Sony Cdxgt170 Manual

CDX-GT170/GT170S/
GT270/GT270S
SERVICE MANUAL E Model
CDX-GT170/GT170S/GT270/GT270S
Ver. 1.0 2007. 08 Chinese Model
CDX-GT270
(Photo: CDX-GT170)
• The tuner and CD sections have no adjustments. Model Name Using Similar Mechanism CDX-GT370/GT370S
CD Drive Mechanism Type MG-101TC-188//C
Optical Pick-up Name DAX-25A
SPECIFICATIONS
CD player section MW
Signal-to-noise ratio 120 dB Tuning range 531 – 1,602 kHz (at 9 kHz step)
Frequency response 10 – 20,000 Hz 530 – 1,710 kHz (at 10 kHz step)
Wow and flutter Below measurable limit MW tuning interval 9 kHz/10 kHz switchable
Antenna terminal External antenna connector
Tuner section Intermediate frequency 10.7 MHz/450 kHz
FM Sensitivity 30 µV
Tuning range 87.5 – 108.0 MHz (at 50 kHz step)
87.5 – 107.9 MHz (at 200 kHz step) SW
FM tuning interval 50 kHz/200 kHz switchable Tuning range SW1: 2,940 – 7,735 kHz
Antenna terminal External antenna connector SW2: 9,500 – 18,135 kHz
Intermediate frequency 10.7 MHz/450 kHz (except for 10,140 – 11,575 kHz)
Usable sensitivity 9 dBf Antenna terminal External antenna connector
Selectivity 75 dB at 400 kHz Intermediate frequency 10.7 MHz/450 kHz
Signal-to-noise ratio 67 dB (stereo), 69 dB (mono) Sensitivity 30 µV
Harmonic distortion at 1 kHz
0.5% (stereo), 0.3% (mono) – Continued on next page –
Separation 35 dB at 1 kHz
Frequency response 30 – 15,000 Hz
FM/MW/SW COMPACT DISC PLAYER

9-887-818-01 Sony Corporation
2007H04-1 eVehicle Division
© 2007. 08 Published by Sony Techno Create Corporation
Power amplifier section Notes on Chip Component Replacement

Outputs Speaker outputs (sure seal connectors) • Never reuse a disconnected chip component.
Speaker impedance 4 – 8 ohms • Notice that the minus side of a tantalum capacitor may be damaged
Maximum power output
by heat.
52 W × 4 (at 4 ohms)
General TEST DISCS

Output Audio outputs terminal Please use the following test discs for the check on the CD section.
(sub/rear switchable)
Power antenna (aerial) relay control terminal YDES-18 (Part No. 3-702-101-01)
Power amplifier control terminal PATD-012 (Part No. 4-225-203-01)
Inputs Antenna (aerial) input terminal
AUX input jack (stereo mini jack)
Tone controls Low: ±10 dB at 60 Hz (XPLOD)
Mid: ±10 dB at 1 kHz (XPLOD) CAUTION
High: ±10 dB at 10 kHz (XPLOD) Use of controls or adjustments or performance of procedures
Loudness +4 dB at 100 Hz other than those specified herein may result in hazardous
+2 dB at 10 kHz radiation exposure.
Power requirements 12 V DC car battery (negative ground)
Dimensions Approx. 178 × 50 × 179 mm
(7 1/8 × 2 × 7 1/8 in.) (w/h/d)
Mounting dimensions Approx. 182 × 53 × 162 mm If the optical pick-up block is defective, please replace the whole
(7 1/4 × 2 1/8 × 6 1/2 in.) (w/h/d) optical pick-up block.
Mass Approx. 1.2 kg (2 lb. 11 oz.) Never turn the semi-fixed resistor located at the side of optical pick-
Supplied accessories Parts for installation and connections (1 set) up block.
Card remote commander: RM-X151
(CDX-GT270/GT270S only) optical pick-up
MPEG Layer-3 audio coding technology and

patents licensed from Fraunhofer IIS and Thomson.
Design and specifications are subject to change without

notice.
SERVICE NOTES
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK

OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
breakdown because of the potential difference generated by the
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care. semi-fixed resistor
NOTES ON LASER DIODE EMISSION CHECK

The laser beam on this model is concentrated so as to be focused on
the disc reflective surface by the objective lens in the optical pick-
up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE

WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS
WHOSE PART NUMBERS APPEAR AS SHOWN IN THIS
MANUAL OR IN SUPPLEMENTS PUBLISHED BY SONY.
2
This compact disc player is classified as a CLASS 1 LASER TABLE OF CONTENTS

product. The CLASS 1 LASER PRODUCT label is located on the
exterior. 1. SERVICE NOTE ........................................................ 4
• E model 2. GENERAL
Location of Controls ........................................................ 5
Connections ..................................................................... 5
3. DISASSEMBLY
3-1. Sub Panel Assy ................................................................ 8
This label is located on the bottom of the chassis. 3-2. CD Mechanism Block ..................................................... 8
3-3. Main Board ...................................................................... 9
• Chinese model 3-4. Servo Board ..................................................................... 9
3-5. Chassis (T) Sub Assy ....................................................... 10
3-6. Roller Arm Assy .............................................................. 10
3-7. Chassis (OP) Assy ........................................................... 11
3-8. Chucking Arm Sub Assy ................................................. 11
3-9. Sled Motor Assy .............................................................. 12
3-10. Optical Pick-up Section ................................................... 13
3-11. Optical Pick-up ................................................................ 13
• CD Playback
You can play CD-DA (also containing CD TEXT) and CD-R/ 4. DIAGNOSIS FUNCTION ........................................ 14
CD-RW (MP3/WMA files*).
5. DIAGRAMS
Type of discs Label on the disc 5-1. Block Diagram –Main Section– ...................................... 17
5-2. Block Diagram –Display Section– .................................. 18
5-3. Printed Wiring Board –Main Section– ............................ 19
5-4. Schematic Diagram –Main Section (1/4)– ...................... 20
CD-DA 5-5. Schematic Diagram –Main Section (2/4)– ...................... 21
5-8. Printed Wiring Board –Key Section– .............................. 24
5-9. Schematic Diagram –Key Section– ................................. 25
MP3*
6. EXPLODED VIEWS
WMA* 6-1. Main Section .................................................................... 29
6-2. Front Panel Section ......................................................... 30
6-3. CD Mechanism Section (MG-101TC-188//C) ................ 31
7. ELECTRICAL PARTS LIST .................................. 32

* CDX-GT270/GT270S only
• UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK

Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
3
SECTION 1
SERVICE NOTE
EXTENSION CABLE AND SERVICE POSITION
When repairing or servicing this set, connect the jig (extension cable)
as shown below.
• Connect the MAIN board (CNP301) and the SERVO board (CN2)
with the extension cable (Part No. J-2502-076-1).
MAIN BOARD
CNP301 J-2502-076-1
SERVO BOARD
CN2
NOTE FOR REPLACEMENT OF THE SERVO BOARD

When repairing, the complete SERVO board (A-1201-631-A) should
be replaced since any parts in the SERVO board cannot be repaired.
NOTE FOR REPLACEMENT OF THE AUX JACK (J901)

To replace the AUX jack requires alignment.
1. Insert the AUX jack into the KEY board.
2. Place the KEY board on the front panel.
3. Solder the three terminals of the jack.
KEY board
AUX jack
front panel
4
SECTION 2
GENERAL This section is extracted
from instruction manual.
• LOCATION OF CONTROL
Location of controls and basic operations

Main unit J DSPL (display)/SCRL (scroll) button The following buttons on the card remote
(CDX-GT370S/GT370/GT270S/GT270) commander have also different buttons/functions
12 3 4 5 6 78 page 8 from the unit. Remove the insulation film before
To change display items (press); scroll the use (page 5) (CDX-GT370S/GT370/GT270S/
display item (press and hold). GT270 only).
OFF DSPL (display) button (CDX-GT170S/ qk < (.)/, (>) buttons
PUSH SELECT
GT170) page 8 To control CD/radio, the same as (SEEK)
EQ3 SOURCE
AUX
To change display items. –/+ on the unit.
SEEK SEEK
Setup, sound setting, etc., can be operated by
K SEEK –/+ buttons < ,.
DSPL MODE CD:
REP SHUF PAUSE
To skip tracks (press); skip tracks ql DSPL (display) button
BTM 1 2 3 4 5 6
continuously (press, then press again within To change display items.
about 1 second and hold); reverse/fast-
forward a track (press and hold). w; VOL (volume) +/– button
To adjust volume.
9 q; qa qs qd qf qg qh qj Radio:
To tune in stations automatically (press); find wa ATT (attenuate) button
a station manually (press and hold). To attenuate the sound. To cancel, press
Card remote commander This section contains instructions on the location L MODE button page 8 again.
of controls and basic operations.
RM-X151 (CDX-GT370S/GT370/ For details, see the respective pages.
To select the radio band (FM/MW/SW)*. ws SEL (select) button
GT270S/GT270 only) For optional device (CD/MD changer, etc.,) M BTM button page 8 The same as the select button on the unit.
operation, see “Using optional equipment” on To start the BTM function (press and hold). wd M (+)/m (–) buttons
page 10. The corresponding buttons on the card
1 wa remote commander control the same functions as N RESET button (located behind the front To control CD, the same as (1)/(2)
OFF ATT
panel) (CDX-GT370S/GT370 only) (ALBUM –/+) on the unit.
4 ws those on the unit.
page 5 Setup, sound setting, etc., can be operated by
SOURCE SEL MODE
A OFF button M m.
qk qs To power off; stop the source. O Frequency select switch (located on the wf SCRL (scroll) button
bottom of the unit)
+ B EQ3 (equalizer) button page 9 To scroll the display item.
See “Frequency select switch” in the
wd To select an equalizer type (XPLOD,
VOCAL, EDGE, CRUISE, SPACE,
supplied installation/connections manual. wg Number buttons
– To receive stored stations (press); store
GRAVITY, CUSTOM or OFF). P Number buttons stations (press and hold).
ql DSPL SCRL wf C Volume control dial/select button CD:
(1)/(2): ALBUM –/+ (during MP3/WMA * In the case of a CD/MD changer being connected;
1 2 3 page 9 playback) (CDX-GT370S/GT370/ when (SOURCE) is pressed, the connected device
4 5 6
wg To adjust volume (rotate); select setup items GT270S/GT270) (“MD”) will appear in the display, depending on
(press and rotate). which device is connected. Furthermore, if (MODE)
To skip albums (press); skip albums is pressed, you can switch the changer (CDX-
+ D SOURCE button continuously (press and hold). GT370S/GT370 only).
w; VOL
– To power on; change the source* (Radio/CD/ (3): REP page 8
Note
AUX). (4): SHUF page 8 If the unit is turned off and the display disappears, it
(6): PAUSE cannot be operated with the card remote commander
E Disc slot To pause playback of a CD on this unit. unless (SOURCE) on the unit is pressed, or a disc is
Insert the disc (label side up), playback To cancel, press again. inserted to activate the unit first.
starts. Radio:
To receive stored stations (press); store
F Display window stations (press and hold).
G AUX input jack page 10 Q Receptor for the card remote
To connect a portable audio device. commander (CDX-GT370S/GT370/
H Z (eject) button GT270S/GT270 only)
To eject the disc.
I (front panel release) button page 5
6 7
• CONNECTIONS
Connection example
Notes (2-A)
A • Be sure to connect the ground (earth) lead before connecting
the amplifier.
• The alarm will only sound if the built-in amplifier is used.
AUDIO OUT REAR*

Ejemplo de conexiones
Notas (2-A)
• Asegúrese de conectar primero el cable de conexión a masa
antes de realizar la conexión del amplificador.
• La alarma sonará únicamente si se utiliza el amplificador
incorporado.
* AUDIO OUT SUB/REAR
AUDIO OUT REAR*
* AUDIO OUT SUB/REAR
B CDX-GT370S/GT370
BUS AUDIO IN
BUS CONTROL IN
5
CDX-GT370S/GT370 *1 CDX-GT370S/GT370 only

*2 RCA pin cord (not supplied)
*3 AUDIO OUT can be switched SUB or REAR.
For details, see the supplied Operating
Instructions.
*1 Solo CDX-GT370S/GT370
*2 Cable con terminales RCA (no suministrado)
Supplied with the CD/MD changer *3 AUDIO OUT (salida de audio) puede
Suministrado con el cambiador de CD/MD cambiarse a SUB (secundaria) o REAR
(posterior). Para obtener información,
consulte el manual de instrucciones
*2 suministrado.
*1
CDX-GT370S/GT370
BUS AUDIO IN*1 L
BUS REAR FRONT

from car antenna (aerial) IN AUDIO OUT
desde la antena del automóvil

AUDIO OUT BUS
Fuse (10 A)
REAR*3 Fusible (10 A) CONTROL IN*1
Blue/white striped 2
Con rayas azules y blancas
AMP REM
3 Max. supply current 0.3 A
Corriente máx. de alimentación de 0,3 A
White Black
Blanco Negro
Left
Izquierdo
White/black striped
1
Con rayas blancas y negras
Blue
Gray
Azul
Gris
Right ANT REM
Derecho Gray/black striped Max. supply current 0.1 A
2
Con rayas grises y negras Corriente máx. de alimentación de 0,1 A
Red
Green
Rojo
Verde
Left
Izquierdo
Green/black striped 4
Con rayas verdes y negras
Purple Yellow
Morado Amarillo
Right
Derecho
Purple/black striped
5
Con rayas moradas y negras
Connection diagram Diagrama de conexión

1 To a metal surface of the car 1 A una superficie metálica del automóvil
First connect the black ground (earth) lead, then connect the Conecte primero el cable de conexión a masa negro, y
yellow, and red power supply leads. después los cables amarillo y rojo de fuente de alimentación.
2 To the power antenna (aerial) control lead or 2 Al cable de control de la antena motorizada
power supply lead of antenna (aerial) booster o al cable de fuente de alimentación del
amplifier amplificador de señal de la antena
Notes Notas
• It is not necessary to connect this lead if there is no power • Si no se dispone de antena motorizada ni de amplificador
antenna (aerial) or antenna (aerial) booster, or with a de antena, o se utiliza una antena telescópica accionada
manually-operated telescopic antenna (aerial). manualmente, no será necesario conectar este cable.
• When your car has a built-in FM/MW/SWantenna (aerial) • Si el automóvil incorpora una antena de FM/MW/SW en el
in the rear/side glass, see “Notes on the control and power cristal trasero o lateral, consulte “Notas sobre los cables
supply leads.” de control y de fuente de alimentación”.
3 To AMP REMOTE IN of an optional power 3 A AMP REMOTE IN de un amplificador de
amplifier potencia opcional
This connection is only for amplifiers. Connecting any other Esta conexión es sólo para amplificadores. La conexión de
system may damage the unit. cualquier otro sistema puede dañar la unidad.
4 To the +12 V power terminal which is 4 Al terminal de alimentación de +12 V que
energized in the accessory position of the recibe energía en la posición de accesorio
ignition key switch del interruptor de encendido
Notes Notas
• If there is no accessory position, connect to the +12 V • Si no hay posición de accesorio, conéctelo al terminal de
power (battery) terminal which is energized at all times. alimentación (batería) de +12 V que recibe energía sin
Be sure to connect the black ground (earth) lead to a interrupción.
metal surface of the car first. Asegúrese de conectar primero el cable de conexión a
• When your car has a built-in FM/MW/SW antenna (aerial) masa negro a una superficie metálica del automóvil.
in the rear/side glass, see “Notes on the control and power • Si el automóvil incorpora una antena de FM/MW/SW en el
supply leads.” cristal trasero o lateral, consulte “Notas sobre los cables
5 To the +12 V power terminal which is de control y de fuente de alimentación”.
energized at all times 5 Al terminal de alimentación de +12 V que
Be sure to connect the black ground (earth) lead to a metal recibe energía sin interrupción
surface of the car first. Asegúrese de conectar primero el cable de conexión a masa
Notes on the control and power supply leads negro a una superficie metálica del automóvil.
• The power antenna (aerial) control lead (blue) supplies +12 V Notas sobre los cables de control y de fuente de
DC when you turn on the tuner. alimentación
• When your car has built-in FM/MW/SW antenna (aerial) in the • El cable de control de la antena motorizada (azul) suministrará
rear/side glass, connect the power antenna (aerial) control cc de + 12 V cuando conecte la alimentación del sintonizador.
lead (blue) or the accessory power supply lead (red) to the • Si el automóvil dispone de una antena de FM/MW/SW
power terminal of the existing antenna (aerial) booster. For incorporada en el cristal trasero o lateral, conecte el cable
details, consult your dealer. de control de antena motorizada (azul) o el cable de fuente
• A power antenna (aerial) without a relay box cannot be used de alimentación auxiliar (rojo) al terminal de alimentación
with this unit. del amplificador de antena existente. Para obtener más
Memory hold connection información, consulte a su distribuidor.
When the yellow power input lead is connected, power will • Con esta unidad no es posible utilizar una antena motorizada
always be supplied to the memory circuit even when the ignition sin caja de relé.
switch is turned off. Conexión para protección de la memoria
Notes on speaker connection Si conecta el cable de fuente de alimentación amarillo, el circuito
• Before connecting the speakers, turn the unit off. de la memoria recibirá siempre alimentación, aunque apague el
• Use speakers with an impedance of 4 to 8 ohms, and with interruptor de encendido.
adequate power handling capacities to avoid its damage. Notas sobre la conexión de los altavoces
• Do not connect the speaker terminals to the car chassis, or • Antes de conectar los altavoces, desconecte la alimentación
connect the terminals of the right speakers with those of the de la unidad.
left speaker. • Utilice altavoces con una impedancia de 4 a 8 Ω con la
• Do not connect the ground (earth) lead of this unit to the capacidad de potencia adecuada para evitar que se dañen.
negative (–) terminal of the speaker. • No conecte los terminales de altavoz al chasis del automóvil,
• Do not attempt to connect the speakers in parallel. ni conecte los terminales del altavoz derecho con los del
• Connect only passive speakers. Connecting active speakers izquierdo.
(with built-in amplifiers) to the speaker terminals may damage • No conecte el cable de conexión a masa de esta unidad al
the unit. terminal negativo (–) del altavoz.
• To avoid a malfunction, do not use the built-in speaker leads • No intente conectar los altavoces en paralelo.
installed in your car if the unit shares a common negative (–) • Conecte solamente altavoces pasivos. Si conecta altavoces
lead for the right and left speakers. activos (con amplificadores incorporados) a los terminales de
• Do not connect the unit’s speaker leads to each other. altavoz, puede dañar la unidad.
Note on connection • Para evitar fallas de funcionamiento, no utilice los cables de
If speaker and amplifier are not connected correctly, “FAILURE” altavoz incorporados instalados en el automóvil si la unidad
appears in the display. In this case, make sure the speaker and comparte un cable negativo común (–) para los altavoces
amplifier are connected correctly. derecho e izquierdo.
• No conecte los cables de altavoz de la unidad entre sí.
Nota sobre la conexión
Si el altavoz no está conectado correctamente, aparecerá
“FAILURE” en la pantalla. Si es así, compruebe la conexión del
altavoz.
6
SECTION 3
DISASSEMBLY
Note: This set can be disassemble according to the following sequence.
SET
3-1. SUB PANEL ASSY

(Page 8)
3-2. CD MECHANISM BLOCK

(Page 8)
3-3. MAIN BOARD 3-4. SERVO BOARD

(Page 9) (Page 9)
3-5. CHASSIS (T) SUB ASSY

(Page 10)
3-6. ROLLER ARM ASSY

(Page 10)
3-7. CHASSIS (OP) ASSY

(Page 11)
3-8. CHUCKING ARM SUB ASSY

(Page 11)
3-9. SLED MOTOR ASSY

(Page 12)
3-10. OPTICAL PICK-UP SECTION

(Page 13)
3-11. OPTICAL PICK-UP

(Page 13)
7
Note: Follow the disassembly procedure in the numerical order given.
3-1. SUB PANEL ASSY
3 two claws
2 two claws
1 two screws
(+PTT 2.6 × 6)
4 sub panel assy
3-2. CD MECHANISM BLOCK
6 bracket (CD)
7 CD mechanism block
5 two screws
(+PTT 2.6 × 4)
3
2 screw
(+PTT 2.6 × 6)
4 CNP301
1 screw
(+PTT 2.6 × 6)
8
3-3. MAIN BOARD
2 two screws
(+PTT 2.6 × 8)
4 two screws
(+P 2.6 × 8) 5 two screws
(+PTT 2.6 × 10)
1 three ground point screws 6 screw
(+PTT 2.6 × 6) (+P 2.6 × 10)
7 screw
(+PTT 2.6 × 8)
8 heat sink
9 MAIN board
3 insulating sheet
3-4. SERVO BOARD
WHT
RED
BLK
WHT 2 toothed lock screw

RED (M 1.7 × 2.5)
BLK
RED
ORG 3 toothed lock screw
BLE (M 1.7 × 2.5)
YEL SERVO board
GRY
1 Remove the eleven solders. 5 SERVO board
4 optical pick-up (16 core)

(CN1)
claw
claw
9
3-5. CHASSIS (T) SUB ASSY
2 two precision screws

1 two precision screws (+P 1.7 × 2.2)
(+P 1.7 × 2.2)
4 chassis (T) sub assy
3 claw
3-6. ROLLER ARM ASSY
5 roller arm assy
4 gear (RA1)
1 spring (RAL)
3 washer
2 spring (RAR)
10
3-7. CHASSIS (OP) ASSY
6 chassis (OP) assy
1 tension spring (KF)

5
7 coil spring (damper) (natural)
8 coil spring (damper) (black)

4 slider (R)
3 lever (D)
2 gear (LE1)
3-8. CHUCKING ARM SUB ASSY
3 chucking arm sub assy
1 spring
Note: Have this portion receive the chassis. Note: Have this portion receive the chassis.
Note: Be careful not to touch the turn table.
11
3-9. SLED MOTOR ASSY
2 three serration screws

(M 2 × 3)
3 sled motor assy
1 spring
turn table spring
stand
Note:
Never remove these parts since they were adjusted.
stand
Note: Place the stand with care not to touch the turn table.
Note for Assembly
three serration screws

(M 2 × 3)
sled motor assy
Note: Take care to prevent the chassis from being bent

when tightening the three machine screws.
12
3-10. OPTICAL PICK-UP SECTION
2 optical pick-up section
Note: Be careful not to touch the lens and hologram

terminal when removing the optical pick-up section.
3-11. OPTICAL PICK-UP
1 pan tapping screw

(M 1.4 × 2.5)
2 leaf spring (sub guide)
3 leaf spring (OP)
5 optical pick-up
4 lead screw assy
Notes for Assembly
Prevent the end of the Prevent the end of the There is space at the end of the
leaf spring (sub guide) from being leaf spring (sub guide) from being leaf spring (sub guide) to avoid
in contact with the OP slide base. in contact with the OP slide base. contact with the slide.
13
SECTION 4
DIAGNOSIS FUNCTION
Description of the Diagnostics function: 4. Contents of each display mode
4-1. Reset count display mode
1. Setting the Diag display mode
With the power off, press the [4] button, [5] button, and [4] button
01 XX
on the set body or the remote control (for more than 2 seconds)
in turn. Reset count
(in hexadecimal format)
2. Canceling the Diag display mode Diag code
During the Diag function mode, press the [OFF] button. 01: Reset count
3. Initial display in the Diag display mode.

Just when the Diag mode is entered, “reset count” is displayed. 4-2. Reset count by watchdog timer display mode
The display mode is switched by each rotation of
M >/SEEK + or . m/SEEK – keys. 02 XX
Reset count
Reset count display
Diag code
02: Number of resets by watchdog timer
01 XX
4-3. Number of connected units display mode

Reset count by watchdog timer display
031 XXX
02 XX
Show the number of connected units for
CD-C, MD-C and XM respectively from
Number of connected units display the rightmost (in hexadecimal format).
Recency of information
031 XXX 1-3: 1 represents the latest.
Diag code
03: Number of connected unit.
Operating hours display
The display mode is switched by each rotation of [2] or [1] keys
04 XXXX during the number of connected units display mode.
CD error information display

No. of connected units history 1 (latest) display
051 XX
031 XXX
OFFSET/FAILURE error display

No. of connected units history 2 display
061XXXXX
032 XXX
No. of connected units history 3 display
033 XXX
4-4. Operating hours display mode
04 XXXX
Operating hours
Diag code
04: Operating hours
14
4-5. CD error information display mode 4-6. OFFSET/FAILURE error display mode
4-5-1. Error description
061XXXXX
051 XX
Error information Operating hours
Error description Indication Description Error description
(in hexadecimal (0: OFFSET, 1: FAILURE)
1X SERVO ERROR
format)
3X LOADING ERROR Recency of information
Recency of information 1-3: 1 represents the latest.
1-3: 1 represents the latest. 4X TRACK JUMP
5X TEXT ERROR Diag code
Diag code 06: OFFSET/FAILURE
05: CD error information FX MECHA ERROR
The display mode is switched by each rotation of [2] or [1] keys

4-5-2. Disc type and operating hours during the OFFSET/FAILURE error display mode.
051XXXXX
Disc type OFFSET/FAILURE error history 1 (latest) display
Operating hours Indication Disc type
Disc type 0 MP3 061XXXXX
Recency of information 1 WMA
1-3: 1 represents the latest. 2 AAC
Diag code OFFSET/FAILURE error history 2 display
3 ATRAC
05: CD error information 8 CD/DA
F UNKNOWN 062XXXXX
The display mode is switched by each rotation of [2] or [1] keys OFFSET/FAILURE error history 3 display
during the CD error information display mode.
063XXXXX
CD error info history 1 (latest)
Error description plus error details display
051 XX
CD error info history 1 (latest)

Disc type plus operating hours display
051XXXXX
CD error info history 2

052 XX

052XXXXX

053 XX

053XXXXX
15
MEMO
16
SECTION 5
DIAGRAMS
5-1. BLOCK DIAGRAM — MAIN SECTION —
ELECTRONIC VOLUME
IC401
J330
SUBOUT L 21 L AUDIO
SUBOUT R 22 R-CH OUT
I2C BUS CONTROLLED R-CH R REAR
POWER AMP/MULTIPLE
MUTE VOLTAGE REGULATOR
J901 R-CH Q481 IC750
9 AUX-LCH CN601
AUX
R-CH 7 AUX-RCH 1
OUT-FL 25 12 IN-FL OUT-FL+ 5 FL+
9
OUT-FL– 3 FL–
OUT-RL 23 11 IN-RL
TU1 8 AUX GND 2
(TUNER UNIT) OUT-RL+ 9 RL+
10
OUT-FR 26 R-CH (FRONT) OUT-RL– 7 RL–
MUTE MUTE
J1 OUT-RR 24 R-CH (REAR) Q441 Q461
1 ANT L-CH 4 4 TU-LCH
(ANTENNA) VOLATT
R-CH 3 R-CH R-CH 3 TU-RCH MUTE 28
4
I2C-SCL FR+
SCL 29 12
I2C-SDA R-CH FR–
SDA 30 R-CH 3
RR+
6 CD-LCH MUTE D479 11
CONTROL SWITCH RR–
R-CH 5 CD-RCH BATT
Q478,479
5
AMP-REM 29 AMP-REM
I2C-SCL I2C-SCL
TU-SCL 13 4 SCL
I2C-SDA I2C-SDA 6
TU-SDA 14 2 SDA ANT-REM 27 ANT-REM
AUDIO +8.3V 10 VCC (+8.3V) SYSTEM CONTROL
BATT FU601
11 TU-VDD (TU+5V) IC501 (1/2) 16
TU+5V VP 35 BATT
B.U +3.3V 15 E2P-VDD
I2C-SCL VP1 20
QUALITY I2C_CKO 33 D511
QUALITY 5 38 QUALITY I2C-SDA VP2 6
VSM I2C_SIO 34
S-METER 6 39 VSM
TUATT
TU-MUTE 7 12 TU ATT
VOL ATT 9 B.UP+B 37 B.U+3.3V
EEP-SCL
E2P-SCL 16 25 EEP_CKO
EEP-SDA ATT 86 BU +3.3V
E2P-SDA 17 24 EEP_SIO
AUDIO+8.3V 30 AUDIO +8.3V
BEEP 5 16 BEEP SERVO+3.3V 31 SERVO+3.3V
AMPSTB 26 22 STB MECHA+6V 33 MECHA+6V
DIAG 8 25 DIAG PANEL+B 34 PANEL+B
ACCESSORY CHECK 7
ACC_IN 72 Q631 ACC
D580
CNP301 BATTERY LEVEL CHECK BATT
BU IN 54 TU+5V REG
Q580–582 TU+5V AUDIO +8.3V
11 AU_LCH Q1,D1
15 AU_RCH D581
R-CH
D512
22 UNI_SO
59 UNISO
24 UNI_SI
58 UNISI
26 UNI_CLK
60 UNISCK
16 Z_MUTE
93 Z-MUTE • R-CH is omitted due to same as L-CH.
5 CD_ON • Signal Path
CD 98 CD_ON
MECHANISM 7 CDM_ON
99 CDM_ON : CD PLAY
UNIT D510
(MG-101TC) 6 SYS_RST : FM
77 RESET
21 EJECT_OK : MW/SW
BU+3.3V 88 SYSRST
27 BUS_ON
87 BUSON : AUX
9 A_ATT
25 BU_IN
18 D_+3.3V
SERVO +3.3V RESET
19 A_+3.3V IC602
8 BU_+3.3V
BU_+3.3V
1,2 DR_+6V 1 VOUT VDD 2 BU +3.3V
MECHA +6V
17 17
5-2. BLOCK DIAGRAM — DISPLAY SECTION — • NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
THIS NOTE IS COMMON FOR PRINTED WIRING

BOARDS AND SCHEMATIC DIAGRAMS.
SYSTEM CONTROL DISPLAY CONTROL (In addition to this, the necessary note is
IC501 (2/2) IC901
printed in each block.)
KEY MATRIX 40 KEYIN1 For schematic diagrams. For printed wiring boards.
LSW901–911, Note: Note:
S901–904 41 KEYIN0 3 • All capacitors are in µF unless otherwise noted. (p: pF) • X : parts extracted from the component side.
S1 | LCD901
LCD_SO 28 48 DI
| 34
50 WV or less are not indicated except for electrolytics • Y : parts extracted from the conductor side.
D503 LCD_CKO 29 47 CL S33
39
• LIQUID and tantalums. • a : Through hole.
LCD_CE 27 46 CE CRYSTAL
DISPLAY
• All resistors are in Ω and 1/4 W or less unless otherwise • : Pattern from the side which enables seeing.
COM1 35
KEY ACKNOWLEDGE | | PANEL specified. (The other layers' patterns are not indicated.)
BACK LIGHT
SWITCH 52 KEY ACK COM4 38 • f : internal component.
DIMMER
Q664 • C : panel designation. Caution:
Pattern face side: Parts on the pattern face side seen from the
76 AD_ON
Note: The components identified by mark 0 or dotted line (Side B) pattern face are indicated.
1 2 with mark 0 are critical for safety. Parts face side: Parts on the parts face side seen from the
RE901 PANEL+B Replace only with part number specified. (Side A) parts face are indicated.
PUSH SELECT LED931
(VOLUME)
• A : B+ Line.
( LCD BACK
LIGHT ) LSW901–911,
LED941,942,
• B : B– Line.
C
ROTARY RE-0 944,945,951–953
• H : adjustment for repair.
ENCODER 31 RE-IN0
RE-1 KEY • Voltages and waveforms are dc with respect to ground Q
32 RE-IN1 ( ILLUMINATE ) under no-signal (detuned) conditions.
These are omitted
no mark : FM B E
( ) : AM/MW/SW
79 XOUT
X502 < > : CD PLAY
32.768kHz DIMMER
80 XIN SWITCH ∗ : Impossible to measure
Q931 • Voltages are taken with a VOM (Input impedance 10 MΩ).
82 OSCIN Voltage variations may be noted due to normal production BE C
X501
tolerances.
18.432MHz These are omitted
83 OSCOUT
LCD • Waveforms are taken with a oscilloscope.
BACK LIGHT Voltage variations may be noted due to normal production
SWITCH
BU+3.3V Q932
tolerances.
• Circled numbers refer to waveforms.
• Signal path. ECB
10K
S502 J : CD PLAY These are omitted
FREQUENCY 3 AREASEL2
SELECTOR 9K
F : FM
f : MW/SW
GT270/GT270S
L : AUX
REMOTE CONTROL
SIGNAL RECEIVER
IC971
7 NOSE_SW SIRCS 64 3 OUT IR
• Waveforms
— MAIN Board —
1 IC501 ul (XOUT)
0.7Vp-p
32.768kHz
0.5 V/DIV, 20 µsec/DIV
2 IC501 id (OSCOUT)
1.8Vp-p
18.432MHz
0.5 V/DIV, 20 nsec/DIV
18 18
5-3. PRINTED WIRING BOARD — MAIN SECTION — : Uses unleaded solder.
1 2 3 4 5 6 7 8 9 10 11 12 13 14
J330
AUDIO OUT
A J1
REAR
(ANTENNA) L R
JC753
JC754
JC755
CN601
C454
YEL
C464
JW34
C775 C774
JW32
R472 FU601
B R482
C751 C771 IC750 C765
JW9
C764
R432 JW1
Q471 Q441 Q431
JW3 JW2
JW11
JW137
C763
JW12
JW10
JW13
JW138
JW14
R442 C753 C617
R471
C442 JW16
JW19 D617
JW22
C432
C
C601
JW15
Q481 C445
D756
D755
JW21
D757
C435 C618
JW7
JW6
JW4
JW8
D601
JW5
R441
D758
R431
C452 Q451 C623
R481 C441
YEL
C462
D753
D752
D754
D751
D761
C602
C622
(CHASSIS) C465 R452
D760
D759
C471
C455 R462 L601

R451 Q461
C451
D762
R461 JW35
D C770
C481
JW38
TU1
C750
JW31 • Semiconductor
JW26
C769
C461 JW39 Location
JW18
C431
JW23
JW88 JW111
Ref. No. Location
JW17
JW24
JW25
C412
C404 JW43 CD
JW92 D1 F-3
JW102
C758 MECHANISM
C405 C401 R401 CNP301 UNIT D153 I-2
JW42
C8 C413 C776 (MG-101TC)
JW93
JW27 D479 E-6
JW20
Q479
D502 H-7
E C756 R479 D479
JW55 D503 I-5
JW131
JW132
IC401 C754 R539

D510 G-8
C479
C4 JW98
JC681 D511 F-6
C343
C12 R412 R752 Q478
R1 JW95 C302 D512 H-8
C301
C13 R413 C755
D1 C308 D580 F-10
R414 JW96
JW94 JW106
C6 JW91 C310 R302 D581 F-10
JW30
JW66
JW29
JW97
R2
R583
C5 L1 JW129 C309 R301 JW115 D601 C-10
R3 D581
Q580 D617 C-9
F FB1 JW130 C407 C406
D704 I-3
R582
C312
R12 R557 S502 FB604
JW101 D511 R528 D719 I-4
JW89
FREQUENCY
JW28
JW99
R13 Q1 R531 D580
JW135
C7
SELECTOR R550 D751 D-7
JW117
JW127
R677 D752 D-7

JW45
JW124
JW114
JW100 9K
C305
C306
JW118
JW56
JW50
JW109
R5
JW90
R546 R524 D753 D-6
R9 R526 R572 D754 D-7
R631
R4 JW123 D755 C-6
JW120
R8 10K R537 R507
JW83 R527 R574 R675 D756 C-6
G JW80
R534
R506 R756
FMB3 R566
D510
R578 JW57
Q631
D757 C-6
JW40
R544 R532
C511
R634 D758 C-6
JW121 R676
C510 R632 D759 D-8
JW67
JW122 R509
D760 D-8
JW51
R633
JW69
C631
JW103
C503
JW48
JW59
D761 C-9
JW49
X501
JW72 C504 JW46

D762 D-9
R570
JW54
JW79
R511
R510 R512
JW78 R563 IC401 E-3
R664
C153
1
H C522 JW119
50
R155 R679 JC533 R547

R522 R662
IC
C523 C508 R636

IC501 H-6
R661
R151 C507 D512 R556 R541

IC602 I-9
R521
R663 X502 R543

C151 R540
JW44
C152 GT270/GT270S
R672 R601 IC750 B-6
C154
JW133
R153 R154 C513 D502 R519 JW75

R533 C519 Q581
JW73
C516 R674
JW71
JW76
C155 R529
JW108
JW70
JW74
L151 R152
R502 C512 JW65 Q1 F-2
JW87
R542 Q582
C501 R568 3 2
C514 Q431 C-4
R561
D153 D704 R692 JW82 R584

R504 R536 4 1
JW104
JW105
C509 IC602 Q441 C-4

R503 R585
R693
JW61 R505 FMB4 R535

R567
Q451 C-4
I JW142 JW139 R513 D503
JC504 R558 R517
Q664 R690 JW62 R673
Q461 D-4
JW141
JW140
D719 GT170/GT170S
JW77
JW68
R514 R565 JW63 JC510

R671
C550 Q471 C-3
11 Q478 E-6
(11)
Q479 E-6
1-874-377- Q481 C-3
(CHASSIS)
X501 Q580 F-10
CN701
Q581 H-10
Q582 I-10
J Q631 G-9
Q664 I-7
A
KEY BOARD CN901
(Page 24)
19 19
5-4. SCHEMATIC DIAGRAM — MAIN SECTION (1/4) — • Refer to page 26 for IC Block Diagrams.
J330
C464 C454
TU1
C431 R431
Q431
R432
C412
J1 IC401
R12
R13
R2
R3
C401
C413
Q451
C404 R452
C405 C451 R451
C7 C406
FB1
C407
C8 R8
R441
C441
Q441
C5 R442
C13 R9
C12 R413 R412

C4 R5 R4 R462 Q461
C461 R461
R414 (Page 21)
R1
C6 C481 R481
R401 R482 Q481
Q1
D1 IC B/D
R472 Q471
C471 R471
L1
(Page 22) (Page 23)
20 20
C775 C765 C764 C774
C751
D751
D752
C750
D753
IC B/D
D754
JC754
JC755 D755
D756
C435 C432
IC750 D757
D758
CN601
C455 C452
C445 C442
D759
D760
C465 C462
JC753
Q479 C753
D479
(Page 20) FU601
D617
R479 C754 C617 C618
C763
R752
C769
C755
D761
D762
Q478 C770
C479 C756
L601
JW111
C771
C602 C601 D601
C758
C776
(Page 22) (Page 23)
21 21
• Refer to page 18 for Waveforms.

5-6. SCHEMATIC DIAGRAM — MAIN SECTION (3/4) — • Refer to page 27 for IC Pin Description of IC501.
(Page 20) (Page 21)
D511
R531 R692 R693 R535 R558
R556 R533 R519
C310
R536
JC533
R674
D502
R679
C309 R672
R542
R547
R539 D512
R636
D510
C507 C509 R543

CNP301
R563
R578 R690 R568
R529
X502 R517
R302 C508
Q664
C343 C301 C308
C302 X501 R561
R565
R301
C312 D503
C510 R509
R567
R528 C514 JC504
C511 R566
R675 R505 R673

R676 R671 (Page 23)
C305 C306 R504
R503
IC501
C512 R502
R574 C501 C516

R572 C513
R527
R526
R677 C523
R524
C522
R661
R663
R522
R521
S502
R662
R511
R510
R546 C504 R664
R557
R534
R544
R507
R537
R550
R756
R506
R514
R512
C503
R513
R570
R532
JC510
C550
22 22
(Page 21) (Page 20)
JC681
FB604
C623 R155 C153 C151 C152

IC602
R153
D719 R154
R601
C622
L151 R151 R152
C519
C154
C155
CN701
Q631
R633 R631
(Page 22)
JW140
R634 C631 R632
(Page 25)
R541
R585
D153
D704
R540 Q581
R584 D580 R582
Q580 D581 R583

Q582
23 23
5-8. PRINTED WIRING BOARD — KEY SECTION — : Uses unleaded solder.
1 2 3 4 5 6 7 8 9 10 11 12 13 14
A
LED941,
LED942, LED942 LSW903 LED944, S901
S902 S902 M > S903
LED951–953 Z
LED941
LED931
OFF (RING ILLUMINATION) SEEK+ SOURCE (LCD BACK LIGHT) S901
R902
R943
B
R945
LED944
S903 LED943
LSW901
EQ3 LED951
LCD901
LSW901 LIQUID CRYSTAL DISPLAY PANEL
LED931
LSW904 LSW904 LSW903
R901
.m
SEEK–
C R948
R905
53
S904
52
LED945
LED9
LED9
R944
C971
LSW902 37 1 GT270/GT270S
R946
R975
DSPL/SCRL IC971
(GT270/GT270S) LSW902 IC971
DSPL LSW905 LSW906 LSW907 LSW908 LSW909 LSW910 LSW911 1 4
D (GT170/GT170S)
2 3
11
(11)
1-874-378-
LSW905 LED945, LSW906 LSW907 LSW908 LSW909 LSW910 LSW911
BTM S904 1/ALBUM– 2/ALBUM+ 3/REP 4/SHUF 5 6/PAUSE
MODE (GT270/GT270S) (GT270/GT270S)
1 2
(GT170/GT170S) (GT170/GT170S) (Page 19)
E MAIN BOARD CN701
R915
R951
R952
R913
R912 GT270/GT270S
R909
R914
F
R992
R950 D994
R910 R949 CN901

R911
R954 R953
R947
R977
R972 R908
3 4 5 R979
R984
R985
R986
D991
R988 R978
G R907 Q931 FB903
D992
D993
D998
R933
C987
C984
Q932
RE901 C983 R934 R932 J901
IC901
R971 R974 AUX
C981 D981 D903 R931
2 1 R982 R981
C986
R987 GT270/GT270S
D982
H
R904
R903
RE901
R942 R941
PUSH SELECT
(VOLUME)
11
1-874-378- (11)
• Semiconductor Location
Ref. No. Location Ref. No. Location Ref. No. Location
D903 G-11 IC901 G-8 LED945 C-4
D981 H-10 IC971 D-14 LED951 B-3
D982 H-10 LED952 C-4
D991 G-11 LED931 C-13 LED953 C-3
D992 G-11 LED941 B-13
D993 G-11 LED942 A-1 Q931 G-10
D994 F-14 LED944 B-4 Q932 G-10
24 24
5-9. SCHEMATIC DIAGRAM — KEY SECTION —
R931 LED941 R943 R949 R951 LED951

R945
R981
R932 R975
R982
LSW903(2/2) IC971
LSW905(2/2) LSW911(2/2)
R933 R941 R971
C971
LSW906(2/2)
LED931
R942 LSW901(2/2) LED944 R947 LSW908(2/2) LSW910(2/2) LED952
C981 C983 R984

Q931 R985
LSW902(2/2) LSW907(2/2) C984
D982
LSW904(2/2) IC901
LED943 LED945 LSW909(2/2) R953 LED953 R986
R987
R934
R977
D981
C986 C987 R988
R978
Q932 LED942 R944 R946 R948 R950 R952 R954 R972 R979
D998 R992
R974
CN901
D994
LCD901
RE901
R901 R902 R903 R904
R905
LSW902(1/2)
LSW901(1/2)
S901
(Page 23)
S902
S903
R907 R908 R909 R910 R911 R912 R913 R914 R915

D991
D992
D993
D903
J901
LSW903(1/2)
LSW904(1/2)
LSW905(1/2)
LSW906(1/2)
LSW908(1/2)
LSW909(1/2)
LSW910(1/2)
LSW911(1/2)
LSW907(1/2)
FB903
S904
25 25
• IC Block Diagrams
IC401 BD3442FS-E2 (MAIN Board (1/4)) IC750 TDA8588BJ/N2/R1 (MAIN Board (2/4))
TAB 1
BUS-L 1 2 SDA
VCC2 32 FIL OUT-FL- 3 I2C BUS
100k
4 SCL
31 GND FL
BUS-R 2
OUT-FL+ 5
100k INPUT INPUT VOLUME1 TREBLE VOLUME2 6 VP2
SELECTOR GAIN /MUTE /BASS
TU-L 3 /MIDDLE I2C 30 SDA OUT-RL- 7
BUS
100k LOGIC RL 8 PGND3
29 SCL
TU-R 4 OUT-RL+ 9
100k 28 MUTE 10 SVR

IN-RL 11
MUTE
CD-L 5
VCC 27 VCC 12 IN-FL
100k S-GND 13
PROTECTION/
CD-R 6 DIAGNOSTIC 14 IN-FR
MUTE
100k FADER 26 OUTF1 IN-RR 15
AUX-L 7 EFFECT 16 BEEP
VP
250k FADER 25 OUTF2 OUT-RR+ 17
AUX-G 8 RR 18 PGND2
FADER 24 OUT-R1 OUT-RR- 19
250k
AUX-R 9
FADER 23 OUT-R2 20 VP1
OUT-FR+ 21
250k
DS32 10 STANDBY/
FR MUTE 22 STB
OUT-FR- 23
DS11 11 22 OUTS1
FADER CHIP DETECT/
DS22 12 DIAGNOSTIC 24 PGND1
LPF BATTERY TEMPERATURE
21 OUTS2 DIAG 25 DETECTION PROTECTION ENABLE
EBIAS 13 FADER LOGIC
20 ADJ 26 RST
DS21 14
19 SOUT
ANT-REM 27 SWITCH
SPECTRUM
DS11 15 ANALYZER 18 DATA
DS31 16 17 CLK
28 CRES
AMP-REM 29 SWITCH
30 AUDIO8.3V
REGULATOR
SERVO5V 31
32 GND
MECH6V 33
34 PANEL+B
VP 35
REFERENCE 36 CBU
VOLTAGE
LOADDUMP BACK-UP
B.UP+B 37 REGULATOR PROTECTION SWITCH
26 26
• IC PIN DESCRIPTIONS
• IC501 MB90F045PF-G-9065-SPE1 (SYSTEM CONTROL) (MAIN BOARD (3/4))
Pin No. Pin Name I/O Pin Description
1 AREASEL0 I Destination function setting pin 0
5 BEEP O BEEP signal output to power amplifier
6 CYRIL_SEL I Cyril correspondence discrimination signal input “L”: No correspondence
7 NOSE_SW I Front panel attachment detect signal input “L”: Panel on, “H”: Panel off
8 DIAG I Status signal input from power amplifier
9 VOLATT O Electronic volume attenuate control signal output
10 NCO O Not used. (Open)
11 VSS — Ground pin
12 TUATT O Tuner mute control signal output
13 NSMASK O Noise mask signal output Not used in this set. (Open)
14 to 22 NCO O Not used. (Open)
23 VCC5 — Power supply pin (+3.3V)
24 EEP_SIO I/O EEPROM bus serial data signal input/output
25 EEP_CKO O EEPROM bus serial clock signal output
26 AMPSTB O Stand-by signal output to power requlation
27 LCD_CE O Chip enable signal output to LCD driver
28 LCD_SO O Serial data signal output to LCD driver
29 LCD_CKO O Serial clock signal output to LCD driver
30 RDS ON O RDS (radio data system) ON signal output Not used in this set. (Open)
31 RE-IN0 I Rotary encoder signal input 0
32 RE-IN1 I Rotary encoder signal input 1
33 I2C_CKO O I2C bus serial clock signal output
34 I2C_SIO I/O I2C bus serial data signal input/output
35 DAVDD — A/D converter power supply pin (+3.3V)
36 AVRH — A/D converter external reference power supply pin (+3.3V)
37 DAVSS — A/D converter Ground pin
38 QUALITY I Noise detect signal input
39 VSM I S-meter voltage detect signal input
40 KEYIN1 I Key signal input 1
41 KEYIN0 I Key signal input 0
42 VSS — Ground pin
43 RC_IN0 I Rotary commander key signal input Not used in this set. (Pull up)
49 MD0 I Operation mode setting pin 0 (Pull up)
50 MD1 I Operation mode setting pin 1 (Pull up)
51 MD2 I Operation mode setting pin 2 (Pull down)
52 KEYACK I Key acknowledgment detect signal input
53 TU_ATTIN I Tuner mute zero cross detect signal input Not used in this set. (Pull down)
54 BUIN I Back-up power supply detect signal input
56 DAVN I RDS data block synchronized detect signal input Not used in this set. (Pull down)
58 UNISI I S-BUS data signal input
59 UNISO O S-BUS data signal output
60 UNISCK O S-BUS clock signal output
27
Pin No. Pin Name I/O Pin Description

61 CODEC_SEL I MP3 select signal input “H”: MP3, “L”: Non-MP3
62 ILLUMI SEL I Illumination voltage setting signal input “H”: 10.4 V, “L”: 9.0 V
64 SIRCS I Remote control signal input
Memory mode select signal input Not used in this set. (Pull up)
68 FLASH_W I
Normally “H” input: Single chip mode, after reset “L”: Flash write mode
69, 70 NCO O Not used. (Open)
71 RC_IN1 I Rotary commander shift key signal input Not used in this set. (Pull up)
72 ACC_IN I Accessory power supply detect signal input
73 TESTIN I Test mode detect signal input Not used in this set. (Pull up)
74 TELATT I Telephone attenuate detect signal input Not used in this set. (Pull down)
76 AD_ON O A/D converter power supply control signal output
77 RESET I System reset signal input
79 XOUT O Low speed operation clock signal output (32.768 kHz)
80 XIN I Low speed operation clock signal input (32.768 kHz)
81 VSS1 — Ground pin
82 OSCIN I High speed operation clock signal input (18.432 MHz)
83 OSCOUT O High speed operation clock signal output (18.432 MHz)
84 VCC3 — Power supply pin (+3.3 V)
85 DEMOSEL I DEMO select signal input “H”: DEMO on, “L”: DEMO off
86 ATT O Audio mute control signal output
87 BUSON O BUS ON signal output
88 SYSRST O System reset signal output
93 Z-MUTE I CD zero cross mute detect signal input
94 B OUT SEL I Black out with/without discrimination select signal input “H”: Black out
95 INI RS I REAR/SUB INITIAL setting signal input “H”: REAR INITIAL, “L”: SUB INITIAL
96 MO-DISP I Motion display signal input “H”: Motion display on, “L”: Motion display off
Dimmer select signal input “H”: Dimmer, “L”: No dimmer
97 DIM_SEL I
Not used in this set. (Pull down)
98 CD_ON I CD mechanism servo power supply control request signal input
99 CDM_ON I CD mechanism deck power supply control request signal input
Illumination color select signal input Not used in this set. (Pull down)
100 COL_SW I
“H”: Two colors selection/initial slave, amber, “L”: Color/slave, amber
28
SECTION 6
EXPLODED VIEWS
NOTE:
• The mechanical parts with no reference • -XX and -X mean standardized parts, so The components identified by
number in the exploded views are not supplied. they may have some difference from the mark 0 or dotted line with mark
• Items marked “*” are not stocked since original one. 0 are critical for safety.
they are seldom required for routine service. • Color Indication of Appearance Parts Replace only with part number
Some delay should be anticipated Example : specified.
when ordering these items. KNOB, BALANCE (WHITE) ... (RED)
R R
Parts Color Cabinet’s Color
• Accessories are given in the last of this parts list.
6-1. MAIN SECTION
not supplied A
MG-101TC-188//C
#2
#1 7
#3
A B
#5
FU601
#4
#6 #3
4
#4
not supplied
5
not supplied
3 #1 6
TU1
not supplied
2
#1
not supplied
#1
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
1 X-2178-981-1 PANEL ASSY, SUB FU601 1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) 10A
2 2-583-939-01 SCREW (+B 2X4) TU1 A-3220-960-B TUNER UNIT (TUX-032)
3 X-2179-691-1 LOCK ASSY #1 7-685-792-09 SCREW +PTT 2.6X6 (S)
4 2-348-996-01 SCREW (+PTT 2.6X6), GROUND POINT #2 7-685-790-01 SCREW +PTT 2.6X4 (S)
5 A-1286-356-A MAIN BOARD, COMPLETE (GT270/GT270S) #3 7-685-793-09 SCREW +PTT 2.6X8 (S)
5 A-1286-389-A MAIN BOARD, COMPLETE (GT170/GT170S) #4 7-685-794-09 SCREW +PTT 2.6X10 (S)
6 2-345-298-01 PLATE (TU), GROUND #5 7-685-134-19 SCREW +P 2.6X8 TYPE2 NON-SLIT
7 1-833-974-31 CONNECTION CORD FOR AUTOMOBILE #6 7-621-284-40 SCREW +P 2.6X10
(POWER)
29
6-2. FRONT PANEL SECTION
60
59
RE901
60
not supplied
not supplied
58
57
61
LCD901 not supplied
(KEY board)
J901
56
not supplied not supplied
not supplied
52
not supplied
55
54 not supplied
51
53
51 A-1286-360-A PANEL COMPLETE ASSY, FRONT (GT270) 55 X-2186-575-1 KNOB (VOL) (SV) ASSY (GT270/GT270S)
51 A-1286-366-A PANEL COMPLETE ASSY, FRONT (GT270S) 56 2-349-626-01 SPRING (RELEASE)
51 A-1286-391-A PANEL COMPLETE ASSY, FRONT (GT170) 57 1-780-533-11 CONDUCTIVE BOARD, CONNECTION
51 A-1286-398-A PANEL COMPLETE ASSY, FRONT (GT170S) 58 3-214-226-11 ILLUMINATOR (LCD)
52 X-2178-983-1 BUTTON ASSY (S) 59 3-214-215-01 PANEL, BACK
53 3-251-320-01 EMBLEM (NO. 2.5), SONY 60 3-250-543-91 SCREW (+B P-TITE M2)
54 A-1286-362-A PANEL SUB ASSY, FRONT (GT270) 61 X-2186-697-1 CASE ASSY (for FRONT PANEL)
54 A-1286-368-A PANEL SUB ASSY, FRONT (GT270S) J901 1-820-624-11 SMALL TYPE JACK (VERTICAL) (AUX)
54 A-1286-393-A PANEL SUB ASSY, FRONT (GT170) LCD901 1-802-511-11 DISPLAY PANEL, LIQUID CRYSTAL
54 A-1286-400-A PANEL SUB ASSY, FRONT (GT170S) RE901 1-479-902-21 ENCODER, ROTARY (PUSH SELECT/VOLUME)
55 X-2178-982-1 KNOB (VOL) (SV) ASSY (GT170/GT170S)
30
6-3. CD MECHANISM SECTION

(MG-101TC-188//C)
101
102
not supplied not supplied 103
#7
#7
105
not supplied
not supplied
not supplied
not supplied
not supplied
104
not supplied
not supplied
not supplied
not supplied
107
106
106
101 A-1283-704-A MECHANICAL BLOCK ASSY (08) 105 3-348-998-31 SCREW (M1.4X2.5), TAPPING, PAN
102 A-1283-705-A DAXEV08//C 106 3-352-758-31 SCREW (M1.7X2.5), TOOTHED LOCK
0 103 X-2149-672-1 SERVICE ASSY, OP (DAX-25A) 107 A-1201-631-A SERVO BOARD, COMPLETE
104 2-626-869-21 SCREW (M2X3), SERRATION #7 7-627-000-00 SCREW, PRECISION +P 1.7X2.2 TYPE 3
31
SECTION 7
KEY
ELECTRICAL PARTS LIST
NOTE:
• Due to standardization, replacements in • Items marked “*” are not stocked since The components identified by
the parts list may be different from the they are seldom required for routine service. mark 0 or dotted line with mark
parts specified in the diagrams or the Some delay should be anticipated 0 are critical for safety.
components used on the set. when ordering these items. Replace only with part number
• -XX and -X mean standardized parts, so • SEMICONDUCTORS specified.
they may have some difference from the In each case, u : µ, for example:
original one. uA.. : µA.. uPA.. : µPA.. When indicating parts by reference
• RESISTORS uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD.. number, please include the board.
All resistors are in ohms. • CAPACITORS
METAL:Metal-film resistor. uF : µF
METAL OXIDE: Metal oxide-film resistor. • COILS
F:nonflammable uH : µH
• Abbreviation
CH : Chinese model
KEY BOARD LED941 8-719-053-09 LED SML-310VTT86 (Z)
********** LED942 8-719-053-09 LED SML-310VTT86 (OFF)
LED943 1-216-864-11 SHORT CHIP 0
1-780-533-11 CONDUCTIVE BOARD, CONNECTION LED944 8-719-053-09 LED SML-310VTT86 (SOURCE)
3-214-226-11 ILLUMINATOR (LCD) LED945 8-719-053-09 LED SML-310VTT86 (MODE)
< CAPACITOR > LED951 8-719-053-09 LED SML-310VTT86 (RING ILLUMINATION)

LED952 8-719-053-09 LED SML-310VTT86 (RING ILLUMINATION)
C971 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V LED953 8-719-053-09 LED SML-310VTT86 (RING ILLUMINATION)
(GT270/GT270S)
C981 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V < SWITCH >
C983 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C984 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V LSW901 1-786-805-12 SWITCH, TACTILE (WITH LED) (EQ3)
C986 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10V LSW902 1-786-805-12 SWITCH, TACTILE (WITH LED) (DSPL)
(GT170/GT170S)
C987 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V LSW902 1-786-805-12 SWITCH, TACTILE (WITH LED) (DSPL/SCRL)
(GT270/GT270S)
< CONNECTOR > LSW903 1-786-805-12 SWITCH, TACTILE (WITH LED)
(M > SEEK+)
CN901 1-819-758-12 PLUG, CONNECTOR 15P LSW904 1-786-805-12 SWITCH, TACTILE (WITH LED)
(. m SEEK–)
< DIODE >
LSW905 1-786-805-12 SWITCH, TACTILE (WITH LED) (BTM)
D903 6-501-782-01 DIODE MAZ8180GMLS0 LSW906 1-786-805-12 SWITCH, TACTILE (WITH LED) (1)
D981 6-501-730-01 DIODE MAZ8051GMLS0 (GT170/GT170S)
D982 8-719-988-61 DIODE 1SS355TE-17 LSW906 1-786-805-12 SWITCH, TACTILE (WITH LED) (1/ALBUM –)
D991 6-501-743-01 DIODE MAZ8068GMLS0 (GT270/GT270S)
D992 6-501-743-01 DIODE MAZ8068GMLS0 LSW907 1-786-805-12 SWITCH, TACTILE (WITH LED) (2)
(GT170/GT170S)
D993 6-501-743-01 DIODE MAZ8068GMLS0 LSW907 1-786-805-12 SWITCH, TACTILE (WITH LED) (2/ALBUM +)
D994 6-501-743-01 DIODE MAZ8068GMLS0 (GT270/GT270S) (GT270/GT270S)
D998 1-216-295-11 SHORT CHIP 0
LSW908 1-786-805-12 SWITCH, TACTILE (WITH LED) (3/REP)
< JUMPER RESISTOR > LSW909 1-786-805-12 SWITCH, TACTILE (WITH LED) (4/SHUF)
LSW910 1-786-805-12 SWITCH, TACTILE (WITH LED) (5)
FB903 1-216-295-11 SHORT CHIP 0 LSW911 1-786-805-12 SWITCH, TACTILE (WITH LED) (6/PAUSE)
< IC > < TRANSISTOR >
IC901 6-710-047-01 IC LC75836WH-US-E Q931 8-729-027-44 TRANSISTOR DTC114TKA-T146

IC971 6-600-629-01 IC RS-470 (IR) (GT270/GT270S) Q932 6-551-444-01 TRANSISTOR RT1N436C-TP-1
< JACK > < RESISTOR >
J901 1-820-624-11 SMALL TYPE JACK (VERTICAL) (AUX) R901 1-216-820-11 METAL CHIP 820 5% 1/10W
R902 1-216-821-11 METAL CHIP 1K 5% 1/10W
< LIQUID CRYSTAL DISPLAY > R903 1-216-821-11 METAL CHIP 1K 5% 1/10W
R904 1-216-822-11 METAL CHIP 1.2K 5% 1/10W
LCD901 1-802-511-11 DISPLAY PANEL, LIQUID CRYSTAL R905 1-216-823-11 METAL CHIP 1.5K 5% 1/10W
< DIODE > R907 1-216-820-11 METAL CHIP 820 5% 1/10W

R908 1-216-821-11 METAL CHIP 1K 5% 1/10W
LED931 6-501-339-01 LED NESW505CT-AST (LCD BACK LIGHT) R909 1-216-821-11 METAL CHIP 1K 5% 1/10W
32
KEY MAIN
R910 1-216-822-11 METAL CHIP 1.2K 5% 1/10W A-1286-356-A MAIN BOARD, COMPLETE (GT270/GT270S)
R911 1-216-823-11 METAL CHIP 1.5K 5% 1/10W A-1286-389-A MAIN BOARD, COMPLETE (GT170/GT170S)
R912 1-216-824-11 METAL CHIP 1.8K 5% 1/10W *********************
R913 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R914 1-216-827-11 METAL CHIP 3.3K 5% 1/10W 7-621-284-40 SCREW +P 2.6X10
7-685-134-19 SCREW +P 2.6X8 TYPE2 NON-SLIT
R915 1-216-828-11 METAL CHIP 3.9K 5% 1/10W 7-685-794-09 SCREW +PTT 2.6X10 (S)
R931 1-216-812-11 METAL CHIP 180 5% 1/10W
R932 1-216-812-11 METAL CHIP 180 5% 1/10W < CAPACITOR >
R933 1-216-812-11 METAL CHIP 180 5% 1/10W
R934 1-216-822-11 METAL CHIP 1.2K 5% 1/10W C4 1-126-947-11 ELECT 47uF 20% 35V
C5 1-126-947-11 ELECT 47uF 20% 35V
R941 1-216-813-11 METAL CHIP 220 5% 1/10W C6 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
R944 1-216-811-11 METAL CHIP 150 5% 1/10W
R946 1-216-811-11 METAL CHIP 150 5% 1/10W C151 1-126-960-11 ELECT 1uF 20% 50V
R948 1-216-811-11 METAL CHIP 150 5% 1/10W C153 1-126-961-11 ELECT 2.2uF 20% 50V
R949 1-216-809-11 METAL CHIP 100 5% 1/10W
R954 1-216-811-11 METAL CHIP 150 5% 1/10W
(GT270/GT270S) C312 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
R975 1-216-809-11 METAL CHIP 100 5% 1/10W
(GT270/GT270S) C343 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
R981 1-216-811-11 METAL CHIP 150 5% 1/10W
R984 1-216-821-11 METAL CHIP 1K 5% 1/10W C412 1-104-665-11 ELECT 100uF 20% 25V
R985 1-216-821-11 METAL CHIP 1K 5% 1/10W C413 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C431 1-126-964-11 ELECT 10uF 20% 50V
R986 1-216-821-11 METAL CHIP 1K 5% 1/10W C432 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
R987 1-216-857-11 METAL CHIP 1M 5% 1/10W
R988 1-216-840-11 METAL CHIP 39K 5% 1/10W C435 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
R992 1-216-864-11 SHORT CHIP 0 C441 1-126-964-11 ELECT 10uF 20% 50V
C442 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
< ROTARY ENCODER > C445 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
C451 1-126-964-11 ELECT 10uF 20% 50V
RE901 1-479-902-21 ENCODER, ROTARY (PUSH SELECT/VOLUME)
< SWITCH > C454 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
S901 1-786-653-11 SWITCH, TACTILE (Z) C461 1-126-964-11 ELECT 10uF 20% 50V
S902 1-786-653-11 SWITCH, TACTILE (OFF) C462 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
S903 1-786-653-11 SWITCH, TACTILE (SOURCE)
S904 1-786-653-11 SWITCH, TACTILE (MODE) C464 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
************************************************************* C465 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
C471 1-126-964-11 ELECT 10uF 20% 50V
C479 1-124-589-11 ELECT 47uF 20% 16V
C481 1-126-964-11 ELECT 10uF 20% 50V

C503 1-124-584-00 ELECT 100uF 20% 10V
C507 1-162-917-11 CERAMIC CHIP 15PF 5% 50V
C508 1-162-916-11 CERAMIC CHIP 12PF 5% 50V
33
MAIN
C509 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V D754 6-501-362-01 DIODE 1A4-TA26
C511 1-124-584-00 ELECT 100uF 20% 10V D756 6-501-362-01 DIODE 1A4-TA26
< FERRITE BEAD >
C601 1-112-302-11 ELECT 3300uF 20% 16V FB1 1-500-245-11 INDUCTOR, FERRITE BEAD
C602 1-165-319-11 CERAMIC CHIP 0.1uF 50V FB604 1-500-245-11 INDUCTOR, FERRITE BEAD
C618 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V < FUSE >
C622 1-126-926-11 ELECT 1000uF 20% 10V FU601 1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) 10A
C623 1-126-926-11 ELECT 1000uF 20% 10V
C631 1-126-160-11 ELECT 1uF 20% 50V < IC >
C751 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25V IC401 6-710-065-01 IC BD3442FS-E2
IC501 6-807-750-01 IC MB90F045PF-G-9065-SPE1
C753 1-128-551-11 ELECT 22uF 20% 63V IC602 6-709-458-01 IC XC61CN2802NR
C754 1-124-257-00 ELECT 2.2uF 20% 50V IC750 6-705-360-02 IC TDA8588BJ/N2/R1
C756 1-216-864-11 SHORT CHIP 0 < JACK >
C758 1-124-261-00 ELECT 10uF 20% 50V
J1 1-815-185-13 JACK (ANTENNA)
C763 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16V J330 1-774-698-11 JACK, PIN 2P (AUDIO OUT REAR)
C765 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25V < JUMPER RESISTOR >
C770 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16V JC504 1-216-864-11 SHORT CHIP 0
JC510 1-216-864-11 SHORT CHIP 0
JC754 1-216-296-11 SHORT CHIP 0
< CONNECTOR > JC755 1-216-296-11 SHORT CHIP 0
CN601 1-774-701-21 PIN, CONNECTOR 16P < COIL >

CN701 1-819-773-13 SOCKET, CONNECTOR 15P
CNP301 1-820-611-11 CONNECTOR, BOARD TO BOARD 28P L1 1-469-844-11 INDUCTOR 2.2uH
L151 1-216-295-11 SHORT CHIP 0
< DIODE > L601 1-456-617-11 COIL, CHOKE
D1 6-501-734-01 DIODE MAZ8056GMLS0 < TRANSISTOR >

D153 6-501-743-01 DIODE MAZ8068GMLS0
D479 6-501-193-01 DIODE 1SS355WTE-17 Q1 6-551-431-01 TRANSISTOR 2SC6027T100-QR
D502 6-502-131-01 DIODE LRB751V-40T1G (GT270/GT270S) Q431 8-729-027-44 TRANSISTOR DTC114TKA-T146
D503 6-501-193-01 DIODE 1SS355WTE-17 Q441 8-729-027-44 TRANSISTOR DTC114TKA-T146
Q451 8-729-027-44 TRANSISTOR DTC114TKA-T146
D510 6-501-656-01 DIODE LBAT54ALT1G Q461 8-729-027-44 TRANSISTOR DTC114TKA-T146
D511 6-500-335-01 DIODE MC2838-T112-1
D512 6-501-654-01 DIODE LBAT54CLT1G Q471 6-551-856-01 TRANSISTOR LTC614TKFP8T146
D580 6-501-747-01 DIODE MAZ8075GMLS0 Q478 8-729-027-43 TRANSISTOR DTC114EKA-T146
D581 6-501-782-01 DIODE MAZ8180GMLS0 Q479 8-729-027-23 TRANSISTOR DTA114EKA-T146
Q481 6-551-856-01 TRANSISTOR LTC614TKFP8T146
D601 6-501-571-01 DIODE 1N5404-C311-3 Q580 8-729-027-43 TRANSISTOR DTC114EKA-T146
D617 6-501-782-01 DIODE MAZ8180GMLS0
D704 6-501-743-01 DIODE MAZ8068GMLS0 Q581 8-729-038-28 TRANSISTOR RT1N441C-TP-1
D719 6-501-782-01 DIODE MAZ8180GMLS0 Q582 8-729-620-07 TRANSISTOR 2SC3052EF-T1-LEF
D751 6-501-362-01 DIODE 1A4-TA26 Q631 8-729-620-07 TRANSISTOR 2SC3052EF-T1-LEF
Q664 8-729-027-23 TRANSISTOR DTA114EKA-T146
D752 6-501-362-01 DIODE 1A4-TA26
D753 6-501-362-01 DIODE 1A4-TA26
34
MAIN
< RESISTOR > R533 1-216-845-11 METAL CHIP 100K 5% 1/10W
R534 1-216-833-11 METAL CHIP 10K 5% 1/10W
R1 1-216-821-11 METAL CHIP 1K 5% 1/10W R535 1-216-833-11 METAL CHIP 10K 5% 1/10W
R2 1-414-595-11 INDUCTOR, FERRITE BEAD R536 1-216-833-11 METAL CHIP 10K 5% 1/10W
R4 1-216-839-11 METAL CHIP 33K 5% 1/10W
R540 1-216-845-11 METAL CHIP 100K 5% 1/10W
R13 1-414-595-11 INDUCTOR, FERRITE BEAD
R151 1-216-817-11 METAL CHIP 470 5% 1/10W R544 1-216-821-11 METAL CHIP 1K 5% 1/10W
R546 1-216-845-11 METAL CHIP 100K 5% 1/10W
R155 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R301 1-216-821-11 METAL CHIP 1K 5% 1/10W R557 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R558 1-216-821-11 METAL CHIP 1K 5% 1/10W
R412 1-218-883-11 METAL CHIP 33K 0.5% 1/10W R565 1-216-845-11 METAL CHIP 100K 5% 1/10W
R413 1-216-864-11 SHORT CHIP 0
R414 1-216-864-11 SHORT CHIP 0 R566 1-216-845-11 METAL CHIP 100K 5% 1/10W
R567 1-216-845-11 METAL CHIP 100K 5% 1/10W
R432 1-216-833-11 METAL CHIP 10K 5% 1/10W R570 1-216-817-11 METAL CHIP 470 5% 1/10W
R442 1-216-833-11 METAL CHIP 10K 5% 1/10W
R578 1-216-821-11 METAL CHIP 1K 5% 1/10W
R471 1-216-813-11 METAL CHIP 220 5% 1/10W
R601 1-216-845-11 METAL CHIP 100K 5% 1/10W
R479 1-216-805-11 METAL CHIP 47 5% 1/10W R631 1-249-425-11 CARBON 4.7K 5% 1/4W
R502 1-216-821-11 METAL CHIP 1K 5% 1/10W
R503 1-216-821-11 METAL CHIP 1K 5% 1/10W R634 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R636 1-216-845-11 METAL CHIP 100K 5% 1/10W
R507 1-216-845-11 METAL CHIP 100K 5% 1/10W
R671 1-216-809-11 METAL CHIP 100 5% 1/10W
R511 1-216-821-11 METAL CHIP 1K 5% 1/10W R673 1-218-871-11 METAL CHIP 10K 0.5% 1/10W
R513 1-216-845-11 METAL CHIP 100K 5% 1/10W
R676 1-216-821-11 METAL CHIP 1K 5% 1/10W
R521 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R690 1-216-845-11 METAL CHIP 100K 5% 1/10W
R522 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
(GT270/GT270S)
R527 1-216-845-11 METAL CHIP 100K 5% 1/10W (GT170/GT170S)
R531 1-216-845-11 METAL CHIP 100K 5% 1/10W
R532 1-216-845-11 METAL CHIP 100K 5% 1/10W
35
MAIN SERVO
< SWITCH > PARTS FOR INSTALLATION AND CONNECTIONS
***************************************
S502 1-571-478-11 SWITCH, SLIDE (FREQUENCY SELECT)
151 X-2179-430-1 FRAME ASSY, FITTING
< TUNER UNIT > 152 2-686-802-01 COLLAR
153 3-246-011-01 KEY (FRAME)
TU1 A-3220-960-B TUNER UNIT (TUX-032) 154 A-1082-993-A SCREW ASSY (BS4), FITTING
155 3-259-776-01 SCREW (+K 5X8 TP)
< VIBRATOR >
156 1-833-974-31 CONNECTION CORD FOR AUTOMOBILE
X501 1-813-524-21 VIBRATOR, CERAMIC (18.432MHz) (POWER)
X502 1-767-317-11 VIBRATOR, CRYSTAL (32.768kHz)
************************************************************* 151 152 153
A-1201-631-A SERVO BOARD, COMPLETE
**********************
*************************************************************
×2
MISCELLANEOUS
*************** 154
7 1-833-974-31 CONNECTION CORD FOR AUTOMOBILE 155
(POWER)
0 103 X-2149-672-1 SERVICE ASSY, OP (DAX-25A)
************************************************************* ×4
ACCESSORIES 156
************
1-479-077-13 REMOTE COMMANDER (RM-X151)

(GT270/GT270S)
2-548-729-01 LID, BATTERY CASE (for RM-X151)
(GT270/GT270S)
3-215-427-31 MANUAL, INSTRUCTION (ENGLISH,SPANISH,
PERSIAN) (EXCEPT CH)
3-215-427-41 MANUAL, INSTRUCTION (ENGLISH,
SIMPLIFIED CHINESE) (CH)
3-215-428-31 MANUAL, INSTRUCTION, INSTALL (ENGLISH,
SPANISH,PERSIAN) (EXCEPT CH)
3-215-428-41 MANUAL, INSTRUCTION, INSTALL (ENGLISH,

SIMPLIFIED CHINESE) (CH)
X-2186-697-1 CASE ASSY (for FRONT PANEL)
*************************************************************
36
MEMO
37
REVISION HISTORY
Clicking the version allows you to jump to the revised page.

Also, clicking the version at the top of the revised page allows you to jump to the next revised page.
Ver. Date Description of Revision

1.0 2007. 08 New
38

Sony Cdxgt170 Manual

Uploaded by

Copyright:

Available Formats

Sony Cdxgt170 Manual

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Sony Cdxgt170 Manual

Uploaded by

Copyright:

Available Formats

CDX-GT170/GT170S/

FM/MW/SW COMPACT DISC PLAYER

Power amplifier section Notes on Chip Component Replacement

General TEST DISCS

MPEG Layer-3 audio coding technology and

Design and specifications are subject to change without

NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK

NOTES ON LASER DIODE EMISSION CHECK

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE

This compact disc player is classified as a CLASS 1 LASER TABLE OF CONTENTS

7. ELECTRICAL PARTS LIST .................................. 32

: LEAD FREE MARK

NOTE FOR REPLACEMENT OF THE SERVO BOARD

NOTE FOR REPLACEMENT OF THE AUX JACK (J901)

Location of controls and basic operations

AUDIO OUT REAR*

AUDIO OUT REAR*

* AUDIO OUT SUB/REAR

CDX-GT370S/GT370 *1 CDX-GT370S/GT370 only

BUS REAR FRONT

desde la antena del automóvil

Connection diagram Diagrama de conexión

3-1. SUB PANEL ASSY

3-2. CD MECHANISM BLOCK

3-3. MAIN BOARD 3-4. SERVO BOARD

3-5. CHASSIS (T) SUB ASSY

3-6. ROLLER ARM ASSY

3-7. CHASSIS (OP) ASSY

3-8. CHUCKING ARM SUB ASSY

3-9. SLED MOTOR ASSY

3-10. OPTICAL PICK-UP SECTION

3-11. OPTICAL PICK-UP

Note: Follow the disassembly procedure in the numerical order given.

3-1. SUB PANEL ASSY

4 sub panel assy

3-2. CD MECHANISM BLOCK

3-3. MAIN BOARD

3-4. SERVO BOARD

WHT 2 toothed lock screw

1 Remove the eleven solders. 5 SERVO board

4 optical pick-up (16 core)

3-5. CHASSIS (T) SUB ASSY

2 two precision screws

4 chassis (T) sub assy

3-6. ROLLER ARM ASSY

5 roller arm assy

3-7. CHASSIS (OP) ASSY

6 chassis (OP) assy

1 tension spring (KF)

7 coil spring (damper) (natural)

8 coil spring (damper) (black)

3-8. CHUCKING ARM SUB ASSY

3 chucking arm sub assy

Note: Be careful not to touch the turn table.

3-9. SLED MOTOR ASSY

2 three serration screws

3 sled motor assy

Note for Assembly

three serration screws