BATCH TEST CERTIFICATE

Date :23/06/2023

Product : ZP- 4B

Batch No :23F1019

Mfd. in : JUNE 2023

We hereby certify that when tested at time of manufacture, the above material:

1. Meets the requirements of and has been tested for sulfur and halogens according to:

A. ASME Boiler and Pressure Vessel Code, 2004, 2007, 2010, 2013, 2015, 2017,2019 and 2021 Edition, Section
V, Nondestructive
Examination, including 2005, 2006, 2008, 2009b, and 2011a Addenda, Article 6 Paragraph T-641
and Article 24 as applicable.

B. ASME Boiler and Pressure Vessel Code, 1995, 1998 and 2001 Edition, Section V Nondestructive
Examination, including 1999, 2000, 2002 and 2003 Addenda, Article 6 Paragraph T-640 and Article
24 as applicable.

C. ASME Boiler and Pressure Vessel Code, 1986, 1989and 1992 Edition, Section V, Nondestructive
Examination, Article 6 including 1992 Addenda, Paragraph T-625, 1993 Addenda Paragraph T-640
and Article 24 as applicable.

D. ASTM E-165-92, ASTME-165-94,ASTM E-165-95, ASTM E-165-02,ASTME-165-09,ASTM E-165/E-165M-12,

ASTM-165/E-165M-18, Paragraph 7.1.

The following test results were obtained:

1. Sulfur : less than 0.0025 ppm

2. CL+F : less than 0.0025 ppm

3. Cleaner residue (see note 3) : NA g/100g

2. We further certify that this material does not contain mercury as a basic element and no mercury bearing
equipment was used in its manufacture.

Notes:
1. Batch numbers are printed on the labels of bulk containers.
2. Most specifications require test results stated in percent but some require parts per million (ppm). To convert “percent” figures to “parts per million” move the
decimal four places to the right.
3.The above certification gives the results obtained at the time of manufacture. Age and use may alter the properties of any material.
Page 1 of 3 Form No: F/QC/160/07 Rev: 09/2021

We further certify that the product meets the requirement of AMS 2644H and is approved by the U.S. Air Force and listed on QPL-
AMS-2644.

When tested according to paragraph 4.3.2., Sampling Plan A, the following results were obtained:

4.2.2.1. Penetrant Tests:

Flash Point (PMCC), 3.3.3 _________NA___˚F

Viscosity, 3.3.4( cs. Nominal) NA

Fluorescent Brightness, 3.3.8.3.2.(FP-4PE Standard) _____ ___NA___%

Water Tolerance (Method A, B, C, D), 3.3.8.5 _________NA __%

Removability, 3.3.8.6 ______ NA __

4.2.2.1 Emulsifier Tests:

Flash Point (PMCC), 3.3.3 ________NA_________˚F

Viscosity, 3.3.4( cs. Nominal) ________NA_________cs@100˚F

Water Content (Method B only), 3.3.9.6 ________NA________%

4.2.2.3. Developer Tests:

Developer Fluorescence, 3.3.10.2 _________PASS____

Developer Removability, 3.3.10.4 _________PASS____

Redispersibility, 3.3.10.5 _________NA_______

3.3.11.4 Remover Tests:

Penetrant Removal, 4.4.11.2 _________NA________

We further certify that this material meets the requirements of ASTM E 1417, Paragraph 5.1.

Quality Assurance
 Page 2 of 3

Form No: F/QC/160/07 Rev: 09/2021

Date: 11/11/2022
VENDOR’S REPORT - TEST RESULTS
Please forward in duplicate to:
REPORTS, MATERIALS CONTROL LABORATORY
PRATT & WHITNEY
(Plant to which material is shipped)

This is to certify that Paragraph Number(s)__________________________________ apply to the shipment below: (insert at least one of the first 4,
plus 5 if applicable).
1. (Applicable to all raw material, to parts made from raw material furnished or purchased by vendor, or to assemblies of which some or all components are made from
raw material furnished or purchased by vendor.) Material, parts, or components of assemblies have been inspected and accepted to the specifications involved, and
results of tests required by Pratt & Whitney Aircraft are shown herein.
2. (Applicable to parts or assembly components made from raw material furnished by Pratt & Whitney Aircraft and not chemically or metallurgically treated by vendor so
as to change surface or internal condition significantly.) Parts or assemblies have been machined or formed from material furnished by Pratt & Whitney Aircraft, to make
these parts or components of assemblies.
3. (Applicable to parts or assembly components made from raw material furnished by Pratt & Whitney Aircraft and chemically or metallurgically treated by vendor so as to
change surface or internal condition significantly.) Parts of components of assemblies have been made from raw material furnished by Pratt & Whitey Aircraft to make
these parts or components of assemblies. Parts, components of assemblies have been inspected and accepted to the specifications involved, and results of tests
required by Pratt & Whitney Aircraft are as show herein.
4. (Applicable to repaired or reworked raw material, parts or assemblies.) The raw materials, parts or assemblies have been reworked or repaired in accordance with
Pratt & Whitney Aircraft Instructions, and are the same material, parts or assemblies returned for such reworking or repair, except for replacement of assembly
components, in which case paragraphs 1 and 5 are also applicable.
5. (Applicable to all assemblies, and to parts when specifically authorized by purchaser.) Results of all chemical and physical tests not shown below, as well as all other
evidence which shows acceptability of raw materials and assembly components, are on file and available for inspection at any reasonable time.

PART OR ASS’Y NO.(Size if no Part No.) CHG.LTR SUF.No SPECIFICATIONS,AS ORDERED

PMC 4356AA 4 PWA 300 Rev.BP
QUANTITY DATE SHIPPED LOCATION OF PWA PLANT PACK SLIP NO P O No.
TO SHIPPED TO

HEAT ,LOT,CODE OR BATCH NO. RAW MATERIAL VENDOR TYPE – COMPOUND OR CASTING PWA HEAT CODES (If required)
Batch No. 22L1013 Zyglo Developer ZP-4B

If materials, parts or assemblies do not entirely confirm to specification requirements, the deviation and authority for furnishing such materials are indicated below:

RESULTS OF TESTS (Use reverse side if necessary)

PMC LIMITS PMC LIMITS

PHYSICAL PROPERTIES ACCEPTED VALUES
(MINIMUM) (MAXIMUM)
Flash Point NA 200 deg F --
Appearance PASS -- White fluffy powder
Water Content NA -- --
Fluorescent Brightness NA 90% 110%
Separation of Constituents-Homogenous PASS No Yellow , Red , Green fluorescence

CHEMICAL PROPERTIES ACCEPTED VALUES PMC LIMITS (MINIMUM) PMC LIMITS (MAXIMUM)
Fluoride Content < 5 ppm -- =< 50 ppm
Chloride Content < 50 ppm -- =< 1000 ppm
Sulfur Content < 0.0025 % -- =< 0.1000%
Sodium Content < 0.0025 % -- =< 0.1000%
Magnaflux certifies that Zyglo Developer ZP-4B meets the requirements of PMC 4356 AA

VENDOR NAME ITW India Private Limited-Magnaflux BY (Authorizing Agent)

VENDOR ADDRESS IDA, Phase 2 , Pashammylaram Bhaskar V ,Quality Assurance

Hyderabad

Page 3 of 3 Form No: F/QC/160/07 Rev: 09/2021