®

Wiring Device-Kellems

Hubbell Circuit-Lock®
Motor Disconnects
The Solution — No Matter what Environment or Application

A Safety-First Priority
www.hubbell.com
 Circuit-Lock® Switched Disconnect Enclosures: Non-Metallic Labelless
• Constructed from corrosion- and impact-resistant,
UV stabilized, engineered thermoplastic
• IP69k and Type 4X, 12K water ingress protection
• Certified by NSF for hygiene in food processing applications
• Adjustable mounting feet now 40% stronger to prevent
nuisance breakage
• Product ratings are permanently laser-marked
and will not wash off
• Truly captive screws prevent lost screws
• Shipped from factory as bottom feed for quicker installation
in 4X applications
• Reversible interior easily converts to allow top conduit opening
• Highly visible red handle which meets
OSHA Lockout/Tagout requirements
• Cover cannot be removed with switch in the “ON” position
• Accepts up to 2 Auxiliary contacts
• Ample gutter space for ease of installation

IP69k

HBLDS3
(Cover off)
HBLDS3
(Cover)
LED Indicators
• Six highly visible integral phase
identification LEDs
• External LEDs provide secondary means
of visual confirmation of make/break
on all phases

Jog Switch
• Convenience of having point of use control
circuit to PLC within sight of the motor
• Cost savings by utilizing existing space in the
motor disconnect enclosure, reducing parts
and labor costs
• Increased safety by allowing maintenance personnel
to “Try Out" after LO/TO

MotorQuick®
• Significantly reduces installation time
to replace motors with the plug-and-play
technology of the LINKOSITY® power system
• Motor rotation can be pre-checked
in a maintenance shop to further speed installation time

www.hubbell.com
2
 Circuit-Lock® Switched Disconnect Enclosures: Stainless Steel
• Formed in nonporous 304 stainless steel
• IP69k and Type 4X, 12K water ingress protection
• Certified by NSF for hygiene in food processing applications
• Fixed offset ¼ inch mounting feet meet NEC airspace
requirements for metal enclosures
• Labelless markings on the cover
• Cover cannot be removed with switch in the “ON” position
• Highly visible red handle which meets
OSHA Lockout/Tagout capabilities
• Accepts up to 2 Auxiliary contacts

More than ever, food and beverage processing

facilities see the value of investing in intelligent design
and following best practices in hygiene.
The sloped top enclosure is consistent with these best HBLDS3SS
practices: horizontal surfaces have been minimized to
assist with getting it clean, and keeping it clean.

HBLDS3SSR
IP69k

Housing Design
• 15° sloped top design sheds water, dust
and debris
• Fully shrouded handle prevents damage
• Captive screws prevent lost screws

Labor Savings
• 15º Sloped Top version available
pre-drilled with 3/4 inch stainless steel
hubs for bottom feed applications
• Ample gutter space for hassle-free installation

Variable Frequency Drive (VFD)

• Integrates a verified break before break
auxiliary contact factory installed in our
HBLDS series
• Prevents downtime from out of sequence
equipment shutdowns

www.hubbell.com
3
 Circuit-Lock® 30A Disconnects with LED Indicators

inSIGHT
TM

Insight (n): the power or act

of seeing into a situation
Hubbell’s new 30A Circuit-Lock Disconnect with integral
phase indication LEDs redefines the benchmark for safety
by providing insight into the enclosure while in use.
Six highly visible LEDs (3 line side/3 load side) display
the electrical status of the switch by phase. This voltage
detection feature significantly improves existing safety
and maintenance procedures by visually providing critical
information, such as a welded contact or dropped phase,
to personnel prior to removing the enclosure cover.
With an ever-growing focus on safety improvements,
Hubbell inSIGHT disconnects provide a difference
TM

you literally can see.

IP69k

Housing Design HBLDS3P

• 6 highly visible integral phase identification

LEDs provide secondary means of visual
confirmation of make/break on all phases
• Available in non-metallic, stainless steel
and jog switch versions
• IP69k and Type 4X, 12K water
ingress protection

Safety
• High visibility red handle can be locked
in the OFF position to comply with OSHA
Lockout/Tagout requirements
• Quickly upgrade the safety of existing
installations with an inSIGHT
TM

replacement cover
• Verification of opening of load side contacts

Unfused Disconnect Switches with LEDs

Stainless Steel
Description Non-Metallic Square Top Sloped Top
Disconnect switch with LEDs HBLDS3P HBLDS3SSP HBLDS3SSRP
30A Disconnect switch with
HBLDS3PAC — —
HBLAC1 auxiliary contact
Disconnect switch with LEDs HBLDS6P HBLDS6SSP HBLDS6SSRP
60A Disconnect switch with
HBLDS6PAC HBLDS6SSPAC HBLDS6SSRPAC
HBLAC1 auxiliary contact
Disconnect switch with LEDs HBLDS10P HBLDS10SSP HBLDS10SSRP
100A Disconnect switch with
HBLDS10PAC — —
HBLAC1 auxiliary contact
Note: For use with 3Ø Y configurations only.

www.hubbell.com
4
Ordering Information
Labelless Circuit-Lock® Switched Disconnect Enclosures
Non-Metallic
Description 30 Amp 60 Amp 100 Amp
Disconnect switch HBLDS3 HBLDS6 HBLDS10
Disconnect switch with HBLAC1 auxiliary contact HBLDS3AC HBLDS6AC HBLDS10AC
Disconnect switch for use with variable frequency drives HBLDS3VFD HBLDS6VFD HBLDS10VFD
Disconnect switch without conduit knockout or HBLDS3NK — —
conduit fitting
Disconnect switch with HBLAC1 auxiliary contact without HBLDS3ACNK — —
conduit knockout or conduit fitting
Disconnect switch with 3 auxiliary contacts, without conduit HBLDS33ACNK — —
knockouts. Break before main break – 1 set “normally open,”
1 set “normally closed” Break after main break – 2 sets
“normally open,” 1 set “normally closed”

Stainless Steel
Description 30 Amp 60 Amp 100 Amp
Square Top disconnect switch HBLDS3SS HBLDS6SS HBLDS10SS
Square Top disconnect switch with HBLAC1 HBLDS3SSAC HBLDS6SSAC HBLDS10SSAC
Square Top disconnect switch for use with HBLDS3SSVFD HBLDS6SSVFD HBLDS10SSVFD
variable frequency drives
Sloped Top disconnect switch HBLDS3SSR HBLDS6SSR HBLDS10SSR
Pre-drilled Sloped Top disconnect, 4X, with 2 - ¾" SS Hub HBLDS3SSR2K — —
Sloped Top disconnect switch with HBLAC1 HBLDS3SSRAC HBLDS6SSRAC HBLDS10SSRAC
auxiliary contact
Sloped Top disconnect switch for use with HBLDS3SSRVFD HBLDS6SSRVFD HBLDS10SSRVFD
variable frequency drives
Sloped Top enclosure, Blank HBLDSSRNK3 HBLDSSRNK6 —

Labelless Disconnects with Jog Switch

Non-Metallic
Description 30 Amp 60 Amp 100 Amp
Disconnect switch HBLDS3J HBLDS6J HBLDS10J
Disconnect switch with HBLAC1 auxiliary contact HBLDS3ACJ — —
Disconnect switch for use with variable frequency drives HBLDS3VFDJ — —
Disconnect with Jog switch and LEDs HBLDS3PJ HBLDS6PJ HBLDS10PJ

Stainless Steel
Description 30 Amp 60 Amp 100 Amp
Square Top disconnect HBLDS3SSJ HBLDS6SSJ HBLDS10SSJ
Square Top disconnect with Jog switch and LEDs — HBLDS6SSPJ HBLDS10SSPJ
Sloped Top disconnect HBLDS3SSRJ HBLDS6SSRJ HBLDS10SSRJ
Sloped Top disconnect with Jog switch and LEDs HBLDS3SSRPJ HBLDS6SSRPJ —

Auxiliary Contacts for 30, 60 and 100 Amp Switch, NEMA A600 Pilot Duty
Description Catalog Number
“Break After Main Break,” 1 set of n/o contacts, 1 set of n/c contacts HBLAC1**
“Break Before Main Break,” 1 set of n/o contacts for use with variable frequency drives HBLAC2**
Note: *Certified by NSF, International. | **Up to two auxiliary contacts per enclosure. Not for use with HBLDS33ACNK. | 30A units are
supplied with (1) ¾ in. NPT Raintight conduit fitting. | 60A & 100A units are supplied with (2) 1¼ in. NPT Raintight conduit fittings.

Upgrade safety of existing installations

with an inSIGHT ™ replacement cover
Non-metallic Stainless Square Stainless Sloped
30A HBLDS3RCP HBLDS3SSRCP HBLDS3SSRRCP
60A HBLDS6RCP HBLDS6SSRCP HBLDS6SSRRCP
100A HBLDS10RCP HBLDS10SSRCP HBLDS10SSRRCP

HBLDS3 HBLDS3SSJ HBLDS3SSRP

www.hubbell.com
5
 MotorQuick® Disconnect Switches
• NEMA 1 and Type 4x versions
• Plug-and-play design allows for faster installation
• Reduces motor change-out time by more than 65%,
providing productivity and bottom-line savings
• Crush and impact resistant MC cables
• Features high visibility lockable handles to meet
OSHA Lockout/Tagout regulations

Drastically reduces total cost of ownership HBLDS3MQR

by minimizing downtime of critical motors. Reduce motor change-out
time by more than 65%! HBLDS3MQ5

IP67
SUITABILITY

MotorQuick® Disconnect Switches

Type 1 Non-Metallic Enclosure: 30A 3 Pole 600V AC Catalog Number
HBL1389D with one pre-wired LINKOSITY female receptacle (load side) HBL1389MQR
®

HBL1389D with 5 foot pre-wired LINKOSITY® female cable (load side) HBL1389MQ5
HBL1389D with one pre-wired LINKOSITY® male receptacle (line side) HBL1389MQR2
and one pre-wired LINKOSITY® female receptacle (load side)
Type 4X Non-Metallic Enclosure: 30A 3 Pole 600V AC
HBLDS3 with one pre-wired LINKOSITY® female receptacle (load side) HBLDS3MQR
HBL1389MQ5
HBLDS3 with 5 foot pre-wired LINKOSITY® female cable (load side) HBLDS3MQ5
HBLDS3 with one pre-wired LINKOSITY® male receptacle (line side) HBLDS3MQR2
and one pre-wired LINKOSITY® female receptacle (load side)
Accessories
3P 4W LINKOSITY® male receptacle for installation on motor RM3004PA001
3P 4W LINKOSITY® double ended (male/female) 5-50 foot cable PH3004PAxxx*
Lock-on cover for LINKOSITY® connections PH2030C HBL1389MQR2
Note: *Cables available from 5-50 feet in 5 foot increments.
To purchase larger cable, replace the xxx with the required length in feet.
(Examples: PH3004PA005 = 5 foot cable, PH3004PA015 = 15 foot cable.)

MotorQuick® Cost of Ownership Analysis

Traditional Motor Changeout
Total Material Labor Total Labor Downtime Total Downtime
Catalog Number Cost Cost/ Hr Downtime Cost Cost/hr Cost Total Cost
HBL1389D $106.00 $53.00 1 hour $53.00 $750.00 $750.00 $909.00
HBLDS3 $185.00 $53.00 1 hour $53.00 $750.00 $750.00 $988.00

MotorQuick® Motor Changeout

Total Material Labor Total Labor Downtime Total Downtime Total
Catalog Number Cost Cost/ Hr Downtime Cost Cost/hr Cost Total Cost Savings
HBL1389MQ* $299.00 $53.00 20 min. $17.67 $750.00 $250.00 $566.67 $342.33
HBLDS3MQ* $411.00 $53.00 20 min. $17.67 $750.00 $250.00 $678.67 $309.33
Note: *MotorQuick catalog numbers are based on the average cost of the various designs.

www.hubbell.com
6
 Circuit-Lock® 200A Disconnect Switches
• UL 98 Rated Switch
• Available in Non-Metallic and Stainless Steel versions
• UL Listed Type 4X, 12 enclosure
• Accepts up to 2 Auxiliary Contacts
• Highly visible red rotary handle is compliant
with OSHA Lockout/Tagout
• Cover cannot be removed with switch in the “ON” position
• 200kA SCCR Rating when Protected by a Class “J” Fuse

Designed to withstand harsh industrial environments

with exposure to water, chemicals, oils and frequent washdowns.
HBLDS20

HBLDS20SS

Circuit-Lock® 200A Disconnect Switches

Description Catalog Number
200A non-metallic disconnect HBLDS20
200A stainless steel disconnect HBLDS20SS
N/O auxiliary contact - “Break Before Main” HBLAC200
200A replacement switch HBLDS20RS
200A replacement handle HBL200HDL

Fused Disconnect Switches

3 Pole 600V AC
Amp Description Catalog Number
30 Circuit-Lock fused disconnect switch FDS30*
60 Circuit-Lock fused disconnect switch FDS60*
Auxiliary contact, normally open, A600 pilot duty HBLACFSNO
Auxiliary contact, normally closed, A600 pilot duty HBLACFSNC
Note: *Class "J" fuse not included.

HBLACFSNO

FDS60

www.hubbell.com
7
 Twist-Lock® Mechanical Interlock Switched Safety Enclosures
• Mechanically interlocked to prevent mating and breaking under load
• Switch cannot be turned "ON" unless the plug is properly inserted and locked,
and the plug cannot be removed until the switch is turned "OFF"
• Switched enclosures sold separately from receptacle for custom electrical configurations
• Type 4X rated system with and without the shrouded watertight plug inserted
• Horsepower rated switch
• Enclosure is designed for top, bottom or back feed options

HBLMITL (enclosure)
Switched Safety Enclosures (Receptacles Sold Separately, See Below) with HBL2320SW (receptacle)
Description Ratings Catalog Number & HBL2621S (plug)
Mechanical Interlock, accommodates Amperage and voltage ratings determined by the HBLMITL
20A or 30A Watertight Safety-Shroud® Watertight Safety-Shroud® Twist-Lock® selected.
Twist-Lock® receptacles. Supplied with ¾" N.P.T. Hub.

HBLMITL Accepts the Following Watertight Safety-Shroud® Twist-Lock® Receptacles:

NEMA Config. Max. HP
Amp Poles/Wires Voltage AC Ref. Number Rating* Receptacle Mating Plug
120 L5-20 1 HBL2310SW HBL2311SW
2 Pole,
208-240 L6-20 2.5 HBL2320SW HBL2321SW
3 Wire
277 L7-20 3 HBL2330SW HBL2331SW
HBL2321SW
20 120/240 L14-20 2.5 HBL2410SW HBL2411SW
3 Pole,
240 3Ø L15-20 5 (3@208V) HBL2420SW HBL2421SW
4 Wire
480 3Ø L16-20 10 HBL2430SW HBL2431SW
4 Pole, 5 Wire 120/208 3ØY L21-20 3 HBL2510SW HBL2511SW
2 Pole, 120 L5-30 1 HBL2610SW HBL2611SW
3 Wire 208-240 L6-30 3 HBL2620SW HBL2621SW
120/240 L14-30 3 HBL2710SW HBL2711SW
3 Pole, 240 3Ø L15-30 7.5 HBL2720SW HBL2721SW
HBL2320SW
30 4 Wire 480 3Ø L16-30 15 HBL2730SW HBL2731SW
600 3Ø L17-30 15 HBL2740SW HBL2741SW
120/208 3ØY L21-30 7.5 HBL2810SW HBL2811SW
4 Pole,
277/480 L22-30 7.5 HBL2820SW HBL2821SW
5 Wire
347/600 L23-30 7.5 HBL2830SW HBL2831SW
Note: *HP ratings for the final unit are determined by the HP rating of the switch, limited by the full load current capability
of the receptacle at 80% of rated current, number of phases and line voltage. HP ratings listed above are AC only.

Switched Safety Enclosures (Receptacles Sold Separately**)

Description Ratings Catalog Number
Switched Twist-Lock® enclosure Amperage, voltage, and horsepower ratings will be SETL3
accommodates any NEMA 2 pole, 3 wire determined by the choice of the NEMA 20 or 30A
to 4 pole, 5 wire grounding receptacle. Twist-Lock® receptacle selected.
Switched enclosure for use with 3 pole Amperage, voltage, and horsepower ratings will be SEHBL3 SETL3
4 wire 30A Hubbellock® receptacle. determined by the choice of the 4 wire Hubbellock®
Note: **Please see the full line catalog for a complete selection of Twist-Lock and Hubbellock devices.
® ®

SEHBL3

www.hubbell.com
8
 Circuit-Lock® Pin and Sleeve Mechanical Interlocks
• Mechanically interlocked to prevent mating and breaking under load
• Switch cannot be turned ON unless the plug is properly inserted
and locked
• High visibility red handle can be locked in the OFF position as a
method of compliance with OSHA Lockout/Tagout requirements
• Available in both IEC and UL1686-C1 Insulgrip® styles
• IEC reverse service units available for safely connecting generators
• Fused disconnects accept Class "J" fuses

IP67
SUITABILITY

HBL420MI7W

HBL430MIF7W
Circuit-Lock® Pin and Sleeve Mechanical Interlocks
Amp Poles/Wires Voltage AC Unfused Reverse Service Fused*
120/240V HBL420MI12W — —
3 Pole,
20 3Ø 240V HBL420MI9W — —
4 Wire
3Ø 480V HBL420MI7W — —
120V HBL330MI4W — —
2 Pole,
240V HBL330MI6W — —
3 Wire
480V HBL330MI7W — —
120/240V HBL430MI12W — HBL430MIF12W
30 3 Pole,
3Ø 240V HBL430MI9W HBL430MI9WR HBL430MIF9W
4 Wire
3Ø 480V HBL430MI7W HBL430MI7WR HBL430MIF7W
4 Pole, 3ØY 120/208V HBL530MI9W — —
5 Wire 3ØY 277/480V HBL530MI7W — HBL530MIF7W
32 3 Pole, 4 Wire 380V 50HZ-440V 60Hz HBL432MI3W — —
120V HBL360MI4W — —
2 Pole,
240V HBL360MI6W — —
3 Wire
480V HBL360MI7W — —
120/240V HBL460MI12W HBL460MI12WR HBL460MIF12W
60 3 Pole,
3Ø 240V HBL460MI9W HBL460MI9WR HBL460MIF9W
4 Wire
3Ø 480V HBL460MI7W HBL460MI7WR HBL460MIF7W
4 Pole, 3ØY 120/208V HBL560MI9W — HBL560MIF9W
5 Wire 3ØY 277/480V HBL560MI7W — —
2 Pole, 3 Wire 240V HBL3100MI6W — —
120/240V HBL4100MI12W HBL4100MI12WR —
3 Pole,
100 3Ø 240V HBL4100MI9W HBL4100MI9WR —
4 Wire
3Ø 480V HBL4100MI7W HBL4100MI7WR —
4 Pole, 5 Wire 3ØY 120/208V HBL5100MI9W — —
Note: 20A, 30A, 32A – 1 inch N.P.T. hub supplied; 60A, 100A – 1¼ inch hub supplied.

Insulgrip® Mechanical Interlocks - Style II

Amp Poles/Wires Voltage Unfused Fused*
30 3 Pole, 4 Wire 600V AC/250V DC HBL430MIS2W HBL430MIFS2W
60 3 Pole, 4 Wire 600V AC/250V DC HBL460MIS2W HBL460MIFS2W
Note: 30A – 1 inch N.P.T. hub supplied; 60A – 1¼ inch hub supplied.
*Class “J” fuses not included.

HBL460MIFS2W

www.hubbell.com
9
 Hazardous Location Unfused Disconnect Switches,
Mechanical Interlocks and Plugs
• Compact size provides application flexibility and cost savings
• Fewer cover bolts reduces installation and maintenance time
• UL 98 certified switch
• High visibility handles meet OSHA Lockout/Tagout regulations
• Constructed from copper-free aluminum with a polyester/epoxy
finish to prevent corrosion
• Suitable for use in outdoor or indoor damp, wet and dirty
locations with frequent wash-downs, heavy rain or water spray

Unfused Disconnect Switches

3 Pole 600V AC/230V DC
Amp Description Catalog Number
HBLB7NFD26A
Disconnect switch HBLB7NFD13A
30
Disconnect switch with auxiliary contact HBLB7NFD13AA Class I, Div. 1 & 2, Groups B,C,D
Disconnect switch HBLB7NFD26A Class l, Zones 1 & 2, Groups llB+ H2, llA
60 Class II, Div. 1 & 2, Groups E,F,G
Disconnect switch with auxiliary contact HBLB7NFD26AA HBLB7NFD13A Class III
Disconnect switch HBLB7NFD21A NEMA 3, 4, 4X, 7(B,C,D), 9(E,F,G)
100
Disconnect switch with auxiliary contact HBLB7NFD21AA
Note: 30A bodies have 1” top and bottom drilled and tapped conduit entrances.
60A & 100A bodies have 1-½” top and bottom drilled and tapped conduit entrances.

• UL508 certified switch

• Plug and switch are interlocked for superior safety
• UL1686 C1 listed and fully interchangeable
with other UL1686 C1 devices
• Compact size and footprint for easy placement
• NEMA 4X with receptacle lid turned shut or with plug
locking ring tightened
• Switch features a copper-free aluminum construction
with epoxy finish

Unfused Mechanical Interlocks and Plugs

Amp Poles/Wires Voltage AC Receptacle Plug
3 Pole, 2 Wire 600V AC HBLVSQ3023 HBLVP3385
30
4 Pole, 3 Wire 600V AC HBLVSQ3034 HBLVP3485
3 Pole, 2 Wire 600V AC HBLVSQ6023 HBLVP6385
60
4 Pole, 3 Wire 600V AC HBLVSQ6034 HBLVP6485
Note: HBLVSQ Series 30A models come standard with 1" drilled and tapped conduit
openings top and bottom plus two 1" x ¾" reducers and one ¾" close-up plug for
maximum flexibility. 60A models come with one 1½" opening on top and bottom
and one 1½" close-up plug.

HBLVP3485

HBLVSQ3034

www.hubbell.com
10
600V AC Manual Motor Controllers/Disconnects

600V AC Manual Motor Controllers/Disconnects

HP Rating
120V AC 240V AC 480V AC 600V AC
Amp Poles Toggle-type Wire 1Ø 3Ø 3Ø 3Ø Catalog Number
2 Standard Back/Side 2 5 10 15 HBL7832D
2 Short Back/Side 2 5 10 15 HBL7832DS
30 2 Standard Back/Side 2 5 10 15 HBL7832DX*
3 Standard Back/Side 3 7.5 15 20 HBL7810D
3 Short Back/Side 3 7.5 15 20 HBL7810DS
2 Standard Side 2 5 10 15 HBL7842D
40
3 Standard Side 3 7.5 15 20 HBL7843D
2 Standard Side 2 5 10 15 HBL7852D
50
3 Standard Side 3 7.5 15 25 HBL7853D
2 Standard Back — 10 15 20 HBL7862D
3 Standard Back — 10 25 30 HBL7863D
60 30A, 40A and 50A
2 Standard Front — 10 15 20 HBL7862FWD
3 Standard Front — 10 25 30 HBL7863FWD
2 Standard Back — 10 15 20 HBL7882D
85
3 Standard Back — 10 25 40 HBL7883D
Optional Side Guard (close wall applications & finger safe environments) HBLFG30
Note: *HBL7832DX is a 50 piece bulk pack of the HBL7832D.

Circuit-Lock® NEMA 1 Enclosures with Switch

Ideal for use in industrial environments, i.e. conveyor systems, industrial fans, etc.
HP Rating Catalog
Amp Poles Enclosure Material 120V AC 1Ø 240V AC 3Ø 480V AC 3Ø 600V AC 3Ø Number
2 Thermoplastic/Steel 2 5 10 15 HBL1392D
30
3 Thermoplastic/Steel 3 7.5 15 20 HBL1389D
2 Aluminum 2 5 10 15 HBL1372D
30
3 Aluminum 3 7.5 15 20 HBL1379D HBL1389D HBL1379D

Circuit-Lock® NEMA 3/3R Enclosures with Switch*

Ideal for use on outdoor equipment.
HP Rating Catalog Number
Enclosure 120V AC 240V AC 480V AC 600V AC
Amp Poles Material 1Ø 3Ø 3Ø 3Ø NEMA 3 NEMA 3R
2 Thermoplastic 2 5 10 15 HBL13R22D —
30
3 Thermoplastic 3 7.5 15 20 HBL13R23D —
2 Aluminum 2 5 10 15 HBL13R12D† HBL13R92D
30
3 Aluminum 3 7.5 15 20 HBL13R13D† HBL13R89D
2 Aluminum — 10 15 20 — HBL16R92D
60 HBL13R89D HBL13R23D
3 Aluminum — 10 25 30 — HBL16R93D
Note: *Drill weep-hole to alter from NEMA 3 to NEMA 3R. Equipped with HBLFG30 sidewall insulation barriers.
†

Circuit-Lock® NEMA 4X Enclosures with Rotary Handle

Ideal for use where wash-down is necessary
HP Rating
Amp Poles Enclosure Material 120V AC 1Ø 240V AC 3Ø 480V AC 3Ø 600V AC 3Ø Catalog Number

3 Stainless Steel 3 7.5 15 20 HBL13S33D

30
3 Nonmetallic 3 7.5 15 20 HBL13X33D
3 Stainless Steel — 10 25 30 HBL16S63D
60
3 Nonmetallic — 10 25 30 HBL16X63D
Finger Guard option for 30A switch HBLFG30
NO/NC auxiliary contact, 10A 120/250V AC for 30 and 60 Amp rotary switches HBLAUX HBL16S63D

www.hubbell.com
11
CIRCUIT-LOCK® and MOTORQUICK®
Manual Motor Controllers & Disconnects

Horsepower Ratings Quick Reference Guide for Circuit-Lock® Switched Enclosures

HP
Amp Description Phase Poles 120 240 480 600 Catalog Number
30 TYPE 1 Non-Metallic 3 3 3 7.5 15 20 HBL1389MQR
TYPE 1 Non-Metallic 3 3 3 7.5 15 20 HBL1389MQ5 HBL1379D HBL13R89D
TYPE 1 Non-Metallic 3 3 3 7.5 15 20 HBL1389MQR2
NEMA 1 Aluminum 1 2 2 5 10 15 HBL1372D
NEMA 1 Aluminum 3 3 3 7.5 15 20 HBL1379D
NEMA 1 Non-Metallic 1 2 2 5 10 15 HBL1392D
NEMA 1 Non-Metallic 3 3 3 7.5 15 20 HBL1389D
NEMA 3/3R Non-Metallic 1 2 2 5 10 15 HBL13R22D
NEMA 3/3R Non-Metallic 3 3 3 7.5 15 20 HBL13R23D
NEMA 3R Die Cast Aluminum 1 2 2 5 10 15 HBL13R12D
NEMA 3R Die Cast Aluminum 3 3 3 7.5 15 20 HBL13R13D
NEMA 3R Aluminum 1 2 2 5 10 15 HBL13R92D HBLDS3 HBL16R93D
NEMA 3R Aluminum 3 3 3 7.5 15 20 HBL13R89D
IP69k TYPE 4X Labelless Non-Metallic 3 3 1 7.5 15 15 HBLDS3
IP69k TYPE 4X Labelless Non-Metallic 3 3 1 7.5 15 15 HBLDS3AC
IP69k TYPE 4X Labelless Non-Metallic 3 3 1 7.5 15 15 HBLDS3AC2
IP69k TYPE 4X Labelless Non-Metallic 3 3 1 7.5 15 15 HBLDS3NK
IP69k TYPE 4X Labelless Non-Metallic 3 3 1 7.5 15 15 HBLDS3ACNK
IP69k TYPE 4X Labelless Non-Metallic 3 3 1 5 10 10 HBLDS33ACNK
TYPE 4X Labelless Non-Metallic 3 3 1 7.5 15 15 HBLDS3MQR HBL13S33D FDS30
TYPE 4X Labelless Non-Metallic 3 3 1 7.5 15 15 HBLDS3MQ5
TYPE 4X Labelless Non-Metallic 3 3 1 7.5 15 15 HBLDS3MQR2
IP69k TYPE 4X Stainless Steel 3 3 1 7.5 15 15 HBLDS3SS
IP69k TYPE 4X Stainless Steel 3 3 1 7.5 15 15 HBLDS3SSAC
IP69k TYPE 4X Stainless Steel 3 3 1 7.5 15 15 HBLDS3SSVFD
TYPE 4X Stainless Steel 3 3 1 7.5 15 15 HBLDS3SSMQR
TYPE 4X Stainless Steel 3 3 1 7.5 15 15 HBLDS3SSMQ5
IP69k TYPE 4X, 12 and IP69k Sloped, SS 1 3 1 3 5 15 HBLDS3SSR
IP69k TYPE 4X, 12 and IP69k Sloped, SS 1 3 1 3 5 15 HBLDS3SSR2K
IP69k TYPE 4X, 12 and IP69k Sloped, SS 1 3 1 3 5 15 HBLDS3SSRVFD HBLDS3P HBLDS3J
IP69k TYPE 4X, 12 and IP69k Sloped, SS 1 3 1 3 5 15 HBLDS3SSRAC
IP69k TYPE 4X, 12 and IP69k Sloped, SS 1 3 1 3 5 15 HBLDS3SSRMQR
IP69k TYPE 4X, 12 and IP69k Sloped, SS 1 3 1 3 5 15 HBLDS3SSRMQ5
IP69k TYPE 4X, 12 and IP69k Sloped, SS 1 3 1 3 5 15 HBLDS3SSRMQR2
TYPE 4X Non-Metallic Fused Disconnect 3 3 1 7.5 15 20 FDS30
NEMA 4X Stainless Steel 3 3 3 7.5 15 20 HBL13S33D
NEMA 4X Non-Metallic 3 3 3 7.5 15 20 HBL13X33D
60 NEMA 3R Aluminum 1 2 — 10 15 20 HBL16R92D HBLDS3MQR
NEMA 3R Aluminum 3 3 — 10 25 30 HBL16R93D
IP69k TYPE 4X Non-Metallic 3 3 7.5 30 50 50 HBLDS6
IP69k TYPE 4X Non-Metallic 3 3 7.5 30 50 50 HBLDS6AC HBLDS3MQ5
IP69k TYPE 4X Stainless Steel 3 3 7.5 30 50 50 HBLDS6SS
IP69k TYPE 4X Stainless Steel 3 3 7.5 30 50 50 HBLDS6SSAC
IP69k TYPE 4X, 12 and IP69k Sloped, SS 3 3 7.5 30 50 50 HBLDS6SSR
IP69k TYPE 4X, 12 and IP69k Sloped, SS 3 3 7.5 30 50 50 HBLDS6SSRVFD
IP69k TYPE 4X, 12 and IP69k Sloped, SS 3 3 7.5 30 50 50 HBLDS6SSRAC
TYPE 4X Non-Metallic Fused Disconnect 3 3 3 15 30 40 FDS60
NEMA 4X Stainless Steel 3 3 — 10 25 30 HBL16S63D
NEMA 4X Non-Metallic 3 3 — 10 25 30 HBL16X63D
HBLDS3SS HBLDS3SSR
100 IP69k TYPE 4X Non-Metallic 3 3 7.5 30 50 50 HBLDS10
IP69k TYPE 4X Non-Metallic 3 3 7.5 30 50 50 HBLDS10AC
IP69k TYPE 4X Stainless Steel 3 3 7.5 30 50 50 HBLDS10SS
IP69k TYPE 4X Stainless Steel 3 3 7.5 30 50 50 HBLDS10SSAC
IP69k TYPE 4X, 12 and IP69k Sloped, SS 3 3 7.5 30 50 50 HBLDS10SSR
IP69k TYPE 4X, 12 and IP69k Sloped, SS 3 3 7.5 30 50 50 HBLDS10SSRVFD
IP69k TYPE 4X, 12 and IP69k Sloped, SS 3 3 7.5 30 50 50 HBLDS10SSRAC
200 Type 4X, 12 Non-Metallic 10 75 150 200 HBLDS20
Type 4X, 12 Stainless Steel 10 75 150 200 HBLDS20SS
Note: HP ratings apply to Jog and LED versions. HBLDS20 HBLDS20SS

®
www.hubbell.com/wiringdevice-kellems/en
Wiring Device-Kellems

Hubbell Wiring Device-Kellems • Hubbell Incorporated (Delaware) • 40 Waterview Drive • Shelton, CT 06484 • Phone (800) 288-6000 • FAX (800) 255-1031
Printed in U.S.A. Specifications subject to change without notice. ® Registered trademarks of Hubbell Incorporated. WLBDS003 6/18