Muk PDF
Muk PDF
TEST REPORT
IEC 60950-1
Information technology equipment – Safety –
Part 1: General requirements
TRF No. IEC60950_1F TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Page 3 of 48
Report No.: 085-110044304-000
TRF No. IEC60950_1F TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Page 4 of 48
Report No.: 085-110044304-000
Summary of compliance with National Differences:
List of countries addressed: National Differences and Group Differences as per CB bulletin. See
attachment of National and Group Differences for details
The product fulfils the requirements of EN60950-1:2006 + A11:2009 + A1:2010 + A12:2011 + A2:2013
These are representative labels; the others are identical with them except model name, output rating.
Minimum height of CE mark is 5mm, minimum height of WEEE mark is 7mm.
TRF No. IEC60950_1F TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Page 5 of 48
Report No.: 085-110044304-000
Test item particulars...................................................:
Equipment mobility.................................................: [] movable [] hand-held [] transportable
[] stationary [] for building-in [√] direct plug-in
Connection to the mains........................................: [√] pluggable equipment [√] type A [] type B
[] permanent connection
[] detachable power supply cord
[] non-detachable power supply cord
[] not directly connected to the mains
Operating condition................................................: [√] continuous
[] rated operating / resting time:
Access location ......................................................: [√] operator accessible
[] restricted access location
Over voltage category (OVC) ................................: [] OVC I [√] OVC II [] OVC III [] OVC IV
[] other:
Mains supply tolerance (%) or absolute mains
supply values .........................................................: +10%, -10% (requested by applicant)
Tested for IT power systems .................................: [√] Yes [] No
IT testing, phase-phase voltage (V) ......................: 230V (only for Norway)
Class of equipment ................................................: [] Class I [√] Class II [] Class III
[] Not classified
Considered current rating of protective device as 16A except 13A for United Kingdom
part of the building installation (A) .......................: (20A for Canada and United States)
Pollution degree (PD) .............................................: [] PD 1 [√] PD 2 [] PD 3
IP protection class ..................................................: IP20
Altitude during operation (m) ................................: < 2000 m
Altitude of test laboratory (m) ...............................: < 500
Mass of equipment (kg) .........................................: Approx. 0.07kg
Possible test case verdicts:
- test case does not apply to the test object ........... : N/A
- test object does meet the requirement.................. : P (Pass)
- test object does not meet the requirement ........... : F (Fail)
Testing.......................................................................... :
Date of receipt of test item ........................................ : 2015-07-21
Date (s) of performance of tests ............................... : 2015-07-22 to 2015-08-22
General remarks:
The test results presented in this report relate only to the object tested.
This report shall not be reproduced, except in full, without the written approval of the Issuing testing
laboratory.
"(See Enclosure #)" refers to additional information appended to the report.
"(See appended table)" refers to a table appended to the report.
TRF No. IEC60950_1F TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Page 6 of 48
Report No.: 085-110044304-000
Manufacturer’s Declaration per sub-clause 6.2.5 of IECEE 02:
The application for obtaining a CB Test Certificate
includes more than one factory location and a
declaration from the Manufacturer stating that the
sample(s) submitted for evaluation is (are)
representative of the products from each factory has Yes
been provided ............................................................... : Not applicable
When differences exist; they shall be identified in the General product information section.
Name and address of factory (ies) .......................... : Shenzhen Mass Power Electronic Limited
437#, Hedong Village, Hengkeng Community,
Guanlan Street, Bao’an District, 518110 Shenzhen,
PEOPLE'S REPUBLIC OF CHINA.
General product information:
1. These switch mode power supplies are designed for supply information technology equipment, for
indoor use only and ambient temperature 45°C Max.
2. Models SCFxxxyyyyz1mn (xxx=036-120; yyyy=0005-0100; z=A, C, E, G, I, K, M, O; m=B, W, G, L;
n=A-Z or 0-9);
xxx=036-120 indicates rated output voltage range 3,6-12,0 V d.c.;
yyyy=0005-0100 indicates rated output current range 50-1000 mA;
z=A, C, E, G, I, K, M, O, indicates type of the AC plug,
z=A, sample with United States, Japan or Taiwan plug,
z=C, sample with China plug,
z=E, sample with Europe plug,
z=G, sample with United Kingdom, Hongkong or Singapore plug,
z=I, sample with Australia plug,
z=K, sample with Korean plug,
z=M, sample with Argentina plug,
z=O, sample with India plug.
m=B, W, G, L, indicates the color of enclosure, n=A-Z or 0-9, indicates the customer code.
3. All models are similar except parameter of transformer and some components.
4. These adaptors’s top enclosure is secured to bottom enclosure by ultrasonic welding.
5. These models are in compliance with the requirements of sub clause 2.5 (limited power source).
TRF No. IEC60950_1F TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Page 7 of 48
Report No.: 085-110044304-000
IEC 60950-1
Clause Requirement + Test Result - Remark Verdict
1 GENERAL P
1.5 Components P
1.5.1 General Components which were found P
to affect safety aspects comply
with the requirements of this
standard or within the safety
aspects of the relevant IEC
component standards.
Comply with IEC 60950-1 or relevant component (see appended tables 1.5.1) P
standard
1.5.2 Evaluation and testing of components Components which are certified P
to IEC and /or national
standards are used correctly
within their ratings.
Components not covered by
IEC standards are tested under
the conditions present in the
equipment.
1.5.3 Thermal controls No thermal controls provided. N/A
1.5.4 Transformers Transformer used are suitable P
for their intended application
and comply with the relevant
requirements of the standard
and particularly Annex C.
1.5.5 Interconnecting cables Interconnection o/p cable to P
other device is carrying only
SELV on an energy level below
240 VA.
1.5.6 Capacitors bridging insulation N/A
1.5.7 Resistors bridging insulation N/A
1.5.7.1 Resistors bridging functional, basic or N/A
supplementary insulation
1.5.7.2 Resistors bridging double or reinforced insulation N/A
between a.c. mains and other circuits
1.5.7.3 Resistors bridging double or reinforced insulation N/A
between a.c. mains and antenna or coaxial cable
1.5.8 Components in equipment for IT power systems P
1.5.9 Surge suppressors N/A
1.5.9.1 General N/A
1.5.9.2 Protection of VDRs N/A
1.5.9.3 Bridging of functional insulation by a VDR N/A
1.5.9.4 Bridging of basic insulation by a VDR N/A
TRF No. IEC60950_1F TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Page 8 of 48
Report No.: 085-110044304-000
IEC 60950-1
Clause Requirement + Test Result - Remark Verdict
Other markings and symbols ................................ : Other marks do not give rise to P
misunderstanding
1.7.1.3 Use of graphical symbols P
1.7.2 Safety instructions and marking P
1.7.2.1 General P
1.7.2.2 Disconnect devices N/A
1.7.2.3 Overcurrent protective device Pluggable equipment type A N/A
1.7.2.4 IT power distribution systems Only for Norway P
1.7.2.5 Operator access with a tool No such area N/A
1.7.2.6 Ozone N/A
1.7.3 Short duty cycles Continuous operation N/A
TRF No. IEC60950_1F TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Page 9 of 48
Report No.: 085-110044304-000
IEC 60950-1
Clause Requirement + Test Result - Remark Verdict
1.7.4 Supply voltage adjustment ................................... : Only one supply voltage range N/A
Methods and means of adjustment; reference to N/A
installation instructions ......................................... :
1.7.5 Power outlets on the equipment .......................... : No outlet used N/A
1.7.6 Fuse identification (marking, special fusing Non-replaceable fusible resistor P
characteristics, cross-reference) ............................: “10ohm/1W” marked on PCB
near RF1
1.7.7 Wiring terminals No such terminals N/A
1.7.7.1 Protective earthing and bonding terminals ..............: N/A
1.7.7.2 Terminals for a.c. mains supply conductors N/A
1.7.7.3 Terminals for d.c. mains supply conductors N/A
1.7.8 Controls and indicators No switch used N/A
1.7.8.1 Identification, location and marking .........................: N/A
1.7.8.2 Colours ...................................................................: N/A
1.7.8.3 Symbols according to IEC 60417............................: N/A
1.7.8.4 Markings using figures ..........................................: N/A
1.7.9 Isolation of multiple power sources ........................: Only one power source N/A
1.7.10 Thermostats and other regulating devices .............: N/A
1.7.11 Durability Rubbing test for 15 s with water P
then for 15 s with petroleum
spirit, no curling and legible
after test
1.7.12 Removable parts Rating label stick on enclosure N/A
and no removable part within
equipment
1.7.13 Replaceable batteries ......................................... : No batteries used N/A
Language(s) ........................................................ :
1.7.14 Equipment for restricted access locations ........... : No restricted access lication N/A
TRF No. IEC60950_1F TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Page 10 of 48
Report No.: 085-110044304-000
IEC 60950-1
Clause Requirement + Test Result - Remark Verdict
Test with test probe (Figure 2C) ........................... : No TNV circuit within N/A
equipment
2.1.1.2 Battery compartments N/A
2.1.1.3 Access to ELV wiring N/A
Working voltage (Vpeak or Vrms); minimum
distance through insulation (mm)
2.1.1.4 Access to hazardous voltage circuit wiring N/A
2.1.1.5 Energy hazards ..................................................... : (see appended tables 2.1.1.5) P
2.1.1.6 Manual controls N/A
2.1.1.7 Discharge of capacitors in equipment No X capacitor used N/A
Measured voltage (V); time-constant (s) ............... :
2.1.1.8 Energy hazards – d.c. mains supply Connected to a.c. mains supply N/A
only
a) Capacitor connected to the d.c. mains supply . : N/A
b) Internal battery connected to the d.c. mains N/A
supply :
2.1.1.9 Audio amplifiers .................................................... : No such amplifier N/A
2.1.2 Protection in service access areas N/A
2.1.3 Protection in restricted access locations N/A
TRF No. IEC60950_1F TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Page 11 of 48
Report No.: 085-110044304-000
IEC 60950-1
Clause Requirement + Test Result - Remark Verdict
TRF No. IEC60950_1F TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Page 12 of 48
Report No.: 085-110044304-000
IEC 60950-1
Clause Requirement + Test Result - Remark Verdict
TRF No. IEC60950_1F TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Page 13 of 48
Report No.: 085-110044304-000
IEC 60950-1
Clause Requirement + Test Result - Remark Verdict
TRF No. IEC60950_1F TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Page 14 of 48
Report No.: 085-110044304-000
IEC 60950-1
Clause Requirement + Test Result - Remark Verdict
TRF No. IEC60950_1F TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Page 15 of 48
Report No.: 085-110044304-000
IEC 60950-1
Clause Requirement + Test Result - Remark Verdict
TRF No. IEC60950_1F TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Page 16 of 48
Report No.: 085-110044304-000
IEC 60950-1
Clause Requirement + Test Result - Remark Verdict
TRF No. IEC60950_1F TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Page 17 of 48
Report No.: 085-110044304-000
IEC 60950-1
Clause Requirement + Test Result - Remark Verdict
TRF No. IEC60950_1F TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Page 18 of 48
Report No.: 085-110044304-000
IEC 60950-1
Clause Requirement + Test Result - Remark Verdict
Type ...................................................................... :
2
Rated current (A), cross-sectional area (mm ),
AWG ...................................................................... :
3.2.5.2 DC power supply cords N/A
3.2.6 Cord anchorages and strain relief N/A
Mass of equipment (kg), pull (N) .......................... :
Longitudinal displacement (mm) ........................... :
3.2.7 Protection against mechanical damage N/A
3.2.8 Cord guards N/A
Diameter or minor dimension D (mm); test mass (g)
............................................................................... :
Radius of curvature of cord (mm) .......................... :
3.2.9 Supply wiring space N/A
TRF No. IEC60950_1F TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Page 19 of 48
Report No.: 085-110044304-000
IEC 60950-1
Clause Requirement + Test Result - Remark Verdict
4 PHYSICAL REQUIREMENTS P
4.1 Stability N/A
Angle of 10° N/A
Test force (N) ........................................................ : N/A
TRF No. IEC60950_1F TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Page 20 of 48
Report No.: 085-110044304-000
IEC 60950-1
Clause Requirement + Test Result - Remark Verdict
TRF No. IEC60950_1F TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Page 21 of 48
Report No.: 085-110044304-000
IEC 60950-1
Clause Requirement + Test Result - Remark Verdict
TRF No. IEC60950_1F TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Page 22 of 48
Report No.: 085-110044304-000
IEC 60950-1
Clause Requirement + Test Result - Remark Verdict
TRF No. IEC60950_1F TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Page 23 of 48
Report No.: 085-110044304-000
IEC 60950-1
Clause Requirement + Test Result - Remark Verdict
4.7.3.4 Materials for components and other parts inside PCB rated V-0, bobbin material P
fire enclosures rated V-0, approved by UL
4.7.3.5 Materials for air filter assemblies No such devices N/A
4.7.3.6 Materials used in high-voltage components No such components N/A
TRF No. IEC60950_1F TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Page 24 of 48
Report No.: 085-110044304-000
IEC 60950-1
Clause Requirement + Test Result - Remark Verdict
TRF No. IEC60950_1F TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Page 25 of 48
Report No.: 085-110044304-000
IEC 60950-1
Clause Requirement + Test Result - Remark Verdict
TRF No. IEC60950_1F TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Page 26 of 48
Report No.: 085-110044304-000
IEC 60950-1
Clause Requirement + Test Result - Remark Verdict
TRF No. IEC60950_1F TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Page 27 of 48
Report No.: 085-110044304-000
IEC 60950-1
Clause Requirement + Test Result - Remark Verdict
B ANNEX B, MOTOR TESTS UNDER ABNORMAL CONDITIONS (see 4.7.2.2 and N/A
5.3.2)
B.1 General requirements N/A
Position ................................................................. :
Manufacturer ........................................................ :
Type ...................................................................... :
Rated values ....................................................... :
B.2 Test conditions N/A
B.3 Maximum temperatures (see appended table 5.3) N/A
B.4 Running overload test (see appended table 5.3) N/A
B.5 Locked-rotor overload test N/A
Test duration (days) ............................................. :
Electric strength test: test voltage (V) .................. :
B.6 Running overload test for d.c. motors in N/A
secondary circuits
B.6.1 General N/A
B.6.2 Test procedure N/A
B.6.3 Alternative test procedure N/A
B.6.4 Electric strength test; test voltage (V) .................. : N/A
B.7 Locked-rotor overload test for d.c. motors in N/A
secondary circuits
B.7.1 General N/A
B.7.2 Test procedure N/A
B.7.3 Alternative test procedure N/A
B.7.4 Electric strength test; test voltage (V) ................. : N/A
B.8 Test for motors with capacitors (see appended table 5.3) N/A
B.9 Test for three-phase motors (see appended table 5.3) N/A
B.10 Test for series motors N/A
Operating voltage (V) ........................................... :
TRF No. IEC60950_1F TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Page 28 of 48
Report No.: 085-110044304-000
IEC 60950-1
Clause Requirement + Test Result - Remark Verdict
TRF No. IEC60950_1F TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Page 29 of 48
Report No.: 085-110044304-000
IEC 60950-1
Clause Requirement + Test Result - Remark Verdict
TRF No. IEC60950_1F TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Page 30 of 48
Report No.: 085-110044304-000
IEC 60950-1
Clause Requirement + Test Result - Remark Verdict
N ANNEX N, IMPULSE TEST GENERATORS (see 1.5.7.2, 1.5.7.3, 2.10.3.9, 6.2.2.1, N/A
7.3.2, 7.4.3 and Clause G.5)
N.1 ITU-T impulse test generators N/A
N.2 IEC 60065 impulse test generator N/A
TRF No. IEC60950_1F TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Page 31 of 48
Report No.: 085-110044304-000
IEC 60950-1
Clause Requirement + Test Result - Remark Verdict
TRF No. IEC60950_1F TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Page 32 of 48
Report No.: 085-110044304-000
IEC 60950-1
Clause Requirement + Test Result - Remark Verdict
TRF No. IEC60950_1F TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Page 33 of 48
Report No.: 085-110044304-000
IEC 60950-1
Clause Requirement + Test Result - Remark Verdict
TRF No. IEC60950_1F TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Page 34 of 48
Report No.: 085-110044304-000
IEC 60950-1
Clause Requirement + Test Result - Remark Verdict
TRF No. IEC60950_1F TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Page 35 of 48
Report No.: 085-110044304-000
IEC 60950-1
Clause Requirement + Test Result - Remark Verdict
TRF No. IEC60950_1F TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Page 36 of 48
Report No.: 085-110044304-000
IEC 60950-1
Clause Requirement + Test Result - Remark Verdict
Type............................................................. :
TRF No. IEC60950_1F TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Page 37 of 48
Report No.: 085-110044304-000
IEC 60950-1
Clause Requirement + Test Result - Remark Verdict
TRF No. IEC60950_1F TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Page 38 of 48
Report No.: 085-110044304-000
IEC 60950-1
Clause Requirement + Test Result - Remark Verdict
Fault test performed on voltage limiting Voltage measured (V) in SELV circuits
components (V peak or V d.c.)
D7 short-circuit for model SCF0500100E1BA 0V (unit shut down immediately)
D7 short-circuit for model SCF0810062E1BA 0V (unit shut down immediately)
D7 short-circuit for model SCF1200042E1BA 0V (unit shut down immediately)
supplementary information:
Tested under AC 264V, 50Hz
TRF No. IEC60950_1F TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Page 39 of 48
Report No.: 085-110044304-000
IEC 60950-1
Clause Requirement + Test Result - Remark Verdict
TRF No. IEC60950_1F TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Page 40 of 48
Report No.: 085-110044304-000
IEC 60950-1
Clause Requirement + Test Result - Remark Verdict
TRF No. IEC60950_1F TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Page 41 of 48
Report No.: 085-110044304-000
IEC 60950-1
Clause Requirement + Test Result - Remark Verdict
TRF No. IEC60950_1F TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Page 42 of 48
Report No.: 085-110044304-000
IEC 60950-1
Clause Requirement + Test Result - Remark Verdict
Voltage ........................................................ : --
Capacity....................................................... : --
Tested and Certified by (incl. Ref. No.) ....... : --
Circuit protection diagram: --
TRF No. IEC60950_1F TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Page 43 of 48
Report No.: 085-110044304-000
IEC 60950-1
Clause Requirement + Test Result - Remark Verdict
TRF No. IEC60950_1F TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Page 44 of 48
Report No.: 085-110044304-000
IEC 60950-1
Clause Requirement + Test Result - Remark Verdict
TRF No. IEC60950_1F TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Page 45 of 48
Report No.: 085-110044304-000
IEC 60950-1
Clause Requirement + Test Result - Remark Verdict
5.2 TABLE: Electric strength tests, impulse tests and voltage surge tests P
Test voltage applied between: Voltage shape Test voltage Breakdo
(AC, DC, (V) wn
impulse, surge) Yes / No
Functional:
Between L and N before RF1 (RF1 disconnected) AC 1500 No
Basic:
Two terminals of fuse resistor RF1 ( RF1 open condition) AC 1500 No
Reinforced:
Between live parts and output terminal DC 4242 No
Between live parts and accessible enclosure with foil AC 3000 No
T1 primary and secondary AC 3000 No
T1 secondary and core AC 3000 No
Supplementary information:--
TRF No. IEC60950_1F TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Page 46 of 48
Report No.: 085-110044304-000
IEC 60950-1
Clause Requirement + Test Result - Remark Verdict
U1 pin1-pin5
S-C 264Va.c. 10min RF1
→
0.057 0.037 Component U1 damaged, repeat
three times as the same results, no
hazard.
U1 pin3-pin4
S-C 264Va.c. 10min RF1 →
0.057 0.010 Unit shut down immediately, no
damaged, no hazard.
U1 pin3-pin5 S-C 264Va.c. 1s RF1 -- RF1 open immediately, no hazard.
U1 pin4-pin5 RF1 open immediately, component
S-C 264Va.c. 1s RF1 --
U1 damaged, no hazard.
U1 pin5-pin7 S-C 264Va.c. 1s RF1 -- RF1 open immediately, no hazard.
R8
S-C 264Va.c. 10 min RF1
→
0.057 0.031 Component U1 damaged, repeat
three times as the same results, no
hazard.
R9
S-C 264Va.c. 10 min RF1
→
0.057 0.006 Component U1 damaged, repeat
three times as the same results, no
hazard.
R11 RF1 open immediately, component
S-C 264Va.c. 1s RF1 --
U1 damaged, no hazard.
D7
S-C 264Va.c. 10 min RF1 →
0.057 0.009 Unit shut down immediately, no
damaged, no hazard.
Output “V+” to
S-C 264Va.c. 10 min RF1 0.057→0.010 Unit shut down immediately, no
“V-” damaged, no hazard.
0.057→ Output overload up to 0.71A, then
0.065→ unit shut down,
Output “V+” to
O-L 264Va.c.
3hrs
RF1 0.072→ Max. Temperature of T1 winding:
“V-” 54mins 0.080→ 125.5°C, Max. Temperature of T1
0.010 core: 120.0°C, no damage, no
hazards.
For model: SCF0500100E1BA
Output “V+” to
S-C 264Va.c. 10 min RF1 →
0.061 0.009 Unit shut down immediately, no
“V-” damaged, no hazard.
0.061 → Output overload up to 1.22A, then
0.066 → unit shut down,
Output “V+” to
“V-”
O-L 264Va.c.
4hrs
RF1 0.068 → Max. Temperature of T1 winding:
116.4°C, Max. Temperature of T1
1mins 0.017
core: 111.6°C, no damage, no
hazards.
For model: SCF0810062E1BA
Output “V+” to
S-C 264Va.c. 10 min RF1 →
0.058 0.010 Unit shut down immediately, no
“V-” damaged, no hazard.
0.058 → Output overload up to 0.8A, then unit
0.063 → shut down,
Output “V+” to
“V-”
O-L 264Va.c.
4hrs
RF1 0.070 → Max. Temperature of T1 winding:
127.2°C, Max. Temperature of T1
1mins 0.010
core: 124.6°C, no damaged, no
hazard.
TRF No. IEC60950_1F TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Page 47 of 48
Report No.: 085-110044304-000
IEC 60950-1
Clause Requirement + Test Result - Remark Verdict
Supplementary information:
1. “Sc” means short-circuited test, “Oc” means open-circuited test, “O-L” means overload test; Uo means
output voltage at normal load, Uoc means output voltage without load. (Unit: V d.c.)
2. Thermocouple method was used.
3. Tma is 45°C Max. The above data are corrected at Tma=45°C.
4. Limited temperature for T1 winding: 165°C (Class B).
5. The fuse resistor RF1 operated fault tests were repeated 10 times (all source of fuse resistor were
considered, detailed fuse resistor information see appended table 1.5.1), the test results are same, the fuse
resistor body no explode and no hazards.
6. All tests were repeated in AC 90V/60Hz. Same result generated.
TRF No. IEC60950_1F TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Page 48 of 48
Report No.: 085-110044304-000
IEC 60950-1
Clause Requirement + Test Result - Remark Verdict
2. Schematic:
3. Section Drawing:
4. Winding Specification:
END OF REPORT
TRF No. IEC60950_1F TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Page 1 of 71
Report No.: 085-110044304-000
Attachment No. 1
nd
National and Group Differences for IEC 60950-1 2 Ed. +A1:2009+A2:2013 as per CB
Bulletin
National Differences covered by this report
Country CENELEC National Base standard National standard Tested
Group differ. differ.
(see separate
attachment)
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 2 of 71
Report No.: 085-110044304-000
Attachment No. 1
National Differences covered by this report
Country CENELEC National Base standard National standard Tested
Group differ. differ.
(see separate
attachment)
US United States of America - Yes IEC 60950-1 ed2 + UL 60950-1 Am.1; Am.2 Yes
A1+A2
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 3 of 71
Report No.: 085-110044304-000
Attachment No. 1
General remarks:
The test results presented in this report relate only to the object tested.
This report shall not be reproduced, except in full, without the written approval of the Issuing testing laboratory.
Note: Before placing the products in the different countries, the manufacturer must ensure that:
1. Operating Instructions, Ratings Labels and Warnings Labels written in an Accepted or Official Language of
the county in question.
2. The equipment complies with the National Standards and/or Electrical Codes of the country in question.
3. Mains plugs and internal wirings should be assessed to the national standard.
Possible test case verdicts:
- test case does not apply to the test object .................. : N/A
- test object does meet the requirement ....................... : P (Pass)
- test object does not meet the requirement ................. : F (Fail)
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 4 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
AU Australia AU
APPENDIX ZZ
VARIATIONS TO IEC 60950-1, ED.2.0 (2005)+A1(2009) FOR APPLICATION
IN AUSTRALIA AND NEW ZEALAND
(Normative)
ZZ1 INTRODUCTION
This Appendix sets out variations and additional requirements to cover issues which
have not been addressed by the International Standard. These variations indicate
national variations for purposes of the IECEE CB System and will be published in the
IECEE CB Bulletin.
ZZ2 VARIATIONS
The following variations apply to the source text.
1.2 Insert the following between ‘person, service’ and P
‘range, rated frequency’:
POTENTIAL IGNITION SOURCE….. …..1.2.12
1.2.12.20 Insert a new Clause 1.2.12.201 after Clause P
1 1.2.12.15 as follows:
1.2.12.201 POTENTIAL IGNITION SOURCE
Possible fault which can start a fire if the open-
circuit voltage measured across an interruption or
faulty contact exceeds a value of 50 V (peak) a.c.
or d.c. and the product of the peak value of this
voltage and the measured r.m.s current under
normal operating conditions exceeds 15 VA.
Such a faulty contact or interruption in an
electrical connection includes those which may
occur in CONDUCTIVE PATTERNS on PRINTED
BOARDS.
NOTE 201 An electronic protection circuit may be
used to prevent such a fault from becoming a
POTENTIAL IGNITION SOURCE.
NOTE 202 This definition is from AS/NZS
60065:2003.
1.5.1 1. Add the following to the end of the first P
paragraph: ‘or the relevant Australian/New
Zealand Standard’.
2. In NOTE 1, add the following after the word
‘standard’: ‘or an Australian/New Zealand
Standard’
1.5.2. Add the following to the end of the first and third P
dash items: ‘or the relevant Australian/New
Zealand Standard’.
3.2.5.1 Modify Table 3B as follows: N/A
1. Delete the first four rows and replace with the
following:
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 5 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
AU Australia AU
N/A
Minimum conductor sizes
RATED CURRENT of equipment AWG or kcmil
Nominal
A [cross-sectional area in
cross-sectional area 2
2 mm ]
mm
see Note 2
a
Over 0.2 up to and including 3 0,5 18 [0,8]
2. Delete NOTE 1.
a
3. Delete Footnote and replace with the following:
a
This nominal cross-sectional area is only allowed for Class II appliances if the length of the power
supply cord, measured between the point where the cord, or cord guard, enters the appliance, and
the entry to the plug does not exceed 2 m (0.5 mm2 three-core supply flexible cords are not
permitted; see AS/NZS 3191).
4.1.201 Insert a new Clause 4.1.201 after Clause 4.1 as N/A
follows:
4.1.201 Display devices used for television
purposes
Display devices which may be used for television
purposes, with a mass of 7 kg or more, shall
comply with the requirements for stability and
mechanical hazards, including the additional
stability requirements for television receivers,
specified in AS/NZS 60065.
4.3.6 Delete the third paragraph and replace with the N/A
following:
Equipment with a plug portion, suitable for
insertion into a 10 A 3-pin flat-pin socket-outlet
complying with AS/NZS 3112, shall comply with
the requirements in AS/NZS 3112 for equipment
with integral pins for insertion into socket-outlets.
4.3.13.5 Clause 4.3.13.5 and replace with the following: N/A
1.Add the following after each reference to ‘IEC
60825-1’ : or ‘AS/NZS 60825.1’
2. Add the following after ‘IEC 60825-2’ in line
two of the first paragraph:
‘or AS/NZS 60825.2’
4.7 Add the following new paragraph to the end of the N/A
clause:
‘For alternate tests refer to Clause 4.7.201.’
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 6 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
AU Australia AU
4.7.201 Insert a new Clause 4.7.201 after Clause 4.7.3.6 N/A
as follows:
4.7.201 Resistance to fire – Alternative tests
4.7.201.1 General
Parts of non-metallic material shall be resistant to
ignition and spread of fire.
This requirement does not apply to decorative
trims, knobs and other parts unlikely to be ignited
or to propagate flames originating from inside the
apparatus, or the following:
(a) Components that are contained in an
enclosure having a flammability category
of V-0 according to AS/NZS 60695.11.10
and having openings only for the
connecting wires filling the openings
completely, and for ventilation not
exceeding 1 mm in width regardless of
length.
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 7 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
AU Australia AU
(b) The following parts which would N/A
contribute negligible fuel to a fire:
-small mechanical parts, the mass of
which does not exceed 4 g, such as
mounting parts, gears, cams, belts and
bearings;
-small electrical components, such as
capacitors with a volume not exceeding 1
750 mm3, integrated circuits, transistors
and optocoupler packages, if these
components are mounted on material of
flammability category V-1, or better,
according to AS/NZS 60695.11.10.
NOTE In considering how to minimize propagation
of fire and what ‘small parts’ are, account should
be taken of the cumulative effect of small parts
adjacent to each other for the possible effect of
propagating fire from one part to another.
Compliance shall be checked by the tests of
4.7.201.2, 4.7.201.3, 4.7.201.4 and 4.7.201.5.
For the base material of printed boards,
compliance shall be checked by the test of
4.7.201.5. The tests shall be carried out on parts
of non-metallic material which have been removed
from the apparatus. When the glow-wire test is
carried out, the parts shall be placed in the same
orientation as they would be in normal use. These
tests are not carried out on internal wiring.
4.7.201.2 Testing of non-metallic materials Parts
of non-metallic material shall be subject to the
glow-wire test of AS/NZS 60695.2.11 which shall
be carried out at 550°C. Parts for which the glow-
wire test cannot be carried out, such as those
made of soft or foamy material, shall meet the
requirements specified in ISO 9772 for category
FH-3 material. The glow-wire test shall be not
carried out on parts of material classified at least
FH-3 according to ISO 9772 provided that the
sample tested was not thicker than the relevant
part.
4.7.201.3 Testing of insulating materials.
Parts of insulating material supporting
POTENTIAL IGNITION SOURCES shall be
subject to the glow-wire test of AS/NZS
60695.2.11 which shall be carried out at 750°C.
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 8 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
AU Australia AU
The test shall be also carried out on other parts of N/A
insulating material which are within a distance of
3mm of the connection.
NOTE Contacts in components such as switch
contacts are considered to be connections.
For parts which withstand the glow-wire test but
produce a flame, other parts above the connection
within the envelope of a vertical cylinder having a
diameter of 20 mm and a height of 50 mm shall
be subjected to the needle-flame test. However,
parts shielded by a barrier which meets the
needle-flame test shall not be tested.
The needle-flame test shall be made in
accordance with AS/NZS 60695.11.5 with the
following modifications:
Clause of AS/NZS 60695.11.5 Change N/A
9 Test procedure
9.2 Application of needle-flame Replace the first paragraph with:
The specimen shall be arranged so
that the flame can be applied to a
vertical or horizontal edge as shown
in the examples of figure 1. If
possible the flame shall be applied
at least 10 mm from a corner
Replace the second paragraph with:
The duration of application of the
±
test flame shall be 30 s 1 s.
9.3 Number of test specimens Replace with:
The test shall be made on one
specimen. If the specimen does not
withstand the test, the test may be
repeated on two further specimens,
both of which shall then withstand
the test.
11 Evaluation of test results Replace with:
The duration of burning (tb) shall
not exceed 30 s. However, for
printed circuit boards, it shall not
exceed 15 s.
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 9 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
AU Australia AU
The needle-flame test shall not be carried out on parts of material classified as V-0 or V- N/A
1 according to AS/NZS 60695.11.10, provided that the sample tested was not thicker
than the relevant part.
4.7.201.4 Testing in the event of non-extinguishing material
If parts, other than enclosures, do not withstand the glow wire tests of 4.7.201.3, by
failure to extinguish within 30 s after the removal of the glow-wire tip, the needle-flame
test detailed in 4.7.201.3 shall be made on all parts of non-metallic material which are
within a distance of 50 mm or which are likely to be impinged upon by flame during the
tests of 4.7.201.3. Parts shielded by a separate barrier which meets the needle-flame
test need not be tested.
NOTE 1 - If the enclosure does not withstand the glow-wire test the equipment is
considered to have failed to meet the requirements of Clause 4.7.201 without the need
for consequential testing.
NOTE 2 - If other parts do not withstand the glow-wire test due to ignition of the tissue
paper and if this indicates that burning or glowing particles can fall onto an external
surface underneath the equipment, the equipment is considered to have failed to meet
the requirements of Clause 4.7.201 without the need for consequential testing.
NOTE 3 - Parts likely to be impinged upon by the flame are considered to be those
within the envelope of a vertical cylinder having a radius of 10 mm and a height equal to
the height of the flame, positioned above the point of the material supporting, in contact
with, or in close proximity to, connections.
4.7.201.5 Testing of printed boards
The base material of printed boards shall be subjected to the needle-flame test of
Clause 4.7.201.3. The flame shall be applied to the edge of the board where the heat
sink effect is lowest when the board is positioned as in normal use. The flame shall not
be applied to an edge, consisting of broken perforations, unless the edge is less than 3
mm from a POTENTIAL IGNITION SOURCE.
The test is not carried out if the —
-Printed board does not carry any POTENTIAL IGNITION SOURCE;
-Base material of printed boards, on which the available apparent power at a connection
exceeds 15 VA operating at a voltage exceeding 50 V and equal or less than 400 V
(peak) a.c. or d.c. under normal operating conditions, is of flammability category V-1 or
better according to AS/NZS 60695.11.10, or the printed boards are protected by an
enclosure meeting the flammability category V-0 according to AS/NZS 60695.11.10, or
made of metal, having openings only for connecting wires which fill the openings
completely; or
-Base material of printed boards, on which the available apparatus power at a
connection exceeds 15 VA operating at a voltage exceeding 400 V (peak) a.c. or d.c.
under normal operating conditions, and base material of printed boards supporting spark
gaps which provides protection against overvoltages, is of flammability category V-0
according to AS/NZS 60695.11.10 or the printed boards are contained in a metal
enclosure, having openings only for connecting wires which fill the openings completely.
Compliance shall be determined using the smallest thickness of the material.
NOTE – Available apparent power is the maximum apparent power which can be drawn
from the supplying circuit through a resistive load whose value is chosen to maximise
the apparent power for more than 2 min when the circuit supplied is disconnected.
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 10 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
AU Australia AU
6.2.2 For Australia only, delete the first paragraph and N/A
Note, and replace with the following:
In Australia only, compliance with 6.2.2 shall be
checked by the tests of both 6.2.2.1 and 6.2.2.2.
6.2.2.1 For Australia only, delete the first paragraph N/A
including the Note, and replace with the following:
In Australia only, the electrical separation is
subjected to 10 impulses of alternating polarity,
using the impulse test generator reference 1 of
Table N.1. The Interval between successive
impulses is 60 s and the initial voltage, Uc, is:
for 6.2.1 a):7.0 kV for hand-held telephones and
for headsets and 2.5 kV for other equipment; and
for 6.2.1 b) and 6.2.1 c):1.5 kV.
NOTE 201 – The 7 kV impulse simulates lightning
surges on typical rural and semi-rural network
lines.
NOTE 202 – The value of 2.5 kV for 6.2.1 a) was
chosen to ensure the adequacy of the insulation
concerned and does not necessarily simulate
likely overvoltages.
6.2.2.2 For Australia only, delete the first paragraph N/A
including the Note, and replace with the following:
In Australia only, the a.c. test voltage is:
for 6.2.1 a):3 kV; and
for 6.2.1 b) and 6.2.1 c):1.5 kV.
NOTE 201 – Where there are capacitors across
the insulation under test, it is recommended that
d.c. test voltages are used.
NOTE 202 – The 3 kV and 1.5 kV values have
been determined considering the low frequency
induced voltages from the power supply
distribution system.
7.3 Add the following before the first paragraph: N/A
Equipment providing functions that fall only within
the scope of AS/NZS 60065 and that incorporate
a PSTN interface, are not required to comply with
this Clause where the only ports provided on the
equipment, in addition to a coaxial cable
connection and a PSTN interface, are audio or
Video ports and analogue or data ports not
intended to be used for telecommunications
purposes.
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 11 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
AU Australia AU
Annex P Add the following Normative References: N/A
AS/NZS 3191, Electric flexible cords
AS/NZS 3112, Approval and test specification—
Plugs and socket-outlets
Index 1.Insert the following between ‘asbestos, not to be N/A
used as insulation’ and ‘attitude see orientation’:
AS/NZS 3112………………..4.3.6
AS/NZS 3191………………..3.2.5.1(Table 3B)
AS/NZS 60064………………4.1.201
AS/NZS 60695.2.11…………4.7.201.2, 4.7.201.3
AS/NZS 60695.11.10………..4.7.201.1, 4.7.201.5
AS/NZS 60695.11.5…………4.7.201.3
AS/NZS 60825.1…………….4.3.13.5.1
AS/NZS 60825.2…………….4.3.13.5.1
2. Insert the following between ‘positive
temperature coefficient(PTC) device’ and
‘Powder’:
Potential ignition source…………………1.2.201,
4.7.201.3, 4.7.201.5
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 12 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
CA Canada CA
Canada and the United States of America have adopted a single, bi-national standard,
CAN/CSA C22.2 No. 60950-1/UL60950-1, Second Edition, Amendment 1 which is
based on IEC 60950-1, Second Edition, Amendment 1. This bi-national standard should
be consulted for further details on the national conditions and differences summarized
below.
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 13 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
CA Canada CA
1.7.7 Wiring terminals intended to supply Class 2 N/A
outputs in accordance with CEC Part 1 or NEC
shall be marked with the voltage rating and
“Class 2” or equivalent. Marking shall be located
adjacent to the terminals and shall be visible
during wiring.
2.5 Where a fuse is used to provide Class 2, Limited N/A
Power Source, or TNV current limiting, it shall not
be operator-accessible unless it is not
interchangeable.
2.6.3.3 The first column on Table 2D modified to require, N/A
“Smaller of the RATED CURRENT of the
equipment or the PROTECTIVE CURRENT
RATING of the circuit under consideration.”
2.7.1 Suitable NEC/CEC branch circuit protection rated N/A
at the maximum circuit rating is required for all
standard supply outlets and receptacles (such as
supplied in power distribution units) if the supply
branch circuit protection is not suitable.
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 14 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
CA Canada CA
3.2.1 Power supply cords are required to have N/A
attachment plugs rated not less than 125 percent
of the rated current of the equipment.
3.2.1.2 Equipment connected to a centralized d.c. power N/A
system, and having one pole of the DC mains
input terminal connected to the main protective
earthing terminal in the equipment, is required to
comply with special earthing, wiring, marking and
installation instruction requirements.
3.2.3 Permanent connection of equipment to the mains N/A
supply by a power supply cord is not permitted,
except for certain equipment, such as ATMs.
3.2.5 Power supply cords are required to be no longer N/A
than 4.5 m in length.
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 15 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
CA Canada CA
4.3.12 The maximum quantity of flammable liquid stored N/A
in equipment is required to comply with NFPA 30.
4.3.13.5 Equipment with lasers is required to meet the N/A
Canadian Radiation Emitting Devices Act, REDR
C1370 and/or Code of Federal Regulations 21
CFR 1040, as applicable.
4.7 For computer room applications, automated N/A
information storage systems with combustible
3
media greater than 0.76 m (27 cu ft) are required
to have a provision for connection of either
automatic sprinklers or a gaseous agent
extinguishing system with an extended discharge.
4.7.3.1 For computer room applications, enclosures with N/A
combustible material measuring greater than 0.9
2
m (10 sq ft) or a single dimension greater than
1.8 m (6 ft) are required to have a flame spread
rating of 50 or less. For other applications,
enclosures with the same dimensions require a
flame spread rating of 200 or less.
Annex H Equipment that produces ionizing radiation is N/A
required to comply with the Canadian Radiation
Emitting Devices Act, REDR C1370 and/or Code
of Federal Regulations, 21 CFR 1020, as
applicable.
OTHER DIFFERENCES
The following key national differences are based on requirements other than national regulatory
requirements.
1.5.1 Some components and materials associated with (see appended table 1.5.1) P
the risk of fire, electric shock, or personal injury
are required to have component or material
ratings in accordance with the applicable national
(Canadian and/or U.S.) component or material
standard requirements. These components
include:
attachment plugs, battery packs (rechargeable
type, used with transportable equipment),
cathode ray tubes, circuit breakers,
communication circuit accessories, connectors
(used for current interruption of non-LPS circuits),
cord sets and power supply cords, direct plug-in
equipment, enclosures (outdoor), flexible cords
and cables, fuses (branch circuit), fuseholders,
ground-fault current interrupters, industrial control
equipment, insulating tape, interconnecting
cables, lampholders, limit controls, printed wiring,
protectors for communications circuits,
receptacles, solid state controls, supplementary
protectors, switches (including interlock
switches), thermal cutoffs, thermostats, (multi-
layer) transformer winding wire, transient voltage
surge suppressors, tubing, wire connectors, and
wire and cables.
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 16 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
CA Canada CA
1.6.1.2 A circuit for connection to the DC Mains Supply is N/A
classified as either a SELV Circuit, TNV-2 Circuit
or Hazardous Voltage Circuit depending on the
maximum operating voltage of the supply. This
maximum operating voltage shall include
consideration of the battery charging “float
voltage” associated with the intended supply
system, regardless of the marked power rating of
the equipment.
2.3.1 For TNV-2 and TNV-3 circuits with other than N/A
ringing signals and with voltages exceeding 42.4
Vpeak or 60 Vd.c., the maximum acceptable
current through a 2000 ohm resistor (or greater)
connected across the voltage source with other
loads disconnected is 7.1 mA peak or 30 mA d.c.
under normal operating conditions.
2.3.2.1 In the event of a single fault between TNV and N/A
SELV circuits, the limits of 2.2.3 apply to SELV
Circuits and accessible conductive parts.
2.6.3.4 Protective bonding conductors of non-standard N/A
protective bonding constructions (e.g., printed
circuit traces) may be subjected to the additional
limited short circuit test conditions specified.
4.2.8.1 Enclosures around CRTs with a face diameter of N/A
160 mm or more are required to reduce the risk
of injury due to the implosion of the CRT.
4.3.2 Equipment with handles is required to comply N/A
with special loading tests.
5.1.8.3 Equipment intended to receive N/A
telecommunication ringing signals is required to
comply with a special touch current measurement
tests.
5.3.7 Internal (e.g., card cage) SELV circuit connectors P
and printed wiring board connectors that are
accessible to the operator and that deliver power
are to be overloaded.
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 17 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
CA Canada CA
Annex Equipment connected to a telecommunication N/A
NAD and cable distribution networks and supplied with
an earphone intended to be held against, or in the
ear is required to comply with special acoustic
pressure requirements.
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 18 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
CN China CN
1.1.2 GB 4943.1-2011 applies to equipment for use at Should be evaluated when imported N/A
altitudes not exceeding 5000m above sea level, to relevant national
primarily in regions with moderate or tropical
climates.
Amend the third dashed paragraph of 1.1.2 as:
——equipment intended to be used in vehicles, on
board ships or aircraft, at altitudes greater
than 5000m;
1.4.5 After the third paragraph, add a paragraph: P
If the equipment is intended for direct connection
to an AC mains supply, the tolerances on RATED
VOLTAGE shall be taken as +10%,-10% unless a
wider tolerance is declared by the manufacturer.
The first dash paragraph "-the RATED VOLTAGE
is 230V single -phase or 400V three-phase, in
which case the tolerance shall be taken as +10%
and -10%" of IEC 60950-1:2005 is deleted in GB
4943.1-2011
1.4.12.1 Tma in clause 1.4.12.1 amended as: Tma: is the P
maximum ambient temperature permitted by the
manufacturer's specification, or 35 °C, whichever
is greater.
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 19 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
CN China CN
1.7.2.1 Add requirements of warning for equipment Should be evaluated when imported N/A
intended to be used at altitudes not exceeding to relevant national
2000m or at non-tropical climate regions:
For equipment intended to be used at altitude not
exceeding 2000m, a warning label containing the
following or a similar appropriate wording, or a
symbol as in annex DD shall fixed to the
equipment at readily visible place.
"Only used at altitude not exceeding 2000m."
≤2000m
For equipment intended to be used in not-tropical
climate regions, a warning label containing the
following or a similar appropriate wording, or a
symbol as in annex DD shall fixed to the
equipment at readily visible place.
"Only used in not-tropical climate regions."
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 20 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
CN China CN
2.9.2 First section of Clause 2.9.2 amended as two Should be evaluated when imported P
sections: to relevant national
Where required by 2.9.1, 2.10.8.3, 2.10.10 or
2.10.11, humidity conditioning is conducted for
120 h in a cabinet or room containing air with
ambient temperature 40±2℃ and a relative
humidity of (93±3)%. During this conditioning the
component or subassembly is not energized.
For equipment not to be operated at tropical
climatic conditions, Where required by 2.9.1,
2.10.8.3, 2.10.10 or 2.10.11, humidity conditioning
is conducted for 48 h in a cabinet or room
containing air with a relative humidity of (93±3) %.
The temperature of the air, at all places where
samples can be located, is maintained within 2 °C
of any convenient value between 20 °C and 30 °C
such that condensation does not occur.
Due to pretreatment of equipment operated at
high altitude area is humidity conditioning
withstand hot shock, specific requirements are to
be considered.
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 21 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
CN China CN
2.10.3.4 Add a new section above Table 2K and in Clause N/A
2.10.3.4:
Minimum CLEARANCES determined by above
rules apply for equipment to be operated up to
2000m above sea level. For equipment to be
operated at 2000 m - 5000m above sea level, the
minimum CLEARANCE shall be multiplied by the
factor 1.48 corresponding altitude of 5000m given
(
in Table A.2 of GB/T16935.1 IEC 60664-1 . )
For equipment to be operated at more than 5000
m above sea level, the minimum CLEARANCE
shall be multiplied by the factor given in Table A.2
of GB/T16935.1.
3.2.1.1 Add a paragraph before the last paragraph: N/A
Plugs connected to AC mains supply shall comply
with GB 1002 or GB 1003 or GB/T 11918 as
applicable.
4.2.8 Clause 4.2.8 cathode ray tubes quoted Clause 18 N/A
of GB8898-2011.
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 22 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
CN China CN
Annex Added annex DD: Instructions for the new safety N/A
DD warning labels.
(normativ
e) DD.1 Altitude warning label
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 23 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
CN China CN
Quoting The principles of quoting and referring to other standards in Annex P and reference N/A
standards documents of IEC 60950-1 are as follows:
and If the date of the reference document is given, only that edition applies, excluding any
reference subsequent corrigenda and amendments. However, parties to agreements based on this
document part are encouraged to investigate the possibility of applying the most recent editions of
s the reference documents. For undated references, the latest edition of the referenced
document applies, including any corrigenda and amendments.
For the usage of international standards in Chinese national standards and industry
standards is various, in the aim of achieving easy operation and based on the
requirements of GB/T 1.1 and GB/T 20000.2, when quoting an entire international
standard in the normative quoting files and reference documents of Annex P of this part,
the principles of quotation are as follows:
- If there is no national standard or industry standard corresponding to the international
standard, then the international standard is quoted;
- If there is national standard or industry standard corresponding to the international
standard, then either the national or industry standard is quoted;
- If the date of the national standard or industry standard is not given, the latest edition of
the standard applies;
- The national standard or industry standard number, corresponding international
standard number and the consistency level code should be identified in parentheses
behind the listed national standard or industry standard.
When quoting several chapters or clauses of the international standard, the principles of
quotation are as follows:
- If there is no national standard or industry standard corresponding to the international
standard, then the international standard is quoted;
- If there is national standard or industry standard corresponding to the international
standard, then either the national or industry standard is quoted.
Meanwhile, in order to retain the relevant information on international standards,
informative annex CC is increased, which gives the table about the comparison of the
normative quoting files and reference documents in IEC 60950-1: 2005 and GB 4943.1-
2011.
DE Germany DE
1.5 The moulded plug of plug-in power supplies will P
be considered as component and will be
generally evaluated in Germany according to DIN
VDE 0620-1:2010 respectively DIN VDE 0620-
1:2013 and DIN VDE 0620-2-1:2013.
After the test according to DIN VDE 0620-2-
1:2013, sub-clause 24.2, the plug be shall still
pass the test according to DIN VDE 0620-
101:1992 clause 7, figure 2 “Gauge for
interchangeability”.
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 24 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
DE Germany DE
Annex According to GPSG, section 2, clause 4: P
ZC, cl. If certain rules on the use, supplementation or
1.7.2.1 maintenance of an item of technical work
equipment or ready-to-use commodity must be
observed in order to guarantee safety and health,
instructions for use in German must be supplied
when it is brought into circulation.
DK Denmark DK
1.2.4.1 In Denmark, certain types of Class I appliances N/A
(see 3.2.1.1) may be provided with a plug not
establishing earthing conditions when inserted
into Danish socket-outlets.
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 25 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
ES Spain ES
3.2.1.1 In Spain, supply cords of single-phase equipment N/A
having a rated current not exceeding 10 A shall
be provided with a plug according to UNE
20315:1994.
Supply cords of single-phase equipment having a
rated current not exceeding 2,5 A shall be
provided with a plug according to UNE-EN
50075:1993.
CLASS I EQUIPMENT provided with socket-
outlets with earth contacts or which are intended
to be used in locations where protection against
indirect contact is required according to the wiring
rules, shall be provided with a plug in accordance
with standard UNE 20315:1994.
If poly-phase equipment is provided with a supply
cord with a plug, this plug shall be in accordance
with UNE-EN 60309-2.
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 26 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
FI Finland FI
1.5.7.1 Resistors bridging BASIC INSULATION in N/A
CLASS I PLUGGABLE EQUIPMENT TYPE A
must comply with the requirements in 1.5.7.2. In
addition when a single resistor is used, the
resistor must withstand the resistor test in 1.5.7.2.
1.5.9.4 The third dashed sentence is applicable only to N/A
equipment as defined in 6.1.2.2 of this annex.
1.7.2.1 CLASS I PLUGGABLE EQUIPMENT TYPE A N/A
intended for connection to other equipment or a
network shall, if safety relies on connection to
protective earth or if surge suppressors are
connected between the network terminals and
accessible parts, have a marking stating that the
equipment must be connected to an earthed
mains socket-outlet.
The marking text shall be as follows:
"Laite on liitettävä suojakoskettimilla varustettuun
pistorasiaan"
2.3.2 There are additional requirements for the N/A
insulation. See 6.1.2.1 and 6.1.2.2 of this
annex.
2.10.5.1 There are additional requirements for the N/A
3 insulation. See 6.1.2.1 and 6.1.2.2 of this
annex.
5.1.7.1 TOUCH CURRENT measurement results N/A
exceeding 3,5 mA r.m.s. are permitted only for
the following equipment:
• STATIONARY PLUGGABLE EQUIPMENT
TYPE A that
o is intended to be used in a RESTRICTED
ACCESS LOCATION where equipotential
bonding has been applied, for example, in
telecommunication centre; and
o has provision for a permanently
connected PROTECTIVE EARTHING
CONDUCTOR; and
o is provided with instructions for the
installation of that conductor by a
SERVICE PERSON;
• STATIONARY PLUGGABLE EQUIPMENT
TYPE B;
• STATIONARY PERMANENTLY
CONNECTED EQUIPMENT.
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 27 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
FI Finland FI
6.1.2.1 Add the following text between the first and N/A
second paragraph of the compliance clause:
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 28 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
FI Finland FI
6.1.2.2 The exclusions are applicable for N/A
PERMANENTLY CONNECTED EQUIPMENT,
PLUGGABLE EQUIPMENT TYPE B and
equipment intended to be used in a
RESTRICTED ACCESS LOCATION where
equipotential bonding has been applied, e.g. in a
telecommunication centre, and which has
provision for a permanently connected
PROTECTIVE EARTHING CONDUCTOR and is
provided with instructions for the installation of
that conductor by a SERVICE PERSON.
7.2 For requirements see 6.1.2.1 and 6.1.2.2 of this N/A
annex. The term TELECOMMUNICATION
NETWORK in 6.1.2 being replaced by the term
CABLE DISTRIBUTION SYSTEM.
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 29 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
GB United Kingdom GB
2.6.3.3 In the United Kingdom, the current rating of the N/A
circuit shall be taken as 13 A, not 16 A.
2.7.1 In the United Kingdom, to protect against P
excessive currents and short-circuits in the
PRIMARY CIRCUIT of DIRECT PLUG-IN
EQUIPMENT, tests according to 5.3 shall be
conducted, using an external protective device
rated 30 A or 32 A. If these tests fail, suitable
protective devices shall be included as integral
parts of the DIRECT PLUG-IN EQUIPMENT, so
that the requirements of 5.3 are met.
3.2.1.1 In the United Kingdom, apparatus which is fitted N/A
with a flexible cable or cord and is designed to be
connected to a mains socket conforming to BS
1363 by means of that flexible cable or cord and
plug, shall be fitted with a ‘standard plug’ in
accordance with Statutory Instrument 1768:1994
- The Plugs and Sockets etc. (Safety)
Regulations 1994, unless exempted by those
regulations.
NOTE ‘Standard plug’ is defined in SI 1768:1994
and essentially means an approved plug
conforming to BS 1363 or an approved
conversion plug.
3.2.5.1 In the United Kingdom, a power supply cord with N/A
2
conductor of 1,25 mm is allowed for equipment
with a rated current over 10 A and up to and
including 13 A.
3.3.4 In the United Kingdom, the range of conductor N/A
sizes of flexible cords to be accepted by terminals
for equipment with a RATED CURRENT of over
10 A up to and including 13 A is:
2 2
• 1,25 mm to 1,5 mm nominal cross-sectional
area.
4.3.6 In the United Kingdom, the torque test is P
performed using a socket outlet complying with
BS 1363 part 1:1995, including Amendment 1:
1997 and Amendment 2:2003 and the plug part of
DIRECT PLUG-IN EQUIPMENT shall be
assessed to BS 1363: Part 1, 12.1, 12.2, 12.3,
12.9, 12.11, 12.12, 12.13, 12.16 and 12.17,
except that the test of 12.17 is performed at not
less than 125 °C. Where the metal earth pin is
replaced by an Insulated Shutter Opening Device
(ISOD), the requirements of clauses 22.2 and 23
also apply.
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 30 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
IE Ireland IE
3.2.1.1 In Ireland, apparatus which is fitted with a flexible N/A
cable or cord and is designed to be connected to
a mains socket conforming to I.S. 411 by means
of that flexible cable or cord and plug, shall be
fitted with a 13 A plug in accordance with
Statutory Instrument 525:1997 National
Standards Authority of Ireland (section 28) (13 A
Plugs and Conversion Adaptors for Domestic
Use) Regulations 1997.
4.3.6 In Ireland, DIRECT PLUG-IN EQUIPMENT is N/A
known as plug similar devices. Such devices shall
comply with Statutory Instrument 526:1997 -
National Standards Authority of Ireland (Section
28) (Electrical plugs, plug similar devices and
sockets for domestic use) Regulations, 1997.
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 31 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
IL Israel IL
1.6.1 Note: In Israel, the clause is subject to Electricity N/A
Law, 1954, its regulations and updates.
1.7.201 Marking in the Hebrew language N/A
The marking in the Hebrew language shall be in
accordance with the Consumer Protection Order
(Marking of goods), 1983.
In addition to the marking required by clause
1.7.1, the following shall be marked in Hebrew
language.
1. Name of the apparatus and its commercial
designation;
2. Manufacturer's name and address; if the
equipment is imported, the importer's name and
address;
3. Manufacturer's registered trademark, if any;
4. Name of the model and serial number, if any;
5. Country of manufacture.
The details shall be marked on the apparatus or
on its packaging, or on a label well attached to
the apparatus or on the packaging, by bonding or
sewing, such that the label cannot be easily
removed.
1.7.2.1 All the instructions and warnings related to safety N/A
shall also be written in the Hebrew language.
1.201 Power consumption in standby mode Shall be considered during national N/A
The equipment shall comply with the approved
requirements of the Energy Sources Regulations
(Maximum electrical power in standby mode for
domestic and office electrical appliances), 20011,
with a permitted deviation of up to 10%
2.9.4 Separation from hazardous voltages N/A
-The following shall be added at the beginning of
the clause:
According to the Electricity Law, 1954, and the
Electricity Regulations (Earthing and means of
protection against electricity of voltages up to
1000V) , 1991, in Israel, seven means of
protection from electrocution are permitted, as
follows:
1) Network system earthing - (TN-C-S, TN –S);
2) Network system earthing - (TT);
3) Network Insulation Terre – (IT);
4) Isolated transformer;
5) Safety extra low voltage;
6) Residual current circuit breaker;
7) Reinforced insulation; Double insulation.
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 32 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
IL Israel IL
2.201 Prevention of electromagnetic interference N/A
The device shall meet the requirements in the
relevant part of the Israeli Standard series, SI
961.
If the device contains components for the
prevention of electromagnetic interference, the
devices shall not lower the safety level of the
device, as required by this standard.
3.2.1.1 Note: In Israel, the feed plug shall comply with N/A
thee requirements of Israel Standard SI 32
Part1.1.
3.2.1.2 Note: As of the date of publication of this N/A
standard, there is no Israel Standard for
connection accessories to d.c.
Annex P Normative references P
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 33 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
IL Israel IL
P
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 34 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
IL Israel IL
P
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 35 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
IL Israel IL
P
The referenced
The substituted Israel
International Comments
Standard
Standard
IEC 60947-1: 2004 SI 60947 Part 1 -Low- The Israel Standard, excluding
voltage switchgear and national modifications and
controlgear: General rules additions noted, is identical to the
International Electrotechnical
Commission Standard, IEC
60947-1: Edition 5.0: 2007-06.
IEC 61058-1: 2000 SI 61058 Part 1 - The Israel Standard, excluding
Switches for appliances: national modifications and
General requirements additions noted, is identical to the
International Electrotechnical
Commission Standard, IEC
61058-1: Edition 3.1: 2001.
ISO 3864 SI 3864 Part 1(a) - The Israel Standard, excluding
Graphical symbols national modifications and
(all parts)(b)
additions noted, is identical to the
International Organization for
Standardization Standard, ISO
3864-1: First edition 2002-05-15.
Notes:
(a) This Standard is being revised.
(b) In the International Standard series, there are parts not yet adopted as Israeli
Standards. This table notes the relevant Israeli Standards, and in the Comments
column, the corresponding parts of the International Standard series.
(c) Not relevant to the translation.
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 36 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
J 60950-1(H26)
(Deviations from IEC 60950-1:2005, second edition)
Special National conditions, National deviation and other information according to MITI Ordinance No. 85.
Japanese unique deviations in J60950-1(H26) (=JIS C 6950-1:2012)
1.2.4.1 Replace the existing NOTE as NOTE 1, and Added. N/A
add NOTE 2 as following:
NOTE 2: Even if the equipment is designed as
CLASS I EQUIPMENT, if a 2-pin plug adaptor
with a protective earthing lead wire (adaptor
which converts a plug for CLASS I EQUIPMENT
to a 2-pin plug with no earthing contact) or a
cord set having a 2-pin plug with a protective
earthing lead wire is packed as accessory
together with the equipment or if use of those is
recommended to the users, the equipment is
considered as CLASS 0I EQUIPMENT.
1.2.4.3A Add 1.2.4.3A as following: Added. N/A
1.2.4.3A
CLASS 0I EQUIPMENT
Equipment having a mains plug without earthing
contact, which protection against electric shock
is achieved by:
- using BASIC INSULATION; and
- for the measures to connect conductive
part(s) regarded as part at HAZARDIUS
VOLTAGE in the event of fault of BASIC
INSULATION to PROTECTIVE EARTHING
CONDUCTOR, equipping any one of the
following:
a) mains plug with a protective earthing lead
wire, this includeds the following cases:
- where a 2-pin plug adaptor with a
protective earthing lead wire is packed as
accessory together with the equipment; or
- where use of it is recommended.
b) independent protective earthing terminal
(see 2.6.5.8A) if the equipment uses a
power supply cord of two conductors
(exclude earthing conductor)
NOTE - CLASS 0I EQUIPMENT may have a
part constructed with DOUBLE INSUILATION or
REINFORCED INSULATION.
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 37 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
J 60950-1(H26)
(Deviations from IEC 60950-1:2005, second edition)
Special National conditions, National deviation and other information according to MITI Ordinance No. 85.
Japanese unique deviations in J60950-1(H26) (=JIS C 6950-1:2012)
1.3.2 Add the following NOTEs after first paragraph: Added. N/A
NOTE 1 TRANSPORTABLE or similar
equipment that are relocated frequently for
intended usage it is recommended not to design
as CLASS I or CLASS 0I EQUIPMENT unless it
is intended to be installed by a SERVICE
PERSON or installation personnel.
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 38 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
J 60950-1(H26)
(Deviations from IEC 60950-1:2005, second edition)
Special National conditions, National deviation and other information according to MITI Ordinance No. 85.
Japanese unique deviations in J60950-1(H26) (=JIS C 6950-1:2012)
1.5.2 Replace first sentence in the first dashed Added. P
paragraph with the following:
- a component that has been demonstrated
to comply with a JIS component standard
harmonized with the relevant IEC
component standard, or where such JIS
component standard is not available, a
component that has been demonstrated to
comply with the relevant IEC component
standard shall be checked for correct
application and use in accordance with its
rating.
Replace existing NOTE to NOTE 1 without
modification of the sentence in the second
dashed paragraph.
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 39 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
J 60950-1(H26)
(Deviations from IEC 60950-1:2005, second edition)
Special National conditions, National deviation and other information according to MITI Ordinance No. 85.
Japanese unique deviations in J60950-1(H26) (=JIS C 6950-1:2012)
1.7.1 Replace the existing dashed items for Replaced. P
manufacturer’s name etc. and for model
identification etc. with the following respectively:
- manufacturer’s (or responsible business
operator’s) name or trade-mark or
identification mark;
- manufacturer’s (or responsible business
operator’s) model identification or type
reference;
In the last paragraph, replace “ISO 7000 or IEC
60417” with “JIS S 0101, ISO 7000 or IEC
60417”.
1.7.2.1 Add the following: Added. P
Instructions and the marking(s) on equipment, Instruction in Japanese provided.
which related to safety, shall be made in
Japanese.
1.7.5 Replace IEC 60083 with JIS C 8303 in the Replaced. N/A
second paragraph.
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 40 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
J 60950-1(H26)
(Deviations from IEC 60950-1:2005, second edition)
Special National conditions, National deviation and other information according to MITI Ordinance No. 85.
Japanese unique deviations in J60950-1(H26) (=JIS C 6950-1:2012)
1.7.5A Add the following new clause after 1.7.5 Added. N/A
1.7.5.A Power supply cord set
If an appliance inlet with a rated current of 10 A,
which is of STANDARD SHEET C14 specified in
JIS C 8283-1, is used for equipment with a rated
voltage of 125 V or less and with a rated current
of exceeding 10 A, the operating instructions
shall provide the following or equivalent
instruction:
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 41 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
J 60950-1(H26)
(Deviations from IEC 60950-1:2005, second edition)
Special National conditions, National deviation and other information according to MITI Ordinance No. 85.
Japanese unique deviations in J60950-1(H26) (=JIS C 6950-1:2012)
1.7.14B Add the following new clause after 1.7.14 Added. N/A
1.7.14B Protective earth wire used for CLASS 0I
EQUIPMENT
For CLASS 0I EQUIPMENT equipped with a
separate protective earthing terminal as main
protective earthing terminal, if a protective earth
wire is not provided by packing together with the
equipment, the operating instructions shall
provide information on the applicable protective
earth wire. (See 2.6.3.2.)
2.1.1.1 In b) of the fifth paragraph, replace “IEC 60083, Replaced. P
IEC 60309, IEC 60320, IEC 60906-1 or IEC
60906-2” with “JIS C 8303, (the Ministerial
Ordinance establishing Technical Requirements
for Electrical Appliances and Materials, MEIT
Ordinance No. 85, Clause 1 (METI Ordinance
No. 34 of 2013), JIS C 8285, the IEC 60309
series of standards, the JIS C 8283 series of
standards, the IEC 60320 series of standards”.
2.6.3.2 Add the following: Added. N/A
If the conductor of protective earthing lead wire
or the protective earth wire of CLASS 0I
EQUIPMENT is of single-core, it shall be one of
the following:
- annealed copper wire of 1,6 mm in
diameter, or metallic wire having the same or
more strength and diameter and being not easily
corrosive; or
- single-core cord or single-core cabtyre
cable (sheathed flexible cable), which have a
2
cross-sectional area of at least 1,25 mm .
2.6.3.5 Add the following: Added. N/A
However, this requirement does not apply to the
inside conductor of power supply cord (or power
supply cord set), which has been molded
together with a plug and a connector and has
been sheathed.
2.6.4.2 Add the following: Added. N/A
For CLASS 0I EQUIPMENT equipped with a
separate protective earthing terminal, the
protective earthing terminal may be used as the
main protective earthing terminal.
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 42 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
J 60950-1(H26)
(Deviations from IEC 60950-1:2005, second edition)
Special National conditions, National deviation and other information according to MITI Ordinance No. 85.
Japanese unique deviations in J60950-1(H26) (=JIS C 6950-1:2012)
2.6.5.4 Replace 1st sentence with the following. Added. N/A
“Protective earthing conductors” with “Protective
earthing conductors of CLASS I EQUIPMENT”.
2.6.5.6 Replace “protective earthing terminals” with Added. N/A
“protective earthing and protective bonding
terminals”.
2.6.5.8A Add the following new clause. after 2.6.5.8A Added. N/A
2.6.5.8A Earthing of CLASS 0I EQUIPMENT
Plugs with a lead wire for earthing shall not be
used for equipment having a rated voltage
exceeding 150V.
For plugs with a lead wire for earthing, the lead
wire shall not be earthed by a clip.
CLASS 0I EQUIPMENT shall be provided with
an earthing terminal or lead wire for earthing in
the external location where easily visible.
2.9.3 Deleted the following mark of Figure 2H: N/A
Table 2H
B13 e) and S2 d)
2.9.3 Addition of marking for table 2H: N/A
Figure 2H
B8, B9, B12, B13, S1
2.10.3.1 In the third paragraph, replace IEC 60664-1 with Replaced. P
JIS C 60664-1.
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 43 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
J 60950-1(H26)
(Deviations from IEC 60950-1:2005, second edition)
Special National conditions, National deviation and other information according to MITI Ordinance No. 85.
Japanese unique deviations in J60950-1(H26) (=JIS C 6950-1:2012)
2.10.3.2 In the bottom column of Table 2J, add the Added. P
following:
In Japan, the MAINS TRANSIENT VOLTAGE
value against the nominal AC MAINS SUPPLY
voltage of 100 V is decided by applying the
columns for the AC MAINS SUPPLY voltage of
150 V.
2.10.3.3 In Table 2L, add the following into the column Added. P
specifying the additional CLEARANCES and at
the end:
For intermediate voltage values between the
PEAK WORKING VOLTAGE values given in this
table, linear interpolation is permitted between
the nearest two points, the calculated additional
minimum CLEARANCE being rounded up to the
next higher 0,1 mm increment.
2.10.4.3 Replace the 6th paragraph with the following: Replaced. P
The above minimum CLEEPAGE DISTANCES
for connectors do not apply to:
- connectors that comply with JIS C 8285,
the IEC 60309 series of standards, the JIS C
8283 series of standards, the IEC 60320 series
of standards or JIS C 8303; and
- connectors that comply with the
Ministerial Ordinance establishing Technical
Requirements for Electrical Appliances and
Materials MEIT Ordinance No. 85, Clause 1
(METI Ordinance No. 34 of 2013), and comply
with the dimensions specified in the JIS C 8283
series of standards, JIS C8303 or IEC 60309-2;
see also 1.5.2.
1
2.10.9 Replace clause which as test method of T from Replaced. N/A
1.4.5 to 1.4.12.
3.2.1.1 Add the following: Added. N/A
When equipment with an appliance inlet
connects to AC mains supply, see clause 1.7.5A
for the relevant mark of power supply cord set.
3.2.3 Add the following after Table 3A: Added. N/A
Table 3A applies when cables complying JIS C
3662 or JIS C 3663 are used. In case of other
cables, cable entries shall be so designed that a
conduit suitable for the cable used can be fitted.
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 44 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
J 60950-1(H26)
(Deviations from IEC 60950-1:2005, second edition)
Special National conditions, National deviation and other information according to MITI Ordinance No. 85.
Japanese unique deviations in J60950-1(H26) (=JIS C 6950-1:2012)
3.2.4 Add the following: Added. N/A
The equipment shall have a structure of which
the soldered sections of the terminals of
appliance inlet are not subjected to mechanical
stress during the insertion or removal of the
connector, except the case fixing the appliance
inlet itself mechanically but not only by
soldering.
3.2.5.1 At the end of the first dashed item, replace “; Added. N/A
and” with “, or be a sheathed cord complying
with Appendix 1 specified in the Interpretation
for the Ministerial Ordinance establishing
Technical Requirements for Electrical
Appliances and Materials MEIT Ordinance No.
85, Clause 1 (METI Ordinance No. 34 of 2013) ;
and”.
In the second dashed item, replace “insulated:” Added. N/A
with “insulated, be a cord of the following or be a
sheathed cord complying with Appendix 1
specified in the Interpretation for the Ministerial
Ordinance establishing Technical Requirements
for Electrical Appliances and Materials MEIT
Ordinance No. 85, Clause 1 (METI Ordinance
No. 34 of 2013), :”
In the third dashed item, add the following: Added. N/A
However, the coating of the protective earth
conductor inside covered with sheath (cord set)
power cord integrally formed with the connector
and the plug need not be a combination of
green and yellow. In addition, the power cord of
CLASS OI EQUIPMENT having a protective
earth conductor separately, it is not necessary to
provide a protective earth conductor.
Replace the existing fourth dashed item with the Added. N/A
following:
- if those complying with JIS C 3662-5 or JIS
C 3663-4, have conductors with cross-
sectional areas not less than those specified
in Table 3B, and if others, comply with the
relevant wiring rules.
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 45 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
J 60950-1(H26)
(Deviations from IEC 60950-1:2005, second edition)
Special National conditions, National deviation and other information according to MITI Ordinance No. 85.
Japanese unique deviations in J60950-1(H26) (=JIS C 6950-1:2012)
3.3.4 Add the following note to Table 3D: Added. N/A
For cables other than those complying with JIS
C 3662 or JIS C 3663, terminals shall be
suitable for the size of the intended cables.
3.3.7 Add the following after the first sentence: Added. N/A
This requirement is not applicable to the
external earting terminal of CLASS 0I
EQUIPMENT.
4.3.4 Add the following after the first sentence: Added. N/A
This requirement also applies to those
connections in CLASS 0I EQUIPMENT, where
CLEARANCE or CREEPAGE DISTANCES of
BASIC INSULATION would be reduced to less
than the values specified in 2.10.
4.3.5 In the paragraph, replace “IEC 60083 or IEC Replaced. N/A
60320” with “the JIS C 8283 series of standards,
JIS C 8303 or JIS C 8358”.
4.5.3 In the item b in Table 4B, add the following: Replaced. P
NOTE If no data of material is available,
Appendix 4, 1(1),ロ,3 specified in the
Interpretation for “the Ministerial Ordinance
establishing Technical Requirements for
Electrical Appliances and Materials MEIT
Ordinance No. 85, Clause 1 (METI Ordinance
No. 34 of 2013)” is applicable.
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 46 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
J 60950-1(H26)
(Deviations from IEC 60950-1:2005, second edition)
Special National conditions, National deviation and other information according to MITI Ordinance No. 85.
Japanese unique deviations in J60950-1(H26) (=JIS C 6950-1:2012)
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 47 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
J 60950-1(H26)
(Deviations from IEC 60950-1:2005, second edition)
Special National conditions, National deviation and other information according to MITI Ordinance No. 85.
Japanese unique deviations in J60950-1(H26) (=JIS C 6950-1:2012)
th
Annex G.6 Replace the existing 8 paragraph with the The alternative method was not
following: considered. N/A
The above minimum CLEARANCES for
connectors do not apply to:
- connectors that comply with JIS C 8285, the
IEC 60309 series of standards, the JIS C
8283 series of standards, the IEC 60320
series of standards or JIS C 8303; and
- connectors that with the Ministerial Ordiance
establishing Technical Requirements for
Electrical Appliances and Materials (MEIT
Ordinance No. 34 of 2013) and comply with
the dimensions specified in the JIS C 8283
series of standards, JIS C 8303 or IEC 60309-
2;
see also 1.5.2.
Annex M In M.1, replace the existing paragraph with the No telephone ringing signals.
following: N/A
One of the two methods specified in this annex
shall be applied.
NOTE Method A specified in the annex is typical
of analogue telephone network in Europe and
Method B of those in North America.
Annex P Replace the existing Annex P with the following: Replaced. P
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 48 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
J 60950-1(H26)
(Deviations from IEC 60950-1:2005, second edition)
Special National conditions, National deviation and other information according to MITI Ordinance No. 85.
Japanese unique deviations in J60950-1(H26) (=JIS C 6950-1:2012)
Annex P
(normative)
Normative references
The following reference documents are indispensable for the application of this standard. If the date of the reference
document is given, only that edition applies, and any newer edition and subsequent amendments do not apply. If the date
of the reference document is not given, the latest edition including the amendments applies.
Further information on the reference documents, including how to obtain copies, can be found on the following internet
sites:
http://www.jisc.go.jp/
http://www.iec.ch
http://www.iso.org
http://www.itu.int
JIS B 0205-2, ISO general purpose metric screw threads - Part2: General plan
-
NOTE Corresponding IS: ISO 261, ISO general purpose metric screw threads General plan (IDT)
JIS B 0205-3, ISO general purpose metric screw threads - Part3 : Selected sizes for screws, bolts and nuts
,
NOTE Corresponding IS: ISO 262 ISO general purpose metric screw threads - Selected sizes for screws, bolts and nuts
(IDT)
JIS C 0448, Coding of indicating devices and actuators by colours and supplementary means
NOTE Corresponding IS: IEC 60073, Basic and safety principles for man-machine interface, marking and identification -
Coding principles for indicator devices and actuators (IDT)
JIS C 2134, Method for the determination of the proof and the comparative tracking indices of solid insulating materials
NOTE Corresponding IS: IEC 60112, Method for the determination of the proof and the comparative tracking indices of
insulating materials (IDT)
JIS C 3215 (all parts), Specifications for particular types of winding wires
NOTE Corresponding IS: IEC 60317 (all parts), Specifications for particular types of winding wires (IDT)
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 49 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
J 60950-1(H26)
(Deviations from IEC 60950-1:2005, second edition)
Special National conditions, National deviation and other information according to MITI Ordinance No. 85.
Japanese unique deviations in J60950-1(H26) (=JIS C 6950-1:2012)
JIS C 3661-1:1998, Electrical test methods for electric cables - Part 1: Electrical tests for cables, cords and wires for
voltages up to and including 450/750V
NOTE Corresponding IS: IEC 60885-1:1987, Electrical test methods for electric cables. Part 1: Electrical tests for cables,
cords and wires for voltages up to and including 450/750 V (IDT)
JIS C 3662 (all parts), Polyvinyl chloride insulated cables of rated voltages up to and including 450/750V - Part 1 : General
requirements
NOTE Corresponding IS: IEC 60227 (all parts), Polyvinyl chloride insulated cables of rated voltages up to and including
450/750 V (MOD)
JIS C 3663 (all parts), Rubber insulated cables - Rated voltages up to and including 450/750 V
NOTE Corresponding IS: IEC 60245 (all parts), Rubber insulated cables - Rated voltages up to and including 450/750 V
(MOD)
JIS C 4003, Electrical insulation-Thermal evaluation and designation
NOTE Corresponding IS: IEC 60085:2004, Electrical insulation - Thermal classification (MOD)
JIS C 4526-1:2005, Switches for appliances - Part 1: General requirements
NOTE Corresponding IS: IEC 61058-1:2000, Switches for appliances - Part 1: General requirements (MOD)
JIS C 5101-14:2009, Fixed capacitors for use in electronic equipment - Part 14: Sectional specification: Fixed capacitors
for electromagnetic interference suppression and connection to the supply mains
NOTE Corresponding IS: IEC 60384-14:2005, Fixed capacitors for use in electronic equipment - Part 14: Sectional
specification: Fixed capacitors for electromagnetic interference suppression and connection to the supply mains (IDT)
JIS C 6065:2007 and Amendment 1:2009, Audio, video and similar electronic apparatus - Safety requirements
NOTE Corresponding IS: IEC 60065:2001, Audio, video and similar electronic apparatus - Safety requirements and
Amendment 1:2005 (MOD)
JIS C 6802, Safety of laser products
JIS C 6803, Safety of laser products-Safety of optical fiber communication systems
JIS C 6804, Safety of laser products-Safety of free space optical communication systems used for transmission of
information
NOTE Corresponding IS: IEC 60825-12, Safety of laser products - Part 12: Safety of free space optical communication
systems used for transmission of information (IDT)
JIS C 8201-1:2007, Low-voltage switchgear and controlgear-Part 1: General rules
NOTE Corresponding IS: IEC 60947-1:2004, Low-voltage switchgear and controlgear - Part 1: General rules (MOD)
JIS C 8283 (all parts), Appliance couplers for household and similar general purposes
NOTE Corresponding IS: IEC 60320 (all parts), Appliances couplers for household and similar general purposes (MOD)
JIS C 8285, Plugs, socket-outlets and couplers for industrial purposes
NOTE Corresponding IS: IEC 60309-1, Plugs, socket-outlets and couplers for industrial purposes - Part 1: General
requirements (MOD)
JIS C 8303, Plugs and receptacles for domestic and similar general use
JIS C 8358:1994, Appliance couplers for domestic and similar use
JIS C 9730-1:2010, Automatic electrical controls for household and similar use - Part 1:General requirements
NOTE Corresponding IS: IEC 60730-1:1999, Automatic electrical controls for household and similar use - Part 1: General
requirements and Amendment 1:2003 (MOD)
JIS C 60068-2-78, Environmental testing - Test Cab:Damp heat,steady state
NOTE Corresponding IS: IEC 60068-2-78, Environmental testing - Part 2-78: Tests - Test Cab: Damp heat, steady state
(IDT)
JIS C 60364-1:2006, Low-voltage electrical installations - Part 1: Fundamental principles, assessment of general
characteristics, definitions
NOTE Corresponding IS: IEC 60364-1:2001, Electrical installations of buildings - Part 1: Fundamental principles,
assessment of general characteristics, definitions (IDT)
JIS C 60664-1:2009, Insulation coordination for equipment within low-voltage systems - Part 1:Principles,requirements
and tests
NOTE Corresponding IS: IEC 60664-1:1992, Insulation coordination for equipment within low-voltage systems - Part 1:
Principles, requirements and tests, Amendment 1:2000 and Amendment 2:2002 (IDT)
JIS C 60695-2-11, Fire hazard testing - Glow-wire flammability test method for end-products
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
NOTE Corresponding IS: IEC 60695-2-11, Fire hazard testing - Part 2-11: Glowing/hot-wire based test methods - Glow-
wire flammability test method for end-products (IDT)
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
- -
JIS C 60695-2-20, Fire hazard testing Part 2 : Glowing /Hot wire based test methods Section 20 : Hot-wire coil
ignitability test on materials
NOTE Corresponding IS: IEC/TS 60695-2-20, Fire hazard testing - Part 2-20: Glowing/hot wire based test methods - Hot-
Page 50 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
J 60950-1(H26)
(Deviations from IEC 60950-1:2005, second edition)
Special National conditions, National deviation and other information according to MITI Ordinance No. 85.
Japanese unique deviations in J60950-1(H26) (=JIS C 6950-1:2012)
JIS C 60695-10-2, Fire hazard testing-Part 10-2: Abnormal heat-Ball pressure test
NOTE Corresponding IS: IEC 60695-10-2, Fire hazard testing - Part 10-2: Abnormal heat - Ball pressure test (IDT)
JIS C 60695-11-5:2007, Fire hazard testing-Part 11-5:Test flames-Needle-flame test method - Apparatus, confirmatory
test arrangement and guidance
NOTE Corresponding IS: IEC 60695-11-5:2004, Fire hazard testing - Part 11-5: Test flames - Needle-flame test method -
Apparatus, confirmatory test arrangement and guidance (IDT)
JIS C 60695-11-10, Fire hazard testing-Part 11-10:Test flames - 50 W horizontal and vertical flame test methods
NOTE Corresponding IS: IEC 60695-11-10, Fire hazard testing - Part 11-10: Test flames - 50 W horizontal and vertical
flame test methods (IDT)
JIS C 60695-11-20, Fire hazard testing-Part 11-20: Test flames - 500 W flame test methods
NOTE Corresponding IS: IEC 60695-11-20, Fire hazard testing - Part 11-20: Test flames - 500 W flame test methods
(IDT)
JIS K 7110, Plastics - Determinaion of Izod impact strength
NOTE Corresponding IS: ISO 180, Plastics - Determination of Izod impact strength (MOD)
JIS K 7111 (all parts), Plastics-Determination of Charpy impact properties - Part 1: Non-instrumented impact test
NOTE Corresponding IS: ISO 179 (all parts), Plastics - Determination of Charpy impact properties (MOD)
-
JIS K 7127, Plastics - Determination of tensile properties Part 3 : Test conditions for films and sheets
NOTE Corresponding IS: ISO 527-3, Plastics - Determination of tensile properties - Part 3: Test conditions for films and
sheets (IDT)
-
JIS K 7160, Plastics Determination of tensile-impact strength
NOTE Corresponding IS: ISO 8256, Plastics - Determination of tensile-impact strength (IDT)
- -
JIS K 7161, Plastics Determination of tensile properties Part 1 : General principles
NOTE Corresponding IS: ISO 527-1, Plastics - Determination of tensile properties - Part 1: General principles (IDT)
JIS K 7162, Plastics - Determination of tensile properties - Part 2 : Test conditions for moulding and extrusion plastics
NOTE Corresponding IS: ISO 527-2, Plastics - Determination of tensile properties - Part 2: Test conditions for moulding
and extrusion plastics (IDT)
JIS K 7164, Plastics - Determination of tensile properties - Test conditions for isotropic and orthotropic fibre-reinforced
plastic composites
NOTE Corresponding IS: ISO 527-4, Plastics - Determination of tensile properties - Part 4: Test conditions for isotropic
and orthotropic fibre-reinforced plastic composites (MOD)
JIS K 7165, Plastics-Determination of tensile properties-Part 5: Test conditions for unidirectional fibre-reinforced plastic
composites
NOTE Corresponding IS: ISO 527-5, Plastics - Determination of tensile properties - Part 5: Test conditions for
unidirectional fibre-reinforced plastic composites (MOD)
JIS K 7171, Plastics - Determination of flexural properties
NOTE Corresponding IS: ISO 178, Plastics - Determination of flexural properties (IDT)
JIS K 7241, Cellular plastics-Determination of horizontal burning characteristics of small specimens subjected to a small
flame
NOTE Corresponding IS: ISO 9772, Cellular plastics - Determination of horizontal burning characteristics of small
specimens subjected to a small flame (IDT)
JIS K 7341, Plastics-Determination of burning behaviour of thin flexible vertical specimens in contact with a small-flame
ignition source
NOTE Corresponding IS: ISO 9773, Plastics - Determination of burning behaviour of thin flexible vertical specimens in
contact with a small-flame ignition source (IDT)
JIS K 7350-1, Plastics - Methods of exposure to laboratory light sources - Part 1: General guidance
NOTE Corresponding IS: ISO 4892-1, Plastics - Methods of exposure to laboratory light sources - Part 1: General
guidance (IDT)
JIS K 7350-2, Plastics - Methods of exposure to laboratory light sources - Part 2 : Xenon-arc lamps
NOTE Corresponding IS: ISO 4892-2, Plastics - Methods of exposure to laboratory light sources - Part 2: Xenon-arc
lamps (MOD)
JIS K 7350-4, Plastics - Methods of exposure to laboratory light sources - Part 4: Open-flame carbon-arc lamps
NOTE Corresponding IS: ISO 4892-4, Plastics - Methods of exposure to laboratory light sources - Part 4: Open-flame
carbon-arc lamps (MOD) TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
JIS S 0101:2000, Graphical warning symbols for consumers
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
TS C 60695-11-3, Fire hazard testing - Part 11-3: Test flames - 500 W flames - Apparatus and confirmational test
methods
NOTE Corresponding IS: IEC 60695-11-3, Fire hazard testing - Part 11-3: Test flames - 500 W flames - Apparatus and
confirmational test methods (IDT)
Page 51 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
J 60950-1(H26)
(Deviations from IEC 60950-1:2005, second edition)
Special National conditions, National deviation and other information according to MITI Ordinance No. 85.
Japanese unique deviations in J60950-1(H26) (=JIS C 6950-1:2012)
TS C 60695-11-4, Fire hazard testing - Part 11-4: Test flames - 50 W flames - Apparatus and confirmational test methods
NOTE Corresponding IS: IEC 60695-11-4, Fire hazard testing - Part 11-4: Test flames - 50 W flames - Apparatus and
confirmational test methods (IDT)
IEC 60216-4-1, Electrical insulating materials - Thermal endurance properties - Part 4-1: Ageing ovens - Single-chamber
ovens
IEC 60309 (all parts), Plugs, socket-outlets and couplers for industrial purposes
IEC 60317 (all parts), Specifications for particular types of winding wires
IEC 60317-43, Specifications for particular types of winding wires - Part 43: Aromatic polyimide tape wrapped round
copper wire, class 240
IEC 60320 (all parts), Appliance couplers for household and similar general purposes
IEC 60417-DB:2002, Graphical symbols for use on equipment
(For DB, see the online database of the IEC.)
IEC 60747-5-5, Semiconductor devices - Discrete devices - Part 5-5: Optoelectronic devices – Photocouplers
IEC 60825-1, Safety of laser products - Part 1: Equipment classification and requirements
IEC 60825-2, Safety of laser products - Part 2: Safety of optical fibre communication systems (OFCS)
IEC/TR 60825-9, Safety of laser products - Part 9: Compilation of maximum permissible exposure to incoherent optical
radiation
IEC 60851-3:1996, Winding wires - Test methods - Part 3: Mechanical properties and Amendment 1:1997
IEC 60851-5:1996, Winding wires - Test methods - Part 5: Electrical properties, Amendment 1:1997 and Amendment
2:2004
IEC 60851-6:1996, Methods of test for winding wires - Part 6: Thermal properties
IEC 60947-1:2004, Low-voltage switchgear and controlgear - Part 1: General rules
IEC 60990:1999, Methods of measurement of touch current and protective conductor current
IEC 61051-2, Varistors for use in electronic equipment - Part 2: Sectional specification for surge suppression varistors
ISO 180, Plastics - Determination of Izod impact strength
ISO 4892-1, Plastics - Methods of exposure to laboratory light sources - Part 1: General guidance
ISO 7000-DB:2004, Graphical symbols for use on equipment - Index and synopsis
(For DB, see the online database of the IEC.)
ISO 8256, Plastics - Determination of tensile-impact strength
ITU-T Recommendation K.44, Resistibility tests for telecommunication equipment exposed to overvoltages and
overcurrents - Basic Recommendation
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 52 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
J 60950-1(H26)
(Deviations from IEC 60950-1:2005, second edition)
Special National conditions, National deviation and other information according to MITI Ordinance No. 85.
Japanese unique deviations in J60950-1(H26) (=JIS C 6950-1:2012)
Annex W.1 Replace second and third sentence in the first Replaced. N/A
paragraph with the following:
This distinction between earthed and unearthed
(floating) circuit is not the same as between
CLASS I EQUIMENT, CLASS 0I EQUIPMENT
and CLASS II EQUIPMENT. Floating circuits can
exist in CLASS I EQUIPMENT or CLASS 0I
EQUIPMENT and earthed circuits in CLASS II
EQUIPMENT.
Annex AA Replace figure AA.3 which correct the position of Replaced. N/A
insulating metal sheet.
Annex JA Add a new annex JA with the following contents. Not document shredding N/A
machine.
Annex JA
(normative)
Requirements for document shredding machines
(see 1.7, 2.8.3, 3.4 and 4.4)
Introduction
This annex specifies the safety requirements for
document shredding machines, except those of
STATIONARY EQUIPMENT used by connecting
directly to 3-phase AC MAINS SUPPLY of a
voltage not the than 200V.
Document shredding machines shall comply with
the requirements of this annex in addition to other
requirements specified in this standard, except
those of STATIONARY EQUIPMENT used by
connecting directly to three-phase AC MAINS
SUPPLY of a voltage not less than 200V.
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 53 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
J 60950-1(H26)
(Deviations from IEC 60950-1:2005, second edition)
Special National conditions, National deviation and other information according to MITI Ordinance No. 85.
Japanese unique deviations in J60950-1(H26) (=JIS C 6950-1:2012)
JA.1 Markings and instructions N/A
In the easily visible part near to the slot for
documents, by a method of clearly legible and
permanent and by using easily understandable
terms, document shredding machines shall have
markings of the symbol specified in 6.2.1
(general cautions) of JIS S 0101:2000, Graphical
warning symbols for consumers, and also the
following precautions for use:
- that use by an infants/children may cause a
hazard of injury etc.;
- that a hand can be drawn into the mechanical
section for shredding when touching the
document-slot;
- that clothing can be drawn into the mechanical
section for shredding when touching the
document-slot;
- that hairs can be drawn into the mechanical
section for shredding when touching the
document-slot;
- in case of equipment incorporating a
commutator motor, that equipment may catch
fire or explode by spraying of flammable gas.
JA.2 Inadvertent reactivation N/A
Any safety interlock that can be operated by
means of the test finger, Figure JA.1, is
considered to be likely to cause inadvertent
reactivation of the hazard.
Compliance is checked by inspection and, where
necessary, by a test with the test finger, Figure
JA.1
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 54 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
J 60950-1(H26)
(Deviations from IEC 60950-1:2005, second edition)
Special National conditions, National deviation and other information according to MITI Ordinance No. 85.
Japanese unique deviations in J60950-1(H26) (=JIS C 6950-1:2012)
JA.3 Disconnect switch N/A
Document shredding machines shall incorporate
an isolating switch complying with sub-clause
3.4.2 as the device disconnecting the power of
hazardous moving parts. For this switch, two-
position (single-use) switch or multi-position
(multifunction) switch (e.g., slide switch) may be
used.
If two-position switch, the positions for “ON” and
“OFF” shall be indicated in accordance with sub-
clause 1.7.8. If multi-position switch, the position
for “OFF” shall be indicated in accordance with
sub-clause 1.7.8 and other positions shall be
indicated with proper terms or symbols.
Compliance is checked by inspection.
JA.4 Protection in operator access area N/A
Any warning shall not be used instead of the
structure for preventing access to hazardous
moving parts.
Document shredding machines shall comply with
the following requirements.
Insert the test finger, Figure JA.1, into all
openings in MECHANICAL ENCLOSURES
without applying appreciable force. It shall not be
possible to touch hazardous moving parts with
the test finger. This consideration applies to all
sides of MECHANICAL ENCLOSURES when the
equipment is mounted as intended . Before
testing with the test finger, remove the parts
detachable without a tool.
Insert the wedge-probe, Figure JA.2, into the
document-slot. And, against all directions of
openings, if straight-cutting type, a force of 45 N
shall apply to the probe, and 90 N if cross-cutting
type. In this case, the weight of the probe is to be
factored into the overall applied force. Before
testing with the wedge-probe, remove the parts
detachable without a tool. It shall not be possible
to touch any hazardous moving parts, including
the shredding roller or the mechanical section for
shedding, with the probe.
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 55 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
J 60950-1(H26)
(Deviations from IEC 60950-1:2005, second edition)
Special National conditions, National deviation and other information according to MITI Ordinance No. 85.
Japanese unique deviations in J60950-1(H26) (=JIS C 6950-1:2012)
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 56 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
J 60950-1(H26)
(Deviations from IEC 60950-1:2005, second edition)
Special National conditions, National deviation and other information according to MITI Ordinance No. 85.
Japanese unique deviations in J60950-1(H26) (=JIS C 6950-1:2012)
Dimensions in millimeters
Distance from the tip Thickness of probe
0 2
12 4
180 24
The thickness of the probe varies linearly, except changing the slope at the respective points shown in the table.
The allowable dimensional tolerance of the probe shall be +/- 0,127 mm.
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 57 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
J 60950-1(H26)
(Deviations from IEC 60950-1:2005, second edition)
Special National conditions, National deviation and other information according to MITI Ordinance No. 85.
Japanese unique deviations in J60950-1(H26) (=JIS C 6950-1:2012)
Annex JB Add Annex JB as follows: N/A
Annex JB
(informative)
Current conditions Installation environment on
overvoltages and overcurrents, and the measures
(see NOTE 1 in Clause 6)
Introduction
This standard is based on “ITU-T
Recommendation K.11:1993” to stipulate
requirement for equipment on a premise to install
in the environment where appropriate measures
were taken for so that overvoltage more than
peak 1.5kV does not hang to the apparatus. But
in Japan due to environment is difficult to
integrate with “ITU-T Recommendation
K.11:1993”, in here explain for desirable
environment and show actions to be taken how to
make a desirable setting environment.
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 58 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
J 60950-1(H26)
(Deviations from IEC 60950-1:2005, second edition)
Special National conditions, National deviation and other information according to MITI Ordinance No. 85.
Japanese unique deviations in J60950-1(H26) (=JIS C 6950-1:2012)
JB.1 A desirable setting environment N/A
When lead electric wires in building for any kind
service of metal wire, for overvoltage restraint and
overcurrent restraint, it is desirable that be close to
each other including grounding conductor. It is
important to make it close each other especially the
lead in point of power line, communication line and
grounding conductor. In that case, attention is
necessary for electromagnetic induction where
occurred between a communication line and the
power line which are not covered. It is desirable
that set up main grounding terminal which close to
lead in point of power line and communication line
in building as much as possible. Due to minimize
the surge current in building for all shielding
conductor of cable which lead in building, it shall
connected directly with main grounding terminal in
lead in point via surge protection device (SPD) e.g.
arrester and so on. It shall be considered corrosion
measures in joint if necessary.
It is desirable that SPD which set on
communication line is close to lead in point
toward the building as much as possible.
Furthermore set the SPD near the main power
line, and it may make the distance from SPD to a
grounding conductor as short as possible. It is
effective if use a short grounding conductor with
low impedance for that decrease surge voltage
between electric power system protection
conductor and the communication line.
Desirable setting environment for TT electric N/A
power system is as figure JB.1. Established SPD
as that excessive potential difference does not
occur between communication side and the
electricity side, and recommend that ground wire
of both are connected with a short conductor.
Concerning the detail for recommend setting
environment, see
ITU-T Recommendation K.11:1993, K.21:1996,
K.27:1996, K.31:1993 and K.66:2004.
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 59 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
J 60950-1(H26)
(Deviations from IEC 60950-1:2005, second edition)
Special National conditions, National deviation and other information according to MITI Ordinance No. 85.
Japanese unique deviations in J60950-1(H26) (=JIS C 6950-1:2012)
Note:
a) All bonding line to a main grounding terminal makes it as short as possible (Less than 1.5m in the place that
danger of direct lightning is high).
b) The connected line which from SPD to main grounding terminal is as short as possible (less 1.5m).
c) Setting for SPD (omitted the detail). All SPD connected line is short as possible (less 0.5m).
Figure JB.1 – Sample of desirable setting for TT electric power system of single phase three-wire type + neutral
line
(From ITU-T Recommendation K.66:2004)
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 60 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
J 60950-1(H26)
(Deviations from IEC 60950-1:2005, second edition)
Special National conditions, National deviation and other information according to MITI Ordinance No. 85.
Japanese unique deviations in J60950-1(H26) (=JIS C 6950-1:2012)
But as thing are stand, there are a lot of cases that N/A
an outlet is not prepared with the grounding
terminal which is appropriate in the setting place of
the equipment. On the other hand, grounding
resistance value of SPD where set at lead-in point
of communication line sometime is not enough low,
it make that dielectric breakdown was occurred
due to the voltage that a thunder surge current
evoked for grounding resistance which flow into the
communication line and drift to the ground through
SPD. The same result is expected that grounding
resistance value is not enough low too if set SPD
on electric power system. This status is as figure
JB.3.
As figure JB.1, it can decrease effectively by
connecting both with the conductor of the low
resistance value when excessive potential
difference occurred in internal equipment.
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 61 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
J 60950-1(H26)
(Deviations from IEC 60950-1:2005, second edition)
Special National conditions, National deviation and other information according to MITI Ordinance No. 85.
Japanese unique deviations in J60950-1(H26) (=JIS C 6950-1:2012)
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 62 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
KR Republic of Korea KR
1.5.101 Addition N/A
Plugs for the connection of the apparatus to the
supply mains shall comply with the Korean
requirement (KSC 8305).
8 Addition N/A
EMC The apparatus shall comply with the relevant
CISPR standards
SE Sweden SE
1.2.13.14 In Norway and Sweden, for requirements see N/A
1.7.2.1 and 7.3 of this annex.
1.5.1 Sweden (Ordinance 1990:944) N/A
Add the following:
NOTE In Sweden, switches containing mercury
are not permitted.
1.5.7.1 In Finland, Norway and Sweden, resistors N/A
bridging BASIC INSULATION in CLASS I PLUGGABLE
EQUIPMENT TYPE A must comply with the
requirements in 1.5.7.1. In addition when a single
resistor is used, the resistor must withstand the
resistor test in 1.5.7.2.
1.5.9.4 In Finland, Norway and Sweden, the third dashed N/A
sentence is applicable only to equipment as
defined in 6.1.2.2 of this annex.
1.7.2.1 In Finland, Norway and Sweden, CLASS I N/A
PLUGGABLE EQUIPMENT TYPE A intended for
connection to other equipment or a network shall,
if safety relies on connection to protective earth or
if surge suppressors are connected between the
network terminals and accessible parts, have a
marking stating that the equipment must be
connected to an earthed mains socket-outlet.
The marking text in the applicable countries shall N/A
be as follows:
In Finland:
"Laite on liitettävä suojamaadoituskoskettimilla
varustettuun pistorasiaan"
In Norway:
“Apparatet må tilkoples jordet stikkontakt”
In Sweden:
“Apparaten skall anslutas till jordat uttag”
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 63 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
SE Sweden SE
1.7.2 In Norway and Sweden, the screen of the cable N/A
distribution system is normally not earthed at the
entrance of the building and there is normally no
equipotential bonding system within the building.
Therefore the protective earthing of the building
installation need to be isolated from the screen of
a cable distribution system.
It is however accepted to provide the insulation
external to the equipment by an adapter or an
interconnection cable with galvanic isolator, which
may be provided by e.g. a retailer.
The user manual shall then have the following or
similar information in Norwegian and Swedish
language respectively, depending on in what
country the equipment is intended to be used in:
“Equipment connected to the protective
earthing of the building installation through the
mains connection or through other equipment
with a connection to protective earthing – and
to a cable distribution system using coaxial
cable, may in some circumstances create a
fire hazard. Connection to a cable distribution
system has therefore to be provided through a
device providing electrical isolation below a
certain frequency range (galvanic isolator, see
EN 60728-11).”
NOTE In Norway, due to regulation for installations of cable
distribution systems, and in Sweden, a galvanic isolator shall
provide electrical insulation below 5 MHz. The insulation shall
withstand a dielectric strength of 1,5 kV r.m.s., 50 Hz or 60
Hz, for 1 min.
Translation to Norwegian (the Swedish text will
also be accepted in Norway):
“Utstyr som er koplet til beskyttelsesjord via
nettplugg og/eller via annet jordtilkoplet utstyr
– og er tilkoplet et kabel-TV nett, kan forårsake
brannfare. For å unngå dette skal det ved
tilkopling av utstyret til kabel-TV nettet
installeres en galvanisk isolator mellom
utstyret og kabel- TV nettet.”
Translation to Swedish:
”Utrustning som är kopplad till skyddsjord via
jordat vägguttag och/eller via annan utrustning
och samtidigt är kopplad till kabel-TV nät kan i
vissa fall medfőra risk főr brand. Főr att
undvika detta skall vid anslutning av
utrustningen till kabel-TV nät galvanisk isolator
finnas mellan utrustningen och kabel-TV
nätet.”
2.3.2 In Finland, Norway and Sweden there are N/A
additional requirements for the insulation. See
6.1.2.1 and 6.1.2.2 of this annex.
2.10.5.13 In Finland, Norway and Sweden, there are N/A
additional requirements for the insulation, see
6.1.2.1 and 6.1.2.2 of this annex.
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 64 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
SE Sweden SE
5.1.7.1 In Finland, Norway and Sweden TOUCH N/A
CURRENT measurement results exceeding 3,5
mA r.m.s. are permitted only for the following
equipment:
STATIONARY PLUGGABLE EQUIPMENT TYPE
A that is intended to be used in a RESTRICTED
ACCESS LOCATION where equipotential
bonding has been applied, for example, in a
telecommunication centre; and
has provision for a permanently connected
PROTECTIVE EARTHING CONDUCTOR; and
is provided with instructions for the installation of
that conductor by a SERVICE PERSON;
STATIONARY PLUGGABLE EQUIPMENT TYPE
B;
STATIONARY PERMANENTLY CONNECTED
EQUIPMENT.
6.1.2.1 In Finland, Norway and Sweden, add the N/A
following text between the first and second
paragraph of the compliance clause:
If this insulation is solid, including insulation
forming part of a component, it shall at least
consist of either
- two layers of thin sheet material, each of
which shall pass the electric strength test
below, or
- one layer having a distance through insulation
of at least 0,4 mm, which shall pass the
electric strength test below.
If this insulation forms part of a semiconductor
component (e.g. an optocoupler), there is no
distance through insulation requirement for the
insulation consisting of an insulating compound
completely filling the casing, so that
CLEARANCES and CREEPAGE DISTANCES do
not exist, if the component passes the electric
strength test in accordance with the compliance
clause below and in addition
- passes the tests and inspection criteria of
2.10.11 with an electric strength test of 1,5 kV
multiplied by 1,6 (the electric strength test of
2.10.10 shall be performed using 1,5 kV), and
- is subject to ROUTINE TESTING for electric
strength during manufacturing, using a test
voltage of 1,5 kV.
It is permitted to bridge this insulation with a
capacitor complying with EN 132400:1994,
subclass Y2.
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 65 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
SE Sweden SE
A capacitor classified Y3 according to EN N/A
132400:1994, may bridge this insulation under
the following conditions:
- the insulation requirements are satisfied by
having a capacitor classified Y3 as defined by
EN 132400, which in addition to the Y3
testing, is tested with an impulse test of 2,5
kV defined in EN 60950-1:2006, 6.2.2.1;
- the additional testing shall be performed on
all the test specimens as described in EN
132400;
- the impulse test of 2,5 kV is to be performed
before the endurance test in EN 132400, in
the sequence of tests as described in EN
132400.
6.1.2.2 In Finland, Norway and Sweden, the exclusions N/A
are applicable for PERMANENTLY CONNECTED
EQUIPMENT, PLUGGABLE EQUIPMENT TYPE
B and equipment intended to be used in a
RESTRICTED ACCESS LOCATION where
equipotential bonding has been applied, e.g. in a
telecommunication centre, and which has
provision for a permanently connected
PROTECTIVE EARTHING CONDUCTOR and is
provided with instructions for the installation of
that conductor by a SERVICE PERSON.
7.2 In Finland, Norway and Sweden, for requirements N/A
see 6.1.2.1 and 6.1.2.2 of this annex. The term
TELECOMMUNICATION NETWORK in 6.1.2
being replaced by the term CABLE
DISTRIBUTION SYSTEM.
7.3 In Norway and Sweden, there are many buildings N/A
where the screen of the coaxial cable is normally
not connected to the earth in the building
installation.
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 66 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
UA Ukraine UA
1.4.5 In Ukraine the NOMINAL VOLTAGE is 220 V for Rated voltage: 100-240VAC P
monophase or 380 V for three-phase supply.
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 67 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 68 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 69 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 70 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 71 of 71
Report No.: 085-110044304-000
Attachment No. 1
IEC60950-1
Clause Requirement + Test Result - Remark Verdict
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Test Report National and Group Differences for IEC 60950-1 2nd Ed.+A1+A2 Rev. 07
Page 1 of 19
Report No.: 085-110044304-000
Attachment No. 2
IEC60950_1F - ATTACHMENT
Clause Requirement + Test Result - Remark Verdict
3.3.4 In Table 3D, delete the fourth line: conductor sizes N/A
for 10 to 13 A, and replace with the following:
Over 10 up to and including 16 | 1,5 to 2,5 | 1,5 to
4 |
Delete the fifth line: conductor sizes for 13 to 16 A
4.3.13.6 Replace the existing NOTE by the following: N/A
(A1:2010) NOTE Z1 Attention is drawn to:
1999/519/EC: Council Recommendation on the
limitation of exposure of the general public to
electromagnetic fields 0 Hz to 300 GHz, and
2006/25/EC: Directive on the minimum health and
safety requirements regarding the exposure of workers
to risks arising from physical agents (artifical optical
radiation).
Standards taking into account mentioned N/A
Recommendation and Directive which demonstrate
compliance with the applicable EU Directive are
indicated in the OJEC.
Annex H Replace the last paragraph of this annex by: N/A
At any point 10 cm from the surface of the
OPERATOR ACCESS AREA, the dose rate shall
not exceed 1 µSv/h (0,1 mR/h) (see NOTE).
Account is taken of the background level.
Replace the notes as follows:
NOTE These values appear in Directive 96/29/Euratom.
Delete NOTE 2.
Bibliography Additional EN standards.
ZB ANNEX (normative)
SPECIAL NATIONAL CONDITIONS (EN)
Clause Requirement + Test Result - Remark Verdict
1.2.4.1 In Denmark, certain types of Class I appliances N/A
(see 3.2.1.1) may be provided with a plug not
establishing earthing conditions when inserted
into Danish socket-outlets.
1.2.13.14 In Norway and Sweden, for requirements see N/A
(A11:2009) 1.7.2.1 and 7.3 of this annex.
Page 10 of 19
Report No.: 085-110044304-000
Attachment No. 2
IEC60950_1F - ATTACHMENT
Clause Requirement + Test Result - Remark Verdict
ZB ANNEX (normative)
SPECIAL NATIONAL CONDITIONS (EN)
Clause Requirement + Test Result - Remark Verdict
1.5.7.1 In Finland, Norway and Sweden, resistors N/A
(A11:2009) bridging BASIC INSULATION in CLASS I PLUGGABLE
EQUIPMENT TYPE A must comply with the
requirements in 1.5.7.1. In addition when a single
resistor is used, the resistor must withstand the
resistor test in 1.5.7.2.
1.5.8 In Norway, due to the IT power system used (see P
annex V, Figure V.7), capacitors are required to
be rated for the applicable line-to-line voltage
(230 V).
1.5.9.4 In Finland, Norway and Sweden, the third N/A
dashed sentence is applicable only to equipment
as defined in 6.1.2.2 of this annex.
Page 11 of 19
Report No.: 085-110044304-000
Attachment No. 2
IEC60950_1F - ATTACHMENT
Clause Requirement + Test Result - Remark Verdict
ZB ANNEX (normative)
SPECIAL NATIONAL CONDITIONS (EN)
Clause Requirement + Test Result - Remark Verdict
1.7.2.1 In Finland, Norway and Sweden, CLASS I N/A
PLUGGABLE EQUIPMENT TYPE A intended for
connection to other equipment or a network shall,
if safety relies on connection to protective earth or
if surge suppressors are connected between the
network terminals and accessible parts, have a
marking stating that the equipment must be
connected to an earthed mains socket-outlet.
The marking text in the applicable countries shall
be as follows:
In Finland: "Laite on liitettävä suojakoskettimilla
varustettuun pistorasiaan"
In Norway: “Apparatet må tilkoples jordet
stikkontakt”
In Sweden: “Apparaten skall anslutas till jordat
uttag”
ZB ANNEX (normative)
SPECIAL NATIONAL CONDITIONS (EN)
Clause Requirement + Test Result - Remark Verdict
NOTE In Norway, due to regulation for installations of cable N/A
distribution systems, and in Sweden, a galvanic isolator shall
provide electrical insulation below 5 MHz. The insulation shall
withstand a dielectric strength of 1,5 kV r.m.s., 50 Hz or 60 Hz,
for 1 min.
Translation to Norwegian (the Swedish text will
also be accepted in Norway):
“Utstyr som er koplet til beskyttelsesjord via
nettplugg og/eller via annet jordtilkoplet
utstyr – og er tilkoplet et kabel-TV nett, kan
forårsake brannfare. For å unngå dette skal det
ved tilkopling av utstyret til kabel-TV nettet
installeres en galvanisk isolator mellom utstyret
og kabel- TV nettet.”
Translation to Swedish:
”Utrustning som är kopplad till skyddsjord via
jordat vägguttag och/eller via annan
utrustning och samtidigt är kopplad till kabel-TV
nät kan i vissa fall medfőra risk főr
brand. Főr att undvika detta skall vid anslutning
av utrustningen till kabel-TV nät
galvanisk isolator finnas mellan utrustningen och
kabel-TV nätet.”
1.7.2.1 In Denmark, CLASS I PLUGGABLE N/A
(A2:2013) EQUIPMENT TYPE A intended for connection to
other equipment or a network shall, if safety relies
on connection to protective earth or if surge
suppressors are connected between the network
terminals and accessible parts, have a marking
stating that the equipment must be connected to
an earthed mains socket-outlet.
The marking text in Denmark shall be as follows:
In Denmark: “Apparatets stikprop skal tilsluttes
en stikkontakt med jord, som giver forbindelse til
stikproppens jord.”
1.7.5 In Denmark, socket-outlets for providing power to N/A
other equipment shall be in accordance with the
Heavy Current Regulations, Section 107-2-D1,
Standard Sheet DK 1-3a, DK 1-5a or DK 1-7a,
when used on Class I equipment. For
STATIONARY EQUIPMENT the socket-outlet
shall be in accordance with Standard Sheet DK 1-
1b or DK 1-5a.
1.7.5 For CLASS II EQUIPMENT the socket outlet shall be
(A11:2009)
in accordance with Standard Sheet DKA 1-4a.
Page 13 of 19
Report No.: 085-110044304-000
Attachment No. 2
IEC60950_1F - ATTACHMENT
Clause Requirement + Test Result - Remark Verdict
ZB ANNEX (normative)
SPECIAL NATIONAL CONDITIONS (EN)
Clause Requirement + Test Result - Remark Verdict
1.7.5 In Denmark, socket-outlets for providing power to N/A
(A2:2013) other equipment shall be in accordance with the
DS 60884-2-D1:2011.
For class I equipment the following Standard
Sheets are applicable: DK 1-3a, DK 1-1c,
DK 1-1d, DK 1-5a or DK 1-7a, with the exception
for STATIONARY EQUIPMENT where the
socket-outlets shall be in accordance with
Standard Sheet DK 1-1b, DK 1-1c, DK 1-1d or
DK 1-5a.
Socket outlets intended for providing power to
Class II apparatus with a rated current of 2,5 A
shall be in accordance with DS 60884-2-D1
standard sheet DKA 1-4a. Other current rating
socket outlets shall be in compliance with by
DS 60884-2-D1 Standard Sheet DKA 1-3a or
DKA 1-3b.
Justification
the Heavy Current Regulations, 6c
2.2.4 In Norway, for requirements see 1.7.2.1, 6.1.2.1 N/A
and 6.1.2.2 of this annex.
2.3.2 In Finland, Norway and Sweden there are N/A
additional requirements for the insulation. See
6.1.2.1 and 6.1.2.2 of this annex.
2.3.4 In Norway, for requirements see 1.7.2.1, 6.1.2.1 N/A
and 6.1.2.2 of this annex.
2.6.3.3 In the United Kingdom, the current rating of the N/A
circuit shall be taken as 13 A, not 16 A.
2.7.1 In the United Kingdom, to protect against P
excessive currents and short-circuits in the
PRIMARY CIRCUIT of DIRECT PLUG-IN
EQUIPMENT, tests according to 5.3 shall be
conducted, using an external protective device
rated 30 A or 32 A. If these tests fail, suitable
protective devices shall be included as integral
parts of the DIRECT PLUG-IN EQUIPMENT, so
that the requirements of 5.3 are met.
2.10.5.13 In Finland, Norway and Sweden, there are N/A
additional requirements for the insulation, see
6.1.2.1 and 6.1.2.2 of this annex.
Page 14 of 19
Report No.: 085-110044304-000
Attachment No. 2
IEC60950_1F - ATTACHMENT
Clause Requirement + Test Result - Remark Verdict
ZB ANNEX (normative)
SPECIAL NATIONAL CONDITIONS (EN)
Clause Requirement + Test Result - Remark Verdict
3.2.1.1 In Switzerland, supply cords of equipment having N/A
a RATED CURRENT not exceeding 10 A shall be
provided with a plug complying with SEV 1011 or
IEC 60884-1 and one of the following dimension
sheets:
SEV 6532-2.1991 Plug Type 15 3P+N+PE
250/400 V, 10 A
SEV 6533-2.1991 Plug Type 11 L+N
250 V, 10 A
SEV 6534-2.1991 Plug Type 12 L+N+PE
250 V, 10 A
In general, EN 60309 applies for plugs for
currents exceeding 10 A. However, a 16 A plug
and socket-outlet system is being introduced in
Switzerland, the plugs of which are according to
the following dimension sheets, published in
February 1998:
SEV 5932-2.1998: Plug Type 25 , 3L+N+PE
230/400 V, 16 A
ZB ANNEX (normative)
SPECIAL NATIONAL CONDITIONS (EN)
Clause Requirement + Test Result - Remark Verdict
3.2.1.1 In Denmark, supply cords of single-phase N/A
(A2:2013) equipment having a rated current not exceeding
13 A shall be provided with a plug according to
DS 60884-2-D1.
CLASS I EQUIPMENT provided with socket-
outlets with earth contacts or which are intended
to be used in locations where protection against
indirect contact is required according to the wiring
rules shall be provided with a plug in accordance
with standard sheet DK 2-1a or DK 2-5a.
If a single-phase equipment having a RATED
CURRENT exceeding 13 A or if a poly-phase
equipment is provided with a supply cord with a
plug, this plug shall be in accordance with the
standard sheets DK 6-1a in DS 60884-2-D1 or
EN 60309-2.
Justification
the Heavy Current Regulations, 6c
3.2.1.1 In Spain, supply cords of single-phase equipment N/A
having a rated current not exceeding 10 A shall
be provided with a plug according to UNE
20315:1994.
Supply cords of single-phase equipment having a
rated current not exceeding 2,5 A shall be
provided with a plug according to UNE-EN
50075:1993.
CLASS I EQUIPMENT provided with socket-
outlets with earth contacts or which are intended
to be used in locations where protection against
indirect contact is required according to the wiring
rules, shall be provided with a plug in accordance
with standard UNE 20315:1994.
If poly-phase equipment is provided with a supply
cord with a plug, this plug shall be in accordance
with UNE-EN 60309-2.
3.2.1.1 In the United Kingdom, apparatus which is fitted P
with a flexible cable or cord and is designed to be
connected to a mains socket conforming to BS
1363 by means of that flexible cable or cord and
plug, shall be fitted with a ‘standard plug’ in
accordance with Statutory Instrument 1768:1994 -
The Plugs and Sockets etc. (Safety) Regulations
1994, unless exempted by those regulations.
NOTE ‘Standard plug’ is defined in SI 1768:1994 and
essentially means an approved plug conforming to BS
1363 or an approved conversion plug.
Page 16 of 19
Report No.: 085-110044304-000
Attachment No. 2
IEC60950_1F - ATTACHMENT
Clause Requirement + Test Result - Remark Verdict
ZB ANNEX (normative)
SPECIAL NATIONAL CONDITIONS (EN)
Clause Requirement + Test Result - Remark Verdict
3.2.1.1 In Ireland, apparatus which is fitted with a flexible N/A
cable or cord and is designed to be connected to
a mains socket conforming to I.S. 411 by means
of that flexible cable or cord and plug, shall be
fitted with a 13 A plug in accordance with
Statutory Instrument 525:1997 - National
Standards Authority of Ireland (section 28) (13 A
Plugs and Conversion Adaptors for Domestic
Use) Regulations 1997.
3.2.4 In Switzerland, for requirements see 3.2.1.1 of N/A
this annex.
3.2.5.1 In the United Kingdom, a power supply cord with N/A
conductor of 1,25 mm2 is allowed for equipment
with a rated current over 10 A and up to and
including 13 A.
3.3.4 In the United Kingdom, the range of conductor N/A
sizes of flexible cords to be accepted by terminals
for equipment with a RATED CURRENT of over
10 A up to and including 13 A is:
2 2
• 1,25 mm to 1,5 mm nominal cross-sectional
area.
4.3.6 In the United Kingdom, the torque test is P
performed using a socket outlet complying with
BS 1363 part 1:1995, including Amendment
1:1997 and Amendment 2:2003 and the plug part
of DIRECT PLUG-IN EQUIPMENT shall be
assessed to BS 1363: Part 1, 12.1, 12.2, 12.3,
12.9, 12.11, 12.12, 12.13, 12.16 and 12.17,
except that the test of 12.17 is performed at not
less than 125 °C. Where the metal earth pin is
replaced by an Insulated Shutter Opening Device
(ISOD), the requirements of clauses 22.2 and 23
also apply.
4.3.6 In Ireland, DIRECT PLUG-IN EQUIPMENT is N/A
known as plug similar devices. Such devices shall
comply with Statutory Instrument 526:1997 -
National Standards Authority of Ireland (Section
28) (Electrical plugs, plug similar devices and
sockets for domestic use) Regulations, 1997.
Page 17 of 19
Report No.: 085-110044304-000
Attachment No. 2
IEC60950_1F - ATTACHMENT
Clause Requirement + Test Result - Remark Verdict
ZB ANNEX (normative)
SPECIAL NATIONAL CONDITIONS (EN)
Clause Requirement + Test Result - Remark Verdict
5.1.7.1 In Finland, Norway and Sweden TOUCH N/A
CURRENT measurement results exceeding 3,5
mA r.m.s. are permitted only for the following
equipment:
• STATIONARY PLUGGABLE EQUIPMENT
TYPE A that
is intended to be used in a RESTRICTED
ACCESS LOCATION where equipotential
bonding has been applied, for example, in a
telecommunication centre; and
has provision for a permanently connected
PROTECTIVE EARTHING CONDUCTOR; and
is provided with instructions for the
installation of that conductor by a SERVICE
PERSON;
• STATIONARY PLUGGABLE EQUIPMENT
TYPE B;
• STATIONARY PERMANENTLY CONNECTED
EQUIPMENT.
6.1.2.1 In Finland, Norway and Sweden, add the N/A
(A1:2010) following text between the first and second
paragraph of the compliance clause:
If this insulation is solid, including insulation
forming part of a component, it shall at least
consist of either
- two layers of thin sheet material, each of
which shall pass the electric strength test below,
or
- one layer having a distance through
insulation of at least 0,4 mm, which shall pass the
electric strength test below.
Alternatively for components, there is no distance
through insulation requirements for the insulation
consisting of an insulating compound completely
filling the casing, so that CLEARANCES and
CREEPAGE DISTANCES do not exist, if the
component passes the electric strength test in
accordance with the compliance clause below
and in addition
- passes the tests and inspection criteria of
2.10.11 with an electric strength test of 1,5 kV
multiplied by 1,6 (the electric strength test of
2.10.10 shall be performed using 1,5 kV), and
- is subject to ROUTINE TESTING for
electric strength during manufacturing, using a
test voltage of 1,5 kV.
Page 18 of 19
Report No.: 085-110044304-000
Attachment No. 2
IEC60950_1F - ATTACHMENT
Clause Requirement + Test Result - Remark Verdict
ZB ANNEX (normative)
SPECIAL NATIONAL CONDITIONS (EN)
Clause Requirement + Test Result - Remark Verdict
It is permitted to bridge this insulation with an N/A
optocoupler complying with 2.10.5.4 b).
Annex ZD
(informative)
RF1
10ohm 1W
D3
D1
D4
D2
C1
L1
R2
L2
optional
R10
C2
R9
R8
C7
optional
R12
1
R11
C6
R7
U1
R5
R1
5
D6
C4
R4
R3
D5
1
4
3
T1
Tb
Ta
R13
D7
C9
C7
R14
optional
L3
C8
V+
V-
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Page 2 of 2
Report No.: 085-110044304-000
Attachment No. 3
PCB layout drawing:
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Page 1 of 8
Report Ref. No.: 085-110044304-000
Attachment No. 4
Contains
Cover page 1 page
Total: 8 pages
Page 2 of 8
Report Ref. No.: 085-110044304-000
Attachment No. 4
Additional test for adaptor with UK plug need to comply with IEC60950-1
(CB bulletin, IEC60950-1:2005+A1:2009, clause 4.3.6)
Page 1 of 3
Report No.: 085-110044304-000
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Attachment No. 5
Page 2 of 3
Report No.: 085-110044304-000
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Attachment No. 5
Page 3 of 3
Report No.: 085-110044304-000
-End-
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Photo documentation Page 1 of 11 Report No.: 085-110044304-000
Attachment No. 6
Details of:
General view for models SCFxxxyyyyE1mn
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Photo documentation Page 2 of 11 Report No.: 085-110044304-000
Attachment No. 6
Details of: General view for models SCFxxxyyyyE1mn
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Photo documentation Page 3 of 11 Report No.: 085-110044304-000
Attachment No. 6
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Photo documentation Page 4 of 11 Report No.: 085-110044304-000
Attachment No. 6
Details of: Components on PCB (Add glue to additionally fix the output wires with PCB)
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Photo documentation Page 5 of 11 Report No.: 085-110044304-000
Attachment No. 6
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Photo documentation Page 6 of 11 Report No.: 085-110044304-000
Attachment No. 6
Details of: Internal construction for models SCFxxxyyyyG1mn(after remove the top enclosure)
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Photo documentation Page 7 of 11 Report No.: 085-110044304-000
Attachment No. 6
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Photo documentation Page 8 of 11 Report No.: 085-110044304-000
Attachment No. 6
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Photo documentation Page 9 of 11 Report No.: 085-110044304-000
Attachment No. 6
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Photo documentation Page 10 of 11 Report No.: 085-110044304-000
Attachment No. 6
Details of: T1 general view after detach the plastic material (for support transformer secondary pins)
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch
Photo documentation Page 11 of 11 Report No.: 085-110044304-000
Attachment No. 6
---END---
TÜV SÜD Certification and Testing (China) Co., Ltd. Guangzhou Branch