PCC Manual
PCC Manual
PCC Manual
Your new NC-PCC is ready to use right out of the box, but before you
get started, please carefully study and diligently practice the safety
and operational procedures outlined in this instructional manual.
Doing so will ensure years of reliable service while maintaining a safe
and enjoyable shooting experience for yourself and those around you.
LIMITATION OF LIABILITY
1
Warranty Information
NO WARRANTY CARD HAS BEEN INCLUDED WITH THIS NEW NORDIC
COMPONENTS PRODUCT
The Magnuson-Moss Act (Public Law 93-637) does not require any
seller or manufacturer of a consumer product to give a written
warranty. It does provide that if a written warranty is given, it must
be designated as “limited” or as “full” and sets minimum standards for
a “full” warranty. Nordic Components, Inc. has elected not to provide
any written warranty, either “limited” or “full”, rather than to attempt
to comply with the provisions of the Magnuson-Moss Act and the
regulations issued thereunder. There are certain implied warranties
under state law with respect to sales of consumer goods. As the
extent and interpretation of these implied warranties varies from
state to state, you should refer to your state’s law.
Questions/Concerns
If, at any time, you are unclear on any of the safety or operational
procedures discussed in this manual or are having difficulties with
your firearm, please contact Nordic Components, Inc. for assistance at
952-442-8900 or email sales@nordiccomp.com. Our customer service
and technical support departments are available to you should you
have any questions or concerns.
Problems/Returns
We make every effort to supply products in the best possible
condition; however, issues can arise from time to time. If there is a
problem with our product, or if a shipment was damaged in transit,
call us immediately for assistance and instructions at 952-442-8900.
Remember that it is illegal to ship a firearm and ammunition in the
same package. Ammunition must be shipped separately.
2
ATTENTION:
EYE AND EAR PROTECTION IS STRONGLY RECOMMENDED
WHEN ENGAGED IN, OR SIMPLY OBSERVING, SHOOTING
ACTIVITIES. RICOCHETS ARE COMMONPLACE AND
CAN TRAVEL GREAT DISTANCES OUTSIDE OF AN
OTHERWISE CONTROLLED SHOOTING AREA. IT IS HIGHLY
RECOMMENDED THAT EYE PROTECTION BE WORN AT ALL
TIMES AND IN ALL AREAS OF THE FIRING RANGE.
ATTENTION:
USE ONLY HIGH QUALITY, COMMERCIALLY PRODUCED,
AMMUNITION IN THE APPROPRIATE CALIBER FOR THIS
FIREARM. THE AMMUNITION MUST MATCH THE CALIBER
MARKED ON THE BARREL OF THE FIREARM. DO NOT USE
CARTRIDGES WITH SHARP SHOULDERED OR “EXPLOSIVE”
BULLETS.
WARNING:
CARELESS OR NEGLIGENT HANDLING, OR FAILURE TO
FOLLOW THE RECOMMENDED SAFETY PROCEDURES
OUTLINED HEREIN, MAY RESULT IN DAMAGE TO
PROPERTY, SEVERE INJURY, OR DEATH. ANY RESULTING
DAMAGE TO THE FIREARM IS NOT COVERED UNDER
WARRANTY BY NORDIC COMPONENTS, INC.
WARNING:
DO NOT, UNDER ANY CIRCUMSTANCES, ATTEMPT TO
ALTER OR MODIFY YOUR FIREARM OR PERFORM SERVICE
BEYOND GENERAL MAINTENANCE. DOING SO MAY VOID
YOUR FACTORY WARRANTY AND JEOPARDIZE YOUR
SAFETY. PLEASE CONTACT NORDIC COMPONENTS, INC. IF
THERE IS A PROBLEM.
3
WARNING:
DISCHARGING FIREARMS IN POORLY VENTILATED AREAS,
CLEANING FIREARMS, OR HANDLING AMMUNITION MAY
RESULT IN EXPOSURE TO LEAD AND OTHER SUBSTANCES
KNOWN TO CAUSE BIRTH DEFECTS, REPRODUCTIVE
HARM, AND OTHER SERIOUS PHYSICAL INJURY. HAVE
ADEQUATE VENTILATION AT ALL TIMES AND WASH
HANDS THOROUGHLY AFTER EXPOSURE.
WARNING:
UNFIRED ROUNDS MAY NOT ALWAYS EJECT OUT OF THE
FIREARM’S CHAMBER. ALWAYS VISUALLY CHECK TO SEE
THAT THE CHAMBER IS CLEAR!
4
Safety
ALWAYS keep your finger off of the trigger and out of the
trigger guard until the firearm is intentionally pointed
downrange at a verified target, in front of a suitable
backstop, and you are ready to fire.
5
SAFETY IS CRITICAL TO PERFORMANCE
Your Nordic rifle is only as good as the hands that hold it.
You can never be too careful. Frequently, firearms accidents are the
result of carelessness or inattentiveness such as failing to control the
direction of the muzzle, failing to properly engage the safety, leaving
the rifle loaded or using improper ammunition. This carelessness can
result in the destruction of life, limb or property. The principles of safe
firearm handling and storage must be known before you unpackage
your rifle; there are no do-overs.
Function and performance of your firearm depends on proper
use and maintenance, so the information in this instruction book must
be known and understood. Not all firearms are the same, and there
can be new information for even the most experienced firearms owner.
To handle your firearm safely, you must first learn the features and
requirements of your new rifle.
The Ten Commandments of Firearm Safety should be etched
in your memory forever and should dictate your action anytime you’re
involved with firearms. Take the time to review and understand these
rules.
6
2nd Commandment: Firearms should be unloaded when not actually
in use
Load your firearm only when you’re in the field or on the range
and ready to fire. Never let a loaded firearm out of your sight or out of
your hands. Unload it as soon as you’re finished shooting. Remember,
unloading your firearm means unloading it completely, so there is
no ammunition in the chamber or in the magazine. Before handling
a firearm or passing it to someone else, visually check the chamber,
receiver and magazine to be certain they do not contain ammunition.
Always keep the firearm’s action open when not in use. Never assume
a firearm is unloaded -- always check for yourself.
• Let common sense rule when you carry a loaded firearm. If you’re in
a situation that could risk accidental discharge - such as crossing a
fence, wading through a stream or climbing a tree - always unload your
firearm. Never pull or push a loaded firearm toward yourself or another
person. Never carry a loaded firearm in a scabbard, detached holster or
gun case.
• Certain firearms are equipped with internal security devices to
prevent unauthorized use. In addition, some firearms owners use
external devices, such as cable locks and trigger blocks, for the same
purpose. Even if you use such a device, you should still keep your
firearm unloaded when stored or not in use. Internal or external
devices cannot substitute for securing your firearms and ammunition
in a separate, locked location.
• Safe storage of firearms is just as critical as safe handling. Never
store firearms loaded. Be sure to keep your firearms in a secure place
where unauthorized persons cannot get their hands on them without
your knowledge.
• Take special care if there are children around. Children are fascinated
by firearms. It’s a natural curiosity that can have tragic consequences
when not properly supervised. Store your firearms in a locked gun safe
or some other location that physically bars a child from gaining access.
• Ammunition should be stored and locked in a location separate
from your firearm. Never leave an unsecured firearm or ammunition
in a closet, dresser drawer or under the bed. Remember, it is your
responsibility to make sure that children and others unfamiliar with
firearms cannot get access to your firearm and ammunition.
7
3rd Commandment: Don’t rely on your firearm’s safety.
Once you pull the trigger, you can never call that bullet back. Never
fire unless you know exactly where your shot is going and what it will
strike. Never fire at a sound, a movement or a patch of color. A hunter
in camouflage can easily be mistaken for a target by an impulsive
shooter.
Before you pull the trigger be absolutely sure of your target
and what’s behind it. Make sure the shot has a backstop such as a
hillside or dense material like sand. Remember, bullets can travel
great distances with tremendous velocity.
Be sure to know where your shot might go if you miss the
target or if the bullet is not stopped by the target.
Be aware and mindful of the possibility of ricochets; never
shoot at a hard surface or water.
Know how far your shot will go if you miss your target or the
bullet ricochets.
8
5th Commandment: Use proper ammunition.
If for some reason the ammunition doesn’t fire when you pull
the trigger, stop and remember the 1st Commandment of Firearm
Safety - always keep the muzzle pointed in a safe direction. Keeping
your face and hands away from the breech as much as possible,
put the safety on, carefully open the action, unload the firearm and
dispose of the cartridge safely. Anytime there’s a shell in the chamber,
your firearm is loaded and ready to use, and could still discharge.
Your sight and hearing risk injury from shooting and should
be protected at all times. Wear protective shooting glasses to guard
against powder residue, ruptured cartridge cases, and debris in the
field. Always wear eye protection when you’re disassembling or
cleaning a firearm so that tensioned parts and cleaning products don’t
come in contact with your eyes.
Unprotected exposure to shooting noise will permanently
damage your hearing. On the range, be sure to use protective earmuffs
or earplugs. Learn to use ear protection at all times. Only discharge
your firearm in well-ventilated areas.
9
8th Commandment: Be sure the barrel is clear of obstructions before
shooting
Before loading your firearm, open the action and make sure
the chamber and magazine are empty. Check the barrel for any
obstructions or debris. Even a small amount of snow, mud, or excess
lubricant or grease in the bore can dangerously increase pressure
and cause the barrel to bulge or burst when firing. Use a cleaning rod
and patch to wipe away anti-rust compounds or any other residues or
obstructions in the barrel. Never try to shoot out an obstruction by
loading another shell and firing!
When firing, rely on your instincts. If the noise or recoil of your
firearm seems weak, unload your firearm and be sure nothing is lodged
in the barrel. Always be sure you’re using the correct ammunition in
your firearm and that it’s free of obstructions.
10
For safe and dependable operation of your firearm, all parts
of your firearm must be properly cleaned and lubricated. Periodically
inspect the internal workings of your firearm to be sure they’re clean
and free of rust, dirt, and debris.
Use recommended lubricants on your firearm and do not
over-lubricate. Excessive use of a non-recommended lubricant could
adversely affect the function and safe operation of your firearm.
Failure to properly maintain your firearm cannot only damage
your firearm, it can cause personal injury or death.
There’s one other rule that must be followed when handling firearms.
Respect for this rule is necessary in order to effectively practice the
Ten Commandments of Firearm Safety. The rule is: SHOOT SOBER!
Firearms and alcohol or drugs make a deadly combination. Never
consume anything that would impair your judgment or physical
coordination when you’re using a firearm. A large number of the
shooting accidents that occur involve alcohol or drugs. Be smart.
Always shoot sober and stay alive.
LEAD WARNING
Discharging firearms in poorly ventilated areas, cleaning firearms,
or handling ammunition may result in exposure to lead and other
chemicals known to cause birth defects, reproductive harm, cancer,
and other serious physical injury. Have adequate ventilation at all
times. Wash hands thoroughly after exposure.
11
NC-PCC Features & Operation
Interchangable Magwells
The NC-PCC features an innovative modular magwell system. By
simply changing out magwells, the NC-PCC can accept a variety of
handgun magazines. See www.nordiccomp.com for a complete list of
available platforms.
Magazines
Only OEM magazines (specific to the magwell installed) are
recommended for use in the NC-PCC. Other magazines may function
with the firearm, but reliable operation cannot be guaranteed by
Nordic Components.
Muzzle Threading
The NC-PCC features a caliber-appropriate threaded barrel, designed
to accept a variety of muzzle devices.
General Operation
The NC-PCC is a blowback operated firearm, using the energy of the
fired round is used to cycle the action. Because of this, the NC-PCC
does not have a gas system. As the weight of the bolt and buffer,
along with the strength of the buffer spring, are critical to reliable
operation, any modification or change of any these components
will impact function and safety of the firearm. Nordic Components
recommends using only OEM components and cannot guarantee
function or operator safety with aftermarket or modified parts.
12
Changing Magwells
• Pull back the charging handle and look in the ejection port to verify
that the chamber is empty.
• Push the magwell retaining pin to the left and pull it out until the
pin stops.
MAGWELL PULLS
FORWARD, DROPS
DOWN
MAGWELL PIN
13
If you are changing to a magwell that requires a different bolt catch
lifter, the upper receiver must be removed using the following steps:
• Push the takedown pin to the left and pull it out from the right until
the pin stops (note that this will allow the upper receiver to pivot
forward; ensure the handguard/barrel are supported).
• Push the pivot pin to the left and pull it out from the right until the
pin stops. Remove the upper receiver from the lower receiver. The
lifter is captured under the bolt catch, which must be depressed to
remove the lifter.
• To reinstall the lifter, push the bottom of the bolt catch to raise the
catch and slide the short arm of the lifter underneath, so that the
short arm can raise the catch.
• Slide the long arm of the lifter into its slot in the lower receiver and
align the pivot pin hole on the arm with the holes in the pivot pin
bosses.
• Reinstall the upper receiver, and push the pivot pin back into place.
Ensure the lifter remains properly aligned with the pivot pin, or the pin
will not seat fully.
14
Lower Receiver
15
OPERATION OF THE NC-PCC
Detailed instructions about the function and use of your NC-PCC.
5. Hold down the lower portion of bolt catch and allow bolt to move
forward until it engages bolt catch. Return charging handle to forward
position. Make sure the safety selector lever is on SAFE.
16
Preventative Maintenance Checks & Services
2. Retract the bolt to ensure free movement of the bolt and charging
handle.
3. Place safety selector lever in FIRE position. Pull the trigger. THE
HAMMER SHOULD FALL.
4. Hold trigger to the rear, pull charging handle to the rear and release
charging handle. Then release pressure on the trigger with a slow,
smooth motion, without hesitations or stops, until the trigger is fully
forward. AN AUDIBLE CLICK SHOULD BE HEARD - THE HAMMER
SHOULD NOT FALL.
5. Repeat this safety function test FIVE TIMES. The firearm must not
malfunction during any of these five tests. If the firearm malfunctions
during any of these tests, stop using the firearm and have it serviced
by a gunsmith or contact Nordic Components.
17
Loading, Firing, and Unloading
• Holding the magazine upright and with the bullet facing forward,
position the cartridge on top of the follower, ahead of the feed lips
(The follower and top of magazine should angle upwards toward the
front of the magazine).
• Press down and back on the cartridge with your thumb so that the
rear of the case clears the feed lips and slides fully to the rear.
• Pick up the firearm, keeping your finger off of the trigger and out of
the trigger guard.
• Disengage the charging handle latch and pull the charging handle
fully to the rear.
• While holding the handle back, look in through the ejection port and
visually verify that the chamber is clear. If clear, release the charging
handle so the bolt closes. The hammer will be cocked during this
process.
PULL BACK
EL
O LT TRAV
B
• You should now flip the safety selector to the “SAFE” position.
19
• Verify that the magazine is fully seated by gently pulling down on
the magazine. If fully seated, the magazine will remain locked in
place.
• If the bolt is locked back, push the upper portion of the bolt
release. The bolt should spring forward, chambering a round from the
magazine and making the firearm ready to fire.
• If the bolt is forward, pull the charging handle fully to the rear, then
release the charging handle, allowing the bolt to spring forward. This
will chamber a round from the magazine and the firearm will be ready
to fire. Never “ride” or “push” the charging handle forward; let the
charging handle and bolt move forward under their own power.
RELEASE
EL
TRAV
BOLT
CONDITION: The firearm is now loaded and ready to fire, with the
hammer cocked and a live round in the chamber. The safety selector
should be on SAFE.
20
Firing Your NC-PCC
2. Making sure of your target and what is beyond it, take aim at the
target.
3. Squeeze the trigger until the trigger “breaks” and the cartridge is
fired. Once the cartridge has fired, release the trigger.
NOTE: After the last round in the magazine has been loaded and fired,
the bolt will lock to the rear. You can then insert a new magazine and
either push the bolt catch release button or cycle the charging handle
to chamber a new round and resume firing.
Cooking off means that a round may detonate from the heat of the
rifle’s chamber.
21
Unloading Your NC-PCC
3. Pull the charging handle to rear. Press the lower portion of the bolt
catch; the bolt should lock open as the handle is released. If a round
was in the chamber, it should have been ejected.
4. Visually check the chamber through the ejection port to make sure
the chamber is empty.
5. With the magazine removed and the chamber empty, close the bolt
by pushing the top of the bolt catch to allow the bolt to return forward
on the empty chamber.
22
Remedial Actions
2. Pull charging handle all the way back. Observe the ejection of the
case or cartridge. Check chamber for any obstruction.
NOTE: If pulling the charging handle fully to the rear does not extract
and eject the chambered cartridge or case, then the cartridge or
casing may be stuck in the chamber. If this occurs do the following:
23
Bullet Stuck in the Bore
Upper Disassembly
2. Push in takedown pin (a punch may help) as far as it will go. Pivot
upper receiver from lower receiver.
3. Push in pivot pin (note: take care that the bolt catch lifter is not
lost, as it will be loose once the pivot pin is pushed in)
5. Slide the charging handle back part-way and remove the bolt.
24
7. To remove the firing pin, first remove the firing pin retainer. This
can be pushed from right to left using a punch or similar tool. This will
release the spring-loaded firing pin -- ensure that you have control of
the assembly and that the pin/spring are not lost.
8. To separate the bolt halves, use a punch to depress the bolt index
pin at the rear of the front half. With the index pin depressed, the bolt
tail can be rotated 90 degrees and removed to allow easier access to
the bolt for cleaning.
Maintenance Overview
After firing your rifle, clean it as soon as possible to make the job
easier and to avoid allowing the development of any corrosion.
When your firearm has not been fired, you should clean it once or
twice a year if you live in a temperate climate, or as often as once a
week in a tropical climate. If you get your firearm wet, clean it as soon
as possible to avoid the onset of corrosion or rust.
After you have disassembled the rifle, thoroughly clean, inspect and
lubricate all parts according to the techniques described below.
WARNING
25
Detailed Cleaning Techniques
The bore of your Nordic Components NC-PCC has lands and grooves
called rifling. Rifling makes the bullet spin as it moves down the bore
and down range. It is difficult to push a new, stiff bore brush through
the bore. You will find it much easier and more effective to pull the
brush through the bore.
Also, because the brush will clean better if the bristles follow the
grooves, the brush should be allowed to turn as it travels through
the bore. A high quality cleaning rod with a ball bearing handle which
allows the rod to turn will assist in cleaning your rifle.
Do not use a steel cleaning rod, as this can permanently damage the
bore.
ALWAYS CLEAN FROM CHAMBER TOWARD THE MUZZLE.
2. Pointing the muzzle down, hold the upper receiver in one hand
while inserting the end of the rod with patch holder attached into the
chamber. Carefully guide the rod through the bore.
CAUTION: Do not let the rod or its threaded end scratch the bore or
chamber.
3. Moisten a patch with bore cleaner and run it through the bore.
5. Push the brush through the bore and out the muzzle. The rod should
turn as you push it through - as described earlier, this is the brush
“tracking” in the rifling. NEVER reverse the direction of the bore brush
while it is in the bore.
26
6. After running the brush through the bore several times, the rod
(or rod sections) and the bore brush may become screwed tightly
together. If so, loosen the components and continue running the
brush through the bore.
7. Run a patch through the bore occasionally while using the brush
to help clean out debris. Just replace the bore brush with the rod tip
(patch holder) and a wet patch. Always have the bore wet with cleaner
before trying to pull a brush through.
NOTE: Check to ensure that the fit between the barrel and the upper
receiver is tight - if you detect any movement by twisting with your
hands, the barrel nut must be retorqued. Take the rifle to a qualified
gunsmith or contact Nordic Components for such maintenance.
1. Using a high quality cleaner, clean the inside and outside of the
upper receiver of powder fouling, corrosion and dirt. NEVER use a wire
brush or any type of abrasive to clean the aluminum upper receiver -
you may damage the finish. A toothbrush or stiff-bristled nylon brush
is good for loosening any dirt buildup, and won’t scratch the receiver.
2. Clean the chamber. Dip a chamber brush in bore cleaner and use at
least five plunge strokes and three 360° clockwise rotations. Swab out
the bore as described previously to remove solvent and debris.
3. Use the damp bore brush to clean carbon and powder residue from
the inside of the upper receiver.
4. Using a cloth moistened with solvent, wipe the bolt assembly clean
of any fouling, paying special attention to the bolt face.
5. Wipe all components clean and dry, and inspect for excessive wear,
corrosion or mechanical damage. If you notice any excessive wear or
damaged components, DO NOT USE THE FIREARM. Have the firearm
inspected by a gunsmith or contact Nordic Components.
27
Cleaning the Lower Receiver
2. Wipe any fouling or dirt from the fire control group. Carefully clean
the magazine release button and the magazine catch on the left side
of the receiver.
3. Inspect and clean the bolt catch and takedown/pivot pins. Check
to ensure that the bolt catch lifter arm is not dirty or damaged and
that it can travel freely.
4. Push down on the buffer retainer and remove the buffer assembly.
Clean inside the receiver extension and ensure that the buffer and
spring are free of fouling or corrosion.
5. If the collapsible stock does not move freely, remove it from the
receiver extension and clean the tube and lock holes. Lightly lubricate
the receiver extension and stock latch mechanism.
Lubrication
Lower receiver: Lightly lubricate the inside and outside of the receiver
extension, the buffer, buffer spring, and stock latch. Generously
lubricate all moving parts inside the lower receiver, including the
trigger, hammer, safety, bolt catch, magazine release, etc., and their
respective pins and detents. Lubricate the takedown, pivot, and
magwell pins and their detents. Use a lightly oiled rag to wipe down
the exterior surfaces.
Upper receiver: Lightly lubricate the firing pin and firing pin channel.
Generously lubricate the bolt and charging handle surfaces. Use a
lightly oiled rag to wipe down the exterior surfaces.
28
Reassembly
1. Insert the buffer spring and buffer (the spring will “lock” around the
buffer if you slide the spring on and turn counterclockwise). Depress
the buffer detent and push the buffer past the detent, then release.
2. Insert the bolt alignment spring and pin, and align the tabs in the
bolt head with the slots on the bolt tail. Once the tabs are aligned, use
a punch to push down on the alignment pin and rotate the bolt head
until the pin locks the two halves together.
3. Insert the firing pin spring and firing pin. Apply pressure to the
firing pin until the firing pin retainer can be pushed completely into its
channel.
4. Align the charging handle ears with the cutout in the upper receiver
and slide the charging handle in part-way. Insert the bolt into the
upper receiver, with the gas key in the charging handle groove. Push
the bolt forward and lock the charging handle forward.
NOTE: If the ejection port door is closed, there will be some resistance
as the bolt passes the door and pushes it open.
5. To join upper and lower receivers, position the pivot pin lug of the
upper receiver between the pivot pin bosses at the front of the lower
receiver and push the pivot pin into place.
NOTE: Take care that the bolt catch lifter is properly aligned with the
pivot pin before pushing the pin into place.
6. After the pivot pin is in place, lower the upper receiver so that the
takedown pin lug slides into place at the rear of the lower receiver and
push the takedown pin into place.
NOTE: The pivot, takedown, and magwell pins are held captive in the
lower receiver, meaning they are held in by their detents and springs
so they cannot fall out and get lost.
29
NC-PCC Parts List/Exploded View Reference
1 NC PCC LOWER RECEIVER 39 DUST COVER PIN
2 PISTOL GRIP 40 FORWARD ASSIST ROLL PIN
3 BOLT CATCH SPRING 41 CRUSH WASHER
4 BOLT CATCH PLUNGER 42 FORWARD ASSIST SPRING
5 BOLT CATCH 43 HANDGUARD COUNTERBORED
6 PIVOT PIN INSERT
7 TAKEDOWN PIN 44 HANDGUARD THREADED
8 HAMMER INSERT
9 TRIGGER 45 HANDGUARD FASTENER
10 BOLT CATCH LIFTER 46 DUST COVER SPRING
11 ENDPLATE 47 PCC MAG WELL
12 CARBINE BUFFER TUBE 48 PCC MAG CATCH
13 BUFFER RETAINER SPRING 49 MAG CATCH SPRING
14 BUFFER RETAINER 50 PCC EJECTOR
15 BUFFER SPRING 51 MAG RELEASE PIN
16 BUFFER ASSEMBLY 52 MAG RELEASE PIN RETAINER
17 HAMMER/TRIGGER PIN 53 EJECTOR SCREW
18 SELECTOR DETENT 54 NC9 BOLT FRONT
19 TAKEDOWN PIN DETENT PIN 55 NC9 BOLT REAR
20 MAGWELL SPRING PLUNGER 56 NC9 CARRIER KEY
21 CASTLE NUT 57 NC9 EXTRACTOR
22 MAGWELL DETENT RETAINER 58 NC9 FIRING PIN
23 TRIGGER SPRING 59 FIRING PIN SPRING
24 HAMMER SPRING 60 FIRING PIN RETAINER
25 DISCONNECTOR 61 BOLT ALIGNMENT PIN SPRING
26 BOLT CATCH PIN 62 EXTRACTOR PIN
27 SAFETY DETENT SPRING 63 EXTRACTOR PIN RETAINER
28 DISCONNECTOR SPRING 64 CARRIER KEY FASTENERS
29 MAG WELL PIN 65 BOLT ALIGNMENT PIN
30 SAFETY SELECTOR 66 EXTRACTOR SPRING W/
31 TAKEDOWN PIN SPRING BUFFER
32 UPPER RECEIVER
33 BARREL
34 BARREL NUT
35 MUZZLE DEVICE
36 HANDGUARD
37 FORWARD ASSIST
38 DUST COVER
30
8
31
24
25
14 23
16 28
30
15
13 5
21
NC-PCC Lower Receiver Assembly
19 22
9 31
10
31 19
4
3
29
11
7 1
26
17
12
18
17 19
27
31
20
6
2
NC-PCC Lower Receiver Assembly
32
NC-PCC Upper Assembly
33
NC-PCC Magwell Assembly
50
52
47
51
53
48
49
34
64
35
58 56
NC-PCC Bolt Assembly
59
63
60
62
55 65
57
61
66 54
NC-PCC Bolt Assembly
CHARGING HANDLE
36
37
FORSERVICE,TECHNICALSUPPORT,ORWARRANTYISSUES,CONTACT:
NORDIC COMPONENTS
79 E. 8TH ST.
WACONIA, MN 55387
SALES: 952.442.8908
TECHNICAL SUPPORT: 952.442.8915
SALES@NORDICCOMP.COM