Enquiry - Valve Plumbing

HEAT PUMP
a CI Wafer Type Butterfly Valve 100 mm Nos 8

b CI Dual Plate Check Valve 100 mm Nos 4
c Pressure Gauge with ball valve Nos 8
d Temperature Gauge Nos 8
c CI Y-Type Strainer 100 mm Nos 4
d Pressure Gauge with ball valve Nos 2
e Temperature Gauge Nos 2
a Bronze Globe Valve - 40 mm Nos 3
b Forged brass ball Valve - 25 mm Nos 6
Water Softening Plant
a Bronze Globe Valve - 40 mm Nos 3

b Forged brass ball Valve - 25 mm Nos 6
Upper Zone & Lower Zone

c Pressure Gauge Nos 8
d Temperature Gauge Nos 8
e Drain Valve - 15 mm Forged Brass Ball Valve Nos 8

f CI Wafer Type Butterfly Valve 100 mm Nos 6
g CI Dual Plate Check Valve 100 mm Nos 2
h Bronze Globe Valve 40 mm Nos 1
i Bronze Horizontal Check Valve 40 mm Nos 1
Cold water inlet

a CI Butterfly Valve 100 NB Nos 3
b CI wafer Dual Check Valve 100 NB Nos 3
Hot water outlet

c CI Butterfly Valve 100 NB Nos 3
d CI wafer Dual Check Valve 100 NB Nos 3
Hot Water inlet & Outlet (Primary Side)

e CI Butterfly Valve 100 NB Nos 6
Hot water Return

f CI Butterfly Valve 40 NB Nos 3
Drain Valve
g Bronze globe valve - 40 NB Nos 3
h Pressure Gauge Nos 3

i Temperature Gauge Nos 3
Supply of Temperature Controller with

j Nos 3
TIC/Temperature Sensor with RS485 port
k Supply of Bronze Safety Valve - 25 NB Nos 3

l Supply of Bronze Air Vent - 15 NB Nos 3
a Bronze Globe Valve 40 mm Nos 8

b Bronze Non Return Valve 40 mm Nos 4
Space Heating

b Pressure Gauge Nos 4
c Temperature Gauge Nos 4
d Drain Valve - 15 mm Forged Brass Ball Valve Nos 4
a CI Wafer Type Butterfly Valve 100mm Nos 4

Supply of Temperature Controller with
Nos 1
TIC/Temperature Sensor
2.05 Providing, fixing, jointing and testing, heavy quality cast

bronze / brass ball valves of approved make, including
flanges / unions, nuts, bolts, washers, etc. complete, as
approved by the Architect and Engineer-in-charge for water
supply lines of the following nominal bore (NB) size:
1) 50 mm no R.O
2) 40 mm no 39
3) 32 mm no 71
4) 25 mm no 37
5) 20 mm no 302
6) 15 mm no 276
2.06 Providing, fixing, jointing and testing, heavy quality

butterfly valve with rubber gasket, flanges / unions, nuts,
bolts, washers, etc. complete, as approved by the Architect
and Engineer-in-charge for water supply lines of the
following nominal bore (NB) size:
1) 150 mm no R.O
2) 125mm no R.O
3) 100 mm no 10
4) 80 mm no 13
5) 65 mm no 11
6) 50 mm no 27
2.07 Supply , installation ,testing & Commissioning Slow

closing motorised butterfly valve (with bypass
arrangment Consisting of 3 nos. Manual Butterfly
Valve ) rating PN 1.6 with float type sensors
suitable for 240 volts with working pressure
rating of not less than 5 kg/cm2 with control
panel and sensors to open valve when water
level is low in tanks and to close when water
level is high in water tanks including butterfly
valves, necessary 1.0 Sqm Wires /cables,
conduits, up to junction box etc. complete. (up to
15 mt qty approx.) .valve is compatible to BMS
System.
type : Wafer type
Operation : Electrcial Actuator based
body : S.G. Iron
Actuator Base : Carban Steel
disc : Stainless steel
Electrcial Panel : IP67 proptection
Body Lining : EPDM
1) 50 mm dia no R.O
2) 80 mm dia no 3
3) 100 mm dia no 5
2.08 Providing, fixing, jointing and testing, heavy quality gun
metal or brass non return valve confirming to IS 778, with
screwed / flanged ends, 16 kg/m2 of approved make, on
water supply lines of the following nominal bore (NB) size:
1) 150 mm no R.O
2) 125mm no R.O
3) 100 mm no 1
4) 80 mm no 2
5) 65 mm no 2
6) 50 mm no 8
7) 40 mm no 4
8) 32 mm no 18
9) 25 mm no 17
10) 20 mm no 8
11) 15 mm no 143
2.09 Providing, fixing and testing, heavy quality Pressure

reducing valves of approved make as approved,including
flanges / unions, nuts, bolts, washers, Pressure guages, etc.
complete by the Architect and Engineer-in-charge for water
supply lines of the following nominal bore (NB) size: The
upstream water pressure may be upto 7 kg/cm2g max. and
downstream pressure min. 1 kg/cm2g.
1) 100 mm no R.O
2) 80 mm no R.O
3) 65 mm no R.O
4) 50 mm no R.O
5) 40 mm no R.O
6) 32 mm no R.O
2.10 Providing and fixing, 15 mm. dia. GI hydrant, for

gardening, at required distance, with 25 mm. dia. wheel
valve / ball valve of approved make, as recommended or
equivalent and GI pipe piece to provide the hydrant, 300
no 10
mm. above dressed ground level, including excavation,
making connections with main lines, specials, if required etc.
complete, as directed. (Assumed)
2.12 Providing and fixing electronic type level indicator for

water tanks mounting in panel with level display, alarm
(level low or high), and manual reset for alarm, potential
free set point contacts etc. complete with electrical wiring to
no 16
probes and all accessories complete the work. Provision to
connect to the building Automation system or pump
controller through a suitable port.
2.13 Providing and fixing in position of approved quality
G.M. float valve with copper ball float and brass rods
of required length suitable for test pressure of 15Kg/sqcm
of the following sizes:
1) 65 mm no 16
2) 50 mm no R.O
3) 40 mm no R.O
4) 32 mm no R.O
2.14 Providing and fixing water meter station with direct

reading dial in KL with all integral parts of gun metal
or brass with neccesary fitting such as threaded pieces,
unions pressure guage and isolation cock, flanges piece
for future removal, flanges/unions complete with all
necessary testing charges and obtaining test cetificates
from municipal authorities.
1) 100 mm no 3
2) 80 mm no R.O
3) 65 mm no R.O
4) 50 mm no R.O
2.18 Providing and fixing GM Air release valve, double acting,

of approved make, having 2 chambers with ebonite ball,
small and large orifices with isolating stop screw down
valve, GM seats, high tensile brass spindle with cap,
conforming to standard water works pattern. flat faced and
drilled, complete of the following nominal bore (NB) size:
1) 25 mm no R.O
2) 15 mm no 24
2.19 Providing and fixing C.I. “Y” strainer (screwed / flanged)

with stainless steel fine wire mesh perforated sheet basket
with necessary flanged / unions nuts, bolts and washers
complete as required.
1) 200 mm dia. no R.O
3) 100 mm dia. no 3
4) 80 mm dia. no 1

Enquiry - Valve Plumbing

Uploaded by

Copyright:

Available Formats

Enquiry - Valve Plumbing

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Enquiry - Valve Plumbing

Uploaded by

Copyright:

Available Formats

HEAT PUMP

a CI Wafer Type Butterfly Valve 100 mm Nos 8

Water Softening Plant

a Bronze Globe Valve - 40 mm Nos 3

Upper Zone & Lower Zone

a CI Wafer Type Butterfly Valve 100 mm Nos 8

a CI Wafer Type Butterfly Valve 100 mm Nos 8

Cold water inlet

Hot water outlet

Hot Water inlet & Outlet (Primary Side)

Hot water Return

h Pressure Gauge Nos 3

Supply of Temperature Controller with

k Supply of Bronze Safety Valve - 25 NB Nos 3

a Bronze Globe Valve 40 mm Nos 8

a CI Wafer Type Butterfly Valve 125 mm Nos 4

a CI Wafer Type Butterfly Valve 100mm Nos 4

2.05 Providing, fixing, jointing and testing, heavy quality cast

2.06 Providing, fixing, jointing and testing, heavy quality

2.07 Supply , installation ,testing & Commissioning Slow

2.09 Providing, fixing and testing, heavy quality Pressure

2.10 Providing and fixing, 15 mm. dia. GI hydrant, for

2.12 Providing and fixing electronic type level indicator for

2.14 Providing and fixing water meter station with direct

2.18 Providing and fixing GM Air release valve, double acting,

2.19 Providing and fixing C.I. “Y” strainer (screwed / flanged)

You might also like