Micro System MCM277/05/12/98

Service
Service
Service

Service Manual COMPACT

DIGITAL AUDIO

From week 0913 onwards, ALI solution(decode IC) has been adopted
to replace ROHM solution(decode IC), accordingly new Main Board &
Display/MCU Board & AC Power Board, etc. were used to match with
new
. solution.

Please refer chapter 1 to 9 for sets produced before week 0913 and
chapter 10 & chapter 15 for changed contents for sets produced in or
after week 0913.

Ali solution starting S/N: EF2A0913000001.

CLASS 1
©
Copyright 2010 Philips Consumer Electronics B.V. Eindhoven, The Netherlands LASER PRODUCT
All rights reserved. No part of this publication may be reproduced, stored in a retrieval system or
transmitted, in any form or by any means, electronic, mechanical, photocopying, or otherwise
without the prior permission of Philips.

Published by SL1020 Service Audio Printed in The Netherlands Subject to modification GB 3141 785 32376

Version 1.6
 1-2

VERSION VARIATIONS

Type /Versions: MCM277

Service policy /05 /12 /55 /58 /61 /98

Board in used:
MAIN BOARD C C C
CD/MCU BOARD M M C
HEADPHONE JACK BOARD C C C
DISPLAY BOARD C C C
AC POWER BOARD C C C
KEY BOARD C C C
TUNER BOARD M M M

Type /Versions: MCM277

Features
Feature diffrence /05 /12 /98
in used:
Aux in / CDR in x x x
Line Out
Video Out
Surround Out
Subwoofer Out
Power Booster Out
Digital Out
Digital in
Matrix Surround
RDS x x
News x x
Dolby Pro Logic (DPL)
Incredible Surround
Karaoke Features
Voltage Selector x
ECO Power Standby (LCD Display Off) x x
USB Direct x x x x

* TIPS : C -- Component Lever Repair.

M -- Module Lever Repair
x -- Used
 1-3

SPECIFICATIONS

GENERAL:
Mains voltage : 127/240V -15%+10% Switchable for /98 Dynamic Bass Boost (DBB) : ON / OFF
120V ± 10% for /37 Input sensitivity
230V ± 10% for /05/12 Aux in (at 1kHz) : 500mV at 600 Ω
Mains frequency : 50/60Hz USB : Host
Clock accuracy : < 4 seconds per day Output sensitivity
Dimension centre unit :194(W)x269(H)x90(D) (mm) Headphone output at 32 Ω : 10mW ± 2dB (Max. vol.)

Power consumption COMPACT DISC:

Active : 20W Frequency response within ± 3dB : 125Hz - 16kHz
Standby : < 5.5W (DEMO mode) Output level (in Vrms) : 500mV, Zout = 100Ω
ECO Power Standby : < 0.5W for /05/12/37 Signal/Noise ratio (unw.) : > 65dB
Signal/Noise ratio (A-weighted) : > 76dB
Distortion at 1kHz : < 0.02%
Channel unbalance (-40dB) : < ±2dB
TUNER: Channel separation at 1kHz : > 30dB
FM Emphasis : 15/50 µS (switched
Tuning range : 87.5-108MHz automatically by CD10)
Grid : 50kHz for /98/12/05 THD Noise(1kHz,500mW) : < 1.0%
100kHz for /98/55/37 Volume attenuation(1kHz) : > 60dB
IF frequency : 10.7MHz ± 20kHz MP3 CD WMA:
Aerial input : 75 Ω coaxial /05/12/98 MP3 : MPEG 1 (ISO/IEC 11172-3)
300 Ω for /37 Layer3
Sensitivity at 26dB S/N : < 22µf MP3-CD Bit Rate : 8-320 kbps
Selectivity at 300kHz bandwidth : > 25dB WMA-CD Bit Rate : 64-192 kbps
Image rejection : > 25dB [> 75dB] Sampling Rate : 8, 11.025, 12, 16, 22.05,
IF rejection : > 60B [> 80dB] 24, 32, 44.1, 48 kHz
Distortion at RF=1mV, dev. 75kHz : < 3% Format : ISO9660, Joliet,UDF
-3dB Limiting point : < 23.5dBf ID3 : V1 tag/V2 2.0/V2 3.0
Crosstalk at RF=1mV, dev. 40kHz : > 18dB
Language Support : English

MW
Tuning range : 531-1602kHz for /05/12/55/98
530-1700kHz for /37/98
Grid : 9kHz for /05/12/55/98
10kHz for /37/98 [....] Values indicated are for /05/12 only.
IF frequency : 450kHz ± 1kHz
Aerial input : Frame aerial 18.1µH
Sensitivity at 26dB S/N : < 4.4mV/M
Selectivity at 300kHz bandwidth : > 18dB
IF rejection : > 45dB
Image rejection : > 28dB
Distortion at RF=50mV, M=80% : < 5%

AMPLIFIER:
Output power
L&R : 2 x 5.0W (4Ω, 1kHz, 10% THD)
: 2 x 4.5W (4Ω, 1kHz, 10% THD) /98
: 2 x 4.5W (FTC Power, 4Ω, 1kHz, 10% THD
63Hz-12.5kHz) /37
Frequency response within -3dB : 50Hz-16kHz
Digital Sound Control (DSC) : Jazz / Rock / Pop / Classic
 1-4

MEASUREMENT SETUP

Tuner FM

Bandpass
DUT 250Hz-15kHz LF Voltmeter
e.g. 7122 707 48001 e.g. PM2534
RF Generator
e.g. PM5326
Ri=50

S/N and distortion meter

e.g. Sound Technology ST1700B

Use a bandpass filter to eliminate hum (50Hz, 100Hz) and disturbance from the pilottone (19kHz, 38kHz).

Tuner AM (MW,LW )
Bandpass
250Hz-15kHz LF Voltmeter
DUT e.g. 7122 707 48001 e.g. PM2534

RF Generator
e.g. PM5326
S/N and distortion meter
e.g. Sound Technology ST1700B
Ri=50

Frame aerial
e.g. 7122 707 89001

To avoid atmospheric interference all AM-measurements have to be carried out in a Faraday´s cage.
Use a bandpass filter (or at least a high pass filter with 250Hz) to eliminate hum (50Hz, 100Hz).

CD
Use Audio Signal Disc SBC429 4822 397 30184 (replaces test disc 3)

DUT
L

S/N and distortion meter

e.g. Sound Technology ST1700B

LEVEL METER
e.g. Sennheiser UPM550
with FF-filter
 1-5

SERVICE AIDS

GB WARNING ESD
All ICs and many other semi-conductors are
susceptible to electrostatic discharges (ESD).
Careless handling during repair can reduce life
drastically.
When repairing, make sure that you are
connected with the same potential as the mass
of the set via a wrist wrap with resistance.
Keep components and tools also at this
potential.

GB
Safety regulations require that the set be restored to its original CLASS 1
condition and that parts which are identical with those specified,
be used LASER PRODUCT
Safety components are marked by the symbol ! .

Lead free
 1-6

INSTRUCTIONS ON CD PLAYABILITY

Customer complaint
"CD related problem"

Set remains closed!

1
check playability

playability N
ok ?

Y 3
For flap loaders (= access to CD drive possible)
"fast" lens cleaning cleaning method 4 is recommended

check playability

playability N
ok ?

Play a CD
for at least 10 minutes

check playability

playability N
ok ?

add Info for customer Exchange CDM

"SET OK" 2

return set

1 - 4 For description - see following pages

 1-7

INSTRUCTIONS ON CD PLAYABILITY

1 4
PLAYABILITY CHECK LIQUID LENS CLEANING
Before touching the lens it is advised to clean the
surface of the lens by blowing clean air over it.
For sets which are compatible with CD-RW discs
This to avoid that little particles make scratches on
use CD-RW Printed Audio Disc ....................7104 099 96611
the lens.
TR 3 (Fingerprint)
TR 8 (600µ Black dot) maximum at 01:00
Because the material of the lens is synthetic and coated
• playback of these two tracks without audible disturbance with a special anti-reflectivity layer, cleaning must be done
playing time for: Fingerprint 10seconds with a non-aggressive cleaning fluid. It is advised to use
Black dot from 00:50 to 01:10 “Cleaning Solvent
• jump forward/backward (search) within a reasonable time

The actuator is a very precise mechanical component and

may not be damaged in order to guarantee its full function.
For all other sets Clean the lens gently (don’t press too hard) with a soft and
use CD-DA SBC 444A..................................4822 397 30245 clean cotton bud moistened with the special lens cleaner.
TR 14 (600µ Black dot) maximum at 01:15
TR 19 (Fingerprint) The direction of cleaning must be in the way as indicated in
TR 10 (1000µ wedge) the picture below.

• playback of all these tracks without audible disturbance

playing time for: 1000µ wedge 10seconds
Fingerprint 10seconds
Black dot from 01:05 to 01:25
• jump forward/backward (search) within a reasonable time

2
CUSTOMER INFORMATION

It is proposed to add an addendum sheet to the set which

informs the customer that the set has been checked
carefully - but no fault was found.
The problem was obviously caused by a scratched, dirty or
copy-protected CD. In case problems remain, the customer
is requested to contact the workshop directly.
The lens cleaning (method 3) should be mentioned in the
addendum sheet.

The final wording in national language as well as the printing

is under responsibility of the Regional Service Organizations.
Preparation

Using the remote control Setting the clock 8

After connecting MCM275 to the power supply,
IMPORTANT!
set the clock first. 1
– Remove the
1 Press and hold STANDBY-ON/ ECO 7
protective plastic tab 2
POWER to switch the set to Standby mode
before using the
The display shows the set time
remote control.
-- --:-- -- flashes by default if you have not set
– Always point the the clock
remote control directly 2 In the standby mode, press and hold DISPLAY/
towards IR area. CLOCK on the remote control
SET CLOCK scrolls on the display
Notes for remote control: 24 HR or 12 HR appears for the initial
– First select the source you wish to clock setting. To select 24-hour clock or
control by pressing one of the source select 12-hour clock,
keys on the remote control (for example On the remote control, press VOLUME +/-
PREPARATIONS AND CONTROLS

CD,TUNER). once or more (or turn VOLUME on the

– Then select the desired function (for set)
example ÉÅ, í, ë). On the remote control, press DISPLAY/ 6
CLOCK to confirm
To replace the remote controls’ The hours digits start flashing
battery 3 Hold down or press VOLUME +/- repeatedly
to set the hours (or turn VOLUME on the
3
1-8

set) 5
1 Press and hold 1 as indicated.
4 Press DISPLAY/CLOCK to confirm 4
2 Simultaneously, pull the battery tray at 4.
The minutes digits start flashing
3 Remove the old battery and put a new CR2025 5 Hold down or press VOLUME +/- repeatedly
battery in place. to set the minutes (or turn VOLUME on the
4 Put back the battery tray. set)
6 Press DISPLAY/CLOCK to confirm
– To exit without storing the clock setting press
STOP 9
2
Helpful hints:
9
1 – The clock setting will be erased when the system 0
is disconnected from the power supply. !
3 – The set will exit from the clock setting mode if
CR 2
02

LI
TH
IUM no button is pressed within 90 seconds.
@
– To set the clock automatically by using a time %
signal which is broadcast together with the RDS
signal see chapter RDS: Automatic clock
#
setting via RDS.
$
CAUTION! /

– Remove the battery if it is exhausted

USB

or will not be used for a long time.

– Batteries contain chemical substances,
so they should be disposed of properly.
Controls Controls
AUX
1 STANDBY-ON/ ECO POWER 0 DBB (Dynamic Bass Boost) – selects the audio input from an additional
– turns the bass enhancement on/off
Remote control
– press briefly to switch the set on or off (standby/ connected appliance
ECO POWER); ! DSC (Digital Sound Control) – In standby or Eco Power mode:: switches the
– In standby or Eco Power mode: press and /
– selects predefined sound settings: ROCK, set on and selects the audio input from an
hold to toggle between Standby and ECO JAZZ, POP, CLASSIC % 1 additional connected appliance
USB
POWER mode (power-saving mode)
@ PROGRAM 2 3 VOLUME +/-
– Red indicator: lights up red when the set is
– CD/USB: programs tracks – adjusts the volume level
switched to ECO POWER mode 3
– Tuner: programs preset radio stations – Clock/Timer: adjusts the hours and minutes
2 SOURCE $
# STOP 4 TIMER
– selects sound source CD, USB,TUNER or
– CD/USB: stops playback; erase a program 4 – displays the timer setting
AUX #
$ AUX-IN – switches the timer on/off
– In standby or Eco Power mode: switches the @ 5
– connects to the AUDIO OUT jack on the – enters the timer setting mode (press and hold
set on and selects sound source CD, USB,
external appliance ! 6 for more than 2 seconds)
TUNER or AUX
% 0 7 5 SLEEP
3 IR – set the sleep timer
– jack for the external USB mass storage device
PREPARATIONS AND CONTROLS

– sensor for the infrared remote control 9 8

Helpful hints: Always point the remote control
6 MUTE
– switches the sound off temporarily
towards this sensor.
7 RDS/NEWS
4 PUSH OPEN
– push to unfold or fold the control panel Notes for remote control: – Tuner: selects RDS (Radio Data System)
– First select the source you wish to information
5 CD OPEN • CLOSE 0
– opens/closes the CD door control by pressing one of the source select – CD/USB/AUX: activates/deactivates news
1-9

keys on the remote control (for example

6 CD door 8 SHUFFLE
CD,TUNER).
7 VOLUME – Then select the desired function (for – selects random playback
– adjusts the volume level example ÉÅ, í, ë). 9 REPEAT
– Clock/Timer: adjusts the hours and minutes – selects continuous playback
1 B
8n – press briefly to switch the set on or off (standby/ 0 DSC (Digital Sound Control)
– 3.5 mm headphone socket ECO POWER); – selects predefined sound settings: ROCK,
Helpful hints: – In standby or Eco Power mode: press and JAZZ, POP, CLASSIC
– Adjust the volume to a moderate level hold to toggle between Standby and ECO
before you plug in the headphones. POWER mode (power-saving mode)
! DBB (Dynamic Bass Boost)
Source buttons – turns the bass enhancement on/off
– Connecting headphones will switch off the 2
speakers. USB @ PROGRAM
– selects USB source – CD/USB: programs tracks
9 ALBUM/ PRESET + /- – Tuner: programs preset radio stations
– CD/USB: selects albums (for MP3/WMA only) – In standby or Eco Power mode:: switches the
– TUNER: selects a preset radio station set on and selects USB source. # DISPLAY/CLOCK
CD – Clock: - displays the set time
4 / ¢ - In standby mode: enters the clock
– selects CD source
– CD/USB: skips or searches CD tracks/titles setting mode (press and hold for more
– In standby or Eco Power mode:: switches the
backwards/forwards than 2 seconds)
set on and selects CD source.
– Tuner: tunes to radio stations – TUNER/Audio CD: switches between clock
TUNER
6 – selects TUNER source and toggles between the display and playback
– CD/USB: starts or pauses playback wavebands: FM and MW display
– MP3/WMA files: displays disc information
– In standby or Eco Power mode:: switches the
during playback
set on and selects TUNER source
Controls Installation Installation

$4 / ¢ Placing MCM275
– CD/USB: skips or searches CD tracks
backwards/forwards With the detachable stand and by-packed wall
– Tuner: tunes to radio stations mounting kit , MCM275 allows you to place it in FM wire
two ways: on desktops with stand or on MW loop
ALBUM/ PRESET 3 / 4 antenna antenna
walls without stand.
– CD/USB: selects the next/previous album (for
MP3/WMA only) Mounting stand onto the set
– TUNER: selects a preset radio station
MCM275 is equipped with a stand. To mount
ÉÅ the stand onto the set,
– CD/USB: starts or pauses playback 1 Put MCM275 on a flat and firm surface, rear side Speaker Speaker
9 facing up (right) (left)
– CD/USB: stops playback; erase a program 2 As shown, align the stand to the slots at set’s
CONTROLS & INSTALLATIONS

% OPEN • CLOSEç bottom, 4 FRONT facing down

– opens/closes the CD door

PRESS PRESS

FRONT
FRONT

AC power cord
1-10

3 Push the stand down into the slots Rear connections

When the stand is in place, you will hear a
click Warning:
– Never make or change connections with
the mains supply switched on.
– Install your set near the AC outlet and
where the AC power plug can be reached
easily.

A Speaker connections
Use the supplied speakers only. Using other B Antenna connections
speakers can damage the set or the sound MW antenna
quality will be negatively affected.
1 Assemble the loop antenna as shown:
Connect the cable of the left speaker to LEFT
Mounting MCM275 onto walls (red and black) and the cable of the right
speaker to RIGHT (red and black) as follows:
See Appendix: How to mount your a. Press the clip of the red terminal and fully
MCM275 onto walls to learn more about insert the stripped portion of the colored (or
wall mounting. marked) speaker cable into the socket, then
release the clip
b. Press the clip of the black terminal and fully
insert the stripped portion of the black (or
unmarked) speaker cable into the socket, then
release the clip
Installation Installation
Or 2 Move the antenna in different positions for
Insert the loop antenna into the slot on the set optimal reception (as far away as possible from Connecting a non-USB device Using AC power
the TV, VCR or other radiation sources)
It is possible to use an additional appliance, e.g. 1 Make sure all the connections have been made
3 Fix the antenna’s end to the wall
TV, VCR or CD recorder with the set. On before switching on the power supply
Connecting an additional MCM275, you can playback music from an
appliance external source. 2 Connect the AC power cord to the wall socket.
Connecting a USB device or memory 1 Follow the Step 1 under Connecting a USB This switches on the power supply
card device or memory card
Insert one plug of the audio cable (not supplied) When MCM275 is switched to standby, it is still
By connecting a USB mass storage device 2
to the socket AUX IN on the set ‘s foldable consuming some power. To disconnect the
(including USB flash memory, USB flash players
control panel system from the power supply completely,
or memory cards) to the Hi-Fi system, you can
enjoy the device’s stored music through the
remove the power plug from the wall
2 Fit the plug of the loop antenna to AM (MW) 3 Connect the other end of the audio cable to the
powerful speakers of Hi-Fi system. socket.
ANTENNA as shown below AUDIO OUT terminal of the additional
1 Check you have unfolded the control panel appliance
The type plate is located on the rear of the
CONTROLS & INSTALLATIONS

3 Adjust the position of the antenna for optimal

reception (as far away as possible from the TV, set.
VCR or other radiation sources)
For users in the U.K.: please follow the
instructions.

Warning!
AM
ANTENNA To avoid overheating of the system, a safety
circuit has been built in. Therefore, your
1-11

system may switch to Standby mode

automatically under extreme conditions. If
2 Insert the USB device’s USB plug into the socket this happens, let the system cool down
FM antenna on the set ‘s foldable control panel before reusing it (not available for all versions).
The wire antenna supplied can only be used to
receive nearby stations. For better reception we This product complies with the radio
recommend using a cable antenna system or an 4 Select AUX mode on the set interference requirements of the European
outdoor antenna. Community.
1 Extend the wire antenna and fit it to FM
ANTENNA as shown below Helpful hints: CAUTION
– Always refer to the owner’s manual of other
equipment for complete connection. Visible and invisible laser radiation. If the
or cover is open, do not look at the beam.
for the devices with USB cable: High voltage! Do not open. You run the risk
a. Insert one plug of the USB cable (not
of getting an electric shock.
supplied) to the socket on the set ‘s
The machine does not contain any user-
foldable control panel
serviceable parts.
b. Inser t the other plug of the USB cable to the
USB output terminal of the USB device Modification of the product could result in
or hazardous radiation of EMC or other
for the memory card: unsafe operation.
a. Insert the memory card into a card reader
(not supplied)
Note: If you are using a cable antenna system or b. Use a USB cable (not supplied) to connect
an outdoor antenna, fit the antenna plug, instead of the card reader to the socket
the wire antenna, to FM ANTENNA . on the set ‘s foldable control panel
 Troubleshooting Troubleshooting

WARNING The remote control does not function Select the source (CD or TUNER, for example)
Under no circumstances should you try to repair the system yourself, as this will invalidate the properly. before pressing the function button (ÉÅ,í,

English
warranty. Do not open the system as there is a risk of electric shock. ë).
Reduce the distance between the remote
If a fault occurs, first check the points listed below before taking the system for repair. If you control and the system.
are unable to remedy a problem by following these hints, consult your dealer or Philips for Insert the battery with its polarities
help. (+/– signs) aligned as indicated.
Replace the battery.
Problem Solution Point the remote control directly toward
TROUBLESHOOTING

IR sensor on the front of the system.

“NO DISC” is displayed. Insert a disc.
Wait until the moisture condensation at the lens The timer is not working. Check the set is switched off
has cleared. Set the clock correctly.
Replace or clean the disc, see “Maintenance”. Press TIMER to switch on the timer.
Use a finalised CD-RW or a correct MP3/WMA
-CD format disc.
The Clock/Timer setting is erased. Power has been interrupted or the power cord
has been disconnected. Reset the clock/timer.
Some files on the USB device are not Check if the number of folders exceeds 99 or
displayed. the number of titles exceeds 999

Radio reception is poor. If the signal is too weak, adjust the antenna or
connect an external antenna for better
1-12

reception.
Increase the distance between the Micro HiFi
System and your TV or VCR.

The system does not react when buttons Remove and reconnect the AC power plug and
are pressed. switch on the system again.

Sound cannot be heard or is of poor Adjust the volume.

quality. Disconnect the headphones.
Check that the speakers are connected correctly.
Check if the stripped speaker wire is clamped.
Make sure the MP3-CD was recorded within
32~256 kbps bit rate with sampling frequencies
at 48 kHz, 44.1 kHz or 32 kHz.

The left and right sound outputs are Check the speaker connections and location.
reversed.
 2-1 2-1

DISMANTLING INSTRUCTIONS
Dismantling the Rear Portion and PCBs Dismantling the Rear Portion and PCBs

1) Press the 2 juts and pull out the Stand as shown in figure
1. 5) Loosen 2 screws E to remove the Bracket Jack Board as
shown in Figure 4.

6) Loosen 3 screws F to remove the Main Board as shown

in figure 5.

Figure 1

Figure 2 Figure 4

2) Loosen 5 screws A and 6 screws B to remove the Rear

Cabinet as shown in figure 2. Figure 5

3) Loosen 3 screws C to remove the SP & ANT Jack Board

as shown in figure 3.

Dismantling of the Display Lens & the Volume knob

4) Loosen 5 screws D to remove the Power Module as
shown in figure 3. 2) Place two small screw drivers in between the front cabinet
1) Use a flat head screw driver to give a push in the direction
& knob to give more leverage in pulling out the Volume
as shown in figure 6.
Knob as shown in figure 7.

Figure 7
Figure 6
Figure 3
 2-2 2-2

Dismantling of the CD Module & CD Door Carrier

Service pos A
1) Loosen 5 screws J mounting the Key Board to the Front
Cabinet to remove the Key Board as shown in figure 8.

2) Loosen 4 screws H and 3 screws G to CD Module as

shown in figure 8.

3) Loosen 2 screws I to remove the Servo Motor Mechanism

as shown in figure 8.

4) Loosen 4 screws K to remove the Right CD Door Carrier

and 4 screws L to remove the Left CD Door Carrier as
shown in figure 9.

Service pos B

Figure 8

Figure 9

Note: After re-assembly, it is very important to ensure all

wires are routed properly to ensure that they do not
touch/obstruct all moving parts.
 3-1 3-1

SERVICE TEST PROGRAM

To enter Service * Door switch is ignored → CD door can be opened.

Testprogram hold
PLAY & Door Open/Close
buttons depressed while
plugging mainscord in.

Display shows the

MCU version V refers to Version
"MCU-Vyy"
(Main menu) yy refers to Software version number of the uProcessor
(counting up from 01 to 99)

KEY DISPLAY ADC

TEST TEST TEST
NEXT N N N
PREV DBB
Button pressed? Button pressed? Button pressed?

Y Y Y

Display shows Display shows Figure 1 Display shows "ADC0 Value"

Table 1 All display flags on. for ADC0
(Input Line - For key scanning)

9 N Figure 1 PREV
N
DBB N
Button pressed? Button pressed?
Button pressed?

Y Y
Y

Display shows alternate

segment display from SEG0 Display shows "ADC1 Value"
to SEG64. for ADC1
(Input Line - ioNTC Heat
detection for transformer)

N
PREV N
Button pressed? DBB
Various Button pressed?
other Tests
Y
Y

TEST Activated with ACTION No Display shows

Display shows "ADC2 Value"
for ADC2
EEPROM CLEAR A test pattern will be sent to the EEPROM.
PROGRAM (Input Line - Rotary volume)
"EEP CLR" is displayed while the erase processing.
9 to Exit Caution! All presets from the customer will be lost!!
9 N
LEAVE SERVICE Disconnect Button pressed?
TEST PROGRAM mains cord N
DBB
Button pressed?
Y

Display shows "ADC3 Value"

for ADC3
Key test table (Input Line - Door switch status)

KeyNr Set key KeyNr Set key KeyNr Set key

0 CD 10 RDS 20 PROGRAM
1 AUX 11 21 SHUFFLE DBB N
Button pressed?
2 TUNER 12 CLOCK/DISPLAY 22 NULL
3 SOURCE 13 ALBUM + 23 SLEEP
Y
4 STANDBY/ON 14 ALBUM - 24 TIMER
5 OPEN/CLOSE 15 SKIP PREV 25 DBB Display shows "ADC4 Value"
6 VOLUME DOWN 16 SKIP NEXT 26 DSC for ADC4
(Input Line - Version detection)
7 VOLUME UP 17 NULL 27 MUTE
8 NULL 18 NULL 28 USB
9 NULL 19 REPEAT
ADC Test is used for checking the 9 N
ADC inputs to the microprocessor. Button pressed?

Table 1 The display shows an ADC value

between 0 and 255 for an input Y
signal between 0 and 5V.
 4-1 4-1

SET BLOCK DIAGRAM

BR24L02F-WE2
IC104 IC701
IC801

E01J
468D
UR11 IC103 IC601
IC401

DAYANG M93BGP-BF CF91D

IC100 IC501
IC300 AP34063A
IC102 IC301

BR24L02F-WE2
IC504
W27C512-45Z
IC302
 5-1 5-1

SET WIRING DIAGRAM

 6-1 6-1

BLOCK DIAGRAM - RDS/RBDS PRE-PROCESSOR

SAA6588T

BLOCK DIAGRAM

I2C-BUS
multi-path
available

output
output
pause
data

11 PSWN
2 MPTH
8 DAVN

MGK535
9 SDA

10 SCL
100 nF
MAIN BOARD

C9

MAD
12
I2C-BUS SLAVE
TRANSCEIVER
VDDD

INTERFACE
RDS/RDBS

REGISTER
DECODER
7

VSSD
6
5 V

82 pF
OSCO
4

1 k"

C5
R1
4
SIGNAL QUALITY
DEMODULATOR

OSCILLATOR
AND CLOCK
DETECTOR
RDS/RDBS

n = 1 to 4
4.332
MHz
Q1

n h
4

OSCI
5

C4
47 pF
470
R4

k"
MRO
1

100
C6

nF
COMPARATOR

TCON
MULTI-PATH
DETECTOR
SAA6588
CLOCKED

CONTROL
TEST

3
TABLE OF CONTENTS

CIN
19
Internal IC Diagram ............................................... 6-1 to 6-5

560 pF
Main Board(5757) Layout Top View ................................ 6-6

C10

2.2 嘕F
Main Board(5757) Layout Bottom View .......................... 6-7

18

Vref

C7
Circuit Diagram - Main Board(5757) ............................... 6-8

17
SCOUT

AND RESET
BAND-PASS

DETECTOR
8th ORDER

SUPPLY
POWER
PAUSE
Main Board(5762) Layout Top View ................................ 6-9

57 kHz

VSSA
Main Board(5762) Layout Bottom View ........................ 6-10

15
Circuit Diagram - Main Board(5762) ............................. 6-11
HP Jack Board ............................................................... 6-12

LVIN 20
MPX 16

AFIN 13

VDDA 14
Electrical Parts List ........................................................ 6-13

10
k"
R2
0.47 嘕F

0.47 嘕F
330 pF

10
k"

C8
100 nF
2.2 nF
R3

C11
multiplex C1

C2

inputs C3

input
level

5 V
audio
input
 6-2 6-2

PIN DESCRIPTION - RDS/RBDS PRE-PROCESSOR BLOCK DIAGRAM - POWER AMPLIFIER

SAA6588T TDA1517

BLOCK DIAGRAM

PINNING

SYMBOL PIN DESCRIPTION SYMBOL PIN DESCRIPTION

MRO 1 mXOWLSDWKUHFWL¿HURXWSXW PSWN 11 pause sZLWFKRXWSXW DFWLve LOW)
MPTH 2 mXOWLSDWKGHWHFWRURXWSXW MAD 12 slavHDGGUHVV /6% LQSXW
non-inverting 1 mute switch Cm
TCON 3 WHVWFRQWUROLQSXWSLQ AFIN 13 DXGLRVLJQDOLQSXW input 1
60
OSCO 4 RVFLOODWRURXWSXW VDDA 14 DQDORJVXSSO\vROWDJH 5 V) kŸ
OSCI 5 RVFLOODWRULQSXW VSSA 15 DQDORJgURXQG 0 V) 4
output 1
VA
VSSD 6 digital gURXQG 0 V) MPX 16 multiple[LQSXWVLJQDO
2
VDDD 7 digital supply vROWDJH 5 V) Vref 17 refHUHQFHvROWDJHRXWSXW kŸ
DAVN 8 data availabOHRXWSXW DFWLve LOW) SCOUT 18 EDQGSDVV¿OWHURXWSXW 18 kŸ power stage
SDA 9 I2C-bus serial data I/O CIN 19 FRPSDrDWRULQSXW
SCL 10 I2C-bus serLDOFORcNLQSXW LVIN 20 levHOLQSXW VP

8 mute/stand-by
stand-by switch input
switch
stand-by
reference
VA voltage

15 kŸ

x1
mute
supply voltage 3 switch
ripple rejection
MRO 1 20 LVIN 15 kŸ
output
mute
MPTH 2 19 CIN reference
voltage
TDA1517
TCON 3 18 SCOUT 18 kŸ

OSCO 4 17 Vref

OSCI 5 16 MPX 2
kŸ
SAA6588T
VSSD 6 15 VSSA VA 6
non-inverting output 2
9
input 2
VDDD 7 14 VDDA 60
kŸ
DAVN 8 13 AFIN mute switch Cm
input power stage
SDA 9 12 MAD reference
voltage signal power
ground ground
SCL 10 11 PSWN 2 7 5 (substrate)
MLC351
MGK534
SGND VP PGND
 VP
M/SS
OUT2
OUT1

" INV2
" INV1

SVRR

PGND
SGND
PINNING
TDA1517

handbook, halfpage
SYMBOL

SOT352-1.
INV2
M/SS
VP
OUT2
PGND
OUT1
SVRR
SGND
INV1

4
3

9
8
7
6
5
2
1

TDA1517

MLC352
9
8
7
6
5
4
3
2
1
PIN

Pin configuration for SOT110-1 and

PIN DESCRIPTION - POWER AMPLIFIER
6-3

output 2
output 1
signal ground

power ground

supply voltage

non-inver ting input 2

non-inver ting input 1

mute/standby switch input

supply voltage ripple rejection output
DESCRIPTION

.This text is here in

TEA5757

FM-IFI1 FM-IFI2
FM-RFO FMOSC FM-MIXER FM-IFO1 IFGND FMDEM FSI
BLOCK DIAGRAM

3 5 39 37 35 33 17 18 21

43 16
FM-RFI FM FM FM FM FM FM PILOT PILFIL
42 FRONT-END OSCILLATOR MIXER IF1 IF2 DETECTOR DETECTOR 24
RFGND MO/ST
28 19 kHz
DATA
27 12
BUS-CLOCK
29 LFI
WRITE-ENABLE PLL 9
VCO
VSTAB(A) 38 STATUS AM/FM
VSTAB(B) 34 REGISTER INDICATOR 38 kHz
VCC1 7 STABILIZER SHIFT REGISTER
23 DECODER
BLOCK DIAGRAM - SELF TUNED RADIO

VDDD
1
RIPPLE
up IN-LOCK stereo
LAST-STATION down DETECTOR 14
AFLO
6-3

MEMORY level
PRESCALER MATRIX
AFRO
15
stereo mono
PROGRAMMABLE SEQUENTIAL CHARGE
MULTIPLEXER SDS
COUNTER CIRCUIT PUMP 13
MUTE
FM MUTE
level
hard mute
25
XTAL CRYSTAL WINDOW AM
26 OSCILLATOR DETECTOR
DGND AFC TEA5757;
TEA5759
31
P1 19
30 AFC(n)
P0 20
AFC(p)
32
AFC

2 AM AM AM AM AM V/I
AM-RFI AGC
FRONT-END OSCILLATOR MIXER IF DETECTOR CONVERTER

6 40 41 36 44 8 22 10 11 4 MHA111

AMOSC AM-MIXER AM-IFI/O2 AGC TUNE AFO MPXI RFGND

AM-IFI1 VCC2
 6-4 6-4

PIN DESCRIPTION - SELF TUNED RADIO PIN DESCRIPTION - SELF TUNED RADIO
TEA5757 TEA5757

PINNING SYMBOL PIN DESCRIPTION

SYMBOL PIN DESCRIPTION AM-IFI1 41 IFT or ceramic ¿lter input (input impedance typical 3 k" )
RIPPLE 1 ripple capacitor input RFGND 42 FMRF ground
AM-RFI 2 AMRF input FM-RFI 43 FMRF aerial input (input impedance typical 40 " )
FM-RFO 3 parallel tuned FMRF circuit to ground AGC 44 AGC capacitor input
RFGND 4 RF ground and substrate
FMOSC 5 parallel tuned FM-oscillator circuit to ground
AMOSC 6 parallel tuned AM-oscillator circuit to ground
VCC1 7 supply voltage
TUNE 8 tuning current output
VCO 9 voltage controlled oscillator input
AFO 10 AM/FM AF output (output impedance typical 5 kŸ)
MPXI 11 stereo decoder input (input impedance typical 150 kŸ)

40 AM-MIXER

39 FM-MIXER
LF I 12 loop-¿lter input

38 VSTAB(A)

36 AM-IFI/O2

34 VSTAB(B)
35 FM-IFO1
42 RFGND

41 AM-IFI1

37 FM-IFI1
43 FM-RFI
MUTE 13 mute input

44 AGC
AFLO 14 left channel output (output impedance typical 4.3 kŸ)
AFRO 15 right channel output (output impedance typical 4.3 kŸ)
PILFIL 16 pilot detector ¿lter input
RIPPLE 1 33 FM-IFI2
IFGND 17 ground of IF, detector and MPX stage
AM-RFI 2 32 AFC
FMDEM 18 ceramic discriminator input
FM-RFO 3 31 P1
AFC(n) 19 AFC negative output
AFC(p) 20 AFC positive output RFGND 4 30 P0

FSI 21 ¿eld-strength indicator FMOSC 5 29 WRITE-ENABLE

TEA5757H
VCC2 22 supply voltage for tuning AMOSC 6 TEA5759H 28 DATA
VDDD 23 digital supply voltage VCC1 7 27 BUS-CLOCK
MO/ST 24 mono/stereo and tuning indication output
TUNE 8 26 DGND
XTAL 25 crystal input
VCO 9 25 XTAL
DGND 26 digital ground
BUS-CLOCK 27 bus-clock input AFO 10 24 MO/ST

DATA 28 bus data input/output MPXI 11 23 VDDD

WRITE-ENABLE 29 bus write-enable input

LFI 12

MUTE 13

AFLO 14

AFRO 15

PILFIL 16

IFGND 17

FMDEM 18

AFC(n) 19

AFC(p) 20

FSI 21

VCC2 22
MHA112

P0 30 programmable output port (P0)

P1 31 programmable output port (P1)
AFC 32 450 kHz LC-circuit
FM-IFI2 33 FMIF input 2 (input impedance typical 330 Ÿ)
VSTAB(B) 34 internal stabilized supply voltage (B)
FM-IFO1 35 FMIF output 1 (output impedance typical 330 Ÿ)
AM-IFI/O2 36 input/output to IF-Tank (IFT); output: current source
FM-IFI1 37 FMIF input 1 (input impedance typical 330 Ÿ)
VSTAB(A) 38 internal stabilized supply voltage (A)
FM-MIXER 39 FHUDPLF¿OWHURXWSXW RXWSXWLPSHGDQFHW\SLFDO Ÿ) Pin configuration.
AM-MIXER 40 open-collector output to IFT
 6-5 6-5

BLOCK DIAGRAM - SELF TUNED RADIO PIN DESCRIPTION - SELF TUNED RADIO
TEA5762 (FOR /12/05) TEA5762 (FOR /12/05)

PINNING

SYMBOL PIN DESCRIPTION

MO/ST
RIPPLE 1 ripple capacitor input

AFC(n)
AFC(p)
PILFIL

MUTE
AFRO
AFLO
VCO

AFC
LFI

MBE815
AM-RFI 2 AMRF input
RFGND 3 RF ground and substrate
CGND 4 counter ground

RFGND
9
16

24

12

14

15

13

19
20
32
COUNTI 5 counter input

3
stereo

mono

MUTE

CONVERTER
DETECTOR

DECODER
AMOSC 6 parallel tuned AM-oscillator circuit to ground

MATRIX
PILOT

11

MPXI
PLL

V/I
VCC1 7 supply voltage

stereo
19 kHz

38 kHz

SDS
TUNE 8 tuning output current

TEA5762

RFGND
42
level
VCO 9 voltage controlled oscillator input
AFO 10 AM/FM AF output (output impedance typical 5 kŸ)

AFO
22 10
MPXI 11 stereo decoder input (input impedance typical 150 kŸ)
FSI

VCC2
21

LFI 12 loop ¿lter input

8
IFGND FMDEM

TUNE
DETECTOR

MUTE 13 mute input

18

FM

AFLO 14 left channel output (output impedance typical 4.3 kŸ)

DETECTOR
INDICATOR

down DETECTOR

CHARGE
17

IN-LOCK
AM/FM

AFRO 15 right channel output (output impedance typical 4.3 kŸ)

PUMP

AFC

AM
PILFIL 16 pilot detector ¿lter input
hard mute

30
IFGND 17 ground of IF, detector and MPX stage

P1 P0
FM
IF2

level
up

FMDEM 18 ceramic discriminator input

31
AGC AFC(n) 19 AFC negative output

AGC
CLOCK

FM SEQUENTIAL
27
BUS-

AFC(p) 20 AFC positive output

REGISTER

44
CIRCUIT
STATUS

FSI 21 ¿eld strength indicator

28
DATA

AM-IFI/O2
VCC2 22 supply voltage for tuning
AM
IF
ENABLE
WRITE-

36
29

AM

AM-IFI1
VDDD 23 digital supply voltage
FM-IFI2

40 41
33

MO/ST 24 mono/stereo and tuning indication output

AM-MIXER
PROGRAMMABLE
SHIFT REGISTER

MIXER
LAST-STATION
FM-IFO1

AM

XTAL 25 crystal input

DETECTOR
COUNTER
MEMORY

WINDOW
35

DGND 26 digital ground

BUS-CLOCK 27 bus-clock input
FM
IF1

OSCILLATOR

DATA 28 bus data input/output

AMOSC
FM-IFI1

AM

WRITE-ENABLE 29 bus write-enable input

6
37

P0 30 programmable output port (P0)

SWITCH
TUNER

MULTIPLEXER

OSCILLATOR
PRESCALER
STABILIZER

P1 31 programmable output port (P1)

CRYSTAL

AFC 32 450 kHz LC-input circuit for AM AFC

FRONT
END
AM

FM-IFI2 33 FMIF input 2 (input impedance typical 330 Ÿ)

VSTAB(B) 34 internal stabilized supply voltage (B)
25

26
38
34
39

23

2
7

FM-IFO1 35 FMIF output 1 (input impedance typical 330 Ÿ)

CGND

DGND

AM-IFI/O2 36 input/output to IFT; output: current source

FM-IFI1 37 FMIF input 1 (input impedance typical 330 Ÿ)
VDDD

XTAL
FM-ON/OFF

RIPPLE

AM-RFI
VCC1
VSTAB(A)
VSTAB(B)

COUNTI

VSTAB(A) 38 internal stabilized supply voltage (A)

FM-ON/OFF 39 FM ON/OFF port
AM-MIXER 40 open-collector output to IFT
 6-6 6-6

LAYOUT DIAGRAM - MAIN BOARD (5757) for /37/98

TOP SIDE
 6-7 6-7

LAYOUT DIAGRAM - MAIN BOARD (5757) for /37/98

BOTTOM SIDE
 6-8 6-8

CIRCUIT DIAGRAM - MAIN BOARD (5757) for /37/98

 6-9 6-9

LAYOUT DIAGRAM - MAIN BOARD (5762) for /05/12

TOP SIDE
 6-10 6-10

LAYOUT DIAGRAM - MAIN BOARD (5762) for /05/12

BOTTOM SIDE
 6-11 6-11

CIRCUIT DIAGRAM - MAIN BOARD (5762) for /05/12

 6-12 6-12

LAYOUT DIAGRAM - HP JACK BOARD LAYOUT DIAGRAM - HP JACK BOARD

TOP SIDE BOTTOM SIDE

CIRCUIT DIAGRAM - HP JACK BOARD

 6-13 6-13

Q631 9940 000 02642 TRANSISTOR, 3CA8550

Q803 9940 000 04218 TRANS PHP20N06T
4236 RF401 9940 000 04237 FM MODULE FE450-G11.
4236 T401 9940 000 04518 AM IFT 7MM C712KC-004
T402 9940 000 04518 AM IFT 7MM C712KC-004

T403 9940 000 01213 AM IFT 7MM

4233 T404 9940 000 04519 FM IFT 7MM KS2599
T405 9940 000 04517 AM OSC 7MM 7M1A2146
UR11 9940 000 04239 IC SAA6588T
UR12 9940 000 04241 IC 78L05 REGULATOR

VC403 9940 000 01615 TRIMMER CAP 10PF N450

VR401 9940 000 04232 VAR RES 100K 3P 1/10W
X401 9940 000 04231 CRYSTAL 75KHZ DT381
XR11 9940 000 04238 CRYSTAL 4.332MHZ

Note: Only these parts mentioned in the list are

normal service parts.

/05/12

4236
 7-1 7-1

CD & MCU BOARD

This board isn’t intend to repair. Only for orientation.

TABLE OF CONTENTS

Main Board Layout Top View ........................................... 7-2

Main Board Layout Bottom View ..................................... 7-3
Circuit Diagram - CD Part ................................................ 7-4
Circuit Diagram - MCU Part ............................................. 7-5
Layout Diagram - SW Board ........................................... 7-6
Electrical Parts List .......................................................... 7-6
 7-2 7-2

LAYOUT DIAGRAM - CD&MCU BOARD

TOP VIEW
 7-3 7-3

LAYOUT DIAGRAM - CD&MCU BOARD

BOTTOM VIEW
 7-4 7-4

CIRCUIT DIAGRAM - CD&MCU BOARD

CD PORTION
 7-5 7-5

CIRCUIT DIAGRAM - CD&MCU BOARD

MCU PORTION
 7-6 7-6

LAYOUT DIAGRAM - SW BOARD ELECTRICAL PARTS LIST - CD & MCU BOARD ( FOR CDM _ DAYANG M93 )
TOP SIDE
D128 994000004422 SCHOTTKY, PMEG2010
D165 994000004422 SCHOTTKY, PMEG2010
D302 996510000271 DIODE RLS4148 LL-34
D303 994000004285 ZENER DIODE UDZS6.8B UMD2
D304 994000004285 ZENER DIODE UDZS6.8B UMD2

D305 994000004285 ZENER DIODE UDZS6.8B UMD2

IC100 996500041888 IC MN6627954MA DSP
IC102 994000004278 IC SCA105 MOTOR DRIVER
IC103 996500041890 IC MN101E01J TA MASKING
IC104 994000005674 IC BR24L02F-WE2

IC300 994000004287 IC OTI-6888G USB DECODER

IC301 994000004286 IC AP34063A CONVERTER
IC302 994000004288 IC W27C512-45Z EPROM
IC501 996510006486 IC MN101CF91D MCU TQFP048
IC504 994000005674 IC BR24L02F-WE2

L100A 994000004279 RADIAL IND. 1.2R 2.2UH +/-5%

L155A 994000004279 RADIAL IND. 1.2R 2.2UH +/-5%
L156A 994000004279 RADIAL IND. 1.2R 2.2UH +/-5%
L157A 994000004279 RADIAL IND. 1.2R 2.2UH +/-5%
L158 996510006487 IND.MULTILAYER 2.2UH,210MA,10%

L159A 994000004226 RAD AXIAL IND. 100UH 3.5R

L302 994000004289 TOROIDAL COIL 220UH +/-10%
L303 994000004226 RAD AXIAL IND. 100UH 3.5R
LAYOUT DIAGRAM - SW BOARD L304A 996510006488 INDUCTOR 10UH+/-10% 0.1R
BOTTOM SIDE Q100 994000004275 TRANSISTOR 2SB709A

Q103 994000004223 TRANSISTOR 3CA8550 HFE=120-220

Q106 994000004224 TRANSISTOR 3DA8050 HFE=120-200
Q107 994000004223 TRANSISTOR 3CA8550 HFE=120-220
Q502 994000004267 TRANSISTOR MPS8050S
SW501 994000004283 DETECT SWITCH DTS-18 1P1T

SW502 994000004283 DETECT SWITCH DTS-18 1P1T

SW506 994000004259 SWITCH TACT TSA-06430-150
X100 994000004273 CER RESONATOR 16.93MHZ +/-0.5%
X101 996510000295 XTAL 8.38MHZ +/-20PPM CAP=20PF
X501 994000005671 XTAL 32.768KHZ +/-20PPM 12PF

X502 994000004266 X'TAL 4.194304MHZ 30PF

Note: Only these parts mentioned in the list are

normal service parts.
 8-1 8-1

IC BLOCK DIAGRAM - LCD DRIVER

HT1622

Block Diagram

AC POWER & DISPLAY & KEY

BOARD

PIN DESCRIPTION - LCD DRIVER

HT1622

Pad Description
P a d N o. P ad N am e I /O D escr i p t i on
TABLE OF CONTENTS
Chip selection input with Pull-high resistor. When the CS is logic
high, the data and command read from or written to the HT1622
Internal IC Diagram ......................................................... 8-1 are disabled. The serial interface circuit is also reset. But if CS is
1 CS I
Layout Diagram - AC Power Board ................................. 8-2 at logic low level and is input to the CS pad, the data and com -
Circuit Diagram - AC Power Board .................................. 8-3 mand transmission between the host controller and the HT1622
are all enabled.
Layout Diagram - AC Socket Board ................................ 8-4
Layout Diagram - Door Moter Board ............................... 8-4 READ clock input with Pull-high resistor. Data in the RAM of
the HT1622 are clocked out on the rising edge of the RD signal.
Layout Diagram - RC Board ............................................ 8-4 2 RD I
The clocked out data will appear on the data line. The host con -
Display Board .................................................................. 8-5 troller can use the next falling edge to latch the clocked out data.
Key Board ........................................................................ 8-6 WRITE clock input with Pull-high resistor. Data on the DATA
Speaker & Ant Board ....................................................... 8-7 3 WR I line are latched into the HT1622 on the rising edge of the WR sig-
Electrical Parts List .......................................................... 8-8 nal.
4 DATA I/O Serial data input/output with Pull-high resistor
5 VSS Negative power supply, ground
If the system clock comes from an external clock source, the ex -
6 OSCI I
ternal clock source should be connected to the OSCI pad.
7 VDD Positive power supply
8 VLCD I LCD operating voltage input pad
Time base or Watchdog Timer overflow flag, NMOS open drain
9 IRQ O
output
10, 11 BZ, BZ O 2kHz or 4kHz tone frequency output pair
12~14 T1~T3 I Not connected
15~22 COM0~COM7 O LCD common outputs
23~54 SEG0~SEG31 O LCD segment outputs
 8-2 8-2

LAYOUT DIAGRAM - AC POWER BOARD LAYOUT DIAGRAM - AC POWER BOARD

TOP SIDE BOTTOM SIDE
 8-3 8-3

CIRCUIT DIAGRAM - AC POWER BOARD

 8-4 8-4

LAYOUT DIAGRAM - AC SOCKET BOARD LAYOUT DIAGRAM - RC BOARD

TOP SIDE TOP SIDE

LAYOUT DIAGRAM - AC SOCKET BOARD LAYOUT DIAGRAM - RC BOARD

BOTTOM SIDE BOTTOM SIDE

LAYOUT DIAGRAM - DOOR MOTOR BOARD LAYOUT DIAGRAM - DOOR MOTOR BOARD
TOP SIDE BOTTOM SIDE
CIRCUIT DIAGRAM - RC BOARD
 8-5 8-5

LAYOUT DIAGRAM - DISPLAY BOARD CIRCUIT DIAGRAM - DISPLAY BOARD

TOP SIDE

LAYOUT DIAGRAM - DISPLAY BOARD

BOTTOM SIDE
 8-6 8-6

LAYOUT DIAGRAM - KEY BOARD CIRCUIT DIAGRAM - KEY BOARD

TOP SIDE

LAYOUT DIAGRAM - KEY BOARD

BOTTOM SIDE
 8-7 8-7

LAYOUT DIAGRAM - SP & ANT BOARD CIRCUIT DIAGRAM - SP & ANT BOARD
TOP SIDE

LAYOUT DIAGRAM - SP & ANT BOARD

BOTTOM SIDE
 9-1 9-1

SET MECHANICAL EXPLODED VIEW

^
% & *
$
#

!
9
8
7
6
5
34
2

40
(
)

¡
™
‡£

§
•
ºª
31
?
›
·

‹
36
35
 9-2

MECHANICAL & ACCESSORIES PARTS LIST

1 996510010723 LENS-CD DOOR /05/12 T901 ! 994000004431 POWER TRASFO AC115/230V /98
1 996510012871 LENS-CD DOOR /98 T902 ! 994000004245 POWER TRASFO EI-28 AC230V /05/12
2 996510010722 DOOR-CD RF401 994000004237 FM FRONT END MODULE /05/12
3 996510010724 HOLDER CD DOOR CARRIER (L)
4 994000004302 COVER POWER BUTTON

5 996510010728 KNOB-VOLUME
6 996510010726 LENS DISPLAY
7 996510010725 HOLDER CD DOOR CARRIER (R)
8 996510010729 LENS BAR
9 996510010721 CABINET FRONT

11 996510010727 BUTTON POWER/SOURCE Note: Only these parts mentioned in the list are
15 994000004325 BELT MOTOR normal service parts.
17 996510010720 CABINET REAR FOR /12/05
17 996510012870 CABINET REAR /98
19-21 996520032987 STAND PORTION OF MCM277

22 9940 000 04323 CD DAMPER (BLACK) 20DEG

23 996510010437 CD MECHANISM M93BGP-BF
24 9940 000 01664 DAMPER GEAR ASSEMBLY
26 9940 000 03384 SPRING TORSION LEFT
28 994000004304 BRACKET OPEN/CLOSE BUTTON

29 994000004324 SPRING CONTROL PANEL

30 996510010730 BUTTON OPEN/CLOSE
31 994000004315 COVER PLAY BUTTON
32 994000004309 BUTTON FW/FF
33 996510010732 PANEL FUNCTION /12/05
33 996510012873 PANEL FUNCTION /98
34 996510010733 COVER FUNCTION PANEL 05/12/98
35 996510010731 BUTTON FUNCTION
36 994000004308 BUTTON PLAY
37 994000004333 IR LENS
38 994000004316 PULLEY SERVO MOTOR

39 994000004314 BRACKET FUNCTION PANEL

40 996510006485 CD/MCU BOARD ASS'Y (M93) /05/12
SPK 996510010734 SPEAKER BOX /05/12

FMA 994000004329 FM ANT WIRE 75R 1.0M

REM 996510028568 REMOTE CONTROL /05/12

REM 996510028568 REMOTE CONTROL /98
AML 994000004331 AM LOOP ANT 164X75MM
ACW ! 994000002223 POWER AC WIRE BSI /05
ACW ! 994000001675 POWER AC WIRE VDE 230V /12

ACW ! 994000002082 POWER AC CORD VDE 2C 1.5M /98

FFC1 994000004281 FFC 21P P1.25MM L110MM C TYPE
FF1 996510006481 FFC 7P P1.25MM L155MM D TYPE
T901 ! 994000004244 POWER TRASFO AC230V H50 /05/12
 8-8 8-8

& DISPLAY & KEY & SP & ANT

& RC & AC SOCKET & DOOR MOTOR BOARD

VR701 9940 000 04258 ROTARY ENCODER

9940 000 04251 EC TERMINAL 1P
F901 ! 9940 000 04243 FUSE PTU 1A 250V 3.9X10.5MM /37/98
RL901 ! 9940 000 04246 RELAY DC6V AC10A /05/12/37
T901 ! 9940 000 04244 POWER TRASFO AC230V /05/12

T902 ! 9940 000 04245 POWER TRASFO AC230V /05/12

65 1 10715 1-060-010
T901 ! 9940 000 04431 POWER TRASFO AC115/230V /98
03605 MICRO PHONE JACK CKX-3.5-23

Note: Only these parts mentioned in the list are

normal service parts.

65 100 01366 IR SENSOR FM-6038TM2-5AN

 9-3

ELECTRICAL PARTS LIST

CF401 994000004236 FM CERAMIC FILTER 10M7 IC402 994000004234 VAR. CAP DIODE HN-1V02H
CF402 994000004236 FM CERAMIC FILTER 10M7 IC501 996510006486 IC MN101CF91D MCU TQFP048
D100 996510010718 DIODE BZX79-C4V3 IC504 994000005674 IC BR24L02F-WE2
D128 994000004422 SCHOTTKY, PMEG2010 EA IC601 996500041701 IC TDA7468D SOUND SO28
D165 994000004422 SCHOTTKY, PMEG2010 EA IC610 994000004225 IC LM317P VOL REGULATOR

D300 996510006964 DIODE 1N5819 DO-41 IC701 994000004256 IC HT1622 LCD DRIVER
D302 996510000271 DIODE RLS4148 LL-34 IC801 994000004219 IC TDA1517 POWER AMPLIFIER
D303 994000004285 ZENER DIODE UDZS6.8B UMD2 IC901 996500040080 IC AP1117E33LA REGULATOR
D304 994000004285 ZENER DIODE UDZS6.8B UMD2 JK701 996510010715 USB JACK 4P
D305 994000004285 ZENER DIODE UDZS6.8B UMD2 JK702 994000003605 MICRO PHONE JACK

D401 996510007742 DIODE, HIGH BAS316 JK801 994000003318 HP JACK D3.6MM

D501 996510010716 DIODE,BZX79-C3V9 JK802 994000004248 SPK TERMINAL PST-403B-01
D502 996510010717 DIODE, BZX79-C4V7 TAPING L100A 994000004279 RADIAL IND. 1.2R 2.2UH +/-5%
D618 996510000271 DIODE RLS4148 LL-34 L155A 994000004279 RADIAL IND. 1.2R 2.2UH +/-5%
D750 996510000271 DIODE RLS4148 LL-34 L156A 994000004279 RADIAL IND. 1.2R 2.2UH +/-5%

D801 996510000271 DIODE RLS4148 LL-34 L157A 994000004279 RADIAL IND. 1.2R 2.2UH +/-5%
D802 996510000271 DIODE RLS4148 LL-34 L159A 994000004226 RAD AXIAL IND. 100UH 3.5R
D803 996510000271 DIODE RLS4148 LL-34 L302 994000004289 TOROIDAL COIL 220UH +/-10%
D804 996510000271 DIODE RLS4148 LL-34 L303 994000004226 RAD AXIAL IND. 100UH 3.5R
D807 996510000271 DIODE RLS4148 LL-34 L304A 996510006488 INDUCTOR 10UH+/-10% 0.1R

D880 996510000271 DIODE RLS4148 LL-34 L403 996510010713 AM ANT 7MM 7M1A2204N
D881 994000004422 SCHOTTKY, PMEG2010 EA L605 994000004227 28UH CORE: 6T 715R 1.2A
D905 996510000271 DIODE RLS4148 LL-34 L620 994000004226 RAD AXIAL IND. 100UH 3.5R
D991 996510000271 DIODE RLS4148 LL-34 L702 994000004279 RADIAL IND. 1.2R 2.2UH +/-5%
D992 996510000271 DIODE RLS4148 LL-34 L810 994000004247 RADIAL AXIAL IND. 8.0UH 60MR

DZ401 996510010712 CH-DIODE, BZX284-C11 L811 994000004247 RADIAL AXIAL IND. 8.0UH 60MR
DZ801 996510007763 ZENER DIODE BZX55C15V L812 994000004247 RADIAL AXIAL IND. 8.0UH 60MR
DZ802 996500041721 ZENER DIODE BZX79-C10 L813 994000004247 RADIAL AXIAL IND. 8.0UH 60MR
DZ803 996510010711 ZENER DIODE BZX79-C5V6 L901 994000002657 AC LINE FILTER 3MH 1A
F601 ! 994000004229 FUSE PTU 2A 250V LCD701 996510006483 LCD DISPLAY 1/8 DUTY 1/4 STN

F602 ! 994000004228 FUSE S506 T1.6AL 250V LED701 996510006484 LED 4MM WHITE
F901 ! 994000004243 FUSE PTU 1A 250V 3.9X10.5MM LED702 996510000292 LED 3MM 3R4HD-7(RED)
FF1 996510006481 FFC 7P P1.25MM L155MM M100 994000004253 DC MOTOR JQ32-55K415 DC3V
FMANT 994000004249 RCA JACK RCA-125 Q100 994000004275 TRANSISTOR 2SB709A
IC100 996500041888 IC MN6627954MA DSP Q101 996510006954 CH-TRANSISTOR,BC817-25

IC102 994000004278 IC SCA105 MOTOR DRIVER Q102 996510006954 CH-TRANSISTOR,BC817-25

IC103 996500041890 IC MN101E01J TA MASKING Q103 994000004223 TRANSISTOR 3CA8550
IC104 994000005674 IC BR24L02F-WE2 Q104 996510006954 CH-TRANSISTOR,BC817-25
IC300 994000004287 IC OTI-6888G USB DECODER Q105 996510006954 CH-TRANSISTOR,BC817-25
IC301 994000004286 IC AP34063A CONVERTER Q106 994000004224 TRANSISTOR 3DA8050

IC302 996510010719 IC AT27C512R OTP EPROM Q107 994000004223 TRANSISTOR 3CA8550

IC302 994000004288 IC W27C512-45Z EPROM Q301 996510000939 TRANSISTOR BC807-25 PNP
IC401 994000004235 IC TEA5762H/V1 Q302 996510006954 CH-TRANSISTOR,BC817-25
 9-4

ELECTRICAL PARTS LIST

Q303 996510000939 TRANSISTOR BC807-25 PNP X300 994000004284 XTAL 14.318MHZ +/-20PPM 20PF
Q501 996510006954 CH-TRANSISTOR,BC817-25 X401 994000004231 X'TAL 75KHZ +/-20PPM DT381
Q502 994000004267 TRANSISTOR MPS8050S X501 994000005671 XTAL 32.768KHZ +/-20PPM 12PF
Q503 996510006954 CH-TRANSISTOR,BC817-25 X502 994000004266 X'TAL 4.194304MHZ 30PF
Q504 996510006954 CH-TRANSISTOR,BC817-25 XR11 994000004238 X'TAL 4.332MHZ +/-20PPM

Q601 994000004224 TRANSISTOR 3DA8050 HFE=120-200

Q610 994000004223 TRANSISTOR 3CA8550 HFE=120-220
Q631 994000004223 TRANSISTOR 3CA8550 HFE=120-220
Q701 994000004224 TRANSISTOR 3DA8050 HFE=120-200
Q702 994000004224 TRANSISTOR 3DA8050 HFE=120-200

Q803 994000004218 N-CHANNEL MOS TRANS PHP20N06T

Q905 994000004224 TRANSISTOR 3DA8050 HFE=120-200
RF401 994000004237 FM FRONT END MODULE FE450-G11
RI501 996510001366 IR SENSOR (OPTO)
RL901 ! 994000004246 RELAY ME-7-006-HSL DC6V AC10A

SW501 994000004283 DETECT SWITCH DTS-18 1P1T

SW502 994000004283 DETECT SWITCH DTS-18 1P1T
SW506 994000004259 SWITCH TACT TSA-06430-150
SW701 994000004259 SWITCH TACT TSA-06430-150
SW702 994000004259 SWITCH TACT TSA-06430-150

SW703 994000004259 SWITCH TACT TSA-06430-150

SW704 994000004259 SWITCH TACT TSA-06430-150
SW705 994000004259 SWITCH TACT TSA-06430-150
SW708 994000004259 SWITCH TACT TSA-06430-150
SW709 994000004259 SWITCH TACT TSA-06430-150

SW710 994000004259 SWITCH TACT TSA-06430-150 Note: Only these parts mentioned in the list are
SW715 994000004259 SWITCH TACT TSA-06430-150 normal service parts.
SW716 994000004259 SWITCH TACT TSA-06430-150
SW717 994000004259 SWITCH TACT TSA-06430-150
T401 994000004518 AM IFT YELLOW 7MM C712KC-004

T402 994000004518 AM IFT YELLOW 7MM C712KC-004

T403 996510010714 AM IFT BLACK 7MM 7M4A2011N
T404 994000004519 FM IFT BLACK 7MM KS2599
T405 994000004517 AM OSC BROWN 7MM 7M1A2146
T901 ! 994000004244 POWER TRASFO AC230V H50.

T902 ! 994000004245 POWER TRASFO EI-28 AC230V

UR11 994000004239 IC SAA6588T RADIO RECEIVERS
UR12 996510001350 IC LM78L05 3-TERMINAL TO-92
VC403 994000001615 TRIMMER CAP 10PF N450
VR401 994000004232 VARI RES 100K 3P 1/10W+/-30%

VR701 994000004258 ROTARY ENCODER

X100 994000004273 CER RESONATOR 16.93MHZ +/-0.5%
X101 996510000295 XTAL 8.38MHZ +/-20PPM CAP=20PF
 10-1
10-1

SOFTWARE VERSION CHECKING

How to check Software Version on set Front Panel

Check software version:
(1)Plug in the set;
(2)Hold "PROGRAM" and "DBB" buttons together when set on "ECO Power" mode (LED light is on);
(3)The LCD will display the software version as " Mxxx xxx"

To clear all program station of tuner mode:

(1)Plug in the set;
(2)Hold "STOP" button when set on "ECO Power" mode (LED light is on);
(3)The LCD will display full screen,all program station of tuner will be cleared.

Starting Serial Number:

EF2A0913000001
 11 - 1 11 - 1

SET BLOCK DIAGRAM

 11 - 2 11 - 2

SET WIRING DIAGRAM

 12-1 12-1

PCB LAYOUT - MAIN BOARD (TOP VIEW)

 12-2 12-2

PCB LAYOUT - MAIN BOARD (BOTTOM VIEW)

 12-3 12-3

CIRCUIT DIAGRAM - MAIN BOARD

 13-1 13-1

PCB LAYOUT - CD & CD DOOR MOTOR & LIMIT SWITCH BOARD

(TOP VIEW)
 13-2 13-2

PCB LAYOUT - CD & CD DOOR MOTOR & LIMIT SWITCH BOARD

(BOTTOM VIEW) - ONLY FOR REFERENCE
 13-3 13-3

CIRCUIT DIAGRAM - CD & LIMIT SW BOARD

ONLY FOR REFERENCE
 14-1 14-1

PCB LAYOUT - AC POWER & HP JACK & SP & ANT JACK & RC BOARD
(TOP VIEW)
 14-2 14-2

PCB LAYOUT - AC POWER & HP JACK & SP & ANT JACK & RC BOARD
(BOTTOM VIEW)
 14-3 14-3

PCB LAYOUT - KEY BOARD

(TOP VIEW)

PCB LAYOUT - KEY BOARD

(BOTTOM VIEW)
 14-4 14-4

CIRCUIT DIAGRAM - KEY BOARD & AC POWER BOARD

 14-5 14-5

CIRCUIT DIAGRAM - HP JACK & SP & ANT & RC BOARD

 15-1 15-1

SET MECHANICAL EXPLODED VIEW

9
 15 - 2 15 - 2
(FOR ALI SOLUTION)
MECHANICAL & ACCESSORIES PARTS LIST ELECTRICAL PARTS LIST ELECTRICAL PARTS LIST

Loc. 12NC Description Loc. 12NC Description Loc. 12NC Description

MAIN UNIT DISPLAY/MCU PCB ASS'Y CD/USB PCB ASSY (ONLY FOR REFERENCE)

1 996510010723 LENS-CD DOOR FOR /12/05/37 D3 996510026339 DIODE MMBD4148W MQ1 996500041698 CH-TRANS. 8050M SOT23
D3 996510026385 DIODE LS4148-GS08 MQ11 996510007048 CH-TR. PNP SS8550LT1 SOT-23
3 996510010722 DOOR-CD D7 996510026339 DIODE MMBD4148W MQ12 996510007048 CH-TR PNP SS8550LT1 SOT-23
CH-TR.
4 996510010733 COVER FUNCTION PANEL D7 996510026385 DIODE LS4148-GS08 MQ13 996500041698 CH-TRANS. 8050M SOT23
7 994000004308 BUTTON PLAY IC1 996510026362 MCU CA6810F LQFP64 MQ14 996500041698 CH-TRANS. 8050M SOT23
8 9965 00 073
996510010731 UTTON FUNCTION
BUTTON LCD1 996510006483 LCD DISPLAY 1/8 DUTY 1/4 STN MQ2 996510007048 CH-TR.
CH SOT-23
TR. PNP SS8550LT1 SOT 23
9 996510026403 PANEL FUNCTION /12/05/37 LED701 996510036396 LED 4MM WHITE MQ3 996500041698 CH-TRANS. 8050M SOT23
LED701 996510026368 LED 4MM WHITE MQ4 996500041698 CH-TRANS. 8050M SOT23
10 994000004309 BUTTON FW/FF LED702 996510000292 LED 3MM 3R4HD-7(RED) TAPING MQ5 996500041698 CH-TRANS. 8050M SOT23
11 994000004315 COVER PLAY BUTTON Q1 996500041698 CH-TRANS. 8050M SOT23 MQ6 996500040080 IC AP1117E33LA REGULATOR
12 996510010725 HOLDER CD DOOR CARRIER (R) Q10 996510007049 CH-TR. PNP 3CA8550M SOT-23 MQ6 996500041892 IC AZ1117H-3.3 REGULATOR
13 996510010724 HOLDER CD DOOR CARRIER (L) Q2 996500041698 CH-TRANS. 8050M SOT23 MQ7 996510000285 TRANSISTOR 2SB1132R
15 996510010728 KNOB VOLUME
KNOB-VOLUME Q4 996510006954 CH TRANSISTOR BC817
CH-TRANSISTOR BC817-25
25 MS506 996510026354 KFC-A06-43
SWITCH TACT KFC A06 43
16 996510026382 MECHANICAL SECTION (ALI) Q5 996510007049 CH-TR. PNP 3CA8550M SOT-23 MU1 996510026364 MCU ALI-M5673 QFP/128P
16 994000004302 COVER POWER BUTTON Q6 996500041698 CH-TRANS. 8050M SOT23 MU3 996510026376 IC 2M FLASH EN25F20-100GCP
17 996510010726 LENS DISPLAY /12/05/37 SW705 996510026354 SWITCH TACT KFC
KFC-A06-43
A06 43 MU3 996510026378 IC 2M FLASH EN25P20-100GCP
EN25P20 100GCP
SW708 996510026354 SWITCH TACT KFC-A06-43 MU4 996510026353 IC SA1469XH 4CH MOTOR DRIVER
19 996510010730 BUTTON OPEN/CLOSE U1 996510026375 IC AZ393M-E1 MU4 996510026398 IC MM1469XH 4CH MOTO DRIVER
20 996510010729 LENS BAR U2 996510026333 IC FM24C02-SO-T MY1 996510026365 CER RESONTOR 1693MHZ +/-05
23 996510010721 CABINET FRONT FOR /12 U2 996510026349 IC BR24C02SOP8 MZD3 996510026358 ZENER DIODE BZX384-C5V6
25 996510010727 BUTTON POWER/SOURCE VR701 994000004258 ROTARY ENCODER MZD4 996510026358 ZENER DIODE BZX384-C5V6
29 994000004304 BRACKET OPEN/CLOSE BUTTON Y1 996510026359 XTAL 32768KHZ +/-30PPM U1 996510026337 IC RT9702PB POWER SWITCHES-5
34 996510026351 CD MECHANISM DM86
DM86-1 1 ZD1 996510026348 ZENER DIODE BZX384 C3V3
BZX384-C3V3 U2 996510007057 IC AZ1117H
AZ1117H-ADJTRE1REGULATORSOT
ADJTRE1REGULATORSOT
61 996510010720 CABINET REAR FOR /12 ZD5 996510026395 ZENER DIODE BZX384-C5V1
62-63-69 996510027355 STAND PORTION OF MCM277 ZD6 996510026395 ZENER DIODE BZX384-C5V1

FMANT 996510000308 FM ANT WIRE 75R L1.0M MAIN PCB ASSY

REM 996510028568 REMOTE CONTROL
SPKBOX 996510019466 SPK BOX FOR MCM277/12 IN PAIR CD/USB PCB ASSY ((ONLY FOR REFERENCE)) AUDIO PROCESSOR PORTION
AMANT 996510026334 AM ANT ASSEMBLY OF MCM277 AD02 996510026339 DIODE MMBD4148W
43 996510026377 DISPLAY/MCU BOARD ASSEMBLY MS501 996510026394 DETECT SWITCH DTS-18-PA46 1P1T AD02 996510026385 DIODE LS4148-GS08
36 996510026373 CD SERVO PWB ASSEMBLY MS502 996510026394 DETECT SWITCH DTS-18-PA46 1P1T AD03 996510026339 DIODE MMBD4148W
42 996510026336 MAIN PWB ASSEMBLY MD1 996510026339 DIODE MMBD4148W AD03 996510026385 DIODE LS4148
LS4148-GS08
GS08
58 996510026343 AC POWER ASSEMBLY MD1 996510026385 DIODE LS4148-GS08 AJ2 994000004215 FILTER BEAD RH3.5X6X0.8
ACCORD ! 996510026381 AC POWER CORD HL-77 L1800MM MD2 996510026339 DIODE MMBD4148W AL02 994000004227 28UH CORE:T9X5X3 6T 715R 1.2A
MD2 996510026385 DIODE LS4148-GS08 AQ01 996510006954 CH-TRANSISTOR
MD4 996510026339 DIODE MMBD4148W AQ02 996510026397 TRANSISTOR 2SB772-P PNP
MD4 996510026385 DIODE LS4148-GS08 AQ03 996500041698 CH-TRANS. 8050M SOT23
MD5 996510026339 DIODE MMBD4148W AU03 996510001347 IC ET2314 SOUND SO28
MD5 996510026385 DIODE LS4148-GS08 F602 ! 994000004228 FUSE S506 T1.6AL 250V
 15 - 3 15 - 3
(FOR ALI SOLUTION)
ELECTRICAL PARTS LIST ELECTRICAL PARTS LIST ELECTRICAL PARTS LIST

Loc. 12NC Description Loc. 12NC Description Loc. 12NC Description

MAIN PCB ASSY KEY PCB ASSY AC POWER ASSY

F602 ! 996510026357 FUSE 50T T16AL 250V D1 996510026338 MULT VAR SDV1608H180C050 T901 ! 996510026372 TRASFO UI39 AC230V T08829A
F602 ! 996510026369 FUSE 5K 16A 250V D2 996510000271 DIODE RLS4148 LL‐34
LL 34 T902 ! 996510026391 TRASFO EIEI‐28
28 230V T08628B
FB1 994000004215 FILTER BEAD RH3.5X6X0.8 D2 996510026339 DIODE MMBD4148W SP&ANT JACK PORTION
IC610 994000004225 IC LM317P VOL REGULATOR D2 996510026385 DIODE LS4148‐GS08 D991 996510016501 DIODE IN4148FT‐72
Q1 994000004224 TRANSISTOR 3DA8050 HFE=120‐200 D3 996510026338 MULT VAR SDV1608H180C050 D992 996510016501 DIODE IN4148FT‐72
ZD1 996510007003 ZENER DIODE 6.2V 1/2W TAPING D4 996510000271 DIODE RLS4148 LL‐34 D994 996510016501 DIODE IN4148FT‐72
ZD2 996510007762 ZENER DIODE 9V1 1/2W TAPING. D4 996510026339 DIODE MMBD4148W D995 996510016501 DIODE IN4148FT‐72
POWER AMPLIFIER PORTION D4 996510026385 DIODE LS4148‐GS08 FMANT 994000004249 RCA JACK RCA‐125
AC22 996510026338 MULT VAR SDV1608H180C050 D5 996510026338 MULT VAR SDV1608H180C050 JK802 994000004248 SPEAKER TERMINAL PST‐403B‐01
PST 403B 01
AD5 996510016501 DIODE IN4148FT‐72 D8 996510000271 DIODE RLS4148 LL‐34 L810 994000004247 RADIAL AXIAL IND. 8.0UH 60MR
D803 996510016501 DIODE IN4148FT‐72 D8 996510026339 DIODE MMBD4148W L811 994000004247 RADIAL AXIAL IND. 8.0UH 60MR
D806 996510016501 IN4148FT‐72
DIODE IN4148FT 72 D8 996510026385 LS4148‐GS08
DIODE LS4148 GS08 L812 994000004247 RADIAL AXIAL IND. 8.0UH 60MR
D807 996510016501 DIODE IN4148FT‐72 FB701 994000004215 FILTER BEAD RH3.5X6X0.8 L813 994000004247 RADIAL AXIAL IND. 8.0UH 60MR
D811 996510016501 DIODE IN4148FT‐72 JK701 996510010715 USB JACK 4P AC SOCKET PORTION
F601 ! 994000004229 FUSE PTU 2A 250V JK702 994000003605 MICRO PHONE JACK L901 996510026396 LINE FILTER 38mH 38mH 380MR
F601 ! 996510026387 FUSE 30TS 2A 250V SW701 996510026354 SWITCH TACT KFC‐A06‐43 RC PORTION
F601 ! 996510026389 FUSE 3N 2A 250V SW702 996510026354 SWITCH TACT KFC‐A06‐43 RI501 996510001366 IR SENSOR (OPTO)
FD05 996510016501 DIODE IN4148FT‐72 SW703 996510026354 SWITCH TACT KFC‐A06‐43
FD15 996510016501 DIODE IN4148FT‐72
IN4148FT 72 SW704 996510026354 SWITCH TACT KFC
KFC‐A06‐43
A06 43
FU1 996500041892 IC AZ1117H‐3.3 REGULATOR SW709 996510026354 SWITCH TACT KFC‐A06‐43
Q801 996510006954 CH‐TRANSISTOR SW710 996510026354 SWITCH TACT KFC‐A06‐43
Q804 996500041700 CH‐TRANS. DTC114YKA NPN SW715 996510026354 SWITCH TACT KFC‐A06‐43
Q805 996510000939 TRANSISTOR BC807‐25 PNP SW716 996510026354 SWITCH TACT KFC‐A06‐43
Q806 996510006954 CH‐TRANSISTOR SW717 996510026354 SWITCH TACT KFC‐A06‐43 Note: Only these parts mentioned in the list are
Q807 996510006954 CH‐TRANSISTOR normal service parts.
p
Q812 996510006954 CH‐TRANSISTOR
Q813 996510006954 CH‐TRANSISTOR
U801 996510001348 IC POWER AMPLIFIER TFA9842BJ. AC POWER ASSY
ZD804 996510007003 ZENER DIODE 66.2V
2V 1/2W TAPING
TUNER PORTION HP JACK PORTION
FERRITE 996510026347 FERRITE CORE RH16x28x9 HJK1 996510026367 HP JACK CK‐35‐39 7P D36MM
FFB1 994000004215 FILTER BEAD RH3
RH3.5X6X0.8
5X6X0 8 AC POWER PORTION
FJ7 994000004215 FILTER BEAD RH3.5X6X0.8 D905 996510016501 DIODE IN4148FT‐72
FQ02 996500041698 CH‐TRANS. 8050M SOT23 D906 994000004422 SCHOTTKY
FQ06
Q 996510006954 CH‐TRANSISTOR F901 ! 994000004243 FUSE PTU 1A 250V 3.9X10.5MM
FQ07 996510007049 CH‐TR. PNP 3CA8550M SOT‐23 F901 ! 996510026342 FUSE 3N 1A 250V
FU01 996510026346 TUNER MODULE F901 ! 996510026345 FUSE 30TS 1A 250V
LPF1 996510026355 FM BP FILTER LPF88A1 Q905 994000004224 TRANSISTOR 3DA8050 HFE=120‐200
T5 996510026352 AM ANT BLK YD‐482N 10mm RL901 ! 994000004246 RELAY ME‐7‐006‐HSL DC6V AC10A
ZD3 996510016482 ZENER DIODE BZX79‐B3V9 RL901 ! 996510026383 RELAY TV‐5 DC6V AC10A
 16-1

REVISION LIST

1.0 Manual 3141 785 32370

Initial Service Manual released.

1.1 Manual 3141 785 32371

In this version, version /05 added.
1) P9-1 Mechanical and Accessories Partslist updated.

1.2 Manual 3141 785 32372

In this version, version /98 added.
1) P9-2 Mechanical and Accessories Partslist updated.
2) P1-2 PCBs Service Policy Variations added.

1.3 Manual 3141 785 32373

In this version,
1) P9-2 Mechanical and Accessories Partslist updated.
40 996510006485 CD/MCU BOARD ASS'Y (M93) /05/12 (WAS 996520033047)

1.4 Manual 3141 785 32374

In this version, Page 9-1 & Page 9-2 have been updated.
1) In Page 9-1: Item No. 33 & Item No.34 exchanged.
(the original sequence numbers -No.33 & No. 34 mixed up)
2) In Page 9-2: Pos. No. 33 ---->new 12nc for /98 added.
33 996510012873 PANEL FUNCTION /98

1.5 Manual 3141 785 32375

In this version, Ali solution is introduced and Chapter 10 to Chapter 15 have
been added.

1.6 Manual 3141 785 32376

In this version, Page 15-2 updated.

LED701 996510036396 LED 4MM WHITE (WAS 996510006484)