4

University of Strathclyde
Thesis in partial fulfilment for the degree of Master

of Science in Energy Systems and the Environment
By George Gartzounis ,
2001-2003,
Departmen t of Mechan ical Engineering,

Energy Systems Research Unit.
“Sustainable Engineering:
Renewable Technology Integration
as an Implementation Measure for
the Dissemination of Energy
Autonomous Communities in the
form of Eco-Villages – Tweed
Valley Project; Scotland”
Decla ration o f Author’s Ri ght

“The copyright of this thesis belongs to the author under the terms of the United Kingdom
Copyright Acts as qualified by University of Strathclyde Regulation 3.49. Due
acknowledgement must always be made of the use of any material contained in, or derived
from, this thesis.”
2
Acknowledge ments
I dedicate this thesis to the Engineering Community that has offered so
much to the humanity since the dawn of civilisation and to my father who
wished to see me being successful in the Engineering discipline since I could
never cope with Medicine. When I started this project I could never expect
that I would learn so much about the greatness and value of Renewable
Technologies and the efforts made for their integration into the mainstream
of today’s Energy Schemes. I am happy that I belong to a family of people
that they concern and philosophise critically about the future of the planet
and I hope that this study will enable others to expand the potential of green
technologies in the future. I would sincerely like to thank anyone who
contributed to the completion of this study. Among the people that helped
me within the department of ESRU were Dr Andy Grant, Dr Paul Strachan
and Mr Cameron M. Johnstone to who I express my deeply gratification
since a valuable part of the project would not have been completed without
their elucidations and effort. To my supervisor Dr Andy Grant I own a great
thank for his guidance and patience upon the delivery of this project. My
personal efforts were reinforced by the constant concern of a number of
people amongst who I distinguish my mother (G. Helen), my sister (G.
Sapfo), my friends (B. Sotiris and D. George.) and finally all of my
colleagues and fellow students (especially Mr B. Colin and Mr. C. Currie). I
would also like to thank all the people of Innerleithen for their hospitality
upon our visit there for the preliminary inspection of the Thornylee Forest
where the Eco-Village is going to be situated.
3
Contents
Declaration of Author’s Right, 2
Acknowledgments, 3
Synopsis, 10
Chapter 1-Introduction, 12
1.1 Civilisation and Environment- A Brief Historical Review, 12
1.1.2 Hunter-Gatherers, 13
1.1.3 Agrarian Societies, 13
1.1.4 Transformation Society, 15
1.1.4.1 The Turning Point- Industrial Revolution, 15
1.2 Environmental Crisis of the 21st Century, 16
1.2.1 Anthropogenic Climate Change, 17
1.2.2 Depletion of Stratospheric Ozone , 18
1.2.3 Loss of Biodiversity, 18
1.2.4 Other Problems and Future Threats, 19
1.3 Sustainability, Ecology and Engineering, 19
1.3.1 The Principle of Environmental Health and Engineering, 22
1.3.2 The Dark Side of the Energy Industry, 23
1.4 A New Spawn, 25
1.5 Autonomo us Energy Rendition and Renewable Energy
Integration, 26
Chapter 2-Literature Review , 30

2.1 A Brave Ne w World, 30
2.1.1 Organizational and Design Principles, 31
2.1.2 The Secrets for Green Practices, 32
2.1.2.1 Permaculture, 33
2.1.2.2 Co-Housing , 34
2.1.2.3 Ecological and Sustainable Building Design, 35
2.1.3 The Vision of the Tweed Valley Eco-Village, 36
2.2 Let There Be Power, 40
2.2.1 Photovoltaic Systems, 41
2.2.1.1 PV Technology, 42
2.2.1.2 Balance of System (BOS), 44
2.2.1.3 PV Applications, 45
2.2.2 Wind Turbines, 46
4
2.2.2.1 WT Technology, 47
2.2.2.2 Operation as a Function of Wind Speed, 49
2.2.2.3 Efficiency Reduction, 51
2.2.2.4 Applications, 52
2.2.3 Hydrogen Fuel Technologies, 53
2.2.3.1 Hydrogen Manufacturing, Electrolyser, 54
2.2.3.2 Hydrogen Utilisation, Fuel Cells, 56
2.2.3.2.1 Generic FC Technology, 56
2.2.3.2.2 Fuel Cell Stacking, 60
2.2.3.2.3 Fuel Cell P lant Description, 61
2.2.3.2.4 Applications, 62
2.2.3.3. Hydrogen Storage, High Pressure Storage Tanks, 63
Chapter 3-Methodology, 67
3.1 Selection of Climatic Profile, 67
3.1.1 Data Acquisition, 67
3.1.2 Interpretation, 70
3.1.3 Validation, 74
3.1.4 Evaluation, 77
3.1.5 Formation, 81
3.1.5.1 Final Selection, 84
3.2 Selection of Power Plant, 85
3.2.1 Technical Orientation for SES Modules, 85
3.2.1.1 Electrolyser, 85
3.2.1.2 Fuel Cell, 87
3.2.1.3 Low Pressure Storage Tank, 88
3.2.2 Numerical Guidelines for SES Modules, 90
3.2.2.1 Critical Fuel Consumption for the FC, 91
3.2.2.2. Critical Number of Storage Tanks and Critical Number of Charging
D a ys, 9 4
3.3 Rudimentary Sim ulations, 96
3.3.1 MERIT- A Brief Analysis, 96
3.3.2. Scenarios Design, 103
3.3.2.1 Scenario 1, 103
3.3.2.2. Scenario 2,110
3.3.2.2.1 Fuel Cell Operating Modes, 110
3.3.2.2.2 “Demand Profile Designer” and “Specify Demand” Numerical
Configurations, 114
Chapter 4-Discussion, 118

4.1 Climatic Analysis, 118
4.1.1 Evaluation Process Remarks, 118
5
4.1.1.1 Radiation Problems, 119
4.1.1.2 Wind Speed Problems, 120
4.1.2 Formation Process Commentaries, 125
4.2 Scenarios- Results Analysis, 125
4.2.1 Software Elucidations, 125
4.2.2 Scenarios Design- Result Analysis, 126
4.2.2.1 Scenario 1, 127
4.2.2.1.1 Preliminary Phase for Scenario 1, 127
4.2.2.1.2 Main Phase for Scenario 1, 134
4.2.2.2 Scenario 2, 138
Chapter 5-Conclusions, 145

5.1 Aims A ttestation, 145
5.1.1 Aim-I, 145
5.1.2 Aim-II, 146
5.1.3 Aim III, 147
5.2 Objective Attestation, 149
5.2.1 Objective I, 149
Chapter 6-Limitations and Future Research, 153

6.1 Climatic Limitations, 153
6.1 Technical Limitations, 153
Referen ces, 156
Appendix A, 160
6
List of Figures
Figure 2.1/Eco-Village developments in Scotland, 37
Figure 2.2/Thornylee Forest and surroundings, 38
Figure 2.3/ South Facing slope, 39
Figure 2.4/ Top of the Thornylee Hill, 39
Figure 2.5/ Natural Reservoir, 39
Figure 2.6/ PV system components, 41
Figure 2.7/ The Sun’s path as a design factor for correct sizing, sitting and positioning
the PV, 42
Figure 2.8/ Roof Area (sfeet2) as a function of PV capacity, 43
Figure 2.9/ Three type of turbines that are commercially utilised, 48
Figure 2.10/ Typical power curves and areas of operation of a stall limited (dashed line)
and pitch controlled (solid line) wind turbine, 49
Figure 2.11/ Rotor speed control principle for wind speeds below nominal, 50
Figure 2.12/ Rotor speed controller characteristics: generated power derived from actual
value of rotor speed, 51
Figure 2.13/ Rotor speed control principle for wind speeds above nominal, 51
Figure 2.14/Renewable technologies are the most sustainable and clean method to
produce hydrogen, 54
Figure 2.15/ Typical Electrolysis Cell, 55
Figure 2.16/ How a FC works, 57
Figure 2.17/ Typical PEMFC schematic, 60
Figure 2.18/ Expanded View of a Basic Fuel Cell Repeated Unit in a Fuel Cell Stack, 61
Figure 2.19/ Fuel Cell Power Plant Major Processes, 62
Figure 3.1/ Area around Thornylee Forest, 68
Figure 3.2/ Observation Stations for ECN Database, 69
Figure 3.3/ UK Counties, 75
Figure 3.4/ 11 Stations from C (Thornylee Forest), 79
Figure 3.5/ Geographical Similarities of the areas of the two stations (Eskdalemuir and
Drumalbin Saws), 80
Figure 3.6/ Annual mean wind speed for UK, 81
Figure 3.7/ Main Program Window, 96
Figure 3.8/ Analysis Parameter Window, 97
Figure 3.9/ CreateClimate.exe, 98
Figure 3.10/ Demand Definition Window, 98
Figure 3.11/ Profile Designer, 99
Figure 3.12/ Supply System Definition, 100
Figure 3.13/ Generation Type Definition, 100
Figure 3.14/ Auxiliary Definition Window, 101
Figure 3.15/ Match and Dispatch, 102
Figure 3.16/ Criteria Definition, 103
Figure 4.1a/ Dry Bulb Temperature comparative chart for 1994, 122
Figure 4.1b/ Dry Bulb Temperature comparative chart for 1997, 122
Figure 4.2a/ Visibility comparative chart for 1994, 123
Figure 4.2b/ Visibility comparative chart for 1997, 123
Figure 4.3a/ Wind Speed comparative chart for 1994, 124
Figure 4.3b/ Wind Speed comparative chart for 1997, 124
Figure 4.4/ Power curves for the Demand and Supply of Attempt 1, 128
Figure 4.5/ Power curves for the Demand and Supply of Attempt 2, 128
Figure 4.6/ Power curves for the Demand and Supply for Attempt 3, 130
7
List of Tables
Table 1.1/ Annual per capita use of energy and material in different regimes, 13
Table 1.2/ Ecosystem services and functions, 22
Table 2.1/ Range of Power Outputs for WT installations, 53
Table 2.2/ Summary of Major Differences of the Fuel Cell Types, 59
Table 3.1/ File Formats of the BADC database, 71
Table 3.2 /Sorting Parameters, 71
Table 3.3/ Explanation of ID Type, 72
Table 3.4/ File Formats explanation, 73
Table 3.5 / Selected Stations for Delimitation Plan-A., 76
Table 3.6/ Validity check for the 13 Domains, 77
Table 3.7/ Stations Evaluation, 78
Table 3.8/ 3 steps of CEACP, 80
Table 3.9/ Completeness in data for the two Domains, 83
Table 3.10/ Modifications in Data nature, 83
Table 3.11/ PEM Fuel Cell Characteristics, 88
Table 3.12/ Conversions for Volume flow units, 93
Table 3.13/ Technical Characteristics for LMW-10KW turbine, 104
Table 3.14a/ Match Results for Preliminary Phase -Scenario 1, PP, 105
Table 3.14b/ Analytical Record of MERIT Selection Parameters for ReST –Scenario 1,
PP, 107
Table 3.15a/ Match Results for Main Phase -Scenario 1, MP, 108
MP, 109
Table 3.16a/ Operating Modes for the Seasonal Profile- 1 Year, 112
Table 3.16b/Corresponding Seasonal Energy Demand for Electrolyser (kWh), 112
3
Table 3.16c/ Corresponding Seasonal Hydrogen Demand for Electrolyser (Nm / h ),
113
Table 3.17/ Parameters for “Demand Profile Designer”, 114
Table 3.18a/ Match Results for Scenario 2, 115
Table 4.1/ Central Guidance Panel, 127
Table 4.2/ Technical Specifications for the PV modules, 130
Table 1-Appendix A/ Record of the stations reviewed for the Peeblesshire County , 161
8
Table 2-Appendix A/ Record of the stations reviewed at the neighbouring Counties of
Peeblesshire, 162
Table 3-Appendix A/ Local meteorological measurements for Bowhill and Eskdalemuir
areas (1994), 163
Table 4-Appendix A/ Local meteorological measurements for Bowhill and Eskdalemuir
areas (1997), 164
Abbreviations
EV Eco-Village
BOS Balance-of-System
AC Alternative Current
CoSiMReTsI Computer Simulation Methods for
Renewable Technologies Integration
DC Direct Current
D-SM Demand-Supply Matching
GEN Global Eco -Village Network
PV Photovoltaic
ReST Renewable Supply Technologies
FC Fuel Cell
PWD Principal Weather Database
QPA Qualitative Parametrical Potential
CEACP Consecutive Elimination Assessment and Comparison Plan
PES Primary Energy Source
SES Secondary Energy Source
MP Main Phase for Scenario 1
PP Preliminary Phase for Scenario 1
OM Operation Modes
OCR Operational Capacity Range for Fuel Cell
CC Capacity Cushion for the Fuel Cell
BB Batery Bank
CFC Critical Fuel Consumption
CNST Critical Number of Storage Tanks
CNCD Critical Number of Charging Days
BC Boundary Conditions
CHP Combined Heat and Power
CGP Central Guidance Panel
FR Fuel Regulator
SN Sorting Numbers
ECA Environmetal Change Network
BADC British Atmospheric Data Centre
BWEA British Wind Energy Assossiation
PEMFC Polymer Elect rolyte Membrane Fuel Cell
ESRU Energy Systems Research Unit
OS Operating System
9
Synopsis
With the dawn of the 21st century many engineering councils, institutions
and organizations around the world are found to prepare and develop their
country’s infrastructure according to the green directions as dictated by the
notion of Sustainable Development. As in every inbound trend that seeks
establishment into the mainstream of today’s development the engineering
practice requires the testing of this trend in a miniature-like specialised
applications to examine its behaviour and plan ahead for its dissemination in
the most efficient and economic way. The Eco-Village movement is an
idea of a small community of people leaving together in a selected area of
their choice, which embraces green and sustainable practices under which
their lives are experiencing the benefits of modern technology comforts and
the pleasure of habituate close to the nature. This microcosm is a hestia of
sustainable development applied in reality and not in papers and books. In
most of the occasions these villages require an autonomous operation
including methods of food, water and energy production for the
community’s needs. In principle this condition is very difficult to establish
but it is not impossible. The issue addressed by this project is relating to the
technological aspects of the Tweed Valley Eco-Village project (Scotland)
and more specifically to the provision of Energy for electrical and heating
purposes to an autonomous and sustainable extent for that community.
Obstacles like sizing, integrity of supply, and efficiency are all examined
with the help of a computer program, namely MERIT ©, to see if it is
viable for this project to use a renewable energy scheme for supporting its
existence using Wind Turbine, Photovoltaic and a Fuel Cell Plant
modules. There were two scenarios that studied different aspects of the
autonomous condition. Scenario 1 was targeted to examine Electrical
Energy absorption by the Eco-Village as that would be produced by
Photovoltaic and Wind Turbine Units whereas Scenario 2 was broader in
studying Electrical and Thermal Energy loads ingestion provided by a Fuel
Cell Plant which was designed to operate in realistic modes to cover the
energy demands of the village according to seasonal fluctuations. The use
of MERIT was the administrative and planning tool needed for a sound
evaluation of the experiments conducted within the computerised study
interface. The experiments were case studies that were intended to simulate
the renewable energy supply technologies behaviour (primary source of
electrical energy) under the weather profile for the area of study. The
profile itself was attempted to be as homogeneous as possible to the
Thornylee Forest weather identity with data arising from stations around
that location and a methodology was devised to overcome availability and
reliability problems.
10
11
Chapter 1-Introduction
The first chapter will look at the civilisation throughout time, from ancient times to synchronous eras, in an
attempt to identify any changes in the sensitive relationship involving evolution, engineering and environmental
impacts. Modern environmental problems will be addressed briefly to probe the creation of the Eco-Village notion.
The meaning of sustainable principles in engineering will also be addressed to conclude with the role of engineering
in supporting the design of Autonomous communities reflecting preclusively the Energy sector of such a task.
1.1 Civilisation and Environment-

A Brief Historical Review
The evolutionary process can describe much of man’s development. Quite
simply, those humans which were able to adapt to new environments and
had the most resources available to them, were most likely to survive, and
were therefore most likely to reproduce.
Mankind evolved at different rates across the globe, with some
settlements evolving faster than others. The wake of evolution drifted and
shaped not only the societies themselves but accordingly the more sensitive
relationship between the renditions of human acts with the place of living
i.e. the environment. Where those rates met ( at least for today’s
industrialised nations) was at the critical point of industrial revolution
transitional time span, the latter being the saddle point between an old
“benign” epoch (management of flows) and a new one of more “turbulent”
characteristics (consumption of stocks) –our epoch! The following picture
of human evolution is therefore only an insight into the general history of
mankind
Ever since humanity capacitated a social-metabolic regime Definition
thousands of years ago the crucial relationship between actions of
progression and environment was undermined. The degree of this
undermining varied over the years but throughout the timeline of evolution
it was always constant with intense accelerating rates in the last two
centuries of this millennium (See Table 1.1). The three groups of social-
metabolic regimes i.e. Hunter-Gatherers, Agrarian Societies and
Transformation Societies range from 100,000 years to today, all with
different characters and modes of dominance and control of the
surroundings.
Definition “ A stable form in which the material and energetic exchange processes between human societies and their physical environment are
organised”- Reference: LE -1
12
Table 1.1/ Annual per capita use of energy and material in different
regimes Reference: LE-2 and LE-3
Energy Material
Basic Metabolism 3,5 GJ 1-2 t
Hunter-Gatherers 10-20 GJ 2-3 t
(Factor 3-5)
Agrarian Societies 60-80 GJ 4-5 t
(Factor 20)
Transformation 250 GJ 20-22 t
(Factor 100)
1.1.2 Hunter-Gatherers
The first group, the Hunter-Gatherer societies, in terms of exploitation, are
treating the environment in a benign way. They are social-metabolically
based on an uncontrolled use of solar energy flows. Palaeolithic hunter-
gatherer societies tap more or less passively existing solar energy flows
without much trying to control these flows actively. They skim off free
energy available in their habitat but do not take systematic measures to
influence the availability or the amount of these energy flows. This epoch in
world history ended about 10,000 years ago in which no major effects on
the biosphere occurred save the use of fire to deforestation as part of their
hunting strategy- 60,000 years before present there is probable evidence of
fire used deliberately to clear forests in the Kalambo Falls site in Tanzania
Reference: LE-4
. This fire use for hunting purposes is the first indication of
ecological changes. Big game hunters thus artificially created the steppe
landscapes (by burning savannahs) on which their prey could pasture and
insofar a first incidence of a (indirect and unintended) control of the
physical environment can be observed.
1.1.3 Agrarian Societies

The second group, the Agrarian Societies, are social-metabolically based on
a controlled use of solar energy flows. This epoch began about 10’000 years
ago and ended about 200 years ago. The larger agrarian era can be divided
into the period of simple peasant societies and the period of complex
agrarian civilisations, the latter beginning about 5’000 years ago. Like hunter-
gatherer societies agrarian societies tap natural solar energy flows, but unlike
them their basic strategy aims at controlling these flows. They developed
two strategies to achieve this goal:
• Biotechnology. Energy radiating from the sun is primarily caught and

chemically fixed by plant photosynthesis, and then it is secondarily
converted by animals and finally processed by humans.
13
• Mechanical devices. Here solar energy flows available in the
biosphere as wind or running water are mechanically converted. The
total amount of these energy flows can not be influenced, but people
can increase the efficiency of energy conversion, albeit no great
breakthrough can be expected. Technological progress is slowly
pushing at elastic limits.
Energy use in agrarian societies has a general structure which can be

reconstructed as a technically modified solar energy system. Its main
characteristics are dependence on an energy flow, low energy density and
the limited possibilities of converting one energy form into another. Thus
particular energy forms like heat, movement, light or food appeared as
qualities, not as aspects of one energy flow. Material is mobilised by the use
of energy so that in the last instance the social-metabolic material flow is
limited by the available amount of energy. The sharp energetic restrictions
set by the agrarian regime thus had a limiting effect on material processes.
Industrial material like metals, salt and other chemicals provided specific
resource and pollution problems, above all in settlements. Here we find the
classical forerunners of actual “environmental destruction”, originating by
uncontrolled mining and diffusion of substances into the biosphere, which
causes unintended side-effects.
BC-1200 Reference: IS-1

• Air pollution was common in large towns long before the industrial
revolution. The pollution came from dust, wood smoke, tanneries,
animal manure and other things.
• Water pollution was less severe in some civilizations. Israeli and
Hindu cities tended to have less water pollution due to strict religious
codes about cleanliness. On the other hand, ancient Rome was
notorious for sewage-filled streets.
• Timbering stripped the forests of Babylon, Greece, Phoenicia
(Lebanon) and Italy with the rise of civilization. The wood energy
crisis led Greeks to use passive solar energy by orienting their cities
and houses toward the sun. Romans made some use of solar energy
but imported wood for timber and fuel from as far away as the Black
Sea. Both Greeks and Romans kept sacred groves of trees from being
timbered.
• Soil conservation was not widely practiced in the Mediterranean, but
cultures in China, India and Peru understood the long term impact of
soil erosion and tried to prevent it.
• Lead poisoning was common among upper class Romans who used
lead-sweetened wine and grape pulp sweetened with "sugar of lead"
as a condiment.
14
1200-1750 (Middle Ages and Renaissance) Reference: IS-1
• Timbering in the forests of England, France and Germany leaves
large tracts totally denuded by around 1550 in England and the 1600s
in Europe.
• Soil conservation was not widely practiced in the Mediterranean, but
cultures in China, India and Peru understood the long term impact of
soil erosion and used terracing, crop rotation and natural fertilizer to
prevent it.
1750-1830 (Enlightenment) Reference: IS-1

• New technologies create new pollution. Town gas from coal drips tar
into the rivers. Vulcanized rubber plants discharge noxious chemicals
directly into the streams. Coal smoke chokes the air in big cities.
Chemical factories operate without thought to people downwind.
1.1.4 Transformation Society

The last group, the transformation society which began about 250 years ago
is social-metabolically based on the use of fossil energy stocks. This society
has not yet developed a stable structure but is involved in a process of
accelerating transformation. The energetic foundation of the transformation
is the switch to the use of fossil energy carriers: coal, mineral oil and mineral
gas. This has two major implications: Very large stocks became available
within short periods of time, and the mobilisation of material was fed by
comparatively cheap and abundant energy supplies. Thus the newly formed
social regime soon will transgress the physical boundaries of the agrarian
solar energy system. The new energy regime moved far from the sustainable
scope of the older regime and reached dimensions which were
incomprehensible in the context of an agrarian society. It is self-evident that
this is the physical basis of an unsustainable economic and ecological
regime. As an immediate consequence the availability of large energy stocks
allowed mobilising material in similar dimensions. Accordingly exponential
growth of metal production over 200 years is observed, fed exclusively by
fossil energy, and no surprisingly the emergence of the first pollution
problems are a fact – a mere backside of this process: they provide the sink
aspect of material mobilisation Reference: LE-5.
1.1.4.1 The Turning Point- Industrial Revolution

The transformation society was the integration of knowledge and
experimentation primarily on the fields of mechanics, thermodynamics,
chemistry, physics, materials, and manufacturing- a continuation of a
brilliant scientific past as configured through the previous two stages of
evolution. What we call today industrial revolution was then, to the matured
15
agrarian society, the triggering mechanism for a metamorphosis to the next
social regime.
The Industrial Revolution began in the late 18th and early 19th
centuries in Britain, before spreading around the world, and is synonymous
to the ideas of increased productivity and over-consumption. Literally that
occurred with James Watt’s interest in the efficiency of the newcomer steam
engine in 1765, an interest that grew from his work as a scientific-instrument
maker and that led to his development of the separate condenser that made
the steam engine an effective industrial power source. As in a chain reaction
this invention set the trends for rapid progress and development. Coal, oil
and gas (fossil fuels) offered levels of energy production previously
undreamed of, leading to shifts towards factory-based systems and the mass
production of goods such as cotton. Fossil fuels, principally coal at the
beginning of the Industrial Revolution, were primarily used to generate
steam power and electricity, but their applications were vast, with many
industries becoming automated, hence increasing their output.
Amongst the technological traits- technological changes, of this
revolution (socioeconomic and social are out of the scope of this text) some
distinctive ones link directly to the large environmental impacts that were to
follow in the years to come. To start we have the use of new basic materials,
chiefly iron and steel and we mentioned above the use of new energy
sources, including both fuels and motive power, such as coal, the steam
engine, electricity, petroleum, and the internal-combustion engine. The
burning of fossil fuels led to a massive increase in urban air pollution
although most people felt that such a disadvantage was not significant in the
context of their new found prosperity. In addition to urban air pollution
however, other impacts of industrialisation were felt like the drastic changes
to land use with the construction of new buildings, including factories and
houses for employees, and transport facilities, including new roads and rail
tracks. Areas of countryside were destroyed and replaced by industrial
developments. In order to make best use of the remaining land, agricultural
machinery was modernised to make the production of food more efficient.
Finally there were important developments in transportation and
communication, including the steam locomotive, steamship, automobile,
airplane, telegraph, and radio. Water could not escape from the general
situation with rivers and lakes being the direct receivers of the pollution
wave.
1.2 Environmental Crisis of the 21st Century

The industrial revolution (which began in the late 1700s) and ongoing
advances in science and technology during the last two hundred years have
had profound effects for humanity and earth. Life in an industrial society
offers many of us incredible opportunities, including greatly increased life
spans and a higher standard of living. An industrial society also uses more
16
resources and has greater impacts on the environment than an agrarian
society. Initially these new chemical, physical, and biological impacts
remained local or regional in scale. Only in the 1940s, after World War II,
did the environmental ramifications of human activities begin to affect the
functioning of major earth systems. The U.S. alone has consumed more
mineral resources in the last few decades than all of civilization did before
that Reference: IS-2. Certain global environmental problems that arose in the
closing decades of the twentieth century demonstrate the absolutely
unprecedented extent of human impacts on the environment. These grave
global problems include climate change, depletion of the ozone layer, and
loss of biodiversity.
Two over-riding trends characterize the beginning of the third
millennium Reference: LE-6. First, the global ecosystem is threatened by grave
imbalances in productivity and in the distribution of goods and services. A
significant proportion of humanity still lives in dire poverty, and projected
trends are for an increasing divergence between those that benefit from
economic and technological development, and those that do not. This
unsustainable progression of extremes of wealth and poverty threatens the
stability of society as a whole, and with it the global environment. Secondly,
the world is undergoing accelerating change, with environmental
stewardship lagging behind economic and social development.
Environmental gains from new technology and policies are being overtaken
by population growth and economic development. The processes of
globalization that are so strongly influencing social evolution need to be
directed towards resolving rather than aggravating the serious imbalances
that divide the world today. Resolving these imbalances is the only way of
ensuring a more sustainable future for the planet and society.
Although earth's environment has gone through significant changes
over geological time, nothing like these global environmental problems –
climate change, depletion of the ozone layer, and loss of biodiversity – has
taken place during the history of human civilization. The breadth and depth
of environmental problems facing the world have pressed political leaders to
recognize that nature's abundance and resilience can not be taken for
granted.
1.2.1 Anthropogenic Climate Change

One of the largest specific environmental concerns facing us is
anthropogenic climate change, a complex global problem related primarily
to the use of fossil fuels, particularly by industrialized countries Reference: LE-7.
Burning peat, coal, oil, and natural gas releases stored carbon into the
atmosphere with profound consequences. Clearing land and cutting or
burning forests also increases the atmospheric carbon dioxide level.
Although the global carbon balance has shifted over geologic time, it had
been in a state of relative equilibrium since the last Ice Age, with balanced
17
amounts of carbon moving into and out of the atmosphere each year. The
climate and ecosystems that had prevailed during the development of
human civilization were linked to this balance. Carbon dioxide, the major
greenhouse gas affecting global climate (along with methane, nitrous oxide,
and others) is now at levels about 30% higher than in pre-industrial times.
After light energy from the sun penetrates our atmosphere and is absorbed
by the Earth's surface, it gets reradiated in the form of heat energy. It is
natural and beneficial that gases in the atmosphere trap this heat energy, as
this maintains our planet's average surface temperature near a comfortable
16°C. But the changes we have created in the composition of the Earth's
atmosphere, increasing the levels of greenhouse gases, results in more heat
being trapped by the atmosphere. On average, global temperatures have
already warmed over the last century, and the Intergovernmental Panel on
Climate Change estimates that temperatures will increase another 1.5 to
4.5°C over the next century. This would be a rate of climate change unlike
anything that has occurred in the last 10,000 years. The ramifications include
inundation of coastal cities, severe droughts in some areas, severe storms
and flooding elsewhere, shifts in availability of fresh water, changes in
agricultural productivity, spread of tropical diseases, and wildlife and plant
communities unable to adapt- with increased political unrest and
international tensions likely to follow Reference: LE-7.
1.2.2 Depletion of Stratospheric Ozone

Another global concern is depletion of stratospheric ozone Reference: LE-8.A
natural concentration of ozone is found in a sort of “layer” about 19km
above the Earth's surface, in the Earth's upper atmosphere. This protective
ozone layer shields the Earth and all living things from lethal ultraviolet
(UV) radiation emitted by our sun and thus are essential in making Earth's
lands and upper oceans habitable. Chlorofluorocarbons (CFCs), halons, and
other artificial compounds, which were in common use in developed
countries for decades as coolants for refrigerators and air conditioners,
propellants for aerosol sprays, and other purposes, gradually loft to the
upper atmosphere after release. There they act to increase chemical
reactions that break down ozone. This allows more UV radiation to reach
the Earth's surface, where the UV rays increase the incidence of skin cancer
and cataracts and may damage the human immune system as well as harm
other animals and plants on land and in the sea.
1.2.3 Loss of Biodiversity

A third major global environmental problem is the loss of biodiversity,
which respected biologist E.O Wilson has called “our most valuable but least
appreciated resource” Reference: LE-9.The significance of biodiversity loss was first
recognized as a global problem in 1980 in the Global 2000 report that
resulted from a study authorized by U.S. President Jimmy Carter.
18
Biodiversity or the diversity of life can be studied at different levels. Genetic
diversity involves the diversity of genes and thus of adaptive traits (e.g.,
behavioural traits, and resistance to drought, disease, and toxins) within a
species or other taxonomic division; genetic diversity increases the
likelihood that a species can avoid extinction. Species diversity refers to the
number of species; each species is interdependent with other species in
many ways. Ecological diversity involves diversity of ecological
communities. Habitat degradation and destruction is the major cause of
species loss. Much of the loss is occurring in tropical forest and other
species-rich ecosystems that are not well studied and where millions of
species remain unidentified. Some scientists think that as many as one-third
of all species on Earth could be extinct by 2100. The loss of each species
and the ecosystem services it provides may affect society in a number of
ways. Biodiversity, along with a few other factors including climate, species
composition, disturbance, and availability of nutrients, is a major controller
of the dynamics and structure of populations and ecosystems Reference: LE-10.
Because biodiversity acts to stabilize community and ecosystem processes,
we can expect human-caused losses of biodiversity to result in significant
long-term changes in the functioning of ecosystems.
1.2.4 Other Problems and Fut ure Threats

Anthropogenic climate change, stratospheric ozone depletion, and loss of
biodiversity are the three most significant worldwide problems facing us
today. Other local, regional, or global environmental concerns include air
pollution, acid rain, water pollution, decline of fish stocks, soil erosion,
deforestation, eutrophication, desertification, solid waste, and hazardous and
radioactive waste. Many of these concerns are linked to the size of the
human population, to consumption of goods and services by the human
population, and to policies and technologies that affect production and
distribution of goods and services. In addition to existing problems, we face
the possibility that entirely new problems (or unanticipated consequences of
current problems) could develop in the future.
1.3 Sustainability, Ecology and Engineering

As we saw from the last paragraph there is not such thing as
“unprecedented” environmental impacts or “phenomenal” catastrophic
occurrences in the 21st century but what it is clearly is a great environmental
problem, an accumulation of a series of undermining industrial and
engineering practices over the centuries and more importantly over the last
20 decades.
Many scientists today vindicate the fact that these practices were
necessary and vital for humanity to jump ahead in the evolution process and
that any accusations made for the results of them should be directed at the
19
soundness of their design and planning as these are the real culprits of the
problem itself. Others believe that the 21 st century civilisation is found
facing a crisis of economic, social and environmental projections. They state
that the extent of the crisis is such that we should be worried about the
continuity of our species, on this planet, for the years to come. According to
this party of people the human civilization has never encountered so big a
dilemma such a complex situation of accepting the current face of society,
and with it automatically the possibility of a future catastrophe, or rethinking
and redesigning today’s endless set of priorities and values that have caused
this crisis to ensure a better course of life. And complex this situation is.
Over consumption, industrialisation, the fight for economic consolidation
and the strife for rampant rates of growth, are some of the most important
characteristics of the face of the menace.
Humanity can today be proud of numerous amazing and impalpable
breakthroughs and achievements in every science of our intellectual
expressionism. These creations though, when viewed from a different angle,
they can be deemed as detrimental and corrosive to the environment
primarily and to society and economy secondarily as they can be proved
beneficial at the same time, a fact that overshadows their glamour and
importance to us. The spinal chord of our revolutionary methods to flourish
has been found today of having a negative effect on the planet. The choice
of materials for our products, the way manufacture our products, the way
we produce our energy, the way we produce our food, the way we dispose
our wastes and many others are an example of the synchronous case of the
environmental problem we experience today. To no dereliction and as an
integral part of the crisis there are other sectors that flaw in today’s polis,
economical and social in nature (like the huge differences in the monetary
status of many countries of the west and the south or the social paralysis of
minorities in many nations Reference: LE-6) , which constitute the range of the
problem. It was soon realised that these three flaws of today’s civilisation are
so detrimental to the next generations to be left unnoticed and ungoverned
and the term sustainability was readily appointed to the problem as a
scientific description for studying it.
The conceptual underpinnings for our current use of the term
sustainability originate in the early 1970s. The book “Blueprint for Survival”
called for “a stable society - one that to all intents and purposes can be sustained
indefinitely while giving optimum satisfaction to its members” Reference: LE-11. In the early
1980s, the phrase sustainable development began to appear in
publications of the United Nations and the idea of sustainability was
discussed by the private sector as well, such as in the Worldwatch Institute
book “Building a Sustainable Society” Reference: LE-12. Yet it was not until the 1987
publication of “Our Common Future” by the World Commission on
Environment and Development that sustainable development was discussed
as a major political goal and defined in a way that drew the attention of the
20
world. Often called the “Brundtland Report” after the Norwegian prime
minister who chaired the commission, this report to the United Nations
decried the usual narrow approach to environmental issues or economic
development issues and called for new approaches that would integrate
ecological, economic, and social concerns Reference: LE-13 .The report discussed the
need to apply integrated, sustainable solutions to a broad range of problems
related to population, agriculture and food security, biodiversity, energy
choices, industry, and more. It emphasized that building a sustainable
society will require enhancing the quality of life for all humanity without
impacting the long-term carrying capacity of natural systems. At the 1992
United Nations Conference on Environment and Development in Rio de
Janeiro, also called the Earth Summit, sustainable development was an
underlying theme. The “Rio Declaration on Environment and Development”
outlined the obligations and rights of countries in pursuing sustainable
development, and an ongoing UN Commission on Sustainable
Development was created Reference: LE-14.
In Our Common Future, the Brundtland commission proposed the
definitionDefinition for sustainable development that was to become so broadly
used by so many scientific teams Reference: LE-13 . The Brundtland report
described seven strategic imperatives for sustainable development:
• Reviving growth,
• Changing the quality of growth,
• Meeting essential needs for jobs, food, energy, water, and
sanitation,
• Ensuring a sustainable level of population,
• Conserving and enhancing the resource base,
• Reorienting technology and managing risk and
• Merging environment and economics in decision-making.
It also emphasized that the state of our technology and social organization,
particularly a lack of integrated social planning, limits the world’s ability to
meet human needs now and in the future. Sustainable development or
sustainability involves three broad interacting realms: environment,
economics, and social equity. These three realms could be called the
ecological imperative, the social imperative, and the economic imperative. It
has been said that: “These three aspects are inseparable and our ability to develop a
deeper understanding of this linkage is critical to our prospects for sustainability” Reference:
LE-15
.
Definition “Sustainable development is development that meets the needs of the present without compromising the ability of future generations to meet
their own needs”
21
1.3.1 The Principle of Environmental Health and Engineering
The long-term health and stability of natural systems are critical to human
society. Not only do natural systems provide natural resources or ecosystem
goods but also a range of other ecosystem services that support human life
and endeavours Reference: LE-16.Environmentally sustainable choices would
include those which contribute to conserving natural resources, protecting
biodiversity, stabilizing atmospheric composition and global climate, and
otherwise protecting the stability and productivity of Earth systems. Social
equity and economic development can support healthy environmental
systems (See Table 1.2)
Table 1.2/ Ecosystem services and functions Reference: LE-16

Natural regulations of populations by keystone predators or
Biological control
other tropic relations
Regulation of global temperature, precipitation, and other
Climate regulation
biologically mediated climatic processes
Non-commercial aesthetic, artistic, educational, spiritual,
Cultural
and/or scientific values of ecosystems
Dampening of ecosystem response to environmental
Disturbance
fluctuations – protection from storms, flood control, drought recovery,
regulation
and other processes mediated by vegetation structure
Ecosystem service Examples of ecosystem functions
Erosion control / Retaining soil within an ecosystem / prevention of loss by
sediment retention wind, runoff, or other processes
Food production Production of food crops, nuts, fruits, fish, game
Regulation of atmospheric chemical composition - CO2/O2
Gas regulation
balance, O3 for UVB protection
Sources of unique biological materials – medicine, genes,
Genetic resources
products for materials science
Storage, cycling, processing, acquisition of N, P, and other
Nutrient cycling
elements or nutrients; nitrogen fixation
Movement of floral gametes, allowing reproduction of wild
Pollination
plant populations and crop plants
Raw materials Production of lumber, fuel, and fodder
Recreational opportunities like ecotourism, sport fishing, and
Recreation
other outdoor activities
Habitat for resident and migratory populations of harvested or
Refugia
other species
Soil formation Weathering of rock and the accumulation of organic material
Breakdown of certain nutrients, co mpounds, or materials,
Waste treatment
including absorption of pollution and detoxification
Regulation of hydrological flows and provisioning of water for
Water regulation
agriculture, industry, transportation
Storage and retention of water by watersheds, reservoirs,
Water supply
aquifers
For today’s “developing” sciences like engineering the challenge of

ratifying the above principle is grater than ever. Technology, which has been
largely responsible for the decay of the environment, is by definition the
22
birth of engineering minds. It would be a true disappointment for the
science which focus has always been the improvement of our lifestyle to
relinquish to a superficial role coming from disrespecting environmental
appeals. To prevent this degradation the purity of engineering has been
reassessed to a sustainable level. The term “Green engineering” is given
today to the systems-level design of a process or product using
environmental attributes as a primary design variable. These design variables
are:
• Pollution prevention and waste minimization

• Solid waste reduction
• Recycling-based manufacturing
• Energy efficiency
• Renewable energy development
• Green business and environmental technologies development
• Link economics, environment, and social equity
• Informed citizens
• Use of market forces
Green Engineering is now a cross-disciplinary topic addressing a wide

range of methodologies, approaches, and areas of concern across various
engineering disciplines. The ultimate goal of such a discipline is to establish
a set of Green Engineering Principles that can serve as guidance for
engineers in the design of products and processes within the constraints of
sustainable development. The principles will not be prescriptive rules, but
rather a set of guidelines for the engineer to use that will improve the
environmental performance of the design as it interacts in a larger system
and affects the global ecosystem.
1.3.2 The Dark Side of the Energy Industry

Energy is both a solution and a problem for sustainable development. It
makes development possible, yet it is also a major cause of air pollution and
other damage to human health and the environment. Modern energy
services, dominated by the burning of fossil fuels, can vastly expand the
number of opportunities and choices available to people as they seek to
improve their standard of living and to power automobiles, airplanes,
factories and homes. Yet such energy generation results in air pollution and
emissions of greenhouse gases that contribute to global warming and
potential climate change.
Almost all energy production and use involves some form of
pollution of our environment. Each different source of energy, from fossil
fuels to nuclear, pollutes in a different way and to a different degree (Table
1.3). Just how much pollution and what type of pollution are acceptable and
23
which source of energy should be used has generated a lot of controversy
Reference: IS-3
.Carbon dioxide, one of the most prevalent greenhouse gases in the
atmosphere, has two major anthropogenic (human-caused) sources: the
combustion of fossil fuels and changes in land use. Net releases of carbon
dioxide from these two sources are believed to be contributing to the rapid
rise in atmospheric concentrations since pre-industrial times. Because
estimates indicate that approximately 80 percent all anthropogenic carbon
dioxide emissions currently come from fossil fuel combustion, world energy
use has emerged at the centre of the climate change debate Reference: IS-4. Many
countries currently have policies or regulations in place that limit energy-
related emissions other than carbon dioxide.
Criteria pollutants such as sulphur oxides and nitrogen oxides are also
emitted as a result of fossil fuel combustion, contributing to a variety of
health and environmental problems that include acid rain, deterioration of
soil and water quality, and human respirator illnesses. Nitrogen oxide
emissions additionally contribute to the formation of ground-level ozone
(smog). Furthermore, criteria pollutants indirectly affect the global climate
by reacting with other chemical compounds in the atmosphere to form
greenhouse gases or, in the case of sulphur dioxide, by affecting the
absorptive characteristics of the atmosphere. To date, the measures taken to
mitigate criteria pollutant emissions have been focused primarily on the
main sources. Fossil fuel combustion for electricity generation, particularly
coal-fired power, represents the largest source of sulphur dioxide emissions
in many countries. Other significant energy-related sources include fuel
combustion for manufacturing industries, vehicles, and petroleum refining.
Nitrogen oxides are emitted as a result of fossil-fuel-based electricity
generation, although oil use for road transportation is generally the single
largest source.
Energy production has another contributor to the environmental
hazards of the planet. The fission nuclear power plants that are already in
use have produced thousands of tons of radioactive waste that are sitting in
drums waiting for disposal. This waste will be toxic for thousands of years
and where to put it has become a gigantic technical and political problem.
For this kind of wastes there is still no safe storage methods and if any
proposed they are usually unproved and still under development for their
environment and public protection standards. While radiation leaks are rare,
there have been some small leaks and even a few larger ones. Small leaks
allow radioactive gases to get into the atmosphere, which if breathed, could
help cause cancer. The water from the cooling towers contains excess heat
energy and is released into the local rivers or lakes. The warmer
temperatures that are created allow organisms that would not normally
thrive to grow and kill off some of the previous inhabitants.
24
Table 1.3/ Pollutants and their Effects from Energy Power Plants
Coal & Oil Power Plants
Pollutant (air) Environmental Effects
Nitrous Oxides (air) Global Warming
Carbon Dioxide (air) Smog
Particulate or Dust (air) Causes lung cancer and other lung ailments
Nuclear Power Plants
Radioactive Waste (liquid or solid) Difficult to dispose of
Radiation Leaks (air) Radiation poisoning and increased risk of cancer
Heat Emissions (water) Causes growth of algae and kills marine life
1.4 A New Spawn

In an effort to deal holistically with the problem of sustainability groups of
people put together their efforts and their knowledge to gene communities
of 500-2000 members in which the ideals of life, environment and progress
were accepted as a balanced qualitative mix within a well defined region.
These villages append environmental and sustainability problems into a
radical form of natural inhabiting, endowed with the term Eco-Village (EV)
living.
Eco-Villages are in essence a modern attempt by humankind to live in
harmony with nature and with each other. They represent a “leading edge”
in the movement towards developing sustainable human settlements and
provide a testing ground for new ideas, techniques and technologies which
can then be integrated into the mainstream. The need for developing
sustainable human settlements relates directly to the commitment by the
world leaders at the Earth Summit in Rio (1992) to programs that will move
humanity to sustainability in the 21st century (Agenda 21). To achieve the
goals of sustainable human settlements, there is a need for pilot
communities, and for an exchange of information between them and the
mainstream. The EV movement embodies theory and practice centred on a
move from the current system which is deemed “narrow”, “utilitarian”,
“materialistic” and “reductional” to one which is “holistic”, “just”,
“ecologically sound” and controlled by local communities Reference: IS-5. The
formation of and ongoing operation of eco-villages has two major lessons
for the wider framework of sustainability:
1. It is an ongoing experiment in sustainable communal living where

new (and re-discovered old) solutions can be tried out on a smaller
scale before they can be applied at larger societal levels. As such they
act as demonstration sites for new technologies, new social and
economic arrangements.
2. They can be evolutionary in their practices as understanding of the
multi-faceted nature of sustainability increases, and as the need for
25
resource conservation/reduced environment impact at both a global
and local scale increases.
Such ecologically-based communities on a village scale start small, mainly

due to a lack of resources. However, they are large enough to encompass all
the necessary and essential elements of the human habitat in need of
transformation, and can continue with little support and minimal
opposition. For these villages the provision of goods comes directly from
natural resources including energy, food and water- autonomous
communities- with very little or not at all help required by exogenous
sources. Many are the merits of these communities concerning social and
economic breakthroughs but surely from an engineering perspective there is
a great interest for the ingenious techniques and practices that they utilise to
succeed their modernised needs in terms of efficiency and quality. One of
the most important EV issues is how to make technology ecologically,
socially and spiritually responsive to human needs, rather than the opposite.
For these micro societies it is the technology that tends to determine the
structure and organisation of society contrary to the contemporary society’s
technology, which promotes unliveable mega cities, separation of work and
home, institutionalisation of family support functions, environmental
degradation, un-sustainability, and over-consumption, in a centralised,
hierarchical structure. A vision of Eco-Villagers requires a radical change in
structure that would reverse all of these tendencies. To succeed that they
have adopted a renewable strategy concerning production, management,
distribution and conservation of energy and that is no other than promoting
sustainable technologies. Three key criteria have emerged in assessing
appropriate technologies for eco-villages, over and above commercial
viability:
1. Ecological sustainability.
2. Human scale, decentralised production.
3. Allowance for a non-stressful, meditative life style.
1.5 Auton omous Energy Rendition and Renewable Energy

Integration
The idea of rendering a community self-sustained is the ultimate goal of an
EV. But this is no easy task for any of the dimensions of making this
autonomy a reality never mind the energy field. This task becomes even
more difficult if the study has to employ power technologies that not only
are efficient but they would need to be appropriate enough for the type of
energy demand of a given EV and above all they would subject to the
conditions of being green and sustainable. Under these conditions the
autonomy can only come true with the use of Renewable Supply
26
Technologies (ReST). The true nature of the energy demand has two faces.
One is the Electrical Energy supply and the other is the Thermal Energy
supply. These two constitute the magnitude of the energy requirements for
any modern community and that is also the case for the EV. For both parts
there are plenty of candidates to utilise but the crux for the engineers is to
test the ability of ReST to mix in with the specialised energy needs of the
EV communities. The most widely used method for testing the potential of
ReST and thus aiding their integration is by Demand-Supply Matching (D-
SM) Reference: LE- 17.
The matching procedure described by Ramakumar et al. Reference: LE-23
employs a knowledge-based approach in the design of integrated renewable
energy systems. The procedure uses seasonal data sets to characterise each
season by a set of available RE resources and load requirements. By
systematically attempting to satisfy each of the seasonal demands with the
cheapest supplies available, seasonal supply systems are constructed, from
which an annual design is proposed. The work is primarily concerned with
finding the most economic supply technologies to satisfy a number of
prioritised demands. Again the high levels of variability involved in both
demand and supply profiles are neglected in a seasonal approach. Profile
variability is critical in any supply and demand matching exercise, as net
supply and demand totals give no indication as to whether demands are
satisfied at the time when they are required. The design of a renewable
energy system should ensure that times of renewable energy availability
coincide with periods of consumption.
So D-SM is a very arduous technique especially when the energy
engineers have time limitations upon delivery of the decisions plans and in
the case where the study has to be a realistic simulation (not a mere
estimation) of the pragmatic energy loads with respect to the topology and
the climatic characteristics of the area under development. For their aid, as
this is the case now for most of the engineering disciplines, computers are
utilised where very specialised programs can be run to improve the D-SM
process and so offer an incredible amount of capabilities for the integration
of ReST. Computer power has been largely responsible for the advances in
renewable technologies and will be equally instrumental in their
dissemination. The use of computer systems has had a direct effect on
renewable energy technologies by advancing design and improving
efficiencies Reference: LE-18. Examples include improving the conversion
efficiency of photovoltaic cells, increasing the aerodynamic performance of
wind turbines and the development of power electronic devices to allow
variable-rotor-speed operation of wind turbines, which reduce structural
loads and improve power quality.
27
Post-Development Phase
For the post development phase of an EV i.e. after the buildings have
erected, there is a variety of energy tracking and decision support systems
are currently available (e.g. QuickPlan and Entrack Reference: LE-19). These
software tools enable users to monitor energy consumption in order to
detect inefficiencies and faulty control systems, and evaluate the effects of
building retrofits. They also provide spatial information related to enable
renewable energy resource estimation by site, as well as environmental and
socio-economic impact assessment. The EEP system Reference: LE- 20 enables
sustainable planning via emissions tracking and enables users to assess
progress towards agreed reductions in emissions. Furthermore about the
simulation of building demands involved in the appraisal of energy
efficiency technologies there is range of software design tools are available,
encompassing simple appraisal tools (e.g. ASEAM Reference: LE-24, Energy 10
Reference: LE-25
and sophisticated packages (e.g. DOE-2 Reference: LE-26, Esp-r Reference: LE-
27
.These tools are employed to evaluate a variety of energy dependent
design measures, with the more advanced packages including features to
assess comfort, daylight and analyse different control systems. Furthermore,
some of the building simulation tools incorporate renewable energy
technology modelling, allowing building integrated system analysis (e.g. Esp-
r).
Pre-Development Phase
When the study is at the pre-development phase there is still a large family
of computer software that can assist and facilitate the decision making for
ReST for an EV. The author is referring to that family as Computer
Simulation Methods for Renewable Technology Integration or CoSiMReTsI.
There are many specialised simulation tools that are available for the analysis
of renewable systems. Examples include solar ventilation air heating;
biomass heating; wind energy; small hydro and photovoltaic systems (e.g.
RETScreen Reference: LE-21, IRES-KB Reference: LE-22.Such programs facilitate the pre-
feasibility analysis of renewable technologies and aid the procedure of
evaluating the optimum technology for a given site by the evaluating supply
potentials. Among others there is MERIT Reference: IS-6, the program that we
used in this study is, which is a very versatile software to facilitate the
simulation for the D-SM of the Tweed Valley EV. The fundamental aim in
the creation of MERIT is to ensure its use was not limited to specialist
knowledge and could be used by computer literate individuals to investigate
various supply and demand strategies, without the need for prior knowledge
of different technologies.
28
End of Chapte r 1
29
Chapter 2-Literature Rev iew
This chapter is dedicated to the essential background information accompanying the experimental phase of the
project. The focus will be addressing the renewable technologies that will be used in later chapters providing basic
and advanced knowledge of their technical characteristics that will endorse the experimental study. The Eco-Village
notion as a global phenomenon and as a Scottish reality at the Tweed Valley will also be acknowledged to deliver
an understanding of the values and principles of these radical communities.
2.1 A Brave New World

Eco-Villages are in essence a modern attempt by humankind to live in
harmony with nature and with each other. The need for developing such
sustainable human settlements relates directly to the commitment by the
world leaders at the Earth Summit in Rio (1992) to programs that will “move
humanity to sustainability in the 21st century” (Agenda 21). To achieve such
goals of sustainable human settlements, there is a need for pilot
communities, which will provide a testing ground for new ideas, techniques
and technologies which can then be integrated into the mainstream. These
housing models would seek to encourage the social, economic and
environmental notions of sustainability through good design, green
technologies and fostering of community.
This movement towards sustainable communities has a number of
precedents, notably in the utopian literature Reference: LE-28, 29, 30,31, and in various
historical attempts to establish social utopian experiments in many countries
around the world like the Tolystoyian communes in Tsarist Russia, umayaa
villages in Tanzania, New Harmony, Brook Farm and other experiments in
19th century United States. Today the Eco-Village movement is represented
by the Global Eco-Village Network (GEN) Reference: IS-5 which comprises
projects from all over the world at different stages of development, the
oldest established more than 25 years ago and the most recent being under
establishment. The first groups (seed groups) were a splendid effort of
experiments to put together a rather virtual and extemporaneous dream of
an alternative but concrete society within the limits of contemporary society.
The experiments were implemented on a trial and error basis and the results
were plain but impressive. Over the years, science was included in the
planning to provide design and application guidelines in the directions of
sustainability and spirituality. Some of the initial projects include:
• The Findhorn Foundation, Scotland.

• Lebensgarten, Germany
• Ecoville Nevo and Rysovo, Russia
• Gyûrûfû, Hungary
• Crystal Waters, Australia
• The Farm, USA
30
• The Manitou Foundation, USA
• The Ladakh project, India
• Danish Eco-village Association
Most of these projects are now internationally well recognised, while

the projects in Eastern and Central Europe are in the start-up phase Reference: IS-
5
. Common to all of the projects is their focus on education and a desire for
the integration of ecology, spirituality, community, and business
development. Each of the projects functions as an eco-village training centre
for their area. The range of skills that are on offer is very extensive, covering
all aspects of sustainable community living.
2.1.1 Organizational and Design Principles

An eco-village, as defined by Robert Gilman of the GEN Reference: IS-5, is a:
“Human scale, fully featured settlement,

Which integrates human activities harmlessly into the natural environment,
supports healthy human development,
And can be continued into the indefinite future”.
He believes that to achieve a truly sustainable community it must have:
1. Conscious awareness of the interrelationships of all life and the cyclic

sustainable systems of nature,
2. Understanding of and support for cultural, social and spiritual values
of this awareness and how humans can live ecologically balanced lives
3. Viable technologies that do not further harm, but which help to heal
the planet.
He suggests that eco-villages can also be testing grounds for new ideas,
technology and techniques which can then be integrated into the
mainstream. Eco-village settlements need to meet various organizational
challenges in building and in operating more sustainable systems. These
challenges are:
• The bio system challenge of integrating eco-village activities

harmlessly into the surrounding environment,
• The built environment challenge of using sustainable materials and
technology for shelter, transport and economic activity,
• The economic system challenge of providing sustainable
economic activity that is non-exploitative of nature and humans
and which is satisfying,
31
• The governance challenge of defining the roles, expectations and
practices of decision making and resource allocation within such
communities, and their relationship with others,
• The “glue” challenge of setting out an ideal of a shared vision, and
the resulting tensions between unity of purpose and diversity of
practice,
• The “whole system” challenge of integrating and meeting the
above challenges in a personally satisfying and sustainable process
within an existing economic and social system which currently
wasteful of resources and unsustainable.
Eco-villages attempt to meet these challenges by adopting design

principles to guide their initial establishment and continued functioning.
These principles or design features attempt to define an ideal situation
which any given eco-village may be in process of moving towards. The five
principles Reference: LE-32, 33 are defined as being:
• Human scale – of such a size and proximity that face to face

relations are possible. This applies also to neighbour-hoods as well
as hamlets and villages.
• Fully featured – where all the major functions of living-work,
recreation, social and commerce are present and where design
caters for the full span of human age (infants to elderly) and for
various physical conditions.
• Ecologically sensitive in that the design respects other life forms,
and obeys cyclical patterns of resource use instead of once-
through and dispose.
• Healthy human development – where there is a balanced and
integrated development of all aspects of human life – the physical,
emotional, mental and spiritual; and where both individual and
community well-being is recognised and catered for; and where
structures are established for community economics, community
governance and satisfying social relationships.
• Sustainability obedience – where there is recognition of and
commitment to not live off accumulated capital and anti-
ecological activities elsewhere.
Clearly these are challenging principles and existing eco-villages are at

different stages in their evolution in recognising and meeting these
requirements.
2.1.2 The Secrets for Green Practices

To these communities there are no so called secrets of living harmonically
with the natural environment and enjoy the luxuries of modern civilisation
32
at the same time. That is because common to all of the projects is their
focus on education and a desire for the integration of ecology, spirituality,
community, and business development.
Eco-Villages recognition of environmental impacts and principles is
strong. Most of the eco-villages are using the environment to cover there
needs to an autonomous level and so energy, waste treatment, water, and
food production are provided on site. Energy needs are met usually by solar
and wind, water is supplied by rainwater catchments, wastes and nutrients
are recycled and treated as resources, local forests provide building
materials, and annual vegetable production and perennial fruit production
are integrated into the project. Common land contains the infrastructure
network–roads and walkways, power and communication systems, as well as
dams for water supply and fire fighting. Common land also safeguards
natural features and gives space to wildlife. Most householders compost
their organic waste; inorganic waste is likely to be recycled for building
materials. Water for household needs is collected from rainwater tanks, and
additional garden supplies are available from storage dams. Sewage or black
waste is either taken care of by composting toilets or through septic tanks.
Some households install grey water subsurface or reed bed systems.
2.1.2.1 Permaculture
One of the three characteristics, for which eco-villages are known to wider
public, is the practice of permaculture as a mandatory planning issue. The
word "permaculture" was coined in 1978 by Bill Mollison, an Australian
ecologist, and one of his students, David Holmgren. It is a contraction of
“permanent agriculture” or “permanent culture”.
Permaculture is about designing ecological human habitats and food
production systems. It is a land use and community building movement
which strives for the harmonious integration of human dwellings,
microclimate, annual and perennial plants, animals, soils, and water into
stable, productive communities. The focus is not on these elements
themselves, but rather on the relationships created among them by the way
we place them in the landscape. This synergy is further enhanced by
mimicking patterns found in nature. A central theme in permaculture is the
design of ecological landscapes that produce food. Emphasis is placed on
multi-use plants, cultural practices such as sheet mulching and trellising, and
the integration of animals to recycle nutrients and graze weeds. However,
permaculture entails much more than just food production. Energy-efficient
buildings, waste water treatment, recycling, and land stewardship in general
are other important components of permaculture. More recently,
permaculture has expanded its purview to include economic and social
structures that support the evolution and development of more permanent
communities, such as co-housing projects and eco-villages. As such,
permaculture design concepts are applicable to urban as well as rural
33
settings, and are appropriate for single households as well as whole farms
and villages.
“Integrated farming” and “ecological engineering” are terms
sometimes used to describe permaculture, with “cultivated ecology” perhaps
being the closest. Though helpful, these terms alone do not capture the
holistic nature of permaculture; thus, the following definitions are included
here to provide additional insight.
2.1.2.2 Co-Housing
The other characteristic of eco-villages is the practice of co-housing. Co-
housing is the name of a type of collaborative housing that attempts to
overcome the alienation of modern subdivisions in which no-one knows
their neighbours, and there is no sense of community. It is characterized by
private dwellings with their own kitchen, living-dining room etc, but also
extensive common facilities. The common house may include a large dining
room, kitchen, lounges, meeting rooms, recreation facilities, library,
workshops, and children’s space.
Usually, co-housing communities are designed and managed by the
residents, and are intentional neighbourhoods: the people are consciously
committed to living as a community; the physical design itself encourages
that and facilitates social contact. The typical co-housing community has 20
to 30 single family homes along a pedestrian street or clustered around a
courtyard. Residents of co-housing communities often have several optional
group meals in the common building each week. This type of housing began
in Denmark in the late 1960s, and spread to North America in the late
1980s. There are now more than a hundred co-housing communities
completed or in development across the United States and Canada. The
main characteristics of Co-housing are Reference: LE-34:
1. Participatory Process. Residents participate in the planning and design

of the development of the community so that it directly responds to
their needs.
2. Neighbourhood Design. The physical design encourages a sense of
community as well as maintaining the option for privacy.
3. Private homes supplemented by common facilities. Common facilities
are designed for daily use; they are an integral part of the community
and typically include a dining area, sitting area, children’s play room,
guest room, as well as garden and other amenities. Each household
owns a private residence (complete with kitchen) but also shares
extensive common facilities with the larger group.
4. Resident management. After move-in.
5. Non-hierarchical structure and decision-making. There are leadership
roles, but not leaders.
6. The community is not a primary income source for residents.
34
2.1.2.3 Ecological and Sustainable Building Design
The last of the three most important characteristics and maybe the one with
the uppermost significance from an engineering perspective is the practice
of sustainable constructions for the people of the EV. There are two
approaches that Eco-Villagers implement the design of their buildings: the
green or ecological approach and the sustainable one. The two are too
difficult to distinct as they both focus on the improvement of habiting and
the protection of the environment, but still there are some slight differences
that separate them.
Green Building
A green approach to the built environment involves a holistic approach to
the design of buildings. The design methods usually integrate passive solar,
energy efficiency and other renewable energy technologies that can be used
to reduce building energy consumption. This high performance, holistic
approach to design examines how a building interacts with its systems,
activities and surrounding environment. Thus by optimising the building’s
standard components- site, windows, walls, floors and mechanical systems-
building owners can substantially reduce energy use without increasing
construction costs. All the resources that go into a building, be they
materials, fuels or the contribution of the users, need to be considered if a
sustainable architecture is to be produced. Producing green buildings
involves resolving many conflicting issues and requirements. Each design
decision has environmental implications. Measures for green buildings can
be divided into four areas:
• Reducing energy in use,

• Minimising external pollution and environmental damage,
• Reducing embodied energy and resource depletion,
• Minimising internal pollution and damage to health
A green building places a high priority on health, environmental and

resource conservation performance over its life-cycle. These new priorities
expand and complement the classical building design concerns: economy,
utility, durability, and delight. Green design emphasizes a number of new
environmental, resource and occupant health concerns:
• Reduce human exposure to noxious materials,

• Conserve non-renewable energy and scarce materials,
• Minimize life-cycle ecological impact of energy and materials used,
• Use renewable energy and materials that are sustainably harvested,
• Protect and restore local air, water, soils, flora and fauna,
• Support pedestrians, bicycles, mass transit and other alternatives to
fossil-fuelled vehicles.
35
Most green buildings are high-quality buildings; they last longer, cost less to
operate and maintain, and provide greater occupant satisfaction than
standard developments.
Sustainable Building
A sustainable construction on the other hand is defined as “the creation and
responsible management of a healthy built environment based on resource efficient and
ecological principles”. Sustainable designed buildings aim to lessen their impact
on our environment through energy and resource efficiency. It includes the
following principles:
1. minimising non-renewable resource consumption

2. enhancing the natural environment
3. eliminating or minimising the use of toxins
Sustainable buildings have minimum adverse impacts on the built and

natural environment, in terms of the buildings themselves, their immediate
surroundings and the broader regional and global setting. A sustainable
building will strive for integral quality (including economic, social and
environmental performance) in a very broad way. Thus, the rational use of
natural resources and appropriate management of the building stock will
contribute to saving scarce resources, reducing energy consumption (energy
conservation), and improving environmental quality. Sustainable building
concept involves considering the entire life cycle of buildings, taking
environmental quality, functional quality and future values into account. The
latter is dictated by a set of five objectives, which are reckoned as
architectural guidelines for the villagers:
• Resource Efficiency,
• Energy Efficiency (including Greenhouse Gas Emissions Reduction),
• Pollution Prevention (including Indoor Air Quality and Noise
Abatement),
• Harmonisation with Environment (including Environmental
Assessment),
• Integrated and Systemic Approaches (including Environmental
Management System),
2.1.3 The Vision of the Tweed Valley Eco-Village

The Tweed Valley EV is a concept of seven families living in Innerleithen
and Traquair of the Peeblesshire County in Scotland. The project will
involve 17 houses where these families and other will stay. Scotland is not
inexperienced in the development of EV (See Figure 2.1).
36
Figure 2.1/Eco-Village developments in Scotland
In search of new homes they came up with the idea of an Eco-Village. The
most appropriate site they could find was the Thornylee Forest (See Figure
2.2) provided by the Forest Enterprise. According to the overview of the
project by their prospect villagers this site has the following advantages
Reference: LE-35
:
• “South Facing Slope. This maximises the potential for solar energy
collection of all types including passive, photovoltaic, water heating
and it is important for the walled organic garden planned for the
paddock that will enable the villagers an autonomy on the food
following the principles of permaculture”.
• “Low Environmental Impact. Thornylee is a sheltered and
unobtrusive site. The houses will be designed to integrate into the
surrounding landscape with a very low visual impact using
environmental responsible materials (See P.2.1.2.3)”.
• “Rural Location. As a stated aim of the EV development its
construction on the Thornylee site would be a positive enhancement
on the countryside amenities, landscape and nature conservation
through the creation of new possibilities for leisure, relaxation and
tourism”.
• “Regeneration of Degraded Land. Vast areas around Thornylee are
dominated by plantation monoculture that supports few other
species and prevents biodiversity. A change of land use at Thornylee
37
from uneconomical forestry to recreational, educational and
residential use will promote local involvement and increase its
biodiversity through the planting of native species”.
• “Transport Corridor. The site is situated just off the main Peebles to
Galashiels road (A72) and is served by the Edinburgh to Galashiels
bus (No. 62)”.
• “Space. It is important to have a site where space is not restricted.
Thornylee Forest covers a large area (approximately 300acres) which
will provide ample space for living, working, the positioning of
energy systems and the provision of waste management through
Wetland (Reed Bed System) construction”.
Figure 2.2/Thornylee Forest and surroundings
As a genuine representative of the Eco-Village movement the Tweed Valley

project will embody all the organisational and design principles as described
in P.2.1.1.
When the author visited the Thornylee Forest for identifying the prospects
of installing ReST at that site he was surprised by the tremendous potential
that slope and hill composition could offer. The south face slope could offer
indeed the maximisation of solar energy collection (See Figure 2.3) and at
the top of the hill there is an amazing opportunity for wind energy
collection (See Figure 2.4). There is also a natural trough that acts as an
natural water capture reservoir where the other study (“Wind and Hydro Power
System for the Tweed Valley Ecovillage” Reference: LE-36) would be based (See Figure
2.5). It is thus not surprising that this study will examine the integration of
photovoltaic and wind turbines as the given ReST modules and will try to
simulate for the D-SM method (See P.1.5)
38
Figure 2.3/ South Facing slope
Figure 2.4/ Top of the Thornylee Hill
Figure 2.5/ Natural Reservoir
39
2.2 Let There Be Power
As we saw in paragraph P.1.3.3 one of the culprits for the environmental
integrity of the planet is the Energy Sector. The first of the two divisions,
the Electrical Generation Division (end-use electrical energy), is the most
dangerous with Energy Industry for Decentralised Fuel Demand (refined
oil, gasoline and natural gas fuels for domestic, transportation and industrial
use) following the track. Almost every hazardous element that can
contribute to the pollution and perturbation of the environment (land, air,
water) is found to have a direct or indirect connection with some means of
energy production.
Over the years, since the first realisation of the problem, the Energy
Sector was “revived” to a reasonable extend partly by introducing statutory
guidelines on the degree and nature of pollution and efficiencies or by
incorporating alternative (renewable) sources of energy generation to an
ancillary degree, where possible. One approach to reducing emissions is to
focus on increasing energy efficiency. Energy efficiency equates to money
saved while securing the energy supply Reference: LE- 37. The first statutory
amendments were applied to establish and enforce air pollution standards
and to set emission standards for new factories and extremely hazardous
industrial pollutants Reference: LE-38. The energy industry was highly affected by
that as it was required to meet “ambient air quality standards” by regulating
the emissions of various pollutants from existing stationary sources, such as
power plants and incinerators, in part by the installation of smokestack
scrubbers, electrostatic precipitators, and other filters. Later amendments
also expanded the scope and strength of the regulations for controlling
industrial pollution. The result has been limiting progress in reducing the
quantities of sulphur dioxide, carbon monoxide, nitrogen oxide, ozone,
particulate matter, and lead in the air. Some of these act also regulated
hazardous air pollutants such as mercury, beryllium, asbestos, vinyl chloride,
benzene, radioactive substances, and inorganic arsenic (EPA 1992).
But what really is a longer and more solid and robust solution to the
actual environmental problem is the use of technology capable of capturing
the renewable energy diffusion on the planet in terms of solar, wind,
elevation, fluid power, gravitational and bio-materials potential. Renewable
energy technologies were developed, in part, to combat the results of fossil
fuel depletion Reference: LE-37 but it was soon realised that these clean and
abundant tools of producing energy can have other benefits on areas of
economy and social promotion for both industrialised and developing
countries. As part of this project we are only interested to any solution that
can and it is used by the Eco-Village grid for covering the demand of these
organisations in energy consumption. It should be clear by now that the
selection of the following systems is in accordance to the relative need for
sustainable technology use within specific economic and regional availability
requirements for the habitats of eco-villages as described before in P.2.1.
40
With a combination of this technologies to the other sustainable principles
for housing planning the eco-villages are truly a purely form of static success
of a natural energy assimilation system.
2.2.1 Photovoltaic Systems

Photovoltaic (PV) technologies, also commonly known as “solar cells”, are
solid-state semiconductors. PV systems consist of two major subsystems of
hardware: PV modules and the Balance-of-System (BOS). PV modules
house an array of solar cells that deliver Direct Current (DC) power,
whereas BOS equipment include components needed for mounting, power
storage, power conditioning and site-specific installation ( See Figure 2.6). A
BOS system usually includes battery charge controllers, batteries, inverters
(for loads requiring alternating current), wires, conduit, a grounding circuit,
fuses, safety disconnects, outlets, metal structures for supporting the
modules, and any additional components that are part of the PV system.
Figure 2.6/ PV system components Reference: LE-39.
PV systems have several advantages: they are cost-effective alternatives in

areas where extending a utility power line is very expensive, they have no
moving parts and require little maintenance, and they produce electricity
without polluting the environment. Thus in a quick view the selection of PV
systems will depend on a variety of reasons such as:
• Cost-when the cost is high for extending the utility power line or
using another electricity generating system in a remote location, a PV
system is often the most cost-effective source of electricity.
• Reliability-PV modules have no moving parts and require little
maintenance compared to other electricity-generating systems.
• Modularity-PV systems can be expanded to meet increased power
requirements by adding more modules to an existing system.
41
• Environment-PV systems generate electricity without polluting the
environment and without creating noise.
• Ability to combine systems-PV systems can be combined with other
types of electric generators (wind, hydro, and diesel, for example) to
charge batteries and provide power on demand.
2.2.1.1 PV Technology
The basic element of photovoltaic technology is the solar cell (typically
10*10 cm2). Solar cells are constructed by joining two dissimilar layers of
semi-conducting materials, referred to as p-type (positive) and n-type
(negative) semiconductors. “Doping” a semiconductor, usually crystalline
silicon, with an impurity (typically boron) creates a deficit of negatively
charged electrons, producing a “p-type” semiconductor. Similarly, n-type
semiconductors are doped with small impurities, typically phosphorous, that
result in a surplus of free electrons. A solar cell is constructed by joining
these two semiconductors in a “p-n junction”, producing an electric field.
The photovoltaic effect is enacted when sunlight, comprised of positively
charged photons, is absorbed by the solar cell, transferring energy to the
electrons that then become part of a current in an electrical circuit. In
addition to the semiconductors, a solar cell consists of a transparent
encapsulant (typically glass) to prevent weathering, an anti-reflective layer,
and a contact surface to transfer the electric current to the load. Unlike
utility power plants, which produce electricity constantly despite the time of
day and year or the weather, the output of PV modules is directly related to
these three factors. Because different geographic regions experience
different weather patterns the location where the PV will be situated will
greatly vary the number of PV modules for a given power output.
Furthermore any seasonal variations can affect the amount of sunlight
available to power a PV system and thus its power output (See Figure 2.7).
The latter is also affected by fluctuations in the module temperature.
Figure 2.7/ The Sun’s path as a design factor for correct sizing, sitting and
positioning the PV
42
PV Modules
A PV module is an array of packaged solar cells that convert solar energy
directly into Direct-Current (DC) electricity. Individual PV module outputs
range between 10 Wp (peak Watts) to 300 Wp (each cell, measuring
approximately 10*10 cm2, generating 1Wp), but scaling allows PV modules to
be linked into panels and further, panels into arrays to meet the desired
electrical load Reference: LE-39. Virtually all of the installed PV systems in the
world are “flat-plate” systems that use large areas of semiconductors to
convert direct and diffuse solar radiation. While some flat-plate systems are
made to rotate to track the sun, most are fixed and have no moving parts.
Alternatively, PV systems known as “concentrators”, utilize optic lenses to
focus direct sunlight onto comparatively smaller areas, thereby reducing the
amount of necessary semi-conducting material. It is quite obvious that
dimension-wise these systems are in need of docking areas their size being
proportional to the power output of the PV modules. Figure 2.8 below is a
good example of how these two factors affect each other.
Figure 2.8/ Roof Area (sfeet 2) as a function of PV capacity
Crystalline Silicon PV
Silicon is the most common semi-conducting material in use in PV modules
due to its abundance. Single-crystal silicon, or mono-crystalline silicon,
semiconductors are the most efficient in transferring electrons due to their
uniform structure, but are also the most expensive. Excluding the market
for indoor-consumer-equipment with low power requirements, for example
a calculator, mono-crystalline silicon modules accounted for 48.4 MWp, or
60% of the 82.4 MWp global PV market in 1996 Reference: LE-40. A newer variation
of the mono-crystalline cell are silicon “ribbon” cells which are formed by
cutting ribbons from a thin mono-crystalline sheets. While silicon ribbon
cells hold promise of future manufacturing cost reductions, they constituted
just 3% or 3 MWp of the global market in 1996 Reference: LE-40. Crystalline silicon
PV cells have figured prominently in the commercial marketplace because of
their durability and efficiency performance. Today, modules constructed of
mono-crystalline silicon, yield efficiencies of 12% in the field. In laboratory
environments, module of crystalline silicon cells achieved efficiencies of
43
22.7% in 1998, up from 7% in 1976. Factors such as dust and encapsulants
reduce the light reaching the solar cells in the field and thus limit the
efficiency. The next most prevalent type of semiconductor is cast “multi-
crystal” or polycrystalline silicon, accounting for 24 MW, or roughly 30% of
the PV modules shipped in 1996. Polycrystalline silicon is less expensive to
manufacture than mono-crystalline silicon, however, it is less efficient in
transmitting electrons due to the existence of grain boundaries.
Polycrystalline silicon modules exhibit 9% efficiencies in the field.
Thin-film PV
An emerging alternative to crystalline silicon is thin-film PV. Thin-film, flat-
plate systems use 1/20 to 1/100 of the material needed for crystalline silicon
semiconductors by employing a film of semi-conducting material only 1
micron (10-6 m) thick. The most prominent type of thin-film photovoltaic in
production, Amorphous Silicon (a-Si), accounted for 5.9 MW or 7% of the
outdoor PV market in 1996 Reference: LE-40 .Two other thin-film PV under
development that demonstrate potential for large-scale PV module
manufacture are Cadmium Telluride (CdTe) and Copper Indium Diselenide
(CIS), though they held less than 1% of the PV market in 1996. Lower
material volumes for thin-film PV, as compared with crystalline silicon,
result in lower material costs. In principle, thin-film PV cells also exhibit a
greater propensity for mass-manufacturing cost reductions as compared
with crystalline silicon. However, commercially available thin-film PV have
not attained field efficiencies greater than 6%, as compared with the 12%
efficiency of crystalline silicon PV modules. Though laboratory tests have
yielded promising thin-film efficiencies, manufacturers have not yet
translated the high-efficiencies and high-yields of smaller, laboratory-
constructed thin-films up to production volumes. The economic
competitiveness of a PV module is measured in monetary currency per peak
watt (that is $/W p for the USA and £/Wp for the UK) and is therefore
impacted by both unit cost and efficiency. The challenge for thin-film PV
manufacturers is to consistently produce cells at commercial-scale
geometries and volumes with efficiencies akin to crystalline silicon cells, if
they are to capture more of the photovoltaic market.
2.2.1.2 Balance of System (B OS)

Ancillary equipment, referred to as the balance-of-system (BOS), is
necessary to install and deliver electricity from a PV module. BOS
requirements vary between applications due to site-specific power and
reliability requirements, environmental conditions, and power storage needs.
BOS components include mounting equipment such as frames and ballasts
to support and elevate the PV module/panel. A small portion of installed
PV systems also use tracking systems to follow the sun, thereby increasing
the exposure to incident sunlight. Power conditioning equipment limits
44
current and voltage, maximizes power output, and converts Direct-Current
(DC) electricity generated by the PV array into Alternating Current (AC)
electricity through a DC/AC inverter. Power storage is a desirable- or in
many instances a compulsory- power system requirement, and thus a battery
and a “charge controller” device must be added to the BOS. PV systems
necessitate protective electrical hardware such as diodes, fuses, circuit
breakers, safety switches and grounds, as well as wiring to connect the PV
module and BOS components Reference: LE-39. In applications where a PV system
will be supplementing a “base load” or where power must always be
available (i.e. nights or cloudy days), a PV system is usually integrated with
an auxiliary electric generator. This hybrid system does not necessarily fall
under the definition of BOS, but an additional electric generator will impact
the overall sizing of the PV system, the battery and other BOS components.
2.2.1.3 PV Applications
Solar cells are ideal energy candidates in niche markets where:
• Electric-grid extensions are not economical

• Peak electrical demand is coincident with maximum solar intensity
(e.g. cooling loads), or
• Where the attributes of PV technology as a clean and modular power
source are valued at a premium.
The PV market can be grouped into grid-connected and “stand-alone”

applications. Grid-connected applications- accounting for approximately 20-
30% of worldwide PV installations- include central PV stations or
distributed, small-scale PV systems sited near consumers. Stand-alone PV
applications are the most prevalent, constituting 60-70% of PV installations.
Some common examples of stand-alone PV system applications include
roof-top residential/commercial systems, remote water pumping stations,
telecommunications equipment, and individually powered appliances or
lights. As for every technology there is always a balancing set of characters
for the positive and negative side of PV Modules. For any application we
must weigh between them to check their suitability for the specific reasons
there are to be utilised. In general their advantages and disadvantages are
respectively:
Advantages
• Production of high quality electrical power (better than utility power
in most cases),
• On-site green power production – absolutely no emissions,
• Longevity, 20-30 year lifetime for most components, some will last
longer,
45
• Reliability, long periods between regular maintenance, 6-12 months,
• Provision of an uninterrupted power supply or UPS (when batteries
are included) during utility power outages,
• Silent & low maintenance, replaces noisy & unreliable generators,
• Solid State, no moving parts, nothing to break,
• Available anywhere in the world where there is light (even if no direct
sun!),
• Transportable, lightweight, good for mobile applications,
• Modular - expandable & easily up-gradable.
Disadvantages
• High initial cost
• Higher overall cost depending on situation
2.2.2 Wind Turbines
Wind turbines transform kinetic energy in the wind to electricity. The power
that can be generated from a modern wind turbine is practically related to
the square of the wind speed, although theoretically it is related to the cube
of the wind speed. This means that a site with twice the wind speed of
another will generate four times as much energy. Consequently, the
availability of good wind speed data is critical to the feasibility of any wind
project. Data is usually gathered over a period of time using anemometers
installed at the prospective site. Normally, one year is the minimum time a
site is monitored Reference: LE-40. Most commercial wind turbines operating today
are at sites with average wind speeds greater than 6 m/s or 22 km/h. A prime
wind site will have an annual average wind speed in excess of 7.5 m/s (or 27
km/h).
Key Points:
• Wind is an intermittent but predictable resource.
• Good wind speed data is critical to determining the economic
feasibility of a wind project.
• Prime sites have average wind speeds greater than 7.5 metres/sec (27
km/hr).
• Most common wind turbines in commercial operation average 600
kW in power capacity.
• Capacity factors range from 20 to percent; availability is greater than
95 percent.
• Wind is a modular technology that can be erected quickly.
• Wind turbines can be integrated into existing grid and off-grid
applications.
• Possible environmental issues include, visual, cultural, land use, and
bird impacts, and noise.
46
• Planning approval and environmental assessment are usually
necessary.
2.2.2.1 WT Technology
Almost all wind turbines are “horizontal axis” machines with rotors using
two or three airfoil blades. The rotor blades are fixed to a hub attached to a
main shaft, which turns a generator – normally with transmission through a
gearbox. The shaft, generator, gearbox, bearings, mechanical brakes and the
associated equipment are located inside the nacelle on top of the tower. The
nacelle also supports and transfers structural loads to the tower, and
together they house all automatic controls and electric power equipment.
The wind turbine automatically turns the nacelle to the direction facing the
wind for optimal energy production. The turbines are stopped at very high
wind speeds to protect them from damage.
Wind turbines range in capacity (or size) from a few Kilowatts to several
Megawatts. The crucial parameter is the rotor diameter – the longer the
blades the larger the area swept by the rotor, and thus the volume of air
hitting the rotor plane. At the same time, the higher towers of large wind
turbines bring rotors higher above the ground where the energy density in
the wind is higher. Larger wind turbines have proven to be more cost
efficient, due to improvements in designs and economics of scale, but also
with a higher energy production per swept m2, due to the higher towers. For
commercial utility-sized projects, the most common turbines sold are in the
range of 600 kW to 1 MW – large enough to supply electricity to 600-1,000
modern homes. Rotors may operate at constant or variable speeds,
depending on the design. MW-size machines are all variable speed concepts.
Typical rotor speeds at rated power range from 15 to 50 revolutions per
minute – a factor that influences the visual impact. The larger the rotor the
lower the rotational speed, in order to keep the blade tip speed in the
optimal range from 60 to 80 m/s. A typical 600 KW turbine has a blade
diameter of 35 metres and is mounted on a 50 metre concrete or steel tower.
Power output is regulated automatically as wind speed changes, to limit
loads and to optimise power production. The present state-of-the-art large
wind turbines have:
• Power control by active stall or pitch control (in both cases pitching
blades) combined with some degree of variable speed rotor and
• A two-speed asynchronous generator or a gearless transmission to a
multi-pole synchronous generator and power electronics.
Virtually all wind turbines installed at present are based on one of the three
main wind turbine types (See Figure 2.9):
47
This page has been removed
If necessary, contact:
Dr P. Strachan, Course Director

Energy Systems and the Environment MSc
paul@esru.strath.ac.uk
common, but more recent developments include wind-photovoltaic
units, a hybrid option which offers power generation from 100%
renewable sources.
Table 2.1/ Range of Power Outputs for WT installations

Nominal Power Typical Application
<1kW Micro’s
1-10kW Wind Home
10-200kW Hybrid Isolated Systems
200-1MW Grid Connected- single or in cluster
>1MW Offshore (or onshore wind farms)
Utility-sized commercial wind projects are usually constructed as wind farms

where several turbines are erected at the same site. Wind projects have been
successfully built to power a wide range of applications in diverse and often
extreme environments. One of the newest applications is to place wind
farms in shallow offshore areas where environmental impacts are often
lower and the availability of a steady, non-turbulent wind flow allows
turbines to operate more efficiently and generate more power. In off-grid
applications, wind generators can be combined with other energy sources,
such as diesel generators. The feasibility of a wind project, however, can be
influenced by access to the electrical grid. The need to install or upgrade
high voltage transmission equipment can significantly add to the cost of a
wind project. For off-grid and mini-grid applications, the combination of
wind/diesel or other sources can provide a greater percentage of overall
capacity.
Wind turbines are also a modular technology, which means they can
be installed as the capacity is needed. A small wind farm can usually be
constructed within year. Wind farms can be constructed as either
“builddown-operate” facilities under long-term power purchase contracts or
as turnkey facilities.
2.2.3 Hydrogen Fuel Technologies

Hydrogen is a fascinating carrier of energy. Its conversion to heat or power
is simple and clean and when combusted with oxygen it forms water which
means that no pollutants are generated or emitted. The water is returned to
nature where it originally came from. But hydrogen, the most common
chemical element on the planet, does not exist in nature in its pure
form. It has to be generated or produced by separating it from chemical
compounds. The two most common methods to produce hydrogen is from
water by electrolysis (green production) or from hydrocarbon fuels (or
any other hydrogen carriers) by reforming or thermal cracking (pollution-
53
intensive production). Other production methods include thermo-chemical
water decomposition, photo conversion and production from biomass.
Clean energies such as electricity from solar, wind and hydro can be applied
to produce clean hydrogen i.e. without greenhouse gases or nuclear waste
being generated in the production process (See Figure 2.14). At current
times hydrogen may actually be the only meaningful link between renewable
energy and chemical energy carriers Reference: LE-45.
Figure 2.14/Renewable technologies are the most sustainable and clean

method to produce hydrogen
2.2.3.1 Hydrogen Manufacturing, Electrolyser

The process of extracting hydrogen from water is called electrolysis. In
principal, electrolysis can be entirely non-polluting and renewable, but it
requires the input of large amounts of electrical energy. Consequently, the
total environmental impact of acquiring hydrogen through electrolysis is
largely dependent on the impacts of the source power.
In electrolysis, electricity is used to decompose water into its
elemental components: hydrogen and oxygen (Figure 2.15). Electrolysis is
often touted as the preferred method of hydrogen production as it is the
only process that need not rely on fossil fuels. It also has high product
purity, and is feasible on small and large scales. Electrolysis can operate over
a wide range of electrical energy capacities, for example, taking advantages
of more abundant electricity at night. At the heart of electrolysis is an
electrolyser. An electrolyser is a series of cells each with a positive and
negative electrode. The electrodes are immersed in water that has been made
electrically conductive, achieved by adding hydrogen or hydroxyl ions,
usually in the form of alkaline potassium hydroxide (KOH). The anode
(positive electrode) is typically made of nickel and copper and is coated with
oxides of metals such as manganese, tungsten and ruthenium. The anode
metals allow quick pairing of atomic oxygen into oxygen pairs at the
electrode surface. The cathode (negative electrode) is typically made of
nickel, coated with small quantities of platinum as a catalyst. The catalyst
54
allows quick pairing of atomic hydrogen into pairs at the electrode surface
and thereby increases the rate of hydrogen production. Without the catalyst,
atomic hydrogen would build up on the electrode and block current flow. A
gas separator, or diaphragm, is used to prevent intermixing of the hydrogen
and oxygen although it allows free pas-sage of ions. It is usually made of an
asbestos-based material, and tends to break apart above 80 ºC.
Figure 2.15/ Typical Electrolysis Cell
The rate of hydrogen generation is related to the current density (the

amount of current divided by the electrode area measured in amps per area).
In general, the higher the cur-rent density, the higher the source voltage
required, and the higher the power cost per unit of hydrogen. However,
higher voltages decrease the overall size of the electrolyser and therefore
result in a lower capital cost. State-of-the-art electrolysers are reliable, have
energy efficiencies of 65 to 80% and operate at current densities of about
2000 A/m2. For electrolysis, the amount of electrical energy required can be
somewhat offset by adding heat energy to the reaction. The minimum
amount of voltage required to decompose water is 1.23 V at 25 ºC. At this
voltage, the reaction requires heat energy from the outside to proceed. At
1.47 V (and same temperature) no input heat is required. At greater voltages
(and same temperature) heat is released into the surroundings during water
decomposition. Operating the electrolyser at lower voltages with added heat
is advantageous, as heat energy is usually cheaper than electricity, and can be
re-circulated within the process. Furthermore, the efficiency of the
electrolysis increases with increased operating temperature.
When viewed together with fuel cells, hydrogen produced through
electrolysis can be seen as a way of storing electrical energy as a gas until it is
needed. Hydrogen produced by electrolysis is therefore the energy carrier,
not the energy source. The energy source derives from an external power
generating plant. In this sense, the process of electrolysis is not very
different from charging a battery, which also stores electrical energy. Viewed
55
as an electricity storage medium, hydrogen is competitive with batteries in
terms of weight and cost. To be truly clean, the electrical power stored
during electrolysis must derive from non-polluting, renewable sources. If the
power is derived from natural gas or coal, the pollution has not been
eliminated, only pushed upstream. In addition, every energy transformation
has an associate energy loss. Consequently, fossil fuels may be used with
greater efficiency by means other than by driving the electrolysis of
hydrogen. Furthermore, the cost of burning fossil fuels to generate
electricity for electrolysis is three to five times that of reforming the
hydrogen directly from the fossil fuel. Non-polluting renewable energy
sources include hydroelectric, solar photovoltaic, solar thermal and wind.
2.2.3.2 Hydrogen Utilisation, Fuel Cells

A fuel cell is a device for directly converting the chemical energy of a fuel
into electrical energy in a constant temperature process. In many ways the
fuel cell is analogous to a battery, but a battery which is constantly being
recharged with fresh reactants. As well as offering a high theoretical
efficiency, especially at low temperatures, fuel cells emit low or zero levels of
pollutants, the have a quiet operation and few moving parts (only pumps
and fans to circulate coolant and reactant gases, respectively). They can run
on a wide range of fuels, ranging from gaseous fuels such as hydrogen and
natural gas to liquid fuels such as methanol and gasoline. Fuel cells could
potentially be used to replace conventional power equipment in many cases.
The main applications are likely to be in stationary power generation,
transportation, and battery replacement.
2.2.3.2.1 Generic FC Technology

The principle behind fuel cells was discovered as early as 1839 by Welsh
physicist and Judge Sir William Grove. However, due to high costs, the
technology was not significantly used until the American Gemini space
missions of the 1960's. For this and subsequent space missions, fuel cells
were thought to be safer than nuclear electric generation and cheaper than
solar. They have been thrust to the forefront of energy technology in the
1990's, however, as high power densities have made them feasible for both
stationary and portable applications.
The basic physical structure or building block of a fuel cell consists of
an electrolyte layer in contact with a porous anode and cathode on either
side. A schematic representation of a fuel cell with the reactant/product
gases and the ion conduction flow directions through the cell is shown in
Figure 2.16.
56
Figure 2.16/ How a FC works
In a typical fuel cell, gaseous fuels are fed continuously to the anode
(negative electrode) compartment and an oxidant (i.e., oxygen from air) is
fed continuously to the cathode (positive electrode) compartment; the
electrochemical reactions take place at the electrodes to produce an electric
current. A fuel cell, although having components and characteristics similar
to those of a typical battery, differs in several respects. The battery is an
energy storage device. The maximum energy available is determined by the
amount of chemical reactant stored within the battery itself. The battery will
cease to produce electrical energy when the chemical reactants are
consumed (i.e., discharged). In a secondary battery, the reactants are
regenerated by recharging, which involves putting energy into the battery
from an external source. The fuel cell, on the other hand, is an energy
conversion device that theoretically has the capability of producing electrical
energy for as long as the fuel and oxidant are supplied to the electrodes. In
reality, degradation, primarily corrosion, or malfunction of components
limits the practical operating life of fuel cells.
Gaseous hydrogen has become the fuel of choice for most
applications, because of its high reactivity when suitable catalysts are used,
its ability to be produced from hydrocarbons for terrestrial applications, and
its high energy density when stored cryogenically for closed environment
applications, such as in space. Similarly, the most common oxidant is
gaseous oxygen, which is readily and economically available from air for
terrestrial applications, and again easily stored in a closed environment. A
three-phase interface is established among the reactants, electrolyte, and
catalyst in the region of the porous electrode. The nature of this interface
plays a critical role in the electrochemical performance of a fuel cell,
particularly in those fuel cells with liquid electrolytes. In such fuel cells, the
reactant gases diffuse through a thin electrolyte film that wets portions of
the porous electrode and react electrochemically on their respective
electrode surface. If the porous electrode contains an excessive amount of
57
electrolyte, the electrode may "flood" and restrict the transport of gaseous
species in the electrolyte phase to the reaction sites. The consequence is a
reduction in the electrochemical performance of the porous electrode. Thus,
a delicate balance must be maintained among the electrode, electrolyte, and
gaseous phases in the porous electrode structure. Much of the recent effort
in the development of fuel cell technology has been devoted to reducing the
thickness of cell components while refining and improving the electrode
structure and the electrolyte phase, with the aim of obtaining a higher and
more stable electrochemical performance while lowering cost.
The electrolyte not only transports dissolved reactants to the
electrode, but also conducts ionic charge between the electrodes and thereby
completes the cell electric circuit, as illustrated in Figure ?? (above). It also
provides a physical barrier to prevent the fuel and oxidant gas streams from
directly mixing. The functions of porous electrodes in fuel cells are:
1. To provide a surface site where gas/liquid ionization or de-ionization

reactions can take place
2. To conduct ions away from or into the three phase interface once
they are formed (so an electrode must be made of materials that have
good electrical conductance), and
3. To provide a physical barrier that separates the bulk gas phase and
the electrolyte.
A corollary of the 1st function is that, in order to increase the rates of

reactions, the electrode material should be catalytic as well as conductive,
porous rather than solid. The catalytic function of electrodes is more
important in lower temperature fuel cells and less so in high temperature
fuel cells because ionization reaction rates increase with temperature. It is
also a corollary that the porous electrodes must be permeable to both
electrolyte and gases, but not such that the media can be easily "flooded" by
the electrolyte or "dried" by the gases in a one-sided manner.
A variety of fuel cells are in different stages of development. They
can be classified by use of diverse categories, depending on the combination
of type of fuel and oxidant, whether the fuel is processed outside (external
reforming) or inside (internal reforming) the fuel cell, the type of electrolyte,
the temperature of operation, whether the reactants are fed to the cell by
internal or external manifolds, etc. The most common classification of fuel
cells is by the type of electrolyte used in the cells and includes:
• Polymer Electrolyte Fuel Cell (PEFC) or Proton Exchange

Membrane Fuel Cell (PEMFC),
• Alkaline Fuel Cell (AFC),
• Phosphoric Acid Fuel Cell (PAFC),
• Molten Carbonate Fuel Cell (MCFC),
58
• Intermediate Temperature Solid Oxide Fuel Cell (ITSOFC), and
• Tubular Solid Oxide Fuel Cell (TSOFC).
These fuel cells are listed in the order of approximate operating temperature,
ranging from ~80C for PEFC, ~100C for AFC, ~200C for PAFC, ~650C
for MCFC, ~800C for ITSOFC, and 1000C for TSOFC. The operating
temperature and useful life of a fuel cell dictate the physicochemical and
thermo-mechanical properties of materials used in the cell components (i.e.,
electrodes, electrolyte, interconnect, current collector, etc.). Aqueous
electrolytes are limited to temperatures of about 200C or lower because of
their high water vapour pressure and/or rapid degradation at higher
temperatures. The operating temperature also plays an important role in
dictating the type of fuel that can be used in a fuel cell. The low-temperature
fuel cells with aqueous electrolytes are, in most practical applications,
restricted to hydrogen as a fuel. In high-temperature fuel cells, CO and even
CH4 can be used because of the inherently rapid electrode kinetics and the
lesser need for high catalytic activity at high temperature. However,
descriptions later in this section note that the higher temperature cells can
favour the conversion of CO and CH4 to hydrogen then use the equivalent
hydrogen as the actual fuel.
Table 2.2/ Summary of Major Differences of the Fuel Cell Types
PEMFC- A Brief Analysis

The type of fuel cell currently receiving the most attention is the PEM fuel
cell; PEM stands variously for “proton exchange membrane” or “polymer
electrolyte membrane”. The membrane is usually a perfluorosulfonic acid
polymer. This is a polytetrafluoroethylene (PTFE, trade name Teflon) chain
with side chains terminating in an SO 3H group. It is the hydrogen on this
sulfonate group that dissociates from the polymer when wet and appears as
59
protons in the solution; polymer acids have the advantage that the anion (–
SO3 - tail) is fixed in the electrolyte rather than dissolved. In the stack, the
fuel cells are arranged so that ions (protons) pass through the membrane,
while electrons are conducted through the separating graphite plates in the
opposite direction (Figure 2.17)
Figure 2.17/ Typical PEMFC schematic.
The PEMFC cell operates at a low 80C. This will result in a capability
to bring the cell to its operating temperature quickly, but the rejected heat
cannot be used for cogeneration or additional power. Test results have
shown that the cell can operate at very high current densities compared to
the other cells. However, heat and water management issues may limit the
operating power density of a practical system. The PEMFC tolerance for
CO is in the low ppm level. In general PEMFC deliver high power density,
which offers low weight, cost, and volume. The immobilized electrolyte
membrane simplifies sealing in the production process, reduces corrosion,
and provides for longer cell and stack life. PEMFC operate at low
temperature, allowing for faster start-ups and immediate response to
changes in the demand for power. The PEFC system is seen as the system
of choice for vehicular power applications, but is also being developed for
smaller scale stationary power.
2.2.3.2.2 Fuel Cell Stacking

Additional components of a cell are best described by using a typical cell
schematic, (See Figure 2.18). This figure depicts a PAFC. As with batteries,
individual fuel cells must be combined to produce appreciable voltage levels
and so are joined by interconnects. Because of the configuration of a flat
plate cell, the interconnect becomes a separator plate with two functions:
60
1. To provide an electrical series connection between adjacent cells,
specifically for flat plate cells, and
2. To provide a gas barrier that separates the fuel and oxidant of
adjacent cells.
The interconnect of a tubular solid oxide fuel cell is a special case, and the
reader is referred to Section 8 for its slightly altered function. All
interconnects must be an electrical conductor and impermeable to gases.
Other important parts of the cell are:
• The structure for distributing the reactant gases across the electrode
surface and which serves as mechanical support, shown as ribs in
Figure 2.18,
• Electrolyte reservoirs for liquid electrolyte cells to replenish
electrolyte lost over life, and
• Current collectors (not shown) that provide a path for the current
between the electrodes and the separator of flat plate cells.
Figure 2.18/ Expanded View of a Basic Fuel Cell Repeated Unit in a

Fuel Cell Stack Reference: LE-46 .
2.2.3.2.3 Fuel Cell Plant Description

As shown in Figure 2.16, the fuel cell combines hydrogen produced from
the fuel and oxygen from the air to produce DC power, water, and heat. In
cases where CO and CH4 are reacted in the cell to produce hydrogen, CO2 is
also a product. These reactions must be carried out at a suitable temperature
and pressure for fuel cell operation. A system must be built around the fuel
cells to supply air and clean fuel, convert the power to a more usable form
such as grid quality ac power, and remove the depleted reactants and heat
that are produced by the reactions in the cells. Figure 2.19 below shows a
simple rendition of a fuel cell power plant. Beginning with fuel processing, a
conventional fuel (natural gas, other gaseous hydrocarbons, methanol,
naphtha, or coal) is cleaned, then converted into a gas containing hydrogen.
Energy conversion occurs when dc electricity is generated by means of
61
individual fuel cells combined in stacks or bundles. A varying number of
cells or stacks can be matched to a particular power application. Finally,
power conditioning converts the electric power from dc into regulated dc or
ac for consumer use. Section 9.1 describes the processes of a fuel cell power
plant system.
Figure 2.19/ Fuel Cell Power Plant Major Processes
2.2.3.2.4 Applications
One of the characteristics of fuel cell systems is that their efficiency is nearly
unaffected by size. This means that small, relatively high efficient power
plants can be developed, thus avoiding the higher cost exposure associated
with large plant development. As a result, initial stationary plant
development has been focused on several hundred kW to low MW capacity
plants. Smaller plants (several hundred kW to 1 to 2 MW) can be sited at the
user’s facility and are suited for cogeneration operation, that is, the plants
produce electricity and thermal energy. Larger, dispersed plants (1 to 10
MW) are likely to be used for distributed generation. The plants are fuelled
primarily with natural gas. Once these plants are commercialized and price
improvements materialize, fuel cells will be considered for large base-load
plants because of their high efficiency. The base-load plants could be fuelled
by natural gas or coal. The fuel product from a coal gasifier, once cleaned, is
compatible for use with fuel cells. Systems integration studies show that
high temperature fuel cells closely match coal gasifier operation.
Some positive characteristics that fuel cells and fuel cell plants offer are:
• Direct energy conversion (no combustion),

• No moving parts in the energy converter,
• Quiet operation,
• Demonstrated high availability of lower temperature units,
• Sitting ability,
• Fuel flexibility,
• Demonstrated endurance/reliability of lower temperature units,
• Good performance at off-design load operation,
• Modular installations to match load and increase reliability,
62
• Remote/unattended operation,
• Size flexibility,
• Rapid load following capability.
General negative features of fuel cells include:

• Market entry cost high; Nth cost goals not demonstrated,
• Unfamiliar technology to the power industry,
• No infrastructure.
2.2.3.3. Hydrogen Storage, High Pressure Storage Tanks

If the greatest challenge in hydrogen use is to extract it, the second greatest
challenge is how to store it. Hydrogen has the lowest gas density and the
second-lowest boiling point of all known substances, making it a challenge
to store as either a gas or a liquid. As a gas, it requires very large storage
volumes and pressures. As a liquid, it requires a cryogenic storage system.
Hydrogen’s low density, both as a gas and a liquid, also results in very low
energy density. Stated otherwise, a given volume of hydrogen contains less
energy than the same volume of other fuels. This also increases the relative
storage tank size, as more hydrogen is required to meet a given vehicle’s
range requirements.
The amount of hydrogen needed for fuel cells is offset somewhat by
the fact that it is used more efficiently than when burned in an internal
combustion engine, so less fuel is required to achieve the same result.
Despite its low volumetric energy density, hydrogen has the highest energy-
to-weight ratio of any fuel. Unfortunately, this weight advantage is usually
overshadowed by the high weight of the hydrogen storage tanks and
associated equipment. Thus, most hydrogen storage systems are
considerably bulkier and/or heavier than those used for gasoline or diesel
fuels. For all practical purposes, hydrogen can be stored as either a high-
pressure gas, a liquid in cryogenic containers, or a gas chemically bound to
certain metals (hydrides).
High-Pressure Gas Storage

One of the most practical of the methods of storing hydrogen is to simply
compress it as a gas. This increases its density. The major concerns are the
large volume required to store the gas even when compressed, and the
ability of the container to resist impact. Storage conditions are set at 3600psi
or 248bar (standard for natural gas cylinders) at ambient temperature (300
K). The amount of work required to compress the hydrogen gas into the
cylinder means that there is an energy penalty of approximately 5-10%. The
temperature increases when the hydrogen cylinder is filled with compressed
hydrogen, and the pressure is higher than the nominal operating pressure
until the cylinder has a chance to cool; care must be taken not to over-
pressurize the cylinder. The decrease in temperature during usage due to
63
expansion of hydrogen is not as great a concern, because the release rate is
much slower. Current hydrogen gas storage containers are made from steel
alloys that are resistant to hydrogen embrittlement; more advanced cylinders
made from aluminium and wrapped with carbon fibre laminate for stiffness
are lighter and currently used to contain both natural gas and hydrogen. Less
well developed are fully-composite cylinders made solely from carbon fibre
impregnated with resin or some other binder; these can have hydrogen
gravimetric densities of as much as 9.5% due to their light weight. However,
they are more fragile and currently expensive. Cylinder manufacturers strive
to attain the highest storage pressures possible in order to reduce the
required storage volume. High-pressure cylinders typically store hydrogen at
up to 3600psi (250bar) although new designs have been certified for 5000
psig (350bar) operation.
Liquid Storage
Liquid hydrogen storage systems overcome many of the weight and size
problems associated with Liquid hydrogen can be stored just below its
normal boiling point of –424 ºF (–253 ºC; 20 K) at or close to ambient pres-
sure in a double-walled, super-insulating tank (or “dewar”). Hydrogen
cannot be stored in liquid form indefinitely. All tanks, no matter how good
the insulation, allow some heat to transfer from the ambient surroundings.
The heat leakage rate depends on the design and size of tank- in this case,
bigger is better. This heat causes some of the hydrogen to vaporize and the
tank pressure to increase. Stationary liquid hydrogen storage tanks are often
spherical since this shape offers the smallest surface area for a given volume,
and therefore presents the smallest heat transfer area. Tanks have a
maximum overpressure capacity of about 72 psi (5 bar); if the hydrogen is
not consumed as quickly as it vaporizes, the pressure builds to a point where
it vents through a pressure relief valve. Liquid hydrogen is considerably
denser than gaseous hydrogen but is still much more bulky than gasoline on
an equivalent energy basis. Liquid hydrogen storage systems can be four to
ten times larger and heavier than an equivalent gasoline tank. Hydrogen
liquefaction is a very energy intensive process due to the extremely low
temperatures involved. Liquefaction involves several steps, including:
1. Compression of hydrogen gas using reciprocating compressors; pre-

cooling of the compressed gas to liquid nitrogen temperatures –319
ºF (–195 ºC; 78 K),
2. Expansion through turbines,
3. Catalytic conversion to its stable “parahydrogen” form.
Metal Hydrides
Metal hydride storage systems are based on the principle that some metals
readily absorb gaseous hydrogen under conditions of high pressure and
64
moderate temperature to form metal hydrides. These metal hydrides release
the hydrogen gas when heated at low pressure and relatively high
temperature. In essence, the metals soak up and release hydrogen like a
sponge.
The advantages of metal hydride storage systems revolve around the
fact that the hydrogen becomes part of the chemical structure of the metal
itself and therefore does not require high pressures or cryogenic
temperatures for operation. Since hydrogen is released from the hydride for
use at low pressure (and must be released before it can burn rap-idly),
hydrides are the most intrinsically safe of all methods of storing hydrogen.
There are many types of specific metal hydrides, but they are primarily based
on metal alloys of magnesium, nickel, iron and titanium. In general, metal
hydrides can be divided into those with a low or high hydrogen desorption
(release) temperature. The high temperature hydrides may be less expensive
and hold more hydrogen than the low temperature hydrides, but require
significant amounts of heat in order to release the hydrogen. Low
temperature hydrides can get sufficient heat from an engine, but high
temperature hydrides require an external source of heat. The low desorption
temperatures associated with some hydrides can be a problem since the gas
releases too readily at ambient conditions. To overcome this, low
temperature hydrides need to be pressurized, increasing the complexity of
the process.
The main disadvantage of metal hydride storage systems is not so
much the temperatures and pressures needed to release the hydrogen, but
rather their low mass energy density. Even the best metal hydrides contain
only 8% hydrogen by weight and therefore tend to be very heavy and
expensive. Metal hydride storage systems can be up to 30 times heavier and
ten times larger than a gasoline tank with the same energy content. Another
disadvantage of metal hydride storage systems is that they must be charged
with only very pure hydrogen or they become contaminated with a
corresponding loss of capacity. Oxygen and water are prime culprits as they
chemically adsorb onto the metal surface displacing potential hydrogen
bonds. The storage capacity lost through contamination can to some extent
be reactivated with heat.
65
End of Chapte r 2
66
Chapter 3-Methodology
The backbone of this study is unambiguously the theoretical and practical analysis. To perform the D-SM
technique with MERIT it is necessary to define an appropriate climatic model and then appropriate ReST to
sustain the D-SM simulation for the Eco-Village. There are a lot of numerical calculations involved with the
selection of a sound FC plant as well as technical digestion about it that had to be examined simultaneously to
allow the best potential choice; the same applies for the investigation about ReST.
3.1 Selection of Climatic Profile

The first essential step into performing a computer simulation, with the aid
of MERIT©, is to satisfy the boundary conditions of the simulation. In this
case the software required three sets of boundary conditions namely the
“Specify Analysis conditions”, the “Specify Demand” and the “Specify Supply”
components. It is impossible to move on to the simulation without
determining these three conditional clusters. It is also impossible, as an act
of guidance and denotation to the user, to determine either the demand or
the supply conditions without having firstly defined the analysis conditions.
This electronic mechanism is assigned to process the introduction of a set of
weather data, from a geographic area of interest, in a predefined form of
files that the rest of the program can identify. These files are called “.clm”
files and some are built in to the available version of the software to provide
a sufficient help and reference to the beginner for simulations of elementary
basis. For the more experienced and stern user there is another component,
into the program’s framework, that allows the electronic conversion of a
given (again in a pre-specified type) file to the one mentioned above to
establish a more customised simulation. This file is usually a “.csv” file that
can be created from a Microsoft Excel© interface to the required
configuration. The following methodology is referring to gathering and
manipulation of raw weather data into the formation of the required “.clm”
file for MERIT.
3.1.1 Data Acquisition

Geographically the eco-village is located at the Thornylee Forest, which
belongs to the Peeblesshire County of south Scotland as we saw in P.2.1.3
and it is close to the town Innerleithen (See Figure 3.1). Any weather station,
chosen for an appropriate set of weather variables, should therefore be
around Thornylee Forest so that realistic values of a weather profile could
be retrieved. It must be clear at this point that since the beginning of the
project it was decided that a radius-to-centre approach must be followed,
with the centre always being the Thornylee Forest (C), so that the Aim II of
the project, about a pragmatic collection of weather information, was
satisfied to offer a considerable realisation of the weather effect on the
study.
67
Figure 3.1/ Area around Thornylee Forest
At the beginning of the project there were three possible weather

databases that were examined for there potential use. These were:
• “The UK Environmental Change Network or ECN” Reference: IS-7,

• “The British Atmospheric Data Centre or BADC” Reference: IS-8 and
• “EnergyPlus Weather Data - International Locations” Reference: IS-9 by the
Office of Building Technology, State and Community
Programs in USA.
From these three possible database candidates only one could prove
sufficient enough to be accepted as the project’s Principal Weather Database
(PWD). To start with ECN the first site that was of immediate interest was
the River site at river Tweed (Galafoot- Number 16 in Figure 3.2) since it is
very close to the Thornylee Forest, approximately 14km (R1) according to
the radius-to-centre requirement that we mentioned above. Contact was
made with this service and upon receiving an e-mail from them it was
specified that site could only provide freshwater indicators as this site truly
was a Freshwater site. The closest suggested terrestrial site for the
meteorological indicators that we were looking for was Sourhope (Figure
3.2), approximately 50km (R2) from (C).
68
Figure 3.2/ Observation Stations for ECN Database
Chronologically, at this point BADC had approved the access to the

their databases supported by the Met Office Reference:IS-10 of UK and all the
necessary data that we required could be equally and adequately found from
this organisation and so the weather data search by ECN was terminated.
The last candidate was also rejected as the sites of meteorological
observations were too far away from our target area (C). In the USA there is
a governmental department about energy issues. This department has a body
about renewable energy applications and utilizations, namely the Office of
Energy Efficiency and Renewable Energy, which has a division about
building efficiency optimization, namely The Office of Building Technology,
State and Community Programs. The latter has supported the development
of a variety of building energy software tools one if which is the
EnergyPlus©. This software has a weather database of national and
international character and it is this database that we examined for
adaptation. Amongst the UK databases that the software uses there were
three that represented Scotland i.e. Aberdeen, Leuchars, and Oban with radii
R3=97km, R4=46km and R5=200km respectively, all of which are
forbiddingly too large for our condition. Thus the nature of this database
69
was also inadaptable and was turned down. This left us with the BADC
database which we will present here.
BADC allowed access to the Land Surface Observation restricted
database after the completion of a form on behalf of the author, the data
coming from the Met Office. In effect these data are daily measurements
form a long-term record of historical weather conditions. There are also
hourly measurements, which were more attractive to this project, allowing
the analysis of current weather systems with hourly resolution.
The daily data are available from UK stations in 110 UK counties over the
period 1853 to July 2000. The hourly data are available from stations in 110
UK counties from 1983 to July 2000.
3.1.2 Interpretation
The BADC database is categorised by two main sections: the “Data
Availability” and the “File Format”. Both of these sections had to be
examined for their relative coupling with this project’s objectives. For the
“Data Availability” we required a continuous and as far as possible a
complete concatenation of data with a focus on the years between 1990-
nowdays, since the study refers to a modern design. For the “File Format” of
the data we had to choose amongst those with the most germane character
to those parameters that would fortify the simulation.
Availability is differentiated according to a 24h or a 1h-basis data
measurements, that being the first step in identifying their potential
exploitation. So within the internet site of BADC we can find the “UK daily
observations (1853-July 2000), in 110 UK counties” and the “UK Synoptic (hourly)
Stations (1983-July 2000), in 110 UK counties” sectioned databases for the
British Isles (there is also a third one but it was of no important value to us).
MERIT can recognise a certain type of weather files in which the weather
profiles are described by six fields on a 1h-basis (see P.3.1.4) on 24h/daily
cycles. This requirement clearly guided us to choose the “UK Synoptic (hourly)
Stations (1983-July 2000)” database. The File Formats in this database are
shown in the table below Table 3.1. These formats have many other sorting
parameters that the user needs to know in order to effectively select the
correct data for his/her study. That information is provided in Tables 3.2
and 3.3. In these tables the .hsun file type is not included for description
since the study could sufficiently be integrated by the other three data
formats. The Sorting Number column refers to a personal identification of
the Message Type Domain for each one of the three parameters that will be
useful in later stages of the analysis.
70
Table 3.1/ File Formats of the BADC database
File Format
Data Sorting Name Description
(Type)
UK Hourly Weather Weather observations file format
.hwx
Observations data
UK Hourly Solar Radiation

.radt Radiation file format
data
Hourly sunshine observations file

UK Hourly Sun data .hsun format
UK Wind data .wind Wind data file format
Table 3.2 /Sorting Parameters

File Sorting Message Type Description (by ID Type Comments
Format Number Domain (in BADC)
(Type) BADC)
.hwx {1} SYNOP Elements from full FM WMO Hourly synoptic
12-VII SYNOP observation
message - WMO received in
Standard Synoptic SYNOP report
report - Hourly
.hwx {2} AWSHRLY ? DCNN Hourly synoptic
observations
received from
Climate Data
Loggers (CDLs)
.hwx {3} METAR ? ICAO Half-hourly
synoptic
observation
received in
METAR report
from station in
aviation
network
.hwx {4} DLY3208 Elements from DCNN Daily synoptic
Metform 3208 - report at 0900
Monthly Return of or other hour
Daily Obs. from an
Ordinary
Climatological
Station
.radt {5} DRADR35 MetO1 Form R35 DCNN Daily radiation
elements - Daily Totals from Form R35
of Radiation/Sunshine
.radt {6} MODLERAD Hourly radiation values DCNN Hourly radiation
from MODLE (Met from MODLE
Office Data Logging
Equipment)
.radt {7} ESAWRADT Hourly radiation values DCNN Hourly radiation
from ESAWS from automatic
(Enhanced Synoptic stations
AWS)
71
.radt {8} AWSHRLY ? DCNN Hourly radiation
from CDLs
.wind {9} HWND6910 Elements from WIND Mean hourly
Metform 6910 - wind and gust
Analysis of from analysis of
Anemograms anemograph
record reported
on Form 6910
.wind {10} HWNDAUTO Elements from WIND Mean hourly
automatic wind wind and gust
recording devices from Digital
Anemograph
Logging
Equipment
(DALE)
.wind {13} ESAWWIND Mean hourly wind WIND Mean hourly
observations from wind and gust
ESAWS (Enhanced from automatic
Synoptic AWS) station
.wind {12} DLY3208 Elements from DCNN 24 hour run of
Metform 3208 - wind from an
Monthly Return of Ordinary
Daily Obs Climatological
Station
.wind {11} AWSHRLY ? WIND Hourly mean
wind from
CDLs
Table 3.3/ Explanation of ID Type

ID Type Description (by BADC)
Synoptic stations selected as suitable for possible

international exchange are give a 5-figure WMO
number which is used as the identifier for all
SYNOP and SREW reports. It is also used as
identifier for climate reports, NCM and HCM,
WMO
exchanged within the UK in real time. The first 2
figures of the WMO number are 03 which is the
block number for the UK and Ireland. Numbering
runs from north to south across Britain followed
by Ireland.
All stations that are part of the climate network

have a 4-figure DCNN (district county number). In
general, if a station moves more than 800m in a
region of homogeneous terrain it is allocated a new
DCNN
DCNN, while a lesser distance will justify a new
DCNN only if it is considered that the exposure at
the new site is sufficiently different to affect the
measured climatology.
72
Stations that are part of the aviation network have a
ICAO 4-character international ICAO number. The first
two characters are EG which represent Europe-
UK.
Like rainfall number the wind number identifies the

characteristics of the observing site. Each
anemometer mast has a 6-figure wind number of
the format DCNNnn, where nn=01, 02… is the
WIND
anemometer site number. A new site number is
allocated to the observations if the mast is
repositioned but not if the height of the
anemometer on the mast is changed. A station may
therefore be associated with several wind numbers
Each one of the file formats is recording a number of parameters. Some of

these are not important at all whereas others are the essential data that we
were looking for. Table 3.4 shows these parameters for each one of the
three formats with the corresponding headers as there are presented at the
BADC databases.
Table 3.4/ File Formats explanation

File Header Parameter Units Comments (by BADC)
Format
HOUR Hour - Hour of observation from 0 to 2300
10 minutes
DIR wind Degree true From 0 to 360 degrees, clockwise.
direction
Horizontal wind is a 2-dimensional
vector and is usually reported as an
averaged direction from which the wind
is blowing and a speed. The maximum
10 minutes
SPEED Knots observed speed over a specified time
wind speed
interval and the time of occurrence may
also be reported. The unit of speed used
at UK stations is the knot (0.515 ms-1)
and the unit of direction the degree.
.hwx Temperature was recorded in degrees
Fahrenheit before 1961 and in degrees
Celsius after that date. The precision of
Dry-bulb air 0.1 Degrees
TEMP the measurement in the meteorological
temperature Celcius
report has varied over the years:
• 0.1C for all temperatures that are
reported today
The dew point temperature (in degrees
Celsius) is the temperature to which the
Dew-point 0.1 Degrees
DEW air must be cooled to produce saturation
temperature Celcius
with respect to water at its existing
atmospheric pressure and humidity.
Wet-bulb 0.1 Degrees The web-bulb temperature is the lowest
WETB
temperature Celcius temperature (in degrees Celsius) that can
73
be obtained by evaporating water into the
air. It measures the humidity of the air.
See Met Office documentation
END_HOUR Hour - Hour of observation from 0 to 2300
Global Solar 'Global' radiation is that received from
GLOBAL irradiation W.hour/sq.m both the sun and the surrounding
amount environment
.radt Diffuse Solar 'Diffuse' radiation is that obtained when a
DIFFUSE irradiation W.hour/sq.m shade ring is used to block out the sun's
amount direct radiation.
Direct Solar Global radiation is the amount of Direct
DIRECT irradiation W.hour/sq.m and Diffuse radiation which reaches the
amount Earth's surface at a given location.
END_HOUR Hour - Hour of observation from 0 to 2300
The wind direction from which the wind
Mean Wind blows is measured in Degrees (true). The
MDIR degree true
Direction entry for an east wind is 090 that for a
south wind 180 and so on clockwise.
Horizontal wind is a 2-dimensional
.wind vector and is usually reported as an
averaged direction from which the wind
is blowing and a speed. The maximum
Mean Wind
MSPEED Knots observed speed over a specified time
Speed
interval and the time of occurrence may
also be reported. The unit of speed used
at UK stations is the knot (0.515 ms-1)
and the unit of direction the degree.
3.1.3 Validation
The three data formats that we presented before are the essential part of the
search in need for climatic information. Soon it was realised that the best
way to check the weather stations for these data sets was geographically.
BADC has divided the UK into counties every one of which has a number
of weather stations Figure 3.3. Thornylee Forest is in Peeblesshire County
so the hunt started from examining the stations in this county for the
variables of interest. A record of the stations reviewed was kept and can be
seen in Table 1 in Appendix A. From 27 stations investigated only 1 was of
relative interest - Glentress. The file format of the weather data for this
station was of .hwx type, an apparently convenient file until further
examination described later in this chapter (see P.3.1.4) cast it insufficient
for a potential simulation file. This was not obviously the case for a sound
file construction leaving the author to expand the search [Delimitation
Plan-A] from the area of interest (Peeblesshire County) to the neighbouring
counties namely Selkirkshire, Dumfriesshire, Lanarkshire and Midlothian (in
Borders and in Lothian Region) and Berwickshire, following a clockwise
route from Selkirkshire to Berwickshire (See Figure 3.3). Any other counties
apart from the surrounding counties would associate a too large an area for
a pragmatic simulation of wind and radiation configurations. Thus at the
vicinity of Peeblesshire we searched 28, 71, 109, 1, 94 and 43 stations
74
respectively for the counties mentioned above, thought this time only a
specific record was kept for the vast number of the stations reviewed which
corresponds to those stations with .hwx, .radt, .wind weather attributes. The
latter can be seen in Table 2 in Appendix A.
Figure 3.3/ UK Counties
Of course even with 29 stations the choice of selecting the proper ones for
our case needed to be cut down to the very important so that a sincere
evaluation could follow to leave us with a sound set of weather data. So we
had to think of a number of criteria to refine those numbers. These were:
1. No station should be left out of the volition if it contains a .radt file.

The thought was that since out of 29 stations only 3 had the required
radiation files they should be chosen for the next phase.
2. Any station with three weather fields (.hwx, .radt and .wind) should be
included in the next phase. Since wind and radiation are both required
for the simulation a station with both of these data is valid source of
the climatic configuration of the area and so it should be selected
appropriately.
3. All stations with wind data should be selected unless their relative
distance from the (C) point is too big (more than R*=48.3Km) or it
contains a radiation file.
75
These criteria once applied to the 29 stations revealed the possible station
selection for getting the appropriate weather data. The summary of the
remained stations can be seen in Table 3.5 below.
Table 3.5 / Selected Stations for Delimitation Plan-A

Sorting Number (s) Association
Station County
Number
.hwx .radt .wind
GLENTRESS PEEBLESHIRE {4} x x W1
BOWHILL SELKIRKSHIRE {4} x {11} W3
GALASHIELS SELKIRKSHIRE {4} x x W2
ESKDALEMUIR DUMFRIESSHIRE {1} {5},{6} {9},{10} Rad1
CARNWATH LANARKSHIRE {4} x {11} W4
ABINGTON LANARKSHIRE {4} x {11} W5
DRUMALBIN
LANARKSHIRE {1} {5},{6},{7} {9},{13} Rad2
SAWS
CAMPS
LANARKSHIRE {4} x x W6
RESERVOIR
MIDLOTHIAN IN
BUSH HOUSE LOTHIAN {4} x x W7
MIDLOTHIAN IN
PENICUIK LOTHIAN {4} x x W8
CHARTERHALL
BERWICKSHIRE x {5},{7} x Rad3
SAWS
At Table 3.5 we can observe the occurrence of two or three Sorting

Numbers (SN) for a parameter, which is just a characteristic of that specific
database containing a variety of weather data of similar type. The last stage
in this section is a validity check for the weather parameter file types that
will allow us to qualify the number of weather data into working values for
the evaluation stage. The validity check will be used insofar as a simple basis
of recognising the particular points of each parameter on an arbitrary
measurement scale. From the BADC site we were able to access any
“Message Type Domains” for any of the three “File Formats” to discover that
there were disparities in the absolute measurement of the parameters
addressing time intervals; something that we mentioned before in Table 3.2.
So under the requirement of “a 1h-basis measurement steps on 24h/daily repeating
cycles” climatic measurements a favouring should be submitted to these
Domains that obey that prerequisite. Table 3.6 shows the validity check for
the 13 Domains of the databases grouped under sections of “File Formats”.
76
Table 3.6/ Validity check for the 13 Domains
Ranking
Domain Format Sorting Number Ordinance
(points)
SYNOP {1} {1} > {4}.
AWSHRLY {2} For {2}, {3}
.hwx there is no
METAR {3} 2>1
accessible
configuration to
DLY3208 {4} validate
DRADR35 {5} {6}, {7} > {5}.
MODLERAD .radt {6} For {8} there is
no accessible 2>1
ESAWRADT {7} configuration to
AWSHRLY {8} validate.
HWND6910 {9} {10} , {13} > {9}
HWNDAUTO {10} >{10}
.wind For {12} there is
ESAWWIND {11} 3>2>1
no accessible
DLY3208 {12} configuration to
AWSHRLY {13} validate.
With this information in hand we could then proceed to the next stage of
the weather station selection with an extended evaluation of these stations
under the specific criteria for a rectified profile (see P.3.1.5).
3.1.4 Evaluation
The 11 stations that were validated for the objectives of the project in the
last section (Table 3.5) had to be evaluated in a two-gear process that will
allow the selection of correct values of wind and radiation parameters. The
first gear mechanism is to leave out those with low scores and the second to
identify which ones of the high score group would be the most effective for
utilisation (profile for simulation).
The first gear mechanism was conceived to ensure that any station,
chosen for the next level, would have the necessary parametrical format and
quality of information with the one that MERIT operates so that we could
put together an effective profile for a sound simulation. The stations were
evaluated for:
1. Qualitative Parametrical Potential or QPA (where parameters are

hourly measurements for wind, radiation and temperature attributes)
based on the Ordinance values as taken from Table 3.6.
2. Availability of Data; in years.
3. Distance from the area of interest (Thornylee Forest); a personal
scaling relative to the position of the station on the map.
The evaluation is presented in Table 3.7 below.
77
Table 3.7 - Comments:
• The Sorting Number for the File Formats can be found in Table 3.5.
• The scoring is in simple arithmetic points –no units are involved.
• Total score is a simple arithmetic addition.
• The Distance scoring is conversely proportional to the distance of the
station from (C) i.e. the closest the station to (C) the highest the
points it will score. Distances can be seen in Figure 3.4.
• Association Numbers are descriptive of the potential application of
the stations for the nature of information that they can provide i.e. W
for wind and R for solar radiation variables.
Table 3.7/ Stations Evaluation

Station Name QPA Availability Distance Total Association
Score Number
.hwx .radt .wind .hwx .radt .wind
GLENTRESS 1 0 0 83/ - - 5 6 W1
97
BOWHILL 1 0 1 83/ - 89 4 6 W3
99
GALASHIELS 1 0 0 83/ - - 4 5 W2
99
ESKDALEMUIR 2 2 3 83/ 71/ 84/ 1 8 R1
00 00 94
CARNWATH 1 0 1 83/ - 83/ 2 4 W4
99 86
ABINGTON 1 0 1 83/ - 83/ 2 4 W5
94 94
DRUMALBIN 2 2 3 91/ 91/ 97/ 1 8 R2
SAWS 00 00 00
CAMPS 1 0 0 83/ - - 2 3 W6
RESERVOIR 99
BUSH HOUSE 1 0 0 83/ - - 2 3 W7
99
PENICUIK 1 0 0 83/ 94/ - 3 4 W8
99 00
CHARTERHALL 0 2 0 - - - 1 3 R3
SAWS
78
Figure 3.4/ 11 Stations from C (Thornylee Forest)
For reasons explained in P.4.1.1 as part of a stretched Evaluation phase we

performed an extended search in the surrounding counties (Delimitation
Plan-B) on look for a valid station that could provide a .radt file for I d and
I n values. This plan included the following counties of interest:
Roxburghshire, Cumberland, Kirkcudbrightshire, Ayrshire, Renfrewshire,
Dumbarton, Stirlingshire, Clackmannanshire, Kinross Shire, West Lothian,
East Lothian, Fife, Northumberland, , and Durham. Unfortunately none of
these counties had a station with .radt files and so stretched Evaluation
phase was terminated, never concluded, to adopt the solution given in
P.4.1.1.
As part of the second gear mechanism the two highest score stations
were to be assessed for their relative potential to provide the necessary wind
data. To do such an assessment we had to devise a Consecutive Elimination
Assessment and Comparison Plan (CEACP) which was completed within 4
steps. Description of Steps 1-3 analysis can be found in Table 3.8 and that
for Step 4 in Tables 3 and 4 in Appendix A. In Step 1 the relative distance
of R1 and R2 from Thornylee forest was to be considered (See Figure 3.4).
In Step 2, according to the conditions of assumption A3 (See P.4.1.1.2), we
had to compare the elevation of the areas of the stations with that of the
Thornylee forest. In Step 3 (elimination step), for the same reason as in
previous step, we had to compare the divergence of the annual values for
average wind speed velocity of the areas of the stations with that of the
Thornylee Forest. Finally in Step 4, again according to the conditions of
assumption A3, the CEACP was concluded by comparison of two seasonal
weather profiles for two random years concerning Eskdalemuir and Bowhill
stations. For the most possible experimental success the weather profiles
were a robust hybrid of seasonal observations (4 representative months for
each season divided in 7 monthly segments - in 5 consecutive day steps- at
9:00am measurements) and 5 critical weather parameters (wind direction,
79
wind speed, total cloud amount, visibility and temperature). We wish the
databases could give us more recordings for more parameters but that was
not true – incomplete files.
Table 3.8 - Comments:

• The annual mean wind speed is retrieved by the relative map of the
BWEA Reference: IS-11shown in Figure 3.6.
• Obviously Bowhill (See Figure 3.4) is nowhere close to Thornylee
Forest but it is the only station within a reasonable distance
RB =8.85Km from that area and more importantly it is the only
station with a respectable type of wind observations, Domain :{ 11},
for an R<10Km. The latter is also the only station within the
R<10Km condition that has a complete data range for the years of
examination. All of these stations belong to a homogeneous
geographical region (as assumption A3 states), see Figure 3.5.
Table 3.8/ 3 steps of CEACP

Step 1 Step 2 Step 3
Elevation (from sea Distance Annual Mean Wind
level) Speed
ESKDALEMUIR 242m RE =45.5Km 7-8 m/s
DRUMALBIN SAWS 245m RDS =45.2Km 5-6 m/s
Thornylee Forest 144m 0 10 m/s
As we can see from P.4.1.1.2 after completing CEACP the choice of using
Eskdalemuir for wind data was justified sufficiently from the findings and so
the last phase of the Climate Selection was to be completed with the
creation of the proper climatic file for MERIT to sustain the simulation.
Figure 3.5/ Geographical Similarities of the areas of the two stations

(Eskdalemuir and Drumalbin Saws)
80
Figure 3.6/ annual mean wind speed for UK Reference: IS-11.
3.1.5 Formation
A retrospection of the previous phases of Climate Selection is leaving us
with the following points:
1. Out of 11 qualifying stations, chosen for their meteorological

observations of weather behaviour at several places around Thornylee
Forest, only one (Eskdalemuir) was found possible to support the
climate creation for MERIT with partial provision of the necessary
parameters.
2. None of these stations could provide the ReST of the crucial
parameters with information from BADC databases, and so a
discursive file was used from another source that bounded to
assumptions A1 and A2 and was used conditionally to succeed this
goal.
3. The Eskdalemuir station has two Domains of weather files, in the
BADC database, the .synop Domain or {1} and the .hwdnauto Domain or
{10} which will provide hourly measurements of dry bulb air
temperature, dew point temperature and wet bulb temperature for
{1} and mean wind speed and mean wind direction for {10}
respectively. These Domains extend from 1983-2000 for {1} and 1984-
1999 for {10}.
4. The diffuse solar intensity ( I d ) on the horizontal and direct normal
solar intensity ( I n ) values were provided by the discursive file for the
year 1978 at the same area as that of Eskdalemuir station.
81
5. The .clm file that MERIT requires for the simulation it must be
constructed by a .csv Excel file which with help of file conversion
software (component of MERIT) will change into the right form.
These are the key issues so far. To build the .csv Excel file we need to know
some things about MERIT and the way it uses external weather information
into a structured .clm file. This file requires 6 fields, arranged in columns on
a 1h-step daily cycles. These fields are:
a) Diffuse solar intensity on the horizontal (W/m2)

b) External dry bulb temperature (Tenths of Degrees C)
c) Direct normal solar intensity (W/m2)
d) Prevailing wind speed (Tenths m/s)
e) Wind direction (Clockwise degrees from north)
f) Relative humidity (%)
The purpose of this paragraph is to explain the process followed to turn the
Eskdalemuir station values into the formats explained above and then
produce the .csv file for MERIT conversion. The first thing we had to
examine was to find out which one of the .hwdnauto and .synop yearly
combinations of Eskdalemuir’s Domains was appropriate for later stages of
climatic creation according to a yearly validity check for a time scale of ten
years. Since the project requires a realistic simulation a ten years span was
chosen as representing the last decade of the past century i.e. 1990-1999.
The validity check was accurate for .synop files but with .hwdnauto there where
many data inconsistencies that could prove fatal in the .csv file construction.
The check was attributed to the fact that since one complete year with
measurements about a weather parameter on a 1h-step daily cycles (e.g. one
daily cycle from 00:00h to 00:00h would have 24 hits for a 1h-step
measurements) would give 8760 hits (24*365). The two years marked out
for their completeness in data hits for both of the two Domains are presented
in Table 3.9 below. It is obvious that a clear selection can be made for which
year should we use, according to the maximum number of hits of .hwdnauto
files; 1997 was that year.
When it was clear of which year was available with the more complete
file data we had to bring them into the right form, the one that MERIT
requires. Initially an Excel file (Eskdalemuir97DM.xls) was used to make all
the necessary modifications to the texture and the numeric aspects of the
raw data, from the .hwdnauto and .synop Domain files of the 1997 year, and
then the conversion of the Excel file was attempted into a .csv and then into
a .clm file. By changes in texture we mean the process of altering the raw
data into the right configuration that MERIT requires, that is including
magnitude and units.
82
Table 3.9/ Completeness in data for the two Domains
Domain BADC hits Theoretical hits for 1 year
1997
.hwdnauto 8655 8760
.synop 8760 8760
1998
.hwdnauto 8634 8760
.synop 8760 8760
From the beginning of the paragraph we stated that the .hwdnauto Domain
will provide hourly measurements of dry bulb air temperature, dew point
temperature and wet bulb temperature whereas .synop Domain is responsible
for mean wind speed and mean wind direction measurements. Some of
these parameters can be used without changes for the 6 fields of the .clm file
but some others do require one or many-sided changes for the shaping of
fields. All the changes can be seen in Table 3.10 below. At this table we also
present the two parameters of I d and I n , vital for the complete image of the
configuration.
Table 3.10/ Modifications in Data nature

Change in Field Shaped for
Domain Parameters Change in Units
Magnitude MERIT
Not required –
Dry bulb air External dry bulb
Not required already in tenths of
temperature temperature
degrees C
.hwdnauto Dew point
temperature Relative humidity
Not required Relative humidity
Wet bulb (%)
temperature
Data in Knots –
Not required
change them to Prevailing wind
Mean wind speed
m/s. speed
(1Knot=0.514m/s)
.synop
Not required –
Mean wind already in
Not required Wind direction
direction clockwise degrees
from north
Diffuse solar Diffuse solar
? intensity on the Not required Not required intensity on the
horizontal horizontal
Direct normal Direct normal
? Not required Not required
solar intensity solar intensity
Apart from any modifications made in the texture of the raw data, we also
had to make some numerical modifications at them namely the make up of
105 hits shortage that the .hwdnauto file was found to possess (Table 3.9). At
this point we simply capped the gaps with values from the neighbouring
values after we produced an average for them.
83
When the Eskdalemuir97DM.xls file was prepared we combined it
with Eskdalemuir1978.xls to make the Eskdalemuir1997Final.xls file which was
the cornerstone for the creation of the Eskdalemuir1997Final.csv file the file
to be converted into the .clm file that we required. Eskdalemuir97DM.xls was
checked for invalid values (999), that might they would have carried
forwardly from BADC database, and it was tested against
Eskdalemuir1978.xls for calendar and arithmetic data inconsistency levelling.
When these checks were over and both files were matched the
Eskdalemuir1997Final.xls file was saved as a .csv file and named
Eskdalemuir1997Final.csv. This was then added to the climate folder of the
MERIT (version 2.2) directory and the module CreateClimate.exe of that
software was used to be converted into the right climate file i.e. .clm. Thus
the Esk(97).clm file was created and it was introduced into the climatic
database of MERIT to aid in the realistic simulation of renewable
technologies against the Thornylee Forest’s weather profile for the year
1997. The entries for the CreateClimate.exe module were:
• File Name: Esk(97)

• Latitude: 55.331
• Longitude: -3.205
• Start (Date):1/1/1997
• End (Date): 31/12/1997
• Time Step: 1
3.1.5.1 Final Selection

It is really very sad the fact that this file was never to be used, for reasons
explained in P.4.1.2, a totally incoherent file finally being employed from
MERIT’s database against the one for which this meteorological
methodology was attributed and was to be conducted in a three months
period of time. Still we believe that the methodology followed for this
project can be repeated by other workers for relative studies and so we
decided to presented for educational and guidance reasons.
This time the final selection is a mater of a simple comparison or the
relative radii of the Glasgow and Kew stations for which the climate files
are under consideration. So RG =90Km for Glasgow and RK =570Km
for Kew, the centre of the imaginary circle again being the Thornylee
Forest. It is more than clear that Glasgow station is far more close to the
vexed area of study and so we hope that there will be more similarities in
the weather profiles of these two areas than in the other combination.
Thus the chosen file for the simulation would be Glasgow.clm which was
accepted as the most valid choice from a very narrow set of options
84
3.2 Selection of Power Plant
The energy simulation of match and supply for the Eco-village will be based
on the use of Renewable Supply Technologies (ReST) to provide enough
electrical energy for the power requirements of the 17 houses of that
community. This energy will be provided by Wind Turbines and
Photovoltaic systems, operating as Primary Energy Source (PES) and the
Fuel Cell module which will operate as Secondary Energy Source (SES). The
selection for the PES was through a numerical approach that will be
explained in later stages in this chapter in P.3.3.2.1, though the
corresponding selection for the SES was a mixture of technical and
numerical oriented analysis based on knowledge digestion about Fuel Cell
modules married with the needs of the Eco-Village for a green and efficient
heat and electricity energy system. Since the PES selection is pretty
straightforward we will only present the particular annotations for the
selection of the Fuel Cell module, as this will be proved handy later on, in
the following paragraph.
3.2.1 Technical Orientation for SES Modules

A Fuel Cell plant can be created principally by a hydrogen source, a fuel cell
that will make use of that hydrogen by converting its chemical energy into
electricity and heat and a means of a hydrogen reservoir that will store
hydrogen fuel for use when direct availability is deficient, designated as an
“independent operation” power mode.
3.2.1.1 Electrolyser
The hydrogen source has two most commercially available ways to be
exploited. One way is by connection to a natural gas network, where the H 2
is involved in the chemical bounds of that combination, and the other way
involves the installation of an Electrolyser which will dissociate water into
H 2 and O2 , provided there is a water reservoir and energy to run this
component. The Eco-Village requirement for clean production of energy is
very conditional to allow the first option to be considered. This is oxymoron
as the polluting gases that come by the “burning” of the natural gas are
extremely low Reference: LE-45, compared with those coming from any other fossil
fuel combustion mechanisms, but still there are essentially of considerable
quantities to be allowed our study. Electrolysers have many characteristics
which should be considered for a valid selection of an appropriate module.
Many of them usually have a number of ancillary and accessorial units but in
our case we will only concentrate on the main unit. An internet search was
conducted to find out companies which could give us information about the
electrolyser so to establish a sound validity check and to select a fine model.
Unfortunately not all the companies replied back and at the end only one
85
company was kind enough to offer some information about the model that
it was advertised on the internet. The model that we were looking for had to
employ attributes such as:
& H2
1. Hydrogen generation at a mass flow rate of m ≥ 1.94*103 Kg/s or
a volume flow rate ofVH2
& ≥ 7.87 Nm 3
/h (at base load operating
mode) – see P.3.2.2,
2. Lowest possible energy consumption as a function of m& H 2 and ,
3. Highest possible outlet pressure of gases Pgas at the given m & H 2 ( the
highest the Pgas is the lesser the amount of energy required for
compression of gases for their subsequent pressurisation for the
storage tank)
4. A benign electrolyser, considering fewer possible environmental
hazards,
5. 0-100% range of nominal power capacity,
6. Lowest possible feed-water consumption,
7. High purity of H 2 .
Indeed the electrolyser that we located could satisfy all of the following
attributes so it was conveniently selected for this study. The company
providing the imminent electrolyser was “Vandenborre Technologies N.V.”,
its acclaimed accomplishment being the development of the IMET®
technology which forms the core component of the H2 IGEN® hydrogen
and oxygen generator. The series comprises three models: the 300, 1000 and
2500 with volume flow rate range capacities of 1-3 Nm 3 / h , 3-60 Nm 3 / h and
15-80 Nm 3 / h respectively. Under internal office clarification about the fact
that the three Series have more or less the same attributes except from their
volume flow rate range capacities and in accordance with the biding
requirement for aV&H 2 ≥ 7.87 Nm 3 / h we accepted the H2 IGEN® 1000
Series Electrolyser which proprietary attributes are presented below:
1. Hydrogen generation at a capacity volume flow rate range V&IGEN = 3-

60 Nm 3 / h ,
2. Energy consumption of 5 KWh / Nm3 ,
3. The outlet pressure can be provided at 10 and 25 bar; the requirement
for highest possible outlet pressure guided us to select the model with
Pgas =25bar.
4. The electrolyte is a concentration with 30 % KOH, one of the most
environmentally friendly solutions available Reference: IS-12,
86
5. 0-100% range of nominal power capacity,
6. Feed-water consumption of 1lt/1 Nm3 ,
7. Hydrogen purity of 99.9%.
3.2.1.2 Fuel Cell

In the case of the Fuel Cell we had to decide upon the nature of the fuel cell
and as in the previous case (Electrolyser) to identify a possible model that
would give us technical characteristics for the determination of the other
two modules of the plant. The Fuel Cell would be the hart of the system and
so its study was very thorough on both paper literature and internet-based
information material. Nevertheless it was not possible to discover a
potential model for the requirements of this study and so we had to follow a
theoretical approach to derive its technical characteristics, presented later in
P.3.2.2. Deciding on the nature of the Fuel Cell it was no easy task. As we
have seen in P.2.3.2.1 there many different types of Fuel Cells each with
different characteristics and advantages. We had to identify the most
compatible type of Fuel Cell for the needs of this project and the only way
to achieve that was by establishing a set of features/requirements to look for
in the six types of Fuel Cells for a possible distinction. This set is requiring
for the Fuel Cell to:
1. Have a minimum power output of 25kW at 100% operation capacity

(See later at P.3.3.2.2.1),
2. Utilise hydrogen gas as the principle fuel for the power generation,
3. Have the fast “start-up time” feature and support continuous
operation capability for base load power coverage-“independent
operation” power mode,
4. Acquire a flexible operation power range (15%-100%) for potential
exploitation in different modes for the Eco-Village,
5. Have the capability of providing both heat and electrical power (a
combination known as “cogeneration”),
6. Capacitate the highest possible electrical efficiency,
7. Capacitate the highest possible overall efficiency (including electrical
and thermal exploitation as part of the cogeneration scheme).
After a deep examination of literature it was quite clear that the best
possible choice would be to go along with a Polymer Electrolyte Membrane
(PEM) Fuel Cell for that it would satisfy in the best way the 7
features/requirements as presented above. PEMFC come in many different
plant sizes varying from 500W-100kW (commercial numbers) and more
specifically there are a few companies around (like “Hydrogenics Corp.”
Reference: IS-13
) that produce this medium range of PEMFC at capacities of 5-
25kW which is very close to what we are looking for Reference: IS-14. This power
87
output can be found in other types of fuel cells but the critical requirements
combination for hydrogen fuel at that power output value was only verified
for the PEMFC type. The latter are largely known for their profound ability
to utilise hydrogen as well as hydrocarbons as part of the fuelling system and
there are also known for their fast “start-up time” features Reference: LE-46.
“Independent operation” is possible with PEMFC most of the tests
encountered reporting 4000-9000h problems free operation.
Cogeneration for PEMFC is possible although some conditions should
be applied to the scheme if thermal efficiency is required. In a cogeneration
scheme heat, the by-product of electrical power generation is transferred
from the fuel cell to a heat exchanger. The exchanger transfers the heat to a
water supply, providing hot water to local customers. Since the PEMFC are
based on a low temperature operation basis (80C) it is obvious that the hot
water pipeline network should not very extended, a fact that must be
respected if relatively high temperatures of the working fluid are required-
high enthalpy level. Furthermore PEMFC have good electrical and overall
efficiencies the first reaching 50% and the second being around 70-80%
depending on the materials and the design of the cells stack.
Table 3.11/ PEM Fuel Cell Characteristics.

η El ) ≈ 50% Reference: LE- 47
Electrical Efficiency (
*
V) ≈ 0.8V Reference: LE- 47
Cell Voltage (
Fuel Utilisation ≈ 80% Reference: LE- 47
Operating Temperature 80C
Operating Pressure 1bar
3.2.1.3 Low Pressure Storage Tank

The Storage Tank has the role of supplying hydrogen when the normal
channel i.e. the Electrolyser, for such a task fails. Any imponderable factor
that can affect the normal flow of energy from PES to Electrolyser and can
not be readily accounted for in the designing of the system (a violent storm,
extreme freezing temperatures, a discharging lighting or dead calm days and
any other mechanical, electrical or climatic pouts) must be confronted with
an backup plan so that energy will still flow to the inhabitants of the Eco-
Village and will allow for maintenance and repairing operations. There are
quite a few choices for the storing of H 2 , and as it is expected some of
them require energy input to the H 2 gases to change their thermodynamic
properties whereas other simply take advantage of their special chemical
configuration to accommodate them respectively (P.2.3.3). In today’s
marketing options for H 2 storage the choices will depend on the
application that hydrogen fuel will be provided to. Thus there are mobile
88
applications that require high energy density from the fuel and a lightweight
arrangement of the storage option. For these applications highly compressed
H 2 gas or liquefied H 2 gas cylinders are recommended. Stationary
applications are less demanding in that the weight and size of the container
is not a priority and so in this case we can use a low or high compressed H 2
gas vessel, metal hydrides arrangements and possibly liquid hydrogen
options. The characteristics of an appropriate Storage Tank are:
1. Highest possible working pressure for the hydrogen gases Pstorage ( the
storage pressure is proportional to the size of the vessel dictated by
material and shape limitations),
2. Highest possible nominal capacity of hydrogen gases Cstorage ,
3. Satisfactory Flow Capability ( at least the same, or more than
V&H 2 for the Fuel Cell)
Amongst the companies that we examined the most suitable information-

wise was Chart Industries. Chart’s Bulk Storage Systems comprise a
standard line of pre-engineered tankage (up to 68.2 m 3 ) and custom
engineered storage containers (up to 455 m 3 ) for nitrogen, argon, LNG, and
carbon dioxide for industrial gas customers. These gases have different
properties from hydrogen and so it is not clear if the model that we were to
choose was suitable for this element, and since that point could not be
clarified via e-mail communication we had to make the following
assumption:
A4: “If a pressurised vessel can accommodate nitrogen gas with

atomic weight of 14.0067gr then it can possibly do the same for a gas with a
smaller atomic weight such as 1.00794gr for the same thermodynamic
conditions provided that chemical effects are not important and so only
mechanical phenomena are considered.
A very important issue that our investigation brought up was that there is a
compromise between, Pstorage Cstorage and the size of the tank. In our case we
need the highest possible C storage for an Pstorage equal to Pgas i.e. 25bar. This
is done to avoid any extra energy spent over the pressurisation of hydrogen
gases. Thus the appropriate tank for our case would be from the VS-High
Pressure Bulk Stations Series and more specifically the VS11000NC model.
This has the following characteristics:
1. Pstorage =27.6bar
89
2. Cstorage =192 m 3
&
3. Flow Capability =414 Nm 3 / h > VH2 =7.87 Nm 3 / h that the Fuel Cell
requires.
3.2.2 Numerical G uidelines for SES Modules

The building block of the analysis for the SES Modules is the definition of
the operational characteristics of the Fuel Cell. If we know the hydrogen
fuel consumption for the latter then we can define the Electrolyser and
Storage Tanks sizes.
We start the analysis by calculating the energy requirements of the
Eco-Village. According to the “Tweed Valley Ecovillage Project Overview” Reference:
LE-35
the average use of Electrical Energy ( E El ), in the UK, is for a standard
house is between 3000 and 4000 kWh and around 4000 kWh for Thermal
Energy ( ETh ) for one year. Since the Eco-Village will be situated in an area
where there is no shelter we would expect the thermal requirements to
exceed the thermal value but since the village could also consider the use of
electrical equipment and lighting devises that are less electricity intensive
Reference: IS-15
than the standard house and possibly house designs of passive
solar lighting we would expect the electricity requirements to deceed the
electricity requirements. These trends mutually cancel each other and so we
can choose E El =4000kWh to counterbalance the ETh increased behaviour.
So for the Eco-Village we have:
E E l1 *17= EElV = 68,000kWh, for the Electrical Demand and
ETh1 *17= EThV = 68,000kWh for the Thermal Demand.
Thus the total energy demand for the village, for 1 year will be:
ED =132,000kWh … (Equation 3.1)

So for one day then the energy demand for the village will be:
ED1 = 132,000 =361.64kWh… (Equation 3.2)

365
And the Critical Power that the Fuel Cell is required to distribute to the 17
houses in 24h (one day) will be:
90
*
PD1 = 361.64 =15kW… (Equation 3.3)
24
This Critical Power will drive electrical and thermal loads over 24h so the
independent operation mode, describing a base load configuration, will be fixed
at this value and so will the hydrogen fuel consumption. Later, when we will
have to produce a more realistic demand for the Eco-Village, we will
calculate three different fuel consumptions relative to the three operational
modes that the Fuel Cell will work.
3.2.2.1 Critical Fuel Consump tion for the F C

Having defined the Critical Power we can now proceed into finding what
the Critical Fuel Consumption will be and so sizing the Electrolyser and the
Storage Tank. We start by assuming that all the current that is reaching the
electrolyser is DC that is current from the Wind Turbines and the
Photovoltaic system. That is not the case with Wind Turbines since they
produce AC current, but for simplification of the analysis we accept a
perfect Inverter with efficiency ηInvter =100% (a good commercial
transformer will be around 96-97%) and so none of the power will be lost in
the inversion. Assuming a cell voltage of 0.8V (Table 3.11) and knowing
*
that the power output will be equal to PD1 , we can calculate the sum of all
the cell currents in the stack:
*
P1
I = * D =18,750A… (Equation 3.4)
V
So for the stack:
I 19.53*103
m& H2 = = = 1.94*10−3 Kg/s… (Equation 3.5),
F 96,490,000
Where F is Faraday’s Constant with units of coulombs per mole of

electrons. This value is measured at pressure P=1bar ( ≈ 1atm, 0.1MPa and
14.5psi) and T=80C=353K. With compressible gases, like H 2 , industry uses
standard units of volume flow rate like Nm 3 / h or Nm3 /min at P=1bar and
T=0C. In that way engineers can ensure that every volume measured has the
same amount of product in it i.e. same density. So in our case in order to
keep an industry-oriented approach we will try to convert m& H 2 into a useful
expression that will help us locate the Electrolyser model easier. We will use
the following expression to do that:
P = Z ρ RT … (Equation 3.6)
91
Where,
P: Pressure of the hydrogen gases, here P=0.1 MPa
Z: Compressibility Factor for hydrogen gas relative to the pressure and
temperature of the pressurised volume, here Z=1,
ρ : Density in Kg/ m 3 ,
R: Specific Gas constant for H 2 gas or R=4,128.18 Nm/KgK and
T: Temperature of the gases, here T=353K
Thus we have from (Eq.3.6):

P
ρ= … (Equation 3.7)
ZRT
ρ =0.0686 Kg/ m 3
In standard conditions where P=1atm and T=273K, density of the gases

is:
ρSC =0.0886 Kg/ m 3 … (Equation 3.8)
So between the two densities ρSC and ρ there is a difference of 0.020

Kg/ m 3 . Since this difference is quite small we can use the standard
conditions density to make up an expression for the volume flow rate V&H2
that will be based on common industrial units. From (Eq.3.5) we know that
m& H 2 = 1.94*10−3 Kg/s, so:
& H2
m
V&H 2 = = 2.19*10−3 m3 / s … (Equation 3.9)
ρ SC
Now to achieve the appropriate conversion we use Table 3.12 below:
Table 3.12/ Conversions for Volume flow units

Volume Flow Rate in h @ P=1atm and T=0C
Nm 3 / h Lt/h m3 / h
1 960 0.96
3
Nm / s Lt/s m 3 /s
1 1.037*10 −3 1.0036
Volume Conversions
1 Nm 3 =0.931 m 3
92
So:
V&H2 = 2.18*10− 3 Nm3 / s ,
Or
V&H 2 = 7.87 Nm3 / h … (Equation 3.10)
This is the Critical Fuel Consumption (CFC) for the Fuel Cell. With this in
hand we can now calculate the Critical Number of Storage Tanks (CNST)
(VS11000NC model) for the Eco-Village as well as the Critical Number of
Charging Days (CNCD) that it will take to charge these vessels.
Feed-water Consumption for CFC

The H2 IGEN® 1000 Series Electrolyser has a feed-water consumption of
1lt/1 Nm3 . If the Fuel Cell is to be used for a continuous operation then it
will require an uninterruptible feed-water supply to the Electrolyser equal to
the CFC of the Fuel Cell. So if for an hour the Fuel Cell requires 7.87
Nm 3 / h then for 24h this will be equal to 188.88 Nm 3 and the equivalent
feed-water consumption for the same time interval (1 day) will be equal to
188.88lt or 0.189m3. If this is integrated for the year (365 days) then the
yearly feed-water consumption will be 68,941.2lt or 68.9 m3. These of course
are not a realistic type of numbers since the Electrolyser will be working
more intensively in the real case to cover the demand of the Fuel Cell at any
of the three OM (See P.3.3.2.2.1) which means that more feed-water will be
required. Furthermore this numbers are not sensitive to the extra utilisation
of feed-water by the Electrolyser to cover the hydrogen demand of the
Storage Tanks if the latter are to be unexpectedly introduced to the primary
energy production scheme (PES). Nevertheless we can still use those values
as a convenient type of the minimum feed-water consumption indicators
that we would require to construct a natural deposit that will concentrate
fresh (rain) feed-water fuel for SES plant.
From the other study on the Eco-Village Reference: LE-36 by Mr Angelos
Mademlis and from the descriptions given in P.2.1.3 about the morphology
of the area on the Thornylee hill, where the village will be situated, we know
that the natural reservoir will have a volume of 4,500 m3 which is much
bigger than the modicum value of 68.9 m3 that the SES scheme would
require for a successful operation.
3.2.2.2. Critical Number of Storage Tanks and Critical Number of

Charging Days
As we have said before it is important to keep an undisturbed flow of
energy from the Storage Tanks to the Fuel Cell when the front line channel
(PES-Electrolyser-Fuel Cell) will fail due to any imponderable factors, that is
mechanical, electrical or climatic anomalies. A reasonable number of days
93
for that backup channel could be 15 days or 360h in which time all
maintenance and repairing operations could be completed. Thus in that time
frame we have from (Eq.3.10):
VH 2
V&H 2 =
t
Or,
VH2 = V&H 2 * t = 7.87 Nm 3 / h *360h
VH2 =2,637.7 Nm3 … (Equation 3.11)
Or in cubic meters from Table 12 above,
VH2 = 2,455.7 m3 … (Equation 3.11.1)

Or in litres
VH2 =2,460,000lt… (Equation 3.11.2)
This is a very large number, mainly because it refers to a calculation based

on standard conditions density. But the selected container (VS11000NC
model) will have different conditions for the accommodated gases, higher
pressure and temperature so there should be a theoretical decrease in that
volume since density is a function of pressure of and temperature for
hydrogen gases and in those conditions we would expect to increase as the
other two variables increase. So to decrease the volume we must calculate
the new density ρ PVessel for the same mass. Use (Eq.3.7) again where,
P: Pressure of the hydrogen gases, here P=26.7bar or 27.6MPa (seeP.3.2.1.3)
Z: Compressibility Factor, here Z=1.014,
ρ PVessel : Density in Kg/ m3 ,
R: Specific Gas constant for H 2 gas or R=4,128.18 Nm/KgK and
T: Temperature of the gases, here T=353K (seeP.3.2.1.3)
Therefore we have:
ρ PVessel =2.21 Kg/ m3 … (Eq.3.12)
If the mass of the hydrogen gases is in standard conditions:
mSC = ρSC *2,455.7 m3 =2,175.75Kg
94
Then the new volume of the gases will be:
mSC
VH 2 ( PVessel ) =
ρPVessel … (Equation 3.13)
= 984.5 m 3 = 985,000lt=1,056.36 Nm3 (See Table 3.12)
Thus the volume of the gases was considerable reduced at these conditions.
So the Critical Number of Storage Tanks will be:
984.5
N CPVessels = ≈ 5 … (Equation 3.14)
192
From P.3.2.1.1 we selected the H2 IGEN® 1000 Series Electrolyser which

&
can provide VIGEN =60 Nm 3 / h . So the Electrolyser can offer in 1 hour: 60-
7.87 Nm3 =52.13 Nm3 (the 7.87 Nm3 will be used directly for the Fuel Cell) and
so for the 1056.36 Nm3 of the containers the critical day(s) for charging will
be:
N CCDays =20.26h ≈ 1day… (Equation 3.15)
If the analysis was for 1 month (720h) then we would have:
V * H 2 ( PVessel ) =1924.5 m 3
N *CPVessels ≈ 10
N *CCDays =39.61h ≈ 2days
3.3 Rudimentary Simulations

With the use of computer software the complex analysis of REST
integration to the Eco-Village can become very straightforward. The
thought is to take advantage of that powerful assistance and simulate two
cases of energy supply to appropriate demands under real weather
conditions as we defined before. The two scenarios for these cases reveal
our intention to examine, according to the objectives of the project, as much
as possible a justifiable and realistic demand-supply relationship with all the
possible inventory that we could dig out from the software’s databases or
that we could assemble ourselves with the appropriate designing tools
95
within the program. The first step was to get familiar with the “facilitator”,
that is MERIT, to discover its full potential and then to start fitting together
the two plans.
3.3.1 MER IT- Analysis

In our hands there were two versions of MERIT, the v.2.2 and v.1.0
respectively. For reasons explained in P.4.3.1 we will present here the partial
investigation on the oldest version i.e. v.1.0 which was the one for
conducting the simulation for the two scenarios Reference: IS-16 . In this paragraph
we intend to give some light to the program itself and especially to describe
those aspects and components that will help to the understanding of the
procedures followed to establish the simulations of the two demand
scenarios (Scenario 1 and 2). When the user firstly runs the “MERIT.exe”
program it will see a set two columns of buttons on the left and the right
hand side of the main window that is called the Main Program Window
(Figure 3.7).
Figure 3.7/ Main Program Window
On the top there are the menus “File” and “Help” and in the centre there are
four windows referring briefly to the variables selected at the three
components of the preliminary and middle-phase control platforms. The
preliminary-phase control platform corresponds to the first of the four
buttons of the left-hand-side-column, namely the “Specify Analysis Conditions”
button, and the middle-phase control platform to the second and third
buttons (from the top), namely the “Specify Demand” and the “Specify Supply”
buttons. The simulation-phase control platform can be reached by the last
of the left hand side column buttons i.e. the “Match and Dispatch” one. The
right-hand-side-column buttons are pretty much self explanatory for their
operations. Since our work was involved with all the control platforms we
96
will look upon the most critical points of these components so that the
reader can have a complimentary theoretical idea to the practical analysis
facts.
Specify Analysis Condition

This is the preliminary-phase control platform and through that someone
can set the parameters for the initial stage of the simulation. From here, the
Analysis Parameter Window (Figure 3.8) someone can select a climatic
profile already bestowed in the climatic database of this section.
Figure 3.8/ Analysis Parameter Window
Someone can also select a customised profile that has developed with the
help of “CreateClimate.exe” (See Figure 3.9) and has delivered into the same
climatic database in the MERIT directory in the hard drive space. The
“CreateClimate.exe” is a program that could not be found at the v.1.0 of
MERIT but only in v.2.2 and it can help the user to build a “.clm” file from
an external source, provided that the file to be converted is in a compatible
form or “.csv” file form.
Figure 3.9/ CreateClimate.exe
97
Specify Demand
After a satisfactory climatic model has been selected the user can delve into
middle-phase control platform through the first of the two buttons
corresponding to this phase. The main interaction feature that is allowing
such a task is the Demand Definition Window (Figure 3.10) that contains
the following main functions:
• “Load Database”
• “Import Profile”
• “Profile Designer”
Figure 3.10/ Demand Definition Window
On selection of the “Load Database” function-button brings up a variety of

existing profiles which may be selected using the “Accept Profile” function-
button, or chosen for combining with others using the “Accept to
Combine” function-button. Up to nine profiles (single or combined) may be
chosen. Another important component of this platform is the “Profile
Designer”. Double clicking on “Profile Designer” function-button brings up
the Profile Designer Standard Window (Figure 3.11), in which there are
more existing profiles to be amended for a desired result.
Figure 3.11/ Profile Designer
98
Clicking on the tabs at the top brings up details of these profiles on the
Profile Tab Window. This half-hourly data can be amended manually, or
the overall consumption can be changed. Someone can also change the
specified time frame or days for which a profile is defined for. Going back
to the “Standard” tab, an annual profile can be generated by pressing
“Generate Annual”, and the radio buttons should be used to choose which
type of profile is desired (real, thermal, hot water).
Specify Supply
This is the other middle-phase control platform where the supply profiles
can be selected and that is possible in a two-part approach. The first part is
by determining the “Renewable Generating Systems” and the second by the
“Auxiliary Systems” specification. When the Supply System Definition
Window (Figure 3.12) first appears, the list at the top contains the following
functions-buttons:
• “Simulated Supply Profiles”

• “Supply Database”
• “Import Profile”
• “Supply Profile Designer”
99
Figure 3.12/ Supply System Definition
Double clicking on “Simulated Supply Profiles” button brings up a variety

of generation methods. Double clicking on each generation type brings up
its Generation Type Definition Window (Figure 3.13) , on which the user
can input readily available manufacturers information. Also, “Open” on the
“File” menu allows a variety of existing information to be accessed by
double clicking on the desired profile on the window which appears. This
information may be used or augmented as necessary.
Figure 3.13/ Generation Type Definition
When the “Auxiliary Definition Window” (Figure 3.14) first appears, the
list at the top contains a variety of auxiliary system types. Again, double
clicking on one of these brings up the “Relevant Definition Window”
which functions in the same way as the supply windows. As the
performance of the auxiliary systems can not be calculated until the demand
100
and supply matching stage, a description of the system appears in the
window when the definition windows are exited. If this is satisfactory, it may
be accepted and combined in exactly the same way as for the demand
profiles.
Figure 3.14/ Auxiliary Definition Window
Match & Dispatch

As the last stage of the phases this is the simulation-phase control platform
with which the work is completed. When the “Match and Dispatch
Window” (Figure 3.15) opens, the chosen demand, supply and auxiliary
profiles will be seen as buttons at the top, in the middle. Any number of
profiles may be chosen for matching. The box at the top right hand corner
contains information about the match. There are 6 indicators which the user
can consult to retrieve the best information about his/hers selections from
the previous steps. Indicator Inequality refers to the difference in the phase
for demand-supply profiles. If for example at summer a PV can offer more
energy than that the EV requires and at winter can not reach the required
values the match will have a large inequality. Indicator Correlation refers to
the difference in the magnitude for demand-supply profiles. A small
difference in magnitude will result in large correlation. There are also
indicators Deficit and Excess which their difference can give the value of the
magnitude for demand-supply profiles. This can be verified by the top left
hand corner box indicators namely the Selected Demand and Selected Supply by
the equation:
Selected Demand –Selected Supply = Deficit-Excess... (Equation 3.17)
101
So if Deficit-Excess<0 then there is an excess amount of energy to be utilised
and the closest this value is a zero the better Equation 3.17 is verified and
the better are the matching results. Different combinations can be tried out,
and it is possible, at any time, to go back to the earlier stages and amend
demand, supply and auxiliary data to help improve the match. Three graphs
are shown at the bottom:
• Demand and Supply

• Residual Power
• Auxiliary Performance
All potential matches can be assessed automatically against various criteria

by using the “Auto Search” function-button. When this is pressed, a
“Criteria Definition Window” (Figure 3.16) appears on which a variety of
criteria may be selected for the match. Each possible match is then
evaluated against these criteria, and results are suggested.
Figure 3.15/ Match and Dispatch
102
Figure 3.16/ Criteria Definition
3.3.2. Scenarios Design

There are two possible demand-supply relationships. A unipolar one where
the objective is to explore the applicability of Wind Turbines and
Photovoltaic systems into providing Electrical Energy (E El ) to the Eco-
Village and a bipolar where the objective is to check the degree of matching
Electrical Energy from PES with SES for providing Electrical and Thermal
Energy ( E El and ETh ) to the Eco-Village. The first relationship is named as
Scenario 1 and the second as Scenario 2. The importance of Scenario 1 is
mainly due to the fact that we will realise the implementation possibility of
two well known solutions for autonomous communities at the area of
interest and that the deduced results from that study could be compared
with those arising from the other project on this Eco-Village by Angelos
Mandemlis Reference: LE-36 which studies electrical coverage in a similar fashion.
The importance of Scenario 2 is focusing on the possible implementation of
a new way for establishing thermal and electrical coverage for a community
i.e. the Fuel Cell modules.
3.3.2.1 Scenario 1
The beginning of the experiments (Attempts) for this scenario start with the
appropriate selection of PES. Even before the choice of the Photovoltaic
modules it is necessary to select a felicitous type of Wind Turbine (from
MERIT’s database) since its multiples will embrace the core of the electrical
load E El . That Wind Turbines are known for their large capacities in kW will
readily make them the framework of PES. To succeed such a selection we
need to know the daily power requirement of the village. As we saw from
P3.2.2 the Electrical Energy the Eco-Village requires for 1 year is:
103
EElV = 68,000kWh,
Or in 1 day
EEl 1 =186.30kWh
V
So the theoretical power that is required by PES, in one day, will be:
*
PEl1 =7.76kW
This critical number can help us determine the kind of turbine for the PES
framework. MERIT has a number of turbines in its database in different
sizes (power outputs) ranging from 1kW to 1.3MW. We can choose a 3 kW
*
turbine or a 10 kW one since both of them are close to the value of PEl1 . It
was proved by a roughcast MERIT experiment that the actual power that a
turbine can offer is much less than the nominal power for a given type of
electrical demand and the corresponding climatic profile. So with this tolling
observation in hand we decided that a 10 kW turbine will provide better
results when multiples will be required for the simulation. Thus the turbine
type that we selected was the LMW-10KW model from the LMW
Company. In that case we might need to make a small farm at the top of
Thornylee hill. There is not much information about the company or the
turbine itself on the internet Reference: IS-19 except that where we found from the
Generation Type Definition Window in MERIT database about the
technical parameters of that turbine (Table 3.13)
Table 3.13/ Technical Characteristics for LMW-10KW turbine

Turbine Type
Stall Regulated
Power Curve Parameters (Density of Air: 1.225Kg/m3)
Cut In Speed
3 Power (kW) 0.01
(m/s)
Nominal Speed
12 Power (kW) 10
(m/s)
Peak (m/s) 16 Power (kW) 10
Cut Out (m/s) 22 Power (kW) 5
Positioning Parameters
Height above ground (m) 18
To start the simulation in the form of experiments (Attempts) we firstly

require the climatic model of the area that is to be simulated (P.3.1) and then
a demand profile that would set the electrical or thermal conditions for the
supply (in this case just electrical conditions). In MERIT’s database there are
104
a lot of fixed profiles for a number of possible situations – domestic and
industrial (P.3.3.1). Unfortunately v.1.0 did not contain a profile that could
assimilate the value of EElV and thus we looked at the database of the
newest version v.2.2 to find any particular profile of good approximation.
Indeed that we found in the database “UK” under “Load Factor 0-20%”.
There were again many profiles but only one could approximate the
EElV value and that was “Variability 25% above Base Load”. So by comparison:
EElV = 68,000kWh,
And
EEl M =66,015.2 kWh
This is really not too unseasonable for representing the default demand and
thus we accepted it for the simulation. Now that demand profile was set we
only had to experiment with the REST to find out what results would we
get on the subject of electrical matching. The experimental phase itself was a
mixture of two complimentary phases’ i.e. a preliminary phase (PP) and a
main phase (MP). The first would allow an insight into the associations of
demand-supply selections and would provide sound candidates for the
introduction of batteries, whereas the second would integrate the selected
candidates into completed patterns for comparisons and analysis. The PP
was a set of 9 Attempts and the MP a set of 6. Below Tables 3.14a and
3.14b have the details for the PP and Table 3.15a and 3.15b for the MP. A
detailed analysis of the two phases can be found at P.4.3.2.1 and P.4.3.2.2
respectively.
Table 3.14a/ Match Results for Preliminary Phase -Scenario 1, PP

Name of Experiment 1st Attempt - Scenario 1 2nd Attempt - Scenario 1
Characterisation Code 1 Turb-No Aux. Electr. Recovery 2 Turb-No Aux. Electr. Recovery
Assessment Parameters:
Inequality 0.5432 0.4564
Correlation 0.105 0.105
Excess (KWh) 8321.17 27791.5
Deficit (KWh) 43649.6 32433.1
Current Match Very Poor Match 4/10 Poor Match 5/10
Potential Match Rating No significant improvement With moderate storage : 8/10
Auxiliary System Performance - -
Name of Experiment 3rd Attempt - Scenario 1 4th Attempt - Scenario 1
Characterisation Code 3 Turb-No Aux. Electr. Recovery 2 Turb+19 BP130L-No Aux.
Electr. Recovery
105
Excess (KWh) 53392.8 28555.9
Deficit (KWh) 27347.5 31262.9
Current Match Poor Match 5/10 Poor Match 5/10
Potential Match Rating With moderate storage 6/10 With moderate storage 9/10
Name of Experiment 5th Attempt - Scenario 1 6th Attempt - Scenario 1
Characterisation Code 2 Turb+38 BP130L-No Aux. Electr. 2 Turb+76 BP130L-No Aux.
Recovery Electr. Recovery
Excess (KWh) 29408.4 31364.8
Deficit (KWh) 30180.8 28267.9
Characterisation Code 2 Turb+100 BP130L-No Aux. Electr. 2 Turb+100 SM110-No Aux.
Excess (KWh) 32739.6 31240
Deficit (KWh) 27198.9 28404.2
Name of Experiment 9th Attempt - Scenario 1
Characterisation Code 2 Turb+150 SM110-No Aux. Electr.
Recovery
Inequality 0.4222
Correlation 0.2191
Excess (KWh) 33364
Deficit (KWh) 26789.6
Current Match Poor Match 5/10
Potential Match Rating With moderate storage 8/10
Auxiliary System Performance -
106
Table 3.14b/ Analytical Record of MERIT Selection Parameters for REST
–Scenario 1, PP
Name of Experiment 1st Attempt - Scenario 1 2nd Attempt - Scenario 1
Characterisation Code 1Turb-No Aux. Electr. Recovery 2 Turb-No Aux. Electr. Recovery
Discription:
Turbines • 1 LMW Turbine • 2 LMW Turbines
• Terrain: “Open Agricultural • Terrain: “Open Agricultural
with little Shelter” with little Shelter”
• Wind Speed Measurements: • Wind Speed Measurements:
“Standard Meteorological “Standard Meteorological
Observations” Observations”
Photovoltaic Modules N/A N/A
Name of Experiment 3rd Attempt - Scenario 1 4th Attempt - Scenario 1
Characterisation Code 3 Turb-No Aux. Electr. Recovery 2 Turb+19 BP130L-No Aux.
Electr. Recovery
Discription:
Turbines • 3 LMW Turbines • 2 LMW Turbines
Photovoltaic Modules N/A • 19 Units - BP130L
• “Employ Daily Tilt
Optimisation”
Characterisation Code 2 Turb+38 BP130L-No Aux. Electr . 2 Turb+76 BP130L-No Aux.
Discription:
Photovoltaic Modules • 38 Units - BP130L • 76 Units - BP130L
• “Employ Daily Tilt • “Employ Daily Tilt
Optimisation” Optimisation”
Characterisation Code 2 Turb+100 BP130L-No Aux. Electr. 2 Turb+100 SM110-No Aux.
Discription:
Photovoltaic Modules • 100 Units - BP130L • 100 Units – SM 110
• “Employ Daily Tilt • “Employ Daily Tilt
Optimisation” Optimisation”
107
Name of Experiment 9th Attempt - Scenario 1
Characterisation Code 2 Turb+150 SM110-No Aux. Electr.
Recovery
Discription:
Turbines • 2 LMW Turbines
• Terrain: “Open Agricultural
with little Shelter”
• Wind Speed Measurements:
“Standard Meteorological
Observations”
Photovoltaic Modules • 100 Units – SM 110
• “Employ Daily Tilt
Optimisation”
Table 3.15a/ Match Results for Main Phase -Scenario 1, MP

Characterisation Code 3 Turb -BB with C=2365Ah 3 Turb-BB with C=3931.2Ah
Parameters:
Excess 35081.9 33929.1
Deficit 13580.2 11560.1
Potential Match Rating With increased storage 8/10 With increased storage 8/10
Auxiliary System Performance Total Energy Loss:77684.59Ah Total Energy Loss:89190.27Ah
Total Energy Gained:65751.95Ah Total Energy Gained:69413.05Ah
Characterisation Code 2 Turb+76 BP130L-BB with 2 Turb+76 BP130L-BB with
C=2365Ah C=3931.2Ah
Parameters:
Excess 15373.8 13951.6
Deficit 15322.2 13183.5
Current Match Reasonable Match 6/10 Reasonable Match 6/10
Total Energy Gained:59190Ah Total Energy Gained:64045.06Ah
Characterisation Code 2 Turb+100 SM110-BB with 2 Turb+100 SM110-BB with
C=2365Ah C=3931.2Ah
Parameters:
Excess 15151.4 13646.4
108
Deficit 15388.2 13196
Current Match Reasonable Match 6/10 Reasonable Match 6/10
Total Energy Gained:59569.09Ah Total Energy Gained:64720.13Ah
Table 3.15b/ Analytical Record of MERIT Selection Parameters for REST

–Scenario 1, MP
Characterisation Code 3 Turb-BB with C=2365Ah 3 Turb-BB with C=3931.2Ah
Description:
• Terrain: “Open Agricultural with • Terrain: “Open Agricultural
little Shelter” with little Shelter”
Photovoltaic Modules N/A N/A
Battery Bank • 215Ah@12V • 215Ah@12V
• 18 in Series • 18 in Series
• 191 in Parallel • 330 in Parallel
Characterisation Code 2 Turb+76 BP130L-BB with C=2365Ah 2 Turb+76 BP130L-BB with
C=3931.2Ah
Description:
Photovoltaic Modules • 76 Units - BP130L • 76 Units - BP130L
• “Employ Daily Tilt Optimisation” • “Employ Daily Tilt
Optimisation”
Characterisation Code 2 Turb+100 SM110-BB with C=2365Ah 2 Turb+100 SM110-BB with
C=3931.2Ah
Description:
109
Photovoltaic Modules • 100 Units – SM 110 • 100 Units – SM 110
• “Employ Daily Tilt Optimisation” • “Employ Daily Tilt
Optimisation”
3.3.2.2. Scenario 2
From the four consecutive stages in MERIT (see P.3.3.1) only the first one
–the “Specify Analysis Conditions” can be used as a main part for the two
scenarios. After that stage there is a bifurcation between Scenario 1 and 2.
In Scenario 2 instead of using a default database for the demand of the Eco-
Village we used the “Demand Profile Designer” tool that is offered at the
“Specify Demand” middle-phase control platform to construct an electricity
profile for SES and then use the selected ReST as we did with Scenario 1 to
simulate that profile. So in Scenario 2 the simulation will not be on the
energy demand of the Eco-Village directly but on that of the Fuel Cell plant
and more specifically of the Electrolyser since this is the only component of
the Fuel Cell plant that is electrically connected to PES. Thus the electrical
and thermal demands of the Eco-Village (E El and ETh ) will be translated
into electrical demand for the Electrolyser, over one year of operation, to
provide the necessary fuel for the Fuel Cell that in continuant operation
mode will supply the Eco-Village with electrical and thermal loads.
Obviously some of the hydrogen fuel will be provided to the tanks so that
an uninterruptible flow of energy occurs to the houses.
3.3.2.2.1 Fuel Cell Operating Modes

To make a more realistic simulation for the Fuel Cell plant we have to
consider the fact that the latter will confront different loads over different
seasons, which will vary the demand for hydrogen fuel and likewise the
corresponding electrical demand for PES. Obviously there will be a
difference in the ED of the Eco-Village during the summer against that
during the winter and that would apparently affect the operation of the Fuel
Cell components. The solution that we thought about this problem was to
make up a profile for the operation of the Fuel Cell in accordance to the
seasonal demand for the village, which would be comprised by 3 different
operation modes (OM) for the days of operation. The “Profile Designer”
that MERIT possess (see P.3.3.1) allows for a partial representation of any
energy demand for different periods by configuring…So we represented the
4 seasons by 4 Weekdays and 4 Weekend days and then we integrated that
energy profiles over the year to get the demand for the Electrolyser demand.
The 4 Weekdays and 4 Weekend energy consumption was determined by
110
the OM of the Fuel Cell for the 4 seasons and that can be seen in Tables
3.16a, 3.16b and 3.16c below. We already know from (Eq.1) and (Eq.3) that:
ED =132,000kWh
PD1 = 361.64 =15kW

*
24
This is power we will use for the base-load demand of the Fuel Cell. The
question is what can we use as sub-base load and peak-load demands? To
answer that question we have to consider what will be an ideal size for the
Fuel Cell relative to its Operational Capacity Range (OCR). Say for example
that we have a 15kW and a 25kW Fuel Cell for the needs of the Eco-Village
both reaching these watts at maximum operation (100% of OCR). Then at
peak-load demand the 25kW Fuel Cell will have to work at 90% of its OCR
to give 22.5kW whereas the 15kW Fuel Cell will have to work at 112.5% of
its OCR to succeed the same power. So the first will a Capacity Cushion
(CC) of 10% and the second a negative CC of -12.5%. This is not a
satisfactory operation activity for the 15kW Fuel Cell, as it will strain its
performance and possibly damage the module after some time, and so we
have to choose the 25kW Fuel Cell for the ED for the village. Thus the
Operation Modes (OM) will be:
• OM 3 =Sub-Base Load=30%*25kW =7.5 kW

• OM 1 =Base Load= 60%*25 kW=15 kW
• OM 2 =Peak-Load=90%*25 kW=22.5 kW
For the base load we know the Fuel Cell requirements in terms of hydrogen
fuel and the corresponding electricity for the Electrolyser (see P.3.2.1.1). We
follow the same theoretical calculations to get the values of the same
parameters for the three modes:
• OM 3 =3.93 Nm3 / h , Electrical Demand for Electrolyser =19.65kW

• OM 1 =7.87 Nm3 / h , Electrical Demand for Electrolyser= 39.35kWh
• OM 2 =11.80 Nm3 / h , Electrical Demand for Electrolyser =59kWh
111
Key for Colours
OM1 Base Load = 25kW * 60% of total power = 15KW
OM2 Peak Load = 25kW * 90% of total power = 22.5KW
OM3 Sub-Base Load = 25kW * 30% of total power = 7.5KW
Table 3.16a/ Operating Modes for the Seasonal Profile- 1 Year

Winter Spring Summer Automn
Number of Hours/Day Weekday Weekend Weekday Weekend Weekday Weekend Weekday Weekend
0 OM3 OM3 OM3 OM3 OM3 OM3 OM3 OM3

Table 3.16b/Corresponding Seasonal Energy Demand for Electrolyser

(kWh)
Number of Week Week Weekda Weeke Weekd Weeken Weekday Weekend

Hours/Day day end y nd ay d
0 19.65 19.65 19.65 19.65 19.65 19.65 19.65 19.65
1 19.65 19.65 19.65 19.65 19.65 19.65 19.65 19.65
2 19.65 19.65 19.65 19.65 19.65 19.65 19.65 19.65
3 19.65 19.65 19.65 19.65 19.65 19.65 19.65 19.65
4 19.65 19.65 19.65 19.65 19.65 19.65 19.65 19.65
5 19.65 19.65 19.65 19.65 19.65 19.65 19.65 19.65
112
6 39.35 39.35 39.35 39.35 39.35 39.35 39.35 39.35
7 59 39.35 59 39.35 39.35 39.35 59 39.35
8 59 59 39.35 59 39.35 39.35 59 59
9 39.35 59 39.35 59 39.35 39.35 39.35 59
10 39.35 39.35 39.35 39.35 39.35 39.35 39.35 39.35
11 39.35 39.35 39.35 39.35 39.35 39.35 39.35 39.35
12 39.35 39.35 39.35 39.35 39.35 39.35 39.35 39.35
13 39.35 39.35 39.35 39.35 39.35 39.35 39.35 39.35
14 39.35 39.35 39.35 39.35 39.35 39.35 39.35 39.35
15 39.35 39.35 39.35 39.35 39.35 39.35 39.35 39.35
16 39.35 39.35 39.35 39.35 39.35 39.35 39.35 39.35
17 59 39.35 59 59 39.35 39.35 59 59
18 59 59 39.35 39.35 39.35 39.35 39.35 39.35
19 39.35 39.35 39.35 39.35 39.35 39.35 39.35 39.35
20 39.35 39.35 39.35 39.35 39.35 39.35 39.35 39.35
21 39.35 39.35 39.35 39.35 39.35 39.35 39.35 39.35
22 39.35 39.35 39.35 39.35 39.35 39.35 39.35 39.35
23 19.65 19.65 19.65 19.65 39.35 39.35 39.35 39.35
Table 3.16c/ Corresponding Seasonal Hydrogen Demand for Electrolyser

( Nm 3 / h )
Number of Hours/Day Weekday Weekend Weekday Weekend Weekday Weekend Weekday Weekend
0 3.93 3.93 3.93 3.93 3.93 3.93 3.93 3.93

1 3.93 3.93 3.93 3.93 3.93 3.93 3.93 3.93
2 3.93 3.93 3.93 3.93 3.93 3.93 3.93 3.93
3 3.93 3.93 3.93 3.93 3.93 3.93 3.93 3.93
4 3.93 3.93 3.93 3.93 3.93 3.93 3.93 3.93
5 3.93 3.93 3.93 3.93 3.93 3.93 3.93 3.93
6 7.87 7.87 7.87 7.87 7.87 7.87 7.87 7.87
7 11.8 7.87 11.8 7.87 7.87 7.87 11.8 7.87
8 11.8 11.8 7.87 11.8 7.87 7.87 11.8 11.8
9 7.87 11.8 7.87 11.8 7.87 7.87 7.87 11.8
10 7.87 7.87 7.87 7.87 7.87 7.87 7.87 7.87
11 7.87 7.87 7.87 7.87 7.87 7.87 7.87 7.87
12 7.87 7.87 7.87 7.87 7.87 7.87 7.87 7.87
13 7.87 7.87 7.87 7.87 7.87 7.87 7.87 7.87
14 7.87 7.87 7.87 7.87 7.87 7.87 7.87 7.87
15 7.87 7.87 7.87 7.87 7.87 7.87 7.87 7.87
16 7.87 7.87 7.87 7.87 7.87 7.87 7.87 7.87
17 11.8 7.87 11.8 11.8 7.87 7.87 11.8 11.8
113
18 11.8 11.8 7.87 7.87 7.87 7.87 7.87 7.87
19 7.87 7.87 7.87 7.87 7.87 7.87 7.87 7.87
20 7.87 7.87 7.87 7.87 7.87 7.87 7.87 7.87
21 7.87 7.87 7.87 7.87 7.87 7.87 7.87 7.87
22 7.87 7.87 7.87 7.87 7.87 7.87 7.87 7.87
23 3.93 3.93 3.93 3.93 7.87 7.87 7.87 7.87
3.3.2.2.2 “Demand Profile Designer” and “Specify Demand”

Numerical Configurations
For “Demand Profile Designer” numerical configurations we need to look back
at P.3.3.1 for a basic knowledge of the environment that the user will come
across when trying to define a demand profile. In this case we firstly set the
number of days for the demand profile by choosing the “Standard Tab” (See
P.3.3.1). According to the requirements of the Fuel Cell operating modes
these had to be Weekday 1-4 and Weekend 1-4 for the four seasons. The
parameters were set as described below in Table 3.17. Then the “Profile
Effects Tab” had to be structured and arranged.
Table 3.17/ Parameters for “Demand Profile Designer”

“Week Days”-Tabs Recordings
Parameters Weekday 1 Weekday 2 Weekday 3 Weekday4
"Daily Consumption" in KWh 885.1 845.8 752.325 870.375
"Apply Profile to Days" M,T,W,T,F
"Apply Profile to Period" 01/01-31/03 01/04-30/06 01/07-30/09 01/10-31/12
Weekend1 Weekend2 Weekend3 Weekday4
"Daily Consumption"in KWh 865.45 865.45 747.4 885.15
"Apply Profile to Days" M,T,W,T,F
"Apply Profile to Period" 01/01-31/03 01/04-30/06 01/07-30/09 01/10-31/12
“Profile Effect” -Tab Recordings
"Treatment of Undifined Periods" 1st Option: Interpolate between defined periods
“%Variabilty" 2nd Option: Apply to whole profile
"Temperature Effects" N/A
"Daylight Effects" 4th Option: Stretch profile with daylight hour
For the “Profile Effect” tab we came across a difficulty to choose how much
should we set the “%Variability” to produce a realistic profile. By inspection
we had:
• “%Variability”=0% then Total Annual Consumption=296,926kWh

• “%Variability”=2.5% then Total Annual Consumption=306.432kWh
• “%Variability”=8% then Total Annual Consumption=421,976kWh
114
The second choice seemed the most appropriate. Then we saved the
template and we generated an annual profile with the “Generate Annual”
button to get the demand for the electrolyser. The total demand was
306,839kWh with all the effects of the “Profile Effect” tab on. This was a
relatively large value (almost the double) compared with that of Equation 1
that specified ED = 132,000 kWh. This indicated that the analysis on the
OM was overestimated and it had to be scaled for a realist simulation. We
modified this result by using the “Annual Consumption” feature in the
Demand Definition Window (See Figure 3.10) to integrate the
306,839kWh to 132,000 kWh and that was the final value for the simulation.
After all the necessary numerical configurations for the “Specify Demand”
stage of Scenario 2 were completed we began the selection of ReST for the
electrical demand of the Eco-Village. As for Scenario 1 we used the LMW-
10KW turbine model from MERIT’s database and the BP130L and SM110
photovoltaic modules for the experiments of Scenario 2. The only
difference was the insertion of a 3 kW turbine to adjust the matching as a
means of improvement measures. The phase was completed with 8
experiments (Attempts) which can be seen in Tables 3.18a and 3.18b below.
Table 3.18a/ Match Results for Scenario 2

Characterisation 2Turb-No Aux Electr Recovery 4Turb-No Aux Electr Recovery
Parameters:
Excess 7800.07 49666.4
Deficit 78424.3 58917
Potential Match Rating No significant improvement With moderate storage 8/10
Auxiliary System
Performance
Characterisation 5Turb-No Aux Electr Recovery 4 Turb+8 BP130L-No Aux Electr Rec
Parameters:
Excess 75668.1 50076.6
Deficit 54231.8 58512.7
Auxiliary System
115
Performance
Name of Experiment 20th Attempt - Scenario 2 21st Attempt - Scenario 2
Characterisation 4 Turb+15 BP130L-No Aux Electr 4 Turb+40 BP130L-No Aux Electr Rec
Rec
Parameters:
Excess 50439.1 51769.5
Deficit 58162.3 56947.1
Auxiliary System
Performance
Name of Experiment 22nd Attempt - Scenario 2 23rd Attempt - Scenario 2
Characterisation 4 Turb+40 BP130L+1Turb-No Aux 4 Turb+20 BP130L+1Turb-No Aux
Electr Rec Electr Rec
Parameters:
Excess 59780.2 58672.5
Deficit 55097.6 56026.4
Auxiliary System
Performance
116
End of Chapte r 3
117
Chapter 4-Discussion
It is necessary for the reader to understand the analysis of the experiments of the previous chapter in order to
modulate a complete idea about their actual conductance. Any of the results taken throughout this project were
assessed for their integrity and to specify if either their modulation was required or their status was rigid enough to
provide a solution. That was the tactic overall.
4.1 Climatic Analysis

The choice of appropriate stations with the essential climatic information
was not easy at all since most of them were not referring to the area of study
(Thornylee Forest) or the year of examination. We had to improvise
techniques to bypass these difficulties with reasonable assumptions that
would lead to a compromise between the problems faced and the
conductance of the simulation.
4.1.1 Evaluation Process Remarks

From the last chapter we met the evaluation process for screening a number
of stations to a working level. Via this process we could actually find out the
quality of weather data that the stations under examination were endowed
with and to identify their potential for a prolific application concerning the
construction of the climatic file. From this process we could distinguish the
veins and impasses of the Domains of the File Formats to a practical extend
that decisions could be made about the formation of the climatic file for
MERIT. Some of the remarks in this section will be upon the results of
Table 3.7 and some other will come from the generic contact that the author
had with the Domains in the BADC databases for the qualified stations of
the evaluation stage – these can be identified by the Association number as
found in the before mentioned table.
Referring to Table 3.7, we can identify two stations with the highest
total score (8) readily discerning amongst the other 9 stations. This is the
result of two facts. Both of the stations have a complete observations record
for the three File Formats that we were looking for (.hwx, .radt and .wind)
and since the quality of these formats is important as well both of them have
the most appropriate type of data structures i.e. {1}, {5}, {6}, {7} {9}, {13},
{10, jointly. These structures are rendered with the highest Ordinance –
Table 3.6. When Availability is concerned we can see again from Table 3.7
that Eskdalemuir and Drumalbin Saws have up-to-date weather records,
another useful point when flexibility of utilization is regarded. Thus very
rightfully these two stations can qualify for any use in the construction of
the MERIT climatic file. The ReST of the 9 stations are deemed inadequate
for this scope for low scoring or for small QPA. The only exception will be
made for Chartehall Saws since it is the only station with a .radt file and that
is very important since most of the .radt files that were examined had high
118
inconsistencies and deficiencies in registering radiation data. Having said
that, we can now present the problems of information flaws in registering
radiation data and the dilemma of choosing stations for wind values (relative
to their advantageous distance to the Thornylee Forest) or to their similitude
with climatic measurements that MERIT requires i.e. on a 1h-basis
measurement steps on 24h/daily cycles.
4.1.1.1 Radiation Problems

With the examination of 10 Domains for 11 stations we observed
inconsistencies and deficiencies in registering radiation data. For the
construction of MERIT climatic file we require 6 fields (see P.3.1.5). For
radiation fields the file must be completed with diffuse solar intensity ( I d )
on the horizontal and direct normal solar intensity (I n ) values in 1 hour
steps. But the three stations with radiation records (Rad1, Rad2 and Rad3 –
Association Numbers) can hardly provide these data since these values are
not embodied into the BADC files. The value -999 (BADC’s way to declare
a missing value) was stated under the diffuse solar intensity on the
horizontal and direct normal solar intensity columns in the data records.
Global radiation was recorded but unfortunately we could not exploit that as
we need other factors to make up the other two parameters only from that
radiation values. As a solution to this problem was to extend the search of
radiation File Formats to even more remote counties from Peeblesshire with
the hope of finding Domains with a better register on the I d and I n values.
That searching process can be found in P.3.1.4. Unfortunately this had not
the predictable outcome that we hoped for and so a third solution was to be
given to the problem.
With the help of an academic staff within the department we
managed to acquire a radiation file with vital information upon the crucial
solar intensity values ( I d and I n values). The station providing this
information was Eskdalemuir for the year 1978, we could not find the same
information at the BADC databases ourselves. The great thing about this
climatic file was that since it was used by some other weather-data intensive
software within the ESRU department (ESP-r) it was already modified in the
required MERIT configuration since the two are using the same architecture
of translating weather information into electronic climatic files. According
to the objective of the project for a realistic simulation using a radiation file
with meteorological observations from a different area (Dumfriesshire
County) and from a different time scale (24 years before) are two
discrepancies that we have to compromise effectively in order to stay on line
with that objective. This compromise will be based on the two assumptions
that state respectively:
119
A1: “When referring to solar insolation affecting a relatively small
geographical area of a country we can assume that localised geographical
radiation phenomena will fuse into solid irradiation behaviour within the
boundaries of the enclosed area of study”.
A2: “When referring to solar insolation affecting a relatively small
period of time we can assume that seasonally localised geographical
radiation phenomena will stay unaffected within the boundaries of that time
scale”.
These assumptions would simplify the problem of using a climatic file with
meteorological observations from another area and another time, such as
the ambiguous file of Eskdalemuir that we possessed. These assumptions
are obviously not a robust scientific approach to the problem but they can
help us bypass the latter without the risk of terminate the project. Thus they
were a significant compromise to the issue of climatic information. What
those assumptions simply state is that, for A1, the 19,800 Km2 of the area of
study (that is Delimitation Plan-A and B including Glasgow where we
finally got the climatic file for the simulation- see P????) are really small
compared to the 78,783 Km2 of Scotland’s mainland and, for A2, a time scale
of 30-50 years would be effectively small compared to 100 or 200 years of
possible climatic change of a place.
4.1.1.2 Wind Speed Problems

The problem with the wind speed value is of a different nature to the
radiation problem. In this case we could get valid measurements from the 11
stations of the Evaluation phase but stations close to the Thornylee Forest
had recordings on a 24h steps for each day (W1, W2, W3, W4, W5, W6,
W7, and W8 – Association Numbers) whereas the two stations on the more
remote areas (Rad1 and Rad2 – Association Numbers) were of the desired
format, 1h steps for each day. The binding requirement for a realistic
simulation is dictating for wind speed measurements at the area of
Thornylee Forest but that it is not possible in our case. Thus like before a
compromise but be established for allowing a safe conduct of the product.
Assumption 3 below states the conditions for using the .wind data from
stations Rad1 and Rad2 i.e. those with the most attractive parametrical
format (Table 5 and 6 in Chapter 3).
A3: “If any sites have the same morphological and climatic
characteristics with the site under climatic examination and belong to a
homogeneous geographical area with that target area, they can be deemed as
reasonably connatural to the natural weather behaviour of the critical area”.
120
In simpler words that assumption can allow for a more flexible
approach to the selection of a station with the required wind parameters
(speed and direction) remote from the area of study under the conditions
that the remote area has more or less identical characteristics in its
morphology with the target area and that its global and particular climatic
demeanour is essentially streamlined to that of the target area (provided that
the region for both of the stations is homogeneous). In our case the
morphological problem would be translated in similarities in elevation
between any areas of consideration and Thornylee Forest, the particular
climatic demeanour in divergence of the annual values for average wind
speed between any areas of consideration and Thornylee Forest, and the
global climatic demeanour in comparison of two seasonal weather profiles
for two random years. With this in hand we devised a CEACP approach
described in P.3.1.4 for the two top stations Rad1 and Rad2, as these were
the most effective stations wind-wise in order to select the most efficient for
wind data.
As we can see from Table 3.8 it is clear that by Step 2 the comparison
is very vague since the elevation and distance values are almost the same and
so there are no clear judgment factors for a sound selection. At Step 3
though we have the necessary bias for a decision towards Eskdalemuir
station since the average wind speed of the latter is closest to the value of
10m/s that the Thornylee Forest has. This reason is quite sufficient in
justifying the use of this station since the process is made for obtaining wind
data and such an inclination towards the critical value of 10m/s is a valid
proof for such a decision. So since we have selected ESKDALEMUIR for
wind data we need to test its climatic match with the weather at Thornylee
Forest. But from P.3.1.4 we know that there is no such station in that area
to give us meteorological observations and the closest is Bowhill station.
Tables 3 and 4 in Appendix A have the details of the local meteorological
measurements and from these tables we can make up graphs leading to
tangible means of comparisons for the climatic behaviour of the areas
around the stations. Below in Figures 4.1a, 4.1b, 4.2a, 4.2b, 4.3a and 4.3b we
are presenting only six graphs out of the ten possible, for just three of the
parameters namely wind speed, visibility and temperature, leaving the other
two out of this text for reasons of convenience. A quick examination of the
figures will show inconformity between the climatic parameters for the
chosen years. Wind speed and dry bulb temperature are almost following the
same pattern for the two stations, for both of the years and this is essentially
the critical point of validating the choice of Eskdalemuir and verifying the
assumption A3. Visibility’s graphs are truly very different between the two
stations but compared with the graphs of the other two parameters, which
have identical pattern configurations and are not shown here (total cloud
amount and wind speed direction), they can be overlooked in the greater
vision. So to finalise, the important weather parameters have few
121
discrepancies and that is acceptable for continuing the weather profile
configuration with wind data coming from Eskdalemuir station.
Figure 4.1a/ Dry Bulb Temperature comparative chart for 1994

Dry Bulb Temperature Measurements (9:00am)
1994
400
350
300
DbTemperature (Tenths of C)
250
200
150
100
50
0
1
5
10
15
20
25
30
1
5
10
15
20
25
30
1
5
10
15
20
25
30
1
5
10
15
20
25
30
-50
Januany April July October
Seasonal and Monthly Divisions
Bowhill-DbTemp-1994 Eskdalemuir-DbTemp-1994
Figure 4.1b/ Dry Bulb Temperature comparative chart for 1997

Dry Bulb Temperature Measurements (9:00am)
1997
400
350
DbTemperature (Tenths of C)
300
250
200
150
100
50
0
1
5
10
15
20
25
30
1
5
10
15
20
25
30
1
5
10
15
20
25
30
1
5
10
15
20
25
30
-50
Bowhill-DbTemperature-1997 Eskdalemuir-DbTemperature-1997
122
Figure 4.2a/ Visibility comparative chart for 1994
Visibility Measurements (9:00am) 1994
7000
6000
5000
Visibility (m)
4000
3000
2000
1000
0
1
5
10
15
20
25
30
1
5
10
15
20
25
30
1
5
10
15
20
25
30
1
5
10
15
20
25
30
Bowhill-Visibility-1994 Eskdalemuir-Visibility-1994
Figure 4.2b/ Visibility comparative chart for 1997

Visibility Measurements (9:00am) 1997
8000
7000
6000
Visibility (m)
5000
4000
3000
2000
1000
0
1
5
10
15
20
25
30
1
5
10
15
20
25
30
1
5
10
15
20
25
30
1
5
10
15
20
25
30

Bowhill-Visibility-1997 Eskdalemuir-Visibility-1997
123
Figure 4.3a/ Wind Speed comparative chart for 1994
Wind Speed Measurements (9:00am) 1994
50
45
40
Wind Speed (Knots)
35
30
25
20
15
10
5
0
1
5
10
15
20
25
30
1
5
10
15
20
25
30
1
5
10
15
20
25
30
1
5
10
15
20
25
30
Seasonal and Montly Divisions
Bowhill-WindSpeed-1994 Eskdalemuir-WindSpeed-1994
Figure 4.3b/ Wind Speed comparative chart for 1997

Wind Speed Measurements (9:00am) 1997
45
40
35
Wind Speed (Knots)
30
25
20
15
10
5
0
1
5
10
15
20
25
30
1
5
10
15
20
25
30
1
5
10
15
20
25
30
1
5
10
15
20
25
30

Bowhill-WindSpeed-1997 Eskdalemuir-WindSpeed-1997
124
4.1.2 Formation Process Commentaries
From the last chapter in P.3.1.5 we saw the final phase of the meteorological
methodology devised for the production of the climatic file that MERIT
needs to integrate a simulation between renewable technologies and demand
of the Eco-village but the reality was somewhat cruel with the outcome of
such a process. On trying to use the Esk(97).clm file in trials to verify its
successful conversion with the CreateClimate.exe module all of them where
disappointing and none would prove that we could use this file for the
simulation. Since this file was created after a long and arduous process we
tried to identify the problem by making variations of the Esk(97).clm file and
checking for mistakes on the creation and the conversion of the latter in
different stages and the signs would prove that upon the CreateClimate.exe
module was immolating the data from the Eskdalemuir1997Final.csv into the
Esk(97).clm file. That was an imponderable and unexpected occurrence that
left us no other choice that to drop the actual conversion and accept the
build-in climate databases that MERIT occupied to run the simulation. Of
the two possible choices for the final selection (Kew.clm and Glasgow.clm)
there is none that can satisfy the requirement for a realistic simulation and
there is no obvious way of making up assumptions this time to defend any
of the two files. It is clear that this time a more important compromise
would have to be made that would allow us to continue this project or to
terminate it. Since the second choice is not acceptable we need to accept to
run the simulation even with a climatic file from a totally different area and
time and to try to derive technical results for the aims and objectives of the
project following this critical compromise that they would not be based at
all on the sensitivity of the weather. Paragraph 3.1.5.1 has the final details of
the final selection between the two candidate files.
4.2 Scenarios- Results Analysis

The two scenarios devised were a mixture of knowledge, mathematical
guidelines and intuition. Their technical shaping was progressively
established to describe the two possible situations of energy distribution at
the Eco-Village and by the energy demand and supply signatures their
matching would prove their applicability. At the end it was MERIT that
decided if our actions were valid by approving or disapproving their
integrity.
4.2.1 Software Elucidations

Since the analysis of this project is based upon a software simulation
processing, the problems of compatibility, between the operating system
(OS) and the software version on one hand, and software vigorousness, in
125
terms of “bugs” on the other, were to apply in this analysis to the extend of
influencing some decisions and selections.
In more details the newest version 2.2 in the author’s computer could
not perform vital operations like the very important “Saving Project”
represented by one of the right-hand-side-column buttons in the Main
Program Window (See P.3.3.1). It would be really inapprehensible to try to
move on any further since this very essential operation was not occurring.
Had we moved on though, we would have fallen onto more of the
aforementioned problems just enough to make our life even harder than
what we already were experiencing. With some special arrangements we
managed to save some files into the directories of MERIT but this time the
“Open” operation in the “File” menu would not work. At this point we
abandoned any more experimentation with the v.2.2 and we thought that if
we could work the “CreateClimate.exe” component/program we might be
able to use it with the v.1.1 of MERIT and proceed in this way. But things
did not went as we hoped once more; the conversion of the created climatic
file was not succeeding and that the reason to exclude it from the
simulation. In spite of these algorithmic problems though, that prevented a
thorough utilisation of that version, v.2.2 had a much better inventory for
REST, updated and with more combinations available, so this is were we
would get the electrical demand profile for the Scenario 1. Version v.1.1 may
was much more stable but that did not mean that it was impeccable. In the
“Match and Dispatch” platform (See P.3.3.1) for the main phase of Scenario 1
(see below P.4.2.2.1) it would not save any of the graph data that were
produced during that experiments resulting in insufficient experiments
exhibits for the readers to assess for themselves these experiments. Apart
from that minor problem, there were no other serious problems on using
the program except a few crashes and freezes throughout the experiments
but nothing serious in the overall behaviour. But quite reasonably these
crashes could be a part of an interrelated nature of incompatibility problems
and not absolutely from MERIT part.
4.2.2 Scenarios Design- Result Analysis

For all the experiments (Attempts) of the two scenarios there was a Central
Guidance Panel (CGP) with 5 indicators that helped us proceed with the
experiments and reach the most appropriate results for an efficient
integration of REST with the Eco-Village energy demands. These indicators
are rendered in Merit’s last processing component (“Match and Dispatch”) as
we presented in P.3.3.1 and their value is reflecting a holistic assistance by
the software to the user to identify and scrutinize the selections of demand-
supply variations-combinations according to their relative importance to the
aims of the experiments. Had these indicators been inexistent there would
be no way to pick the right variations-combinations. In our case we used
these indicators differently for each one scenario. In Scenario 1 we gave a
126
weighted ordinance to them according to the aims of designing that
scenario, which was different from the ordinance that was assigned for
Scenario 2. The reason for doing such discrimination was to ascertain that
only justified trial and error variations-combinations were approved for the
final assessments. So for Scenario 1 we determined CGP-1 and for Scenario
2 CGP-2 respectively.
Table 4.1/ Central Guidance Panel

CGP-1 Requirements CGP-2 Requirements
1st . “Current Match” As high as possible with 1st . “Current Match” As high as possible with
minimum value of 5/10 minimum value of 5/10
2nd . “Potential Match As high as possible with 2nd . “Deficit”- à0
Rating” minimum value of 6/10 “Excess”
3 . “Deficit”-
rd <0 3 . “Inequality”
rd As low as possible
“Excess”
4th . “Inequality” As low as possible 4th . “Correlation” As high as possible
5th . “Correlation” As high as possible 5th . “Potential Match As high as possible with
Rating” minimum value of 6/10
4.2.2.1 Scenario 1
As we saw in P.3.3.2.1 Scenario 1 has two phases to completion. All the
experiments (Attempts) are described at Tables 3.14a and 3.14b for the PP
and Tables 15a and 15b for MP. In this paragraph we will explain all the
background analysis that followed each Attempt for PP in order to reach the
candidates for the MP and satisfy this design by another set of Attempts to
the final selection of efficient ReST numbers and combinations for a
satisfactory integration with the Eco-Village electricity demands. The PP has
the role of manifesting Attempts with the best CGP-1 indicators but as well
as the other will contribute to the best candidates the third one is the one of
extreme importance since it will illuminate the Attempt with enough energy
to charge the battery bank (BB) and is respected for that reason. Thus what
we will expect from any Attempts performed is to find one with the biggest
possible condition Deficit-Excess < 0 for all of the rest of indicators satisfied.
4.2.2.1.1 Preliminary Phase for Scenario 1
Attempt 1-PP
Beginning with Attempt 1 (experimental evidence can be found at Table
3.14a and 3.14b) we drew near the supply selection for Scenario 1 by
*
following the PEl1 value (P.3.3.2.1) and so selecting a single LMW-10KW
turbine for the first experiment as the theoretical value of the turbine was
*
close to the value of PEl1 . Following the ordinance for CGP-1 indicators
and from Table 3.14a and 3.14b we can see that the Current Match indicator
is really too low (4/10) and so since this is the first criterion in the CGP-1
127
we leave this Attempt. Moving on to the Attempt 2 the thought is that since
from Attempt 1 there is Deficit-Excess=35,328.43kWh>0 amount of energy(
See P.3.3.1) we should better increase the number of turbines to succeed
negative value i.e. more of Excess energy. Thus in this case there were two
LMW-10KW turbines for the supply.
Figure 4.4/ Power curves for the Demand and Supply of Attempt 1
Attempt 2-PP
Here the Current Match indicator is improved to 5/10 and the Potential Match
Rating is also improved to 8/10. Also the Deficit-Excess= 4,641.6kWh
difference is still positive but it is significantly decreased from the last
Attempt. As again as with the previous case we will perform Attempt 3 with
a further increase in energy supply which will be coming from three LMW-
10KW turbines.
Figure 4.5/ Power curves for the Demand and Supply of Attempt 2
Attempt 3-PP
128
The results in this case are in favour of an extremely large Deficit-Excess value
(-26,045.3kWh) and more importantly of negative sign which means that the
3rd indicator is satisfied. The 1st indicator is also satisfied (5/10) and so is the
2nd (6/10). From the 4th and 5th indicator examination we can choose upon
the next attempt. From CGP-1 we want 4th indicator to be as low as
possible or between Attempt 2 and 3 to decrease, but it was not and also the
5th to be low as possible but this was kept invariable. From P.3.3.1 we know
that the Inequality index symbolises the difference in the phase for demand-
supply profiles and so we hope that by the introduction of Photovoltaic
modules will be able to improve this difference. Another reason of why we
were to choose to introduce Photovoltaic modules and not a smaller wind
turbine for example is that the latter produces bigger vaults in the Deficit-
Excess values (for Attempt 2 it was: 4,641.6kWh and for Attempt 3: -
26,045.3kWh) and so with Photovoltaic units will help us to control better
the 4th index. Apart from the experimental actuation for introduction of
Photovoltaic units there are two other reasons for doing so. One is
stemming from the objectives of the project (for a backup system that
would secure PES from shutting down completely) and the other is simply
technical orientated since PVs are a very mature technology to be
overlooked. So how did we choose for any possible photovoltaic
combinations? First of all if we look back at Attempt 2 we will see that it has
a better 5th indicator according to that of Attempt 3. Thus we will use
Attempt 2 as the building block for a possible combination dock for
photovoltaic units. So
Deficit-Excess=4,641.6KWh and since
EEl M =66015.2 KWh
We want photovoltaic modules to cover at least a quarter of that energy for

a safe PES operation. Therefore:
EElM
E ElPhotovoltaics = + Deficit-Excess
4
Or,
E ElPhotovoltaics =21,145.75 kWh
And so the theoretical expected power from the photovoltaic modules will
be for one day:
*
PEl1 =2,413.8W
PV − Sc .1
129
From MERIT database we can choose two possible models that are the
BP130L and the SM110. These are the two top models in the range with the
highest efficiencies and power outputs. Briefly we can see some of their
characteristics in Table 4.2 below (more can be found in MERIT’s
database).
Table 4.2/ Technical Specifications for the PV modules

BP130L SM110
Nominal Efficiency 11.6% 12.66%
Open Circuit Voltage 36 21.7
Short Circuit Voltage 4.8 6.9
Number of Series Connected 72 72
Number of Parallel Connected 1 1
Power Output 130W 110W
So if we are to use these modules, and/or their multiples, then we need to

know how many do we need theoretically to configure Attempt 4. Simply
*
divide PEl1PV − Sc .1 by their power output and get: For BP130L =19 units and
for the SM110=22 units.
Figure 4.6/ Power curves for the Demand and Supply for Attempt 3
Attempt 4-PP
We initiated the combined PES experiments with BP130L, 19 from them,
to see how the previous values for indicators for Attempt 2 would behave.
Again Tables 13a and 13b have the details for selection parameters. The 1st
indicator was unchanged; the 2nd had a marginal increase of 1 point (9/10)
and the 4th and 5th were marginally improved according to the CGP-1
requirements. The 3rd indicator though had still not improved very much, as
130
was expected, from Attempt 2 (Deficit-Excess= 4,641.6kWh before vs.
2,707kWh now). So in a similar action to the first three Attempts we will
increase the number of photovoltaic modules until a dramatic, significant
change happens to the indicators.
Attempts 5 6 and 7-PP

In Attempt 5 we doubled the number of BP130L to 38 but still the same
trends were present for the 1st, 2nd 4th and 5th with an exception for the
Deficit-Excess energy difference fluctuating at -772.8 kWh, which was too far
away from the E ElPhotovoltaics value that we had theoretically defined previously.
So again for Attempt 6 we increased the number of BP130L to 76 and apart
form a change in the third indicator (Deficit-Excess= -3,096.9kWh) again all
other indicators were obeying a good potential swing but did not present a
significant change. Especially for the 1st and 2nd indicators the results for
Attempts 5 and 6 were static. Then in Attempt 7 it decreased to 8/10 and
this were we stopped the augmentation of BP130L finalising with 100 units.
From the last three Attempts we realise that the E ElPhotovoltaics as is required by
the theoretical hypothesis for a secure backup supply (from the photovoltaic
systems) will not be met unless we drop the 2nd indicator, which no such
violation is allowed from CGP.
131
132
Attempt 8-PP
For the penultimate experiment of this phase we did not follow the
augmentation procedure that we did in Attempts 5 to 7 and immediately we
set the number of SM110 models to 100 units. In this case the 1st and 2nd
indicators remained unchanged, the 3rd indicator was decreased from the last
attempt i.e. Deficit-Excess= -5,540.7kWh in Attempt 7 to Deficit-Excess= -
2,835.8kWh in Attempt 8 and reversely according to the CGP requirements.
Attempt 9-PP
133
Finally we increased the number of SM110 photovoltaic modules to 150
units to mainly check the response of the 1st and 2nd indicators to that action
but although the 1st remained constant at 5/10 the 2nd dropped to 8/10
from 9/10 that Attempt 8 scored.
As a recapitulation of the 9 Attempts of the PP we must consider the

CGP-1 so that we can select successfully the ones of relative importance to
the aims and objectives of the Scenario 1. These are no other than a realistic
operation of REST and a backup electrical system that will provide a safe
coverage for the Eco-Village for the largest possible number of days. Since
the best mark for 1st indicator has been 5 we can not sustain a choice for
any of the experiments. The discrimination will be based on the 2nd and the
3rd indicators. So we can justify the following Attempts:
• Attempt 3: It has the best results on the 3rd indicator and a moderate
result on the 2nd
• Attempt 6: It has a quite moderate result for the 3rd indicator and the
best possible on the 2nd
• Attempt 8: Same characteristics as Attempt 6.
4.2.2.1.2 Main Phase for Scenario 1

Obviously from what has been mentioned above the MP we will deal with
the introduction of batteries as an energy storage system to improve the
match results of the previous Attempts. Since in this case we do not care so
much about the “Potential Match Rating” of the experiments we will assess the
results of the MP experiments with the help of CGP-2 since this time the
134
“Deficit”-“Excess” energy is a much more important indicator for the overall
success of them.
The batteries that MERIT’s database has are Lead-Acid type of
batteries; the most commercia lly trusted and used cells for the last 30 years
Reference: IS-17
. These come with different voltages and currents specifications.
Our aim is to find the best possible battery bank (BB) for the Eco-Village
relative to the electrical energy requirements of the latter. This indicates the
fact that since the capacity of the BB will remain constant over the MP
experiments then for these experiments (modified experiments of the PP)
there will be different charging times according to their energy potentials as
described by the Excess indicator (Table 3.14a). The above argument is true
since the capacity of a BB is proportional to the product of the current,
which can provide to a load, to the time that it can do so ceaselessly and in
this case the discharging time will be fixed as well Reference: IS-18. Let’s have a look
at some numerical specifications for the selection of the BB. The Electrical
Energy for Scenario 1 (for the Eco-Village) is according to P.3.3.2.1:
EEl M =66,015.2 kWh

*
For the UK, the standard mains voltage ( VUK ) is fixed at 230Volts and so
the current that the REST will have to provide to the 17 houses of the Eco-
Village for 1 day (24h) will be:
*
PEl 1
IM1 = *
M
=32.76A… (Equation 4.1)
VUK
Where
EElM
*
PEl1 = =7,535.98W… (Equation 4.2)
M
365*24
So for the three attempts of the PP we can have, according to their Excess
values (Table 3.14a):
I Att3 =26.3A… (Equation 4.3a)
I Att6 =15.56A… (Equation 4.3b)
I Att8 =15.50A… (Equation 4.3c)
135
The capacity of the BB will be determined according to the following
relationship:
C=I*t Ah… (Equation 4.4)
We set a discharging span of 3 days or 72 hours. So in our case (Equation

4.4) will become:
CV 3 = I M 1 *72=2358.72Ah… (Equation 4.5)
So to find the charging time for the three cases we use (Equation 4.4), where
C= C V and I= I Att3 , I Att6 and I Att8

3
Therefore we have respectively:
t Att3 =3.75 days … (Equation 4.6a)
t Att6 = 6.25 days … (Equation 4.6b)

t Att8 = 6.25 days… (Equation 4.6b)
As a verification of these results we will use the Current Ratio (CR) and Day
Ratio (DR) conceptsDefiniton. These should come to equality if the time and
currents are calculated correctly. So for Attempt 3 CR=DR=0.8, for
Attempt 6 CR=DR=0.47 and for Attempt 8 CR=DR=0.48.
Now to define the size of the BB we need to incorporate a battery
from MERIT’s database to approximate the CV 3 by producing multiples of
its capacity. We chose the 215Ah@12V battery type and so the theoretical
numbers for the BB will be:
*
• 20 in Series= VUK =230V
• 11 in Parallel = CV 3 =2358.72Ah
Attempt 10-MP
This is the modified Attempt 3 from the previous phase. This time we
introduce the application of batteries to relieve the Excess energy that was
wasted in the previous experiment. So we choose 215Ah@12V batteries
with the theoretical combinations, as stated above, to see if there are any
differences in the real values of voltage and capacity. And there were! From
MERIT we get Nominal Capacity 1= 317.38Ah and Nominal Voltage
Definiton
CR=Discharge Current/Charging Current, DR=Supply Days for BB/Charging Days for BB
136
*
1=252.00V (very different from CV 3 and VUK ). So again by iteration we
approximated the theoretical values with the following combinations:
*
• 18 in Series ≈ VUK
• 191 in Parallel ≈ CV 3
For this analysis we must remember to use CGP-2 for the appellation of the
indicators! As we can see in Tables 13a and 14a by inspection of the
Attempt 3 and 10 results, the 1st indicator remained constant, the 3rd
indicator was reduced and the 4th was increased in a manner as required by
CGP-2. Also the 2nd indicator shows a decrease in its value from -26,051.3
to -21501.7 kWh respectively. MERIT suggests that with increased storage
we can get an 8/10 for the 5th indicator. We interpreted that as a prompt to
increase the BB capacity. It is not really important according to the
ordinance of CGP-2 to study the “Potential Match Rating” indicator any more
but since the suggested value is really tempting we decided to go with a
further increase in the BB capacity to find out if that hypothesis was true. So
for this case, if t=5 days and I= I M 1 then CV 5 will be equal to 3931.2Ah,
and so charging time for Attempt 10 will be t Att10 =6.25 days now. Again
with iteration we approximated the theoretical value for CV 5 and we got the
following combination:
*
• 18 in Series ≈ VUK
• 330 in Parallel ≈ CV 5
Attempt 11-MP
Here the 1st and 5th indicators remained unchanged, the 2nd indicator
decreased to -22,359kWh something that implies that more energy was
utilised from the BB and the 3rd and 4th indicators were following the
required inclinations in the manner dictated by CGP-2. Still MERIT
suggests an improvement for 2nd indicator with increased storage but we
consider such an action an unnecessary experiment since Attempt 10 is
already extended.
Attempt 12-MP
This is the modified Attempt 6 from the previous phase. Like before we
have introduced the application of batteries to relieve the Excess energy that
was wasted in the previous experiment. This is the first experiment for
137
which we get for the 1st indicator a value 6/10, above the average. The 2nd
indicator decreased from -3,096.9kW, in Attempt 6 to -51.6kW, in Attempt
12 which by far the best balance of Electrical Energy that we have seen so
far from all the experiments. The 3rd and 4th indicators were following the
required inclinations in the manner dictated by CGP-2. The 5th indicator
suggests again a further improvement in the match results with an increased
*
storage. So by following the same numbers for VUK and CV 5 as derived
from before we moved on to Attempt 13.
Attempt 13-MP
Here the 1 st indicator remained constant but the 2nd increased to -768.1kWh.
Truly the 3rd and the 4th indicators did improve from Attempt 12.
Attempt 14-MP
This is the modified Attempt 8. This experiment showed that it exploited
well the excess energy since the 2nd indicator fluctuated around -236.8kWh
relative to the -2,835.8kWh of the previous experiment. Again the 3 rd and 4th
indicators were following the required inclinations in the manner dictated by
CGP-2, and presented an improvement compared with the values of
Attempt 8. Similarly to the previous Attempts we again increased the BB
capacity since the 5th indicator was promising a further improvement in the
matching of the demand-supply electrical profiles.
Attempt 15-MP
Here the 1st indicator remained, as expected, constant and the 2nd increased
to -450.4kWh. Truly the 3rd and the 4th indicators did improve from Attempt
14.
4.2.2.2 Scenario 2
Contrary to Scenario 1 this one has only one phase since in this case we do
not require the introduction of BB for the recovering any of the energy
from REST. So we will use CGP-2 to assess the results for the experiments
of this scenario. A complete record of the experiments (Attempts 16-23) can
be found at Table 3.18.
Attempt 16
For the supply modules, as in Attempt 2, we implicitly used two LMW-
10KW turbines for this experiment, since comparatively the precondition of
using one turbine was proved (Attempt 1) that it was insufficient for the
electrical supply of EElV never mind the ED value that we have to cover
here, which is double that value. So from Table 16/Chapter 3 we can see the
138
1st indicator is a moderate result (5/10) and the 2nd corresponds to a residual
energy levelling (to the value of ED ) of -61,374.1kWh. Thus we increased the
number of turbines to four.
Attempt 17
In this case we got for the 1st indicator an unchanged results and for the 2nd
a slightly improved number of -9,252kWh. The 3rd and 4th indicators were
slightly changed and the 5th suggested a potential improvement to 8/10.
Although we know from past experience (Attempt 3) that in order to
control the value of the 2nd indicator effectively, for small fluctuations
(<5,000kWh), the use of PV modules is suggested still in increased the
electrical supply by raising the number of turbines to five.
139
Attempt 18
Here the 1st indicator was still constant and the 2nd was not satisfied at all
since its value was greater than zero something that was against the
requirements of the CGP-2. So as we did in Attempt 3 we will introduce
photovoltaic modules for a possible combination with the four turbines
from Attempt 17. Again as in Attempt 3 we start with the theoretical
orientation for the numbers of photovoltaic units and through experiments-
iterations we will try to find the best number according to the requirements
from CGP-2. So from Attempt 17:
Deficit-Excess=9,250.6kWh
*
PEl1 =1056kWh
PV − Sc .2
The model this time will only be BP130L to stay in conformity with the
previous actions and their theoretical numbers will be: For BP130L =8 units
and for the SM110 =10 units.
Attempts 19, 20, and 21

In these three experiments there was gradual increase in the 2nd indicator
from 8,436.1 to 7,723.2 to 5,177.6 compared with the 9,250.6kWh of
Attempt 17 and the 3rd and 4th indicators were following a gradual
improvement according to the inclinations of CGP-2. But the most
important indicator, 1st has not shown any improvement constantly set at
5/10 poor match result. At this point it was clear that to cover that
5,177.6kWh at the rate of 70kWh/Photovoltaic units we would need about
80 units eliminate that residual energy. In this case we know more or less
140
from the previous attempts that nothing will change in the matching results
and so it was verified by an unrecorded experiment. So if this was the case
how could we check if there were any other modules that could have a
different impact on the match results? The answer lies at the turbines power.
There is no need to use a large turbine for such small energy spans but
surely a smaller turbine could do the job. From MERIT’s database we
recalled the 3kW turbine and that is what we combined with the modules
from the last attempt.
141
Attempt 22
The 1st indicator did not change but the 2nd became negative (-4,682.6kWh)
to violate the requirement of the CGP-2 for that index. We can also see
opposite fluctuations for the 3rd and 4th indicators according again according
to the requirements of the CGP-2. This experiment did not live up to our
expectations of a better matching result and so we would need to reduce the
number of photovoltaic modules to 20 units to satisfy the 2nd indicator.
142
Attempt 23
Again the 1st indicator did not change from the last 6 attempts and the 2nd
did fail to improve. The 3rd and 4th indicators also showed unfortunate
results contoured reversibly from what the CGP-2 dictates.
143
End of Chapte r 4
144
Chapter 5-Conclus ions
The results of a project are to be digested after their analysis according to a pattern of accentuated fundaments.
These fundaments are the true reason of contemplating and studying and the reason for researching a subject so
vocaciously. All of the work must be imparted to the readers as practical upshots that can be used for discussion
and further research.
5.1 Aims Attestation

In this project there is a slight difference between the aims and the objective
of this study. We decided that it would be better if give to the aims a more
generic character about the purpose of establishing this study and to the
objectives a more specialised character. As we have mentioned before both
of them are bonded to a certain type of Requirements/Guidelines, which
are in mathematical words are the Boundary Conditions (BC) for the
experiments:
R1: “The Eco-Village has to be energy-wise supported by sustainable

technologies only”.
R2: “The Eco-Village must be autonomous to any biological, physical

and energy requirements”.
R3: “The simulation must be a realistic model of the actual dynamic

relationships of energy demands to the area of development and the
community size and character”.
5.1.1 Aim-I: Identify the Potential Use of MERIT in the

Integration of REST for the Tweed Valley Eco-Village.
The first aim of this project is about the program itself which we had to use
to succeed the study for the integration of REST for the Eco-Village. This
software belongs to category of programs that the author refers to as
CoSiMReTsI or Computer Simulation Methods for Renewable Technologies
Integration and as the rest programs of its family their aim is to provide
invaluable assistance when planning with renewable technologies for the
provision of energy for a variety of applications (from a single house to a
large community). All these programs facilitate the engineers with time
effective dynamic simulations that would take otherwise, with conventional
means of planning, multiples of the time scales that these programs can
succeed.
We had the pleasure to work with one of these little “scouters” to
help us complete this study for the Tweed Valley Eco-Village project and
145
the only remarks that we can make are no other but admiration and support
for this amazing concept. It would be really almost impossible to arrange
hundreds of equations with several parameters in each one of them to
produce realistic results about the use, flow, distribution and magnitude of
energy requirements of a dynamic entity. Since the beginning of the project
it was quite obvious that this program would be the best facilitator that we
could ask for under the sun. One of the characteristics of MERIT is the very
illustrative and concise environment-interface that the user navigates
between the three-phase control platforms (preliminary, middle and
simulation) and inside them once they are selected (See P.3.3.1). But where
MERIT was really proved an excellent assistant was at the point when we
had to simulate the Electrolyser demand in kWh according to the Fuel Cell
seasonal Operational Modes (OM) and of course at the simulation part of
the two scenarios (Scenario 1 and 2) where it was incredible the ease by
which we could iterate between the experiments (Attempts) to approximate
the required values.
As all computer programs MERIT did appear to have some
shortcomings (these did not objectively verified by other sources to provide
a complete assessment factor) that hindered the possibility of a greater
success of the project; concerning Aim-II below. The version v.2.2 did not
correspond well at the specific computer (OS and other applications) and
did not rise to the full expectations of what we might have though that
could offer in the opposite case. The newest version is clearly much more
advanced than the first one including the all essential component-program
“CreateClimate.exe” that would allow us to use the weather data, arduously
searching for over two months, so that we could achieve a much feasible
simulation for the Thornylee forest area. Unfortunately this component did
not work successfully no matter how many different performances we
applied on the critical file to be converted and how much advice we seek
from academic staff of the University of Strathclyde. It also was superior to
the less developed oldest version v.1.1 database-wise since it included energy
carriers such as hydrogen, had much more up-to-date renewable
technologies such as fuel cells and finally more realistic profiles for
electricity and thermal energy demands in the UK (including the one that we
used for the Scenario 1 experiments. Version v.1.1 was much more stable in
terms of partial and greater vital operations such as “saving” and “opening”
although it did present quite frequently a few crashes
5.1.2 Aim-II: Identify the Potential of Thornylee Forest as a

Development site for the Eco-Village.
This aim was unfortunately not verified through the analysis of this project
and maybe this could be the biggest loss amongst the ReST of the aims
since it is considered to be by the author the backbone of the study. It is
obvious that that if the critical conversion of the climatic file was successful
146
(See P.3.1.5.1 and P.4.3.1) then we would have a good reason to talk about a
potential use of the Thornylee Forest although the simulation would refer to
a weather profile for a slightly expanded and remote area than the forest
itself (See P.3.1). In engineering intellection someone would rather have a
rather good approximation of a field of study than none whatsoever, as in
this case. We can not speak of the potential of the Thornylee Forest since
the climatic profile is referring to Glasgow which is too far away from that
area and has no conformity with the assimilation assumptions that we set in
Chapter 4 (P.4.1.1.1 and P.4.1.1.2) but to approximate the energy simulation
we tried to embrace a reasonable replica of the Thornylee Forest at the
Eskdalemuir location. So it is a bit of a disappointment that this aim did not
come to a conclusion as this could be possibly used as an extemporaneous
planning for the villagers in case of considering the same PES and SES as
this project did (sorry folks!).
5.1.3 Aim III: Identify the absolute Matching of Demand and

Supply energy Requirements for the different Solutions
examined under the Condition of an Autonomous Eco-
Village.
If we detach the location, on which this project is readily applied (Glasgow),
from the actual simulation then we can focalise on the numerical and
statistical matching results of the Energy requirements for the Eco-Village
rotating around the demands and supply methods of the two Scenarios. As a
quick reminder Scenario 1 was an absolute Electrical study with Wind
Turbines and Photovoltaic technologies as Primary Energy Supply (PES)
and Batteries utilisation as a Secondary Energy Supply (SES) and Scenario 2
a combined Electrical and Thermal study (CHP study) with the same PES
and a Fuel Cell module as SES comprising an Electrolyser, a Fuel Cell and a
number of pressurised fuel Storage Tanks units (See P.3.2.1).
Scenario 1
For Scenario 1 only the Main Phase (MP) is of relative importance to the
current aim examination; the Preliminary Phase is a selection stage for the
candidates of the MP (See P.3.3.2.1 and P.4.2.2.1). Referring to P.4.2.2.1.2
for the MP we conducted 6 experiments (Attempts 10-15) which we are
going to evaluate with the help of the Central Guidance Panel (CGP-See
P.4.3.2). For the MP of Scenario 1 we will use the weighted evaluation
ordinance as directed by the CGP-2. According to the requirements of that
panel the 1st indicator must be satisfied before other indicators are
examined. In that way Attempts 10 and 11 are disqualified since they are
below the average score of the rest of the Attempts: 5/10<6/10 (See Tables
3.15a and 3.15b). So we are left with 4 Attempts. For these now we need to
assess them according to the 2nd indicator of CGP-2, the requirement for a
147
balanced energy flow to the Eco-Village or in simpler words the balance
between electrical energy demand of the community (in a year of operation)
and the electrical supply from Renewable Supply Technologies (ReST) for a
normal and undisturbed electrical vitality. Again from Tables 3.15a and
3.15b we can see that the more successful experiment is Attempt 12 as this
satisfies the condition of 2nd indicator (“Deficit-Excess”=-51.6KWh) with
Attempt 14 following with a value of 236.6KWh. In the first case the
difference is negative which shows a slight ascendancy of excess energy
supply over the demand scale and corresponds to an implicit predominance
over the second case in which the difference is positive. We are certainly in
favour a positive stock of energy than any deficit amount that is against the
2nd indicator but the second case is closer to a more balanced value. So the
choice will depend on the rest of the indicators for a final selection. So for
Attempt 12 the 3rd and 4th indicators are 0.3336 and 0.4906 respectively and
for Attempt 14 are 0.3336 and 0.4904 respectively. Thus a direct choice
cannot be made from these conditions and neither can be form the last
indicator (5 th ) since both experiments have a potential score of 10/10 with
“Increased Storage” according to MERIT. It is thus a conclusion that both
Attempts were successful according to the current specifications for the
electrical coverage of the village. The SES in this case i.e. the Battery Bank
(BB) will provide enough electrical energy for running any loads in the Eco-
Village within 3 days, maximum charging-discharging cycle occurrence, after
which it will be completely discharged.
Obviously a “Reasonable Match” of 6/10 is just satisfactory but we
have to remember that this simulation really corresponds for Glasgow and
not for Thornylee Forest where the winds would be expected to be much
more stronger (according to the British Wind Energy Association Glasgow
has an average wind speed of around 6-7m/s whereas the area around
Thornylee Forest is 9-10m/s-See Figure 6/Chapter 3) and maybe the solar
radiation would be likewise increased respectively. So such a result is not
depressing at all and is considered a valid argument to say that if the
autonomous Eco-Village where to be situated at Glasgow it would most
likely support an electrically self-sustained community. MERIT suggests an
even further improvement for a potential match between demand and
supply but surely the experiments here (Attempts 13 and 15) showed an
opposite case. We don’t know exactly where this increased storage is
referring to but we suspected that maybe it has a connection with other
forms of storage for the village. It was made clear that this was true from an
unofficial number of experiments upon these two Attempts that if
combined with say with “Grid Connection” the matching results were rocketed
to 8/10. Obviously in this case we cross the requirement for an autonomous
village (R2) so this was the best compromise with BC of the project.
148
Scenario 2
For Scenario 2 we need to look at Attempts 16-23 to deduce any results for
the satisfaction of Aim-III. Again we are assessing their results with
weighted evaluation ordinance as directed by the CGP-2. In this scenario we
have 8 potential experiments to choose from the best match results between
the Electrical and Thermal demand of the Electrolyser and that arising from
the PES. The difference between this scenario and the previous one is in
terms of the actual demand quality for the simulation the latter being not
directly the demand of the Eco-Village itself but its modified form
translated for the needs of the Fuel Cell and its inherent component the
Electrolyser (See P.4.2.2.2). Here all the Attempts exhibited a very modest
match result of 5/10 for the 1st indicator of CGP-2. This is quite
discouraging since the requirement of the 1st indicator is for a minimum
value of 5/10 leaving all these attempts out of the game. Or is it not? A
“Poor Match” is simply MERIT’s user-software interaction method to warn
the user for more energy storage in terms of auxiliary storage media that it
possess. In our case we did not respect at this recommendation and so we
got rather disappointing results. But if we compare the graphs of P.4.2.2.2
and the results of the Table 3.18 we will see that the 2nd indicator is well
satisfied by most of them and that is a good identification element of the
possible success amongst some of them. More specifically Attempt 23 was
much more closer to a energy balance than any other experiment (-
2,646.1KWh) and since these kWh are of a negative sign it simply means that
the village will not utilise this energy by any other storage technology and
this is why MERIT is rating it with a “Poor Match” indicator. But in real
terms what would happen is that the Electrolyser would be fully run by PES
and so would be the Fuel Cell. Thus the cycle of energy flow would be
satisfied. The 3rd and 4th indicators are also very gentle with Attempt 23 as
the latter has the best ratings for these two against all other Attempts.
Finally the 5th indicator looks quite well since the potential of this Attempt
could reach theoretically a 9/10 excellent match by capturing all the excess
energy. All these facts testify that Scenario 2 was successful in matching the
electrical demand of the Electrolyser.
5.2 Objectives Attestation
5.2.1 Objective I: Assess the Use of a Fuel Cell Module as a

Provider and Storage Solution of Renewable energy for the
Eco-Village with respect to Sustainability requirements.
It is really difficult to assess the Fuel Cell Module since it was not an
experimental aim of this study to directly examine and talk about any
tangible results so we can only talk about the actual selection of it as a CHP
method to provide and store energy for the Eco-Village. There is a large
149
antagonism out there for CHP solutions the more known being a CHP with
diesel generator(s) to achieve the required power outcomes and a more
synchronous choice would be micro-turbines not a bad solution for large
energy projects such as this Eco-Village. But it would be really a violation of
the very first of the BC of the project (R1), for R1 is requiring only
sustainable solutions to any of the technologies selected for PES or SES.
Thus the Fuel Cell Module would prove the only green and sustainable
choice in our case.
The Electrolyser was a market model that could produce around
60 Nm / h of hydrogen fuel at an energy feeding cost of 5kW/ Nm3 and a rate
3
of 1lt/ Nm3 or 0.001 m 3 / Nm3 . At this H 2 production rate it sufficiently

connected in series with the Fuel Cell itself which required in the best of the
cases 3.93 Nm 3 / h for OM 3 and in the worst 11.80 Nm 3 / h at OM 2 . In any of
the cases it seems that there is a large safety margin between these two
values and the maximum fuel flow the Electrolyser can provide for the Fuel
Cell. That brings us to the question of how we will exploit all the wasted
hydrogen fuel. As we saw in P.3.2.2.2 this was going to be channelled to a
number of low pressure tanks 5 for the small charging cycle (1 day) and 10
for the large one (2 days). To ensure that the hydrogen tanks are always
charged the study was such that allowed this consideration by the
application of larger PES units. For the practical case of installing such a
module a Fuel Regulator (FR) device could be used that could control the
flow of hydrogen gas to the storage vessels and stop the process by
deactivating the Electrolyser from the village grid so that electricity from
PES could be arranged and utilised in a different way. Instead of that and
according to future changes in the structure of transportation the excess
hydrogen could be even used, under specific modifications i.e. larger
pressure and change of composition (liquid), for topping up hydrogen
vehicles or just for selling purposes to a chemical company or a hospital,
oxygen gas is also attractive in this case for its high purity.
Thus the Fuel Cell module would cover the electrical and heating
demand of the Eco-Village very satisfactorily according to the theoretical
numbers of this study and it is simply the most sustainable option that
someone can select to grand these demands. In our case the Fuel Cell was to
be chosen at 25kW power output at 100% of its operating range. This
would allow an unstressed operation for any of the three operation modes
(OM) on a continuous working pattern. For any future expansion of the
Eco-Village since the fuel cells are modular devices we can simply add
another module, of an appropriate power value, in series or in parallel to get
the energy we need. The positioning of the Fuel Cell Module is thought to
be at a central point in the community area with power lines and gas pipes
stretching in a web-like form to all of the houses (17) to provide the
necessary electrical and thermal energy. It is considered that to avoid the
150
unnecessary cost and installation and maintenance operations on gas pumps
and gas pipes for the hydrogen fuel the Electrolyser should be situated at
the same control room as that of the rest of the units will be it, Fuel Cell and
Storage Tanks. Finally in order to decrease the cost of the installations the
FC plant could be connected to the grid for the time that produces excess
electricity and so an appropriate selling or even exchanging of this extra
power to the grid could be arranged that would economically boost the
financing of the plant acquisition.
151
End of Chapte r 5
152
Chapter 6-Limitations an d Fu ture Research
No project is conducted without problems, misadventures or misfortunes and this study is certainly one of these.
There were many obstacles in trying to find the appropriate information and in trying to apply it in practice to get
results. This would lead to incoherencies and discrepancies that need to be examined by future workers.
6.1 Climatic Limitations

• For retrieving the necessary weather parameters we had to look at a
variety of databases over the internet until we finally spotted the most
appropriate one (PWD). This was a time intensive process,
approximately two months for the selection of a satisfactory database.
• The inexistence of a station at the area of study (Thornylee Forest)
was a big obstacle to readily identify the critical weather parameters
for the simulation and so approximations were followed to bypass
that problem that disturbed the true values for that area. In future
work someone would have to monitor the area for a minimum of two
years for these weather parameters, especially for wind values since
the radiation could be assimilated by nearby stations of the BADC
database.
• The geographical examination of the weather stations was a very
difficult process since their distances from the Thornylee Forest had
to be calculated according to valid map scales and in the case of
applying assumption three (A3) to some of them a further
identification of morphological maps of Scotland had to be retrieved.
• The database files on which the Evaluation and Formation stages
(P.3.1.4 and P.3.1.5) were conducted had a lot of missing values that
hindered the process of a more robust analysis.
6.1 Technical Limitations

• It has been stated a number of times so far that the conversion of the
climatic file was not possible since the “CreateClimate.exe” did not
work. Had this conversion been successful we would have run the
simulation on a truer and realistic basis and so the results produced
would have been much more authentic. In future work it is necessary
that a real climatic profile is made for the simulation as this enable the
engineers to predict the behaviour of PES to a more realistic extend
and thus the feasibility if the project will be much clearer.
• For the Selection of Power Plant (P.3.2) we had a numerous
problems in identifying the most appropriate type of Electrolyser,
Fuel Cell and Storage Hydrogen Media. For the Electrolyser we had
to identify a model that not only could it provide the FC with the
CFC but it would produce that hydrogen fuel at the necessary
pressure conditions and it would only use fresh water as its fuel. The
153
electronic correspondence was not many times successful and so no
technical specifications could be retrieved. The same problems we
faced on trying to identify a proper FC and Storage Hydrogen Media
modules. The theoretical approach was thus necessary to determine
the numerical guidelines for assembling the FC plant.
• In Scenario 1 we had to approximate the annual demand of the Eco-
Village with a profile from the MERIT’s database. In version 1.0 this
was not possible and only with an appropriate maneuver did we
manage to overcome this problem.
154
End of Chapte r 6
155
Referen ces
Literature Exhibits
LE-1. Marina Fischer-Kowalski (1997). Gesellschaftlicher Stoffwechsel und
Kolonisierung von Natur. Amsterdam.
LE-2. I.G. Simmons (1989). Changing the Face of the Earth. Culture,
Environment, History. Oxford 1989, 379.
LE-3. Marina Fischer-Kowalski and Helmut Haberl (1997). Tons, Joules
and Money: Modes of Production and Their Sustainability Problems In
Society and Natural Resources. 1997, 10, 70.
LE-4. Grove, Richard H. (1995). Green Imperialism: Colonial Expansion,
Tropic Island Edens and the Origins of Environmentalism. Cambridge
1995, UK: Cambridge University Press.
LE-5. R.P. Sieferle (1997). Rückblick auf die Natur. München. Database
1997, 155-158.
LE-6. United Nations Environment Programme / Global Environment Outlook
2000
LE-7. Brown Paul (1996). Global Warming: Can a Civilization Survive?
Blandford, London.
LE-8. Kaufman, Donald G. and Cecilia M. Franz (2000). Biosphere 2000:
Protecting Our Global Environment. Kendall/Hunt Publishing Co.,
Dubuque, Iowa.
LE-9. Wilson, Edward O. (1999). The Diversity of Life. W.W. Norton &
Co., New York.
LE-10. Tilman, David (1999). The ecological consequences of changes in
biodiversity: a search for general principles. Ecology 80(5):1455-1474.
LE-11. Goldsmith, Edward, R. Allen, M. Allaby, J. Davoll, and S.
Lawrence (1972). Blueprint for Survival. Houghton Mifflin Co.,
Boston.
LE-12. Brown, Lester R. (1981). Building a Sustainable Society. W.W.
Norton, New York.
LE-13. World Commission on Environment and Development (1987).
Our Common Future Oxford University Press. Oxford 1987
LE-14. United Nations Conference on Environment and Development.
(1992). Agenda 21: Programme of Action for Sustainable Development.
United Nations Department of Public Information, New York.
LE-15. Robinson, John and Caroline Van Bers. (1996). Living Within Our
Means: The Foundations of Sustainability. David Suzuki Foundation,
Vancouver, BC.
LE-16. Costanza, Robert, R. d'Arge, R. deGroot, S. Farber, M. Grasso,
B. Hannon, K. Limburg, S. Naeem, R.V. O'Neill, J. Paruelo, R.G.
156
Raskin, P. Sutton, and M. van den Belt. (1997). The value of the
world's ecosystem services and natural capital. Nature 387: 253-260.
LE-17. Francesca Jane Born (2001). Aiding Renewable Energy Integration
through Complimentary Demand-Supply Matching. PhD Thesis.
Strathclyde University.
LE-18. Osborne Dariane (2000). The Relationship between the Increase in
Computing Power and the Development and Adoption of Renewable Energy
Technologies.
LE-19. Clarke J.A. and Grant A. D. (1996). Planning Support Tools for the
Integration of Renewable Energy at the Regional Level. WREC 1996.
LE-20. Jones P. J., Vaughan N. D., Sutcliffe A. and Lannon S. (1996).
An Environmental Prediction Tool for Planning Sustainability in Cities.
4th European Conference on Architecture, 26-29 March 1996,
Berlin Germany.
LE-21. Energy Efficiency and Renewable Energy Network (EREN-f),
US Department of Energy, RETScreen, 2000,
LE-22. Castro M.A., Caprio J., Peire J. and Rodriguez J.A. (1996).
Renewable-Energy Integration Assessment Through a Dedicated Computer
Program,. Solar Energy Vol. 57, No.6, pp471-484, 1996
LE-23. Ramakumar R., Abouzahr I., Ashenayi K. (1992). A Knowledge-
Based Approach to the Design of Integrated Renewable Energy Systems.
IEE Transactions on Energy Conversion, Vol. 7, No. 4,
December, 1992.
LE-24. Energy Efficiency and Renewable Energy Network (EREN-a),
US Department of Energy, ASEAM, 2000.
LE-25. Energy Efficiency and Renewable Energy Network (EREN-b),
US Department of Energy, Energy-10, 2000.
LE-26. Energy Efficiency and Renewable Energy Network (EREN-d),
US Department of Energy, DOE-2, 2000.
LE-27. Energy Efficiency and Renewable Energy Network (EREN-c),
US Department of Energy, ESP-r, 2000.
LE-28. Sir Julius Vogel (1889). Anno Domini 2000 or Woman’s destiny
(colonial edition) Hutchisons, London. 1889.
LE-29. Samuel Butler(1972). Erewhon, or Over The Range (rev. edition).
Golden Press in association with Whitcombe & Tombs,
Auckland 1927.
LE-30. Edward Bellamy (1960). Looking Backward 2000-1887. New
American Library, New York. 1960
LE-31. William Morris (1995). News from Nowhere, or an epoch of rest (ed
Krishan Kumar) Cambridge University Press, Cambridge and
New York 1995.
LE-32. Context Institute (1991). Ecovillages and sustainable communities: a
report for the Gaia Trust Context Institute. Bainbridge Island,
Washington. USA. 1991
157
LE-33. Cuming P. & Francis R. (1999). Design for Human Settlement-notes of
an advanced designer course. Permaculture Education Nimbin NSW
2480, Australia. 1999.
LE-34. Kathryn McCamant and Charles Durrett. The 3rd North
American Cohousing Conference in Seattle, September, 1997
LE-35. Tweed Valley Ecovillage Project Overview. March 2002
LE-36. Angelos Mademlis. Wind And Hydro Power System For The Tweed
Valley Ecovillage. September 2002. MSc Thesis. Strathclyde
University.
LE-37. Dincer I. (1999). Environmental impacts of energy. Energy Policy, vol.
27, July.845-854.
LE-38. World Bank, World Development Report (1992)
LE-39. Markvatt (2001). Solar Electricity. John Willey and Sons, LTD.
LE-40. Godfrey Boyle (1996). Renewable Energy- Power for Sustainable
Future. Oxford University Press.
LE-41. Zinger, D. S. and Muljadi, E. Annualized Wind Energy Improvement
Using Variable Speeds. IEEE Transactions on Industry
Applications. Vol. 33, no. 6. November-December 1997, pp.
1444-1447.
LE-42. Hoffmann, R. and Mutschler, P. The Influence of Control Strategies on
the Energy Capture of Wind Turbines. 2000 IEEE Industry
Applications Society Annual Meeting, Rome, 8-12 October,
2000.
LE-43. Slootweg, J. G., Polinder, H., and Kling, W. L. Dynamic Modelling
of a Wind Turbine with Direct Drive Synchronous Generator and Back to
back Voltage Source Converter and its Controls. 2001 European Wind
Energy Conference and Exhibition. Copenhagen, Denmark. 2-6
July 2001.
LE-44. Slootweg, J. G., Polinder, H., and Kling, W. L. Dynamic Modelling
of a Wind Turbine with Doubly Fed Induction Generator. 2001 IEEE
Power Engineering Society Summer Meeting, Vancouver,
Canada, 15-19 July 2001.
LE-45. Fuel Cells for distributed generation: A technology and marketing summary,
USDOE 2000.
LE-46. A.J. Appleby, F.R. Foulkes. Fuel Cell Handbook, Van Nostrand
Reinhold, New York, NY.1989.
LE-47. Fuel Cell Handbook, Fifth edition, USDOE, Office of Fossil
Energy, 2000 and cogeneration”, USDOE 2000
Internet Sources
IS-1 http://www.runet.edu/~wkovarik/hist1/timeline.new.htmlgdfgfd
IS-2 http://www.eeexchange.org/sustainability/Intro/outline.htm
IS-3 http://library.thinkquest.org/26026/index.php3
158
IS-4 http://www.pbs.org/now/science/unenergy.html
IS-5 http://gen.ecovillage.org/index_body.html
IS-6 http://www.esru.strath.ac.uk/Courseware/Merit/index.htmgdfgd
IS-7 http://www.ecn.ac.uk/dfg
IS-8 http://badc.nerc.ac.uk/home/df
IS-9 http://www.eere.energy.gov/buildings/energy_tools/energyplus/c
fm/weatherdata_int.cfmfddf
IS-10 http://www.metoffice.comfdg
IS-11 http://www.bwea.com
IS-12 http://www.fuelcelltoday.com/index/0,1967,,00.html
IS-13 http://www.hydrogenics.com/hypm.htm
IS-14 http://www.fuelcells.org/StationaryTechnical.pdf
IS-15 http://www.eere.energy.gov/consumerinfo/elecsource.html
IS-16 http://www.esru.strath.ac.uk/Courseware/Merit/index.htm
IS-17 http://www.automotive-technology.co.uk/support/batteries.htm
IS-18 http://www.wppltd.demon.co.uk/WPP/Batteries/Charging_Meth
ods/charging_methods.html
IS-19 http://ovis.khv.ru/eng/wind.html
159
Append ix A
Table 1/ Record of the stations reviewed for the Peeblesshire County

County Station Name .hwx .radt .wind
BADDINSGILL RESR x x x
BLYTH BRIDGE x x x
BONNYCRAIG FILTER STA. x x x
BRAWN S DOD x x x
COWDENBURN x x x
EDDLESTON x x x
FRUID DAM x x x
GLEN HOUSE, FETHAN VIEW COTTAGES x x x
GLENTRESS • x x
HALLMANOR HOUSE x x x
KINGLEDORES AUTO.STA. x x x
MENZION BURN x x x
NORTH ESK RESR x x x
PEEBLES x x x
PEEBLESHIRE PORTMORE RESR x x x
RACHAN x x x
SHIPLAW LOGGER STA. x x x
SKIRLING x x x
SKIRLING, HANNA HOUSE x x x
STANHOPE FARM x x x
STOBO CASTLE x x x
TALLA LINNS FOOT x x x
VICTORIA LODGE x x x
VICTORIA LODGE NO.2 x x x
VICTORIA LODGE NO.2 LOGGER STA. x x x
WEST LINTON x x x
WEST LINTON, WOODLEA COTT. x x x
WEST WATER RESR x x x
WEST WATER RESR NO.2 x x x
160
Table 2/ Record of the stations reviewed at the neighbouring Counties of
Peeblesshire
County Station Name .hwx .radt .wind
BOWHILL • x •
SELKIRKSHIRE
GALASHIELS • x x
AUCHEN CASTLE • x x
CHAPEL CROSS x x •
DUMFRIESSHIRE DUMFRIES • x •
ESKDALEMUIR • • •
MOFFAT, BRECONSIDE • x x
ABINGTON • x •
CAMPS RESERVOIR • x x
CARNWATH • x •
COATBRIDGE • x x
CRAWFORDJOHN • x x
DRUMALBIN SAWS • • •
DRUMCLOG • x •
LANARKSHIRE
EAST KILBRIDE • x •
GLASGOW, SPRINGBURN • x x
GLASGOW WEATHER CENTRE • x x
LANARK • x x
LANARK, DRUMALBIN • x x
LEADHILLS NO.2 • x x
MOTHERWELL, STRATHCLYDE PARK • x x
MIDLOTHIAN IN
BORDERS - - - -
BUSH HOUSE • x •
EDINBURGH, EAST CRAIGS • x •
MIDLOTHIAN IN EDINBURGH, ROYAL BOTANIC GARDEN • x x
LOTHIAN EDINBURGH, BLACKFORD HILL • x •
FORTH ROAD BRIDGE x x •
LEITH HARBOUR x x •
PENICUIK • x x
BERWICKSHIRE CHARTERHALL SAWS x • x
161
Table 3/ Local meteorological measurements for Bowhill and Eskdalemuir
areas (1994)
Bowhill-1994 (Dly3208.hwx) Eskdalemuir-1994 (SYNOP.hwx)
Dir Speed TCA Vis TEMP Dir Speed TCA Vis TEMP
1 250 9 5 4000 16 170 2 7 40 -22
5 140 5 8 200 3 80 9 8 1500 11
10 270 2 8 4000 29 310 2 7 1800 18
Januany
15 270 2 1 4000 1 350 2 2 2000 -19

20 290 13 8 1000 73 240 5 8 200 55
25 290 19 5 400 54 190 7 7 1800 23
30 290 24 6 1000 28 280 20 4 3000 23
1 230 13 6 1000 74 290 20 6 2500 58
5 20 13 7 1000 49 180 11 7 3000 17
10 230 5 8 1000 49 30 16 7 4000 41
April
15 360 9 7 1000 49 30 16 7 4000 41

20 230 2 7 1000 53 80 2 7 2500 58
25 180 5 8 1000 84 170 8 8 4000 58
30 230 5 8 1000 94 300 7 7 4000 81
1 230 5 4 1000 175 120 6 7 4000 170
5 200 5 2 1000 162 270 9 1 3000 152
10 0 0 8 1000 147 200 14 4 300 138
July
15 230 5 2 1000 144 360 9 4 5000 133

20 50 5 5 1000 202 210 5 3 1500 178
25 100 9 8 1000 159 200 9 8 800 138
30 180 2 4 1000 165 150 6 3 2000 175
1 0 0 8 1000 85 30 2 8 400 76
5 270 5 3 1000 88 190 6 6 3500 34
10 0 0 4 1000 58 170 2 3 10 51
October
15 0 0 8 200 108 290 2 7 180 88

20 180 2 8 400 104 120 6 8 1000 108
25 200 5 0 1000 76 220 7 8 1000 64
30 0 0 8 100 70 350 2 8 120 69
162
Table 4/ Local meteorological measurements for Bowhill and Eskdalemuir
areas (1997)
Bowhill-1997 (Dly3208.hwx) Eskdalemuir-1997 (SYNOP.hwx)
Dir Speed TCA Vis TEMP Dir Speed TCA Vis TEMP
1 20 9 6 1000 -4 0 0 7 4500 -14
5 360 9 7 1000 4 0 0 6 2200 -12
10 0 0 6 1000 11 0 0 7 2500 -5
Januany
15 0 0 8 1000 69 170 7 8 10 54
20 320 2 7 1000 16 0 0 7 6000 -8
25 320 5 8 400 9 0 0 8 120 10
30 230 0 0 1000 1 360 2 4 80 -4
1 140 5 7 1000 105 190 7 8 1200 78
5 230 19 8 1000 107 280 19 8 700 93
10 320 2 5 1000 104 310 9 3 4000 107
April
15 320 2 3 1000 79 50 5 1 2200 77

20 270 2 6 1000 60 240 2 7 4500 43
25 160 9 7 1000 74 70 13 7 2800 55
30 320 9 7 1000 121 240 9 7 2800 108
1 0 9 8 1000 82 340 2 8 800 78
5 200 0 8 1000 136 120 5 4 3500 142
10 230 2 9 20 159 180 2 1 1800 215
July
15 0 5 8 1000 154 200 3 8 800 132

20 290 0 0 1000 159 50 2 1 4000 204
25 200 9 4 1000 166 290 8 5 4000 145
30 270 13 7 1000 153 220 10 7 1500 137
1 230 24 6 1000 139 27 15 5 6000 132
5 230 19 4 1000 123 190 7 5 1200 103
10 230 9 8 1000 100 240 6 7 3000 85
October
15 50 2 8 400 75 360 2 8 500 72

20 50 5 7 1000 56 50 13 6 2800 53
25 20 0 4 1000 75 350 2 6 1200 18
30 230 2 8 1000 84 350 2 8 70 42
163

4

Uploaded by

Copyright:

Available Formats

4

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

4

Uploaded by

Copyright:

Available Formats

University of Strathclyde

Thesis in partial fulfilment for the degree of Master

Departmen t of Mechan ical Engineering,

Decla ration o f Author’s Ri ght

Chapter 2-Literature Review , 30

Chapter 4-Discussion, 118

Chapter 5-Conclusions, 145

Chapter 6-Limitations and Future Research, 153

Referen ces, 156

1.1 Civilisation and Environment-

1.1.3 Agrarian Societies

• Biotechnology. Energy radiating from the sun is primarily caught and

Energy use in agrarian societies has a general structure which can be

BC-1200 Reference: IS-1

1750-1830 (Enlightenment) Reference: IS-1

1.1.4 Transformation Society

1.1.4.1 The Turning Point- Industrial Revolution

1.2 Environmental Crisis of the 21st Century

1.2.1 Anthropogenic Climate Change

1.2.2 Depletion of Stratospheric Ozone

1.2.3 Loss of Biodiversity

1.2.4 Other Problems and Fut ure Threats

1.3 Sustainability, Ecology and Engineering

their own needs”

Table 1.2/ Ecosystem services and functions Reference: LE-16

For today’s “developing” sciences like engineering the challenge of

• Pollution prevention and waste minimization

Green Engineering is now a cross-disciplinary topic addressing a wide

1.3.2 The Dark Side of the Energy Industry

1.4 A New Spawn

1. It is an ongoing experiment in sustainable communal living where

Such ecologically-based communities on a village scale start small, mainly

1.5 Auton omous Energy Rendition and Renewable Energy

2.1 A Brave New World

• The Findhorn Foundation, Scotland.

Most of these projects are now internationally well recognised, while

2.1.1 Organizational and Design Principles

“Human scale, fully featured settlement,

He believes that to achieve a truly sustainable community it must have:

1. Conscious awareness of the interrelationships of all life and the cyclic

• The bio system challenge of integrating eco-village activities

Eco-villages attempt to meet these challenges by adopting design

• Human scale – of such a size and proximity that face to face

Clearly these are challenging principles and existing eco-villages are at

2.1.2 The Secrets for Green Practices

1. Participatory Process. Residents participate in the planning and design

• Reducing energy in use,

A green building places a high priority on health, environmental and

• Reduce human exposure to noxious materials,

1. minimising non-renewable resource consumption

Sustainable buildings have minimum adverse impacts on the built and

2.1.3 The Vision of the Tweed Valley Eco-Village

Figure 2.2/Thornylee Forest and surroundings

As a genuine representative of the Eco-Village movement the Tweed Valley

Figure 2.4/ Top of the Thornylee Hill

Figure 2.5/ Natural Reservoir

2.2.1 Photovoltaic Systems

Figure 2.6/ PV system components Reference: LE-39.

PV systems have several advantages: they are cost-effective alternatives in

Figure 2.8/ Roof Area (sfeet 2) as a function of PV capacity