CDXR6550 1706729786

CDX-R5515X/R5610/R6550
SERVICE MANUAL US Model

Canadian Model
Ver. 1.1 2005.07 CDX-R5515X
AEP Model
UK Model
CDX-R6550
E Model
CDX-R5610
Photo: CDX-R6550
• The tuner and CD sections have no adjustments.

Model Name Using Similar Mechanism NEW
AUDIO POWER SPECIFICATIONS (US MODEL) CD Drive Mechanism Type MG-611TA-186//K
POWER OUTPUT AND TOTAL HARMONIC DISTORTION Optical Pick-up Name KSS1000E
23.2 watts per channel minimum continuous average power into
4 ohms, 4 channels driven from 20 Hz to 20 kHz with no more
than 5% total harmonic distortion.
SPECIFICATIONS
CD player section AM (CDX-R5610)
Signal-to-noise ratio 120 dB Tuning range 531 – 1,602 kHz (at 9 kHz step)
Frequency response 10 – 20,000 Hz 530 – 1,710 kHz (at 10 kHz step)
Wow and flutter Below measurable limit AM tuning interval 9 kHz/10 kHz switchable
Aerial terminal External aerial connector
Tuner section Intermediate frequency 10.7 MHz/450 kHz
FM Sensitivity 30 µV
Tuning range CDX-R5515X:
87.5 – 107.9 MHz MW/LW (CDX-R6550)
CDX-R5610: Tuning range MW: 531 – 1,602 kHz
87.5 – 108.0 MHz (at 50 kHz step) LW: 153 – 279 kHz
87.5 – 107.9 MHz (at 200 kHz step) Antenna terminal External antenna connector
CDX-R6550: Intermediate frequency 10.7 MHz/450 kHz
87.5 – 108 MHz Sensitivity MW: 30 µV
Antenna terminal External antenna connector LW: 40 µV
Intermediate frequency 10.7 MHz/450 kHz
Usable sensitivity 9 dBf Power amplifier section
Selectivity 75 dB at 400 kHz Outputs Speaker outputs
Signal-to-noise ratio 67 dB (stereo), (sure seal connectors)
69 dB (mono) Speaker impedance 4 – 8 ohms
Harmonic distortion at 1 kHz Maximum power output 52 W × 4 (at 4 ohms) (CDX-R5515X/R5610)
0.5% (stereo), 50 W × 4 (at 4 ohms) (CDX-R6550)
0.3% (mono)
Separation 35 dB at 1 kHz – Continued on next page –
Frequency response 30 – 15,000 Hz
AM (CDX-R5515X)
Tuning range 530 – 1,710 kHz
FM/AM COMPACT DISC PLAYER

Antenna terminal External antenna connector
Intermediate frequency 10.7 MHz/450 kHz
Sensitivity 30 µV
CDX-R5515X/R5610
FM/MW/LW COMPACT DISC PLAYER
CDX-R6550
9-879-368-02 Sony Corporation

2005G04-1 e Vehicle Group
© 2005.07 Published by Sony Engineering Corporation
1
CDX-R5515X/R5610/R6550
General
Outputs Audio outputs terminal (front, sub/rear switchable) CAUTION
Subwoofer output terminal (mono) (CDX-R5515X) Use of controls or adjustments or performance of procedures
Power antenna relay control terminal other than those specified herein may result in hazardous
Power amplifier control terminal
Inputs Telephone ATT control terminal
radiation exposure.
Illumination control terminal
BUS control input terminal
BUS audio input terminal (CDX-R5610/R6550)
If the optical pick-up block is defective, please replace the whole
Remote controller input terminal optical pick-up block.
Antenna input terminal Never turn the semi-fixed resistor located at the side of optical
Tone controls CDX-R5610/R6550: pick-up block.
Low: ±10 dB at 60 Hz (XPLOD)
Mid: ±10 dB at 1 kHz (XPLOD)
High: ±10 dB at 10 kHz (XPLOD)
Power requirements 12 V DC car battery optical pick-up
(negative ground)
Dimensions Approx. 178 × 50 × 182 mm
(7 1/8 × 2 × 7 1/4 in.) (w/h/d)
Mounting dimensions Approx. 182 × 53 × 161 mm
(7 1/4 × 2 1/8 × 6 3/8 in.) (w/h/d)
Mass Approx. 1.2 kg
(2 lb. 10 oz.)
Supplied accessories Parts for installation and connections (1 set)
Front panel case (1)
Card remote commander RM-X151
US and foreign patents licensed from Dolby Laboratories.
Note
This unit cannot be connected to a digital preamplifier or an equalizer which is Sony
BUS system compatible.
Design and specifications are subject to change without

notice.
semi-fixed resistor
• CDX-R5610/R6550 model
SERVICE NOTES
NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK

OR BASE UNIT
The laser diode in the optical pick-up block may suffer electrostatic
breakdown because of the potential difference generated by the This label is located on the bottom of the chassis.
charged electrostatic load, etc. on clothing and the human body.
During repair, pay attention to electrostatic breakdown and also use
the procedure in the printed matter which is included in the repair
parts.
The flexible board is easily damaged and should be handled with
care.
NOTES ON LASER DIODE EMISSION CHECK SAFETY-RELATED COMPONENT WARNING!!

The laser beam on this model is concentrated so as to be focused on
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINE
the disc reflective surface by the objective lens in the optical pick-
WITH MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN
up block. Therefore, when checking the laser diode emission, ob-
THE PARTS LIST ARE CRITICAL TO SAFE OPERATION.
serve from more than 30 cm away from the objective lens. REPLACE THESE COMPONENTS WITH SONY PARTS WHOSE
PART NUMBERS APPEAR AS SHOWN IN THIS MANUAL OR
Notes on Chip Component Replacement IN SUPPLEMENTS PUBLISHED BY SONY.
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
damaged by heat. ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!!
TEST DISCS
This set can playback CD-R and CD-ROM discs. The following LES COMPOSANTS IDENTIFIÉS PAR UNE MARQUE 0 SUR LES
test discs should be used to check the capability: DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈCES SONY
CD-R test disc TCD-R082LMT (Part No. J-2502-063-1) DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
CD-RW test disc TCD-W082L (Part No. J-2502-063-2) DANS LES SUPPLÉMENTS PUBLIÉS PAR SONY.
2
CDX-R5515X/R5610/R6550
• CD Playback: z UNLEADED SOLDER

You can play CD-DA (also containing CD TEXT*1), CD-R/CD- Boards requiring use of unleaded solder are printed with the lead
RW (MP3 files also containing Multi Session and ATRAC CD free mark (LF) indicating the solder contains no lead.
(ATRAC3 and ATRAC3plus format). (Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size)
Type of discs Label on the disc
: LEAD FREE MARK
Unleaded solder has the following characteristics.
CD-DA • Unleaded solder melts at a temperature about 40 °C higher
than ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350 °C.
MP3 Caution: The printed pattern (copper foil) may peel away if
the heated tip is applied for too long, so be careful!
ATRAC CD • Strong viscosity
Unleaded solder is more viscou-s (sticky, less prone to flow)
than ordinary solder so use caution not to let solder bridges
occur such as on IC pins, etc.
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
*1 A CD TEXT disc is a CD-DA that includes information such as also be added to ordinary solder.
disc, artist and track name.
EXTENSION CABLE AND SERVICE POSITION

When repairing or servicing this set, connect the jig (extension cable)
as shown below.
• Connect the MAIN board (CN350) and the SERVO board (CN2)
with the extension cable (Part No. J-2502-076-1).
MAIN BOARD J-2502-076-1

CN350
SERVO BOARD
CN2
3
CDX-R5515X/R5610/R6550
TABLE OF CONTENTS
1. GENERAL
Location of Controls ................................................................ 5
Connections ............................................................................. 6
2. DISASSEMBLY
2-1. Sub Panel (LCD) Assy ...................................................... 12
2-2. CD Mechanism Block ....................................................... 12
2-3. Main Board ....................................................................... 13
2-4. Chassis (T) Sub Assy ........................................................ 13
2-5. Roller Arm Assy ................................................................ 14
2-6. Chassis (OP) Assy ............................................................. 14
2-7. Optical Pick-up ................................................................. 15
2-8. SL Motor Assy (M902) ..................................................... 15
2-9. LE Motor Assy (M903) ..................................................... 16
2-10. Servo Board ....................................................................... 16
2-11. Front Back Panel (LCD) ................................................... 17
2-12. Key Board ......................................................................... 17
2-13. Display Section ................................................................. 18
2-14. Spring (M) ......................................................................... 18
2-15. Spring (S) .......................................................................... 19
3. DIAGRAMS
3-1. Block Diagram –CD Section– ........................................... 21
3-2. Block Diagram –Main Section– ........................................ 22
3-3. Block Diagram –Display Section– .................................... 23
3-4. Circuit Boards Location .................................................... 24
3-5. Printed Wiring Boards –CD Mechanism Section– ............ 25
3-6. Schematic Diagram –CD Mechanism Section (1/2)– ....... 26
3-7. Schematic Diagram –CD Mechanism Section (2/2)– ....... 27
3-8. Printed Wiring Board –Main Section– .............................. 28
3-9. Schematic Diagram –Main Section (1/2)– ........................ 29
3-10. Schematic Diagram –Main Section (2/2)– ........................ 30
3-11. Printed Wiring Board –Key Section– ................................ 31
3-12. Schematic Diagram –Key Section– ................................... 32
3-13. Printed Wiring Board –Display Section– .......................... 33
3-14. Schematic Diagram –Display Section– ............................. 34
3-15. Printed Wiring Board –Preset Section– ............................. 35
3-16. Schematic Diagram –Preset Section– ............................... 35
4. EXPLODED VIEWS
4-1. Main Section ..................................................................... 42
4-2. Front Panel Section ........................................................... 43
4-3. CD Mechanism Section (1) ............................................... 44
5. ELECTRICAL PARTS LIST ......................................... 48
4
CDX-R5515X/R5610/R6550
SECTION 1
GENERAL This section is extracted
from instruction manual.
• LOCATION OF CONTROLS
• CDX-R5515X
Location of controls and basic operations

Main unit G DSO button 2 The following buttons on the card remote
To select the DSO mode (1, 2, 3 or OFF). commander have also different buttons/functions
1 2 34 5 6 7 8 9 The larger the number, the more enhanced from the unit.
the effect. wa < (.)/, (>) buttons
ATT OFF
H OFF button To control radio/CD, the same as (SEEK)
OPEN/CLOSE +/– on the unit. (For details of other
To power off/stop the source.
DSPL DSO operations, see “With the card remote
I SEEK +/– button commander” on each pages.)
SEL EQ3 SEEK Radio:
To tune in stations automatically (press); find ws VOL +/– button
a station manually (press and hold). To adjust volume.
SOURCE MODE
- GP/DISC +
1 2
REP
3
SHUF
4
BBE MP
5 6 BTM SENS
CAT
LIST
CD: wd M (+)/m (–) buttons
To skip tracks (press); skip tracks
continuously (press, then press again within To control CD, the same as (1)/(2) –/+ on
CDX-R5515X about 1 second and hold); fast-forward/ the unit. (For details of other operations, see
“With the card remote commander” on each
0 qa qs qd qf qg qh qj qk reverse a track (press and hold).
pages.)
J (front panel release) button 4
wf SCRL button 8
OPEN/CLOSE shutter opened K SOURCE button To scroll the display item.
To power on/change the source (Radio/CD/ wg Number buttons
ql w; MD*1).
To receive stored stations (press); store
L MODE button 8, 11 stations (press and hold).
ATT OFF To select the radio band (FM/AM)/select the
unit*2. *1 When an MD changer is connected.
OPEN/CLOSE *2 When a CD/MD changer is connected.
M RESET button (located behind the front *3 When an MP3/ATRAC CD is played and a changer
DSPL DSO SEEK
panel) 4 is not connected. If the changer is connected, the
operation is different, see page 11.
SEL EQ3 N Number buttons
Note
SOURCE MODE
-
1
GP/DISC +
2
REP
3
SHUF
4
BBE MP
5 6 AF/TA
BTM
SENS
LIST
PTY Radio: If the unit is turned off and the display disappears, it
To receive stored stations (press); store cannot be operated with the card remote commander
stations (press and hold). unless (SOURCE) on the unit is pressed, or a disc is
CD/MD*1: inserted to activate the unit first.
Card remote commander Refer to the pages listed for details. The (1)/(2): GP*3/DISC*2 –/+ Tip
corresponding buttons on the card remote To skip groups (press); skip groups For details on how to replace the battery, see
RM-X151 commander control the same functions as those continuously (press and hold). “Replacing the lithium battery of the card remote
on the unit. (3): REP 8 commander” on page 14.
8 OFF ATT
2 A Volume +/– button
(4): SHUF 8
(5): BBE MP 3
qa 4 To adjust volume. To activate the BBE MP function, to set
SOURCE SEL MODE
wa qs B ATT (attenuate) button “BBEMP-ON” during playback on this unit.

To attenuate the sound. To cancel, press To cancel, set “BBEMP-OFF.”
+ again. O BTM button 8
wd C DSPL (display) button 4, 8, 12 To start the BTM function.
– To change display items. P SENS button
3 DSPL SCRL wf D SEL (select) button 4, 9, 10, 12 To improve weak reception: LOCAL/
To select items. MONO.
1 2 3
4 5 6
wg E Display window Q LIST/CAT button 9, 11
To list up.
F EQ3 (equalizer) button 2, 9
+ To select an equalizer type (XPLOD, R Receptor for the card remote
ws VOL
– VOCAL, CLUB, JAZZ, NEW AGE, ROCK, commander
CUSTOM or OFF). S Disc slot 5
T Z (eject) button 6
6 7
• CDX-R5610

Main unit G DSO button 2 S Receptor for the card remote
To select the DSO mode (1, 2, 3 or OFF). commander
1 2 34 5 6 7 8 9 The larger the number, the more enhanced
T Disc slot 5
the effect.
H OFF button U Z (eject) button 6
ATT OFF
OPEN/CLOSE
To power off/stop the source. The following buttons on the card remote
DSPL DSO
I SEEK +/– button commander have also different buttons/functions
SEL EQ3 SEEK Radio: from the unit.
To tune in stations automatically (press); find ws < (.)/, (>) buttons
a station manually (press and hold). To control radio/CD, the same as (SEEK)
SOURCE MODE
- GP/DISC +
1 2
REP
3
SHUF
4
BBE MP
5 6 BTM SENS LIST
CD: +/– on the unit. (For details of other
To skip tracks (press); skip tracks operations, see “With the card remote
continuously (press, then press again within commander” on each pages.)
CDX-R5610 about 1 second and hold); fast-forward/
0 qa qs qd qf qg qh qj qk ql reverse a track (press and hold). wd VOL +/– button
To adjust volume.
J (front panel release) button 4
OPEN/CLOSE shutter opened wf M (+)/m (–) buttons
K SOURCE button To control CD, the same as (1)/(2) –/+ on
w; wa To power on/change the source (Radio/CD/ the unit. (For details of other operations, see
MD*1). “With the card remote commander” on each
L MODE button 8, 11 pages.)
ATT OFF
To select the radio band (FM/AM)/select the wg SCRL (scroll) button 8
OPEN/CLOSE unit*2. To scroll the display item.
DSPL DSO SEEK M RESET button (located behind the front wh Number buttons
panel) 4 To receive stored stations (press); store
SEL EQ3
N Number buttons stations (press and hold).
- GP/DISC + REP SHUF BBE MP BTM LIST
SOURCE MODE 1 2 3 4 5 6 AF/TA SENS PTY
Radio:
To receive stored stations (press); store *1 When an MD changer is connected.
*2 When a CD/MD changer is connected.
stations (press and hold). *3 When an MP3/ATRAC CD is played and a changer
CD/MD*1:
Card remote commander Refer to the pages listed for details. The
(1)/(2): GP*3/DISC*2 –/+
is not connected. If the changer is connected, the
corresponding buttons on the card remote operation is different, see page 11.
RM-X151 commander control the same functions as those To skip groups (press); skip groups
Note
on the unit. continuously (press and hold). If the unit is turned off and the display disappears, it
8 2 A Volume +/– button
(3): REP 8 cannot be operated with the card remote commander
OFF ATT
(4): SHUF 8 unless (SOURCE) on the unit is pressed, or a disc is
qa 4 To adjust volume. (5): BBE MP 2 inserted to activate the unit first.
SOURCE SEL MODE
To activate the BBE MP function, to set
ws qs B ATT (attenuate) button “BBEMP-ON” during playback on this unit.
Tip
To attenuate the sound. To cancel, press For details on how to replace the battery, see
To cancel, set “BBEMP-OFF.” “Replacing the lithium battery of the card remote
+ again. commander” on page 14.
O Frequency select switch (located on
wf C DSPL (display) button 4, 8, 10 the bottom of the unit)
– To change display items. See “Frequency Select switch” in the
3 DSPL SCRL wg D SEL (select) button 4, 9, 10, 12 supplied installation/connections manual.
To select items. P BTM button 8
1 2 3
4 5 6
wh E Display window To start the BTM function.
F EQ3 (equalizer) button 2, 9 Q SENS button
+ To select an equalizer type (XPLOD, To improve weak reception: LOCAL/
wd VOL
– VOCAL, CLUB, JAZZ, NEW AGE, ROCK, MONO.
CUSTOM or OFF). R LIST button 10
To list up.
6 7
5
CDX-R5515X/R5610/R6550
• CDX-R6550

Main unit G DSO button 2 S Disc slot 5
To select the DSO mode (1, 2, 3 or OFF).
The larger the number, the more enhanced T Z (eject) button 5
1 2 34 5 6 7 8 9 the effect. The following buttons on the card remote
H OFF button commander have also different buttons/functions
ATT OFF
To power off/stop the source. from the unit.
OPEN/CLOSE
DSPL DSO
I SEEK +/– button wa < (.)/, (>) buttons
Radio: To control radio/CD, the same as (SEEK)
SEL EQ3 SEEK
To tune in stations automatically (press); find +/– on the unit. (For details of other
a station manually (press and hold). operations, see “With the card remote
CD: commander” on each pages.)
SOURCE MODE 1 2 3 4 5 6 AF/TA SENS PTY To skip tracks (press); skip tracks ws VOL +/– button
continuously (press, then press again within To adjust volume.
CDX-R6550 about 1 second and hold); fast-forward/
reverse a track (press and hold). wd M (+)/m (–) buttons
0 qa qs qd qf qg qh qj qk To control CD, the same as (1)/(2) –/+ on
J (front panel release) button 4 the unit. (For details of other operations, see
OPEN/CLOSE shutter opened “With the card remote commander” on each
K SOURCE button
pages.)
ql w; To power on/change the source (Radio/CD/
MD*1). wf SCRL button 8
L MODE button 8, 12 To scroll the display item.
ATT OFF
To select the radio band (FM/MW/LW)/ wg Number buttons
OPEN/CLOSE select the unit*2. To receive stored stations (press); store
M RESET button (located behind the front stations (press and hold).
DSPL DSO SEEK
panel) 4
SEL EQ3
*1 When an MD changer is connected.
N Number buttons *2 When a CD/MD changer is connected.
SOURCE MODE 1 2 3 4 5 6 AF/TA SENS PTY
Radio: *3 When an MP3/ATRAC CD is played and a changer

is not connected. If the changer is connected, the
To receive stored stations (press); store operation is different, see page 12.
stations (press and hold).
CD/MD*1: Note
Card remote commander Refer to the pages listed for details. The (1)/(2): GP*3/DISC*2 –/+ If the unit is turned off and the display disappears, it
corresponding buttons on the card remote To skip groups (press); skip groups cannot be operated with the card remote commander
RM-X151 commander control the same functions as those unless (SOURCE) on the unit is pressed, or a disc is
continuously (press and hold). inserted to activate the unit first.
on the unit. (3): REP 8
8 OFF ATT
2 A Volume +/– button (4): SHUF 8 Tip
For details on how to replace the battery, see
qa 4 To adjust volume. (5): BBE MP 2 “Replacing the lithium battery of the card remote
SOURCE SEL MODE To activate the BBE MP function, to set commander” on page 15.
wa qs B ATT (attenuate) button “BBEMP-ON” during playback on this unit.
To attenuate the sound. To cancel, press To cancel, set “BBEMP-OFF.”
+ again.
O AF (Alternative Frequencies)/TA
wd C DSPL (display) button 4, 8, 12 (Traffic Announcement) button 9
– To change display items. To set AF and TA/TP in RDS.
3 DSPL SCRL wf D SEL (select) button 4, 11, 12 P SENS/BTM button 8
To select items. To improve weak reception: LOCAL/MONO
1 2 3
4 5 6
wg E Display window (press); start the BTM function (press and
hold).
F EQ3 (equalizer) button 2, 11
Q PTY (Programme Type)/LIST button
+ To select an equalizer type (XPLOD,
ws VOL 10
– VOCAL, CLUB, JAZZ, NEW AGE, ROCK,
CUSTOM or OFF). To select PTY in RDS; list up.
R Receptor for the card remote
commander
6 7
• CONNECTIONS
• CDX-R5515X
Connection example (2)

Notes (2-A)
A • Be sure to connect the ground lead before connecting the
amplifier.
AUDIO OUT FRONT • The alarm will only sound if the built-in amplifier is used.
Tip (2-B- )
For connecting two or more CD/MD changers, the source
selector XA-C30 (optional) is necessary.
AUDIO OUT REAR

Exemple de raccordement (2)
Remarques (2-A)
• Raccordez d’abord le câble de mise à la masse avant de
raccorder l’amplificateur.
• L’alarme est émise uniquement lorsque l’amplificateur intégré
est utilisé.
Conseil (2-B- )
Dans le cas du raccordement de deux changeurs de CD/MD ou
B BUS AUDIO IN plus, le sélecteur de source XA-C30 (en option) est requis.
BUS CONTROL IN
BUS AUDIO IN
Source selector*
Sélecteur de source*
XA-C30
* not supplied
BUS CONTROL IN non fourni
6
CDX-R5515X/R5610/R6550
• CDX-R5610
• CDX-R6550
Connection example (2)

A Notes (2-A)
• Be sure to connect the earth lead before connecting the
amplifier.
• The alarm will only sound if the built-in amplifier is used.
AUDIO OUT FRONT
Tip (2-B- )
For connecting two or more CD/MD changers, the source
selector XA-C30 (optional) is necessary.
Anschlussbeispiel (2)
AUDIO OUT REAR Hinweise (2-A)
• Schließen Sie unbedingt zuerst das Massekabel an, bevor Sie
den Verstärker anschließen.
• Der Warnton wird nur ausgegeben, wenn der integrierte
Verstärker verwendet wird.
Tipp (2-B- )
Zum Anschließen von zwei oder mehr CD/MD-Wechslern wird
der gesondert erhältliche Signalquellenwähler XA-C30 benötigt.
Exemple de raccordement (2)

B BUS AUDIO IN Remarques (2-A)
• Raccordez d’abord le câble de mise à la masse avant de
connecter l’amplificateur.
• L’alarme est émise uniquement lorsque l’amplificateur intégré
est utilisé.
Conseil (2-B- )
Dans le cas du raccordement de deux changeurs de CD/MD
BUS CONTROL IN ou plus, le sélecteur de source XA-C30 (en option) est
indispensable.
Esempio di collegamento (2)

Note (2-A)
• Assicurarsi di collegare il cavo di terra prima di collegare
l’apparecchio all’amplificatore.
• Tale segnale viene emesso solo se è in uso l’amplificatore
BUS AUDIO IN incorporato.
Suggerimento (2-B- )
Source selector* Per collegare due o più cambia CD/MD, si deve utilizzare il
Signalquellenwähler* selettore di fonte XA-C30 (opzionale).
Sélecteur de source*
Selettore di fonte*
Geluidsbronkiezer*
XA-C30
Voorbeeldaansluitingen (2)
BUS CONTROL IN Opmerkingen (2-A)
* not supplied • Sluit eerst de aarddraad aan voordat u de versterker aansluit.
nicht mitgeliefert • U hoort de pieptoon alleen als de ingebouwde versterker wordt
non fourni gebruikt.
non in dotazione
niet bijgeleverd Tip (2-B- )
Om twee of meer CD/MD-wisselaars aan te sluiten, hebt u de
geluidsbronkiezer XA-C30 (optioneel) nodig.
7
CDX-R5515X/R5610/R6550
• CDX-R5515X
*1
Source selector
(not supplied)
Sélecteur de source Supplied with the CD/MD changer
(non fourni) Fourni avec le changeur de CD/MD
Supplied with XA-C30 XA-C30

Fourni avec le XA-C30
*1
AUDIO OUT
REMOTE
FRONT
IN
*3
BUS AUDIO IN L
from car antenna

à partir de l’antenne de la voiture
AUDIO OUT Fuse (10 A) BUS
REAR*2 Fusible (10 A) CONTROL IN
*1 RCA pin cord (not supplied)
*2 AUDIO OUT can be switched SUB or
Blue/white striped 2 REAR. For details, see the Operating
AMP REM Rayé bleu/blanc Instructions manual.
3 *3 Insert with the cord upwards.
Max. supply current 0.3 A Black
Courant max. fourni 0,3 A Noir *1 Cordon à broche RCA (non fourni)
1 *2 AUDIO OUT peut être commuté sur SUB
White ou REAR. Pour obtenir plus de détails,
Blanc reportez-vous au mode d’emploi.
Left Blue *3 Insérez avec le câble vers le haut.
ANT REM
Gauche Bleu
White/black striped 2
Max. supply current 0.1 A
Rayé blanc/noir
Courant max. fourni 0,1 A
Gray Light blue
Gris Bleu ciel ATT
Right 4
Droit
Gray/black striped
Rayé gris/noir Orange/white striped
Rayé orange/blanc ILLUMINATION
Green 5
Vert
Left
Gauche Red
Green/black striped Rouge
Rayé vert/noir 6
Purple
Mauve Yellow
Right Jaune
Droit 7
Purple/black striped
Rayé mauve/noir
Notes on the control and power supply leads Remarques sur les câbles de commande et d’alimentation
• The power antenna control lead (blue) supplies +12 V DC • Le câble de commande d’antenne électrique (bleu) fournit une
Connection diagram (3) when you turn on the tuner.
• When your car has built-in FM/AM antenna in the rear/side
Schéma de raccordement (3) alimentation de + 12 V CC lorsque vous mettez la radio sous
tension.
1 To a metal surface of the car glass, connect the power antenna control lead (blue) or the 1 À un point métallique de la voiture • Lorsque votre voiture est équipée d’une antenne FM/AM
First connect the black ground lead, then connect the accessory power input lead (red) to the power terminal of the Branchez d’abord le fil de masse noir et, ensuite, les fils intégrée dans la vitre arrière/latérale, raccordez le câble de
orange/white striped, yellow, and red power input leads. existing antenna booster. For details, consult your dealer. d’entrée d’alimentation rayé orange/blanc, jaune, et rouge. commande d’antenne (bleu) ou l’entrée d’alimentation des
• A power antenna without a relay box cannot be used with this accessoires (rouge) à la borne d’alimentation de l’amplificateur
2 To the power antenna control lead or power unit. 2 Vers le câble de commande d’antenne d’antenne existant. Pour plus de détails, consultez votre
supply lead of antenna booster amplifier Memory hold connection
électrique ou le câble d’alimentation de détaillant.
Notes When the yellow power input lead is connected, power will l’amplificateur d’antenne • Une antenne électrique sans boîtier de relais ne peut pas être
• It is not necessary to connect this lead if there is no power always be supplied to the memory circuit even when the ignition Remarques utilisée avec cet appareil.
antenna or antenna booster, or with a manually-operated switch is turned off. • Il n’est pas nécessaire de raccorder ce câble s’il n'y a pas Raccordement pour la conservation de la mémoire
telescopic antenna. d’antenne électrique ni d’amplificateur d’antenne, ou avec Lorsque le câble d’entrée d’alimentation jaune est raccordé, le
• When your car has a built-in FM/AM antenna in the rear/ Notes on speaker connection
une antenne télescopique manuelle. circuit de la mémoire est alimenté en permanence même si la clé
side glass, see “Notes on the control and power supply • Before connecting the speakers, turn the unit off.
• Si votre voiture est équipée d’une antenne FM/AM de contact est sur la position d’arrêt.
leads.” • Use speakers with an impedance of 4 to 8 ohms, and with
intégrée dans la vitre arrière/latérale, voir « Remarques
adequate power handling capacities to avoid its damage. Remarques sur le raccordement des haut-parleurs
3 To AMP REMOTE IN of an optional power sur les câbles de commande et d’alimentation ».
• Do not connect the speaker terminals to the car chassis, or • Avant de raccorder les haut-parleurs, mettez l’appareil hors
amplifier connect the terminals of the right speakers with those of the 3 Au niveau de AMP REMOTE IN de tension.
This connection is only for amplifiers. Connecting any other left speaker. l’amplificateur de puissance en option • Utilisez des haut-parleurs ayant une impédance de 4 à 8 ohms
system may damage the unit. • Do not connect the ground lead of this unit to the negative (–) Ce raccordement s’applique uniquement aux amplificateurs. avec une capacité électrique adéquate pour éviter de les
4 To the interface cable of a car telephone terminal of the speaker. Le branchement de tout autre système risque endommager.
• Do not attempt to connect the speakers in parallel. d’endommager l’appareil. • Ne raccordez pas les bornes du système de haut-parleurs au
5 To a car’s illumination signal • Connect only passive speakers. Connecting active speakers châssis de la voiture et ne raccordez pas les bornes des haut-
Be sure to connect the black ground lead to a metal surface (with built-in amplifiers) to the speaker terminals may damage 4 Vers le cordon de liaison d’un téléphone de parleurs droit à celles du haut-parleur gauche.
of the car first. the unit. voiture • Ne raccordez pas le câble de mise à la masse de cet appareil
6 To the +12 V power terminal which is • To avoid a malfunction, do not use the built-in speaker leads 5 Vers le connecteur du signal d’éclairage de à la borne négative (–) du haut-parleur.
installed in your car if the unit shares a common negative (–) • N’essayez pas de raccorder les haut-parleurs en parallèle.
energized in the accessory position of the lead for the right and left speakers.
la voiture • Raccordez uniquement des haut-parleurs passifs. Le
ignition key switch Raccordez d’abord le fil de masse noir à un point métallique
• Do not connect the unit’s speaker leads to each other. raccordement de haut-parleurs actifs (avec amplificateurs
Notes du véhicule.
Note on connection intégrés) aux bornes des haut-parleurs peut endommager
• If there is no accessory position, connect to the +12 V
If speaker and amplifier are not connected correctly, “FAILURE”
6 À la borne +12 V qui est alimentée quand la l’appareil.
power (battery) terminal which is energized at all times. clé de contact est sur la position accessoires • Pour éviter tout problème de fonctionnement, n’utilisez pas les
appears in the display. In this case, make sure the speaker and
Be sure to connect the black ground lead to a metal Remarques câbles des haut-parleurs intégrés installés dans votre voiture si
amplifier are connected correctly.
surface of the car first. • S’il n’y a pas de position accessoires, raccordez la borne l’appareil partage un câble négatif commun (–) pour les haut-
• When your car has a built-in FM/AM antenna in the rear/ d’alimentation (batterie) +12 V qui est alimentée en parleurs droit et gauche.
side glass, see “Notes on the control and power supply permanence. Raccordez d’abord le câble de mise à la • Ne raccordez pas entre eux les cordons des haut-parleurs de
leads.” masse noir à un point métallique du véhicule. l’appareil.
7 To the +12 V power terminal which is • Si votre voiture est équipée d’une antenne FM/AM Remarque sur le raccordement
energized at all times intégrée dans la vitre arrière/latérale, voir « Remarques Si les haut-parleurs et l’amplificateur ne sont pas raccordés
Be sure to connect the black ground lead to a metal surface sur les câbles de commande et d’alimentation ». correctement, le message « FAILURE » s’affiche. Dans ce cas,
of the car first. 7 À la borne +12 V qui est alimentée en assurez-vous que les haut-parleurs et l’amplificateur sont bien
raccordés.
permanence
Raccordez d’abord le câble de mise à la masse noir à un
point métallique du véhicule.
8
CDX-R5515X/R5610/R6550
• CDX-R5610
9
CDX-R5515X/R5610/R6550
• CDX-R6550
Supplied with XA-C30 *1 Note for the aerial connecting *1 Remarque sur le raccordement de *1 Opmerking bij de antenne-aansluiting
Mit dem XA-C30 geliefert If your car aerial is an ISO (International l’antenne Indien uw auto is uitgerust met een
Fourni avec le XA-C30 Organisation for Standardisation) type, Si votre antenne de voiture est de type antenne van het type ISO (International
*2 In dotazione con il modello XA-C30 Source selector
use the supplied adaptor 2 to connect ISO (Organisation internationale de Organisation for Standardization),
Geleverd met de XA-C30 it. First connect the car aerial to the normalisation), utilisez l’adaptateur fourni moet u die aansluiten met behulp
(not supplied) supplied adaptor, then connect it to the 2 pour la raccorder. Raccordez d’abord van de bijgeleverde adapter 2. Sluit
Signalquellenwähler aerial jack of the master unit. l’antenne de voiture à l’adaptateur fourni eerst de auto-antenne aan op de
(nicht mitgeliefert) Supplied with the CD/MD changer
Mit dem CD/MD-Wechsler geliefert *2 RCA pin cord (not supplied) et, ensuite, à la prise d’antenne de bijgeleverde adapter en vervolgens de
Sélecteur de source *3 AUDIO OUT can be switched SUB or l’appareil principal. antennestekker op het hoofdtoestel.
(non fourni) Fourni avec le changeur de CD/MD
REAR. For details, see the Operating *2 Cordon à broche RCA (non fourni) *2 Tulpstekkersnoer (niet bijgeleverd)
Selettore di fonte In dotazione con il cambia CD/MD 3 3
Instructions manual. * AUDIO OUT peut être commuté sur SUB * AUDIO OUT kan worden ingesteld
(non in dotazione) Geleverd met de CD/MD-wisselaar *4 Insert with the cord upwards. ou REAR. Pour obtenir plus de détails, op SUB of REAR. Raadpleeg de
Geluidsbronkiezer reportez-vous au mode d’emploi. gebruiksaanwijzing voor meer informatie.
(niet bijgeleverd) *1 Hinweis zum Anschließen der Antenne *4 Insérez avec le câble vers le haut. *4 Plaatsen met het snoer naar boven.
Wenn Ihre Fahrzeugantenne der
ISO-Norm (ISO = International *1 Nota per il collegamento dell’antenna
XA-C30
2 Organization for Standardization Se l’antenna dell’auto è di tipo
* - Internationale Normungsgemeinschaft) ISO (International Organization for
AUDIO OUT entspricht, schließen Sie sie mithilfe des Standardization), utilizzare l’adattatore
REMOTE
FRONT mitgelieferten Adapters 2 an. Verbinden 2 in dotazione per collegarla. Collegare
IN Sie zuerst die Fahrzeugantenne mit dem prima l’antenna della macchina
mitgelieferten Adapter und verbinden Sie all’adattatore in dotazione, quindi
*4 diesen dann mit der Antennenbuchse collegarla alla presa dell’antenna
2 L des Hauptgeräts. dell’apparecchio principale.
*1 from car aerial *2 Cinchkabel (nicht mitgeliefert) *2 Cavo a piedini RCA (non in dotazione)
von Autoantenne R *3 AUDIO OUT kann zwischen SUB *3 AUDIO OUT può essere impostato
de l’antenne de la voiture und REAR umgeschaltet werden. su SUB o su REAR. Per ulteriori
dall’antenna dell’auto Näheres hierzu finden Sie in der informazioni, consultare il manuale di
van een auto-antenne Bedienungsanleitung. istruzioni per l’uso.
Fuse (10 A) *4 Mit dem Kabel nach oben einsetzen. *4 Inserire con il cavo rivolto verso l’alto.
BUS AUDIO IN
Sicherung (10 A)
Fusible (10 A) BUS
AUDIO OUT REAR*3 Fusibile (10 A) CONTROL IN
Max. supply current 0.3 A Zekering (10 A)
max. Versorgungsstrom 0,3 A Blue/white striped
Courant d’alimentation maximum 0,3 A Blauweiß gestreift 3 1 3 5 7
Alimentazione massima fornita 0,3 A Rayé bleu/blanc
Max. voedingsstroom 0,3 A Rigato blu e bianco from the car’s speaker connector
AMP REM Blauw/wit gestreept vom Lautsprecheranschluss des Fahrzeugs
du connecteur de haut-parleur de la voiture
dal connettore del diffusore dell’auto
van de autoluidsprekerstekker
2 4 6 8
Light blue
Speaker, Rear, Right Speaker, Front, Left
Hellblau 5 7 Lautsprecher hinten rechts Lautsprecher vorne links
Bleu ciel
from the car’s power connector 1 + Haut-parleur, arrière, droit 5 + Haut-parleur, avant, gauche
Azzurro Purple White
vom Stromanschluss des Fahrzeugs Diffusore, posteriore, destro Diffusore, anteriore, sinistro
ATT Lichtblauw Violett Weiß
du connecteur d’alimentation de la voiture Luidspreker, achter, rechts Luidspreker, voor, links
Mauve Blanc
dal connettore di alimentazione dell’auto Viola Speaker, Rear, Right Bianco Speaker, Front, Left
van de autovoedingsstekker Paars Lautsprecher hinten rechts Wit Lautsprecher vorne links
2 – Haut-parleur, arrière, droit 6 – Haut-parleur, avant, gauche
4 6 8 Diffusore, posteriore, destro Diffusore, anteriore, sinistro
Luidspreker, achter, rechts Luidspreker, voor, links
See “Power connection diagram” on the reverse side for details.
Yellow continuous power supply Red switched power supply Speaker, Front, Right Speaker, Rear, Left
Näheres dazu finden Sie im „Stromanschlussdiagramm“. Blättern Gelb permanente Stromversorgung Rot geschaltete Stromversorgung Lautsprecher vorne rechts Lautsprecher hinten links
Sie dazu bitte um. 4 Jaune alimentation continue 7 Rouge alimentation commutée 3 + Haut-parleur, avant, droit 7 + Haut-parleur, arrière, gauche
Voir le « Schéma de raccordement d’alimentation » au verso pour Giallo alimentazione continua Rosso alimentazione commutata Grey Diffusore, anteriore, destro Green Diffusore, posteriore, sinistro
plus de détails. Geel continu voeding Rood geschakelde voeding Grau Luidspreker, voor, rechts Grün Luidspreker, achter, links
Gris Vert
Per ulteriori informazioni, vedere “Diagramma dei collegamenti di Blue power aerial control Black earth Speaker, Front, Right Speaker, Rear, Left
Grigio Verde
alimentazione” che si trova sul retro. Blau Motorantennensteuerung Schwarz Masse Lautsprecher vorne rechts Lautsprecher hinten links
Grijs Groen
Zie "Voedingsaansluitschema" op de achterkant voor meer details. 5 Bleu antenne électrique 8 Noir masse 4 – Haut-parleur, avant, droit 8 – Haut-parleur, arrière, gauche
Blu comando dell’antenna elettrica Nero terra Diffusore, anteriore, destro Diffusore, posteriore, sinistro
Blauw automatische antenne Zwart aarding Luidspreker, voor, rechts Luidspreker, achter, links
Orange/White switched illumination power supply Positions 1, 2 and 3 do not have pins. Negative polarity positions 2, 4, 6, and 8 have striped leads.
Orangeweiß geschaltete An Position 1, 2 und 3 befinden sich keine Stifte. An den negativ gepolten Positionen 2, 4, 6 und 8 befinden sich gestreifte Adern.
gestreift Beleuchtungsstromversorgung Les positions 1, 2 et 3 ne comportent pas de broches. Les positions de polarité négative 2, 4, 6 et 8 sont dotées de cordons rayés.
Rayé orange/ alimentation de l’éclairage Le posizioni 1, 2 e 3 non hanno piedini. Le posizioni a polarità negativa 2, 4, 6 e 8 hanno cavi rigati.
De posities 1, 2 en 3 hebben geen pins. De posities voor negatieve polariteit (2, 4, 6 en 8) hebben gestreepte kabels.
6 blanc commuté
Arancione/ alimentazione illuminazione
bianco commutata
Oranje/wit geschakelde voeding voor
verlichting
Connection diagram (3) Anschlussdiagramm (3) Schémas de raccordement (3) Schema di collegamento (3) Aansluitschema (3)
A To AMP REMOTE IN of an optional power A An AMP REMOTE IN des gesondert A Au niveau du AMP REMOTE IN d’un A A AMP REMOTE IN di un amplificatore di A Naar AMP REMOTE IN van een optionele
amplifier erhältlichen Endverstärkers amplificateur de puissance facultatif potenza opzionale eindversterker
This connection is only for amplifiers. Connecting any other Dieser Anschluss ist ausschließlich für Verstärker gedacht. Ce raccordement existe seulement pour les amplificateurs. Questo collegamento è riservato esclusivamente agli Deze aansluiting is alleen bedoeld voor versterkers. Door
system may damage the unit. Schließen Sie nichts anderes daran an. Andernfalls kann Le raccordement à tout autre système peut endommager amplificatori. Non collegare un tipo di sistema diverso onde een ander systeem aan te sluiten kan het apparaat worden
B To the interface cable of a car telephone das Gerät beschädigt werden. l’appareil. evitare di causare danni all’apparecchio. beschadigd.
B An Schnittstellenkabel eines Autotelefons B Vers le cordon de liaison d’un téléphone de B Al cavo di interfaccia di un telefono per auto B Naar het interface-snoer van een
Warning voiture autotelefoon
If you have a power aerial without a relay box, Warnung Avvertenza
connecting this unit with the supplied power connecting Wenn Sie eine Motorantenne ohne Relaiskästchen Avertissement Quando si collega l’apparecchio con il cavo di Waarschuwing
lead 3 may damage the aerial. verwenden, kann durch Anschließen dieses Geräts mit Si vous disposez d’une antenne électrique sans boîtier alimentazione in dotazione 3, si potrebbe danneggiare Indien u een elektrische antenne hebt zonder relaiskast,
Notes on the control power and suppy leads dem mitgelieferten Stromversorgungskabel 3 die de relais, le branchement de cet appareil au moyen du l’antenna elettrica se questa non dispone di scatola a relè. kan het aansluiten van deze eenheid met het bijgeleverde
• The power aerial control lead (blue) supplies +12 V DC when Antenne beschädigt werden. cordon d’alimentation fourni 3 risque d’endommager Note sui cavi di controllo e di alimentazione netsnoer 3 de antenne beschadigen.
you turn on the tuner, or when you activate the AF (Alternative Hinweise zu den Steuer- und Stromversorgungsleitungen l’antenne. • Il cavo (blu) di controllo dell’antenna elettrica fornisce Opmerkingen over de bedienings- en voedingskabels
Frequency) or TA (Traffic Announcement) function. • Die Motorantennen-Steuerleitung (blau) liefert +12 V Remarques sur les câbles de commande et d’alimentation alimentazione pari a +12 V CC quando si attiva il • De antennevoedingskabel (blauw) levert +12 V gelijkstroom
• When your car has built-in FM/MW/LW aerial in the rear/side Gleichstrom, wenn Sie den Tuner einschalten oder die • Le câble de commande (bleu) fournit du courant continu de sintonizzatore oppure la funzione TA (notiziario sul traffico) o wanneer u de tuner inschakelt of de AF (Alternative
glass, connect the power aerial control lead (blue) or the AF- (Alternativfrequenzsuche) oder die TA-Funktion +12 V lorsque vous mettez le tuner sous tension ou lorsque AF (frequenza alternativa). Frequency) of TA (Traffic Announcement) functie activeert.
accessory power input lead (red) to the power terminal of the (Verkehrsdurchsagen) aktivieren. vous activez la fonction AF (fréquence alternative) ou TA • Se l’automobile è dotata di antenna FM/MW/LW incorporata • Wanneer uw auto is uitgerust met een FM/MW/LW-antenne
existing aerial booster. For details, consult your dealer. • Wenn das Fahrzeug mit einer in der Heck-/ (informations de circulation). nel vetro posteriore/laterale, collegare il cavo (blu) di in de achterruit/zijruit, moet u de antennevoedingskabel
• A power aerial without a relay box cannot be used with this Seitenfensterscheibe integrierten FM (UKW)/MW/LW- • Lorsque votre voiture est équipée d’une antenne FM/MW controllo dell’antenna elettrica o il cavo (rosso) di ingresso (blauw) of de hulpvoedingskabel (rood) aansluiten op de
unit. Antenne ausgestattet ist, schließen Sie die Motorantennen- (GO)/LW (PO) intégrée dans la vitre arrière/latérale, dell’alimentazione accessoria al terminale di alimentazione voedingsingang van de bestaande antenneversterker.
Memory hold connection Steuerleitung (blau) oder die Zubehörstromversorgungsleitung raccordez le câble de commande d’antenne (bleu) ou del preamplificatore dell’antenna esistente. Per ulteriori Raadpleeg uw dealer voor meer details.
When the yellow power input lead is connected, power will (rot) an den Stromversorgungsanschluss des vorhandenen l’entrée d’alimentation des accessoires (rouge) au bornier informazioni, consultare il proprio fornitore. • Met dit apparaat is het niet mogelijk een automatische antenne
always be supplied to the memory circuit even when the ignition Antennenverstärkers an. Näheres dazu erfahren Sie bei Ihrem de l’amplificateur d’antenne existant. Pour plus de détails, • Non è possibile usare un’antenna elettrica senza scatola a relè zonder relaiskast te gebruiken.
switch is turned off. Händler. consultez votre revendeur. con questo apparecchio.
Instandhouden van het geheugen
• Es kann nur eine Motorantenne mit Relaiskästchen • Une antenne électrique sans boîtier de relais ne peut pas être Collegamento per la conservazione della memoria Zolang de gele stroomdraad is aangesloten, blijft de
Notes on speaker connection angeschlossen werden.
• Before connecting the speakers, turn the unit off. utilisée avec cet appareil. Quando il cavo di ingresso alimentazione giallo è collegato, stroomvoorziening van het geheugen intact, ook wanneer het
• Use speakers with an impedance of 4 to 8 ohms, and with Stromversorgung des Speichers Raccordement pour la conservation de la mémoire viene sempre fornita alimentazione al circuito di memoria anche contact van de auto wordt uitgeschakeld.
adequate power handling capacities to avoid its damage. Wenn die gelbe Stromversorgungsleitung angeschlossen ist, Lorsque le câble de commande d’antenne jaune est connecté, le quando l’interruttore di accensione è spento.
Opmerkingen betreffende het aansluiten van de luidsprekers
• Do not connect the speaker terminals to the car chassis, or wird der Speicher stets (auch bei ausgeschalteter Zündung) mit circuit de la mémoire est alimenté en permanence même si la clé Note sul collegamento dei diffusori • Zorg dat het apparaat is uitgeschakeld, alvorens de
connect the terminals of the right speakers with those of the Strom versorgt. de contact est en position d’arrêt. • Prima di collegare i diffusori spegnere l’apparecchio. luidsprekers aan te sluiten.
left speaker. Hinweise zum Lautsprecheranschluss Remarques sur le raccordement des haut-parleurs • Usare diffusori di impedenza compresa tra 4 e 8 ohm e con • Gebruik luidsprekers met een impedantie van 4 tot 8 Ohm
• Do not connect the earth lead of this unit to the negative (–) • Schalten Sie das Gerät aus, bevor Sie die Lautsprecher • Avant de raccorder les haut-parleurs, mettre l’appareil hors capacità di potenza adeguata, altrimenti i diffusori potrebbero en let op dat die het vermogen van de versterker kunnen
terminal of the speaker. anschließen. tension. venire danneggiati. verwerken. Als dit wordt verzuimd, kunnen de luidsprekers
• Do not attempt to connect the speakers in parallel. • Verwenden Sie Lautsprecher mit einer Impedanz zwischen 4 und • Utiliser des haut-parleurs ayant une impédance de 4 à 8 ohms • Non collegare i terminali del sistema diffusori al telaio dell’auto ernstig beschadigd raken.
• Connect only passive speakers. Connecting active speakers 8 Ohm und ausreichender Belastbarkeit. Ansonsten können die et une capacité adéquate sous peine de les endommager. e non collegare i terminali del diffusore destro a quelli del • Verbind in geen geval de aansluitingen van de luidsprekers
(with built-in amplifiers) to the speaker terminals may damage Lautsprecher beschädigt werden. • Ne pas raccorder les bornes du système de haut-parleurs au diffusore sinistro. met het chassis van de auto en sluit de aansluitingen van de
the unit. • Verbinden Sie die Lautsprecheranschlüsse nicht mit dem châssis de la voiture et ne pas connecter les bornes du haut- • Non collegare il cavo di terra di questo apparecchio al rechter- en linkerluidspreker niet op elkaar aan.
• To avoid a malfunction, do not use the built-in speaker leads Wagenchassis und verbinden Sie auch nicht die Anschlüsse parleur droit à celles du haut-parleur gauche. terminale negativo (–) del diffusore. • Verbind de aarddraad van dit apparaat niet met de negatieve
installed in your car if the unit shares a common negative (–) des rechten mit denen des linken Lautsprechers. • Ne pas raccorder le câble de mise à la masse de cet appareil • Non collegare i diffusori in parallelo. (–) aansluiting van de luidspreker.
lead for the right and left speakers. • Verbinden Sie die Masseleitung dieses Geräts nicht mit dem à la borne négative (–) du haut-parleur. • Assicurarsi di collegare soltanto diffusori passivi, poiché • Probeer nooit de luidsprekers parallel aan te sluiten.
• Do not connect the unit’s speaker leads to each other. negativen (–) Lautsprecheranschluss. • Ne pas tenter de raccorder les haut-parleurs en parallèle. il collegamento di diffusori attivi, dotati di amplificatori • Sluit geen actieve luidsprekers (met ingebouwde versterkers)
Note on connection • Versuchen Sie nicht, Lautsprecher parallel anzuschließen. • Connecter uniquement des haut-parleurs passifs. La incorporati, ai terminali dei diffusori potrebbe danneggiare aan op de luidspreker-aansluiting van dit apparaat. Dit zal
If speaker and amplifier are not connected correctly, “FAILURE” • An die Lautsprecheranschlüsse dieses Geräts dürfen nur connexion de haut-parleurs actifs (avec des amplificateurs l’apparecchio. leiden tot beschadiging van de actieve luidsprekers. Sluit dus
appears in the display. In this case, make sure the speaker and Passivlautsprecher angeschlossen werden. Schließen Sie intégrés) aux bornes des haut-parleurs pourrait endommager • Per evitare problemi di funzionamento, non utilizzare i cavi dei altijd uitsluitend luidsprekers zonder ingebouwde versterker
amplifier are connected correctly. keine Aktivlautsprecher (Lautsprecher mit eingebauten l’appareil. diffusori incorporati installati nell’automobile se l’apparecchio aan.
Verstärkern) an, da das Gerät sonst beschädigt werden • Pour éviter tout dysfonctionnement, n’utilisez pas les câbles condivide un cavo comune negativo (–) per i diffusori destro e • Om defecten te vermijden mag u de bestaande
könnte. des haut-parleurs intégrés installés dans votre voiture si sinistro. luidsprekerbedrading in uw auto niet gebruiken wanneer er een
• Um Fehlfunktionen zu vermeiden, verwenden Sie nicht die l’appareil dispose d’un câble négatif commun (–) pour les haut- • Non collegare fra loro i cavi dei diffusori dell’apparecchio. gemeenschappelijke negatieve (–) draad is voor de rechter- en
im Fahrzeug installierten, integrierten Lautsprecherleitungen, parleurs droit et gauche. Nota sui collegamenti linkerluidsprekers.
wenn am Ende eine gemeinsame negative (–) Leitung für den • Ne raccordez pas entre eux les cordons des haut-parleurs de Se l’amplificatore e il diffusore non sono collegati correttamente, • Verbind de luidsprekerdraden niet met elkaar.
rechten und den linken Lautsprecher verwendet wird. l’appareil. “FAILURE” viene visualizzato nel display. In tal caso, accertarsi Opmerking over aansluiten
• Verbinden Sie nicht die Lautsprecherkabel des Geräts che l’amplificatore e il diffusore siano collegati correttamente. Als de luidspreker en versterker niet correct zijn aangesloten,
miteinander. Remarque sur le raccordement
Si les enceintes et l’amplificateur ne sont pas raccordés wordt "FAILURE" in het display weergegeven. In dit geval moet u
Hinweis zum Anschließen correctement, le message « FAILURE » s’affiche. Dans ce cas, zorgen dat de luidspreker en versterker correct zijn aangesloten.
Wenn Lautsprecher und Verstärker nicht richtig angeschlossen assurez-vous que les enceintes et l’amplificateur sont raccordés
sind, erscheint „FAILURE“ im Display. Vergewissern Sie sich correctement.
in diesem Fall, dass Lautsprecher und Verstärker richtig
angeschlossen sind.
10
CDX-R5515X/R5610/R6550
SECTION 2
DISASSEMBLY
Note : This set can be disassemble according to the following sequence.
SET
2-1. SUB PANEL (LCD) ASSY

(Page 12)
2-2. CD MECHANISM BLOCK

(Page 12)
2-4. CHASSIS (T) SUB ASSY 2-3. MAIN BOARD 2-10. SERVO BOARD
(Page 13) (Page 13) (Page 16)
2-5. ROLLER ARM ASSY

(Page 14)
2-6. CHASSIS (OP) ASSY 2-9. LE MOTOR ASSY (M903)

(Page 14) (Page 16)
2-8. SL MOTOR ASSY (M902) 2-7. OPTICAL PICK-UP

(Page 15) (Page 15)
FRONT PANEL COMPLETE ASSY
2-11. FRONT BACK PANEL (LCD)

(Page 17)
2-12. KEY BOARD

(Page 17)
2-13. DISPLAY SECTION

(Page 18)
2-14. SPRING (M)

(Page 18)
2-15. SPRING (S)

(Page 19)
11
CDX-R5515X/R5610/R6550
Note : Follow the disassembly procedure in the numerical order given.
2-1. SUB PANEL (LCD) ASSY
3 two claws
2 two claws
1 two screws
(+PTT 2.6 x 6)
4 sub panel (LCD) assy
2-2. CD MECHANISM BLOCK
7 bracket (CD)
5 CD mechanism block
6 two screws
(+PTT 2.6 x 4)
2 screw 3
(+PTT 2.6 x 6)
1 screw
(+PTT 2.6 x 6)
4 CN350
12
CDX-R5515X/R5610/R6550
2-3. MAIN BOARD
1 three screws
(+BTT)
2 two screws
(+PTT 2.6 x 8)
3 MAIN board
4 insulating sheet
2-4. CHASSIS (T) SUB ASSY
4 claw
2 two screws
(+P 1.7 x 2.2)
1 two screws
(+P 1.7 x 2.2)
6 chassis (T) sub assy
5 SENSOR board
3 claw
13
CDX-R5515X/R5610/R6550
2-5. ROLLER ARM ASSY
3 washer (1.1-2.5)
5 roller arm assy
4 gear (RA1)
2 spring (RAR)
1 spring (RAL)
2-6. CHASSIS (OP) ASSY
8
qa chassis (OP) assy
0 coil spring (damper)
lever (D)
4 washer
1 CN2 (16P)
6
5 gear (LE1) 9 two coil springs (damper)
slider (R)
3 tension coil spring (KF60)

2 Remove the six solderings.
14
CDX-R5515X/R5610/R6550
2-7. OPTICAL PICK-UP
2 chucking arm sub assy
5 claw
1 tension coil spring (CHKG)
7 optical pick-up
6 main shaft
4 rack (SL)
3 screw
(+B 1.4 x 5)
2-8. SL MOTOR ASSY (M902)
1 screw
(+P 1.4 x 1.8)
2 SL motor assy (M902)
15
CDX-R5515X/R5610/R6550
2-9. LE MOTOR ASSY (M903)
0 gear (LE) assy 8 screw

(+M 1.7 x 2.5)
9 bearing (LEB-N)
qa screw 2 washer
qf two toothed lock screws (+M 1.7 x 2.5)
3 gear (LE1)
(+M 1.4 )
lever (D)
4
bracket (LEM-N)
qs screw qg LE motor assy 5
(+M 1.7 x 2.5) (M903)
qd
6 screw
(+P 1.7 x 2.2)
slider (R)
7 leaf spring (LE)
1 Remove the soldering.
2-10. SERVO BOARD
1 Remove the eight solderings. 6 SERVO board
2 Remove the three solderings.
4 toothed lock screw

(M 1.7)
5 claw
3 CN2(16P)
16
CDX-R5515X/R5610/R6550
2-11. FRONT BACK PANEL (LCD)
2 two screws
(+P 2 x 8)
three claws
two claws
1 two screws
(+P 2 x 8)
two claws
three claws 3 front back panel (LCD)
2-12. KEY BOARD
2 CN903 (6P)
4 KEY board
3 CN902 (12P)
17
CDX-R5515X/R5610/R6550
2-13. DISPLAY SECTION
Note for assembly 4 display section

After installing to the front panel assy,
make sure the spring is not off
from the dowel.
2 two screws
(+P 2 x 8)
Note for assembly

After installing to the front panel assy,
make sure the spring is not off from the dowel.
front panel assy 1 Raise the preset assy up in the arrowed direction.
2-14. SPRING (M)
2 spring (M)
3 bracket (display)
1 spring (M)
18
CDX-R5515X/R5610/R6550
2-15. SPRING (S)
5 spring (S)
display (SV) assy

Note for assembly
3 Take off the spring from

display (SV) assy the dowel on preset assy side.
4 spring (S)
dowel
spring (S)
preset assy
1 Raise the preset assy

up in the arrowed direction.
Make sure the spring
is not off from the dowel. 2 Take off the spring from
display (SV) assy
the dowel on preset assy side.
dowel
spring (S)
Put preset assy back

in the arrowed direction.
preset assy
Make sure the spring is not off from the dowel.
19
CDX-R5515X/R5610/R6550
MEMO
20
CDX-R5515X/R5610/R6550
SECTION 3
DIAGRAMS
3-1. BLOCK DIAGRAM — CD SECTION —
• R-ch is omitted due to same as L-ch.

• Signal Path
DETECTOR : CD PLAY
PD2
PD2 RFO 87 MAIN
96 FPI2 RFEQO 79 77 RFI 85 AGCI LO 30 CD-L A SECTION
PD1 78 RFRPI 86 RFDCI
PD1 RO 27 R-CH (Page 22)
94 FNI2
97 FPI1 MAIN
ATT B SECTION
95 FNI1 A ATT 60 (Page 22)
I-V AMP
RF AMP,DIGITAL SERVO,
DIGITAL SIGNAL PROCESSOR UNISI 56 UNI SI
IC2 RXD 25
E UNISO 57 UNI SO
E
99 TNI RFRP 3 1 RFZI TXD 26
F UNICKI 58 UNI CLK DISPLAY
F
98 TPI TEI 6 7 TEZI
C SECTION
BUS ON 50 BUS ON
MUTE 56 37 DEC XMUTE
BU IN 51 B/U CHECK (Page 23)
REQ 53 30 DEC INT
LINK OFF 59 LINK OFF
LASER DIODE STBY 43 27 DEC SSTBY
ZDET 18 15 CD ZDET RSTX 75 SYS RST
AUTOMATIC /RST 42 14 CD XRST
LD+ POWER 41 13 CD XCCE
91 LDO MDI 92 /CCE SYSTEM CONTROL
CONTROL
BUCK 40 12 CD BUCK IC501 (1/3)
PD LD Q1
BUS3 39 11 CD BUS3
BUS2 38 10 CD BUS2
BUS1 37 8 CD BUS1 EJECT OK 61 89 EJECT OK SW
MON OUT MECON 63 99 CDM ON
BUS0 36 7 CD BUS0
14 52 CD SBSY CDON 64 98 CD ON
SBSY
ZMUTE 66 93 Z MUTE
CD
SYSTEM CONTROL
OPTICAL IC3 MECON CHK 67 MECHA+6V
PICK-UP BLOCK
(KSS1000E) FOCUS/TRACKING COIL DRIVE,
SLED/SPINDLE/LOADING
MOTOR DRIVE
IC1 CDON CHK 68 SERVO+3.3V
XI 23 81 X1 +1.5V REG
2-AXIS DEVICE FCS+ X2 X1
16 VO4– OPIN4– 26 9 F0O IC6
16.9344MHz 12MHz
FCS– +1.5V ON/OFF
15 VO4+ OPOUT4 25 XO 24 80 X0
DEC+1.5V SWITCH 5 VOUT VDD 1 BU+3.3V
(FOCUS) Q2,3 CE 3
(TRACKING)
TRK+ SW1 46 MEC_DSW
18 VO3– OPIN3– 23 10 TRO
(DOWN) +1.5V
TRK–
17 VO3+ OPOUT3 22 46 IO0(/HSO)
SW2 53 MEC_SELFSW
(SELF)
14 VO1+ OPOUT1 4 12 FMO DECON 1
M902 M
(SLED) 13 VO1– SW3 45 MEC_INSW
MUTE 21 47 IO1(/UHSO) (DISC IN)
M901 12 VO2+ OPOUT2 7 13 DMO SW4 42 MEC_LIMIT

(SPINDLE) M (LIMIT)
11 VO2–
M903 10 VOL+
(LOADING) M FWD 1 43 MEC LOAD
9 VOL–
REV 28 44 MEC EJECT
CDX-R5515X/R5610/R6550
21 21
CDX-R5515X/R5610/R6550
3-2. BLOCK DIAGRAM — MAIN SECTION —
J451 (1/3)
L FRONT
ELECTRONIC VOLUME
IC401 AUDIO OUT
R-CH R
CD
SECTION A CD-L 9 SE1L J451 (2/3)
R-CH 10 SE1R OUT LR2 16 L REAR
(Page 21)
OUT RR2 28 R-CH AUDIO OUT
R-CH R
J451 (3/3)
L 11 DIFFL POWER AMP,
BUS AUDIO
POWER SUPPLY
TU1 IN/AUX MUTE
R 13 DIFFR IC300
(TUNER UNIT) Q430
CN300
J1 1 ANT L-CH 4 7 SE2L 1
(ANTENNA) OUT LF 20 12 IN FL OUT FL+ 5 FL+
R-CH 3 8 SE2R 9
OUT FL- 3 FL-
OUT LR1 19 11 IN RL
OUT RF 17 R-CH (FRONT) 2
MUTE MUTE OUT RL+ 9 RL+
OUT RR1 18 R-CH (REAR) 10
Q440 Q470 OUT RL- 7 RL-
VCC 10 AUDIO+8.3V MUTE 21
26 SA OUT 4
VDD5V 11 TU+5V SCL FR+
SCL 22 12
E2P VDD 15 BU+3.3V 25 SA IN SDA FR-
SDA 23 D491 R-CH 3
MUTE DRIVE RR+
Q491,492 BATT 11
RR-
SCL
TU-SCL 13
SDA
TU-SDA 14 5
AMP-REM 29 AMP-REM
SYSTEM CONTROL 6
IC501 (2/3) ANT-REM 27 ANT-REM
F901
45 SA CKO SCL SDA 16
I2C CKO 33 2 SDA BATT
44 SA IN SDA SCL
I2C SIO 34 D493 4 SCL
S-METER 6 39 VSM
VOL ATT 9
TUN MUTE 7 12 TU ATT
AUDIO+B 30 AUDIO+8.3V
ATT 86 B.UP+B 37
E2P SCL 16 25 EEP CKO BU+5V
BEEP 5 16 BEEP SERVO3.3V 31
E2P SDA 17 24 EEP SIO SERVO+3.3V
AMP STB 26 22 STB MECHA6V 33 MECHA+6V
MUTE CONDITION 8 53 TU ATT IN DIAG 8 25 DIAG PANEL+B 34 PANEL+B
QUALITY 5 38 QUALITY 6 VP2
NS MASK 20 VP1
CONTROL 13 NS MASK BATT 35 VP
Q1
RDS DECODER TEL MUTE 13

IC50 TEL ATT 74 Q701 TEL-MUTE
SCL
9 XTI SCL 11 ACC CHECK 7
X50 SDA ACC IN 72 Q702 ACC
SDA 12
8.664MHz
10 XTO 15
INTN 15 56 DAVN TEST IN 73 TEST
RDS 9 16 MPX
ILL 14
VDDA VDDD 30 RDS ON ILLUMI 75 NC
Q703
1 7
RDS POWER • R-CH is omitted due to same as L-CH. +5V REG

TU+5V AUDIO+8.3V
CONTROL BU+3.3V • Signal Path Q3
Q50
: CD PLAY
R6550 ONLY : FM IC502
: MW/LW +3.3V
CD BU+3.3V 3 2 BU+5V
REG
SECTION B ATT
(Page 21)
CDX-R5515X/R5610/R6550
22 22
CDX-R5515X/R5610/R6550
3-3. BLOCK DIAGRAM — DISPLAY SECTION —
SYSTEM CONTROL LCD DRIVER

IC501 (3/3) IC901
NC1 2
KEY MATRIX 41 KEYIN0 NC2 29
LSW903-913,918-921
S902,914-918 LCD SO 28 78 DI
40 KEYIN1 S1 3-28, LCD911
LCD CKO 29 CLK
77 CL | 30-64,
D501 (1/2) LCD CE 27 76 CE S48 69 LIQUID
CRYSTAL
COM1 65 DISPLAY
KEY ACK ON | | PANEL
Q501 52 KEY ACK
COM4 68
76 XKEY ON 1
PANEL+B
D501 (2/2)
LED931,932
J370
43 RC IN0
(REMOTE IN)
71 RC IN1
( LCDLIGHT
BACK
)
LED902,914-918
BUS INTERFACE LSW903-913,918-921
BATT Q605 IC601
BATT
3 BATT B/U CHECK 10 54 BU IN
CHECK
CNJ400 Q925
7 LED
( BUS CONTROL
IN ) 1 4 4 CLK OUT CLK IN 11 60 UNI SCK CONTROL
2 5 6 DATA I/O DATA OUT 8 58 UNI SI
3 6 DATA IN 9 59 UNI SO
Q600,601 BU+3.3V
8
BUS ON
1 BUS ON OUT BUS ON IN 12 87 BUS ON
CONTROL 10k
AREA SEL0 27 r
2 RST OUT RST IN 13
9k
S501
LINK OFF
B/U CHECK
( FREQUENCY
SELECT )
UNI CLK R5610 ONLY
CD
SECTION C UNI SI
UNI SO
(Page 21)
BUS ON
SYS RST SYNCHRO SW 70 PANEL+B
LED961
KEY BOARD LSW901
7 NOSE SW
S961
(NOSE DET)
D400
88 SYS RST
RESET
IR RECEIVER
IC602
IC972
BU+3.3V 2 VDD VOUT 1 77 RESET
SIRCS 64 2 OUT IR
S103
RESET
OSC OUT 83
79 XIN X500
X501 18.432MHz
32.678kHz OSC IN 82
80 XOUT
CDX-R5515X/R5610/R6550
23 23
CDX-R5515X/R5610/R6550
3-4. CIRCUIT BOARDS LOCATION • NOTE FOR PRINTED WIRING BOARDS AND SCHEMATIC DIAGRAMS
THIS NOTE IS COMMON FOR PRINTED WIRING

BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this, the necessary note is printed
SERVO board in each block.)
SENSOR board
For schematic diagrams. For printed wiring boards.
Note: Note:
• All capacitors are in µF unless otherwise noted. (p: pF) • X : parts extracted from the component side.
50 WV or less are not indicated except for electrolytics • Y : parts extracted from the conductor side.
and tantalums. • a : Through hole.
KEY board • All resistors are in Ω and 1/4 W or less unless otherwise • : Pattern from the side which enables seeing.
specified. (The other layers' patterns are not indicated.)
• f : internal component.
• C : panel designation. Caution:
DISPLAY board Pattern face side: Parts on the pattern face side seen from the
Note: Note: (Side B) pattern face are indicated.
The components identi- Les composants identifiés par Parts face side: Parts on the parts face side seen from the
fied by mark 0 or dotted une marque 0 sont critiques (Side A) parts face are indicated.
tuner unit line with mark 0 are criti- pour la sécurité.
(TU1) cal for safety. Ne les remplacer que par une
Replace only with part piéce portant le numéro C
PRESET board MAIN board number specified. spécifié.
Q These are omitted
• A : B+ Line.
• B : B– Line. B E
• H : adjustment for repair.
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
• CD mechanism section (1/2), (2/2)
• WAVEFORMS no mark : CD PLAY BE C
• Main (1/2), (2/2), Key and Display sections
These are omitted
no mark : FM
— SERVO BOARD — ( ) : AM/MW/LW
(CD PLAY) < > : CD PLAY
∗ : Impossible to measure
ECB
• Voltages are taken with a VOM (Input impedance 10 MΩ).
1 IC2 4 (FEI) 4 IC2 uj (RFI) 7 IC3 ia (X1) Voltage variations may be noted due to normal produc- These are omitted
tion tolerances.
• Waveforms are taken with a oscilloscope.
Approx. Voltage variations may be noted due to normal produc-
0V 1Vp-p 1.1 Vp-p tion tolerances.
• Circled numbers refer to waveforms.
Approx. 100 mVp-p • Signal path.
12 MHz J : CD PLAY
F : FM
50 mV/DIV, 5 msec/DIV 0.5 V/DIV, 0.5 µsec/DIV 0.5 V/DIV, 0.2 µsec/DIV f : AM/MW/LW
2 IC2 6 (TEI) 5 IC2 of (FNI2), og (FNI1)

— MAIN BOARD —
0V
1.5 Vp-p 1 IC50 0 (XTO) 3 IC501 id (OSCOUT)
Approx. 400 mVp-p

1.1 Vp-p 1.1 Vp-p
200 mV/DIV, 5 msec/DIV 0.5 V/DIV, 0.5 µsec/DIV
8.664 MHz 18.432 MHz
3 IC2 wd (XI) 6 IC2 oh (FPI2), oj (FPI1)
0.5 V/DIV, 0.2 µsec/DIV 0.5 V/DIV, 0.1 µsec/DIV
0.6 Vp-p 1.5 Vp-p 2 IC501 i; (XOUT)
16.9344 MHz
0.7 Vp-p
0.2 V/DIV, 0.2 µsec/DIV 0.5 V/DIV, 0.5 µsec/DIV
32.768 kHz
0.2 V/DIV, 20 µsec/DIV
CDX-R5515X/R5610/R6550
24 24
CDX-R5515X/R5610/R6550
3-5. PRINTED WIRING BOARDS — CD MECHANISM SECTION — • Refer to page 24 for Circuit Boards Location. : Uses unleaded solder.
1 2 3 4 5 6 7 8 9 10 11 12 13 14
A TP29
TP27
TP26
TP25
TP93
C17
TP22
FMB3
C18
C20
C9 C24
C23
FMA6
TP15
C28
Q1
R132 TP14 C16 C13 C21
C31
TP33
TP30
TP34
C22
C33
C27
R13 R6
R7
R19
C7
TP21
C29
C19
B C38
TP37 TP41 R22
C35
C34
R23
R21
TP18
TP36
TP17
C41
C39 TP42 R24

C32
TP38
TP35
C40
C36
IC2
TP40
R26
R25
TP46
TP39 R41
C42
TP68
TP47
R16
R17
Q3
R84 R71
C102
C101
X2
C45
R44
C47
R45
C R86 C51 R40
R46
C48
R123
R68 C67
C57
C62
R51 C49 C52
R59
FB4 TP64
R72
R127
R126
Q2
R66
R52
R48 C58 R128
R58
C72
C53
C59 R49
FMB4
R122 R60
C10
R50
FMA4 R125 R78

C80
R64 TP65
IC6
R4
R56
R54
C106
R61
TP13 R63
R118
R119
R62
TP16
D TP12 TP67
R5
R117
C60
C4 TP66
R1
TP95 TP43 R121 SW3
TP20 TP101
R80
R90
TP62
TP24
C5
TP88
R91
TP44
CN
IC3
C105
R83
TP63
R67
TP89 TP74
R28
R82
C103
TP90
R120
X1
TP77
E TP91
R81
SW2
FB3
FMA5
C37
TP78
TP92 R116
R70
TP76 TP75
FM
R42 C43 TP82
R112
B5
R77
C61
TP48 TP3
C65
R47 TP79
R69
R65
R57
C64
TP49 TP6 TP80 R74
CN2
R131
TP51 TP81
R43
TP53 R55 TP4

R73 R100 TP7 R53
R101
FB2
TP98
F R113 TP2 TP97 TP83
TP5
TP84
TP1
TP31
TP99 TP85 X1
TP32
R9 TP9
R10
TP86
R11
TP23
R8 R12
TP8
G FMA3
TP11
IC1
TP87
R3
TP10
R2
SW1
C6
(DOWN)
H
11 11
1-864-900- 11 1-864-900- 11
• Semiconductor
A Location
MAIN BOARD CN350 Ref. No. Location
(Page 28) IC1 G-2
IC2 B-11
IC3 E-2
IC6 D-1
Q1 B-4
Q2 C-1
Q3 C-1
CDX-R5515X/R5610/R6550
25 25
CDX-R5515X/R5610/R6550
• Refer to page 24 for Waveforms.

3-6. SCHEMATIC DIAGRAM — CD MECHANISM SECTION (1/2) — • Refer to page 36 for IC Block Diagrams.
IC B/D
C32 C35 IC6
C29 R21 Q2 R86
R19
R84
Q3
R22
R24
C80
R44
TP46
TP47
C28 C36 C67 C72
C102
C31
R23
C24 C47
C52
R52 C53
C13 C21 TP25

TP26
C18
TP27 R72
R13 R71
C22
C19 C51
C20
TP93 C62
C23 R59
C17 R60
TP29 R125 R61
IC2 R126 R62
C16 R127 R63
R128 R64
CN1
C49 C57
C48
R113
R49
R4 C60
C4
TP12 C58 TP101
TP13 C10
TP14 TP30 R131
C59
TP15
R51
TP16 R1
TP17
IC B/D
TP18
C101 R123
C5
TP41
TP42
TP33
TP34
TP35
TP36
TP20 C27
C45
C33
R5
FB4
C42
R25
R26
R45 R46
R40
R41
X2
FB3
C34
C38
C39
C40
C41
FB2 C61
R112
C7
TP37
TP38
TP39
TP40
Q1
TP21 TP22
R132 C9 R6 R7
(Page 27)
CDX-R5515X/R5610/R6550
26 26
CDX-R5515X/R5610/R6550
• Refer to page 24 for Waveform.

• Refer to page 36 for IC Block Diagram.
3-7. SCHEMATIC DIAGRAM — CD MECHANISM SECTION (2/2) — • Refer to page 38 for IC Pin Description.
(Page 26)
(Page 30)
R116
R73 R74
CN2
TP74 TP88
TP75 TP89
R42 R43 C43 R47 C65
TP76 TP90
TP77 TP91
TP48
TP49
TP51
TP53
TP78 TP92
R57
R65
R67
R69
R70
TP62
C64
R53
TP79
R55
TP80
TP81
TP82
TP83 TP97
TP98 R77
TP84 X1
TP85 TP99
R100 TP86
TP87
R101
C37
R81
R28 R82
R120 C103
R83
TP1 IC B/D IC3

SW4
R80
TP63
TP2
IC1 TP44
SW1
R121
R10 R16
R3 C105
TP3 R8
SW3 R11
R2 TP64
TP43
TP65 R78
TP4 R9 R17
SW2 TP66
R91
TP5
C6 R12
TP10
TP67 R90
M903
TP11 TP23
TP24
R118
R119
R48
R50
R54
R56
R58
R66
R68
TP7 TP31
TP32 C106
M901
TP6
R122
R117
TP9
M902
TP8
CDX-R5515X/R5610/R6550
27 27
CDX-R5515X/R5610/R6550
3-8. PRINTED WIRING BOARD — MAIN SECTION — • Refer to page 24 for Circuit Boards Location. : Uses unleaded solder.
1 2 3 4 5 6 7 8 9 10 11 12 13 14
J451
AUDIO OUT
BUS IN REAR FRONT
A CNJ400 J370
(REMOTE IN)
EXCEPT R6550
(BUS CONTROL IN)
J1 JC302 CNJ400
(ANTENNA) J451
JC300
JC301
CN300
C452
C414 C323
C442 C422 C324
L301
JW134
C432
J1 C309 C307 C305
C329
17 F901 18 19
R452 JW133 C301
C413 R432 R442 R422 C304
3 2 1
JC998
B 8 7
L302
JW136
IC300 9 16 6 5 4
1 8
Q450
Q420
Q430 C462 JW123 JW122
JW49
JC360
JW128
JW129
JW127
JW126
R423 JW121
JW132
JW47
C320
JW131
JW124
JW130
JW50
Q440
C423
JW51
JW125
JC490 R463
C701
C472
Q460
C303
C901
R701
C443
C JW52
JW45
R462
JW46
C902
D306
R443
D607
JC491 Q470 D701
D305
D308
D307
D311
R473
D310
R441
R421
R451 L300
D312
D309
R358
R357
C308
R472
D304 C704
JC1
D301
D703
D302
C310
C451
C14 C441 JC430 R703

Q701 D303 R6550
L303
R356
R359
TU1
C471
R471
JW48
TUNER UNIT R461 C313 R709
R431
C306 C315
JC420
C367 R702
C312
D R355
C461
C314 C316 R704 JW120
C421
TH400
C365
C431
JW119
C362
JW56
JW60
JW53
JW118
JW61
JW62
C361
JW135 JW43
JW44
R2 JW55 JW117
JW57
JW58
CN350
R3 C486 JW116 C600
JW59
JW42 Q492
JW63
C491
R430 15 14 JW54
R4
C364
C1 R420 R491
E R5
R1
JW40 Q491
D491
L401 FB402
FB401
R8
C317
IC502
C501
R460 R470 JW114
C417
JW113
C405
Q1
C502
FB408
R440
IC401
R9
C403 D606
R483
C483
C3 C482 JW112
R603
R6550 JW64 C412 D605
JC3 C2 C419 FB407 L400
C481 R402 D704
R450
R482
D2 R484 D602
JW65 FB406
C363
C9 Q605
R604
C7 FB403
JW72
C418
JW71
28 1 JW66 JW111
R12 C480 FB405
R401
R480
R710
R611
JW1 R10
F JW39 C415
R481
C5 JW67 R5515X,R5610
R301
C318
R5610 D603
R13 FB404 JW109
C484 JW38 S501 R302
C319
C8
R6 FREQUENCY R6550 D604

SELECT R351 JW108
S501
C402
L4 JW37 R508
JW70
JC350
R7 Q3
JW75
9K R506 D493 JW107
JW69
R507
• Semiconductor Location
C401
JW68
JW36 Q600
JW2 R5610,R6550 (Page 25)
L1
JW106
C485
R511
JW35 Ref. No. Location Ref. No. Location
JW77
R501 Q601
JW3 R400 R502
JW73
10K
JW74
JW34 D2 F-2 D704 F-10
JW32
JW33
R14 R512 R553
R705
C58 R505 FMB3 R537 D705
G C50
R55
IC50 JC505
R5515X
R5610,R6550
R711 R608 D101 I-3 D705 G-9
JW79
JW76
C51
D102 I-3
JW80
JC504
JW78
R6550 R504 JW103
R554
C52 JC506 C703 JW105

R510
L2 JC507 R509 L500

C54 R712 R706 D301 D-8 IC50 G-2
R58
C53 R708
JW27
L3 R5515X,R5610 C505 D400 JW104

JW22
D302 D-8 IC300 B-6
JW89
R551
JW31
JW23
JW24
JW30
C506
JW25
JW26
R6550 C55 R544 Q703 R707

R545
JW21
R54 R11 D702 R610 D303 D-9 IC401 E-4
C504
C503
C57
X50
R535 Q702
R53 R52 D304 C-9 IC501 H-6
JW88
IC501
R542
JW87
C60 R514
JW86
JC503 R5515X C702 D305 C-6 IC502 E-6
JW85
R57 C56 JC515
JW12
JW82
JW84
R536
R5610,R6550 D306 C-6 IC601 H-10
JW83
JW102
JW28
JW10
JW11
JW9
X500
R515 R606
H R517 R518
JW81
JW4
JW29
C61 Q50 R516 C516 JW101 D307 C-6 IC602 I-9

R549 R607 D308 C-6
JC514
R534
IC601
C62 C507
X501
JC600 D309 C-7 Q1 E-2
JW94
C515 D511 JC601

JC510 R531 R532
C508 D310 C-7 Q3 F-2
R548
C509 R5515X,R5610 R601

JC513
R520 C510 R527 R533

D311 C-6 Q50 H-2
C513
JC501
C511 R529 R602

JC509 D502 C519
R540
R102 C512 R546

R530
JW95
C601 D312 C-7 Q420 B-4
JW13
JW14
R519 R539 R371 R521 R538 D400 G-8 Q430 B-3

JW96
JW8 R547
R541
JC512 R543
JW15
R370 D491 E-6 Q440 C-3

JW16
JW17
IC602
JC502
R525
I R528
C514
JW19
R103
JW18
D101
JW20
D102 R526 R550 D493 G-7 Q450 B-4

JW97 R522
JW93
D501 J-5 Q460 C-4

JW92
JW7
JW91
JW99
JW90
R104
FMB4
JW5
R105 JC511 D502 I-7 Q470 C-4

JW6
R524
R523
JC508 Q501 S103

D511 H-8 Q491 E-5
D501
1-864-695-
D602 F-10 Q492 E-6
D603 F-10 Q501 I-7
CN101 D604 F-11 Q600 G-11
D605 E-10 Q601 G-11
J S103
RESET D606 E-10 Q605 F-11
D607 C-10 Q701 D-8
D701 C-8 Q702 H-9
KEY BOARD
CN901 D702 G-10 Q703 G-9
(Page 31) D703 C-8
CDX-R5515X/R5610/R6550
28 28
CDX-R5515X/R5610/R6550
• Refer to page 24 for Waveform.

3-9. SCHEMATIC DIAGRAM — MAIN SECTION (1/2) — • Refer to page 36 for IC Block Diagram.
C303
J451
JC302
C308
C323 C324 C306
JC300 JC301
C301 C304 C309
C305 C307 C443 R443
C442 C422 C452 C432 C413 C414
IC B/D
C423 R423
C317
IC300 Q440 Q420 Q450 Q430 J1

JC360 C14
C318 C319
JC490 JC491 JC1
TU1
JC998
R301 R302
R442 R422 R452 R432
CN300
R441 R421 R451 JC430
C472 C462 R431
C441 C451
JC420 Q1
R357
R359
R358
C431
R473
R463
C421 R3
R2 R1 C1
R355 R356
D301
D302
C365 C367
C320
R4
C316
C315
C314
C313
C310
C312
R701 R5
IC B/D
R710
R705 R8
D312
D311
D310
D309
D308
D307
D306
D305
D303
D304
R709 C486 R9
F901
D491 Q491 R430 C2
L300 R491 C3
R420
C701 C704 R460 L4 Q3
R462 R461 R470
C461
Q460 R440 C5
C902
C901
C491 C484 R10 C7 C9

Q492 C362
D704
D701
D702
D607
D703
C485 C361 D2 JC3

R472 C482
Q470
C471
R471 R12
R400 JC513 R483 C483
R481 L1 R13
JC514 R484 C364
C8
R6
R450
R482
C481 C363 R7
C480
IC401 R480
R702
R703
D705 R711 R707 Q702
Q703 Q701
IC B/D
C703 R712 R704 R706 C702
R708 IC50
C50 C58
R55
R603
R604
R608 D602 C51
C52 R14
Q605
TH400 Q600 D603
C53
L2
R53 L3
Q601 R54 C57
CNJ400 R52
C601 R602 R601 IC502
R610 C54 C55 R11 X50 C56
C60 C61 C62
R611
R607 R606 Q50
R542
R58
C600 R57
D604 C502 C501
C329 D606 D605

JC601
D511
IC601
IC B/D
(Page 30)
CDX-R5515X/R5610/R6550
29 29
CDX-R5515X/R5610/R6550
• Refer to page 24 for Waveforms.

3-10. SCHEMATIC DIAGRAM — MAIN SECTION (2/2) — • Refer to page 40 for IC Pin Description.
(Page 29)
L303
J370 L302
L301
D501
JC508
R550
(Page 27) R529 R528 R538
JC515
D493
Q501
JC510
D502
R541
R527
R534
R533
R532
R531
R546
R530
R525
C515 X501
CN350
R547
C516 C505 JC509
R370
C506 R526 JC512
C412 C403
JC511
R524
FB408 C417 FB401 X500
R536
FB407 FB402 L401
L400 C405 R402 R535 R523 R522
C419 L500 JC502
FB406
FB405 C415 FB403 R551 R521 R371
R401 C418 R537
JC600 C514
R351 FB404 C513
C512
C510 R539
D400
R553
IC501
C511 R540
C401 C402
C509
R520
C507 R519
JC501
JC350 R548 R549
C508
JC505
S501
JC506
JC504 C508
R514
R515
R516
IC602 C519 R554
C504 C503 R518 JC503
JC507
R511
R544
R509
R510
R543 R507
R517
R508
R501 R502
S103
R506 R504 R505

D101
R512 R545
CN101
R103
R105
R104
(Page 32)
R102
D102
CDX-R5515X/R5610/R6550
30 30
CDX-R5515X/R5610/R6550
3-11. PRINTED WIRING BOARD — KEY SECTION — • Refer to page 24 for Circuit Boards Location. : Uses unleaded solder.
1 2 3 4 5 6 7 8 9 10 11 12 13 14
A LED914 LED902
S914,LED914 S902,LED902
S915
ATT OFF
S917
S917,LED917
S915,LED915
S914 S902
VOL+
(Page 35) (Page 33)
R948
PRESET BOARD DISPLAY BOARD
B LED915
CN905 CN904
LED917
R943
R5515X R5515X
R944
R5610,R6550
D C R949
S961
R5515X (NOSE DET)
SEEK
R902
JP941
CN903 S961
C 12 1
R945
CN902 FMB4
S918,LED918
LED916
R946 LED918
S918
R901
R947
IC972
FMB3
D S916
R972 IC972
S916,LED916 1-864-696- 11
VOL– (Page 28)
MAIN BOARD
CN101
B
E
C973 R952
R975
CN901
R976 R951
R5610,R6550
F JP942
D981
R950
R914
R915 R5515X
R990
D906 D902
R974
R973
D963
D903
D962
G
R913
R916
• Semiconductor
Location
H Ref. No. Location
D902 F-11
D903 G-12 1-864-696- 11
D906 F-9
D962 G-13
D963 F-12
D981 F-7
IC972 D-14
LED902 A-14
LED914 A-1
LED915 B-1
LED916 C-1
LED917 B-13
LED918 C-14
CDX-R5515X/R5610/R6550
31 31
CDX-R5515X/R5610/R6550
3-12. SCHEMATIC DIAGRAM — KEY SECTION —
D902
LED902 LED914 CN901

R973
CN902
R974 R948 R943
LED917 LED915
R976 JP942 R949 R944 (Page 30)
D981
R972
(Page 34)
D906
IC972
R950 JP941 R945

R975
C973
LED918
LED916
R951 R946
CN903 D962 D963 S961
R952 R947
D903 R990
(Page 35)
R916 R915 R914 R913 R902 R901
S918 S917 S916 S915 S914 S902
CDX-R5515X/R5610/R6550
32 32
CDX-R5515X/R5610/R6550
3-13. PRINTED WIRING BOARD — DISPLAY SECTION — • Refer to page 24 for Circuit Boards Location. : Uses unleaded solder.
1 2 3 4 5 6 7 8 9 10 11 12 13 14
LED931
A (LCD BACK LIGHT)
LSW901
LSW901
1 36
R960
LSW921 LSW918 LSW918
LSW921 R953
R917
DSO
B DSPL
R920
LED932
R954
R955
LED931
R961
R962
LCD911
LIQUID CRYSTAL DISPLAY PANEL
R919
R918
LSW919
C EQ3
LSW920
72 37
SEL
1-864-697- 11
LED932
(LCD BACK LIGHT)
D
(Page 31)
KEY BOARD
CN902
C
E
LMB3
F R925 R924
C981
R983
C982
R926
C983
IC901 LMB6
C984
R969
D984
R965
R987
C985
R966
CN904
R964
R980
R981
R982
Q925
G 12 1
LED961
LMB5
LMB4
LED961 1-864-697- 11
(CD SLOT)
H
• Semiconductor
Location
Ref. No. Location
D984 F-5
IC901 F-7
LED931 B-12
LED932 B-3
LED961 G-7
Q925 G-4
CDX-R5515X/R5610/R6550
33 33
CDX-R5515X/R5610/R6550
3-14. SCHEMATIC DIAGRAM — DISPLAY SECTION —
R960 R953 LED931

LED961
CN904
R964 R961 LSW921(2/2) R924
LSW918(2/2)
R965 R954 R925
R966 R962 R955 R926

(Page 32)
R983 LSW919(2/2) LED932
IC901
C982 C981 LSW901(2/2) LSW920(2/2)
C983
C984
C985
R969
Q925
R981
R982
D984
R987
R980
R920 R919 R918 R917
LSW921(1/2) LSW920(1/2) LSW919(1/2) LSW918(1/2) LSW901(1/2)
LCD911
CDX-R5515X/R5610/R6550
34 34
CDX-R5515X/R5610/R6550
3-15. PRINTED WIRING BOARD — PRESET SECTION — • Refer to page 24 for Circuit Boards Location. : Uses unleaded solder.
1 2 3 4 5 6 7 8 9 10 11 12 13 14
A
LSW903 LSW904 LSW905 LSW906 LSW907 LSW908 LSW909 LSW910 LSW911 LSW912 LSW913
1-864-699- 11
LSW903 LSW904 LSW905 LSW906 LSW907 LSW908 LSW909 LSW910 LSW911 LSW912 LSW913
B SOURCE MODE 1/– GP/DISC 2/+ 3/REP 4/SHUF 5/BBE MP 6 AF/TA SENS/BTM PTY/LIST
C R931
CN905
R903 R905 R908 R911 R942 R930
R909
R906 R907 R910
R938
R904
CP901
R933
R912
R932 R934 R935 R936 R937 R939 R940 R941 11
1-864-699-
D D
KEY BOARD
CN903
(Page 31)
3-16. SCHEMATIC DIAGRAM — PRESET SECTION —
R931-940
CN905
R933 R937 R941

CP901
LSW903(2/2) LSW907(2/2) LSW911(2/2) LSW905(2/2) LSW909(2/2) LSW913(2/2)
(Page 32)
R931 R935 R939
LSW904(2/2) LSW908(2/2) LSW912(2/2) LSW906(2/2) LSW910(2/2) R942
R932 R936 R940 R934 R938 R930
R903 R904 R905 R906 R907 R908 R909 R910 R911 R912
LSW903(1/2)
LSW905(1/2)
LSW904(1/2)
LSW906(1/2)
LSW907(1/2)
LSW908(1/2)
LSW909(1/2)
LSW910(1/2)
LSW911(1/2)
LSW912(1/2)
LSW913(1/2)
CDX-R5515X/R5610/R6550
35 35
CDX-R5515X/R5610/R6550
• IC BLOCK DIAGRAMS
IC2 TC94A60MFG-301 (SERVO Board (1/2)) IC1 BA5968FP-E2 (SERVO Board (2/2)) IC300 TDA8588AJ/N2/R1 (MAIN Board (1/2))
VCOREF
PVDD3
LRCKO
VDD15
PVSS3
PVREF
VSS15
TESTC
AWRC
LRCKI
TMAX
DOUT
VDDP
BCKO
AOUT
VCOF
LPFO
LPFN
BCKI
PIO3
PIO2
PIO1
PIO0
PDO
FWD 1 28 REV TAB 1
AIN
75 74 73 72 71 70 69 68 67 66 65 64 63 62 61 60 59 58 57 56 55 54 53 52 51 FWD REV 2 SDA
LDCTL 2 27 OPIN4+
OUT FL- 3 I2C BUS
4 SCL
SLCO 76 VCO PLL AWRC AUDIO DIGITAL 50 VCOI NC 3 OUTR OUTF 26 OPIN4– FL
TMAX OUT OUT 49 VSSP
OPOUT1 4 OUT FL+ 5
RFI 77 EFM SLICE 25 OPOUT4
48 TESTD 6 VP2
RFRPI 78 RFRP NC 5 24 OPIN3+
OUT RL- 7
REFQO 79 RFEQ 47 IO1 NC 6
RL 8 PGND3
46 IO0 23 OPIN3– OUT RL+ 9
RESIN 80 OPOUT2 7
VRO 22 OPOUT3 10 SVR
45 FGIN INRL 11
MUTE
VRO 81
SYNC SIGNAL PROTECTION 44 VDDT 12 INFL
VMDIR 82 EFM DEMODULATION SGND 13
PROTECTION
TESTR 83 43 STBY DIAGNOSTIC 14 INFR
MUTE
POWVCC 8 VCC MUTE 21 MUTE
INVSEL 84 42 /RST INRR 15
CORRRECTION
VOL– 9 20 VOL+
CIRCUIT
AGCI 85 AGC 19 GND 16 AC GND
16K VOL+ 10 VP
RAM 41 /CCE OUT RR+ 17
RFDCI 86 RFDC
CLV SERVO CAV SERVO 40 BUCK VOL2– 11 18 VOL3– RR 18 PGND2
LEVEL LEVEL OUT RR- 19
RFO 87 RF 39 BUS3 SHIFT SHIFT
38 BUS2 VOL2+ 12 17 VOL3+
PNSEL 88 CPU
ADDRESS CIRCUIT I/F 37 BUS1 20 VP1
36 BUS0 OUT FR+ 21
EQSET 89
35 VSS15 VO1– 13 16 VOL4– STANDBY
FR MUTE 22 STB
RVDD3 90 RAM LEVEL LEVEL
DIGITAL EQ 34 VDDM SHIFT SHIFT OUT FR- 23
LDO 91 VO1+ 14 15 VOL4+
APC AUTO ADJ. 33 VDD3 CHIP DETECT
ROM
MDI 92 32 DIAGNOSTIC 24 PGND1
VSS3
RVSS3 93 31 DVSS3 TEMPERATURE
DIAG 25 PROTECTION ENABLE
FNI2 94 LOGIC
SERVO
FNI1 95 26 RST
FE CONTROL 30 LO
FPI2 96
FPI1 97 29 DVR SW2(ANT REM) 27 SWITCH
ANA.
1-BIT
LPF 28 DVDD3
DAC
TPI 98 SUBCODE
TE 27 RO 28 CRES
DEMODULATION
TNI 99 CIRCUIT CLOCK SW1(ANT REM) 29 SWITCH
10-BIT 5-BIT 26 DVSS3
PWM GEN. 30 REG1(AUDIO +B)
SAR ADC R-2R DAC
FTE 100
REGULATOR
REG3(SERVO) 31
32 GND(REG)
REG4(DR+B) 33
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 34 REG5(ILL)
VP(REG) 35
RFZI
AVSS3
RFRP
FEI
SBAD/RFDC
TEI
TEZI
AVDD3
FOO
TRO
VREF
FMO
DMO
SBSY
SBOK
IPF
SFSY
ZDET
GPIN
VDD15
VSS15
XVSS3
XI
XO
XVDD3
REFERENCE 36 CBU
VOLTAGE
LOADDUMP BACK-UP
REG2(BU 5V) 37 REGULATOR PROTECTION SWITCH
IC6 R1114N151D-TR-FA (SERVO Board (1/2)) IC601 BA8271F-E2 (MAIN Board (1/2)) IC50 TDA7333013TR (MAIN Board (1/2))
BUS ON 1 BUS ON 14 VCC

SWITCH 3
VDD 1 5 VOUT
RESET INTERPOLATOR BAND PASS SINC4 SIGMA DELTA
RST 2 13 RESET 16 MPX
SWITCH FILTER FILTER CONVERTER
12 BUS ON VDDA 1
SINC4REG
11 CLK IN 15 INTN
MPX
BATTERY
BATT 3 10 BU IN
SWITCH REF3 2
REF2 3 SDAOUT
GND 2 RAM SDAIN 14 CSN
CLK 4 RDS RDSREG BUFFER 2 TEST LOGIC
VREF 5 REF1 4 INTN DEMODULATOR & I C/SPI SCK 13 SA_DATAOUT
CURRENT & &
VREF DATA 6 9 DATA IN SYNCHRONIZATION INTERFACE SPI 12 SDA_DATAIN
LIMIT CONTROL PIN MUX'S
TESTREG 11 SCL_CLK
LOGIC
VSS 5
GND 7 8 DATA OUT
TM 6 2
CE 3 4 NC
10 XTO
OSCILLATOR
VDDD 7 9 XTI
RESETN 8
CDX-R5515X/R5610/R6550
36 36
CDX-R5515X/R5610/R6550
IC401 TDA7419TR (MAIN Board (1/2))
MIX MIX
HPF
HPF
MONO FADER
MONO FADER
MONO FADER
MONO FADER
MONO FADER
MONO FADER
SOFTSEP
SOFTSEP
SOFTSEP
SOFTSEP
SOFTSEP
SOFTSEP
ACOUTR 1
ACINR 2
ACINL 3
SUBWOOFER
ACOUTL 4 L.P.F
BUSS
28 OUTRR2
MIDDLE 27 VREF
26 SAOUT
SPECTRUM
ANALYZER
25 SAIN
AC2INL 5
AC2INR 6
24 VDD
DIGITAL CONTROL I2C BUS

TREBLE 23 SDA
22 SCL
SOFTSTEP
VOLUME
SOFT
MUTE
LOUDNESS
21 MUTE
20 OUTLF
19 OUTLR1
18 OUTRR1
17 OUTRF
IN GAIN 16 OUTLR2
AUTO ZERO
15 GND
SE2L 7 SUPPLY
SE2R 8
SE1L 9
INPUT
SE1R 10 MULTIPLEXER
DIFFL 11
DIFFG 12
DIFFR 13
CREF 14
37
CDX-R5515X/R5610/R6550
• IC PIN DESCRIPTIONS
• IC3 MB90487APFV-G-131-BNDE1 (CD SYSTEM CONTROL) (SERVO BOARD (2/2))
Pin No. Pin Name I/O Pin Description
1 NC O Servo 1.5 V power supply control signal output
2 to 6 NC — Not used. (Open)
7 CD BUS0 I/O Bus data signal input/output 0
9 VSS — Ground pin
12 CD BUCK O Bus clock signal output
13 CD XCCE O Chip enable signal output
14 CD XRST O Reset signal output
15 CD ZDET I Zero detection signal input
21 VCC — Power supply pin (+3.3 V)
22 DAC ZDETL I Zero data detection signal input (L-ch)
23 DAC ZDETR I Zero data detection signal input (R-ch)
24 NC — Not used. (Open)
25 RXD I UART RXD data signal input (MCBUS/Flash data input)
26 TXD O UART TXD data signal output (MCBUS/Flash data output)
27 DEC SSTBY O SRAM STANDBY mode control signal output
28, 29 NC — Not used. (Open)
30 DEC INT I Request signal input
33 AVCC — Power supply pin (+3.3 V) for A/D converter
34 AVRH — External reference voltage for A/D converter
35 AVSS — Ground pin
37 DEC XMUTE O Mute signal output L: mute
42 MEC LIMIT I Sled limit in detection switch signal input
43 MEC LOAD O Loading motor signal output (Load direction)
44 MEC EJECT O Loading motor signal output (Eject direction)
45 MEC INSW I Pack-in detection signal input
46 MEC DSW I Chucking end detection switch signal input
47, 48 MD0, MD1 I CPU operation mode designation signal input (Connect to Vcc.)
49 MD2 I CPU operation mode designation signal input (Connect to Vss.)
50 BUS ON I Bus on signal input L: bus on
51 BU IN I Backup on/off signal input H: backup on, L: backup off
52 CD SBSY I SUBQ sync signal input L: interruption
53 MEC SELFSW I Disc insert detection switch signal input L: disc in interruption
56 UNISI I Serial data signal input
57 UNISO O Serial data signal output
58 UNICKI I Serial clock signal input
59 LINEOFF O Line off signal output
60 A ATT O Audio attenuation signal output H: ATT on
61 EJECT OK I Front panel open signal input H: eject
62 OPEN REQ O Front panel open/close request signal output H: open request
63 MECON O Mechanism deck power supply control signal output
64 CDON O Servo power supply control signal output
38
CDX-R5515X/R5610/R6550

65 XUART I Sony-Bus/MC-Bus change signal input H: Sony-Bus, L: MC-Bus
66 ZMUTE O Zero detection mute signal output
67 MECON CHK I MECON rising detection signal input
68 CDON CHK I CDON rising detection signal input
75 RSTX I System reset signal input
77 X1A — Sub-clock connect pin Not used in this set. (Open)
78 X0A — Sub-clock connect pin Not used in this set. (Connect to Vss.)
80 X0 I Main-clock connect pin (12 MHz)
81 X1 O Main-clock connect pin (12 MHz)
82 VCC — Power supply pin (+3.3 V)
83 XTS I Not used in this set. (Open)
84 XINIT3 I Not used in this set. (Open)
86 XSJIG I Not used in this set. (Open)
87 to 89 XINIT0 to 2 I Not used in this set. (Open)
98 XLINE I Not used in this set. (Open)
39
CDX-R5515X/R5610/R6550
• IC501 MB90488BPF-G-119-BNDE1 (SYSTEM CONTROL) (MAIN BOARD (2/2))

1 AREA SEL2 I Destination setting pin
4 NCO I Not used
5 BEEP O Beep signal output
6 NCO I Not used
7 NOSE SW I Front panel open/close detect signal input
8 DIAG I Power AMP status signal input
9 VOL ATT O Electronic volume attenuate control signal output
10 NCO O Not used
11 VSS — Ground
12 TU ATT O Tuner mute control signal output
13 NS MASK O Noise mask signal output
14 ILLUMI SEL1 I Illumination voltage setting pin
15 ILLUMI SEL2 I Illumination voltage setting pin
16 NCO O Not used
17 AUX IN O Not used
18 NCO O Not used
19 NCO O Not used
20 NCO O Not used
21 NCO O Not used
22 NCO O Not used
23 VCC5 — Power supply pin (+3.3V)
24 EEP SIO I/O EEPROM bus serial data input/output
25 EEP CKO O EEPROM bus serial clock output
26 AMP STB O Power AMP satandby signal output
27 LCD CE O LCD driver chip enable output
28 LCD SO O LCD driver serial data output
29 LCD SCK O LCD driver serial clock output
30 RDS ON O RDS ON signal output
31 NCO O Not used
32 NCO O Not used
33 I2C SCK O I2C bus serial clock output
34 I2C SIO I/O I2C bus serial data input/output
35 DAVDD — A/D converter power supply pin (+3.3V)
36 AVRH — A/D converter reference power supply pin (+3.3V)
37 DAVSS — Ground
38 QUALITY I Noise detect signal input
39 VSM I S-meter voltage detect signal input
40 KEY IN1 I Key signal input
41 KEY IN0 I Key signal input
42 VSS — Ground
43 RC IN0 I Rotary commander key signal input
44 SA_IN I Spectrum analyzer data signal input
45 SA_CKO O Spectrum analyzer clock signal output
46 NCO O Not used
47 NCO O Not used
48 NCO O Not used
49 MD0 I Operation mode setting pin
52 KEY ACK I Key acknowledgment detect signal input
40
CDX-R5515X/R5610/R6550

53 TU ATT IN I Tuner mute zero cross detect signal input
54 BU IN I Back-up power supply detect signal input
55 NCO O Not used
56 DAVN I RDS data block synchronized detect signal input
57 NCO O Not used
58 UNI SI I SONY bus data input
59 UNI SO O SONY bus data output
60 UNI SCK O SONY bus clock output
61 NCO O Not used
62 NCO O Not used
63 NCO O Not used
64 SIRCS I Remote control signal input
65 NCO O Not used
66 NCO O Not used
67 NCO O Not used
68 FLASH W I Memory mode select signal input
69 NCO O Not used
70 SYNCHRO SW I Synchro CD door open/close detect signal input
71 RC IN1 I Rotary commander shift key signal input
72 ACC IN I Accessory power supply detect signal input
73 TEST IN I Test mode detect signal input
74 TEL ATT I Telephone attenuate detect signal input
75 ILLU IN I Illumination detect signal input
76 XKEY ON O A/D converter power supply control signal output
77 RESET I CPU reset input
78 NCO O Not used
79 XIN — Sub-clock input (32.768kHz)
80 XOUT — Sub-clock output (32.768kHz)
81 VSS1 — Ground
82 OSC IN — Main-clock input (3.68MHz)
83 OSC OUT — Main-clock output (3.68MHz)
84 VCC3 — Power supply pin (+3.3V)
85 DEMO SEL I Demo select signal input
86 ATT O Audio mute control signal output
87 BUS ON O Bus ON signal output
88 SYS RST O System reset output
89 EJECT OK SW O Eject OK signal output
90 NCO O Not used
91 NCO O Not used
92 NCO O Not used
93 Z-MUTE I Z-Mute signal input
94 NCO O Not used
95 NCO O Not used
96 NCO O Not used
97 NCO O Not used
98 CD ON I CD servo power control request signal input
99 CDM ON I CD deck power control request signal input
100 NCO O Not used
41
CDX-R5515X/R5610/R6550
SECTION 4
EXPLODED VIEWS
NOTE:
• The mechanical parts with no reference • Color Indication of Appearance Parts The components identified by
number in the exploded views are not supplied. Example : mark 0 or dotted line with mark
• Items marked “*” are not stocked since KNOB, BALANCE (WHITE) ... (RED) 0 are critical for safety.
they are seldom required for routine service. R R Replace only with part number
Some delay should be anticipated Parts Color Cabinet’s Color specified.
when ordering these items. • Accessories are given in the last of this
• -XX and -X mean standardized parts, so parts list. Les composants identifiés par une
they may have some difference from the marque 0 sont critiques pour
original one. la sécurité.
Ne les remplacer que par une piéce
portant le numéro spécifié.
4-1. MAIN SECTION

A
MG-611TA-186//K #2
#1
not supplied
B
6
A
F901
5 #3
4
7
3 8
#1
TU1
not supplied
2
#1
not supplied
#1
Ref. No. Part No. Description Remark Ref. No. Part No. Description Remark
1 X-2023-967-1 PANEL (LCD) ASSY, SUB 7 2-345-298-01 PLATE (TU), GROUND
2 2-583-939-01 SCREW (+B 2X4) 8 A-1084-640-A MAIN BOARD, COMPLETE (R6550)
3 X-2024-365-1 LOCK ASSY (S) 8 A-1085-702-A MAIN BOARD, COMPLETE (R5610)
4 3-246-006-31 COVER 8 A-1085-863-A MAIN BOARD, COMPLETE (R5515X)
5 2-583-940-01 SCREW (+BTT) F901 1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) 10A
6 1-776-207-72 CORD (WITH CONNECTOR) (POWER) TU1 A-3220-961-A TUNER UNIT (TUX-032)
(R5515X/R5610) #1 7-685-792-09 SCREW +PTT 2.6X6 (S)
6 1-776-527-71 CORD (WITH CONNECTOR) (ISO) (POWER) #2 7-685-790-01 SCREW +PTT 2.6X4 (S)
(R6550) #3 7-685-793-09 SCREW +PTT 2.6X8 (S)
42
CDX-R5515X/R5610/R6550
4-2. FRONT PANEL SECTION
70
71
66 #4
#4
56
not supplied not supplied

65 (KEY board) 69
56 LCD901
not supplied 56
64
68
63 not
C supplied
not supplied not supplied
(DISPLAY board)
61 62
67 52
60 not supplied
57 58
not supplied 51
not supplied D
(PRESET board) not supplied
59 54
56 C
not supplied 53
55 not supplied
not supplied
51 X-2024-701-1 BUTTON ASSY (S) (R6550) 62 2-187-133-01 PLATE (SLOT), LIGHT GUIDE
51 X-2024-814-1 BUTTON ASSY (S) (R5515X/R5610) 63 2-187-154-11 SPRING (M)
52 2-349-626-01 SPRING (RELEASE) 64 2-187-132-01 BRACKET (DISPLAY)
53 2-187-131-01 FILTER (IR) 65 2-187-154-01 SPRING (M)
54 2-187-126-01 PANEL, FRONT 66 2-187-127-01 PANEL (LCD), FRONT BACK
55 2-187-149-01 COVER (PRESET) (R6550) 67 1-780-201-11 CONDUCTIVE BOARD, CONNECTION

55 2-187-149-11 COVER (PRESET) (R5610) 68 1-830-259-11 CABLE, FLEXIBLE FLAT (12 CORE)
55 2-187-149-21 COVER (PRESET) (R5515X) 69 2-187-139-01 COVER (PWB)
56 3-250-543-41 SCREW (+B P-TITE M2) 70 X-2050-189-1 CASE ASSY (for FRONT PANEL)
57 1-830-258-11 CABLE, FLEXIBLE FLAT (6 CORE) 71 A-1084-642-A PANEL COMPLETE ASSY, FRONT (R6550)
58 2-187-147-01 ARM (PRESET) 71 A-1085-704-A PANEL COMPLETE ASSY, FRONT (R5610)

59 2-187-153-11 SPRING (S) 71 A-1085-925-A PANEL COMPLETE ASSY, FRONT (R5515X)
60 X-2024-702-1 DISPLAY (SV) ASSY (R6550) LCD901 1-805-736-11 DISPLAY PANEL, LIQUID CRYSTAL
60 X-2024-815-1 DISPLAY (SV) ASSY (R5610) (R5610/R6550)
60 X-2024-873-1 DISPLAY (SV) ASSY (R5515X) LCD901 1-805-737-11 DISPLAY PANEL, LIQUID CRYSTAL (R5515X)
#4 7-685-105-19 SCREW +P 2X8 TYPE2 NON-SLIT
61 2-187-153-01 SPRING (S)
43
CDX-R5515X/R5610/R6550
4-3. CD MECHANISM SECTION (1)

(MG-611TA-186//K)
not supplied
102 (SENSOR board)
101
not supplied
#5
not supplied
not supplied
not supplied
103
104
106
105
108
107
101 A-3372-455-A CHASSIS (T) SUB ASSY 106 3-253-748-01 DAMPER (S)
102 3-253-729-01 SPRING (LTR), TENSION COIL 107 3-352-758-31 SCREW (M1.7), TOOTHED LOCK
103 3-253-746-14 SPRING (DAMPER), COMPRESSION 108 A-1075-784-A SERVO BOARD, COMPLETE
104 3-253-746-03 SPRING (DAMPER), COMPRESSION #5 7-627-552-87 SCREW, PRECISION +P 1.7X2.2
105 2-345-767-01 SPRING (KF60), TENSION
44
CDX-R5515X/R5610/R6550

(MG-611TA-186//K)
155
156
157
154
(including M901)
#6
M902
SW4
not supplied
not supplied
158
153
not supplied
not supplied
152
151
The components identified by Les composants identifiés par

mark 0 or dotted line with mark une marque 0 sont critiques
0 are critical for safety. pour la sécurité.
Replace only with part number Ne les remplacer que par une
specified. piéce portant le numéro spécifié.
151 A-1075-786-A CHASSIS (OP) COMPLETE ASSY 157 X-3383-454-3 LEVER (SL) ASSY
152 3-316-938-91 SCREW (B1.4X5), TAPPING 158 3-261-959-02 SPRING (SL), TORSION
0 153 8-820-207-12 OPTICAL PICK-UP (KSS1000E/K1RP) M902 A-3337-638-A MOTOR ASSY, SL (SLED)
154 A-1075-787-A CHASSIS (OP) SUB ASSY (including M901) SW4 1-571-099-11 SWITCH (1 KEY) (LIMIT)
155 A-3337-641-A ARM SUB ASSY, CHUCKING #6 7-627-850-77 SCREW, PRECISION +P 1.4X1.8
156 A-3337-639-A LEVER (SL) SUB ASSY
45
CDX-R5515X/R5610/R6550

(MG-611TA-186//K)
201 203
202
207
211
204
209
208 210 205
207
207
M903
#5
206
201 3-262-755-01 WASHER (1.1-2.5) 208 2-186-696-11 BRACKET (LEM-N)
202 2-186-699-11 GEAR (RA1) 209 3-345-648-91 SCREW (M1.4), TOOTHED LOCK
203 A-1075-789-A ARM ASSY, ROLLER 210 A-1083-637-A GEAR (LE) ASSY
204 3-259-455-02 SPRING (RAL) 211 2-186-697-11 BEARING (LEB-N)
205 3-253-713-01 SPRING (RAR) M903 A-1075-792-A MOTOR ASSY, LE (LOADING)
206 3-259-469-01 SPRING (LE), LEAF #5 7-627-552-87 SCREW, PRECISION +P 1.7X2.2

207 2-134-636-31 SCREW (M1.7X2.5)
46
CDX-R5515X/R5610/R6550

(MG-611TA-186//K)
254
252
255
252
256
251 253
257
251 2-186-700-11 GEAR (CHK1) 255 3-899-829-01 WASHER (SLIT)
252 3-344-223-01 WASHER 256 3-259-032-01 GEAR (LE2)
253 3-259-470-01 GEAR (LE1) 257 A-1075-791-A CHASSIS (M) BLOCK ASSY
254 3-253-755-02 LEVER (D)
47
CDX-R5515X/R5610/R6550
SECTION 5
DISPLAY
ELECTRICAL PARTS LIST
NOTE:
• Due to standardization, replacements in • Items marked “*” are not stocked since The components identified by
the parts list may be different from the they are seldom required for routine service. mark 0 or dotted line with mark
parts specified in the diagrams or the Some delay should be anticipated 0 are critical for safety.
components used on the set. when ordering these items. Replace only with part number
• -XX and -X mean standardized parts, so • SEMICONDUCTORS specified.
they may have some difference from the In each case, u : µ, for example:
original one. uA.. : µA.. uPA.. : µPA.. Les composants identifiés par une
• RESISTORS uPB.. : µPB.. uPC..: µPC.. uPD.. : µPD.. marque 0 sont critiques pour
All resistors are in ohms. • CAPACITORS la sécurité.
METAL:Metal-film resistor. uF : µF Ne les remplacer que par une piéce
METAL OXIDE: Metal oxide-film resistor. • COILS portant le numéro spécifié.
F:nonflammable uH : µH
When indicating parts by reference

number, please include the board.
DISPLAY BOARD LSW920 1-786-807-11 SWITCH, TACTILE (WITH LED) (SEL) (R5515X)
************** LSW921 1-786-805-11 SWITCH, TACTILE (WITH LED) (DSPL)
(R5610/R6550)
1-780-201-11 CONDUCTIVE BOARD, CONNECTION LSW921 1-786-807-11 SWITCH, TACTILE (WITH LED) (DSPL)
(R5515X)
< CAPACITOR >
< TRANSISTOR >
C981 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V
C982 1-164-227-11 CERAMIC CHIP 0.022uF 10% 25V Q925 8-729-027-58 TRANSISTOR DTC143ZKA-T146
C984 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V < RESISTOR >
R917 1-216-823-11 METAL CHIP 1.5K 5% 1/10W
< CONNECTOR > R918 1-216-823-11 METAL CHIP 1.5K 5% 1/10W
R919 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
CN904 1-818-969-21 CONNECTOR, FFC/FPC (ZIF) 12P R920 1-216-827-11 METAL CHIP 3.3K 5% 1/10W
R924 1-216-805-11 METAL CHIP 47 5% 1/10W
< DIODE > (R5610/R6550)
D984 8-719-988-61 DIODE 1SS355TE-17 R924 1-216-807-11 METAL CHIP 68 5% 1/10W

(R5515X)
< IC > R925 1-216-805-11 METAL CHIP 47 5% 1/10W
(R5610/R6550)
IC901 6-707-064-01 IC LC75876WH-US-E R925 1-216-807-11 METAL CHIP 68 5% 1/10W
(R5515X)
< LIQUID CRYSTAL DISPLAY > R926 1-216-804-11 METAL CHIP 39 5% 1/10W
(R5610/R6550)
LCD901 1-805-736-11 DISPLAY PANEL, LIQUID CRYSTAL R926 1-216-807-11 METAL CHIP 68 5% 1/10W
(R5610/R6550) (R5515X)
LCD901 1-805-737-11 DISPLAY PANEL, LIQUID CRYSTAL (R5515X)
R953 1-216-809-11 METAL CHIP 100 5% 1/10W
< DIODE > R954 1-216-809-11 METAL CHIP 100 5% 1/10W
R955 1-216-809-11 METAL CHIP 100 5% 1/10W
LED931 6-501-062-01 LED NSCW505CT-AST (LCD BACK LIGHT) (R5515X)
LED932 6-501-062-01 LED NSCW505CT-AST (LCD BACK LIGHT) R955 1-216-810-11 METAL CHIP 120 5% 1/10W
LED961 6-500-895-01 LED CL-270UB2-X-TS (CD SLOT) (R5515X) (R5610/R6550)
LED961 8-719-082-38 LED CL-270SR-C-TS (CD SLOT) R960 1-216-809-11 METAL CHIP 100 5% 1/10W
(R5610/R6550)
R961 1-216-809-11 METAL CHIP 100 5% 1/10W
< SWITCH > R962 1-216-809-11 METAL CHIP 100 5% 1/10W
(R5515X)
LSW901 1-786-805-11 SWITCH, TACTILE (WITH LED) (Z) R962 1-216-810-11 METAL CHIP 120 5% 1/10W
(R5610/R6550) (R5610/R6550)
LSW901 1-786-807-11 SWITCH, TACTILE (WITH LED) (Z) (R5515X) R964 1-216-809-11 METAL CHIP 100 5% 1/10W
LSW918 1-786-805-11 SWITCH, TACTILE (WITH LED) (DSO) R965 1-216-809-11 METAL CHIP 100 5% 1/10W
(R5610/R6550)
LSW918 1-786-807-11 SWITCH, TACTILE (WITH LED) (DSO) (R5515X) R966 1-216-809-11 METAL CHIP 100 5% 1/10W
LSW919 1-786-805-11 SWITCH, TACTILE (WITH LED) (EQ3) (R5515X)
(R5610/R6550) R966 1-216-810-11 METAL CHIP 120 5% 1/10W
(R5610/R6550)
LSW919 1-786-807-11 SWITCH, TACTILE (WITH LED) (EQ3)(R5515X) R969 1-216-815-11 METAL CHIP 330 5% 1/10W
LSW920 1-786-805-11 SWITCH, TACTILE (WITH LED) (SEL) (R5610/R6550)
(R5610/R6550)
48
CDX-R5515X/R5610/R6550
DISPLAY KEY
R969 1-216-817-11 METAL CHIP 470 5% 1/10W R902 1-216-819-11 METAL CHIP 680 5% 1/10W
(R5515X) R913 1-216-819-11 METAL CHIP 680 5% 1/10W
R982 1-216-809-11 METAL CHIP 100 5% 1/10W R916 1-216-821-11 METAL CHIP 1K 5% 1/10W
R983 1-216-864-11 SHORT CHIP 0
R943 1-216-809-11 METAL CHIP 100 5% 1/10W
R987 1-216-857-11 METAL CHIP 1M 5% 1/10W (R5610/R6550)
************************************************************* R943 1-216-811-11 METAL CHIP 150 5% 1/10W
(R5515X)
KEY BOARD R944 1-216-811-11 METAL CHIP 150 5% 1/10W
********** (R5515X)
R945 1-216-811-11 METAL CHIP 150 5% 1/10W
< CAPACITOR > (R5515X)
R946 1-216-813-11 METAL CHIP 220 5% 1/10W
C973 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V (R5515X)
< CONNECTOR > R946 1-216-864-11 SHORT CHIP 0 (R5610/R6550)

R947 1-216-809-11 METAL CHIP 100 5% 1/10W
CN901 1-794-312-11 PIN, CONNECTOR 12P (R5610/R6550)
CN902 1-818-969-21 CONNECTOR, FFC/FPC (ZIF) 12P R947 1-216-815-11 METAL CHIP 330 5% 1/10W
CN903 1-785-616-11 CONNECTOR, FPC (0.5mm PITCH) 6P (R5515X)
R948 1-216-809-11 METAL CHIP 100 5% 1/10W
< DIODE > (R5610/R6550)
R948 1-216-811-11 METAL CHIP 150 5% 1/10W
D902 8-719-083-66 DIODE UDZSTE-1718B (R5515X)
D903 8-719-978-33 DIODE DTZ-TT11-6.8B
D906 6-500-886-01 DIODE RSA6.1ENTR R949 1-216-811-11 METAL CHIP 150 5% 1/10W
D962 8-719-060-48 DIODE RB751V-40TE-17 (R5515X)
D963 8-719-083-66 DIODE UDZSTE-1718B R950 1-216-811-11 METAL CHIP 150 5% 1/10W
(R5515X)
D981 8-719-069-56 DIODE UDZSTE-176.2B R951 1-216-813-11 METAL CHIP 220 5% 1/10W
(R5515X)
< IC > R951 1-216-864-11 SHORT CHIP 0 (R5610/R6550)
R952 1-216-809-11 METAL CHIP 100 5% 1/10W
IC972 6-600-163-01 IC RS-770 (IR) (R5610/R6550)
< JUMPER RESISTOR > R952 1-216-815-11 METAL CHIP 330 5% 1/10W
(R5515X)
JP941 1-216-864-11 SHORT CHIP 0 (R5610/R6550) R972 1-216-809-11 METAL CHIP 100 5% 1/10W
JP942 1-216-864-11 SHORT CHIP 0 (R5610/R6550) R973 1-216-810-11 METAL CHIP 120 5% 1/10W
(R5610/R6550)
< DIODE > R973 1-216-811-11 METAL CHIP 150 5% 1/10W
(R5515X)
LED902 6-500-204-01 LED CL-190UB2-X-T (OFF) (R5515X) R974 1-216-809-11 METAL CHIP 100 5% 1/10W
LED902 6-500-450-01 LED CL-195SR-CD-T (OFF) (R5610/R6550) (R5610/R6550)
LED914 6-500-204-01 LED CL-190UB2-X-T (ATT) (R5515X)
LED914 6-500-450-01 LED CL-195SR-CD-T (ATT) (R5610/R6550) R974 1-216-811-11 METAL CHIP 150 5% 1/10W
LED915 6-500-204-01 LED CL-190UB2-X-T (VOL +) (R5515X) (R5515X)
R975 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
LED915 6-500-450-01 LED
CL-195SR-CD-T (VOL +) (R5610/R6550) R976 1-216-819-11 METAL CHIP 680 5% 1/10W
LED916 6-500-204-01 LED
CL-190UB2-X-T (VOL –) (R5515X) R990 1-216-809-11 METAL CHIP 100 5% 1/10W
LED916 6-500-450-01 LED
CL-195SR-CD-T (VOL –) (R5610/R6550)
LED917 6-500-204-01 LED
CL-190UB2-X-T (SEEK +/> M) < SWITCH >
(R5515X)
LED917 6-500-450-01 LED CL-195SR-CD-T (SEEK +/> M) S902 1-786-653-11 SWITCH, TACTILE (OFF)
(R5610/R6550) S914 1-786-653-11 SWITCH, TACTILE (ATT)
S915 1-786-653-11 SWITCH, TACTILE (VOL +)
LED918 6-500-204-01 LED CL-190UB2-X-T (SEEK –/m .) S916 1-786-653-11 SWITCH, TACTILE (VOL –)
(R5515X) S917 1-786-653-11 SWITCH, TACTILE (SEEK +/> M)
LED918 6-500-450-01 LED CL-195SR-CD-T (SEEK –/m .)
(R5610/R6550) S918 1-786-653-11 SWITCH, TACTILE (SEEK –/m .)
S961 1-529-566-61 SWITCH, PUSH (1 KEY) (NOSE DET)
< RESISTOR > *************************************************************
R901 1-216-819-11 METAL CHIP 680 5% 1/10W
49
CDX-R5515X/R5610/R6550
MAIN
A-1084-640-A MAIN BOARD, COMPLETE (R6550) C315 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
A-1085-702-A MAIN BOARD, COMPLETE (R5610) C316 1-104-665-11 ELECT 100uF 20% 25V
A-1085-863-A MAIN BOARD, COMPLETE (R5515X) C317 1-126-961-11 ELECT 2.2uF 20% 50V
********************* C318 1-162-923-11 CERAMIC CHIP 47PF 5% 50V
7-621-284-40 SCREW +P 2.6X10
7-685-134-19 SCREW +P 2.6X8 TYPE2 NON-SLIT C320 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
7-685-793-09 SCREW +PTT 2.6X8 (S) C323 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25V
7-685-795-09 SCREW +PTT 2.6X12 (S) C324 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25V
C329 1-165-319-11 CERAMIC CHIP 0.1uF 50V
< CAPACITOR > C361 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16V
C1 1-126-963-11 ELECT 4.7uF 20% 50V C362 1-127-715-11 CERAMIC CHIP 0.22uF 10% 16V
(R6550) C363 1-124-717-85 ELECT 1uF 20% 50V
C2 1-126-947-11 ELECT 47uF 20% 35V (R5515X)
C3 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C363 1-126-960-11 ELECT 1uF 20% 50V
C5 1-126-947-11 ELECT 47uF 20% 35V (R5610/R6550)
(R5515X)
C9 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V (R5610/R6550)
C14 1-162-927-11 CERAMIC CHIP 100PF 5% 50V
(R5515X) C365 1-126-960-11 ELECT 1uF 20% 50V
C14 1-164-230-11 CERAMIC CHIP 220PF 5% 50V C367 1-126-960-11 ELECT 1uF 20% 50V
(R6550) C401 1-104-665-11 ELECT 100uF 20% 25V
C50 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C402 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
(R6550) C403 1-104-665-11 ELECT 100uF 20% 25V
(R5610/R6550)
(R6550) C403 1-124-673-85 ELECT 100uF 20% 10V
C52 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V (R5515X)
(R6550) C405 1-128-551-11 ELECT 22uF 20% 63V
(R6550) C413 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C54 1-107-826-11 CERAMIC CHIP 0.1uF 10% 16V C414 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
(R6550)
(R6550) C417 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V
C56 1-162-917-11 CERAMIC CHIP 15PF 5% 50V C419 1-162-966-11 CERAMIC CHIP 0.0022uF 10% 50V
(R6550) C421 1-124-721-85 ELECT 10uF 20% 50V
C57 1-162-917-11 CERAMIC CHIP 15PF 5% 50V (R5515X)
(R6550)
C58 1-162-959-11 CERAMIC CHIP 330PF 5% 50V C421 1-126-964-11 ELECT 10uF 20% 50V
(R6550) (R5610/R6550)
C60 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V C422 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
(R6550) C423 1-107-823-11 CERAMIC CHIP 0.47uF 10% 16V
C61 1-126-947-11 ELECT 47uF 20% 35V C431 1-126-964-11 ELECT 10uF 20% 50V
(R6550) C432 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
(R6550) (R5515X)
C303 1-128-551-11 ELECT 22uF 20% 63V (R5610/R6550)
(R5610/R6550) C442 1-163-251-11 CERAMIC CHIP 100PF 5% 50V
C303 1-124-695-85 ELECT 22uF 20% 25V C443 1-107-823-11 CERAMIC CHIP 0.47uF 10% 16V
(R5515X) C451 1-126-964-11 ELECT 10uF 20% 50V
C306 1-126-964-11 ELECT 10uF 20% 50V (R5515X)
C308 1-126-964-11 ELECT 10uF 20% 50V (R5610/R6550)
C471 1-124-721-85 ELECT 10uF 20% 50V
C310 1-126-916-11 ELECT 1000uF 20% 6.3V (R5515X)
C314 1-126-964-11 ELECT 10uF 20% 50V (R5610/R6550)
50
CDX-R5515X/R5610/R6550
MAIN
C472 1-107-823-11 CERAMIC CHIP 0.47uF 10% 16V D304 6-500-522-01 DIODE 10EDB40-TA1B2
C480 1-136-154-00 FILM 0.012uF 5% 50V D305 6-500-522-01 DIODE 10EDB40-TA1B2
C481 1-136-154-00 FILM 0.012uF 5% 50V D306 6-500-522-01 DIODE 10EDB40-TA1B2
C485 1-104-665-11 ELECT 100uF 20% 25V D310 6-500-522-01 DIODE 10EDB40-TA1B2
(R5610/R6550) D311 6-500-522-01 DIODE 10EDB40-TA1B2
C485 1-124-673-85 ELECT 100uF 20% 10V D312 6-500-522-01 DIODE 10EDB40-TA1B2
(R5515X) D400 6-501-013-01 DIODE BAT54ALT1G
C486 1-124-721-85 ELECT 10uF 20% 50V
(R5515X) D491 8-719-988-61 DIODE 1SS355TE-17
C486 1-126-964-11 ELECT 10uF 20% 50V D493 6-501-051-01 DIODE BAT54CLT1G
(R5610/R6550) D501 8-719-914-44 DIODE DAP202K
D502 8-719-060-48 DIODE RB751V-40TE-17
C491 1-126-947-11 ELECT 47uF 20% 35V D511 6-501-051-01 DIODE BAT54CLT1G
C501 1-126-924-11 ELECT 330uF 20% 10V
C502 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V D602 8-719-083-66 DIODE UDZSTE-1718B
C503 1-104-665-11 ELECT 100uF 20% 25V D603 8-719-069-56 DIODE UDZSTE-176.2B
D605 8-719-083-66 DIODE UDZSTE-1718B
C505 1-104-665-11 ELECT 100uF 20% 25V D606 8-719-060-48 DIODE RB751V-40TE-17
C507 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V D607 8-719-049-38 DIODE 1N5404TU
(R6550) D702 8-719-083-66 DIODE UDZSTE-1718B
C508 1-216-864-11 SHORT CHIP 0 (R5515X/R5610) D703 8-719-978-33 DIODE DTZ-TT11-6.8B
D704 8-719-083-66 DIODE UDZSTE-1718B
C510 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V D705 8-719-988-61 DIODE 1SS355TE-17
C512 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V < FERRITE BEAD >
FB401 1-216-295-11 SHORT CHIP 0
C514 1-162-964-11 CERAMIC CHIP 0.001uF 10% 50V FB402 1-216-864-11 SHORT CHIP 0
C515 1-162-917-11 CERAMIC CHIP 15PF 5% 50V FB403 1-469-876-11 INDUCTOR, FERRITE BEAD
C516 1-162-917-11 CERAMIC CHIP 15PF 5% 50V FB404 1-216-295-11 SHORT CHIP 0
C519 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V FB405 1-216-864-11 SHORT CHIP 0
C600 1-126-935-11 ELECT 470uF 20% 16V
FB406 1-216-864-11 SHORT CHIP 0
C601 1-162-970-11 CERAMIC CHIP 0.01uF 10% 25V FB407 1-500-245-11 INDUCTOR, FERRITE BEAD
C701 1-112-302-11 ELECT 3300uF 20% 16V FB408 1-469-876-11 INDUCTOR, FERRITE BEAD
(R5515X)
C701 1-131-868-81 ELECT 3300uF 20% 16V < IC >
(R5610/R6550)
C702 1-126-960-11 ELECT 1uF 20% 50V IC50 6-803-747-01 IC TDA7333013TR (R6550)
C703 1-126-963-11 ELECT 4.7uF 20% 50V IC300 6-705-359-02 IC TDA8588AJ/N2/R1
IC401 6-707-303-01 IC TDA7419TR
C704 1-115-340-11 CERAMIC CHIP 0.22uF 10% 25V IC501 6-804-913-01 IC MB90488BPF-G-119-BNDE1
C901 1-163-009-11 CERAMIC CHIP 0.001uF 10% 50V IC502 6-705-373-01 IC MM3123DPLE
IC601 6-703-884-01 IC BA8271F-E2
< CONNECTOR > IC602 8-759-659-13 IC PST3428UL
CN101 1-794-311-21 PLUG, CONNECTOR 12P < JACK >

CN300 1-774-701-21 PIN, CONNECTOR 16P
CN350 1-817-536-11 CONNECTOR, BOARD TO BOARD 28P J1 1-815-185-13 JACK (ANTENNA)
CNJ400 1-580-907-41 PLUG, CONNECTOR (BUS CONTROL IN) J370 1-566-822-41 JACK (REMOTE IN)
J451 1-774-700-11 JACK, PIN 6P (BUS AUDIO IN,
< DIODE > AUDIO OUT REAR/FRONT)
D2 8-719-069-55 DIODE UDZSTE-175.6B < JUMPER RESISTOR >

D101 6-500-886-01 DIODE RSA6.1ENTR
D102 6-500-886-01 DIODE RSA6.1ENTR JC1 1-216-295-11 SHORT CHIP 0
D301 6-500-522-01 DIODE 10EDB40-TA1B2 JC3 1-216-864-11 SHORT CHIP 0
JC301 1-216-296-11 SHORT CHIP 0
51
CDX-R5515X/R5610/R6550
MAIN
JC350 1-216-296-11 SHORT CHIP 0 < RESISTOR >
JC360 1-216-864-11 SHORT CHIP 0
JC420 1-216-864-11 SHORT CHIP 0 R1 1-216-809-11 METAL CHIP 100 5% 1/10W
JC430 1-216-296-11 SHORT CHIP 0 (R6550)
JC490 1-216-296-11 SHORT CHIP 0 R2 1-216-839-11 METAL CHIP 33K 5% 1/10W
(R6550)
JC501 1-216-296-11 SHORT CHIP 0 (R6550)
JC504 1-216-864-11 SHORT CHIP 0
R6 1-414-595-11 INDUCTOR, FERRITE BEAD
JC505 1-216-864-11 SHORT CHIP 0 R7 1-414-595-11 INDUCTOR, FERRITE BEAD
JC506 1-216-864-11 SHORT CHIP 0 (R6550) R8 1-216-839-11 METAL CHIP 33K 5% 1/10W
JC507 1-216-864-11 SHORT CHIP 0 (R6550) (R6550)
JC509 1-216-296-11 SHORT CHIP 0 (R6550)
R10 1-216-821-11 METAL CHIP 1K 5% 1/10W
JC510 1-216-864-11 SHORT CHIP 0 (R6550)
JC511 1-216-296-11 SHORT CHIP 0 R11 1-216-864-11 SHORT CHIP 0 (R6550)
JC514 1-216-296-11 SHORT CHIP 0 R14 1-216-864-11 SHORT CHIP 0 (R6550)
R52 1-216-845-11 METAL CHIP 100K 5% 1/10W
JC515 1-216-864-11 SHORT CHIP 0 (R6550)
JC600 1-216-864-11 SHORT CHIP 0
JC998 1-216-864-11 SHORT CHIP 0 (R6550)
L1 1-216-295-11 SHORT CHIP 0 R54 1-414-595-11 INDUCTOR, FERRITE BEAD (R6550)
R55 1-414-595-11 INDUCTOR, FERRITE BEAD (R6550)
< COIL > R57 1-216-833-11 METAL CHIP 10K 5% 1/10W
(R6550)
L2 1-414-595-11 INDUCTOR, FERRITE BEAD (R6550) R58 1-216-821-11 METAL CHIP 1K 5% 1/10W
L3 1-414-595-11 INDUCTOR, FERRITE BEAD (R6550) (R6550)
L4 1-469-844-11 INDUCTOR 2.2uH
L300 1-456-617-11 COIL, CHOKE R102 1-216-864-11 SHORT CHIP 0
L301 1-469-876-11 INDUCTOR, FERRITE BEAD R103 1-216-817-11 METAL CHIP 470 5% 1/10W
R104 1-216-864-11 SHORT CHIP 0
L302 1-414-595-11 INDUCTOR, FERRITE BEAD R105 1-216-864-11 SHORT CHIP 0
L303 1-414-595-11 INDUCTOR, FERRITE BEAD R301 1-216-811-11 METAL CHIP 150 5% 1/10W
L400 1-216-295-11 SHORT CHIP 0
L401 1-469-844-11 INDUCTOR 2.2uH R302 1-216-841-11 METAL CHIP 47K 5% 1/10W
L500 1-469-844-11 INDUCTOR 2.2uH R351 1-216-845-11 METAL CHIP 100K 5% 1/10W
R355 1-216-833-11 METAL CHIP 10K 5% 1/10W
< TRANSISTOR > R356 1-216-833-11 METAL CHIP 10K 5% 1/10W
R357 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
Q1 8-729-027-43 TRANSISTOR DTC114EKA-T146 (R6550)
Q3 8-729-106-68 TRANSISTOR 2SD1615A-GP R358 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
Q50 8-729-600-22 TRANSISTOR 2SA1235-F (R6550) R359 1-216-864-11 SHORT CHIP 0
Q420 6-550-752-01 TRANSISTOR DTC614TKT146 R370 1-216-809-11 METAL CHIP 100 5% 1/10W
R400 1-216-789-11 METAL CHIP 2.2 5% 1/10W
Q440 6-550-752-01 TRANSISTOR DTC614TKT146
Q450 6-550-752-01 TRANSISTOR DTC614TKT146 R401 1-216-821-11 METAL CHIP 1K 5% 1/10W
Q460 6-550-752-01 TRANSISTOR DTC614TKT146 R402 1-216-821-11 METAL CHIP 1K 5% 1/10W
Q491 8-729-027-23 TRANSISTOR DTA114EKA-T146 R421 1-216-809-11 METAL CHIP 100 5% 1/10W
R422 1-216-841-11 METAL CHIP 47K 5% 1/10W
Q492 8-729-027-43 TRANSISTOR DTC114EKA-T146
Q501 8-729-027-23 TRANSISTOR DTA114EKA-T146 R423 1-216-864-11 SHORT CHIP 0
Q600 8-729-047-76 TRANSISTOR FMC2A-T148 R430 1-216-809-11 METAL CHIP 100 5% 1/10W
Q601 8-729-027-23 TRANSISTOR DTA114EKA-T146 R431 1-216-809-11 METAL CHIP 100 5% 1/10W
Q605 8-729-027-43 TRANSISTOR DTC114EKA-T146 R432 1-216-841-11 METAL CHIP 47K 5% 1/10W
R440 1-216-809-11 METAL CHIP 100 5% 1/10W
Q701 8-729-120-28 TRANSISTOR 2SC1623-L5L6
Q702 8-729-120-28 TRANSISTOR 2SC1623-L5L6 R441 1-216-809-11 METAL CHIP 100 5% 1/10W
Q703 8-729-120-28 TRANSISTOR 2SC1623-L5L6 R442 1-216-841-11 METAL CHIP 47K 5% 1/10W
R443 1-216-864-11 SHORT CHIP 0
R450 1-247-807-31 CARBON 100 5% 1/4W
52
CDX-R5515X/R5610/R6550
MAIN
R452 1-216-841-11 METAL CHIP 47K 5% 1/10W R538 1-216-864-11 SHORT CHIP 0 (R5515X/R5610)
R462 1-216-841-11 METAL CHIP 47K 5% 1/10W R541 1-216-841-11 METAL CHIP 47K 5% 1/10W
R463 1-216-864-11 SHORT CHIP 0 R542 1-216-845-11 METAL CHIP 100K 5% 1/10W
R470 1-216-809-11 METAL CHIP 100 5% 1/10W (R6550)
R473 1-216-864-11 SHORT CHIP 0 (R5610/R6550)
R545 1-216-845-11 METAL CHIP 100K 5% 1/10W
R480 1-216-833-11 METAL CHIP 10K 5% 1/10W (R5515X)
R482 1-216-833-11 METAL CHIP 10K 5% 1/10W
R483 1-216-833-11 METAL CHIP 10K 5% 1/10W R547 1-216-809-11 METAL CHIP 100 5% 1/10W
R484 1-216-821-11 METAL CHIP 1K 5% 1/10W R548 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R549 1-216-825-11 METAL CHIP 2.2K 5% 1/10W
R491 1-216-805-11 METAL CHIP 47 5% 1/10W R550 1-216-864-11 SHORT CHIP 0 (R5515X/R5610)
(R6550)
(R5515X) R554 1-216-821-11 METAL CHIP 1K 5% 1/10W
(R5515X/R5610) R602 1-216-849-11 METAL CHIP 220K 5% 1/10W
(R5610/R6550)
R604 1-216-835-11 METAL CHIP 15K 5% 1/10W
(R5515X, R6550) R607 1-216-821-11 METAL CHIP 1K 5% 1/10W
R507 1-216-845-11 METAL CHIP 100K 5% 1/10W R608 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
(R5610) R610 1-216-809-11 METAL CHIP 100 5% 1/10W
R508 1-216-845-11 METAL CHIP 100K 5% 1/10W
(R5610) R611 1-216-809-11 METAL CHIP 100 5% 1/10W
R703 1-216-833-11 METAL CHIP 10K 5% 1/10W
(R5515X)
R512 1-216-845-11 METAL CHIP 100K 5% 1/10W R705 1-249-425-11 CARBON 4.7K 5% 1/4W
(R5610/R6550) R706 1-216-841-11 METAL CHIP 47K 5% 1/10W
R515 1-216-809-11 METAL CHIP 100 5% 1/10W R708 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R517 1-216-845-11 METAL CHIP 100K 5% 1/10W R710 1-249-425-11 CARBON 4.7K 5% 1/4W
R519 1-218-871-11 METAL CHIP 10K 0.5% 1/10W R712 1-216-837-11 METAL CHIP 22K 5% 1/10W
R520 1-218-871-11 METAL CHIP 10K 0.5% 1/10W
R521 1-216-821-11 METAL CHIP 1K 5% 1/10W < SWITCH >
R522 1-218-871-11 METAL CHIP 10K 0.5% 1/10W S103 1-786-826-11 SWITCH, TACTILE (RESET)
R523 1-216-845-11 METAL CHIP 100K 5% 1/10W S501 1-571-478-11 SWITCH, SLIDE (FREQUENCY SELECT) (R5610)
R524 1-216-845-11 METAL CHIP 100K 5% 1/10W
R525 1-216-845-11 METAL CHIP 100K 5% 1/10W < THERMISTOR (POSITIVE) >
R526 1-216-841-11 METAL CHIP 47K 5% 1/10W
TH400 1-803-350-21 THERMISTOR, POSITIVE
R527 1-216-841-11 METAL CHIP 47K 5% 1/10W
R528 1-216-833-11 METAL CHIP 10K 5% 1/10W < TUNER >
R529 1-216-845-11 METAL CHIP 100K 5% 1/10W
R530 1-216-845-11 METAL CHIP 100K 5% 1/10W TU1 A-3220-961-A TUNER UNIT (TUX-032)
R531 1-216-845-11 METAL CHIP 100K 5% 1/10W
< VIBRATOR >
R532 1-216-845-11 METAL CHIP 100K 5% 1/10W
R533 1-216-845-11 METAL CHIP 100K 5% 1/10W X50 1-813-173-11 VIBRATOR, CRYSTAL (8.664MHz) (R6550)
R534 1-216-845-11 METAL CHIP 100K 5% 1/10W X500 1-813-524-21 VIBRATOR, CERAMIC (18.432MHz)
R535 1-216-864-11 SHORT CHIP 0 X501 1-813-202-11 VIBRATOR, CRYSTAL (32.768kHz)
R536 1-216-864-11 SHORT CHIP 0 *************************************************************
53
CDX-R5515X/R5610/R6550
PRESET SENSOR
PRESET BOARD R908 1-216-827-11 METAL CHIP 3.3K 5% 1/10W
************* R909 1-216-829-11 METAL CHIP 4.7K 5% 1/10W
R910 1-218-867-11 METAL CHIP 6.8K 0.5% 1/10W
< CONNECTOR > R911 1-216-833-11 METAL CHIP 10K 5% 1/10W
R912 1-216-835-11 METAL CHIP 15K 5% 1/10W
CN905 1-785-616-11 CONNECTOR, FPC (0.5mm PITCH) 6P
R930 1-216-813-11 METAL CHIP 220 5% 1/10W
< SURGE ABSORBER > (R5515X)
R930 1-216-815-11 METAL CHIP 330 5% 1/10W
CP901 1-805-043-11 ABSORBER, CHIP SURGE (R5610/R6550)
R931 1-216-811-11 METAL CHIP 150 5% 1/10W
< SWITCH > (R5515X)
R931 1-216-813-11 METAL CHIP 220 5% 1/10W
LSW903 1-786-805-11 SWITCH, TACTILE (WITH LED) (SOURCE) (R5610/R6550)
(R5610/R6550) R932 1-216-811-11 METAL CHIP 150 5% 1/10W
LSW903 1-786-807-11 SWITCH, TACTILE (WITH LED) (SOURCE) (R5515X)
(R5515X)
LSW904 1-786-805-11 SWITCH, TACTILE (WITH LED) (MODE) R932 1-216-813-11 METAL CHIP 220 5% 1/10W
(R5610/R6550) (R5610/R6550)
LSW904 1-786-807-11 SWITCH, TACTILE (WITH LED) (MODE) R933 1-216-811-11 METAL CHIP 150 5% 1/10W
(R5515X) (R5515X)
LSW905 1-786-805-11 SWITCH, TACTILE (WITH LED) (1,GP/DISC –) R933 1-216-813-11 METAL CHIP 220 5% 1/10W
(R5610/R6550) (R5610/R6550)
R934 1-216-811-11 METAL CHIP 150 5% 1/10W
LSW905 1-786-807-11 SWITCH, TACTILE (WITH LED) (1,GP/DISC –) (R5515X)
(R5515X) R934 1-216-813-11 METAL CHIP 220 5% 1/10W
LSW906 1-786-805-11 SWITCH, TACTILE (WITH LED) (2,GP/DISC +) (R5610/R6550)
(R5610/R6550)
LSW906 1-786-807-11 SWITCH, TACTILE (WITH LED) (2,GP/DISC +) R935 1-216-811-11 METAL CHIP 150 5% 1/10W
(R5515X) (R5515X)
LSW907 1-786-805-11 SWITCH, TACTILE (WITH LED) (3/REP) R935 1-216-813-11 METAL CHIP 220 5% 1/10W
(R5610/R6550) (R5610/R6550)
LSW907 1-786-807-11 SWITCH, TACTILE (WITH LED) (3/REP) R936 1-216-811-11 METAL CHIP 150 5% 1/10W
(R5515X) (R5515X)
R936 1-216-813-11 METAL CHIP 220 5% 1/10W
LSW908 1-786-805-11 SWITCH, TACTILE (WITH LED) (4/SHUF) (R5610/R6550)
(R5610/R6550) R937 1-216-811-11 METAL CHIP 150 5% 1/10W
LSW908 1-786-807-11 SWITCH, TACTILE (WITH LED) (4/SHUF) (R5515X)
(R5515X)
LSW909 1-786-805-11 SWITCH, TACTILE (WITH LED) (5/BBE MP) R937 1-216-813-11 METAL CHIP 220 5% 1/10W
(R5610/R6550) (R5610/R6550)
LSW909 1-786-807-11 SWITCH, TACTILE (WITH LED) (5/BBE MP) R938 1-216-811-11 METAL CHIP 150 5% 1/10W
(R5515X) (R5515X)
LSW910 1-786-805-11 SWITCH, TACTILE (WITH LED) (6) R938 1-216-813-11 METAL CHIP 220 5% 1/10W
(R5610/R6550) (R5610/R6550)
R939 1-216-811-11 METAL CHIP 150 5% 1/10W
LSW910 1-786-807-11 SWITCH, TACTILE (WITH LED) (6) (R5515X) (R5515X)
LSW911 1-786-805-11 SWITCH, TACTILE (WITH LED) (AF/TA) R939 1-216-813-11 METAL CHIP 220 5% 1/10W
(R5610/R6550) (R5610/R6550)
LSW911 1-786-807-11 SWITCH, TACTILE (WITH LED) (AF/TA)
(R5515X) R940 1-216-811-11 METAL CHIP 150 5% 1/10W
LSW912 1-786-805-11 SWITCH, TACTILE (WITH LED) (SENS/BTM) (R5515X)
(R5610/R6550) R940 1-216-813-11 METAL CHIP 220 5% 1/10W
LSW912 1-786-807-11 SWITCH, TACTILE (WITH LED) (SENS/BTM) (R5610/R6550)
(R5515X) R941 1-216-811-11 METAL CHIP 150 5% 1/10W
(R5610/R6550)
LSW913 1-786-805-11 SWITCH, TACTILE (WITH LED) (PTY/LIST) R941 1-216-815-11 METAL CHIP 330 5% 1/10W
(R5610/R6550) (R5515X)
LSW913 1-786-807-11 SWITCH, TACTILE (WITH LED) (PTY/LIST) R942 1-216-811-11 METAL CHIP 150 5% 1/10W
(R5515X) *************************************************************
< RESISTOR > SENSOR BOARD

**************
R903 1-216-819-11 METAL CHIP 680 5% 1/10W
R904 1-216-821-11 METAL CHIP 1K 5% 1/10W < SWITCH >
R905 1-216-823-11 METAL CHIP 1.5K 5% 1/10W
R906 1-216-823-11 METAL CHIP 1.5K 5% 1/10W SW2 1-529-566-61 SWITCH, PUSH (1 KEY) (SELF)
R907 1-216-825-11 METAL CHIP 2.2K 5% 1/10W SW3 1-529-566-61 SWITCH, PUSH (1 KEY) (DISC IN)
*************************************************************
54
CDX-R5515X/R5610/R6550
SERVO
A-1075-784-A SERVO BOARD, COMPLETE C106 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V
**********************
< CONNECTOR >
< CAPACITOR >
CN1 1-691-380-21 CONNECTOR, FFC/FPC 16P
C4 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V CN2 1-817-275-21 CONNECTOR, BOARD TO BOARD 28P
C6 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V < JUMPER RESISTOR >
C9 1-104-609-11 ELECT CHIP 100uF 20% 4V FB2 1-216-864-11 SHORT CHIP 0
FB3 1-216-864-11 SHORT CHIP 0
C10 1-162-962-11 CERAMIC CHIP 470PF 10% 50V FB4 1-216-864-11 SHORT CHIP 0
C16 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V < IC >
C18 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V IC1 6-707-327-01 IC BA5968FP-E2
IC2 6-707-328-01 IC TC94A60MFG-301
C19 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V IC3 6-805-086-02 IC MB90487APFV-G-142-BNDE1
C20 1-164-245-11 CERAMIC CHIP 0.015uF 10% 25V IC6 6-705-364-01 IC R1114N151D-TR-FA
C22 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V < TRANSISTOR >
Q1 8-729-904-87 TRANSISTOR 2SB1197K-R
C24 1-100-567-81 CERAMIC CHIP 0.01uF 10% 25V Q2 8-729-904-87 TRANSISTOR 2SB1197K-R
C27 1-164-677-11 CERAMIC CHIP 0.033uF 10% 16V Q3 8-729-928-90 TRANSISTOR DTC114EE
C29 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V < RESISTOR >
R1 1-218-941-81 RES-CHIP 100 5% 1/16W
C32 1-162-923-11 CERAMIC CHIP 47PF 5% 50V R2 1-208-699-11 METAL CHIP 4.7K 0.5% 1/16W
C33 1-164-677-11 CERAMIC CHIP 0.033uF 10% 16V R3 1-208-912-11 METAL CHIP 11K 0.5% 1/16W
C34 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V R4 1-218-969-11 RES-CHIP 22K 5% 1/16W
R6 1-218-929-11 RES-CHIP 10 5% 1/16W
C37 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V R7 1-218-929-11 RES-CHIP 10 5% 1/16W
C38 1-162-962-11 CERAMIC CHIP 470PF 10% 50V R8 1-218-967-11 RES-CHIP 15K 5% 1/16W
C39 1-162-962-11 CERAMIC CHIP 470PF 10% 50V R9 1-218-967-11 RES-CHIP 15K 5% 1/16W
R11 1-218-965-11 RES-CHIP 10K 5% 1/16W
R19 1-218-967-11 RES-CHIP 15K 5% 1/16W
C51 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V R22 1-218-990-11 SHORT CHIP 0
C53 1-125-777-11 CERAMIC CHIP 0.1uF 10% 10V R24 1-218-962-11 RES-CHIP 5.6K 5% 1/16W
R25 1-218-990-11 SHORT CHIP 0
C59 1-112-195-11 ELECT 47uF 20% 4V R28 1-218-947-11 RES-CHIP 330 5% 1/16W
C60 1-112-195-11 ELECT 47uF 20% 4V R40 1-218-941-81 RES-CHIP 100 5% 1/16W
C61 1-126-208-21 ELECT CHIP 47uF 20% 4V R41 1-218-977-11 RES-CHIP 100K 5% 1/16W
R42 1-218-977-11 RES-CHIP 100K 5% 1/16W
C67 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V R45 1-218-989-11 RES-CHIP 1M 5% 1/16W
C72 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V R46 1-218-947-11 RES-CHIP 330 5% 1/16W
C80 1-125-837-11 CERAMIC CHIP 1uF 10% 6.3V
R47 1-218-977-11 RES-CHIP 100K 5% 1/16W
C102 1-162-962-11 CERAMIC CHIP 470PF 10% 50V R49 1-218-941-81 RES-CHIP 100 5% 1/16W
55
CDX-R5515X/R5610/R6550
SERVO
R52 1-218-945-11 RES-CHIP 220 5% 1/16W X2 1-795-561-21 VIBRATOR, CERAMIC (16.9344MHz)
R53 1-218-941-81 RES-CHIP 100 5% 1/16W *************************************************************
R54 1-218-941-81 RES-CHIP 100 5% 1/16W
R55 1-218-977-11 RES-CHIP 100K 5% 1/16W MISCELLANEOUS
R56 1-218-941-81 RES-CHIP 100 5% 1/16W ***************
R57 1-218-941-81 RES-CHIP 100 5% 1/16W 6 1-776-207-72 CORD (WITH CONNECTOR) (POWER)
R58 1-218-941-81 RES-CHIP 100 5% 1/16W (R5515X/R5610)
R59 1-218-977-11 RES-CHIP 100K 5% 1/16W 6 1-776-527-71 CORD (WITH CONNECTOR) (ISO) (POWER)
R60 1-218-977-11 RES-CHIP 100K 5% 1/16W (R6550)
R61 1-218-977-11 RES-CHIP 100K 5% 1/16W 57 1-830-258-11 CABLE, FLEXIBLE FLAT (6 CORE)
68 1-830-259-11 CABLE, FLEXIBLE FLAT (12 CORE)
R62 1-218-977-11 RES-CHIP 100K 5% 1/16W 0 153 8-820-207-12 OPTICAL PICK-UP (KSS1000E/K1RP)
R63 1-218-977-11 RES-CHIP 100K 5% 1/16W
R64 1-218-977-11 RES-CHIP 100K 5% 1/16W 154 A-1075-787-A CHASSIS (OP) SUB ASSY (including M901)
R65 1-218-941-81 RES-CHIP 100 5% 1/16W F901 1-532-877-11 FUSE (BLADE TYPE) (AUTO FUSE) 10A
R66 1-218-941-81 RES-CHIP 100 5% 1/16W M902 A-3337-638-A MOTOR ASSY, SL (SLED)
M903 A-1075-792-A MOTOR ASSY, LE (LOADING)
R67 1-218-941-81 RES-CHIP 100 5% 1/16W SW4 1-571-099-11 SWITCH (1 KEY) (LIMIT)
R68 1-218-941-81 RES-CHIP 100 5% 1/16W *************************************************************
R69 1-218-941-81 RES-CHIP 100 5% 1/16W
R70 1-218-941-81 RES-CHIP 100 5% 1/16W
R71 1-220-804-11 RES-CHIP 2.2M 5% 1/16W
R72 1-218-941-81 RES-CHIP 100 5% 1/16W

R73 1-218-973-11 RES-CHIP 47K 5% 1/16W
R74 1-218-941-81 RES-CHIP 100 5% 1/16W
R77 1-218-941-81 RES-CHIP 100 5% 1/16W
R78 1-218-941-81 RES-CHIP 100 5% 1/16W
R80 1-218-941-81 RES-CHIP 100 5% 1/16W

R81 1-218-973-11 RES-CHIP 47K 5% 1/16W
R82 1-218-973-11 RES-CHIP 47K 5% 1/16W
R83 1-218-973-11 RES-CHIP 47K 5% 1/16W
R84 1-218-953-11 RES-CHIP 1K 5% 1/16W
R86 1-218-969-11 RES-CHIP 22K 5% 1/16W

R90 1-218-941-81 RES-CHIP 100 5% 1/16W
R91 1-218-941-81 RES-CHIP 100 5% 1/16W
R100 1-220-200-81 RES-CHIP 30K 5% 1/16W
R101 1-218-971-11 RES-CHIP 33K 5% 1/16W
R112 1-218-990-11 SHORT CHIP 0

R113 1-218-990-11 SHORT CHIP 0
R116 1-218-977-11 RES-CHIP 100K 5% 1/16W
R117 1-218-977-11 RES-CHIP 100K 5% 1/16W
R118 1-218-977-11 RES-CHIP 100K 5% 1/16W
R119 1-218-977-11 RES-CHIP 100K 5% 1/16W

R120 1-218-990-11 SHORT CHIP 0
R121 1-218-990-11 SHORT CHIP 0
R122 1-218-990-11 SHORT CHIP 0
R123 1-218-990-11 SHORT CHIP 0
R125 1-218-941-81 RES-CHIP 100 5% 1/16W

R126 1-218-941-81 RES-CHIP 100 5% 1/16W
R127 1-218-941-81 RES-CHIP 100 5% 1/16W
R128 1-218-941-81 RES-CHIP 100 5% 1/16W
R131 1-216-864-11 SHORT CHIP 0
R132 1-218-962-11 RES-CHIP 5.6K 5% 1/16W
< SWITCH >
SW1 1-529-565-61 SWITCH, PUSH (1 KEY) (DOWN)
< VIBRATOR >
X1 1-813-371-21 VIBRATOR, CERAMIC (12MHz)
The components identified by Les composants identifiés par

mark 0 or dotted line with mark une marque 0 sont critiques
0 are critical for safety. pour la sécurité.
Replace only with part number Ne les remplacer que par une
56 specified. piéce portant le numéro spécifié.
CDX-R5515X/R5610/R6550
Ref. No. Part No. Description Remark

ACCESSORIES
************
1-479-077-11 REMOTE COMMANDER (RM-X151)

2-348-439-11 MANUAL, INSTRUCTION (ENGLISH,FRENCH)
(R5515X)
2-348-439-21 MANUAL, INSTRUCTION (ENGLISH,GERMAN,
FRENCH,ITALIAN,DUTCH) (R6550)
2-348-439-31 MANUAL, INSTRUCTION (ENGLISH,SPANISH,
TRADITIONAL CHINESE) (R5610)
2-348-440-11 MANUAL, INSTRUCTION, INSTALL (ENGLISH,
FRENCH) (R5515X)

GERMAN,FRENCH,ITALIAN,DUTCH)
(R6550)
SPANISH,TRADITIONAL CHINESE)
(R5610)
2-548-729-01 LID, BATTERY CASE (for RM-X151)
X-2050-189-1 CASE ASSY (for FRONT PANEL)
*************************************************************
PARTS FOR INSTALLATION AND CONNECTIONS

***************************************
301 X-3382-647-1 FRAME ASSY, FITTING

302 1-465-459-41 ADAPTOR, ANTENNA (R6550)
303 1-776-207-72 CORD (WITH CONNECTOR) (POWER)
(R5515X/R5610)
304 1-776-527-71 CORD (WITH CONNECTOR) (ISO) (POWER)
(R6550)
305 3-246-011-01 KEY (FRAME)
306 2-187-150-01 COLLAR

307 A-1082-993-A SCREW ASSY (BS4), FITTING (R5610)
308 X-3366-972-2 SCREW ASSY (EXP), FITTING (R6550)
309 2-581-692-01 SCREW, FITTING (R5610/R6550)
310 3-246-471-01 SCREW (+K 5X8 TP) (R5515X/R5610)
301 302 303
304 305 306
×2
307
308 310
309
×4
57
CDX-R5515X/R5610/R6550
MEMO
58
CDX-R5515X/R5610/R6550
US Model
Canadian Model
CDX-R5515X
SERVICE MANUAL AEP Model

UK Model
Ver. 1.1 2005.07 CDX-R6550
E Model
CDX-R5610
SUPPLEMENT-1
File this supplement with the service manual.
Subject : Change of CD mechanism.
This model provides two types of CD mechanisms.

Check the label on the chassis (T) when servicing the CD mechanism.
DISCRIMINATION
DT A s s s s s s s s
Model Name
Factory
D : MG-611TA-186//K (Refer to Service Manual)
E : MG-611TA-186//C (Refer to Supplement-1)
9-879-368-81
CDX-R5515X/R5610/R6550
EXPLODED VIEWS
NOTE:
• The mechanical parts with no reference • Color Indication of Appearance Parts The components identified by
number in the exploded views are not supplied. Example : mark 0 or dotted line with mark
• Items marked “*” are not stocked since KNOB, BALANCE (WHITE) ... (RED) 0 are critical for safety.
they are seldom required for routine service. R R Replace only with part number
Some delay should be anticipated Parts Color Cabinet’s Color specified.
when ordering these items. • Accessories are given in the last of this parts list.
• -XX and -X mean standardized parts, so Les composants identifiés par une
they may have some difference from the marque 0 sont critiques pour
original one. la sécurité.
Ne les remplacer que par une piéce
portant le numéro spécifié.
1. CD MECHANISM SECTION (1)

(MG-611TA-186//C)
not supplied
(SENSOR board)
101
not supplied
#4
not supplied
not supplied
not supplied
103
104
106
105
102
107
101 A-1088-624-A CHASSIS (T) SUB ASSY 105 2-345-767-21 SPRING (KF60), TENSION
102 A-1092-999-A SERVO BOARD, COMPLETE 106 3-253-748-11 DAMPER (S)
103 2-345-865-11 SPRING (DAMPER), COMPRESSION (BLACK) 107 3-352-758-31 SCREW (M1.7X2.5), TOOTHED LOCK
104 2-345-865-01 SPRING (DAMPER), COMPRESSION (NATURAL) #4 7-627-552-87 SCREW, PRECISION +P 1.7X2.2
2
CDX-R5515X/R5610/R6550

(MG-611TA-186//C)
155
156
157
154
(including M901)
#5
M902
161
SW4
160
159
158
153
not supplied
not supplied
152
151
151 A-1088-612-A CHASSIS (OP) COMPLETE ASSY 158 3-261-959-21 SPRING (SL), TORSION
152 3-316-938-91 SCREW (B1.4X5), TAPPING 159 3-253-736-21 SPRING (CHKG), TENSION
0 153 8-820-207-12 OPTICAL PICK-UP (KSS1000E/K1RP) 160 3-264-165-21 SCREW
154 A-1088-615-A CHASSIS (OP) SUB ASSY (including M901) 161 3-253-742-21 WHEEL (SL), WORM
155 A-1088-616-A ARM SUB ASSY, CHUCKING M902 A-1088-614-A MOTOR ASSY, SL (SLED)
156 A-1088-613-A LEVER (SL) SUB ASSY SW4 1-571-099-11 SWITCH (1 KEY) (LIMIT)
157 X-2024-784-2 LEVER (SL) ASSY #5 7-627-850-77 SCREW, PRECISION +P 1.4X1.8
3
CDX-R5515X/R5610/R6550

(MG-611TA-186//C)
201 203
202
207
211
204
209
208 210 205
207
207
M903
#4
206
201 3-262-755-11 WASHER (1.1-2.5) 208 2-186-696-21 BRACKET (LEM-N)
202 2-186-699-21 GEAR (RA1) 209 3-345-648-91 SCREW (M1.4), TOOTHED LOCK
203 A-1088-618-A ARM ASSY, ROLLER 210 A-1088-623-A GEAR (LE) ASSY
204 3-259-455-21 SPRING (RAL) 211 2-186-697-21 BEARING (LEB-N)
205 3-253-713-21 SPRING (RAR) M903 A-1088-622-A MOTOR ASSY, LE (LOADING)
206 3-259-469-21 SPRING (LE), LEAF #4 7-627-552-87 SCREW, PRECISION +P 1.7X2.2

207 2-134-636-51 SCREW (M1.7X2.5)
4
CDX-R5515X/R5610/R6550

(MG-611TA-186//C)
254
252
255
252
258
256
251 253
257
251 2-186-700-21 GEAR (CHK1) 255 3-899-829-01 WASHER (SLIT)
252 3-344-223-01 WASHER 256 2-590-545-21 GEAR (LE2-M)
253 3-259-470-22 GEAR (LE1) 257 A-1088-620-A CHASSIS (M) BLOCK ASSY
254 3-253-755-21 LEVER (D) 258 3-262-755-11 WASHER (1.1-2.5)
5
CDX-R5515X/R5610/R6550
REVISION HISTORY
Clicking the version allows you to jump to the revised page.

Also, clicking the version at the upper on the revised page allows you to jump to the next revised page.
Ver. Date Description of Revision

1.0 2004.12 New
1.1 2005.07 Change of CD mechanism. (Supplement-1) (ECN-ECB00626)

CDXR6550 1706729786

Uploaded by

Copyright:

Available Formats

CDXR6550 1706729786

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

CDXR6550 1706729786

Uploaded by

Copyright:

Available Formats

CDX-R5515X/R5610/R6550

SERVICE MANUAL US Model

• The tuner and CD sections have no adjustments.

FM/AM COMPACT DISC PLAYER

9-879-368-02 Sony Corporation

US and foreign patents licensed from Dolby Laboratories.

Design and specifications are subject to change without

NOTES ON HANDLING THE OPTICAL PICK-UP BLOCK

NOTES ON LASER DIODE EMISSION CHECK SAFETY-RELATED COMPONENT WARNING!!

• CD Playback: z UNLEADED SOLDER

EXTENSION CABLE AND SERVICE POSITION

MAIN BOARD J-2502-076-1

5. ELECTRICAL PARTS LIST ......................................... 48

Location of controls and basic operations

wa qs B ATT (attenuate) button “BBEMP-ON” during playback on this unit.

Location of controls and basic operations

Location of controls and basic operations

Radio: *3 When an MP3/ATRAC CD is played and a changer

Connection example (2)

AUDIO OUT REAR

Connection example (2)

Exemple de raccordement (2)

Esempio di collegamento (2)

Supplied with XA-C30 XA-C30

from car antenna

2-1. SUB PANEL (LCD) ASSY

2-2. CD MECHANISM BLOCK

2-5. ROLLER ARM ASSY

2-6. CHASSIS (OP) ASSY 2-9. LE MOTOR ASSY (M903)

2-8. SL MOTOR ASSY (M902) 2-7. OPTICAL PICK-UP

FRONT PANEL COMPLETE ASSY

2-11. FRONT BACK PANEL (LCD)

2-12. KEY BOARD

2-13. DISPLAY SECTION

2-14. SPRING (M)

2-15. SPRING (S)

Note : Follow the disassembly procedure in the numerical order given.

2-1. SUB PANEL (LCD) ASSY

4 sub panel (LCD) assy

2-2. CD MECHANISM BLOCK

2-3. MAIN BOARD

2-4. CHASSIS (T) SUB ASSY

6 chassis (T) sub assy

2-5. ROLLER ARM ASSY

5 roller arm assy

2-6. CHASSIS (OP) ASSY

0 coil spring (damper)

5 gear (LE1) 9 two coil springs (damper)

3 tension coil spring (KF60)

2-7. OPTICAL PICK-UP

2 chucking arm sub assy

1 tension coil spring (CHKG)

2-8. SL MOTOR ASSY (M902)

2 SL motor assy (M902)

2-9. LE MOTOR ASSY (M903)

0 gear (LE) assy 8 screw

1 Remove the soldering.

2-10. SERVO BOARD

1 Remove the eight solderings. 6 SERVO board