Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 20 views

    Metrology Lesson Plan

    Uploaded by

    venky

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd

    Metrology Lesson Plan

    Uploaded by

    venky
    20 views4 pages

    Copyright

    © © All Rights Reserved

    Available Formats

    DOCX, PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    20 views4 pages

    Metrology Lesson Plan

    Uploaded by

    venky

    Copyright:

    © All Rights Reserved
    Download as DOCX, PDF, TXT or read online from Scribd
    Download as docx, pdf, or txt
    You are on page 1of 4

    GOKULA KRISHNA COLLEGE OF ENGINEERING-SULLURUPETA-524121

    Department of Mechanical Engineering

    LESSON PLAN::

    Academic Year : 20 Sem : I


    Course: metrology
    Class : III B.TECH Section : ME A&B
    Date of commencement of Class work : Date of end of Class work :
    Prepared By:MANNELI TALPAGIRI, Assistant Professor Approved By: HOD

    Lect Date (As per Actual


    ure Academic Topics to be covered Dateof Remarks
    No calendar) completion
    UNIT-I
    1 SYSTEMS OF LIMITS AND FITS
    INTRODUCTION:
    2 Normal size and tolerance

    3 Limits and deviation

    4 Fit-unilateral and bilateral tolerance system

    5 Hole and shaft basis system

    6 interchangeability

    7 Deterministic and statistical tolerance.

    8 Selective assembly

    9 International standard system of tolerance


    10 Selection of limits for correct functioning
    11 Selection of tolerance for correct functioning

    UNIT-II
    12
    LINEAR MEASUREMENT: Length standards

    13 End standards
    14 Dial indicators

    15 micrometres

    16 Different methods of angles

    17 Bevel protractor
    Angle slip gauges
    18
    Angle dekkor
    19

    20 Sprit levels

    21 Sign bars
    22 Sign table
    23 Rollers used to measure angles and tapers
    24 Spheres used to measure angles and tapers
    25 Taylor’s principle

    26 Design of go and no go gauges


    27 Plug and ring

    28 Snap ,gap and taper

    29 Profile and position gauges


    UNIT-III
    30 OPTICAL MEASURING INSTRUMENTS: Tools
    maker microscope and uses

    31 autocollimators

    32 Optical projector

    33 Optical flats and uses

    34 Interference of light

    35 Michelson’s interferometer

    36 NPL flatness interferometer


    37 NPL gauge interferometer
    38 Revision
    39 Revision
    40 Revision

    41 Revision

    42 Revision
    Revision
    43
    Revision
    44

    45 Revision

    46 Revision

    47 Revision

    MID EXAMINATIONS-I

    UNIT-IV
    SURFACEROUGHNESSMEASUREMENT:
    48
    Difference between surface roughness and surface
    waviness
    49 Numerical assessment of surface finish
    CLA Rt, R.M.S.Rz
    50
    R10 values
    51

    Method of Measurement of surface finish-profilograph


    52

    53 Talysurf ,ISI symbols for indication of surface finish

    54 Types of comparators

    55 Mechanical comparators
    57 Optical comparators
    58 Electrical comparators
    59 Electronic comparators
    60 Pneumatic comparators and their uses

    UNIT – V
    61 GEAR MEASUREMENT
    Tooth thickness measurement with gear tooth venire.
    62 Tooth thickness measurement with flange micrometre

    63 Pitch measurement

    64 Total composite error

    65 Tooth to tooth composite error

    66 Rolling gear tester

    67 Involutes profile checking

    68 Elements of measurement
    Errors in screw threads
    69

    70 Concept of virtual effective diameter


    71 Measurement of effective diameter
    72 Angle of thread and thread pitch
    73 Pitch thread gauges
    UNIT – VI
    74 FLATNESS MEASUREMENT
    Measurement of flatness of surfaces

    75 Instruments used for measurement of surfaces

    76 Straight edges
    Surface plates
    77

    78 Auto collimetre
    Principles of machine tools alignment on lathe machine
    79
    Principle of machine tools alignment on drilling
    80 machine
    81 Principle of machine tools alignment on milling
    machine
    82 Revision

    83 Revision.

    84 Revision

    85 Revision

    86 Revision

    87 Revision

    88 Revision

    89 Revision

    90 Revision
    Mid Exams-II
    TEXT BOOKS:
    1. Engineering Metrology by R.K.Jain / Khanna Publishers
    2. Engineering Metrology by Mahajan / Dhanpat Rai Publishers

    REFERENCES:
    1. Dimensional Metrology, Connie Dotson, Cengage Learning.
    2. Engineering Metrology by I.C.Gupta / Dhanpat Rai Publishers.
    3. Precision Engineering in Manufacturing by R.L.Murthy / New Age.
    4. Engineering Metrology and Measurements by NV Raghavendra, L Krishna murthy, Oxford publishers.
    Engineering Metrology by KL Narayana, Scitech publishers
    List the Course Outcomes (Cos):

    Sub code Sub Name COs Expected level of attainment


    On 5 scale

    3.5
    1. Inspection of engineering parts
    with various precision instruments.
    2. Design of part, tolerances and fits
    METROLOGY 3.5
    components in a gas power plant.
    3 Principles of measuring
    instruments and gauges and their
    uses.
    3.5
    4. Inspection of spur gear and thread
    elements.
    3.5

    Signature of faculty Head of the Department

    You might also like