Data Sheet Aton Pump 3 Compressed
Data Sheet Aton Pump 3 Compressed
Data Sheet Aton Pump 3 Compressed
SP 4”, 6” & 8”
The state of the art design is very energy efficient and offer a high performance
pumping therefore easy installation and low maintenance costs.
Technical Data:
- Motor Single Phase, 1x220 ~ 230V -50hz 220 Volt, 2850 rpm, 50 Hz
- NEMA Standard Dimensions
- Maximum start/stop 30 times in 1 hour
- Equipped with thermal overload protector
- Capacity up to 1800 L/min, 108 m³/hr
- Total Head up to 430 Meter
- Liquid temperature up to 40ºC
Application :
- Supply of raw water for households
- Supply of water from the wells to the reservoir
- Irrigation, Plantation and Agriculture
- Industrial and municipal application
SP 25 Series
Discharge Bowl
SUS304
Intermediate Chamber
SUS304
Impeller
SUS304
Strap
SUS304
Cable Guard
SUS304
Shaft
SUS304
SUS431 QT
Suction Interconnector
SUS304
Submersible Rewindable Motors
Characters :
• Conform to international standard of IEC34-1,CE, whole blocked
asynchronous motor with squirrel cage rotor.
• Outer shell, shaft and bottom made of stainless steel.
• Brass alloy or Nickel plated cast-iron upper bracket.
• Swedish bearing or equivalent products can undertake higher thrust load
• Italian mechanical seal.
• Pressure automatic adjusting device made of oil-prof and waterproof
reformed butyl rubber.
• Flange connector conform to the standard of NEMA (USA National
Electrical Manufacturing Association).
• Lacquer-coated wire conforms to USA standard of NEMA MW37-C.
Properties :
• Power: Single-phase: 0.25kW - 2.2kW, Three-phase: 0.55kW - 37kW
• Voltage: Single-phase 180/230V (-6% +10%) or 230/240V (+6% -10%)
50Hz Three-phase 230V or 400V ± 10% 50Hz
• Thrust Ioad:
1500N (0.25kW - 0.75kW)
2500N (1.1kW - 5.5kW)
4500N (3.0kW - 7.5kW)
• Degree of protection: 1P68
• Insulation: Class B
• Max. Water Temperature : 35°C, Max. Ambient temperature: 40°C
• Minimum cooling flow along the motor: 8cm/sec.
• Water pH: 6.5 - 8.0
• Maximum starts per hour: 20
• Maximum submerged depth: 4” Max. 150 meters, 6” Max. 300 meters
• Vertical or horizontal mounting position
• Motor protection by temperature compensated thermal relay and
extra-quick trip overload
• Overload trip time:
<10 seconds (when load is 5 times of rating current)
• Flat water-proof cable 4x1.5 mm² or 4x2.5 mm² with separated earth
wire (see table enclosed)
Dimension: 19.2 X 6.2 mm²
Length: 0.9m (0.37- 0.55kW);
1.2m (0.75-1.1kW);
1.5m (1.5-2.2kW);
1.6m (3.0kW);
2.0m (4.0-5.5kW);
2.5m (7.5kW)
• Special request product required by customers can be provided
Materials :
• high-quality cold-rolled silicon steel lamination.
• Special mechanical seal design.
• 220°C-resistant lacquer-coated wires.
• high-quality bearing undertaking big thrust load.
Performance Curve
SP 25
350
SP-25
50 Hz
SP-2552 ISO 9906 Annex A
300
SP-2544
250
SP-2538
SP-2533
200
SP-2525
150
SP-2521
SP-2517
100
SP-2512
50 SP-2508
SP-2506
SP-2504
0
0 10 20 30 40 50 60 70 80 90 100 110 120 130 140 L/Min
0 0.6 1.2 1.8 2.4 3 3.6 4.2 4.8 5.4 6 6.6 7.2 7.8 8.4 m³/hr
0 0.17 0.33 0.5 0.67 0.83 1 1.17 1.33 1.5 1.67 1.83 2 2.17 2.33 L/s
0 0.6 1.2 1.8 2.4 3 3.6 4.2 4.8 5.4 6 6.6 7.2 7.8 8.4 m³/hr
Dimensions and weights
SP 25