Sony CDX Gt527ee Gt570 Gt570s

CDX-GT527EE/GT570/
GT570S
SERVICE MANUAL E Model
CDX-GT570/GT570S
Ver. 1.3 2007.12 Russian Model
CDX-GT527EE
Photo: CDX-GT570
• The tuner and CD sections have no adjustments. Model Name Using Similar Mechanism NEW
CD Drive Mechanism Type MG-101TC-188//Q
Optical Pick-up Name DAX-25A
SPECIFICATIONS
CD player section Selectivity 75 dB at 400 kHz
Signal-to-noise ratio 120 dB Signal-to-noise ratio 67 dB (stereo), 69 dB (mono)
Frequency response 10 – 20,000 Hz Harmonic distortion at 1 kHz
Wow and flutter Below measurable limit 0.5% (stereo), 0.3% (mono)
Separation 35 dB at 1 kHz
Tuner section Frequency response 30 – 15,000 Hz
FM
Tuning range CDX-GT527EE: MW/LW (CDX-GT527EE)
FM1/FM2: 87.5 – 108.0 MHz Tuning range MW: 531 – 1,602 kHz
(at 50 kHz step) LW: 153 – 279 kHz
FM3: 65 – 74 MHz (at 30 kHz step) Antenna (aerial) terminal
CDX-GT570/GT570S: External antenna (aerial) connector
87.5 – 108.0 MHz (at 50 kHz step) Intermediate frequency 10.7 MHz/450 kHz
87.5 – 107.9 MHz (at 200 kHz step) Sensitivity MW: 30 µV, LW: 40 µV
(except EA model)
FM tuning interval CDX-GT570/GT570S:
50 kHz/200 kHz switchable – Continued on next page –
(except EA model)
Antenna (aerial) terminal
External antenna (aerial) connector
Intermediate frequency 10.7 MHz/450 kHz
Usable sensitivity 9 dBf
FM/MW/LW COMPACT DISC PLAYER

CDX-GT527EE
FM/MW/SW COMPACT DISC PLAYER
CDX-GT570/GT570S
9-887-812-04 Sony Corporation

2007L04-1 Audio Business Group
© 2007.12 Published by Sony Techno Create Corporation
CDX-GT527EE/GT570/GT570S
MW (CDX-GT570/GT570S) SERVICE NOTES

Tuning range 531 – 1,602 kHz (at 9 kHz step)
530 – 1,710 kHz (at 10 kHz step) NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK
(except EA model)
OR BASE UNIT
MW tuning interval 9 kHz/10 kHz switchable
(except EA model)
The laser diode in the optical pick-up block may suffer electrostatic
Antenna (aerial) terminal breakdown because of the potential difference generated by the
External antenna (aerial) connector charged electrostatic load, etc. on clothing and the human body.
Intermediate frequency 10.7 MHz/450 kHz During repair, pay attention to electrostatic breakdown and also use
Sensitivity 30 µV the procedure in the printed matter which is included in the repair
parts.
SW (CDX-GT570/GT570S) The flexible board is easily damaged and should be handled with
Tuning range SW1: 2,940 – 7,735 kHz
care.
SW2: 9,500 – 18,135 kHz
(except for 10,140 – 11,575 kHz)
Antenna (aerial) terminal NOTES ON LASER DIODE EMISSION CHECK
External antenna (aerial) connector The laser beam on this model is concentrated so as to be focused on
Intermediate frequency 10.7 MHz/450 kHz the disc reflective surface by the objective lens in the optical pick-
Sensitivity 30 µV up block. Therefore, when checking the laser diode emission,
observe from more than 30 cm away from the objective lens.
Power amplifier section
Outputs Speaker outputs (sure seal connectors)
Speaker impedance 4 – 8 ohms CAUTION
Maximum power output
52 W × 4 (at 4 ohms)
Use of controls or adjustments or performance of procedures
other than those specified herein may result in hazardous
General radiation exposure.
Outputs Audio outputs terminal (front, rear/sub
switchable) (CDX-GT527EE)
Audio outputs terminal (front/rear) If the optical pick-up block is defective, please replace the whole
(CDX-GT570/GT570S)
optical pick-up block.
Subwoofer output terminal (mono)
(CDX-GT570/GT570S)
Never turn the semi-fixed resistor located at the side of optical pick-
Power antenna (aerial) relay control terminal up block.
Power amplifier control terminal
Inputs Telephone ATT control terminal optical pick-up
(CDX-GT527EE)
BUS control input terminal
BUS audio input terminal
Remote controller input terminal
Antenna (aerial) input terminal
AUX input jack (stereo mini jack)
Tone controls Low: ±10 dB at 60 Hz (XPLOD)
Mid: ±10 dB at 1 kHz (XPLOD)
High: ±10 dB at 10 kHz (XPLOD)
Power requirements 12 V DC car battery (negative ground (earth))
Dimensions Approx. 178 × 50 × 180 mm
(7 1/8 × 2 × 7 1/8 in.) (w/h/d)
Mounting dimensions Approx. 182 × 53 × 162 mm
(7 1/4 × 2 1/8 × 6 1/2 in.) (w/h/d)
Mass Approx. 1.2 kg (2 lb. 11 oz.)
Supplied accessories Card remote commander: RM-X151
Parts for installation and connections (1 set)
MPEG Layer-3 audio coding technology and

patents licensed from Fraunhofer IIS and Thomson.
Design and specifications are subject to change without semi-fixed resistor

notice.
• Abbreviation
EA: Saudi Arabia model
SAFETY-RELATED COMPONENT WARNING!!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE

WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
IN SUPPLEMENTS PUBLISHED BY SONY.
2
Ver. 1.2
This compact disc player is classified as a CLASS 1 LASER

product. The CLASS 1 LASER PRODUCT label is located on the
• UNLEADED SOLDER
Boards requiring use of unleaded solder are printed with the lead-
exterior. free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
: LEAD FREE MARK

Unleaded solder has the following characteristics.
This label is located on the bottom of the chassis. • Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
Notes on Chip Component Replacement
about 350°C.
• Never reuse a disconnected chip component.
Caution: The printed pattern (copper foil) may peel away if the
• Notice that the minus side of a tantalum capacitor may be damaged
heated tip is applied for too long, so be careful!
by heat.
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow)
TEST DISCS
than ordinary solder so use caution not to let solder bridges
Please use the following test discs for the check on the CD section.
occur such as on IC pins, etc.
• Usable with ordinary solder
YDES-18 (Part No. 3-702-101-01)
It is best to use only unleaded solder but unleaded solder may
PATD-012 (Part No. 4-225-203-01)
also be added to ordinary solder.
• CD playback
You can play CD-DA (also containing CD TEXT) and CD-R/
CD-RW (MP3/WMA files).
Type of discs Label on the disc
CD-DA
MP3
WMA
3
TABLE OF CONTENTS
1. SERVICE NOTE ........................................................ 5
2. GENERAL
Location of controls and basic operations
(CDX-GT527EE) ............................................................ 6
Connections (CDX-GT527EE) ....................................... 6
(CDX-GT570/GT570S) ................................................... 8
Connections (CDX-GT570/GT570S) .............................. 8
3. DISASSEMBLY
3-1. Sub (AUX) Panel Assy .................................................... 11
3-2. CD Mechanism Block ..................................................... 11
3-3. MAIN Board .................................................................... 12
3-4. SERVO Board .................................................................. 12
3-5. Chassis (T) Sub Assy ....................................................... 13
3-6. Roller Arm Assy .............................................................. 13
3-7. Chassis (OP) Assy ........................................................... 14
3-8. Chucking Arm Sub Assy ................................................. 14
3-9. Sled Motor Assy .............................................................. 15
3-10. Optical Pick-up Section ................................................... 16
3-11. Optical Pick-up ................................................................ 16
4. DIAGNOSIS FUNCTION ........................................ 17
5. DIAGRAMS
5-1. Block Diagram –Main Section– ...................................... 21
5-2. Block Diagram –Display Section– .................................. 22
5-3. Printed Wiring Board –Main Section– ............................ 23
5-4. Schematic Diagram –Main Section (1/3)– ...................... 24
5-7. Printed Wiring Board –Sub Section– .............................. 27
5-8. Schematic Diagram –Sub Section– ................................. 27
5-9. Printed Wiring Board –Display Section– ........................ 28
5-10. Schematic Diagram –Display Section– ........................... 29
6. EXPLODED VIEWS
6-1. Main Section .................................................................... 33
6-2. Front Panel Section ......................................................... 34
6-3. CD Mechanism Section (MG-101TC-188//Q) ................ 35
7. ELECTRICAL PARTS LIST .................................. 36
4
SECTION 1
SERVICE NOTE
EXTENSION CABLE AND SERVICE POSITION
When repairing or servicing this set, connect the jig (extension cable)
as shown below.
• Connect the MAIN board (CN350) and the SERVO board (CN2)
with the extension cable (Part No. J-2502-076-1).
MAIN BOARD
CN350 J-2502-076-1
SERVO BOARD
CN2
NOTE FOR REPLACEMENT OF THE SERVO BOARD

When repairing, the complete SERVO board (A-1177-201-A) should
be replaced since any parts in the SERVO board cannot be repaired.
NOTE FOR REPLACEMENT OF THE AUX JACK (J901)

To replace the AUX jack requires alignment.
1. Insert the AUX jack into the KEY board.
2. Place the KEY board on the front panel.
3. Solder the three terminals of the jack.
KEY board
AUX jack
front panel
5
SECTION 2
GENERAL This section is extracted
from instruction manual.
• Location of controls and basic operations (CDX-GT527EE)
• Connections (CDX-GT527EE)
6
7
• Location of controls and basic operations (CDX-GT570/GT570S)

Main unit F OPEN button page 5 The following buttons on the card remote
commander have also different buttons/functions
1 2 3 4 5 6 G ALBM +/– buttons (during MP3/WMA from the unit. Remove the insulation film before
playback) use (page 4).
To skip albums (press); skip albums
OFF OPEN
continuously (press and hold). qk < (.)/, (>) buttons
ALBM
To control CD/radio, the same as (SEEK)
SOURCE
H Receptor for the card remote –/+ on the unit.
SEEK SEEK AUX
commander Setup, sound setting, etc., can be operated by
< ,.
ALBM
I SEEK –/+ buttons
MODE REP SHUF PAUSE SCRL CD: ql DSPL (display) button
PUSH SELECT
BTM 1 2 3 4 5 6 DSPL To skip tracks (press); skip tracks To change display items.
continuously (press, then press again within
about 1 second and hold); reverse/fast- w; VOL (volume) +/– button
forward a track (press and hold). To adjust volume.
7 8 9 q; qa qs qd qf Radio: wa ATT (attenuate) button
Front panel removed To tune in stations automatically (press); find To attenuate the sound. To cancel, press
a station manually (press and hold). again.
qg qh qj J MODE button page 8 ws SEL (select) button
To select the radio band (FM/MW/SW)*. The same as the select button on the unit.
K BTM button page 8 wd M (+)/m (–) buttons
To start the BTM function (press and hold). To control CD, the same as (ALBM) +/– on
L Frequency select switch (located on the the unit.
bottom of the unit) Setup, sound setting, etc., can be operated by
See “Frequency select switch” in the M m.
supplied installation/connections manual. wf SCRL (scroll) button
RESET
M Number buttons To scroll the display item.
CD: wg Number buttons
(3): REP page 8 To receive stored stations (press); store
(4): SHUF page 8 stations (press and hold).
Card remote commander This section contains instructions on the location (6): PAUSE
of controls and basic operations. For details, see To pause playback of a CD on this unit. * In the case of a CD/MD changer being connected;
RM-X151 the respective pages. when (SOURCE) is pressed, the connected device
To cancel, press again. (“MD”) will appear in the display, depending on
For optional device (CD/MD changer, etc.,) Radio:
1 OFF ATT
wa operation, see “Using optional equipment” on To receive stored stations (press); store
which device is connected. Furthermore, if (MODE)
is pressed, you can switch the changer.
page 10. The corresponding buttons on the card
3 ws remote commander control the same functions as
stations (press and hold).
Note
SOURCE SEL MODE
q; those on the unit. N DSPL (display)/SCRL (scroll) button If the unit is turned off and the display disappears, it
qk A OFF button
page 8 cannot be operated with the card remote commander
unless (SOURCE) on the unit is pressed, or a disc is
+ To change display items (press); scroll the inserted to activate the unit first.
To power off; stop the source. display item (press and hold).
wd B Volume control dial/select button
–
O RESET button page 4
page 9
ql DSPL SCRL wf To adjust volume (rotate); select setup items P Z (eject) button page 5
(press and rotate). To eject the disc.
1 2 3
4 5 6
wg C SOURCE button Q Disc slot page 5
To power on; change the source (Radio/CD/ To insert the disc.
AUX)*.
+
w; VOL
–
D Display window
E AUX input jack page 10
To connect a portable audio device.
6 7
• Connections (CDX-GT570/GT570S)
Connection example
Notes (2-A)
A • Be sure to connect the ground (earth) lead before connecting
the amplifier.
• The alarm will only sound if the built-in amplifier is used.
Tip (2-B)
When connecting only a single CD/MD changer or other optional
device, connect directly to this unit.
FRONT
AUDIO OUT
Ejemplo de conexión
Notas (2-A)
• Asegúrese de conectar primero el cable de conexión a masa
SUB OUT (MONO) REAR antes de realizar la conexión del amplificador.
AUDIO OUT • La alarma sonará solamente si se utiliza el amplificador
integrado.
Sugerencia (2-B)
Cuando conecte un solo cambiador de CD/MD u otro dispositivo
opcional, hágalo directamente a esta unidad.
B
BUS AUDIO IN
BUS CONTROL IN
8
*1 RCA pin cord (not supplied)

*2 Insert with the cord upwards.
*1 Cable con terminales RCA
*1 (no suministrado)
*2 Insertar con el cable hacia arriba.
SUB OUT (MONO) FRONT REMOTE

AUDIO OUT IN
*2
L
*1 R
BUS AUDIO IN BUS REAR FRONT
IN AUDIO OUT
from car antenna (aerial)
desde la antena del automóvil
REAR Fuse (10 A) BUS
AUDIO OUT Fusible (10 A) CONTROL IN
Blue/white striped 2 Black

Con rayas azules y blancas Negro
AMP REM
3 Max. supply current 0.3 A 1
Corriente máx. de alimentación de 0,3 A
White
Blanco
Left Blue
Izquierdo White/black striped Azul
Con rayas blancas y negras ANT REM
Max. supply current 0.1 A 2
Grey Corriente máx. de alimentación de 0,1 A
Gris
Right
Derecho Grey/black striped
Con rayas grises y negras Red
Rojo
Green
Verde
4
Left
Izquierdo Green/black striped
Con rayas verdes y negras
Purple Yellow
Morado Amarillo
Right
Derecho 5
Purple/black striped
Con rayas moradas y negras
Connection diagram Diagrama de conexión

1 To a metal surface of the car 1 A una superficie metálica del automóvil
First connect the black ground (earth) lead, then connect the Conecte primero el cable de conexión a masa negro, y después
yellow and red power supply leads. los cables amarillo y rojo de entrada de alimentación.
2 To the power antenna (aerial) control lead or 2 Al cable de control de la antena motorizada
power supply lead of antenna (aerial) booster o al cable de fuente de alimentación del
Notes amplificador de señal de la antena
• It is not necessary to connect this lead if there is no power Notas
antenna (aerial) or antenna (aerial) booster, or with a • Si no se dispone de antena motorizada ni de amplificador
manually-operated telescopic antenna (aerial). de antena, o se utiliza una antena telescópica accionada
• When your car has a built-in FM/MW/SW antenna (aerial) manualmente, no será necesario conectar este cable.
in the rear/side glass, see “Notes on the control and power • Si el automóvil dispone de una antena de FM/MW/SW
supply leads.” integrada en el cristal trasero o lateral, consulte “Notas sobre
3 To AMP REMOTE IN of an optional power los cables de control y de fuente de alimentación”.
amplifier 3 A AMP REMOTE IN de un amplificador de
This connection is only for amplifiers. Connecting any other potencia opcional
system may damage the unit. Esta conexión es solamente para amplificadores. La conexión
4 To the +12 V power terminal which is de cualquier otro sistema puede dañar la unidad.
energized in the accessory position of the 4 Al terminal de alimentación de +12 V que
ignition switch recibe energía en la posición de accesorios del
Notes interruptor de la llave de la llave de encendido
• If there is no accessory position, connect to the +12 V Notas
power (battery) terminal which is energized at all times. • Si no hay posición de accesorios, conéctelo al terminal
Be sure to connect the black ground (earth) lead to a de alimentación (batería) de +12 V que recibe energía sin
metal surface of the car first. interrupción.
• When your car has a built-in FM/MW/SW antenna (aerial) Asegúrese de conectar primero el cable de conexión a masa
in the rear/side glass, see “Notes on the control and power negro a una superficie metálica del automóvil.
supply leads.” • Si el automóvil dispone de una antena de FM/MW/SW
5 To the +12 V power terminal which is integrada en el cristal trasero o lateral, consulte “Notas sobre
energized at all times los cables de control y de fuente de alimentación”.
Be sure to connect the black ground (earth) lead to a metal 5 Al terminal de alimentación de +12 V que recibe
surface of the car first. energía sin interrupción
Notes on the control and power supply leads Asegúrese de conectar primero el cable de conexión a masa
• The power antenna (aerial) control lead (blue) supplies +12 V negro a una superficie metálica del automóvil.
DC when you turn on the tuner. Notas sobre los cables de control y de fuente de alimentación
• When your car has built-in FM/MW/SW antenna (aerial) in the • El cable de control de la antena motorizada (azul) suministrará cc
rear/side glass, connect the power antenna (aerial) control de + 12 V cuando conecte la alimentación del sintonizador.
lead (blue) or the accessory power supply lead (red) to the • Si el automóvil dispone de una antena de FM/MW/SW integrada
power terminal of the existing antenna (aerial) booster. For en el cristal trasero o lateral, conecte el cable de control de antena
details, consult your dealer. motorizada (azul) o el cable de entrada de alimentación auxiliar
• A power antenna (aerial) without a relay box cannot be used (rojo) al terminal de alimentación del amplificador de antena
with this unit. existente. Para obtener más información, consulte a su distribuidor.
Memory hold connection • Con esta unidad no es posible utilizar una antena motorizada sin
When the yellow power supply lead is connected, power will caja de relé.
always be supplied to the memory circuit even when the ignition Conexión para protección de la memoria
switch is turned off. Si conecta el cable de entrada de alimentación amarillo, el circuito
Notes on speaker connection de la memoria recibirá siempre alimentación, aunque apague el
• Before connecting the speakers, turn the unit off. interruptor de la llave de encendido.
• Use speakers with an impedance of 4 to 8 ohms, and with Notas sobre la conexión de los altavoces
adequate power handling capacities to avoid its damage. • Antes de conectar los altavoces, desconecte la alimentación de la
• Do not connect the speaker terminals to the car chassis, or unidad.
connect the terminals of the right speakers with those of the • Utilice altavoces con una impedancia de 4 a 8 Ω con la capacidad
left speaker. de potencia adecuada para evitar que se dañen.
• Do not connect the ground (earth) lead of this unit to the • No conecte los terminales de altavoz al chasis del automóvil, ni
negative (–) terminal of the speaker. conecte los terminales del altavoz derecho con los del izquierdo.
• Do not attempt to connect the speakers in parallel. • No conecte el cable de conexión a masa de esta unidad al
• Connect only passive speakers. Connecting active speakers terminal negativo (–) del altavoz.
(with built-in amplifiers) to the speaker terminals may damage • No intente conectar los altavoces en paralelo.
the unit. • Conecte solamente altavoces pasivos. Si conecta altavoces
• To avoid a malfunction, do not use the built-in speaker leads activos (con amplificadores integrados) a los terminales de
installed in your car if the unit shares a common negative (–) altavoz, puede dañar la unidad.
lead for the right and left speakers. • Para evitar fallas de funcionamiento, no utilice los cables de
• Do not connect the unit’s speaker leads to each other. altavoz integrados instalados en el automóvil si la unidad comparte
Note on connection un cable negativo común (–) para los altavoces derecho e
If speaker and amplifier are not connected correctly, “FAILURE” izquierdo.
appears in the display. In this case, make sure the speaker and • No conecte los cables de altavoz de la unidad entre sí.
amplifier are connected correctly. Nota sobre la conexión
Si el altavoz y el amplificador no están conectados correctamente,
aparecerá “FAILURE” en la pantalla. Si es así, compruebe la
conexión de ambos dispositivos.
9
SECTION 3
DISASSEMBLY
Note: This set can be disassemble according to the following sequence.
SET
3-1. SUB (AUX) PANEL ASSY

(Page 11)
3-2. CD MECHANISM BLOCK

(Page 11)
3-3. MAIN BOARD 3-4. SERVO BOARD

(Page 12) (Page 12)
3-5. CHASSIS (T) SUB ASSY

(Page 13)
3-6. ROLLER ARM ASSY

(Page 13)
3-7. CHASSIS (OP) ASSY

(Page 14)
3-8. CHUCKING ARM SUB ASSY

(Page 14)
3-9. SLED MOTOR ASSY

(Page 15)
3-10. OPTICAL PICK-UP SECTION

(Page 16)
3-11. OPTICAL PICK-UP

(Page 16)
10
Note: Follow the disassembly procedure in the numerical order given.
3-1. SUB (AUX) PANEL ASSY
3 two claws
2 two claws
4 flexible flat cable (17 core)

1 two screws (CN702)
(+PTT 2.6 × 6)
5 sub (AUX) panel assy
3-2. CD MECHANISM BLOCK
6 bracket (CD)
7 CD mechanism block
5 two screws
(+PTT 2.6 × 4)
3
2 screw
(+PTT 2.6 × 6)
4 CN350
1 screw
(+PTT 2.6 × 6)
11
3-3. MAIN BOARD
CDX-GT570/GT570S
7 screw 8 two screws 5 screw
(+PTT 2.6 × 10) (+P 2.6 × 8) (+PTT 2.6 × 8)
9 two screws
(+PTT 2.6 × 10)
0 two screws
(+P 2.6 × 8)
1 three ground point screws 6 cord (RCA)
(+PTT 2.6 × 6)
2 two screws
(+PTT 2.6 × 8)
qa screw
(+PTT 2.6 × 10)
qs heat sink
4 CN410 (3P)
qd MAIN board
3 insulating sheet
3-4. SERVO BOARD
WHT
RED
BLK
WHT 2 toothed lock screw

RED (M 1.7 × 2.5)
BLK
RED
ORG 3 toothed lock screw
BLE (M 1.7 × 2.5)
YEL SERVO board
GRY
1 Remove the eleven solders. 5 SERVO board
4 optical pick-up (16 core)

(CN1)
claw
claw
12
3-5. CHASSIS (T) SUB ASSY
2 two precision screws

1 two precision screws (+P 1.7 × 2.2)
(+P 1.7 × 2.2)
4 chassis (T) sub assy
3 claw
3-6. ROLLER ARM ASSY
5 roller arm assy
4 gear (RA1)
1 spring (RAL)
3 washer
2 spring (RAR)
13
3-7. CHASSIS (OP) ASSY
6 chassis (OP) assy
1 tension spring (KF)

5
7 coil spring (damper) (natural)
8 coil spring (damper) (blue)

4 slider (R)
3 lever (D)
2 gear (LE1)
3-8. CHUCKING ARM SUB ASSY
3 chucking arm sub assy
1 spring
Note: Have this portion receive the chassis. Note: Have this portion receive the chassis.
Note: Be careful not to touch the turn table.
14
3-9. SLED MOTOR ASSY
2 three serration screws

(M 2 × 3)
3 sled motor assy
1 spring
turn table spring
stand
Note:
Never remove these parts since they were adjusted.
stand
Note: Place the stand with care not to touch the turn table.
Note for Assembly
three serration screws

(M 2 × 3)
sled motor assy
Note: Take care to prevent the chassis from being bent

when tightening the three machine screws.
15
3-10. OPTICAL PICK-UP SECTION
2 optical pick-up section
Note: Be careful not to touch the lens and hologram

terminal when removing the optical pick-up section.
3-11. OPTICAL PICK-UP
1 pan tapping screw

(M 1.4 × 2.5)
2 leaf spring (sub guide)
3 leaf spring (OP)
5 optical pick-up
4 lead screw assy
Notes for Assembly
Prevent the end of the Prevent the end of the There is space at the end of the
leaf spring (sub guide) from being leaf spring (sub guide) from being leaf spring (sub guide) to avoid
in contact with the OP slide base. in contact with the OP slide base. contact with the slide.
16
SECTION 4
DIAGNOSIS FUNCTION
Description of the Diagnostics function: 4. Contents of each display mode
4-1. Reset count display mode
1. Setting the Diag display mode
With the power off, press the [4/SHUF] button, [5] button, and
[4/SHUF] button on the set body or the remote control (for more
than 2 seconds) in turn.
Reset count
2. Canceling the Diag display mode (in hexadecimal format)
During the Diag function mode, press the [OFF] button. Diag code
01: Reset count
3. Initial display in the Diag display mode
Just when the Diag mode is entered, “reset count” is displayed.
The display mode is switched by each rotation of 4-2. Reset count by watchdog timer display mode
SEEK +/M > or SEEK –/. m buttons.
Reset count display

Reset count
(in hexadecimal format)
Diag code
02: Number of resets by watchdog timer
Reset count by watchdog timer display

4-3. Number of connected units display mode
Number of connected units display Shown the number of connected units for
CD-C, MD-C and XM respectivery from
the rightmost (in hexadecimal format).
Recency of information
1 - 3: 1 represents the latest.
Diag code
Operating hours display 03: Number of connected unit
The display mode is switched by each rotation of [ALBM +] or [ALBM

--] buttons during the number of connected units display mode.
CD error information display No. of connected units history 1 (latest) display
OFFSET/FAILURE error display No. of connected units history 2 display
No. of connected units history 3 display
17
4-4. Operating hours display mode 4-5-2. Disc type and operating hours
Disc type
Indication Disc type
Operating hours Operating hours 0 MP3
(in hexadecimal format) Disc type 1 WMA
Diag code 2 AAC
04: Operating hours 3 ATRAC
Diag code 8 CD-DA
05: CD error information F UNKNOWN
4-5. CD error information display mode
4-5-1. Error description
--] buttons during the CD error information display mode.
Error description
Error information
CD error info history 1 (latest)
(in hexadecimal Indication Description
Error description plus error details display
format) 1X SERVO ERROR
3X LOADING ERROR
1 - 3: 1 represents the latest. 4X TRACK JUMP
Diag code 5X TEXT ERROR
05: CD error information FX MECHA ERROR
CD error info history 1 (latest)
Disc type plus operating hours display
CD error info history 2




18
4-6. OFFSET/FAILURE error display mode
Operating hours
Error description
(0: OFFSET, 1: FAILURE)
Diag code
06: OFFSET/FAILURE

--] buttons during the OFFSET/FAILURE error display mode.
OFFSET/FAILURE error history 1 (latest) display
OFFSET/FAILURE error history 2 display
OFFSET/FAILURE error history 3 display
19
Ver. 1.2 SECTION 5
DIAGRAMS
THIS NOTE IS COMMON FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed in each block.)
for schematic diagram: for printed wiring boards:

Note: Note:
• All capacitors are in µF unless otherwise noted. (p: pF) • X : parts extracted from the component side.
50 WV or less are not indicated except for electrolytics • Y : parts extracted from the conductor side.
and tantalums. • a : Through hole.
• All resistors are in Ω and 1/4 W or less unless otherwise • : Pattern from the side which enables seeing.
specified. (The other layers' patterns are not indicated.)
• f : internal component.
• C : panel designation. Caution:
Pattern face side: Parts on the pattern face side seen from the
Note: The components identified by mark 0 or dotted line (Side B) pattern face are indicated.
with mark 0 are critical for safety. Parts face side: Parts on the parts face side seen from the
Replace only with part number specified. (Side A) parts face are indicated.
• A : B+ Line.
• Abbreviation
• B : B– Line.
IND : Indian model
• H : adjustment for repair.
MX : Mexican model
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
no mark : FM
( ) : MW
< > : CD
• Voltages are taken with a VOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal production
tolerances.
• Waveforms are taken with a oscilloscope.
Voltage variations may be noted due to normal production
tolerances.
• Circled numbers refer to waveforms.
• Signal path.
J : CD
F : FM
f : MW
g : AUDIO
L : AUX
• Abbreviation
IND : Indian model
MX : Mexican model
• Waveforms
— MAIN Board —
1 IC50 9 (XTI) 2 IC501 ul (XOUT) 3 IC501 id (OSCOUT)

(CDX-GT527EE only)
2.1 Vp-p 1.6 Vp-p 2.5 Vp-p
8.664 MHz 32.768 kHz 18.432 MHz
1 V/DIV, 50 nsec/DIV 1 V/DIV, 50 nsec/DIV 1 V/DIV, 50 nsec/DIV
20
5-1. BLOCK DIAGRAM — MAIN SECTION —
GT570/GT570S
-1
L SUB OUT
ELECTRONIC VOLUME -2 (MONO)
IC401 R
J451 (1/2)
-1 J451 (2/2)
BUS L 2 A2
R-CH 1 A1 -5
AUDIO L
IN -2 R-CH FRONT AUDIO OUT
R GT527EE -6
R-CH R
R-CH GT570/GT570S
J901 -3
9 DP2 OUTS2 21
AUX L
R-CH 7 DP1 OUTS1 22 R-CH (REAR) GT570/GT570S REAR AUDIO OUT
-4
8 DN R-CH R
GT527EE MUTE POWER AMP, MULTI
Q430 VOLTAGE REGULATOR REAR/SUB AUDIO OUT
TU1 IC300
TUNER UNIT CN300
GT527EE
OUTF2 25 12 IN-RR 1
J1 FL+
1 ANT L 4 4 B2 OUTR2 23 11 IN-RF LF+ 5
(ANTENNA) 9
R 3 R-CH R-CH 3 B1 OUTF1 26 R-CH (FRONT) LF- 3 FL-
OUTR1 24 R-CH (REAR) MUTE MUTE 2
6 C2 Q440 Q470 LR+ 9 RL+
MUTE 10
R-CH 5 C1 MUTE 28 LR- 7 RL-
SA_IN GT570/GT570S
SOUT 19
SA_CLK
CLK 17 R-CH
SA_DATA 4
DATA 18 D491 FR+
SCL MUTE DRIVE 12
SCL 29 BATT FR-
SDA Q491,492 R-CH 3
SDA 30 RR+
11
RR-
12C-SCL 12C-SCL
SCL 13 4 SCL
12C-SDA SYSTEM CONTROL 12C-SDA
SDA 14 2 SDA
IC501 (1/2) 5
SW1 29 AMP-R
AU8V 10 VCC8.3V 6
VSM SW2 27 ANT-R
TU+5V 11 VDD5V S-METER 6 39 VSM
TUATT
+3.3V 15 E2PVDDTUN_MUTE 7 12 TU ATT SCL FU601
I2C_CKO 33 16
EEPCKO SDA VP 35 +B
E2PSCL 16 25 EEP_CKO I2C_SIO 34
EEPSIO BATT
E2PSDA 17 24 EEP_SIO SA_IN
SA_IN 44
SA_CLK
QUALITY 5 38 QUALITY SA_CLO 45
SA_DATA
SA_DATA 32 REG2 37 U-COM (+5V)
+3.3V NS MUTE
MASK 13 NSMASK VOLATT 9
Q1
B+ SWITCH 30 RDSON
Q50
REG1 30 AU8V
RDS OUT 9 16 MPX INTN 15 56 DAVN BEEP 5 16 ACGND REG3 31 SERVO3.3V
10 XTO SCL AMPSTB 26 22 STB REG4 33 MECHA6V
X50 SCL 11
MUTE_CON 8 SDA DIAG 8 25 DIAG REG5 34 DISP+B (+9V)
8.664MHz SDA 12
9 XTI
GT527EE
RDS RECEIVER
IC50
CN350 53 TU_ATTIN
ACC DETECT 7
ACC_IN 72 ACC
11 AU_LCH Q702
89 EJECT_OK_SW
15 AU_RCH UNISO GT527EE
R-CH
21 EJECT_OK D511
22 UNISO
59 UNISO TEL–ATT 13
24 UNISI UNISI TEL–ATT
58 UNISI TELATT 74 DETECT
26 UNICLK UNISCK Q701
60 UNISCK
16 Z-MUTE
93 Z-MUTE
CD 5 CD-ON
98 CD_ON
MECHANISM 7 CDM-ON
UNIT 99 CDM_ON
28 LINK_OFF LINK_OFF SYSRST
(MG-101TC) BUS INTERFACE D603
6 SYS_RST IC601
88 SYSRST BATT
77 RESET OPEN-MUTE 100
27 BUS_ON BUSON D493 SYSRST BATTERY CHECK
87 BUSON 13 RST BATT 3
25 B/U_CHECK BUIN D400 BUSON Q605
54 BUIN ATT 86 12 BUSIN D602 8
9 A-ATT UNISCK CNJ400
11 CLK-IN 6 3 (BUS CONTROL IN)
18 D_3.3V BUIN
SERVO3.3V 10 B/U-C DATA I/O 6 5 2
19 A_3.3V RESET UNISI
8 DATA OUT CLK 4 4 1
8 BU_3.3V IC602 UNISO
+3.3V 9 DATA IN RST 2 7
1,2 DR_6V
MECHA6V 1 VOUT VDD 2 +3.3V
S103 LINK ON/OFF CONTROL
BUS ON 1
RESET Q600,601
• R-CH is omitted due to same as L-CH.
TH400
• Signal Path LINK_OFF +3.3V REG
IC502
: CD BATT
: FM +3.3V 3 VOUT VIN 2 U-COM (+5V)
DOOR_SW DISPLAY
: MW A SECTION
: AUX D494 (Page 22) +5V REG
TU+5V AU8V
Q3
: AUDIO
21 21
Ver. 1.2
5-2. BLOCK DIAGRAM — DISPLAY SECTION —
SYSTEM CONTROL LCD DRIVER/LED CONTROL

IC501 (2/2) IC901
RC1
J370 71 RC_IN1
( REMOTE
IN
) RC0
43 RC_IN0 LCD_SO 28 78 DI
S1 3
| LCD901
I
D501 LCD_CKO 29 77 CL S62 64 LIQUID
LCD_CE 27 76 CE CRYSTAL
COM1 65 DISPLAY
I | PANEL
40 KEYIN1 COM4 68
KEY MATRIX LED930,931
S901–915
41 KEYIN0 ( LCDLIGHT
BACK
)
LCD BACK LIGHT
DIMMER 80 DIMMER CONTROL
Q901
S201
Z
GREEN
KEY ACK
RED
ENABLE 52 KEY ACK
Q501 1 2 DISP+B
RE901 76 AD_ON GT527EE

VOLUME
CONTROL LED902–916,
DIAL/ 943,947, D946,949,
SELECT 948,950 951–966,993
KEY
BUTTON
+ ( KEY/VOLUME
ILLUMINATION ) ( ILLUMINATION )
ROTARY RE-0
48 RE_IN1
ENCODER RE-1
47 RE_IN0 GREEN LED
CONTROL
79 XOUT Q919
X501 RED LED
32.768kHz CONTROL
80 XIN Q920 R994
82 OSCIN
X500
18.432MHz
GT570/GT570S
83 OSCOUT
CN901 CN201
14 14
70 DOOR_SW
LED201
LED DRIVER (DISC IN)
DOOR_IND 46 LED202
Q589,590
Z
MAIN DOOR_SW
SECTION
A REMOTE CONTROL
SIGNAL RECEIVER
(Page 21) IC971
SIRCS 64 3 OUT
+3.3V
FM(200k)
S501 MW(10k)
3 AREASEL2
( FREQUENCY
SELECT
) FM(50k)
MW(9k)
E,IND,MX MODEL
• Abbreviation S102
IND: Indian model (FRONT PANEL DETECT)
MX : Mexican model
7 NOSE_SW
22 22
Ver. 1.2
5-3. PRINTED WIRING BOARD — MAIN SECTION — : Uses unleaded solder.
1 2 3 4 5 6 7 8 9 10 11 12 13
J451
A
J370
GT527EE
CNJ400
R474
CN300
JW123
JC302
JW1
JC300
JW98
JW99
JC301
C442 C422
L301
JW4
C432 C452 C324 C323
C414 C413 JW2
B
C602
FU601
C309
R432 R452 R442 R422 IC300 JW3
C307 C305 C304 C301
C494
L303 L302
R416
J1
C320 D605 JW5
JW17
Q440 Q420
Q450
D606
C462
JW7
R701
JW6
JW9
JW8
JW10
R417 JC303
D311
D309
D310
JW11
JW12
JW13
JW14
JW21
JW18 C312
Q430
R418 JW164 JW161
D312
C446
JC490 C472 JW19 D701
C C423
JW23
JW24
R419 JW20 C902
C701
D308
JC491 JW22 C465
C303
JW162
D307
Q460
R462
D306
R703
D607
C443 C901
C447
C310
JW166
Q701
Q470
C466
R421 L300
D305
CN410 JW25 D304
JC304 JW167 D302
C308
R441 C704
R431
JW26 R472 JW169

R704
C421 JW168
C14 R702 JW163
R411 JW27 D301 JW28 D303
C431
C471
C411
C306
JC305 JW29 GT570/GT570S
R471 JW16
JW36
D
C300
TU1
R355 JC430 R461 C451 JW30
R451
JW42
JW34
R356 TH400
C461
JW40 JW31
JW33
C361 C321
C441
JW32
C362
C491
C313
JW45
C485
JW38
JW39
C314
JW37
JW41
JW44
JW78
R2 C360 C316
JW35
C487 C600
C330 CN350
C317
R3
R359
R361 C484
Q491
C1 R491 C315
Q492
FB402
FB401
JC401
R4
C331
R611
JW165
C501
C325
IC502
C4
C502
C327 C403
R5 JW65
C417
R8
R1 R358
E C328 JW43 D491
C405
IC401
JC603
JW50
JW53
R9 JW66 JC400 C412
JW54
Q1
R480 C318
R604 R603
R610
R357
C410
C2 JW58 C503 R402 FB408
FB407
D602
C3 C480 R510 C419 JW51
JW55
C363
JC3 R301
D2 R481 C482 R433 JW59 FB403
C319 R506 C418
R10
C9 C483 R505 FB406 D603

R483 JW62 JW60 R503 R401
Q605
JC518
R545 JC504
R482
D493
R504
C7 R507 FB405 JC602
C364
R12
D494
JW63 R502 JW69
JW57
JW56
JW61
JW67 R13 JC350 C415 D604
C5
R454
C481 JW64 R559 JW71
R572
JW68 C8 R501 R494 FB404
C504
R302
L1
Q3
R453 R512 R351

F R6
R563
JW76
JW75
JW77
JC522
JW70
JW80
Q600
R455 R511
JW102
S501 R579 JW72
C401
JW74
R580
R554 R7 R608
R573
JW73
R574
JW81 L4
JW106
JW100
JW101 R561
Q601
R537
JW107
JW105
JW110 R583 R706
R705
C402
L500
JW115
JW109
JW103
JW104
JW108
R562 D702
JW94
JW111 JW82
R549
R407
R55 C506 R400
R575
JW113
JW114
R14 R514
JW112
C702
R707
C505
JW93
R58
JC509
R708
R515 JW83
Q702
C50
R553
R548
C63 R518 R509 R500

R516
1
C51
50
C52 C58 JW160
D400
JW84
• Semiconductor Location
IC
R536
JC503
JW97
JW85
C523
R576
C54
JW87
G C64 R513
IC50
C55 C53 R517

Ref. No. Location Ref. No. Location Ref. No. Location
R551
R54 R577 X501 C516
JC501
JW142
R53 L2
JC9
R533 JW88
JW92
JW91
R606
IC601
JW90
JW143
JW159
R540
JW145
R519
D2 E-3 D310 C-7 IC502 E-6
JW95
JW86
JC600
JW96
R52 R57 L3 JC523 X500
JW148
C515 R607
JW147
R11
C507
D101 H-3 D311 C-7 IC601 G-9

Q50
R557
R605
R601
R547
R539
R484
R529 R370 R546

X50 R520 C509 D102 I-4 D312 C-7 IC602 H-8
R534
R538
R521
C57 C508 C512 R371 R602

JC512
D103 H-4 D400 G-8
C510
JW135 C511
D511
C56
R144
R146
JC508
C513
R531
R532
JW140
R542 R530 R528 R527 C601

C61 C62
JW149
R550 R541 D104 I-4 D491 E-5 (Q1) E-3
JW138
JW137
JW158 R556
JW139
JC524
JW129
R523
D105 I-3 D493 F-7 Q3 F-3

JW119
JW118
R558
JW124
JW120
R525
Q590
R526
C519
IC602
D116
H
JW125
D106 I-3 D494 F-7 (Q50) G-2

JW141
C109 C117
R522
JW131
JW116
JW155 R555 R543

JC511 JC53
JW130
JW150
JW132
C110
D101 C116
R535 R524
JW170 D107 I-3 D501 H-6 Q420 C-4
Q589
JC90
Q501
JW171
D108 I-3 D502 H-6 Q430 C-3

D501
JW152
D103
D110
C103
JW117
R584 D109 I-3 D511 H-8 Q440 C-4

JW153
JW154
C111
D502 D110 H-3 D602 E-10 (Q450) C-4
CN702
D114 I-3 D603 F-10 Q460 C-4
D102
D109 C104 S102

L101
D108 S103
D115 I-3 D604 F-10 Q470 C-4
D116 H-4 D605 C-9 Q491 E-5
I D301 D-8 D606 C-9 Q492 E-5
D114
D115
D107
D106
D105
D104
D302 C-8 D607 C-9 Q501 H-6

D303 D-8 D701 C-8 Q589 H-2
D304 C-8 D702 G-9 Q590 H-2
D305 C-6 Q600 F-10
(Page 27) D306 C-7 (IC50) G-2 Q601 F-10
D307 C-7 IC300 B-6 Q605 F-10
D308 C-6 IC401 E-4 (Q701) C-8
D309 C-6 IC501 G-6 Q702 G-10
( ): CDX-GT527EE only
23 23
5-4. SCHEMATIC DIAGRAM — MAIN SECTION (1/3) — • Refer to page 30 for IC Block Diagrams.
C323 C303 C306

C317 C324 C308
JC302
JC300 JC301 C301 C309
R302 JC504 C319 C304 C305 C307
R301 C318
IC300
IC B/D
CN300
C465
C472 C462
C466
(Page 25)
D301
D302
C316
C315
C314
C313
C310
C320
C312
R701 C902
D701
R705 D312 D311 D310 D309 D308 D307 D306 D305 D303 D304
D702 C901
FU601
R706
D607
C702 R702
C704 R703
L300 R708 R707 R704
R491 D491
Q491
C701
Q702 Q701
Q492
C491
R604 R603
R608 D603 D602
Q605
JC602
Q600
TH400
Q601
CNJ400
C600
R610 R611 R607 IC601 C601

R602 R601
R606
JC603
D604 R605
C602
D606 D605
IC B/D D511
L303
J370 L302
L301
(Page 26)
24 24
5-5. SCHEMATIC DIAGRAM — MAIN SECTION (2/3) — • Refer to page 20 for Waveforms and page 30 for IC Block Diagrams.
J451
TU1
J1
CN410
C442 C422 C452 C432

C411 C413 C414
R411
R442 R422 R452 R432 R418 R416 JC3
C8
JW25 C9
C443 C447
C3 R12 R13 L1 R6 R7
R419 R417
R4
R5
JC303 C2 C5
R8
R9
C4
R474
C423 C446 C14
JW142
C1
Q3
C494 Q1
R1
R472 R462
D2
Q440 Q420 Q450 Q430
Q470 Q460 R10 C7

R2
L4
JC491 JC490 R3
JC304
JC305
R471 R461 JC430 R431
C471 C461 R441 R421 C431

R451
C441 C421
C451 C63
IC B/D C64
JC522
IC50
JC400 IC401
(Page 24) IC B/D C58
R55
R361
C481 JC9 C62
R482 R483 C50 C51
R484 C52 R14
C483 Q50
C61
R433 C53
C482 JW149 L2
R480 R481 R53 R54 L3 C57
C480 R11
C360 R357 R52
C361 R355 R359 R57 X50 C56
C362 R356 R358
C54 C55
C364 JC401 R58
R455 C363
R454 C328 JW115
C485
C484 R453 C327 JW125 JW158
C331 C321
C330 C300 R542
C487
(Page 26)
25 25
Ver. 1.2
5-6. SCHEMATIC DIAGRAM — MAIN SECTION (3/3) — • Refer to page 20 for Waveforms and page 31 for IC Pin Description.
(Page 24) (Page 25)
Q590
IC502
C519
D493 R543
Q589
S103
JC53 C501
IC602 C325 C502
R494
D494
R584 R533
JW88
JW170 JC524
R400 R551 JC90 Q501

R527
D502
CN350
R529
R407
R541
R526
R528
R534
R532
C515
R535
R531
R546
R530
C403
R538
C412 X501 R550
C516
FB401 R547
FB408 FB402
R370
R525 JC512 D501
FB407 JC511
X500
FB406 R402 C419
C405 C417 FB403 C506
R401 C410 R524
C505
R351 FB405 C418 R536 R523 R555 R556
FB404 R558
C415 R557
L500
D400 R579 R521
C402 R537
JC350 JC600 C513 R371 R522
C512
C401 R553 C510 R539
IC501
C511 R540
R520 JC508 JC501
C509 JC523
JW129 C508
R563 C507 R519
R572
R573 R548
R549
R513
R576 JC509
R577
CN702
S501
R554
L101
R144
JC518
R502
R504
R574
R507
C117
R580
R514
R515
R516
R506
R512
R509
R510
R561
C116 R146
JC503
(Page 27) C503
R501
R503
R505
R559
R500
R562
R545
R583
R575
C504
R511
C523
R517 R518
S102
C111
C110
C109
C104
C103
D102
D110
D109
D108
D114
D115
D107
D106
D105
D101
D104
D116
D103
26 26
5-7. PRINTED WIRING BOARD — SUB SECTION — 5-8. SCHEMATIC DIAGRAM — SUB SECTION —
: Uses unleaded solder.
1 2 3 4 5 6 7
(Page 28)
A CN202
CN201
B R202
LED202
R201 R202
R201 CN201 S201

(Page 26) (Page 29)
LED201 LED202
LED201
S201
D
(Page 23)
CN202
27 27
5-9. PRINTED WIRING BOARD — DISPLAY SECTION — : Uses unleaded solder.
1 2 3 4 5 6 7 8 9 10 11 12 13 14
A LED955
LED905
LED943
LED993
LED908
LED952
LED902
B
S907
S902
S901
LED958
D982
LED903
LED953
LED957
LED907
LED930 LED931
LED949 LCD901
LED950
C LED947 LED951
LED948 S903
LED946
S906
LED964
LED914
LED962
LED912
LED913
LED963
LED910
LED960
LED959
LED909
LED916
LED965
LED915
LED966
LED961 LED911
S904
LED906
LED956
LED904
LED954
D S905
S914
S913
S912
S911
S910
S909
S908
IC971 S915
R917 R928 R910

R977 R924 R932 R912 R911 R961
R956 R960 R962
R922
F C971 R979
R916
R931
R915
R943 R945 R990 R955 R957
R959
R921
R923
R946 R958 R914 R930 R929

R926
R906
R994
R944
D904
D906
D903
D909
Q919 Q920 R927 R925
R937
G
R953
R991
R993
R905
Q901
C982
R904
RE901
C983
J901
R982
R936 R938 IC901 R992

R951 C981 CN901
R950
R981
R948
R969 D984 C984 D905

R999
R934
R942
R984
R978
D907
R940
C980
R901
D981
R985
R907
R972
R933 R947
H
R970
R903 R971 D911 FB881

R939
FB880
R908 R954 R952
R941
R935 FB882
D908
R949
R902
• Semiconductor Location
I Ref. No. Location Ref. No. Location Ref. No. Location Ref. No. Location Ref. No. Location Ref. No. Location
D903 G-12 D984 H-8 (LED907) C-2 LED930 C-7 LED953 C-5 LED963 D-9
D904 G-11 (LED908) B-2 LED931 C-12 LED954 D-5 LED964 D-8
D905 H-10 IC901 G-9 (LED909) D-12 (LED943) B-4 LED955 B-2 LED965 D-7 (Page 27)
D906 G-11 IC971 D-3 (LED910) D-11 LED946 D-4 LED956 D-2 LED966 D-6
D907 H-10 (LED911) D-11 (LED947) C-3 LED957 C-2 LED993 B-4
D908 H-11 (LED902) B-5 (LED912) D-10 (LED948) D-4 LED958 B-2
D909 G-12 (LED903) C-5 (LED913) D-9 LED949 C-3 LED959 D-12 Q901 G-5
D911 H-11 (LED904) D-5 (LED914) D-8 (LED950) C-5 LED960 D-11 (Q919) G-5
D981 H-7 (LED905) B-2 (LED915) D-7 LED951 C-5 LED961 D-10 (Q920) G-5
D982 B-2 (LED906) D-2 (LED916) D-6 LED952 B-5 LED962 D-10
( ): CDX-GT527EE only
28 28
5-10. SCHEMATIC DIAGRAM — DISPLAY SECTION —
D982
R981
R977
R982
LED915 LED965 LED911 LED961 LED948 LED946 LED902 LED952 LED908 LED958
IC971
R978
LED931 LED913 LED963 LED909 LED959 LED943 LED993 LED905 LED955 LED907 LED957
R979
C971
LED916 LED966 LED912 LED962 LED947 LED949 LED904 LED954 LED906 LED956
R984 C981
IC901
C982
R970 LED914 LED964 LED910 LED960 LED950 LED951 R933 R934 LED903 LED953 C983
D984
R985
R971
R921 R922 R925 R926 R929 R930 R959 R960 R939 R940 R947 R948 R955 R956 R935 R936 R943 R944 R951 R952
R972
D981
R923 R924 R927 R928 R931 R932 R961 R962 R941 R942 R949 R950 R957 R958 R937 R938 R945 R946 R953 R954 C984
C980
LED930
Q901
Q919 Q920
R969
R994
CN901 D911 R990
R910 R911 R912 R914 R915 R916 R917

R999
D909
D907
D908
S908 S909 S910 S911 S912 S913 S914 S915
RE901
(Page 27) R991

R992
R993
LCD901
D906
D905
D904
D903
S901 S902 S903 S904 S905 S906 S907
FB880
R901 R902 R903 R904 R905 R906 R907 R908
J901 FB881
FB882
29 29
• IC Block Diagrams
IC300 TDA8588AJ/N2/R1 (MAIN BOARD (1/3)) IC601 BA8271F-E2 (MAIN BOARD (1/3)) IC401 BD3442FS-E2 (MAIN BOARD (2/3))
TAB 1
BUS.ON 1 BUS ON 14 VCC
2 SDA SWITCH
A1 1
LF– 3 VCC2 32 FIL
I2C BUS
RESET 100k
4 SCL RST 2 13 RST
FL SWITCH 31 GND
12 BUS.IN A2 2
LF+ 5 11 CLK-IN
6 VP2 BATTERY 100k INPUT INPUT VOLUME1 TREBLE VOLUME2
BATT 3 10 B/U-C
SWITCH SELECTOR GAIN /MUTE /BASS
LR– 7 B1 3 /MIDDLE I2C 30 SDA
BUS
RL 8 PGND3 100k LOGIC
CLK 4 29 SCL
LR+ 9 B2 4
VREF 5
10 SVR DATA I/O 6 9 DATA IN 100k 28 MUTE
IN-RL 11
MUTE
C1 5
12 IN_RR VCC 27 VCC
GND 7 8 DATA OUT
S-GND 13 100k
PROTECTION/
DIAGNOSTIC 14 IN_LR C2 6
MUTE
IN_LF 15 100k FADER 26 OUTF1

16 ACGND DP1 7 EFFECT
VP
RR+ 17 250k FADER 25 OUTF2
RR 18 PGND2 DN 8
RR– 19 FADER 24 OUTR1
250k
DP2 9
20 VP1 FADER 23 OUTR2
RF+ 21 250k
STANDBY/ DS32 10
FR MUTE 22 STB
RF– 23
DS12 11 22 OUTS1
CHIP DETECT/ FADER
DIAGNOSTIC 24 PGND1 DS22 12
BATTERY TEMPERATURE LPF
DIAG 25 DETECTION PROTECTION ENABLE 21 OUTS2
LOGIC EBIAS 13 FADER
26 RST 20 ADJ
DS21 14
19 SOUT
SW2 27 SWITCH
SPECTRUM
DS11 15 ANALYZER 18 DATA
DS31 16 17 CLK
28 CRES
SW1 29 SWITCH
30 REG1
REGULATOR
REG3 31
32 GND
REG4 33
34 REG5
VP 35
IC50 TDA7333013TR (MAIN BOARD (2/3)) (CDX-GT527EE only)
REFERENCE 36 CBU
VOLTAGE
LOADDUMP BACK-UP
REG2 37 REGULATOR PROTECTION SWITCH
3
INTERPOLATOR BAND PASS SINC4 SIGMA DELTA

16 MPX
FILTER FILTER CONVERTER
VDDA 1
SINC4REG
15 INTN
MPX
REF3 2
REF2 3 SDAOUT
RAM SDAIN 14 CSN
RDS RDSREG BUFFER 2 TEST LOGIC
REF1 4 INTN DEMODULATOR & I C/SPI SCK 13 SA
& &
SYNCHRONIZATION INTERFACE SPI 12 SDA
CONTROL PIN MUX'S
TESTREG 11 SCL
LOGIC
VSS 5
TM 6 2
10 XTO
OSCILLATOR
VDDD 7 9 XTI
RESETN 8
30 30
• IC Pin Description
IC501 MB90F045PF-G-9060-SPE1 (SYSTEM CONTROL) (MAIN BOARD (3/3))
Pin No. Pin Name I/O Pin Description
1 AREASEL0 I Destination setting pin (L: CDX-GT570/GT570S, H: CDX-GT527EE)
2 AREASEL1 I Destination setting pin (L: CDX-GT570/GT570S, H: CDX-GT527EE)
3 AREASEL2 I Destination setting pin (L: FM (50k)/MW (9k), H: FM (200k)/MW (10k))
4 AREASEL3 I Destination setting pin (Fixed at L in this set)
5 BEEP O Beep signal output to power amp IC.
Key illumination 2 colors select signal input (L: 1 color (CDX-GT570/GT570S),
6 COL_SEL I
H: 2 color (CDX-GT527EE))
7 NOSE_SW I Front panel detach detection signal input (L: with panel, H: without panel)
8 DIAG I Status signal input from power amp IC.
9 VOLATT O Attenuator control signal output to electronic volume IC.
CYRIL select signal input (L: non CYRIL (CDX-GT570/GT570S),
10 CYRIL_SEL I
H: CYRIL (CDX-GT527EE))
11 VSS — Ground
12 TUATT O Tuner mute control signal output
13 NSMASK O Noise mask signal output (CDX-GT527EE only)
14 NCO O Not used. (Open)
15 ILLUMI_SEL I Illumination voltage setting pin (L: illumination power supply 9 V)
17 AUX_SW O Not used. (Open)
18, 19 NCO O Not used. (Open)
20 MG_SEL I Mechanism deck select signal input (L: MG-101TC)
Black out select signal input (L: non black out (CDX-GT527EE),
21 B-OUT_SEL I
H: black out (CDX-GT570/GT570S))
22 DIM_SEL I Dimmer select signal input (H: non auto dimmer)
23 VCC5 — Power supply pin (+3.3 V)
24 EEP_SIO I/O Serial data signal input/output for EEPROM communication.
25 EEP_CKO O Serial clock signal output for EEPROM communication.
26 AMPSTB O Standby signal output to power amp IC.
27 LCD_CE O Chip enable signal output to LCD drive IC.
28 LCD_SO O Serial data signal output to LCD drive IC.
29 LCD_CKO O Serial clock signal output to LCD drive IC.
30 RDSON O RDS ON signal output (CDX-GT527EE only)
Rear/sub switchable select signal input (L: non rear/sub switchable
31 RS_SEL I
(CDX-GT570/GT570S), H: rear/sub switchable (CDX-GT527EE))
32 SA_DATA O Data output for electronic volume IC spectrum analyzer.
33 I2C_CKO O I2C bus serial clock signal output
34 I2C_SIO I/O I2C bus serial data signal input/output
35 DAVDD — Power supply pin for A/D converter. (+3.3 V)
36 AVRH — External reference power supply pin for A/D converter. (+3.3 V)
37 DAVSS — Ground for A/D converter.
38 QUALITY I Noise detection signal input
39 VSM I S meter voltage detection signal input
40 KEYIN1 I Key signal input 1
41 KEYIN0 I Key signal input 0
42 VSS — Ground
43 RC_IN0 I Rotary commander key signal input
44 SA_IN I Spectrum analyzer signal input
45 SA_CKO O Spectrum analyzer clock signal output
31
Pin No. Pin Name I/O Pin Description

46 DOOR_IND O DISC IN indicator LED control signal output
47 RE_IN0 I Rotary encoder signal input 0
48 RE_IN1 I Rotary encoder signal input 1
49, 50 MD0, MD1 I Signal input for operation mode designation. (Fixed at H in this set)
51 MD2 I Signal input for operation mode designation. (Fixed at L in this set)
52 KEYACK I Key acknowledge detection signal input
53 TU_ATTIN I Tuner mute zero cross detection signal input (CDX-GT527EE only)
54 BUIN I Backup power supply detection signal input
RDS data block synchronized detection signal input from RDS receiver IC.
56 DAVN I
(CDX-GT527EE only)
58 UNISI I SONY-BUS data signal input
59 UNISO O SONY-BUS data signal output
60 UNISCK O SONY-BUS clock signal output
61 to 63 NCO O Not used. (Open)
64 SIRCS I Remote control signal input
68 FLASH_W I Memory mode select signal input (Fixed at H in this set)
70 DOOR_SW I Front panel open/close detection signal input
71 RC_IN1 I Rotary commander shift key signal input
72 ACC_IN I Accessory power supply detection signal input
73 TESTIN I Test mode detection signal input (Fixed at H in this set)
74 TELATT I Telephone attenuator detection signal input (CDX-GT527EE only)
75 ILLUIN I Illumination detection signal input (H: illumination OFF)
76 AD_ON O A/D converter power supply control signal output
77 RESET I Reset signal input
79 XOUT O Sub-clock signal output (32.768 kHz)
80 XIN I Sub-clock signal input (32.768 kHz)
81 VSS1 — Ground
82 OSCIN I Main-clock signal input (18.432 MHz)
83 OSCOUT O Main-clock signal output (18.432 MHz)
84 VCC3 — Power supply pin (+3.3 V)
85 INI_RS I Rear/sub initial select signal input (L: initial sub)
86 ATT O Audio mute control signal output
87 BUSON O Bus ON signal output
88 SYSRST O System reset signal output
89 EJECT_OK_SW O Eject OK signal output
93 Z-MUTE I CD zero cross mute detection signal input
95 DEMOSEL I Demo select signal input (H: Demo ON)
Initial color setting signal input (L: blue (CDX-GT570/GT570S),
96 INI_COL I
H: green (CDX-GT527EE))
98 CD_ON I CD mechanism servo power control request signal input
99 CDM_ON I CD mechanism deck power control request signal input
100 OPEN-MUTE O Mute signal output at during the AUX source mode. (L: other, H: keep)
32
SECTION 6 Ver. 1.3
EXPLODED VIEWS
NOTE:
• The mechanical parts with no reference • Accessories are given in the last of this parts list. The components identified by
number in the exploded views are not supplied. • Abbreviation mark 0 or dotted line with mark
• Items marked “*” are not stocked since IND : Indian model 0 are critical for safety.
they are seldom required for routine service. MX : Mexican model Replace only with part number
Some delay should be anticipated EA : Saudi Arabia model specified.
when ordering these items. RU : Russian model
CDX-GT570/GT570S
6-1. MAIN SECTION
14
not supplied A
12
#3
MG-101TC-188//Q #2 14
13
FU601
#3
B
#5 #4
#1
#5
#4 #3
9
A #5
10
not supplied
not supplied
7 8 #1 11
TU1
not supplied
not supplied
not supplied
B
6 #1
2
5
1
#1 not supplied
(SUB board)
3
5 4
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
1 X-2176-202-1 LOCK ASSY 12 1-833-974-21 CONNECTION CORD FOR AUTOMOBILE
2 3-246-441-01 BUTTON (EJECT) (POWER) (GT570/GT570S)
3 1-834-507-11 CABLE, FLEXIBLE FLAT (17 CORE) 12 1-834-307-11 CONNECTION CORD FOR AUTOMOBILE
4 3-260-247-01 CUSHION (SUB PANEL) (POWER) (for Maruti Suzuki:Diesel Car)
5 3-042-244-01 SCREW (T) 13 1-833-887-11 CONNECTION CORD (RCA) (SUB OUT (MONO))
(GT570/GT570S)
6 X-2179-173-1 PANEL ASSY, SUB (AUX) 14 3-264-798-01 CAP (GT570/GT570S)
7 X-3384-203-2 GEAR ASSY FU601 1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) 10A
8 3-713-786-51 SCREW +P 2X3
9 3-376-464-11 SCREW (+PTT 2.6X6), GROUND POINT TU1 A-3220-960-B TUNER UNIT (TUX-032) (GT570/GT570S)
10 A-1312-911-A MAIN BOARD, COMPLETE (RU) TU1 A-3220-961-B TUNER UNIT (TUX-032) (GT527EE)
#1 7-685-792-09 SCREW +PTT 2.6X6 (S)
10 A-1312-912-A MAIN BOARD, COMPLETE (E,IND,MX) #2 7-685-790-01 SCREW +PTT 2.6X4 (S)
10 A-1312-914-A MAIN BOARD, COMPLETE (EA) #3 7-685-793-09 SCREW +PTT 2.6X8 (S)
11 2-021-848-01 SHEET (TU), GROUND
12 1-831-838-11 CORD (WITH CONNECTOR) (ISO) (POWER) #4 7-685-134-19 SCREW +P 2.6X8 TYPE2 NON-SLIT
(GT527EE) #5 7-685-794-09 SCREW +PTT 2.6X10 (S)
12 1-833-762-11 CONNECTION CORD FOR AUTOMOBILE
(POWER) (for Maruti Suzuki:Gasoline Car)
33
Ver. 1.3
6-2. FRONT PANEL SECTION
58
57
RE901
not supplied
58 59
56
LCD901
not supplied
(KEY board)
J901
not supplied
not supplied
not supplied
not supplied
52
55
54 53 51
51 A-1312-858-A PANEL OVERALL ASSY, FRONT (GT527EE) 54 X-2186-453-1 PANEL (SV) ASSY, FRONT (GT570)
51 A-1313-015-A PANEL OVERALL ASSY, FRONT (GT570S) 55 X-2179-191-1 KNOB ASSY (S)
51 A-1313-022-A PANEL OVERALL ASSY, FRONT 56 1-780-563-11 CONDUCTIVE BOARD, CONNECTION
(GT570:E,IND (Maruti Suzuki)) 57 X-2179-174-1 PANEL ASSY, FRONT BACK
51 A-1313-023-A PANEL OVERALL ASSY, FRONT (GT570:MX) 58 3-250-543-21 SCREW (+B P-TITE M2)
51 A-1313-085-A PANEL OVERALL ASSY, FRONT (GT570:EA)
59 X-2149-228-2 CASE ASSY (for FRONT PANEL)
52 3-264-712-01 SPRING (OPEN) J901 1-820-833-11 JACK, SMALL TYPE (VERTICAL) (AUX)
53 X-2179-192-1 BUTTON ASSY (S) (GT570) LCD901 1-802-534-11 DISPLAY PANEL, LIQUID CRYSTAL (GT527EE)
53 X-2179-230-1 BUTTON ASSY (S) (GT527EE) LCD901 1-802-535-11 DISPLAY PANEL, LIQUID CRYSTAL
53 X-2186-454-1 BUTTON ASSY (S) (GT570S) (GT570/GT570S)
54 X-2179-233-1 PANEL (SV) ASSY, FRONT (GT527EE) RE901 1-479-902-21 ENCODER, ROTARY
(VOLUME CONTROL DIAL/SELECT BUTTON)
54 X-2186-452-1 PANEL (SV) ASSY, FRONT (GT570S)
34
6-3. CD MECHANISM SECTION

(MG-101TC-188//Q)
101
102
not supplied not supplied 103
#6
#6
105
not supplied
not supplied
not supplied
not supplied
not supplied
104
not supplied
not supplied
not supplied
not supplied
107
106 106
101 A-1289-450-A MECHANICAL BLOCK ASSY (08) 105 3-348-998-31 SCREW (M1.4X2.5), TAPPING, PAN
102 A-1284-705-A DAXEV08//Q 106 3-352-758-31 SCREW (M1.7X2.5), TOOTHED LOCK
0 103 X-2149-672-1 SERVICE ASSY, OP (DAX-25A) 107 A-1177-201-A SERVO BOARD, COMPLETE
104 2-626-869-01 SCREW (M2X3), SERRATION #6 7-627-000-08 SCREW, PRECISION +P 1.7X2.2 TYPE 3
35
Ver. 1.2 SECTION 7
KEY
ELECTRICAL PARTS LIST
NOTE:
• Due to standardization, replacements in • Items marked “*” are not stocked since The components identified by
the parts list may be different from the they are seldom required for routine service. mark 0 or dotted line with mark
parts specified in the diagrams or the Some delay should be anticipated 0 are critical for safety.
components used on the set. when ordering these items. Replace only with part number
• -XX and -X mean standardized parts, so • SEMICONDUCTORS specified.
they may have some difference from the In each case, u : µ, for example:
original one. uA.. : µA.. uPA.. : µPA.. When indicating parts by reference
• RESISTORS uPB.. : µPB.. uPC.. : µPC.. uPD.. : µPD.. number, please include the board.
All resistors are in ohms. • CAPACITORS
• Abbreviation
METAL:Metal-film resistor. uF : µF
IND : Indian model
METAL OXIDE: Metal oxide-film resistor. • COILS
MX : Mexican model
F:nonflammable uH : µH
EA : Saudi Arabia model
RU : Russian model
KEY BOARD LCD901 1-802-535-11 DISPLAY PANEL, LIQUID CRYSTAL
********** (GT570/GT570S)
1-780-563-11 CONDUCTIVE BOARD, CONNECTION < DIODE >
< CAPACITOR > LED902 8-719-053-09 LED SML-310VTT86 (SOURCE) (GT527EE)

LED903 8-719-053-09 LED SML-310VTT86 (SEEK+/M >)
C971 1-135-834-11 CERAMIC CHIP 2.2uF 6.3V (GT527EE)
C980 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V LED904 8-719-053-09 LED SML-310VTT86 (MODE) (GT527EE)
C981 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V LED905 8-719-053-09 LED SML-310VTT86 (OFF) (GT527EE)
C982 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V LED906 8-719-053-09 LED SML-310VTT86 (ALBM –) (GT527EE)
C983 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
LED907 8-719-053-09 LED SML-310VTT86 (SEEK–/. m)
C984 1-125-891-11 CERAMIC CHIP 0.47uF 10% 10V (GT527EE)
LED908 8-719-053-09 LED SML-310VTT86 (ALBM +) (GT527EE)
< CONNECTOR > LED909 8-719-053-09 LED SML-310VTT86 (DSPL/SCRL) (GT527EE)
LED910 8-719-053-09 LED SML-310VTT86 (6/PAUSE) (GT527EE)
CN901 1-819-783-11 PLUG, CONNECTOR 16P LED911 8-719-053-09 LED SML-310VTT86 (5) (GT527EE)
< DIODE > LED912 8-719-053-09 LED SML-310VTT86 (4/SHUF) (GT527EE)

LED913 8-719-053-09 LED SML-310VTT86 (3/REP) (GT527EE)
D903 6-501-738-01 DIODE MAZ8062GMLS0 LED914 8-719-053-09 LED SML-310VTT86 (2) (GT527EE)
D904 6-501-738-01 DIODE MAZ8062GMLS0 LED915 8-719-053-09 LED SML-310VTT86 (1) (GT527EE)
D905 6-501-738-01 DIODE MAZ8062GMLS0 LED916 8-719-053-09 LED SML-310VTT86 (AF/TA/PTY) (GT527EE)
D906 6-501-738-01 DIODE MAZ8062GMLS0
D907 6-501-738-01 DIODE MAZ8062GMLS0 LED930 6-501-339-01 LED NESW505CT-AST (LCD BACK LIGHT-L)
LED931 6-501-339-01 LED NESW505CT-AST (LCD BACK LIGHT-R)
D908 6-501-738-01 DIODE MAZ8062GMLS0 LED943 8-719-053-09 LED SML-310VTT86
D909 6-501-738-01 DIODE MAZ8062GMLS0 (VOLUME ILLUMINATION) (GT527EE)
D911 6-501-782-01 DIODE MAZ8180GMLS0 LED946 6-501-547-01 LED CL-197HB1E-D-T
D981 6-501-738-01 DIODE MAZ8062GMLS0 (VOLUME ILLUMINATION) (GT570/GT570S)
D982 6-501-782-01 DIODE MAZ8180GMLS0 LED946 8-719-078-21 LED SML-310PTT86
(VOLUME ILLUMINATION) (GT527EE)
D984 6-501-817-01 DIODE MA2J1110GLS0
LED947 8-719-053-09 LED SML-310VTT86
< JUMPER RESISTOR > (VOLUME ILLUMINATION) (GT527EE)
LED948 8-719-053-09 LED SML-310VTT86
FB880 1-216-864-11 SHORT CHIP 0 (VOLUME ILLUMINATION) (GT527EE)
FB881 1-216-864-11 SHORT CHIP 0 LED949 6-501-547-01 LED CL-197HB1E-D-T
FB882 1-216-864-11 SHORT CHIP 0 (VOLUME ILLUMINATION) (GT570/GT570S)
LED949 8-719-078-21 LED SML-310PTT86
< IC > (VOLUME ILLUMINATION) (GT527EE)
LED950 8-719-053-09 LED SML-310VTT86
IC901 6-707-064-01 IC LC75876WH-US-E (VOLUME ILLUMINATION) (GT527EE)
IC971 6-600-629-01 IC RS-470 (IR)
LED951 6-501-547-01 LED CL-197HB1E-D-T
< JACK > (VOLUME ILLUMINATION) (GT570/GT570S)
LED951 8-719-078-21 LED SML-310PTT86
J901 1-820-833-11 JACK, SMALL TYPE (VERTICAL) (AUX) (VOLUME ILLUMINATION) (GT527EE)
LED952 6-501-547-01 LED CL-197HB1E-D-T (SOURCE)
< LIQUID CRYSTAL DISPLAY > (GT570/GT570S)
LED952 8-719-078-21 LED SML-310PTT86 (SOURCE) (GT527EE)
LCD901 1-802-534-11 DISPLAY PANEL, LIQUID CRYSTAL (GT527EE)
36
KEY
LED953 6-501-547-01 LED CL-197HB1E-D-T (SEEK+/M >) R912 1-216-821-11 METAL CHIP 1K 5% 1/10W
(GT570/GT570S) R914 1-216-822-11 METAL CHIP 1.2K 5% 1/10W
LED953 8-719-078-21 LED SML-310PTT86 (SEEK+/M >) R915 1-216-823-11 METAL CHIP 1.5K 5% 1/10W
(GT527EE) R916 1-216-824-11 METAL CHIP 1.8K 5% 1/10W
LED954 6-501-547-01 LED CL-197HB1E-D-T (MODE) R917 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
(GT570/GT570S)
LED954 8-719-078-21 LED SML-310PTT86 (MODE) (GT527EE) R921 1-216-030-00 RES-CHIP 160 5% 1/10W
LED955 6-501-547-01 LED CL-197HB1E-D-T (OFF) (GT570/GT570S) (GT527EE)
R922 1-216-030-00 RES-CHIP 160 5% 1/10W
LED955 8-719-078-21 LED SML-310PTT86 (OFF) (GT527EE) (GT527EE)
LED956 6-501-547-01 LED CL-197HB1E-D-T (ALBM –) R922 1-216-037-00 RES-CHIP 330 5% 1/10W
(GT570/GT570S) (GT570/GT570S)
LED956 8-719-078-21 LED SML-310PTT86 (ALBM –) (GT527EE) R923 1-216-031-00 RES-CHIP 180 5% 1/10W
LED957 6-501-547-01 LED CL-197HB1E-D-T (SEEK–/. m) (GT527EE)
(GT570/GT570S) R924 1-216-027-00 RES-CHIP 120 5% 1/10W
LED957 8-719-078-21 LED SML-310PTT86 (SEEK–/. m) (GT527EE)
(GT527EE)
R924 1-216-037-00 RES-CHIP 330 5% 1/10W
LED958 6-501-547-01 LED CL-197HB1E-D-T (ALBM +) (GT570/GT570S)
(GT570/GT570S) R925 1-216-030-00 RES-CHIP 160 5% 1/10W
LED958 8-719-078-21 LED SML-310PTT86 (ALBM +) (GT527EE) (GT527EE)
LED959 6-501-547-01 LED CL-197HB1E-D-T (DSPL/SCRL) R926 1-216-030-00 RES-CHIP 160 5% 1/10W
(GT570/GT570S) (GT527EE)
LED959 8-719-078-21 LED SML-310PTT86 (DSPL/SCRL) (GT527EE) R926 1-216-037-00 RES-CHIP 330 5% 1/10W
LED960 6-501-547-01 LED CL-197HB1E-D-T (6/PAUSE) (GT570/GT570S)
(GT570/GT570S) R927 1-216-031-00 RES-CHIP 180 5% 1/10W
(GT527EE)
LED960 8-719-078-21 LED
SML-310PTT86 (6/PAUSE) (GT527EE)
LED961 6-501-547-01 LED
CL-197HB1E-D-T (5) (GT570/GT570S) R928 1-216-027-00 RES-CHIP 120 5% 1/10W
LED961 8-719-078-21 LED
SML-310PTT86 (5) (GT527EE) (GT527EE)
LED962 6-501-547-01 LED
CL-197HB1E-D-T (4/SHUF) R928 1-216-037-00 RES-CHIP 330 5% 1/10W
(GT570/GT570S) (GT570/GT570S)
LED962 8-719-078-21 LED SML-310PTT86 (4/SHUF) (GT527EE) R929 1-216-030-00 RES-CHIP 160 5% 1/10W
(GT527EE)
LED963 6-501-547-01 LED CL-197HB1E-D-T (3/REP) R930 1-216-030-00 RES-CHIP 160 5% 1/10W
(GT570/GT570S) (GT527EE)
LED963 8-719-078-21 LED SML-310PTT86 (3/REP) (GT527EE) R930 1-216-037-00 RES-CHIP 330 5% 1/10W
LED964 6-501-547-01 LED CL-197HB1E-D-T (2) (GT570/GT570S) (GT570/GT570S)
LED964 8-719-078-21 LED SML-310PTT86 (2) (GT527EE)
LED965 6-501-547-01 LED CL-197HB1E-D-T (1) (GT570/GT570S) R931 1-216-031-00 RES-CHIP 180 5% 1/10W
(GT527EE)
LED965 8-719-078-21 LED
SML-310PTT86 (1) (GT527EE) R932 1-216-027-00 RES-CHIP 120 5% 1/10W
LED966 6-501-547-01 LED
CL-197HB1E-D-T (BTM) (GT570/GT570S) (GT527EE)
LED966 8-719-078-21 LED
SML-310PTT86 (AF/TA/PTY) (GT527EE) R932 1-216-037-00 RES-CHIP 330 5% 1/10W
LED993 6-501-547-01 LED
CL-197HB1E-D-T (GT570/GT570S)
(VOLUME ILLUMINATION) (GT570/GT570S) R933 1-216-033-00 RES-CHIP 220 5% 1/10W
LED993 8-719-078-21 LED SML-310PTT86 (GT527EE)
(VOLUME ILLUMINATION) (GT527EE) R934 1-216-029-00 RES-CHIP 150 5% 1/10W
(GT527EE)
< TRANSISTOR >
R934 1-216-041-00 RES-CHIP 470 5% 1/10W
Q901 8-729-027-44 TRANSISTOR DTC114TKA-T146 (GT570/GT570S)
Q919 6-551-856-01 TRANSISTOR LTC614TKFP8T146 (GT527EE) R935 1-216-027-00 RES-CHIP 120 5% 1/10W
Q920 6-551-856-01 TRANSISTOR LTC614TKFP8T146 (GT527EE) (GT527EE)
R936 1-216-027-00 RES-CHIP 120 5% 1/10W
< RESISTOR > (GT527EE)
R936 1-216-037-00 RES-CHIP 330 5% 1/10W
R901 1-216-820-11 METAL CHIP 820 5% 1/10W (GT570/GT570S)
R902 1-216-821-11 METAL CHIP 1K 5% 1/10W R937 1-216-025-11 RES-CHIP 100 5% 1/10W
R903 1-216-821-11 METAL CHIP 1K 5% 1/10W (GT527EE)
R904 1-216-822-11 METAL CHIP 1.2K 5% 1/10W
R905 1-216-823-11 METAL CHIP 1.5K 5% 1/10W R938 1-216-027-00 RES-CHIP 120 5% 1/10W
(GT527EE)
R907 1-216-825-11 METAL CHIP 2.2K 5% 1/10W (GT570/GT570S)
R910 1-216-820-11 METAL CHIP 820 5% 1/10W (GT527EE)
R911 1-216-821-11 METAL CHIP 1K 5% 1/10W R940 1-216-030-00 RES-CHIP 160 5% 1/10W
(GT527EE)
37
KEY
R940 1-216-045-00 RES-CHIP 680 5% 1/10W R961 1-216-031-00 RES-CHIP 180 5% 1/10W
(GT570/GT570S) (GT527EE)
(GT527EE) (GT527EE)
(GT527EE) (GT570/GT570S)
R942 1-216-045-00 RES-CHIP 680 5% 1/10W R969 1-216-824-11 METAL CHIP 1.8K 5% 1/10W
(GT570/GT570S) R970 1-216-811-11 METAL CHIP 150 5% 1/10W
R943 1-216-029-00 RES-CHIP 150 5% 1/10W (GT527EE)
(GT527EE)
R970 1-216-813-11 METAL CHIP 220 5% 1/10W
R944 1-216-030-00 RES-CHIP 160 5% 1/10W (GT570/GT570S)
(GT527EE) R971 1-216-809-11 METAL CHIP 100 5% 1/10W
R944 1-216-037-00 RES-CHIP 330 5% 1/10W (GT527EE)
R945 1-216-031-00 RES-CHIP 180 5% 1/10W (GT570/GT570S)
R946 1-216-027-00 RES-CHIP 120 5% 1/10W (GT527EE)
R946 1-216-037-00 RES-CHIP 330 5% 1/10W (GT570/GT570S)
(GT570/GT570S)
R977 1-216-809-11 METAL CHIP 100 5% 1/10W
R947 1-216-029-00 RES-CHIP 150 5% 1/10W R978 1-216-813-11 METAL CHIP 220 5% 1/10W
(GT527EE) R979 1-216-821-11 METAL CHIP 1K 5% 1/10W
R948 1-216-045-00 RES-CHIP 680 5% 1/10W
R949 1-216-031-00 RES-CHIP 180 5% 1/10W R985 1-216-857-11 METAL CHIP 1M 5% 1/10W
(GT570/GT570S) R994 1-216-864-11 SHORT CHIP 0 (GT570/GT570S)
(GT527EE) (GT570/GT570S)
R952 1-216-030-00 RES-CHIP 160 5% 1/10W
(GT527EE) < ROTARY ENCODER >
R952 1-216-037-00 RES-CHIP 330 5% 1/10W
(GT570/GT570S) RE901 1-479-902-21 ENCODER, ROTARY
R953 1-216-031-00 RES-CHIP 180 5% 1/10W (VOLUME CONTROL DIAL/SELECT BUTTON)
(GT527EE)
< SWITCH >
R954 1-216-027-00 RES-CHIP 120 5% 1/10W
(GT527EE) S901 1-786-653-21 SWITCH, TACTILE (OFF)
R954 1-216-037-00 RES-CHIP 330 5% 1/10W S902 1-786-653-21 SWITCH, TACTILE (SOURCE)
(GT570/GT570S) S903 1-786-653-21 SWITCH, TACTILE (SEEK+/M >)
R955 1-216-029-00 RES-CHIP 150 5% 1/10W S904 1-786-653-21 SWITCH, TACTILE (MODE)
(GT527EE) S905 1-786-653-21 SWITCH, TACTILE (ALBM –)
R956 1-216-030-00 RES-CHIP 160 5% 1/10W
(GT527EE) S906 1-786-653-21 SWITCH, TACTILE (SEEK–/. m)
R956 1-216-045-00 RES-CHIP 680 5% 1/10W S907 1-786-653-21 SWITCH, TACTILE (ALBM +)
(GT570/GT570S) S908 1-786-653-21 SWITCH, TACTILE (DSPL/SCRL)
S909 1-786-653-21 SWITCH, TACTILE (6/PAUSE)
R957 1-216-031-00 RES-CHIP 180 5% 1/10W S910 1-786-653-21 SWITCH, TACTILE (5)
(GT527EE)
R958 1-216-027-00 RES-CHIP 120 5% 1/10W S911 1-786-653-21 SWITCH, TACTILE (4/SHUF)
(GT527EE) S912 1-786-653-21 SWITCH, TACTILE (3/REP)
R958 1-216-041-00 RES-CHIP 470 5% 1/10W S913 1-786-653-21 SWITCH, TACTILE (2)
(GT570/GT570S) S914 1-786-653-21 SWITCH, TACTILE (1)
R959 1-216-030-00 RES-CHIP 160 5% 1/10W S915 1-786-653-21 SWITCH, TACTILE (AF/TA/PTY) (GT527EE)
(GT527EE)
R960 1-216-030-00 RES-CHIP 160 5% 1/10W S915 1-786-653-21 SWITCH, TACTILE (BTM) (GT570/GT570S)
(GT527EE) *************************************************************
R960 1-216-037-00 RES-CHIP 330 5% 1/10W

(GT570/GT570S)
38
Ver. 1.2
MAIN
A-1312-911-A MAIN BOARD, COMPLETE (RU) C312 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25V
A-1312-912-A MAIN BOARD, COMPLETE (E,IND,MX) C313 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
A-1312-914-A MAIN BOARD, COMPLETE (EA) C314 1-124-261-00 ELECT 10uF 20% 50V
********************* C315 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V
C316 1-124-261-00 ELECT 10uF 20% 50V
7-685-134-19 SCREW +P 2.6X8 TYPE2 NON-SLIT
7-685-794-09 SCREW +PTT 2.6X10 (S) C317 1-124-257-00 ELECT 2.2uF 20% 50V
C318 1-162-923-11 CERAMIC CHIP 47PF 5% 50V
< CAPACITOR > C319 1-216-864-11 SHORT CHIP 0
C1 1-126-963-11 ELECT 4.7uF 20% 50V C321 1-126-960-11 ELECT 1uF 20% 50V
(GT527EE)
C2 1-126-947-11 ELECT 47uF 20% 35V C323 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25V
C3 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C324 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25V
(GT570/GT570S) C327 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16V
C7 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C330 1-216-864-11 SHORT CHIP 0
C8 1-162-967-11 CERAMIC CHIP 0.0033uF 10% 50V C331 1-216-864-11 SHORT CHIP 0
C9 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C360 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
(GT527EE)
C363 1-115-871-11 ELECT 1uF 20% 50V
C51 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C364 1-115-871-11 ELECT 1uF 20% 50V
(GT527EE) C401 1-124-584-00 ELECT 100uF 20% 10V
(GT527EE) C403 1-126-176-11 ELECT 220uF 20% 10V
(GT527EE) C405 1-124-248-00 ELECT 22uF 20% 25V
C54 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C410 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
(GT527EE) C411 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
C55 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V (GT570/GT570S)
(GT527EE) C412 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
(GT527EE) C414 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C57 1-162-917-11 CERAMIC CHIP 15PF 5% 50V C415 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C58 1-162-959-11 CERAMIC CHIP 330PF 5% 50V C418 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
C61 1-126-947-11 ELECT 47uF 20% 35V
(GT527EE) C421 1-126-964-11 ELECT 10uF 20% 50V
(GT527EE) C423 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
C431 1-126-964-11 ELECT 10uF 20% 50V
C63 1-162-927-11 CERAMIC CHIP 100PF 5% 50V C432 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C103 1-165-319-11 CERAMIC CHIP 0.1uF 50V C441 1-126-964-11 ELECT 10uF 20% 50V
C446 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
C116 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V C451 1-126-964-11 ELECT 10uF 20% 50V
C117 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V (GT527EE)
C300 1-126-960-11 ELECT 1uF 20% 50V C452 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C461 1-126-964-11 ELECT 10uF 20% 50V
C303 1-128-551-11 ELECT 22uF 20% 63V C465 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
C306 1-126-964-11 ELECT 10uF 20% 50V C471 1-126-964-11 ELECT 10uF 20% 50V
C472 1-165-908-11 CERAMIC CHIP 1uF 10% 10V
C307 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C480 1-136-159-00 FILM 0.033uF 5% 50V
C308 1-126-964-11 ELECT 10uF 20% 50V C481 1-136-159-00 FILM 0.033uF 5% 50V
39
MAIN
C483 1-162-968-11 CERAMIC CHIP 0.0047uF 10% 50V D305 6-500-522-01 DIODE 10EDB40-TA1B2
C485 1-104-665-11 ELECT 100uF 20% 25V D307 6-500-522-01 DIODE 10EDB40-TA1B2
C494 1-216-864-11 SHORT CHIP 0 D310 6-500-522-01 DIODE 10EDB40-TA1B2

C501 1-128-057-11 ELECT 330uF 20% 6.3V D311 6-500-522-01 DIODE 10EDB40-TA1B2
C503 1-124-584-00 ELECT 100uF 20% 10V D400 6-501-656-01 DIODE LBAT54ALT1G
C504 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V D491 6-501-817-01 DIODE MA2J1110GLS0
C505 1-124-584-00 ELECT 100uF 20% 10V D493 6-501-654-01 DIODE LBAT54CLT1G
C506 1-165-908-11 CERAMIC CHIP 1uF 10% 10V D494 6-501-656-01 DIODE LBAT54ALT1G
C507 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V D501 8-719-050-37 DIODE M1MA152WA-T1
C508 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V D502 8-719-060-48 DIODE RB751V-40TE-17
C509 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V D511 6-501-654-01 DIODE LBAT54CLT1G
C510 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V D602 6-501-782-01 DIODE MAZ8180GMLS0
C511 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V D603 8-719-422-67 DIODE MA8062-H
C515 1-162-916-11 CERAMIC CHIP 12PF 5% 50V D606 8-719-072-70 DIODE MA2ZD14001S0
C516 1-162-917-11 CERAMIC CHIP 15PF 5% 50V D607 6-501-571-01 DIODE 1N5404-C311-3
C523 1-162-927-11 CERAMIC CHIP 100PF 5% 50V D702 6-501-782-01 DIODE MAZ8180GMLS0
C600 1-126-941-11 ELECT 470uF 20% 25V
C601 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V < FERRITE BEAD >
C602 1-165-319-11 CERAMIC CHIP 0.1uF 50V FB401 1-414-595-11 INDUCTOR, FERRITE BEAD
C701 1-112-302-11 ELECT 3300uF 20% 16V FB402 1-216-864-11 SHORT CHIP 0
C702 1-126-160-11 ELECT 1uF 20% 50V FB403 1-216-864-11 SHORT CHIP 0
C704 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25V FB404 1-216-295-11 SHORT CHIP 0
FB407 1-216-295-11 SHORT CHIP 0
< CONNECTOR > FB408 1-216-864-11 SHORT CHIP 0 (GT570/GT570S)
FB408 1-469-876-11 INDUCTOR, FERRITE BEAD (GT527EE)
CN300 1-774-701-21 PIN, CONNECTOR 16P
CN350 1-820-611-11 CONNECTOR, BOARD TO BOARD 28P < IC >
* CN410 1-564-506-11 PLUG, CONNECTOR 3P (GT570/GT570S)
* CN702 1-770-524-31 CONNECTOR, FFC/FPC 17P IC50 6-803-747-01 IC TDA7333013TR (GT527EE)
CNJ400 1-580-907-41 PLUG, CONNECTOR 8P (BUS CONTROL IN) IC300 6-705-359-02 IC TDA8588AJ/N2/R1
IC401 6-710-065-01 IC BD3442FS-E2
< DIODE > IC501 6-807-655-01 IC MB90F045PF-G-9060-SPE1
IC502 6-711-653-01 IC S-1206B33-U3T1G
D2 6-501-734-01 DIODE MAZ8056GMLS0
D101 6-501-743-01 DIODE MAZ8068GMLS0 IC601 6-703-884-01 IC BA8271F-E2
D102 6-501-782-01 DIODE MAZ8180GMLS0 IC602 8-759-659-13 IC PST3428UL
D103 6-501-782-01 DIODE MAZ8180GMLS0
D104 6-501-782-01 DIODE MAZ8180GMLS0 < JACK >
D105 6-501-743-01 DIODE MAZ8068GMLS0 J1 1-815-185-13 JACK (ANTENNA)

D106 6-501-743-01 DIODE MAZ8068GMLS0 J370 1-566-822-41 JACK (REMOTE IN)
D107 6-501-743-01 DIODE MAZ8068GMLS0 J451 1-774-700-41 JACK, PIN 6P (BUS AUDIO IN,
D108 6-501-743-01 DIODE MAZ8068GMLS0 REAR/SUB AUDIO OUT,FRONT AUDIO OUT)
D109 6-501-743-01 DIODE MAZ8068GMLS0 (GT527EE)
J451 1-774-700-41 JACK, PIN 6P (BUS AUDIO IN,
D110 6-501-743-01 DIODE MAZ8068GMLS0 REAR AUDIO OUT,FRONT AUDIO OUT)
D114 6-501-743-01 DIODE MAZ8068GMLS0 (GT570/GT570S)
D115 6-501-743-01 DIODE MAZ8068GMLS0
D116 6-501-743-01 DIODE MAZ8068GMLS0 < JUMPER RESISTOR >
D301 6-500-522-01 DIODE 10EDB40-TA1B2
JC3 1-216-864-11 SHORT CHIP 0
D302 6-500-522-01 DIODE 10EDB40-TA1B2 JC9 1-216-295-11 SHORT CHIP 0 (GT527EE)
D303 6-500-522-01 DIODE 10EDB40-TA1B2 JC53 1-216-864-11 SHORT CHIP 0
D304 6-500-522-01 DIODE 10EDB40-TA1B2 JC90 1-216-296-11 SHORT CHIP 0 (GT527EE)
40
MAIN
JC300 1-216-296-11 SHORT CHIP 0 Q605 8-729-027-43 TRANSISTOR DTC114EKA-T146
JC301 1-216-296-11 SHORT CHIP 0 Q701 8-729-620-07 TRANSISTOR 2SC3052EF-T1-LEF (GT527EE)
JC302 1-216-296-11 SHORT CHIP 0 Q702 8-729-620-07 TRANSISTOR 2SC3052EF-T1-LEF
JC303 1-216-864-11 SHORT CHIP 0 (GT527EE)
JC304 1-216-864-11 SHORT CHIP 0 (GT570/GT570S) < RESISTOR >
JC305 1-216-296-11 SHORT CHIP 0 (GT570/GT570S) R1 1-216-809-11 METAL CHIP 100 5% 1/10W
JC400 1-216-295-11 SHORT CHIP 0 R2 1-216-839-11 METAL CHIP 33K 5% 1/10W
JC430 1-216-296-11 SHORT CHIP 0 (GT527EE) R4 1-216-839-11 METAL CHIP 33K 5% 1/10W
R5 1-216-843-11 METAL CHIP 68K 5% 1/10W
JC490 1-216-296-11 SHORT CHIP 0
JC491 1-216-296-11 SHORT CHIP 0 R6 1-414-595-11 INDUCTOR, FERRITE BEAD
R9 1-216-843-11 METAL CHIP 68K 5% 1/10W
JC511 1-216-864-11 SHORT CHIP 0
JC512 1-216-864-11 SHORT CHIP 0 R11 1-216-864-11 SHORT CHIP 0 (GT527EE)
R13 1-414-595-11 INDUCTOR, FERRITE BEAD
JC522 1-216-295-11 SHORT CHIP 0 R14 1-216-864-11 SHORT CHIP 0 (GT527EE)
JC600 1-216-864-11 SHORT CHIP 0
JC602 1-216-296-11 SHORT CHIP 0 R53 1-216-803-11 METAL CHIP 33 5% 1/10W
(GT527EE)
JC603 1-216-296-11 SHORT CHIP 0 R54 1-414-595-11 INDUCTOR, FERRITE BEAD (GT527EE)
R55 1-216-797-11 METAL CHIP 10 5% 1/10W
< COIL > (GT527EE)
R57 1-216-833-11 METAL CHIP 10K 5% 1/10W
L1 1-500-245-11 INDUCTOR, FERRITE BEAD (GT527EE)
L2 1-216-809-11 METAL CHIP 100 5% 1/10W R58 1-216-821-11 METAL CHIP 1K 5% 1/10W
(GT527EE) (GT527EE)
L3 1-216-809-11 METAL CHIP 100 5% 1/10W
(GT527EE) R144 1-249-413-11 CARBON 470 5% 1/4W
L4 1-469-844-11 INDUCTOR 2.2uH R146 1-249-413-11 CARBON 470 5% 1/4W
L101 1-410-509-11 INDUCTOR 10uH R301 1-216-811-11 METAL CHIP 150 5% 1/10W
R302 1-216-841-11 METAL CHIP 47K 5% 1/10W
L300 1-456-617-11 COIL, CHOKE R351 1-216-845-11 METAL CHIP 100K 5% 1/10W
L301 1-216-864-11 SHORT CHIP 0
L302 1-216-864-11 SHORT CHIP 0 R355 1-216-834-11 METAL CHIP 12K 5% 1/10W
L303 1-216-864-11 SHORT CHIP 0 R356 1-216-834-11 METAL CHIP 12K 5% 1/10W
L500 1-469-844-11 INDUCTOR 2.2uH R357 1-414-595-11 INDUCTOR, FERRITE BEAD
R358 1-414-595-11 INDUCTOR, FERRITE BEAD
< TRANSISTOR > R359 1-500-329-21 INDUCTOR, FERRITE BEAD
Q1 8-729-038-28 TRANSISTOR RT1N441C-TP-1 (GT527EE) R361 1-216-821-11 METAL CHIP 1K 5% 1/10W

Q3 8-729-106-68 TRANSISTOR 2SD1615A-GP R370 1-216-809-11 METAL CHIP 100 5% 1/10W
Q50 8-729-026-49 TRANSISTOR 2SA1037AK-T146-R (GT527EE) R371 1-216-809-11 METAL CHIP 100 5% 1/10W
Q420 6-551-856-01 TRANSISTOR LTC614TKFP8T146 R400 1-216-296-11 SHORT CHIP 0
Q430 6-551-856-01 TRANSISTOR LTC614TKFP8T146 R401 1-216-821-11 METAL CHIP 1K 5% 1/10W

Q450 6-551-856-01 TRANSISTOR LTC614TKFP8T146 (GT527EE) R407 1-216-864-11 SHORT CHIP 0
Q470 6-551-856-01 TRANSISTOR LTC614TKFP8T146 (GT570/GT570S)
Q491 8-729-027-23 TRANSISTOR DTA114EKA-T146 R416 1-216-821-11 METAL CHIP 1K 5% 1/10W
R417 1-216-833-11 METAL CHIP 10K 5% 1/10W
Q492 8-729-027-43 TRANSISTOR DTC114EKA-T146
Q501 8-729-027-23 TRANSISTOR DTA114EKA-T146 R418 1-216-821-11 METAL CHIP 1K 5% 1/10W
Q589 8-729-027-43 TRANSISTOR DTC114EKA-T146 R419 1-216-833-11 METAL CHIP 10K 5% 1/10W
Q590 8-729-027-23 TRANSISTOR DTA114EKA-T146 R421 1-216-813-11 METAL CHIP 220 5% 1/10W
Q600 8-729-047-76 TRANSISTOR FMC2A-T148 R422 1-216-833-11 METAL CHIP 10K 5% 1/10W
R431 1-216-813-11 METAL CHIP 220 5% 1/10W
Q601 8-729-027-23 TRANSISTOR DTA114EKA-T146
41
MAIN
R432 1-216-833-11 METAL CHIP 10K 5% 1/10W R528 1-216-833-11 METAL CHIP 10K 5% 1/10W
R433 1-218-883-11 METAL CHIP 33K 0.5% 1/10W R529 1-216-845-11 METAL CHIP 100K 5% 1/10W
R441 1-216-813-11 METAL CHIP 220 5% 1/10W R530 1-216-845-11 METAL CHIP 100K 5% 1/10W
(GT527EE)
R533 1-216-845-11 METAL CHIP 100K 5% 1/10W
R453 1-216-864-11 SHORT CHIP 0 R534 1-216-845-11 METAL CHIP 100K 5% 1/10W
R454 1-216-864-11 SHORT CHIP 0 R535 1-216-809-11 METAL CHIP 100 5% 1/10W
R455 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R536 1-216-811-11 METAL CHIP 150 5% 1/10W
(GT527EE) (GT570/GT570S)
R471 1-216-813-11 METAL CHIP 220 5% 1/10W R539 1-216-809-11 METAL CHIP 100 5% 1/10W
R472 1-216-833-11 METAL CHIP 10K 5% 1/10W R540 1-216-809-11 METAL CHIP 100 5% 1/10W
R474 1-216-864-11 SHORT CHIP 0 R542 1-216-845-11 METAL CHIP 100K 5% 1/10W
R480 1-216-827-11 METAL CHIP 3.3K 5% 1/10W (GT527EE)
R481 1-216-827-11 METAL CHIP 3.3K 5% 1/10W R543 1-216-845-11 METAL CHIP 100K 5% 1/10W
R484 1-216-821-11 METAL CHIP 1K 5% 1/10W R547 1-216-827-11 METAL CHIP 3.3K 5% 1/10W
R491 1-216-805-11 METAL CHIP 47 5% 1/10W R548 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R494 1-216-825-11 METAL CHIP 2.2K 5% 1/10W R549 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R501 1-216-845-11 METAL CHIP 100K 5% 1/10W (GT570/GT570S)
(GT570/GT570S) R551 1-216-864-11 SHORT CHIP 0
R503 1-216-845-11 METAL CHIP 100K 5% 1/10W
(GT570/GT570S) R555 1-216-833-11 METAL CHIP 10K 5% 1/10W
R556 1-216-833-11 METAL CHIP 10K 5% 1/10W
R504 1-216-845-11 METAL CHIP 100K 5% 1/10W R557 1-216-809-11 METAL CHIP 100 5% 1/10W
(EA)
(GT527EE) (GT527EE)
(E,CH,IND,MX) (GT570/GT570S)
R572 1-216-845-11 METAL CHIP 100K 5% 1/10W
(GT570/GT570S) (GT570/GT570S)
R512 1-216-845-11 METAL CHIP 100K 5% 1/10W
R513 1-216-809-11 METAL CHIP 100 5% 1/10W (GT570/GT570S)
(GT527EE)
R516 1-216-809-11 METAL CHIP 100 5% 1/10W (GT527EE)
R602 1-216-851-11 METAL CHIP 330K 5% 1/10W
R525 1-216-845-11 METAL CHIP 100K 5% 1/10W
42
Ver. 1.3
MAIN SERVO SUB
R605 1-216-809-11 METAL CHIP 100 5% 1/10W R202 1-216-815-11 METAL CHIP 330 5% 1/10W
R607 1-216-821-11 METAL CHIP 1K 5% 1/10W R202 1-216-823-11 METAL CHIP 1.5K 5% 1/10W
R608 1-216-829-11 METAL CHIP 4.7K 5% 1/10W (GT570/GT570S)
R610 1-216-809-11 METAL CHIP 100 5% 1/10W
< SWITCH >
R611 1-216-809-11 METAL CHIP 100 5% 1/10W
R701 1-216-821-11 METAL CHIP 1K 5% 1/10W S201 1-786-653-21 SWITCH, TACTILE (Z)
R702 1-216-841-11 METAL CHIP 47K 5% 1/10W *************************************************************
(GT527EE)
R703 1-216-833-11 METAL CHIP 10K 5% 1/10W MISCELLANEOUS
(GT527EE) ***************
R704 1-216-833-11 METAL CHIP 10K 5% 1/10W
(GT527EE) 3 1-834-507-11 CABLE, FLEXIBLE FLAT (17 CORE) (CN202)
12 1-831-838-11 CORD (WITH CONNECTOR) (ISO) (POWER)
R705 1-249-425-11 CARBON 4.7K 5% 1/4W (GT527EE)
R706 1-216-841-11 METAL CHIP 47K 5% 1/10W 12 1-833-762-11 CONNECTION CORD FOR AUTOMOBILE
R707 1-216-841-11 METAL CHIP 47K 5% 1/10W (POWER) (for Maruti Suzuki:Gasoline Car)
R708 1-216-829-11 METAL CHIP 4.7K 5% 1/10W 12 1-833-974-21 CONNECTION CORD FOR AUTOMOBILE
(POWER) (GT570/GT570S)
< SWITCH > 12 1-834-307-11 CONNECTION CORD FOR AUTOMOBILE
(POWER) (for Maruti Suzuki:Diesel Car)
S102 1-786-458-11 SWITCH, PUSH (1 KEY)
(FRONT PANEL DETECT) 13 1-833-887-11 CONNECTION CORD (RCA) (SUB OUT (MONO))
S103 1-786-826-11 SWITCH, TACTILE (RESET) (GT570/GT570S)
S501 1-571-478-11 SWITCH, SLIDE (FREQUENCY SELECT) 0 103 X-2149-672-1 SERVICE ASSY, OP (DAX-25A)
(E,IND,MX) FU601 1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) 10A
*************************************************************
< THERMISTOR (POSITIVE) >
ACCESSORIES
TH400 1-803-350-21 THERMISTOR, POSITIVE ************
< TUNER UNIT > 1-479-077-13 REMOTE COMMANDER (RM-X151)

2-548-729-01 LID, BATTERY CASE (for RM-X151)
TU1 A-3220-960-B TUNER UNIT (TUX-032) (GT570/GT570S) 3-217-494-21 MANUAL, INSTRUCTION (RUSSIAN,
TU1 A-3220-961-B TUNER UNIT (TUX-032) (GT527EE) UKRAINIAN) (GT527EE)
3-217-494-31 MANUAL, INSTRUCTION (ENGLISH,SPANISH,
< VIBRATOR > PERSIAN) (E,IND,MX)
3-217-494-51 MANUAL, INSTRUCTION (ENGLISH,ARABIC)
X50 1-813-532-11 VIBRATOR, CRYSTAL (8.664MHz) (GT527EE) (EA)
X500 1-813-524-21 VIBRATOR, CERAMIC (18.432MHz)
X501 1-767-317-11 VIBRATOR, CRYSTAL (32.768kHz) 3-217-595-21 MANUAL, INSTRUCTION, INSTALL (RUSSIAN,
************************************************************* UKRAINIAN) (GT527EE)
3-217-595-31 MANUAL, INSTRUCTION, INSTALL (ENGLISH,
A-1177-201-A SERVO BOARD, COMPLETE SPANISH,PERSIAN) (E,IND,MX)
********************** 3-217-595-51 MANUAL, INSTRUCTION, INSTALL (ENGLISH,
************************************************************* ARABIC) (EA)
X-2149-228-2 CASE ASSY (for FRONT PANEL)
SUB BOARD *************************************************************
**********
< CONNECTOR >
CN201 1-819-782-11 SOCKET, CONNECTOR 16P
< DIODE >
LED201 6-501-547-01 LED CL-197HB1E-D-T (DISC IN)

(GT570/GT570S)
LED201 8-719-078-21 LED SML-310PTT86 (DISC IN) (GT527EE)
LED202 6-501-547-01 LED CL-197HB1E-D-T (Z) (GT570/GT570S)
LED202 8-719-078-21 LED SML-310PTT86 (Z) (GT527EE)
< RESISTOR >
R201 1-216-812-11 METAL CHIP 180 5% 1/10W

(GT527EE)
R201 1-216-815-11 METAL CHIP 330 5% 1/10W
(GT570/GT570S)
43
Ver. 1.3
Ref. No. Part No. Description Remark

PARTS FOR INSTALLATION AND CONNECTIONS
**************************************
151 X-2179-431-1 FRAME ASSY, FITTING

152 1-833-974-21 CONNECTION CORD FOR AUTOMOBILE
(POWER) (GT570/GT570S)
153 3-246-471-01 KEY (FRAME)
154 3-209-713-01 COLLAR
154 3-255-785-02 COLLAR (1 DIN) (for Maruti Suzuki)
155 X-3381-154-1 SCREW ASSY (BS4), FITTING

156 3-349-410-11 BUSHING
157 3-934-325-01 SCREW, +K (5X8) TAPPING
158 1-465-459-31 ADAPTOR, ANTENNA (GT527EE)
159 1-831-838-11 CORD (WITH CONNECTOR) (ISO) (POWER)
(GT527EE)
151 152 153
×2
154 155
156 157
×4
158 159
44
MEMO
45
REVISION HISTORY
Clicking the version allows you to jump to the revised page.

Also, clicking the version at the top of the revised page allows you to jump to the next revised page.
Ver. Date Description of Revision

1.0 2007. 08 New
1.1 2007. 09 Deletion of Indian model of CDX-GT570. (ENG-07007)
1.2 2007. 10 Deletion of Chinese model of CDX-GT570. (ENG-07008)
1.3 2007. 12 Maruti Suzuki model addition of CDX-GT570 (Indian).
46

Sony CDX Gt527ee Gt570 Gt570s

Uploaded by

Copyright:

Available Formats

Sony CDX Gt527ee Gt570 Gt570s

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Sony CDX Gt527ee Gt570 Gt570s

Uploaded by

Copyright:

Available Formats

CDX-GT527EE/GT570/

FM/MW/LW COMPACT DISC PLAYER

9-887-812-04 Sony Corporation

MW (CDX-GT570/GT570S) SERVICE NOTES

MPEG Layer-3 audio coding technology and

Design and specifications are subject to change without semi-fixed resistor

SAFETY-RELATED COMPONENT WARNING!!

COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE

This compact disc player is classified as a CLASS 1 LASER

: LEAD FREE MARK

1. SERVICE NOTE ........................................................ 5

4. DIAGNOSIS FUNCTION ........................................ 17

7. ELECTRICAL PARTS LIST .................................. 36

NOTE FOR REPLACEMENT OF THE SERVO BOARD

NOTE FOR REPLACEMENT OF THE AUX JACK (J901)

• Location of controls and basic operations (CDX-GT570/GT570S)

Location of controls and basic operations

*1 RCA pin cord (not supplied)

SUB OUT (MONO) FRONT REMOTE

Blue/white striped 2 Black

Connection diagram Diagrama de conexión

3-1. SUB (AUX) PANEL ASSY

3-2. CD MECHANISM BLOCK

3-3. MAIN BOARD 3-4. SERVO BOARD

3-5. CHASSIS (T) SUB ASSY

3-6. ROLLER ARM ASSY

3-7. CHASSIS (OP) ASSY

3-8. CHUCKING ARM SUB ASSY

3-9. SLED MOTOR ASSY

3-10. OPTICAL PICK-UP SECTION

3-11. OPTICAL PICK-UP

Note: Follow the disassembly procedure in the numerical order given.

3-1. SUB (AUX) PANEL ASSY

4 flexible flat cable (17 core)

5 sub (AUX) panel assy

3-2. CD MECHANISM BLOCK

3-3. MAIN BOARD

3-4. SERVO BOARD

WHT 2 toothed lock screw

1 Remove the eleven solders. 5 SERVO board

4 optical pick-up (16 core)

3-5. CHASSIS (T) SUB ASSY

2 two precision screws

4 chassis (T) sub assy

3-6. ROLLER ARM ASSY

5 roller arm assy

3-7. CHASSIS (OP) ASSY

6 chassis (OP) assy

1 tension spring (KF)

7 coil spring (damper) (natural)

8 coil spring (damper) (blue)

3-8. CHUCKING ARM SUB ASSY

3 chucking arm sub assy

Note: Be careful not to touch the turn table.

3-9. SLED MOTOR ASSY

2 three serration screws

3 sled motor assy

Note for Assembly

three serration screws