Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                

A Different Approach To Estimate Air Moisture

Download as docx, pdf, or txt
Download as docx, pdf, or txt
You are on page 1of 7

A different approach to estimate air moisture

Un enfoque diferente para estimar la humedad del aire

Víctor Almanza Veloz1

José Agustín García Reynoso1

1
Instituto de Ciencias de la Atmósfera y Cambio Climático.

ABSTRACT

When comparing dry and humid air densities and trying to understand which one is
denser, the right answer not necessarily follows our intuition. This happens in the
Environmental Engineering lectures when students are asked: Is dry or humid air
denser? To understand the role of water vapor in air, a method to compute the mass
mixing ratio, specific humidity and average molecular weight is presented. This set of
equations is more precise than the traditional method and clarifies how water vapor
influences physical properties such as air density and bulk molecular weight.

Keywords: Avogadro; mixing ratio; molecular weight; specific humidity

RESUMEN

Al comparar las densidades del aire seco y húmedo y tratar de entender cuál es más
densa, la respuesta correcta no necesariamente sigue nuestra intuición. Esto sucede en
las clases de Ingeniería Ambiental cuando se pregunta a los estudiantes: ¿Es más denso
el aire seco o el húmedo? Para comprender el papel del vapor de agua en el aire, se
presenta un método para calcular la proporción de mezcla en masa, la humedad
específica y el peso molecular promedio. Este conjunto de ecuaciones es más preciso
que el método tradicional y aclara cómo el vapor de agua influye en propiedades físicas
como la densidad del aire y el peso molecular aparente.

Palabras clave: Avogadro; proporción de mezcla; peso molecular; humedad específica

INTRODUCTION

In teaching sessions when the following question is raised: “Which air mass is
heavier: a dry one or one containing water vapor?”, more than half of the class,
give the wrong answer and around 20% guess the right answer. Perhaps based on
their own experience, they assumed that a moistened material increases its weight.

In textbooks and manuals, estimating both relative and absolute humidity uses the
molecular water-air ratio (ε=0.622); however, obtaining the correct answer using
those equations may not be straight forward. In this work, the laws of Avogadro’s,
Dalton’s and Amagat’s are used with the aim to simplify the computation of
humidity; provide an approach to help to identify the influence of water content in
the density and to increase its precision.

The set of equations presented here were compared with the known ones and can
be used in teaching this subject to both professionals and the public.

Objectives

To provide a new perspective to students that might assist to infer the effect of
humidity in estimating the moist air density; and to present a set of equivalent
equations that can be employed in teaching this topic.

Method

In a gas mixture, the physical properties of each constituent contribute to the bulk
composition. For instance, according to Dalton’s law, the partial pressure of each
compound contributes to the total pressure of the mixture. Based on that, the dry
average molecular weight (Md) of a gas mixture of n compounds can be obtained
from:

Md=Σni=1Miyi��=Σ�=1����� (1)

Where M i and y i are the molecular weight and the mol fraction of the
constituent i respectively. Moreover, the mole fraction can be obtained from the
ratio of the compound with respect to the mixture:

yi=PiPt=ViVt=nint��=����=����=���� (2)

Where: Pi, Vi and ni are the pressure, volume and moles of compound i,
respectively; and Pt, Vt and nt are the total pressure, volume and moles of the gas
mixture. Thus, for the mixture we have ∑ y i = 1

As for the case of dry air, the mole fraction of oxygen (O 2), nitrogen (N2) and argon
(Ar) are yO2=0.209, yN2=0.780 and yAr=0.009 respectively (Wallace & Hobbs, 2006). Using
the molecular weight of each one, O2 = 32 g/mol, for N2 = 28 g /mol and for Ar =
40 g /mol, the dry air molecular weight can be obtained using equation 1:

Md=32(0.209)+28(0.78)+40(0.009)=28.9 g /
molMd=32(0.209)+28(0.78)+40(0.009)=28.9 � /���

It can be noticed that the molecular weight of dry air (M d) is between the molecular
weights of oxygen and argon. Since nitrogen is more abundant, the average
molecular weight Md is close to it rather than to the other air components.

From the principle of Avogadro, the wet fraction (f H) can be defined as the ratio of
water molecules and wet air molecules. In addition, we can also use the ratio of
water vapor volume and humid air volume, and the ratio of the partial pressure of
water vapor and the total pressure:

fH=nH20nH20+nair=VH20VH20+Vair=PH20PH20+Pair��=��20��20+����=��20��20+�
���=��20��20+���� (3)
Where f H is the wet fraction, nH2O, VH2O PH2O are the moles of water vapor, volume
and pressure respectively and nair, Vair, Pair - are the dry air moles number, volume
and pressure respectively. The values of f H ranges from 0 for dry air and 1 value
for pure water vapor.

Using a similar approach, the molecular weight of wet air (M a), which is a mixture
of water (Mw) and dry air (Md) molecular weights can be estimated as follows:

Ma=(1−fH)Md + fHMwMa=(1-��)M� + ��Mw (4)

Where Mw is the water molecular weight of water (18 g/gmol) and M d is the dry air
molecular weight of dry air (28.9 g / gmol).

We define an air parcel as an air volume that has a specific pressure, temperature
and fixed composition conditions. Using equation (4) it is possible to calculate and
plot the values of Ma for dry air (f H =0) and for water vapor (f H =1) Figure
1 presents the possible Ma values. It is observed that when water vapor content
increases, the air parcel molecular weight goes from the molecular weight of the
dry air (Md = 29 g/mol) to the molecular weight of the water (Mw = 18 g/mol).

Figure 1 Change in molecular weight with respect to the wet fraction (fH).

Nevertheless, as environmental conditions, the general equation of the gases is


satisfied and the gas density can be obtained with the following relation:

PV=mMRT��=��RT (5)

Where P-pressure (atm), V- volume (L), M - Mass of the compound (g) molecular
weight (g / mol), R gas constant (L atm K-1 mol-1) and T temperature (K).

Density (ρ) can be obtained from Equation 5:


ρ=mV=PMRT�=��=PM�� (6)

Where ρ is the gas density (g/L). From the equation 6 it can be observed that the
density of a gaseous mixture with the same pressure and temperature conditions is
directly proportional to the gas molecular weight. Therefore, in an air parcel that
contains water vapor, its density will be lower than that of dry air at the same
conditions of T and P. Hence, wet air is lighter than dry air.

Absolute humidity

Absolute humidity is the concentration of water vapor in the air. It refers to the
mass of water vapor in a unit of air volume (Stull, 2015), and corresponds to the partial
density:

ρv=mH20Volume��=��20������ (7)

Using equation 6 in 7 the following expression is obtained:

ρv=fHPMwRT��=������� (8)

From the above equation, you can identify the partial pressure of the water is P w =
fHP.

Specific humidity

The specific humidity (q) is the ratio of water vapor mass with respect to the total
mass of humid air (Jacobson, 1999):

q=ρwρα�=���� (9)

Substituting water (eq. 8) and wet air (using eq. 4 in eq. 6) densities in eq. 9 the
following relation is obtained:

q=fHMw(1−fH)Md+fHMw�=�HMw1-����+���� (10)

Equation 10 shows an explicit relation between dry and water molecular weights in
the specific humidity estimation.

Mass Mixing Ratio

The mass mixing ratio (r) is the water vapor mass (m) with respect to the dry air
mass (Stull, 2015):

r=massH20massd=ρH20ρd�=�����20�����=��20�� (11)

Substituting equation 6 for dry air and water vapor in equation 11, and simplifying,
is obtained:

r=fHMw(1−fH)Md�=����(1-��)�� (12)

Comparison between equations


The following equations are commonly used in text books ( Jacobson, 1999; Perry et al.,
1997 Stull, 2015
; ) for computing different quantities using the ratio water-air molecular
weight (ε=0.622) in the case of the mass mixing ratio the equation used is:

r=εPwPd�=����� (13)

Where Pw is water vapor partial pressure, Pd is the dry air partial pressure.

The specific humidity is calculated by:

q=r1+r�=�1+� (14)

And the moist air molecular weight:

Mα=Md1+1−εeq��=��1+1-��� (15)

Using the known equations can have an error with respect to the proposed
equations of up to 0.21%. For r and q, using ambient water content Pw=10 hPa,
Pd=1013 hPa this is mainly because ε has only 3 significant figures even though
equations 10 and 14 are equivalent algebraically (see appendix for demonstration).
In atmospheric sciences the water content varies from 0 to 5% ( Wallace & Hobbs, 2006),
however in stack emissions the moist content varies from 10% (in boilers) to 100%
(reactor exhaust).

RESULTS

Equations 4, 10 and 12 can be used to provide additional insight in the calculations


of different properties of the moist air since they show the molecular weight of
water explicit and have more precision (Table 1).

Table 1 Equations used to compute moisture variables.

Quan
Usual Proposed
tity

Mois
t
mole Mα=Md1+0.608q��=�
Ma=(1−fH)Md + fHMwMa=(1-��)M� + ��Mw
cular �1+0.608�
weig
ht

Spec
ific
q=r1+r�=�1+� q=fHMw(1−fH)Md+fHMw�=�HMw1-����+����
Humi
dity

Mass
mixi
r=εPwPd�=����� r=fHMw(1−fH)Md�=����(1-��)��
ng
ratio

Wet
fract
ion
fH=nH20nH20+nair=VH20VH20+Vair=PH20PH20+Pair��=��20��20+����=��20
��20+����=��20��20+����

DISCUSSION

We commonly observe that for materials that are moistened with liquid water, it is
possible that the air contained in them can be displaced and therefore a gas is
replaced by a liquid making its weight to increase. An example is observed in the
wet fabric or in a wet sponge; however, that does not happen in gases since most
of the air molecules have a higher molecular weight than water. Thus, by including
water vapor in the air, the contribution of the vapor of water makes the density of
the wet air mass to decrease. This can be seen in equation 4 and with Figure 1.
Moreover, calculating the density of that air mass using equation 6 it can be
identified that moisten air has a lower density. In nature this can be found when
water vapor rises until it reaches a condensation temperature, starting the
formation of clouds.

In our teaching experience, we observe that this set of equations help the students
to identify the contribution of water vapor in calculating the molecular weight,
density and humidity of the air.

CONCLUSION

The new procedure presented in this study for estimating humidity has several
advantages for students. By using Avogadro’s and general gas’ law, the equations
become algebraically equivalent to the traditional equations, but the use of the
symbol “ε” is avoided. This new method offers a different perspective for students
to understand the properties of moist air and can be used as a complement to the
traditional approach in lessons related to this topic. These equations can help
students to better understand the concepts of humidity and gas laws, providing a
more comprehensive understanding of the topic. Overall, this fresh approach offers
a useful and effective tool for educators to teach and explain humidity to students
concisely and helping to engage students and enhance their learning experience.

REFERENCES

Jacobson, M. Z. (1999). Fundamentals of atmospheric modeling. Cambridge


University press. [ Links ]

Perry, R. H., Green, D. W., & Maloney, J. (1997). Perry’s Chemical Engineers’
Handbook (ed.). Seventh, International edition. [ Links ]

Stull, R. (2015). Practical meteorology. An algebra-based survey of atmospheric


science. University of British Columbia, Columbia. [ Links ]

Wallace, J. M., & Hobbs, P. V. (2006). Atmospheric science: an introductory


survey (second ed., Vol. 92). Elsevier. [ Links ]
Cómo citar: Almanza Veloz, V. y García Reynoso, J. A. (2023, octubre-diciembre).
A different approach to estimate air moisture. Educación Química, 34(4).
https://doi.org/10.22201/fq.18708404e.2023.4.83628

APPENDIX

Demonstration of the equivalence of Equation 10 and 14

q=fHMw(1−fH)Md+fHMw�=�HMw1-����+���� (10)

Multiplying by P/P

q=fHMw(1−fH)PMd+fHMw�=�HMw1-�����+����

Considering that water vapor partial pressure: Pw=fHP and dry air partial pressure
Pd=(1-f H)P and substituting

q=PwMwPdMd+PwMw�=�wMw�dMd+����

Multiplying by M−1dM−1d��-1��-1

q=MwMdPwMdMdPd+MwMwPw�=�w�dPw�d�dPd+�w�wPw

Substituting ε=Mw/Md

q=εPwPd+εPw�=�����+���

Multiplying by P−1dP−1d��-1��-1

q=εPwPdPdPd+εPwPd�=���������+�����

Using equation 13 (r=εPw/Pd ) we obtain equation 14

q=r1+r�=�1+�

Received: October 17, 2022; Accepted: April 18, 2023

This is an open-access article distributed under the terms of the Creative Commons
Attribution License

Circuito interior s/n, Ciudad Universitaria, A.P. 70-197, Ciudad de México, Ciudad
de México, MX, 04510, (52-55)5622-3439

martina@una

You might also like