
out the
the cause
cause and
and
properly
properly
have
have itit solved.
solved.
Yes
Check
Check whether
whether the
the heat
heat
exchanger
Yes Clean
Clean the
the heat
heat exchanger
exchanger Yes
exchanger is
is dirty
dirty
No
Replace
Replace outdoor
outdoor main
main
board
board
No
Refrigerant
Refrigerant isis not
not enough
enough add
add the
the
refrigerant
refrigerant
No
Check
Check whether
whether the
the refrigerant
refrigerant
system
system isis ok
ok

10.3.2.10 IPM module protection (ODU P6)
IPM module protection
Check whether the voltage range

Check whether the input Regulate it to correct, then
of P-N on IPM module is normal?
No power supply is correct? No check whether the system
DC277-356V for 18-27KBtu/h;
208-230V, 1N, 60Hz can work normally?
DC277-410V for 36-42KBtu/h
Yes
Yes No
Check whether the connecting

line between main board and Connect it tightly,
No
the IPM module is connected check ok or not? Check whether the
Connect it correctly
tightly power supply line is
No and tightly, check ok
connected correctly and
or not?
tightly
Yes
No
Yes No
Check whether the connecting

Connect it well, check
line of the compressor is No
ok or not?
connected correctly or tightly Check whether the lines
Connect it tightly,
in E-part box are No
check ok or not?
connected tightly
Yes
No
Yes No
Replace the IPM module,
check whether the system can
work normally? Check whether the bridge rectifiers are
normal? Use the multimeter to measure
the resistance between each two
terminals, check whether there is the
No condition that value of resistance is 0
No
Check whether the resistance of
the fan motor is normal. If not, Yes
Check if the outdoor fan replace the fan motor. For other Yes
runs properly or the outdoor Yes models, refer to the solution of Replace the bridge rectifiers
unit ventilation is good. fan speed has been out of
control malfunction . F i n d o u t
Check whether the connecting line of
the cause and have it solved. every reactor is normal? If the line is
broken, the resistance of the two ports is
No ∞（models except for M4OA-36HFN1-
Q,M4OD-28HFN1-Q, M5OC-36HFN1-
Q）；Check whether the PFC module
broken (for M4OA-36HFN1-Q,M4OD-
No
Replace the main board; check 28HFN1-Q, M5OC-36HFN1-Q,M50D-
whether the system can work Yes 42HFN1-Q)
normally?
Replace the connecting line or
reactor or replace the PFC
module(for M4OC-36HRFN1-
No M,M50D-42HFN1-Q)
Replace the compressor, check

Yes whether the system can work Yes
normally?
Trouble is solved

10.4 Main parts check
Spec.
Indoor unit
Model 7K 11M 9K 11M 12K 11M 18K 11M
Indoor fan motor WZDK20-38G WZDK20-38G WZDK20-38G WZDK58-38G
Model 9K 11P 12K 11P 18K 11P
Indoor fan motor WZDK20-38G WZDK20-38G WZDK20-38G
Model 7K 9A 9K 9A 12K 9A 18K(RC8) 9A 18K(RC4) 9A
Indoor fan motor WZDK20-38G RPG20D RPG20D WZDK30-38G RPG28D
Model 7K 12F 9K 12F 12K 12F 18K 12F
Indoor fan motor RPG20E RPG20E WZDK20-38G WZDK30-38G
Model 7K R 9K R 12K R 18K R
Indoor fan motor RPG13H RPG13H RPG20E RPG25
Model 7K A5 9K A5 12K A5 18K A5
Indoor fan motor WZDK27-38GS WZDK27-38GS WZDK27-38GS YSK68-4P
Model 7K Cassette 9K Cassette 12K Cassette 18K Cassette
Indoor fan motor WZDK37-38G WZDK37-38G WZDK37-38G YDK37-4P
Model 9K Console 12K Console 18K Console
Indoor fan motor RD-280-20-8A RD-280-20-8A RD-280-20-8A
Outdoor unit
Model 1x2(14k) 1x2(18k) 1x3(27K) 1x3(21K)
Compressor DA130M1C-31FZ DA150S1C-20FZ DA250S2C-30MT DA150S1C-20FZ
Outdoor fan motor WZDK50-38G WZDK50-38G WZDK72-38G WZDK50-38G
Model 1x4(28K) 1x4(36K) 1x5(36K) 1x5(42K)
Compressor DA250S2C-30MT TNB306FPGMC-L TNB306FPGMC-L MNB36FAAMC-L
Outdoor fan motor WZDK72-38G WZDK180-38G WZDK180-38G WZDK180-38G
Model 1x2(16k) 1x2(18k,W190)
Compressor ASN108D22UEZ DA130M1C-31FZ
Outdoor fan motor WZDK40-38G-W-1 WZDK40-38G-W-1

1. Temperature sensor checking
Disconnect the temperature sensor from PCB, measure the resistance value with a tester.
Temperature Sensors.
Room temp.(T1) sensor,
Indoor coil temp.(T2) sensor,
Outdoor coil temp.(T3) sensor,
Outdoor ambient temp.(T4) sensor,
Compressor discharge temp.(T5) sensor.
Measure the resistance value of each winding by using the multi-meter.

Appendix 1 Temperature Sensor Resistance Value Table for T1,T2,T3,T4,T2B (℃--K)
℃ K Ohm ℃ K Ohm ℃ K Ohm ℃ K Ohm
-20 115.266 20 12.6431 60 2.35774 100 0.62973
-19 108.146 21 12.0561 61 2.27249 101 0.61148
-18 101.517 22 11.5000 62 2.19073 102 0.59386
-17 96.3423 23 10.9731 63 2.11241 103 0.57683
-16 89.5865 24 10.4736 64 2.03732 104 0.56038
-15 84.2190 25 10.000 65 1.96532 105 0.54448
-14 79.3110 26 9.55074 66 1.89627 106 0.52912
-13 74.5360 27 9.12445 67 1.83003 107 0.51426
-12 70.1698 28 8.71983 68 1.76647 108 0.49989
-11 66.0898 29 8.33566 69 1.70547 109 0.48600
-10 62.2756 30 7.97078 70 1.64691 110 0.47256
-9 58.7079 31 7.62411 71 1.59068 111 0.45957
-8 56.3694 32 7.29464 72 1.53668 112 0.44699
-7 52.2438 33 6.98142 73 1.48481 113 0.43482
-6 49.3161 34 6.68355 74 1.43498 114 0.42304
-5 46.5725 35 6.40021 75 1.38703 115 0.41164
-4 44.0000 36 6.13059 76 1.34105 116 0.40060
-3 41.5878 37 5.87359 77 1.29078 117 0.38991
-2 39.8239 38 5.62961 78 1.25423 118 0.37956
-1 37.1988 39 5.39689 79 1.21330 119 0.36954
0 35.2024 40 5.17519 80 1.17393 120 0.35982
1 33.3269 41 4.96392 81 1.13604 121 0.35042
2 31.5635 42 4.76253 82 1.09958 122 0.3413
3 29.9058 43 4.57050 83 1.06448 123 0.33246
4 28.3459 44 4.38736 84 1.03069 124 0.32390
5 26.8778 45 4.21263 85 0.99815 125 0.31559
6 25.4954 46 4.04589 86 0.96681 126 0.30754
7 24.1932 47 3.88673 87 0.93662 127 0.29974
8 22.5662 48 3.73476 88 0.90753 128 0.29216
9 21.8094 49 3.58962 89 0.87950 129 0.28482
10 20.7184 50 3.45097 90 0.85248 130 0.27770
11 19.6891 51 3.31847 91 0.82643 131 0.27078
12 18.7177 52 3.19183 92 0.80132 132 0.26408
13 17.8005 53 3.07075 93 0.77709 133 0.25757
14 16.9341 54 2.95896 94 0.75373 134 0.25125
15 16.1156 55 2.84421 95 0.73119 135 0.24512
16 15.3418 56 2.73823 96 0.70944 136 0.23916
17 14.6181 57 2.63682 97 0.68844 137 0.23338
18 13.9180 58 2.53973 98 0.66818 138 0.22776
19 13.2631 59 2.44677 99 0.64862 139 0.22231

Appendix 2 Temperature Sensor Resistance Value Table for T5 (℃--K)
℃ K Ohm ℃ K Ohm ℃ K Ohm ℃ K Ohm
-20 542.7 20 68.66 60 13.59 100 3.702

-19 511.9 21 65.62 61 13.11 101 3.595
-18 483 22 62.73 62 12.65 102 3.492
-17 455.9 23 59.98 63 12.21 103 3.392
-16 430.5 24 57.37 64 11.79 104 3.296
-15 406.7 25 54.89 65 11.38 105 3.203
-14 384.3 26 52.53 66 10.99 106 3.113
-13 363.3 27 50.28 67 10.61 107 3.025
-12 343.6 28 48.14 68 10.25 108 2.941
-11 325.1 29 46.11 69 9.902 109 2.86
-10 307.7 30 44.17 70 9.569 110 2.781
-9 291.3 31 42.33 71 9.248 111 2.704
-8 275.9 32 40.57 72 8.94 112 2.63
-7 261.4 33 38.89 73 8.643 113 2.559
-6 247.8 34 37.3 74 8.358 114 2.489
-5 234.9 35 35.78 75 8.084 115 2.422
-4 222.8 36 34.32 76 7.82 116 2.357
-3 211.4 37 32.94 77 7.566 117 2.294
-2 200.7 38 31.62 78 7.321 118 2.233
-1 190.5 39 30.36 79 7.086 119 2.174
0 180.9 40 29.15 80 6.859 120 2.117
1 171.9 41 28 81 6.641 121 2.061
2 163.3 42 26.9 82 6.43 122 2.007
3 155.2 43 25.86 83 6.228 123 1.955
4 147.6 44 24.85 84 6.033 124 1.905
5 140.4 45 23.89 85 5.844 125 1.856
6 133.5 46 22.89 86 5.663 126 1.808
7 127.1 47 22.1 87 5.488 127 1.762
8 121 48 21.26 88 5.32 128 1.717
9 115.2 49 20.46 89 5.157 129 1.674
10 109.8 50 19.69 90 5 130 1.632
11 104.6 51 18.96 91 4.849
12 99.69 52 18.26 92 4.703
13 95.05 53 17.58 93 4.562
14 90.66 54 16.94 94 4.426
15 86.49 55 16.32 95 4.294 B(25/50)=3950K
16 82.54 56 15.73 96 4.167
17 78.79 57 15.16 97 4.045 R(90℃)=5KΩ±3%
18 75.24 58 14.62 98 3.927
19 71.86 59 14.09 99 3.812

2.Compressor checking
Measure the resistance value of each winding by using the tester.
Position Resistance Value
DA130M1C-31FZ DA150S1C-20FZ DA250S2C-30MT TNB306FPGMC-L ASN108D22UEZ MNB36FAAMC-L
Blue -
1.77Ω(20℃) 0.95Ω(20℃) 0.55Ω(20℃) 0.53Ω(20℃) 1.57Ω(20℃) 0.44Ω(20℃)
Red

3. IPM continuity check
Turn off the power, let the large capacity electrolytic capacitors discharge completely, and dismount the IPM. Use a digital
tester to measure the resistance between P and UVWN; UVW and N.
Digital tester Normal resistance value Digital tester Normal resistance value
(+)Red (-)Black (+)Red (-)Black
N U
∞ ∞
U V
P (Several MΩ) N (Several MΩ)
V W
W (+)Red
4: Indoor AC Fan Motor

Measure the resistance value of each winding by using the tester.
Resistance Value
Posi
tion RPG20D( RPG28D(T RPG28D( RPG20E(T RPG20E( RPG13H( RPG25(T YSK68-4P( YDK37
Weilng) ongDe) Dayang) ongDe) Weilng) Weilng) ongDe) Weilng) -4P
Blac 258.7
398Ω±8% 255Ω±8% 271.3Ω±8 415Ω±8% 387Ω±8% 575Ω±8% 295Ω±8% 285.8Ω±8
k- Ω±8%
(20℃) (20℃) % (20℃) (20℃) (20℃) (20℃) (20℃) % (20℃)
Red (20℃)
Red - 189.7
345Ω±8% 335Ω±8% 347.8Ω±8 396Ω±8% 378Ω±8% 558Ω±8% 420Ω±8% 178.5Ω±8
Yello Ω±8%
(20℃) (20℃) % (20℃) (20℃) (20℃) (20℃) (20℃) % (20℃)
w (20℃)
Yello 189.7
345Ω±8% 335Ω±8% 347.8Ω±8 396Ω±8% 378Ω±8% 558Ω±8% 420Ω±8% 178.5Ω±8
w- Ω±8%
(20℃) (20℃) % (20℃) (20℃) (20℃) (20℃) (20℃) % (20℃)
Blue (20℃)

Service Manual: Midea Airconditioner Europe Market Super DC Inverter Multi Type

Uploaded by

Copyright:

Available Formats

Service Manual: Midea Airconditioner Europe Market Super DC Inverter Multi Type

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Service Manual: Midea Airconditioner Europe Market Super DC Inverter Multi Type

Uploaded by

Copyright:

Available Formats

SERVICE MANUAL

DC MULTI OUTDOOR UNITS

Downloaded from www.Manualslib.com manuals search engine

1. General information of Outdoor Units .......................................... 3

4. Wiring Diagram ............................................................................. 12

5. Refrigeration Cycle Diagram ....................................................... 16

6. Indoor units combination ............................................................ 19

7. Sound Levels ................................................................................ 22

8. Installation Details ........................................................................ 23

9. Electronic control function.......................................................... 34

10. Troubleshooting ......................................................................... 40

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

Power relay control

Low noise air flow system

Hydrophilic aluminum fin

4 way valve control

It is only operated in the heating operation mode except defrosting operation.

Valve protection cover

It protects the valves and prevents water from dripping.

Discharge pipe temperature protection

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

Downloaded from www.Manualslib.com manuals search engine

5.2 Refrigeration circuit drawing of inverter 1 drive 3 type

EXV B CAPILIARY B CHECK VALVE

Downloaded from www.Manualslib.com manuals search engine

5.4 Refrigeration circuit drawing of M5OC-36HFN1-Q

EXV C CAPILIARY C CHECK VALVE

GAS VALVE B T2B-B

Downloaded from www.Manualslib.com manuals search engine

EXV C CAPILIARY C CHECK VALVE

T2 Evaporator GAS VALVE B

Downloaded from www.Manualslib.com manuals search engine

6.2 Indoor unit combination for M2OD-16HFN1-Q

6.3 Indoor unit combination for M2OD-18HFN1-Q

6.4 Indoor unit combination for M3OD-21HFN1-Q, M3OD-26HFN1-Q

6.5 Indoor unit combination for M3OD-27HFN1-Q

Downloaded from www.Manualslib.com manuals search engine

One unit Two unit Three unit Four unit

6.7 Indoor unit combination for M4OA-36HFN1-Q

One unit Two unit Three unit Four unit

6.8 Indoor unit combination for M5OC-36HFN1-Q

Downloaded from www.Manualslib.com manuals search engine

6.9 Indoor unit combination for M5OD-42HFN1-Q

Downloaded from www.Manualslib.com manuals search engine

Model Noise Power dB(A) Noise level dB(A)

Downloaded from www.Manualslib.com manuals search engine

8.2 Connecting the cables

Rated current of appliance Nominal cross-sectional area (mm²)