Work and

A machine makes doing

a job easier.

SECTION 1
Work and Power
Simple Machines
Main Idea Work is done
when a force causes an
object to move in the same
direction as the force.

SECTION 2
Using Machines
Main Idea A machine can
change the force needed to
do a job.

SECTION 3
Simple Machines
Main Idea There are six
types of simple machines.

Heav y Lif ting

It took the ancient Egyptians more than 100 years to build the
pyramids without machines like these. But now, even tall skyscrapers
can be built in a few years. Complex or simple, machines have the
same purpose. They make doing a job easier.
Science Journal Describe three machines you used today, and how they made
doing a task easier.

96 ◆
◆ M
(bkgd.)Rich Iwasaki/Getty Images
 Start-Up Activities
Simple Machines Many of the
devices that you use every day
are simple machines. Make the
Compare Forces following Foldable to help you understand the
characteristics of simple machines.
Two of the world’s greatest structures were
built using different tools. The Great
Pyramid at Giza in Egypt was built nearly STEP 1 Draw a mark at the
midpoint of a sheet of
5,000 years ago using blocks of limestone
paper along the side
moved into place by hand with ramps and edge. Then fold the
levers. In comparison, the Sears Tower in top and bottom
Chicago was built in 1973 using tons of edges in to touch
steel that were hoisted into place by gaso- the midpoint.
line-powered cranes. How do machines
such as ramps, levers, and cranes change STEP 2 Fold in half from side
the forces needed to do a job? to side.

1. Place a ruler
on an eraser. STEP 3 Turn the paper verti-
Place a book cally. Open and cut
along the inside fold
on one end
lines to form four tabs.
of the ruler.
2. Using one finger, push down on the free STEP 4 Label the tabs Inclined
end of the ruler to lift the book. Plane, Lever, Wheel and
3. Repeat the experiment, placing the eraser Axle, and Pulley.
in various positions beneath the ruler.
Observe how much force is needed in each Read for Main Ideas As you read the chapter, list
instance to lift the book. the characteristics of inclined planes, levers, wheels
and axles, and pulleys under the appropriate tab.
4. Think Critically In your Science Journal,
describe your observations. How did
changing the distance between the book
and the eraser affect the force needed to Preview this chapter’s content
lift the book? and activities at
bookm.msscience.com

M ◆ 97
(bkgd.)Rich Iwasaki/Getty Images, (inset)Mark Burnett
 Learn It! Knowing how to find answers to questions will
help you on reviews and tests. Some answers can be found in the textbook,
while other answers require you to go beyond the textbook. These answers
might be based on knowledge you already have or things you have
experienced.

Practice It! Read the excerpt below. Answer the follow-

ing questions and then discuss them with a partner.

Did you use a machine today? When you think

of a machine, you might think of a device, such as
a car, with many moving parts powered by an
engine or an electric motor. But if you used a pair
of scissors or a broom, or cut your food with a
knife, you used a machine. A machine is simply a
device that makes doing work easier. Even a sloping
surface can be a machine.
—from page 104

• Describe how using a broom makes cleaning a floor easier.

• How is pushing a box up a smooth ramp easier than lifting the
box upward?
• Why does a screwdriver make it easier to tighten a screw?

Apply It! Look at some ques-

tions in the text. Which questions can be
answered directly from the text? Which
require you to go beyond the text?

98 A ◆ M CHAPTER 4 Work and Simple Machines

 ack
r e ad , keep tr er
As you ons you answ
ti ll
of ques apter. This wi t
in the c h wha
Use this to focus on the main ideas as you read the chapter.
u rem ember
help yo .
d
Before you read the chapter, respond to the statements you rea
below on your worksheet or on a numbered sheet of paper.
• Write an A if you agree with the statement.
• Write a D if you disagree with the statement.

After you read the chapter, look back to this page to see if you’ve
changed your mind about any of the statements.
• If any of your answers changed, explain why.
• Change any false statements into true statements.
• Use your revised statements as a study guide.

Before You Read Statement After You Read

A or D A or D
1 Friction is caused by atoms or molecules of one
object bonding to atoms or molecules in
another object.
2 Power measures how fast work is done.
3 The fulcrum of a lever is always between the
input force and the output force.
4 Efficiency is the ratio of output work to input
Print out a worksheet work.
of this page at
bookm.msscience.com 5 When you do work on an object, you transfer
energy to the object.
6 A car is a combination of simple machines.
7 A wedge and a screw are both types of inclined
planes.
8 Work is done anytime a force is applied.
9 Mechanical advantage can never be less than 1.

M ◆ 98 B
 Work and Power
What is work?
What does the term work mean to you? You might think of
household chores; a job at an office, a factory, a farm; or the
■ Recognize when work is done.
homework you do after school. In science, the definition of
■ Calculate how much work is work is more specific. Work is done when a force causes an
done. object to move in the same direction that the force is applied.
■ Explain the relation between Can you think of a way in which you did work today? Maybe
work and power. it would help to know that you do work when you lift your
books, turn a doorknob, raise window blinds, or write with a
pen or pencil. You also do work when you walk up a flight of
If you understand work, you can
make your work easier. stairs or open and close your school locker. In what other ways
do you do work every day?
Review Vocabulary
force: a push or a pull Work and Motion Your teacher has asked you to move a box
of books to the back of the classroom. Try as you might, though,
New Vocabulary
you just can’t budge the box because it is too heavy. Although
•• work
power you exerted a force on the box and you feel tired from it, you
have not done any work. In order for you to do work, two things
must occur. First, you must apply a force to an object. Second,
the object must move in the same direction as
your applied force. You do work on an object
only when the object moves as a result of the
force you exert. The girl in Figure 1 might
think she is working by holding the bags of
groceries. However, if she is not moving, she is
not doing any work because she is not causing
something to move.

To do work, how must a

force make an object move?

Figure 1 This girl is holding bags of

groceries, yet she isn’t doing any work.
Explain what must happen for work to
be done.

98 ◆ M CHAPTER 4 Work and Simple Machines

Mary Kate Denny/PhotoEdit, Inc.
 Figure 2 To do work, an object
must move in the direction a force
Force is applied.

Force

Motion

Motion

The boy’s arms do work when they The boy’s arms still exert an
exert an upward force on the bas- upward force on the basket. But
ket and the basket moves upward. when the boy walks forward, no
work is done by his arms.

Applying Force and Doing Work Picture yourself lifting

the basket of clothes in Figure 2. You can feel your arms exert-
ing a force upward as you lift the basket, and the basket moves
upward in the direction of the force your arms applied.
Therefore, your arms have done work. Now, suppose you carry
the basket forward. You can still feel your arms applying an
upward force on the basket to keep it from falling, but now the
basket is moving forward instead of upward. Because the direc-
tion of motion is not in the same direction of the force applied
by your arms, no work is done by your arms.

Force in Two Directions Sometimes only part of the force

you exert moves an object. Think about what happens when you
push a lawn mower. You push at an angle to the ground as shown
in Figure 3. Part of the force is to the right and part of the force
is downward. Only the part of the force that is in the same direc-
tion as the motion of the mower—to the right—does work.

Figure 3 When you exert a

force at an angle, only part of
your force does work—the part
that is in the same direction as
the motion of the object.

M ◆ 99
(t)Richard Hutchings, (b)Tony Freeman/PhotoEdit, Inc.
 Calculating Work
Work is done when a force makes an object move. More work
is done when the force is increased or the object is moved a greater
James Prescott Joule This distance. Work can be calculated using the work equation below. In
English physicist experi-
mentally verified the law of
SI units, the unit for work is the joule, named for the nineteenth-
conservation of energy. He century scientist James Prescott Joule.
showed that various forms
of energy—mechanical,
Work Equation
electrical, and thermal—are work (in joules) 5 force (in newtons) 3 distance (in meters)
essentially the same and W 5 Fd
can be converted one into
another. The SI unit of
energy and work, the Work and Distance Suppose you give a book a push and it
joule, is named after him. slides across a table. To calculate the work you did, the distance
Research the work of Joule in the above equation is not the distance the book moved. The
and write what you learn distance in the work equation is the distance an object moves
in your Science Journal. while the force is being applied. So the distance in the work equa-
tion is the distance the book moved while you were pushing.

Solve a One-Step Equation

CALCULATING WORK A painter lifts a can of paint that weighs 40 N a distance of 2 m.

How much work does she do? Hint: to lift a can weighing 40 N, the painter must exert
a force of 40 N.

Solution
This is what you know: ● force: F 5 40 N
● distance: d 5 2 m
This is what you need to find out: work: W 5 ? J
This is the procedure you need Substitute the known values F 5 40 N and
to use: d 5 2 m into the work equation:
W 5 Fd 5 (40 N)(2 m) 5 80 N•m 5 80 J

Check your answer: Check your answer by dividing the work you cal-
culated by the distance given in the problem. The
result should be the force given in the problem.

1. As you push a lawn mower, the horizontal force is 300 N. If you push the mower a
distance of 500 m, how much work do you do?
2. A librarian lifts a box of books that weighs 93 N a distance of 1.5 m. How much work
does he do?
For more practice, visit
bookm.msscience.com/
math_practice

100 ◆ M CHAPTER 4 Work and Simple Machines

What is power?
What does it mean to be powerful? Imagine two weightlifters
lifting the same amount of weight the same vertical distance. They
Work and Power
both do the same amount of work. However, the amount of power
they use depends on how long it took to do the work. Power is how Procedure
1. Weigh yourself on a scale.
quickly work is done. The weightlifter who lifted the weight in less 2. Multiply your weight in
time is more powerful. pounds by 4.45 to convert
your weight to newtons.
Calculating Power Power can be calculated by dividing the 3. Measure the vertical
amount of work done by the time needed to do the work. height of a stairway.
WARNING: Make sure the
Power Equation stairway is clear of all
work (in joules) objects.
power (in watts) 5 4. Time yourself walking
time (in seconds) slowly and quickly up the
W stairway.
P5 t
Analysis
Calculate and compare
In SI units, the unit of power is the watt, in honor of James Watt, the work and power in
a nineteenth-century British scientist who invented a practical each case.
version of the steam engine.

Solve a One-Step Equation

CALCULATING POWER You do 200 J of work in 12 s. How much power did you use?
Solution
This is what you know: ● work: W 5 200 J
● time: t 5 12 s
This is what you need to find out: ● power: P 5 ? watts
This is the procedure you need Substitute the known values W 5 200 J and
to use: t 5 12 s into the power equation:
W 200 J
P 5 t 5 12 s 5 17 watts
Check your answer: Check your answer by multiplying the power you
calculated by the time given in the problem. The
result should be the work given in the problem.

1. In the course of a short race, a car does 50,000 J of work in 7 s. What is the power of the
car during the race?
2. A teacher does 140 J of work in 20 s. How much
power did he use?
For more practice, visit
bookm.msscience.com/
math_practice

SECTION 1 Work and Power M ◆ 101

 Work and Energy If you push a chair and make it move, you
do work on the chair and change its energy. Recall that when
something is moving it has energy of motion, or kinetic energy.
Topic: James Watt By making the chair move, you increase its kinetic energy.
Visit bookm.msscience.com for Web You also change the energy of an object when you do work
links to information about James and lift it higher. An object has potential energy that increases
Watt and his steam engine.
when it is higher above Earth’s surface. By lifting an object, you
Activity Draw a diagram show- do work and increase its potential energy.
ing how his steam engine worked.
Power and Energy When you do work on an object you
increase the energy of the object. Because energy can never be
created or destroyed, if the object gains energy then you must
lose energy. When you do work on an object you transfer energy
to the object, and your energy decreases. The amount of work
done is the amount of energy transferred. So power is also equal
to the amount of energy transferred in a certain amount of time.
Sometimes energy can be transferred even when no work
is done, such as when heat flows from a warm to a cold object. In
fact, there are many ways energy can be transferred even if no work
is done. Power is always the rate at which energy is transferred, or
the amount of energy transferred divided by the time needed.

Summary Self Check

What is work? 1. Describe a situation in which work is done on an object.

•Work is done when a force causes an object to

move in the same direction that the force is
2. Evaluate which of the following situations involves
more power: 200 J of work done in 20 s or 50 J of work
applied. done in 4 s? Explain your answer.

•If the movement caused by a force is at an angle

to the direction the force is applied, only the part
3. Determine two ways power can be increased.
4. Calculate how much power, in watts, is needed to cut a
of the force in the direction of motion does work. lawn in 50 min if the work involved is 100,000 J.
•Work can be calculated by multiplying the
force applied by the distance:
5. Think Critically Suppose you are pulling a wagon with
the handle at an angle. How can you make your task
W 5 Fd easier?

•The distance in the work equation is the distance

an object moves while the force is being applied.
What is power?
6. Calculate Work How much work was done to lift a
•Power is how quickly work is done. Something
is more powerful if it can do a given amount
1,000-kg block to the top of the Great Pyramid, 146 m
above ground?
of work in less time.
7. Calculate Work Done by an Engine An engine is used
•Power can be calculated by dividing the work
done by the time needed to do the work:
to lift a beam weighing 9,800 N up to 145 m. How
much work must the engine do to lift this beam?
P5 W How much work must be done to lift it 290 m?
t

102 ◆ M CHAPTER 4 Work and Simple Machines bookm.msscience.com/self_check_quiz

 Building the Pyramids
Imagine moving 2.3 million blocks of limestone, Work Done Using Different Ramps
each weighing more than 1,000 kg. That is
exactly what the builders of the Great Pyramid Distance (cm) Force (N) Work (J)
at Giza did. Although no one knows for sure
exactly how they did it, they probably pulled Do not write in this book.
the blocks most of the way.

Real-World Question 4. Arrange a notebook so that one end is on

How is the force needed to lift a block related to the stack of books and the other end is on the
the distance it travels? table. Measure the length of the notebook
and record this length as distance in the sec-
Goals ond row of the data table under Distance.
■ Compare the force needed to lift a block
5. Measure the force needed to pull the block
with the force needed to pull it up a ramp. up the ramp. Record the force in the data
Materials table.
wood block thin notebooks 6. Repeat steps 4 and 5 using a longer note-
tape meterstick book to make the ramp longer.
spring scale several books 7. Calculate the work done in each row of the
ruler data table.
Safety Precautions
Conclude and Apply
Procedure 1. Evaluate how much work you did in each
instance.
1. Stack several books together on a tabletop to
model a half-completed pyramid. Measure 2. Determine what happened to the force
the height of the books in centimeters. needed as the length of the ramp increased.
Record the height on the first row of the 3. Infer How could the builders of the pyramids
data table under Distance. have designed their task to use less force than
2. Use the wood block as a model for a block of they would lifting the blocks straight up? Draw
stone. Use tape to attach the block to the a diagram to support your answer.
spring scale.
3. Place the block on the table and lift it
straight up the side of the stack of books
until the top of the block is even with the
Add your data to that found by other
top of the books. Record the force shown on
groups. For more help, refer to the Science
the scale in the data table under Force.
Skill Handbook.

LAB M ◆ 103
 Using Machines
What is a machine?
Did you use a machine today? When you think of a machine
you might think of a device, such as a car, with many moving
■ Explain how a machine makes
parts powered by an engine or an electric motor. But if you used
work easier. a pair of scissors or a broom, or cut your food with a knife, you
■ Calculate the mechanical advan- used a machine. A machine is simply a device that makes doing
tages and efficiency of a machine. work easier. Even a sloping surface can be a machine.
■ Explain how friction reduces
efficiency.
Mechanical Advantage
Even though machines make work easier, they don’t decrease
Machines can’t change the amount the amount of work you need to do. Instead, a machine changes
of work you need to do, but they the way in which you do work. When you use a machine, you
can make doing work easier.
exert a force over some distance. For example, you exert a force
Review Vocabulary to move a rake or lift the handles of a wheelbarrow. The force
friction: force that opposes that you apply on a machine is the input force. The work you do
motion between two touching on the machine is equal to the input force times the distance
surfaces over which your force is applied. The work that you do on the
New Vocabulary machine is the input work.
•• input force
output force
The machine also does work by exerting a force to move an
object over some distance. A rake, for example, exerts a force to
•• mechanical
efficiency
advantage move leaves. Sometimes this force is called the resistance force
because the machine is trying to overcome some resistance. The
force that the machine applies is the output force. The work
that the machine does is the output work. Figure 4 shows how a
machine transforms input work to output work.
When you use a machine, the output work can never be
greater than the input work. So what is the advantage of using a
machine? A machine makes work easier by changing the
amount of force you need to exert, the distance over which the
force is exerted, or the direction in which you exert your force.

Figure 4 No matter what type

of machine is used, the output Machine
work is never greater than the
Input work Output work
input work.

104 ◆ M CHAPTER 4 Work and Simple Machines

Changing Force Some machines make doing a job easier by
reducing the force you have to apply to do the job. For this type of
machine the output force is greater than the input force. How much
larger the output force is compared to the input force is the
mechanical advantage of the machine. The mechanical advantage
of a machine is the ratio of the output force to the input force and
can be calculated from this equation: Topic: Historical Tools
Visit bookm.msscience.com for Web
Mechanical Advantage Equation links to information about early
output force (in newtons) types of tools and how they took
mechanical advantage 5
input force (in newtons) advantage of simple machines.
Fout Activity Write a paragraph
MA 5 F describing how simple machines
in
were used to design early tools.
Mechanical advantage does not have any units, because it is the
ratio of two numbers with the same units.

Solve a One-Step Equation

CALCULATING MECHANICAL ADVANTAGE To pry the lid off a paint can, you apply a force of
50 N to the handle of the screwdriver. What is the mechanical advantage of the
screwdriver if it applies a force of 500 N to the lid?

Solution
This is what you know: ● input force: Fin 5 50 N
● output force: Fout 5 500 N

This is what you need to find out: mechanical advantage: MA 5 ?

This is the procedure you need Substitute the known values Fin 5 50 N and Fout
to use: 5 500 N into the mechanical advantage equation:
Fout 500 N
MA 5 5 5 10
Fin 50 N

Check your answer: Check your answer by multiplying the mechani-

cal advantage you calculated by the input force
given in the problem. The result should be the
output force given in the problem.

1. To open a bottle, you apply a force of 50 N to the bottle opener. The bottle opener applies
a force of 775 N to the bottle cap. What is the mechanical advantage of the bottle opener?
2. To crack a pecan, you apply a force of 50 N to the nutcracker. The nutcracker applies a
force of 750 N to the pecan. What is the mechanical
advantage of the nutcracker?
For more practice, visit
bookm.msscience.com/
math_practice

SECTION 2 Using Machines M ◆ 105

Figure 5 Changing the direction
or the distance that a force is applied
can make a task easier.

Sometimes it is easier to exert your

force in a certain direction. This boy
would rather pull down on the rope to
lift the flag than to climb to the top of
the pole and pull up.

When you rake leaves, you

move your hands a short dis-
tance, but the end of the rake
moves over a longer distance.

Changing Distance Some machines allow you to exert your

force over a shorter distance. In these machines, the output force
is less than the input force. The rake in Figure 5 is this type of
machine. You move your hands a small distance at the top of the
handle, but the bottom of the rake moves a greater distance as it
moves the leaves. The mechanical advantage of this type of
machine is less than one because the output force is less than the
input force.

Changing Direction Sometimes it is easier to apply a force

in a certain direction. For example, it is easier to pull down on
the rope in Figure 5 than to pull up on it. Some machines enable
Figure 6 Machines are useful you to change the direction of the input force. In these machines
because they can increase force, neither the force nor the distance is changed. The mechanical
increase distance, or change the advantage of this type of machine is equal to one because the
direction in which a force is output force is equal to the input force. The three ways machines
applied. make doing work easier are summarized in Figure 6.
Larger force Smaller force
applied over a applied over a
Input force shorter distance Input force longer distance
Increases Increases
force distance

Force
applied over same
distance in a
Input force Changes different direction
direction
of force

106 ◆ M CHAPTER 4 Work and Simple Machines

(l)David Young-Wolff/PhotoEdit, Inc., (r)Frank Siteman/Stock Boston
Efficiency
A machine can’t make the output work greater than the input
work. In fact, for a real machine, the output work is always less
Body Temperature
than the input work. In a real machine, there is friction as parts of Chemical reactions that
the machine move. Friction converts some of the input work into enable your muscles to
heat, so that the output work is reduced. The efficiency of a move also produce heat
machine is the ratio of the output work to the input work, and that helps maintain your
can be calculated from this equation: body temperature. When
you shiver, rapid contrac-
Efficiency Equation tion and relaxation of
output work (in joules) muscle fibers produces a
efficiency (in percent) 5 3 100% large amount of heat that
input work (in joules) helps raise your body
Wout temperature. This causes
eff 5 3 100%
Win the efficiency of your
muscles to decrease as
If the amount of friction in the machine is reduced, the effi- more energy is converted
ciency of the machine increases. into heat.

Solve a One-Step Equation

CALCULATING EFFICIENCY Using a pulley system, a crew does 7,500 J of work to load
a box that requires 4,500 J of work. What is the efficiency of the pulley system?

Solution
This is what you know: ● input work: Win 5 7,500 J
● output work: Wout 5 4,500 J
This is what you need to find out: efficiency: eff 5 ? %
This is the procedure you need Substitute the known values Win 5 7,500 J and
to use: Wout 5 4,500 J into the efficiency equation:
Wout 4,500 J
eff 5 5 3 100% 5 60%
Win 7,500 J
Check your answer: Check your answer by dividing the efficiency by
100% and then multiplying your answer times
the work input. The product should be the work
output given in the problem.

1. You do 100 J of work in pulling out a nail with a claw hammer. If the hammer does
70 J of work, what is the hammer’s efficiency?
2. You do 150 J of work pushing a box up a ramp. If the ramp does 105 J of work, what is
the efficiency of the ramp?
For more practice, visit
bookm.msscience.com/
math_practice

SECTION 2 Using Machines M ◆ 107

 Surface
Friction To help understand friction, imagine pushing a heavy
box up a ramp. As the box begins to move, the bottom surface
of the box slides across the top surface of the ramp. Neither sur-
Oil face is perfectly smooth—each has high spots and low spots, as
shown in Figure 7.
As the two surfaces slide past each other, high spots on the
Surface two surfaces come in contact. At these contact points, shown in
Figure 7, atoms and molecules can bond together. This makes the
Figure 7 Lubrication can reduce contact points stick together. The attractive forces between all the
the friction between two surfaces. bonds in the contact points added together is the frictional force
Two surfaces in contact can stick that tries to keep the two surfaces from sliding past each other.
together where the high spots on To keep the box moving, a force must be applied to break the
each surface come in contact. bonds between the contact points. Even after these bonds are
Adding oil or another lubricant broken and the box moves, new bonds form as different parts of
separates the surface so that fewer the two surfaces come into contact.
high spots make contact.
Friction and Efficiency One way to reduce friction between
two surfaces is to add oil. Figure 7 shows how oil fills the gaps
between the surfaces, and keeps many of the high spots from
making contact. Because there are fewer contact points between
the surfaces, the force of friction is reduced. More of the input
work then is converted to output work by the machine.

Summary Self Check

What is a machine? 1. Identify three specific situations in which machines

•A machine is a device that makes doing work

easier.
make work easier.
2. Infer why the output force exerted by a rake must be

•A machine can make doing work easier by

reducing the force exerted, changing the
less than the input force.
3. Explain how the efficiency of an ideal machine com-
distance over which the force is exerted, pares with the efficiency of a real machine.
or changing the direction of the force. 4. Explain how friction reduces the efficiency of machines.
•The output work done by a machine can never
be greater than the input work done on the
5. Think Critically Can a machine be useful even if its
mechanical advantage is less than one? Explain and
machine. give an example.
Mechanical Advantage and Efficiency

•The mechanical advantage of a machine is the

number of times the machine increases the
input force: F 6. Calculate Efficiency Find the efficiency of a machine
MA 5 Fout if the input work is 150 J and the output work is 90 J.
in

• The efficiency of a machine is the ratio of the

output work to the input work:
7. Calculate Mechanical Advantage To lift a crate,
a pulley system exerts a force of 2,750 N. Find the
mechanical advantage of the pulley system if the
Wout
eff 5 W 3 100% input force is 250 N.
in

108 ◆ M CHAPTER 4 bookm.msscience.com/self_check_quiz

 Simple Machines
What is a simple machine?
What do you think of when you hear the word machine?
Many people think of machines as complicated devices such as
cars, elevators, or computers. However, some machines are as ■ Distinguish among the different
simple as a hammer, shovel, or ramp. A simple machine is a simple machines.
machine that does work with only one movement. The six sim- ■ Describe how to find the
ple machines are the inclined plane, lever, wheel and axle, screw, mechanical advantage of each
simple machine.
wedge, and pulley. A machine made up of a combination of sim-
ple machines is called a compound machine. A can opener is a
compound machine. The bicycle in Figure 8 is a familiar exam-
All machines, no matter how
ple of another compound machine. complicated, are made of simple
machines.
Inclined Plane
Review Vocabulary
Ramps might have enabled the ancient Egyptians to build compound: made of separate
their pyramids. To move limestone blocks weighing more than pieces or parts
1,000 kg each, archaeologists hypothesize that the Egyptians
built enormous ramps. A ramp is a simple machine known as an New Vocabulary
inclined plane. An inclined plane is a flat, sloped surface. Less •• simple machine
compound
•• screw
lever
force is needed to move an object from one height to another
using an inclined plane than is needed to lift the object. As the
machine
•• wedge
inclined plane
• wheel
axle
and

inclined plane becomes longer, the force needed to move the

object becomes smaller.
• pulley

Figure 8 Devices that use com-

Photo/Art ID #
binations of simple machines, such
as this bicycle, are called com-
pound machines.

M ◆ 109
Duomo
 Figure 9 Using an incline
plane, the force needed to move
the box to the back of the truck is
Weight = reduced compared to lifting the
1,500 N
box straight up.

Force = 300 N

1m
Force = 1,500 N 5m

Using Inclined Planes Imagine having to lift a box weigh-

ing 1,500 N to the back of a truck that is 1 m off the ground.
You would have to exert a force of 1,500 N, the weight of the
box, over a distance of 1 m, which equals 1,500 J of work. Now
suppose that instead you use a 5-m-long ramp, as shown in
Figure 9. The amount of work you need to do does not change.
You still need to do 1,500 J of work. However, the distance over
which you exert your force becomes 5 m. You can calculate the
force you need to exert by dividing both sides of the equation for
work by distance.
Figure 10 This chef’s knife is a Force 5 }}
work
wedge that slices through food. distance

If you do 1,500 J of work by exerting a force

over 5 m, the force is only 300 N. Because you
exert the input force over a distance that is five
times as long, you can exert a force that is five
times less.
The mechanical advantage of an inclined
plane is the length of the inclined plane divided by
its height. In this example, the ramp has a
mechanical advantage of 5.

Wedge An inclined plane that moves is called a

wedge. A wedge can have one or two sloping sides.
The knife shown in Figure 10 is an example of a
wedge. An axe and certain types of doorstops are
also wedges. Just as for an inclined plane, the
mechanical advantage of a wedge increases as it
becomes longer and thinner.

110 ◆ M CHAPTER 4 Work and Simple Machines

Robert Brenner/PhotoEdit, Inc.
Figure 11 Wedge-shaped
teeth help tear food. The wedge-shaped
teeth of this
Tyrannosaurus rex
show that it was a
carnivore.

Your front
teeth help
tear an apple
apart.

Wedges in Your Body You have

wedges in your body. The bite marks on
the apple in Figure 11 show how your front teeth are wedge
shaped. A wedge changes the direction of the applied effort
force. As you push your front teeth into the apple, the downward
effort force is changed by your teeth into a sideways force that
pushes the skin of the apple apart.
The teeth of meat eaters, or carnivores, are more wedge
shaped than the teeth of plant eaters, or herbivores. The teeth of
carnivores are used to cut and rip meat, while herbivores’ teeth
are used for grinding plant material. By examining the teeth of
ancient animals, such as the dinosaur in Figure 11, scientists can
determine what the animal ate when it was living.
Figure 12 The thread around
The Screw Another form of the inclined plane is a screw. A a screw is an inclined plane. Many
screw is an inclined plane wrapped around a cylinder or post. familiar devices use screws to
The inclined plane on a screw forms the screw threads. Just like make work easier.
a wedge changes the direction of the effort force
applied to it, a screw also changes the direction of
the applied force. When you turn a screw, the
force applied is changed by the threads to a force
that pulls the screw into the material. Friction
between the threads and the material holds the
screw tightly in place. The mechanical advantage
of the screw is the length of the inclined plane
wrapped around the screw divided by the length
of the screw. The more tightly wrapped the
threads are, the easier it is to turn the screw.
Examples of screws are shown in Figure 12.

How are screws related to the

inclined plane?

SECTION 3 Simple Machines M ◆ 111

(t)Tom McHugh/Photo Researchers, (b)Amanita Pictures
Figure 13 The mechanical Input Output
advantage of a lever changes force force Mechanical 10 cm 1
as the position of the fulcrum = =
advantage 50 cm 5
changes. The mechanical advan- 10 cm 50 cm
tage increases as the fulcrum is
moved closer to the output force.
Input Output
force force Mechanical 50 cm
= =
advantage 10 cm 5
50 cm 10 cm

Figure 14 A faucet handle is a

wheel and axle. A wheel and axle Lever
is similar to a circular lever. The You step up to the plate. The pitcher throws the ball and you
center is the fulcrum, and the swing your lever to hit the ball? That’s right! A baseball bat is a
wheel and axle turn around it. type of simple machine called a lever. A lever is any rigid rod or
Explain how you can increase the
plank that pivots, or rotates, about a point. The point about
mechanical advantage of a wheel
which the lever pivots is called a fulcrum.
and axle.
The mechanical advantage of a lever is found by dividing the
distance from the fulcrum to the input force by the distance
from the fulcrum to the output force, as shown in Figure 13.
When the fulcrum is closer to the output force than the input
force, the mechanical advantage is greater than one.
Levers are divided into three classes according to the posi-
tion of the fulcrum with respect to the input force and output
force. Figure 15 shows examples of three classes of levers.

Wheel and Axle

Wheel
Do you think you could turn a doorknob
easily if it were a narrow rod the size of a pen-
cil? It might be possible, but it would be diffi-
cult. A doorknob makes it easier for you to open
Axle a door because it is a simple machine called a
Input wheel and axle. A wheel and axle consists of
force two circular objects of different sizes that are
attached in such a way that they rotate together.
As you can see in Figure 14, the larger object is
the wheel and the smaller object is the axle.
The mechanical advantage of a wheel and
axle is usually greater than one. It is found by
dividing the radius of the wheel by the radius of
Output force the axle. For example, if the radius of the wheel
is 12 cm and the radius of the axle is 4 cm, the
mechanical advantage is 3.

112 ◆ M CHAPTER 4 Work and Simple Machines

Amanita Pictures
 NGS TITLE
VISUALIZING LEVERS
Figure 15

L
evers are among the simplest of machines, and you prob-
ably use them often in everyday life without even realiz-
ing it. A lever is a bar that pivots around a fixed point
called a fulcrum. As shown here, there are three types
of levers—first class, second class, and third class. They differ
in where two forces—an input force and an output force—
are located in relation to the fulcrum.

Fulcrum In a first-class lever, the fulcrum is

Input force between the input force and the
output force. First-class levers, such First-class lever
Output
force as scissors and pliers, multiply force
or distance depending on where the
fulcrum is placed. They always change
the direction of the input force, too.

In a second-class lever, such

as a wheelbarrow, the out- Second-class lever
put force is between the
input force and the fulcrum.
Second-class levers always
multiply the input force but
don‘t change its direction.

In a third-class lever, such as a baseball

Third-class lever
bat, the input force is between the out-
put force and the fulcrum. For a third-
class lever,the output force is less than the
input force,but is in the same direction.

SECTION 3 Simple Machines M ◆ 113

(t)Dorling Kindersley, (br bl)Bob Daemmrich
 Output force
Output
Input force force

Axle

Wheel
Input force
Wheel
Axle

Figure 16 The waterwheel and

Ferris wheel are examples of devices
that rely on a wheel and axle.
Compare and contrast water-
wheels and Ferris wheels in terms
of wheels and axles.
Using Wheels and Axles In some devices, the input force
is used to turn the wheel and the output force is exerted by the
axle. Because the wheel is larger than the axle, the mechanical
advantage is greater than one. So the output force is greater than
the input force. A doorknob, a steering wheel, and a screwdriver
are examples of this type of wheel and axle.
In other devices, the input force is applied to turn the axle
and the output force is exerted by the wheel. Then the mechan-
ical advantage is less than one and the output force is less than
the input force. A fan and a ferris wheel are examples of this type
of wheel and axle. Figure 16 shows an example of each type of
Observing Pulleys wheel and axle.
Procedure
1. Obtain two broomsticks.
Tie a 3-m-long rope to the
Pulley
middle of one stick. Wrap To raise a sail, a sailor pulls down on a rope. The rope uses a
the rope around both sticks simple machine called a pulley to change the direction of the
four times. force needed. A pulley consists of a grooved wheel with a rope
2. Have two students pull the or cable wrapped over it.
broomsticks apart while a
third pulls on the rope.
3. Repeat with two wraps of
Fixed Pulleys Some pulleys, such as the one on a sail, a win-
rope. dow blind, or a flagpole, are attached to a structure above your
head. When you pull down on the rope, you pull something up.
Analysis
1. Compare the results. This type of pulley, called a fixed pulley, does not change the
2. Predict whether it will be force you exert or the distance over which you exert it. Instead,
easier to pull the broom- it changes the direction in which you exert your force, as shown
sticks together with ten in Figure 17. The mechanical advantage of a fixed pulley is 1.
wraps of rope.
How does a fixed pulley affect the input force?

114 ◆ M CHAPTER 4 Work and Simple Machines

a(l)Wernher Krutein/Liaison Agency/Getty Images, (r)Siegfried Layda/Stone/Getty Images
 A fixed pulley changes A movable pulley A pulley system uses
the direction of the multiplies the several pulleys to
input force. input force. increase the mechanical
advantage.
Fixed pulley Movable pulley Pulley system

Movable Pulleys Another way to use a pulley is to attach it Figure 17 Pulleys can change
to the object you are lifting, as shown in Figure 17. This type of force and direction.
pulley, called a movable pulley, allows you to exert a smaller
force to lift the object. The mechanical advantage of a movable
pulley is always 2.
More often you will see combinations of fixed and movable
pulleys. Such a combination is called a pulley system. The
mechanical advantage of a pulley system is equal to the number
of sections of rope pulling up on the object. For the pulley
system shown in Figure 17 the mechanical advantage is 3.

Summary Self Check

Simple and Compound Machines 1. Determine how the mechanical advantage of a ramp

• A simple machine is a machine that does

work with only one movement.
changes as the ramp becomes longer.
2. Explain how a wedge changes an input force.

• A compound machine is made from a combi-

nation of simple machines.
3. Identify the class of lever for which the fulcrum is
between the input force and the output force.
Types of Simple Machines 4. Explain how the mechanical advantage of a wheel and
• An inclined plane is a flat, sloped surface. axle change as the size of the wheel increases.

• A wedge is an inclined plane that moves. 5. Think Critically How are a lever and a wheel and axle
similar?
• A screw is an inclined plane that is wrapped
around a cylinder or post.
• A lever is a rigid rod that pivots around a fixed
point called the fulcrum. 6. Calculate Length The Great Pyramid is 146 m high.
How long is a ramp from the top of the pyramid to the
• A wheel and axle consists of two circular
objects of different sizes that rotate together.
ground that has a mechanical advantage of 4?
7. Calculate Force Find the output force exerted by a
• A pulley is a grooved wheel with a rope or
cable wrapped over it.
moveable pulley if the input force is 50 N.

bookm.msscience.com/self_check_quiz SECTION 3 Simple Machines M ◆ 115

 Design Your Own
Pulley PUwer
Goals Real-World Question
■ Design a pulley system. Imagine how long it might have
■ Measure the mechani- taken to build the Sears Tower
cal advantage and effi- in Chicago without the aid of a
ciency of the pulley pulley system attached to a crane.
system. Hoisting the 1-ton I beams to a
maximum height of 110 stories
Possible Materials
required large lifting forces and
single- and multiple-
precise control of the beam’s
pulley systems
movement.
nylon rope
steel bar to support the Construction workers also
pulley system use smaller pulleys that are not
meterstick attached to cranes to lift supplies
*metric tape measure to where they are needed. Pulleys
variety of weights to test are not limited to construction
pulleys sites. They also are used to lift
force spring scale automobile engines out of cars, to help load and unload heavy objects
brick on ships, and to lift heavy appliances and furniture. How can you use a
*heavy book pulley system to reduce the force needed to lift a load?
balance
*scale Form a Hypothesis
*Alternate materials Write a hypothesis about how pulleys can be combined to make a sys-
Safety Precautions tem of pulleys to lift a heavy load, such as a brick. Consider the efficiency
of your system.

WARNING: The brick could

be dangerous if it falls.
Test Your Hypothesis
Keep your hands and feet Make a Plan
clear of it. 1. Decide how you are going to support your pulley system. What
materials will you use?
2. How will you measure the effort force and the resistance force?
How will you determine the mechanical advantage? How will you
measure efficiency?
3. Experiment by lifting small weights with a single pulley, double
pulley, and so on. How efficient are the pulleys? In what ways can
you increase the efficiency of your setup?

116 ◆ M CHAPTER 4 Work and Simple Machines

Tony Freeman/PhotoEdit, Inc.
4. Use the results of step 3 to design a pulley system to lift the brick. Draw a dia-
gram of your design. Label the different parts of the pulley system and use
arrows to indicate the direction of movement for each section of rope.
Follow Your Plan
1. Make sure your teacher approves your plan before you start.
2. Assemble the pulley system you designed. You might want to test it with a
smaller weight before attaching the brick.
3. Measure the force needed to lift the brick. How much rope must you pull to
raise the brick 10 cm?

Analyze Your Data

1. Calculate the ideal mechanical advantage of your design.
2. Calculate the actual mechanical advantage of the pulley system you built.
3. Calculate the efficiency of your pulley system.
4. How did the mechanical advantage of your pulley system compare with those
of your classmates?

Conclude and Apply

1. Explain how increasing the number of pulleys
increases the mechanical advantage.
Show your design diagram to the class.
2. Infer How could you modify the pulley system Review the design and point out good and
to lift a weight twice as heavy with the same bad characteristics of your pulley system.
effort force used here? For more help, refer to the Science Skill
3. Compare this real machine with an ideal Handbook.
machine.

LAB M ◆ 117
Aaron Haupt
 SCIENCE AND SCIENCE

Society ISSUES
THAT AFFECT
YOU!

Bionic People
Artificial limbs can help artificial body parts. A major
focus of bionics is the re-
people lead normal lives placement of lost limbs.
Through accident,

P
eople in need of transplants usually birth defect, or dis-
receive human organs. But many peo- ease, people
ple’s medical problems can only be sometimes
solved by receiving artificial body parts. These lack hands
synthetic devices, called prostheses, are used or feet, or
to replace anything from a heart valve to a even whole
knee joint. Bionics is the science of creating arms or legs.
For centuries, peo-
ple have used prostheses to replace limbs. In
the past, physically challenged people
used devices like peg legs or artificial arms
that ended in a pair of hooks. These prostheses
didn’t do much to replace lost functions of
arms and legs.
The knowledge that muscles respond to
electricity has helped create more effective
prostheses. One such prostheses is the myo-
electric arm. This battery-powered device
connects muscle nerves in an amputated
arm to a sensor.
The sensor detects when the arm tenses,
then transmits the signal to an artificial hand,
which opens or closes. New prosthetic hands
even give a sense of touch, as well as cold
and heat.

Myoelectric arms make life easier for

people who have them.

Research Use your school’s media center to find other aspects of

robotics such as walking machines or robots that perform planetary
exploration. What are they used for? How do they work? You could take For more information, visit
it one step further and learn about cyborgs. Report to the class. bookm.msscience.com/time

(t)Ed Kashi/CORBIS, (b)James Balog

 Work and Power 2. The mechanical advantage of a machine is
its output force divided by its input force.
1. Work is done when a force exerted on an
object causes the object to move.
2. A force can do work only when it is exerted Simple Machines
in the same direction as the object moves.
1. A machine that does work with only one
3. Work is equal to force times distance, and movement is a simple machine. A com-
the unit of work is the joule. pound machine is a combination of simple
4. Power is the rate at which work is done, machines.
and the unit of power is the watt. 2. Simple machines include the inclined
plane, lever, wheel and axle, screw, wedge,
Using Machines and pulley.
1. A machine can change the size or direction 3. Wedges and screws are inclined planes.
of an input force or the distance over which 4. Pulleys can be used to multiply force and
it is exerted. change direction.

Copy and complete the following concept map on simple machines.

Simple
Machines

Wheel and
Lever Pulley
axle

is a is a is a are

Rigid rod Two

Flat, sloped or plank that circular objects
surface rotates about a that rotate
fulcrum together

example example example example

bookm.msscience.com/interactive_tutor CHAPTER STUDY GUIDE M ◆ 119

(l)Inc. Janeart/The Image Bank/Getty Images, (r)Ryan McVay/PhotoDisc
 13. How much power is used when 600 J of
work are done in 10 s?
compound output force p. 104 A) 6 W C) 600 W
machine p. 109 power p. 101 B) 60 W D) 610 W
efficiency p. 107 pulley p. 114
inclined plane p. 109 screw p. 111 14. Which is a simple machine?
input force p. 104 simple machine p. 109 A) baseball bat C) can opener
lever p. 112 wedge p. 110 B) bicycle D) car
mechanical wheel and axle p. 112
advantage p. 105 work p. 98 15. Mechanical advantage can be calculated by
which of the following expressions?
A) input force/output force
Each phrase below describes a vocabulary word.
B) output force/input force
Write the vocabulary word that matches the
C) input work/output work
phrase describing it.
D) output work/input work
1. percentage of work in to work out
16. What is the ideal mechanical advantage of
2. force put into a machine a machine that changes only the direction
3. force exerted by a machine of the input force?
A) less than 1 C) 1
4. two rigidly attached wheels
B) zero D) greater than 1
5. input force divided by output force
Use the illustration below to answer question 17.
6. a machine with only one movement Wheel Radius 5 3 cm
7. an inclined plane that moves
Axle
8. a rigid rod that rotates about a fulcrum
9. a flat, sloped surface Input
10. amount of work divided by time force

Radius 5 1 cm Output force

Choose the word or phrase that best answers the 17. What is the output force if the input force
question. on the wheel is 100 N?
11. Which of the following is a requirement A) 5 N C) 500 N
for work to be done? B) 200 N D) 2,000 N
A) Force is exerted. 18. Which of the following is a form of the
B) Object is carried. inclined plane?
C) Force moves an object. A) pulley C) wheel and axle
D) Machine is used. B) screw D) lever
12. How much work is done when a force of 19. For a given input force, a ramp increases
30 N moves an object a distance of 3 m? which of the following?
A) 3 J C) 30 J A) height C) output work
B) 10 J D) 90 J B) output force D) efficiency

120 ◆ M CHAPTER REVIEW bookm.msscience.com/vocabulary_puzzlemaker

Use the illustration below to answer question 20. 26. Identify You have levers in your body. Your
9N muscles and tendons provide the input
force. Your joints act as fulcrums. The out-
put force is used to move everything from
your head to your hands. Describe and
3m
draw any human levers you can identify.
20. Evaluate Would a 9-N force applied 2 m 27. Display Make a display of everyday devices
from the fulcrum lift the weight? Explain. that are simple and compound machines.
For devices that are simple machines,
21. Explain why the output work for any machine
identify which simple machine it is. For
can’t be greater than the input work.
compound machines, identify the simple
22. Explain A doorknob is an example of a machines that compose it.
wheel and axle. Explain why turning the
knob is easier than turning the axle.
23. Infer On the Moon, the force of gravity is
less than on Earth. Infer how the mechan- 28. Mechanical Advantage What is the mechanical
advantage of a 6-m long ramp that extends
ical advantage of an inclined plane would
from a ground-level sidewalk to a 2-m high
change if it were on the Moon, instead of porch?
on Earth. 29. Input Force How much input force is required
24. Make and Use Graphs A pulley system has a to lift an 11,000-N beam using a pulley system
with a mechanical advantage of 20?
mechanical advantage of 5. Make a graph
with the input force on the x-axis and the 30. Efficiency The input work done on a pulley
system is 450 J. What is the efficiency of the
output force on the y-axis. Choose five dif- pulley system if the output work is 375 J?
ferent values of the input force, and plot
Use the table below to answer question 31.
the resulting output force on your graph.
Use the diagram below to answer question 25. Output Force Exerted by Machines
Machine Input Force (N) Output Force (N)
Total A 500 750
force = 50 N Vertical B 300 200
part = 30
C 225 225
D 800 1,100
Horizontal E 75 110
part = 40 N

25. Work The diagram above shows a force 31. Mechanical Advantage According to the table
exerted at an angle to pull a sled. How above, which of the machines listed has the
much work is done if the sled moves 10 m largest mechanical advantage?
horizontally?

bookm.msscience.com/chapter_review CHAPTER REVIEW M ◆ 121

Record your answers on the answer sheet Use the illustration below to answer questions 5 and 6.
provided by your teacher or on a sheet of paper.
1. The work done by a boy pulling a snow sled
up a hill is 425 J. What is the power expended
by the boy if he pulls on the sled for 10.5 s?
A. 24.7 W C. 247 W
B. 40.5 W D. 4460 W
Use the illustration below to answer questions 2 and 3.

Input Output 5. The pulley system in the illustration above

force force uses several pulleys to increase the mechan-
ical advantage. What is the mechanical
20 cm 120 cm advantage of this system?
A. 1 C. 3
2. What is the mechanical advantage of the B. 2 D. 4
lever shown above?
6. Suppose the lower pulley was removed so
1
A. }} C. 2 that the object was supported only by the
6
1
upper pulley. What would the mechanical
B. }} D. 6 advantage be?
2
3. What would the mechanical advantage of the A. 0 C. 2
lever be if the triangular block were moved to B. 1 D. 3
a position 35 cm from the edge of the output 7. You push a shopping cart with a force of
force side of the plank? 12 N for a distance of 1.5 m. You stop
1 pushing the cart, but it continues to roll
A. }} C. 3
4 for 1.1 m. How much work did you do?
1 A. 8.0 J C. 18 J
B. }} D. 4
3
B. 13 J D. 31 J
4. Which of the following causes the efficiency
of a machine to be less than 100%? 8. What is the mechanical advantage of a
A. work wheel with a radius of 8.0 cm connected
B. power to an axle with a radius of 2.5 cm?
C. mechanical advantage A. 0.31 C. 3.2
D. friction B. 2.5 D. 20
9. You push a 5-kg box across the floor with a
force of 25 N. How far do you have to push
Simplify Diagrams Write directly on complex charts, such as the box to do 63 J of work?
a Punnett square. A. 0.40 m C. 2.5 m
B. 1.6 m D. 13 m

122 ◆ M STANDARDIZED TEST PRACTICE

Record your answers on the answer sheet Record your answers on a sheet of paper.
provided by your teacher or on a sheet of paper. 19. The output work of a machine can never
10. What is the name of the point about be greater than the input work. However,
which a lever rotates? the advantage of using a machine is that it
makes work easier. Describe and give an
11. Describe how you can determine the
example of the three ways a machine can
mechanical advantage of a pulley or a
make work easier.
pulley system.
Use the figure below to answer questions 12 and 13.
20. A wheel and axle may have a mechanical
advantage that is either greater than 1 or
less than 1. Describe both types and give
some examples of each.
21. Draw a sketch showing the cause of fric-
tion as two surfaces slide past each other.
Explain your sketch, and describe how
12. What type of simple machine is the tip of lubrication can reduce the friction
the dart in the photo above? between the two surfaces.
13. Would the mechanical advantage of the 22. Draw the two types of simple pulleys and
dart tip change if the tip were longer and an example of a combination pulley. Draw
thinner? Explain. arrows to show the direction of force on
14. How much energy is used by a 75-W your sketches.
lightbulb in 15 s? Use the figure below to answer question 23.

15. The input and output forces are applied at

the ends of the lever. If the lever is 3 m
long and the output force is applied 1 m
from the fulcrum, what is the mechanical
advantage?
16. Your body contains simple machines.
Name one part that is a wedge and one
part that is a lever.
17. Explain why applying a lubricant, such as
oil, to the surfaces of a machine causes the
efficiency of the machine to increase. 23. Identify two simple machines in the photo
18. Apply the law of conservation of energy to above and describe how they make riding
explain why the output work done by a a bicycle easier.
real machine is always less than the input 24. Explain why the mechanical advantage of
work done on the machine. an inclined plane can never be less than 1.

bookm.msscience.com/standardized_test STANDARDIZED TEST PRACTICE M ◆ 123

(tl)Comstock Images, (br)PhotoDisc