F E D C B A

REV.NO DETAILS OF REVISION BY DATE

00 NEW RELEASE HRUSHIKESH 10-07-23

1
5
1
MARKED AREA
2

TIG SEE DETAIL A 4

(4 X 90 1
BOTH SIDE)

STATIC CHARACTERISTICS
F in N

Max. allowable disp.

+ | d(-) | | d(+) |
F,d
98)

F (+)
2 - 2
102.5 0.5

Opr. disp.
(GAS FLOW I.D.

101-0.5

( 124)
0

O.D

O.D
0
d in mm
Wv,g
F (-)

d(-) d(+)

NOTE:
1. REMOVE ALL BURS AND SHARP EDGES.
2. BELLOW LEAK RATE SHALL BE 0.05 l/min. WITH SUBJECTED TO 0.5 BAR INTERNAL
PRESSURE.
3. ALL LAYERS BETWEEN END CAP AND INTERFACE DIAMETER TO BE FLUSH OR
POSITIVELY STACKED; WITH EXCEPTION OF THE RING WHICH CAN BE 1MM
MAX INSET FROM LINER END.
SEE DETAIL B 4. NO OF PLY : 02
(181) TIG 5. PLY THICKNESS : 0.25 MM
3 6. NO OF CORRUGATIONS : 21
7. END CAP TO BE MARKED WITH ADMJF-DD-M-YY-SHIFT
3
8. APPEARANCE OF BELLOW AS PER ADMES001 STD.
203 3 9. OPERATIONAL DISPLACEMENT

AXIAL 15 mm
276 3 SHEAR 15 mm

10. CAD WEIGHT : 1.574 KG.(APPROX.)

9.2 0.2 10 2

R4 SPRING CONSTANT
TYP. AXIAL STIFFNESS 30 3 N/mm
SHEAR STIFFNESS 28 3 N/mm

5 BRAID SS 304 01
4 END ADAPTOR SS 304 01
40 2 3 BELLOW SS 321 01
2 0.2 THK.

2 END CAP SS 409 02

(1.5) 1 INTERLOCK SS 321 01
SR.NO DESCRIPTION MATERIAL QTY
4 DATE
DEVELOPMENT DRAWING SIGN
DETAIL B
SCALE 2.000
HRUSHIKESH GANESH RATENDRA
4
Drawn By Checked By Approved By

UNLESS OTHERWISE STATED, ALL DIMENSIONS ARE ARE IN MM . DO NOT SCALE THE DRAWING. IF IN DOUBT, ASK. CONFIDENTIAL CUSTOMER: VECV SCALE: 1.5:1
DEVIATION FOR OPEN DIMENSIONS (MED TO IS:2002) C 2001 THIS DRAWING AND ALL INFORMATION THEREON IS THE PROPERTY
CLASSIFICATION OF CHARACTERISTICS SURFACE ROUGHNESS SYMBOLS ID377381
OF iAi JOIN FLEX (I) PVT. LTD. AND MUST NOT BE COPIED TRANSMITTED OR PROJECT: SIZE: A1
GENERAL TOLERANCES FOR FABRICATION UNLESS OTERWISE STATED
GRD HRD & GRD
LINEAR DIMENSIONS & HOLE CENTERS 1
CRITICAL MAJOR NEW
N11 N9 N6 N3
N6 N6 REPRODUCED DIRECTLY OR INDIRECTLY WITHOUT iAi JOIN FLEX'S PERMISSION.
PIECES PARTS MACHINING ASSEMBLIES 0.15
APPLIES TO UPPER LIMIT 0-500 1 0-30 0.1 0-100 0.5
DRILLED HOLES UPTO Ø8 DESCRIPTION: FINISHED PRODUCT - FLEX (102 x 276 MM)
2 %OF OLD
OVER 500-1000 1.5 30-60 0.2 OVER 100-500 1 DRILLED HOLES OVER Ø8 Ø
APPLIES TO LOWER LIMIT OVER 1000-2000
2000 AND OVER
1.5
5
60-180
180-500
0.3
0.4
OVER 500-2000
2000 & OVER
1.5
3
ANGLES 1 ADM JOINFLEX INDIA PVT LTD DRG. NO. : 006FLX4FSS00000513 SHEET
KEY INSTRUCTIONS ANGLES 1 500 & ABOVE 0.5 ANGLES 1 Ra ON MACHINED SURFACE 6.3
FOR OTHER : IS 3073 (TS:1150) 1 OF 1

F E D C B A
 F E D C B A
REV.NO DETAILS OF REVISION BY DATE

00 NEW RELEASE HRUSHIKESH 10-07-23

1
1

2 2

3 3

4 DATE
SIGN

HRUSHIKESH GANESH RATENDRA

4
Drawn By Checked By Approved By

UNLESS OTHERWISE STATED, ALL DIMENSIONS ARE ARE IN MM . DO NOT SCALE THE DRAWING. IF IN DOUBT, ASK. CONFIDENTIAL CUSTOMER: SCALE:
DEVIATION FOR OPEN DIMENSIONS (MED TO IS:2002) C 2001 THIS DRAWING AND ALL INFORMATION THEREON IS THE PROPERTY
CLASSIFICATION OF CHARACTERISTICS SURFACE ROUGHNESS SYMBOLS
OF iAi JOIN FLEX (I) PVT. LTD. AND MUST NOT BE COPIED TRANSMITTED OR PROJECT: SIZE: A1
GENERAL TOLERANCES FOR FABRICATION UNLESS OTERWISE STATED
GRD HRD & GRD
LINEAR DIMENSIONS & HOLE CENTERS 1
CRITICAL MAJOR NEW
N11 N9 N6 N3
N6 N6 REPRODUCED DIRECTLY OR INDIRECTLY WITHOUT iAi JOIN FLEX'S PERMISSION.
PIECES PARTS MACHINING ASSEMBLIES 0.15
APPLIES TO UPPER LIMIT 0-500 1 0-30 0.1 0-100 0.5
DRILLED HOLES UPTO Ø8 DESCRIPTION:
2 %OF OLD
OVER 500-1000 1.5 30-60 0.2 OVER 100-500 1 DRILLED HOLES OVER Ø8 Ø
APPLIES TO LOWER LIMIT OVER 1000-2000
2000 AND OVER
1.5
5
60-180
180-500
0.3
0.4
OVER 500-2000
2000 & OVER
1.5
3
ANGLES 1 ADM JOINFLEX INDIA PVT LTD DRG. NO. : SHEET
KEY INSTRUCTIONS ANGLES 1 500 & ABOVE 0.5 ANGLES 1 Ra ON MACHINED SURFACE 6.3
FOR OTHER : IS 3073 (TS:1150)

F E D C B A