Installation and Operation Manual Self-Priming Centrifugal Pumps
Installation and Operation Manual Self-Priming Centrifugal Pumps
Installation and Operation Manual Self-Priming Centrifugal Pumps
Series: POLA
POLB
POLC
2” thru 6”
B. INSTALLATION RECOMMENDATIONS
(Clearances, Pump Suction, Base Mounted Units) ..........................................4
(Pump Discharge) (Fig 1 & 2)...........................................................................5
(Influent Pipe, Level Controls)...........................................................................6
D. OPERATION RECOMMENDATIONS...............................................................7
E. PREVENTATIVE MAINTENANCE....................................................................8
F. LUBRICATION MAINTENANCE
(Single Mechanical Seal) (Fig. 4)......................................................................8
(Double Mechanical Seal) (Fig. 5)....................................................................8 - 9
(Bearing-Oil); Bullseye, Opto-Matic) (Fig. 6, 7 & 8)...........................................9
I. OPTIONAL EQUIPMENT
(Pump Case Heater) (Fig. 17)...........................................................................13
(Temperature Control) (Fig. 18).........................................................................13
J. TROUBLE SHOOTING.....................................................................................14 - 15
K. REPLACEMENT PARTS...................................................................................15
PO2LA CROSS-SECTION & PARTS LIST.......................................................16 - 18
PO3LA & PO3LB CROSS-SECTION & PARTS LIST.......................................19 - 21
PO3LC, PO4LA & PO4LB CROSS-SECTION & PARTS LIST.........................22 - 24
PO4LC CROSS-SECTION & PARTS LIST.......................................................25 - 27
PO6LB & PO6LC CROSS-SECTION & PARTS LIST.......................................28 - 30
Other brand and product names are trademarks or registered trademarks of their respective holders.
® CROWN is a registered trademark of Crane Pumps & Systems, Inc
® Teflon is a registered trademark of E.I. Dupont de Nemours and Company
® Crane-Carb is a registered trademark of John Crane International
1994, 2002, 3/04, 8/05, 2/06, 8/06, 9/06, 3/07 Alteration Rights Reserved
2
SAFETY FIRST!
Please Read This Before Installing Or Operating Pump. CAUTION! - Do not block or restrict discharge hose, as
This information is provided for SAFETY and to PREVENT discharge hose may whip under pressure.
EQUIPMENT PROBLEMS. To help recognize this information,
observe the following symbols:
WARNING! - DO NOT wear loose clothing that may become
IMPORTANT! Warns about hazards that can result entangled in the impeller or other moving parts. Always
in personal injury or Indicates factors concerned with wear appropriate safety gear, such as safety glasses,
assembly, installation, operation, or maintenance which when working on the pump or piping.
could result in damage to the machine or equipment if
ignored. WARNING! - Keep clear of suction and discharge
openings. DO NOT insert fingers in pump with power
CAUTION ! Warns about hazards that can or will cause minor connected.
personal injury or property damage if ignored. Used with symbols
below.
Always wear eye protection when working on pumps.
WARNING ! Warns about hazards that can or will cause serious
personal injury, death, or major property damage if ignored. Used
with symbols below. Make sure lifting handles are securely fastened each
Hazardous fluids can time before lifting. DO NOT operate pump without
cause fire or explo- Extremely hot - Severe safety devices in place. Always replace safety devices
sions, burnes or death burnes can occur on contact. that have been removed during service or repair.
could result. Secure the pump in its operating position so it can not
Hazardous fluids can Hazard- tip over, fall or slide.
Biohazard can cause ous pressure, eruptions
serious personal injury. or explosions could cause
DO NOT exceed manufacturers recommendation for
personal injury or property
maximum performance, as this could cause the motor
Rotating machinery to overheat.
Amputation or severe Hazardous voltage can
shock, burn or cause death.
laceration can result. WARNING! Cable should be protected at all times to
avoid punctures, cut, bruises and abrasions - inspect
Toxic Fumes - frequently. Never handle connected power cords with
Eye protectiong required
Breathing can cause wet hands.
nausea, fainting or death
Only qualified personnel should install, operate and repair WARNING! To reduce risk of electrical shock, all wiring
pump. Any wiring of pumps should be performed by a qualified and junction connections should be made per the NEC
electrician. or CEC and applicable state or province and local
codes. Requirements may vary depending on usage
WARNING ! - To reduce risk of electrical shock, pumps and location.
and control panels must be properly grounded in
accordance with the National Electric Code (NEC) or WARNING! Products Returned Must Be Cleaned,
the Canadian Electrical Code (CEC) and all applicable Sanitized, Or Decontaminated As Necessary Prior
state, province, local codes and ordinances. Improper To Shipment, To Insure That Employees Will Not Be
grounding voids warranty. Exposed To Health Hazards In Handling Said Material.
Prior to energizing the pump, a verification of the pump All Applicable Laws And Regulations Shall Apply.
ground circuit should be made between the pump case
and ground panel. Bronze/brass and bronze/brass fitted pumps may
WARNING! - To reduce risk of electrical shock, always contain lead levels higher than considered safe for
disconnect the pump from the power source before potable water systems. Lead is known to cause cancer
handling or servicing. Lock out power and tag. and birth defects or other reproductive harm. Various
government agencies have determined that leaded
WARNING! Operation against a closed copper alloys should not be used in potable water
discharge valve will cause premature bearing applications. For non-leaded copper alloy materials of
and seal failure on any pump, and on end construction, please contact factory.
suction and self priming pump the heat build
may cause the generation of steam with resulting dangerous
pressures. It is recommended that a high case temperature IMPORTANT! - Crane Pumps & Systems, Inc. is not responsible
switch or pressure relief valve be installed on the pump body. for losses, injury, or death resulting from a failure to
observe these safety precautions, misuse or abuse of
CAUTION! Pumps build up heat and pressure pumps or equipment.
during operation-allow time for pumps to cool
before handling or servicing.
3
SECTION A: GENERAL INFORMATION 3. When horizontal suction line (item 3) exceeds 10 feet, or
less than 1 foot or when total horizontal and vertical
A-1) To the Purchaser: length exceeds 30 feet, consult factory for operation limits.
Congratulations! You are the owner of one of the finest
pumps on the market today. CROWN® Pumps are products 4. An adjustable stand, pipe clamp (item 16) or floor flange
engineered and manufactured of high quality components. Over must be installed to support the weight of the suction line.
one hundred years of pump building experience along with a
continuing quality assurance program combine to produce a 5. Suction line must be air tight.
pump which will stand up to the toughest pumping projects.
6. Maximum performance is obtained when suction line and
This manual will provide helpful information concerning instal- pump size are matched (with a 3 inch pump use a 3 inch
lation, maintenance, and proper service guidelines. suction line).
A-4) Service Centers: 12. The vertical portion (item 5) of the suction line should
For the location of the nearest Service Center, check your be in one piece to eliminate joint leaks.
Crown pumps representative or Crane Pumps & Systems in
Piqua, Ohio, telephone (937) 778-8947 or Crane Pumps & 13. The easy-access elbow (item 2) can be turned 90° right
Systems Canada Inc., Brampton, Ontario (905) 457-6223. or left to facilitate installation and accessibility to the
pump case cover.
4
FIGURE 1
TYPICAL INSTALLATION
B-4) Pump Discharge: The (b) condition works well for slower speeds where
1. The air bleed line (item 12 & 13) should be 3/4 inch on considerable debris is encountered. However, the pipe
3 inch pumps, one inch on 4 and 6 inch pumps in order should not project more than one foot below the low
to reduce the priming time to a minimum. This is liquid level. If there are no leaks in the system, the pump
mandatory on force main installations. never loses prime.
4. There are two ways (item 12) & (item 13) of returning
this line to the pit: (a) The line discharging above the
liquid level (item 12). (b) The line discharging below the
low liquid level (item 13). The (a) condition is generally
accepted, but has the disadvantage of losing its prime
if the suction check valve is held open by debris.
This is generally no problem at higher speeds (1600 rpm
or higher).
5
5. The return of the air bleed line to the pit must be SECTION C: PARTS & FUNCTIONAL INFORMATION
separated from the suction pipe as far as possible in
order to eliminate churning air into the sump liquid. See Figure 3 For Typical Pump Cut-away, Actual cross
sections at back of manual.
6. The discharge check valve (item 7), required by standard
of design, should be installed in the horizontal position to (item 20) Easy access clean out & fill hole. The cover serves
avoid deposits between the disc and the body. This as a fill hole for initial priming of the pump, for easy examina-
check valve should have a spring loaded or externally tion or replacement of check valve, and as a quick clean out
weighted arm. hatch for unclogging the impeller.
7. Standards of design require a gate valve (item 8) down (item 21) Easily replaceable check valve.
stream from the check valve and is necessary when
cleaning or repairing the check valve. (item 22) The gaskets at the suction and discharge flanges
are of a high quality and not likely to leak, but the suction
8. Support the discharge line to prevent strain on the pump gasket should not be overlooked if trouble exists.
case.
(item 23) If this o-ring leaks (even only a few drops), a prim-
B-5) Influent Pipe: ing problem will exist. Make sure the chamfer which the o-ring
If the influent pipe (item 15) is located where falling water seats against is clean and smooth with no nicks in the o-ring.
churns air into the sump liquid causing air to enter the suction Always grease the o-ring and the area where it seats when
pipe, a baffle may be necessary to keep pumping and priming installing.
from being affected.
(item 24) The large hatch cover can be easily removed for
B-6) Sump Liquid Level Controls: inspection or replacement of internal parts on 2” through 6”
Because priming will be severely affected, air bubbling liquid pump models only.
level control pipes (item 14) must not be located near or
attached to the suction inlet pipe (item 5). (item 25) This o-ring is not as critical as (item 23). However,
it must never leak around the top half of the case or suc-
tion problems can exist. Always grease this o-ring and the
complete area this o-ring slides in before inserting case cover
(item 24).
FIGURE 3
6
(item 26) The clearance between the impeller and the volute (item 41) Horse shoe shims are used between the case and
is set at approximately .015 inches at the factory. As wear the pedestal permitting external adjustment of clearance
clearance increases, the pump head pressure is reduced between impeller and volute wear surface (item 26) without
and priming ability is severely affected. Readjust by removing dismantling the pump. Loosen 6 nuts, remove or add shims
shims (item 41). in equal amounts at each location, and retighten the 6 nuts
until the proper clearance is obtained. The thinnest shims are
(item 27) Both drain plugs must be removed to properly drain approximately .015 inches thick. O-ring (item 32) provides the
the pump. When draining for winter storage or for sever cold necessary sealing at all times.
weather, remove the complete hatch cover (item 24).
7
SECTION E: PREVENTATIVE MAINTENANCE
FIGURE 4
FIGURE 5
8
3. After adding oil it is a good idea to bleed off any air that is
in the seal cavity. To do this first make sure that the pump is
running. Second, use a flat head screwdriver to turn the air
bleed valve head (item 1) counterclockwise. This will open
the air bleed valve and at this point any air in the seal cavity
will be purged (bubbled) out through this valve. When nothing
but oil is coming out, then close the valve. This can only be
done when the pump is running (i.e. when there is pressure
in the oiler reservoir).
FIGURE 8
FIGURE 6
SECTION G: SHAFT SEAL REPLACEMENT:
Opto-Matic Oiler (See Figures 7 & 8)-On pumps where the G-1) Replacement Through Hatch Cover:
Opto-matic constant level oiler is used, the oiler will provide G-1.1) Disassembly:
an oil level to the center of the lower ball of the bearings, if All parts of the pump are easily dismantled by simply remov-
the pump is sitting level and the oiler is properly filled. Refill ing nuts and screws. Rotating parts of the shaft seal grip
with SAE 30 non-detergent oil. Replace vent plug (item 2) the shaft by friction and may be frozen to the shaft through
when finished refilling. long usage. If the mechanical shaft seal is not leaking and
it is necessary to dismantle part of the pump for inspec-
Fill bottle as shown in Figure 8, then invert and quickly screw tion or cleaning, DO NOT disturb the shaft seal other than
into lower reservoir. Several fillings of the bottle may be re- its spring if the impeller is removed. Once a shaft seal
quired before the oil level in the bearing reservoir is equal to has been in operation it cannot be reused without leaking.
the level for which the oiler is set. Never fill through the lower
reservoir because there is danger of over filling and oil being Remove hatch cover (24), by removing wing nuts and prying
thrown from the seals. If there is ever any question about the the cover off. Now remove capnuts (40) and pull the volute
oil level, drain the reservoir and start over. (29) and seal Plate (31) out of the pump case, (See Figure 3).
Remove the impeller nut, it is a standard right hand thread,
If for various reasons, conditions require a higher oil level, remove impeller washer, and then remove the impeller (28).
loosen the screws as shown in Figure 8, adjust to the desired The impeller has been provided with two drilled and tapped
level and tighten screws. holes for a wheel puller, if necessary use a wheel puller to
remove the impeller.
9
Remove the seal spring and spring holder. At this time the low the new seal to leak. At this time the shaft slinger used on
rotating portion and the seat can be removed without further single seal applications, should be examined and replaced if
dissassembling of the pump. However, it is generally easier to necessary.Inspect o-ring (32) carefully for cuts or nicks. Clean
remove the four (4) nuts that hold the pump side in place and the groove in the pump side and the mating bore in the pump
by using two pry bars, force the pump side with the old seal case carefully and grease at reassembly. See Section G-3 for
off the shaft. The grease cup (38) must first be removed.By Single seal installation or G-4 for Double seal installation.
using this method the lip seal (34) can be be replaced and
the seal seat can be easily removed and cleaned. Use care Reassemble pedestal assembly into pump and set the clear-
in cleaning the shaft because nicks can allow the new seal to ance by adding or removing shims (33) until the impeller rubs
leak.At this time the shaft slinger used on single seal applica- slightly, then add one thin shim (.015 thick) on PO2 to PO6
tions, should be examined and replaced if necessary.Inspect pump at each location and tighten the nuts securely.
o-ring (32) carefully for cuts or nicks. Clean the groove in the
pump side and the mating bore in the pump case carefully G-3) Single Seal Installation:
and grease at reassembly. See Section G-3 for Single seal Carefully identify all the parts in Figures 9 and 10, and famil-
installation or G-4 for Double seal installation. iarize yourself with their part names.
G-1.2) Reassembly: The mating ring (7) and seat (1) have been precision lapped
After the seals have been replaced and the impeller secured and must not be scratched or cracked during assembly. Also,
on the shaft (see Table 1), Place the seal plate (31) over the cleanliness is of utmost importance.
studs of the volute (29) and insert this assembly over the im-
peller with the volute studs projecting through the case.
Replace the cap or self locking nuts and tighten them (only
finger tight at this time). NOTE: On models PO6LB and PO6LC
it is necessary to insert the seal plate over the impeller then
insert the volute.
Replace o-ring (30) on the volute, and o-rings (23) and (25)
on the hatch cover, grease these o-rings and the areas they
contact thoroughly. Now insert the hatch cover (24) and
securely tighten the wing nuts. Normally these wing nuts can
be tightened sufficiently by hand. This method of securing the
hatch cover first, centers the volute properly over the impeller.
Tighten the cap nuts (40) that hold the volute in place.
The clearance between an open faced impeller and its wear sur-
face in the volute is set at the factory to approximately .015 inch-
es on PO2 to PO6 pumps. This clearance is readjustable on all FIGURE 9
pumps by adding or removing of horseshoe shims (33) located
at the bearing adapter flange, or on small units by relocating the
shaft at the clamping arrangement. Add or remove shims until STEP 1:
the impeller rubs slightly, then add one thin shim (.015 thick) on Make sure that the shaft and seat areas in the pump side are
2” to 6” pumps at each location and tighten the nuts securely. as clean as possible. Shoulder “A” on the shaft must not be
sharp, but neatly rounded and polished to a 1/32” radius. This
G-2) Replacement By Removing Pedestal: radius and the shaft, on which the rubber bellows grips, must
On belt drive units the belt tension must be relieved and the be polished with 180 to 240 grit emery cloth. The seal will
guard and the belts removed. On flexible coupled units the install relatively easy if the shaft is properly polished.
motor base bolts must be removed and the motor detached
from the coupling. Then remove the pedestal bolts attaching STEP 2:
the pedestal to the base. Install the seat assembly (1 and 2 or 1A and 2A, see Figure
10) (see section G-4), in the bottom of the pump side using
The only models that have impellers too large to be removed P-80 rubber lubricant emulsion (from International Products
through the case pump side opening are PO3LA-8D and Corp.) or SAE 10 non-detergent oil can be used, on the rub-
PO4LA-9D. ber parts. They may install easier by first inserting the rubber
part and then sliding the seat part into the rubber. All of this
After removing the pedestal assembly, the impeller, the old must be done with the fingers only.
seal, and pump side parts are removed. First remove the
impeller nut, it is a standard right hand thread, then remove STEP 3:
the impeller (28). The impeller has been provided with two We are now ready to install the rotating portion of the seal
drilled and tapped holes for a wheel puller, if necessary use a without the spring (see section G-4). Lubricate the shaft and
wheel puller to remove the impeller. Remove the the four (4) the inside of the bellows (8) each with 2 or 3 drops of P-80
nuts that hold the pump side in place and by using two pry rubber lubricant emulsion (from International Products Corp.)
bars, force the pump side with the old seal off the shaft. The or SAE 10 non-detergent oil can be used. Now with dry clean
grease cup (38) must first be removed. The lip seal (34) can hands, grasp this rotating portion in one or both hands (one
be be replaced and the seal seat can be easily removed and hand for small seals - two hands for large sizes) and use a
cleaned. Use care in cleaning the shaft because nicks can al- circular and rocking motion to push this portion onto the shaft,
10
1 - Ni-Resist Stationary Seat
1A - Ceramic Stationary Seat
2 - Buna-N Seat Ring
2A - Buna-N Seat Cup
3 - Stainless Retainer
4 - Stainless Drive Band
5 - Stainless Spring
6 - Stainless Springholder
7 - Crane-Carb® Mating Ring
7A - Carbon Mating Ring
8 - Buna-N Bellows
STEP 4:
Replace the impeller, torque impeller nut per Table 1, and
your seal installation is complete.
STEP 5: FIGURE 11
Seals of this type are generally lubricated by a spring loaded
automatic grease cup. For grease lubrication, use a good
quality non-fibrous #1 or #2 lithium base grease. The #1 is STEP 1:
best, except when high ambient temperatures are encoun- Make sure that the shaft and seat areas in the pump side and
tered. closure plate are as clean as possible. Shoulder “A” on the
shaft must not be sharp, but neatly rounded and polished to a
TABLE 1 - Impeller Nut Torque Values 1/32” radius. If this radius and the first 1/4” past the shoulder
PUMP MODEL NUT P/N TORQUE VALUE is highly polished with crocus cloth, the rotating portion of the
PO2LA M-7246 55 ft. lbs seal will install relatively easy. The rest of the shaft on which
the rotating portion of the seal will grip, should be cleaned
PO3LA M-7883 100 ft. lbs with 180-grit emery cloth.
PO3LB M-7883 100 ft. lbs
PO3LC M-7884 240 ft. lbs STEP 2:
Install the seat assembly (1 & 2), see Figure 12 and section
PO4LA M-7884 240 ft. lbs G-4, in the bottom of the pump side and closure plate using
PO4LB M-7884 240 ft. lbs P-80 rubber lubricant emulsion (from International Products
Corp.) or SAE 10 non-detergent oil can be used on the rubber
PO4LC M-7884 240 ft. lbs
parts. They may install easier by first inserting the rubber cup
PO6LB 525-00263 300 ft. lbs (2) and then sliding the ceramic seat (1) into the rubber cup.
PO6LC 525-00263 300 ft. lbs This all must be done with the fingers only.
11
FIGURE 12 1 - Ceramic Stationary Seat
2 - Buna-N Cup
3 - Carbon Mating Ring
4 - Buna-N Bellows
5 - Stainless Retainer
6 - Two Springs
7 - Stainless Disc
8 - Stainless Drive Band
9 - Buna-N O-ring
10 - Carbon Mating Ring
11 - Teflon Back-Up Ring
12 - Holding Clips (4)
STEP 5:
Double seals of this type are generally lubricated through the
use of a pressure balanced oil cylinder or a spring loaded au-
tomatic grease cup. In either case, the air must be bled from
this seal cavity while it is being filled with oil or grease. Where
oil is used, a thumb vent screw is furnished for venting and
where grease is used, a 1/8” pipe plug is furnished. Be sure
to vent all the air out of this cavity. It is best to use an SAE 30
non-detergent oil for the oil lubrication.
FIGURE 15
FIGURE 13
12
On some models
The normal installation more spring loading is
consists of 2 washers required and an extra
as shown flat washer is added as
shown
FIGURE 16
FIGURE 17
FIGURE 18a
FIGURE 18b
13
SECTION J: TROUBLE SHOOTING: Most of the problems encountered in self-priming pumps are
Locating a failure in a malfunctioning pump can be most due to air leaks on the suction side. Keeping this in mind, the
frustrating and even futile if not approached in a systematic following chart should help locate the trouble.
manner. To aid in locating the problem we recommend the
permanent installation of both of the following: If every check fails to identify where the leak is located, it may
be necessary to connect a pressure water supply to the drain
1. A vacuum gauge (10), See Figure 1, to provide information hole of the pump and hydrostatically test it. Keeping the water
from the suction side of the pump. A drilled and tapped hole pressure low, 5 to 10lbs. is ideal. Higher pressures may not
has been provided in the suction flange for such a gauge. show an o-ring leak. Also remove the cover from the grease
cup to permit water to escape should the seal be leaking.
2. A low-pressure, pressure gauge (11), See Figure 1, to sup-
ply information from the discharge side of the pump. A drilled If the above shows no leaks, remove some bolts from the
and tapped hole has been provided on the discharge flange suction flange, insert a solid steel backing plate and tighten
for such a gauge. the flange. If, with the pump running, the vacuum gauge
reads as much or more than during normal operation, then
Always use a small valve for attaching the gauges and keep the problem is most likely in the suction pipe or sump area.
them shut off when not in use. A vacuum gauge left to flutter Don’t overlook the possibility of air entering the suction line,
with pulsations will develop a crack in the internal tube caus- air that could be coming from the air bubbler control pipe.
ing it to leak unknowingly and give priming problems.By using
the vacuum and pressure gauges, one will be able to locate
most of the problems that will occur.
TROUBLE SHOOTING
CAUTION ! Always disconnect the pump from the electrical power source before handling.
If the system fails to operate properly, carefully read instructions and perform maintenance recommendations.
14
TROUBLE SHOOTING
CAUTION ! Always disconnect the pump from the electrical power source before handling.
If the system fails to operate properly, carefully read instructions and perform maintenance recommendations.
F. Pump loose prime during op- a. Suction line for leak between cut-out and cut-off
eration - vacuum gauge recedes b. End of suction line for vortexing to suction pipe
to zero 2. Pump taking air c. Water level bubbler control line too close to suction pipe
d. The influent liquid for chuming air into the sump and
entering the suction pipe
a. Foundation bolts for looseness
1. Loose foundation b. Grouting
c. For cracks
2. Air leaks a. Refer to A-1, a through g
a. Drawdown too great
b. Capacity too great
3. Cavitation c. Unit not operating in proper NPSH rang
G. Pump primed and pumping, d. If reducing capacity quiets pump, then (c) above is
but too noisy cause, close discharge valve partially
a. Balls for wear
4. Bearings
b. Oil reservoir for lubrication
a. Coupling for proper alignment
5. Misalignment
b. Check base, not properly bolted down
a. Impeller for partial obstruction
6. Vibration b. Operating in cavitation range
c. Misalignment of coupling
1. Low voltage a. Voltage at motor terminals when loaded
15
PUMP MODEL: PO2LA, 2C00D-0006C-001
1 2 3 4 5 6 7 8 9 10 11 12 13 14
55
15
16 56
54
17 18 19 20 21
53
22
52
9 10
51 23
50 FILL 24
49
48
47
46 25
26
27
45
44
28
43
32 31 30 29
42 41 40 39 38 37 36 35 34 33
16
PUMP MODEL: PO2LA, 2C00D-0006C-001
PARTS KIT
Seal Kit.............................P/N: 089076 () 4, 11, 14, 29, 31, 34, 40, 42, 45, 54
Overhaul Kit, P02LA........P/N: 089087 () 4, 11, 14, 17, 18, 19, 20, 21, 26, 29, 31, 33, 34, 40, 42, 45, 54
PARTS LIST
ITEM QTY. PART NO DESCRIPTION
1 1 T-26624 Plate, Valve, Check
2 1 FP-3685-A Flange, Suction 2” NPT
3 1 4757 Plug, Pipe, Hex 1/4” NPT, Brass
4 1 T-15907 Valve, Check Neoprene
5 1 1-7-1 Screw, Hex Hd. 1/4-20 x 1.00 LG, Stainless
1 20-13-1 Washer, Lock, Split 1/4”
1 15-5-1 Nut, Hex 1/4-20, Stainless
1 P-3688 Valve, Check Neoprene
7 1 FP-4309 Elbow, Valve, Check
8 1 FP-4310 Cover, Fill
9 8 15-23-6 Nut, Hex 3/8-16, Zinc Pltd.
10 8 M-2635 Stud 3/8-16 X 1.50 Lg, Steel
11 1 T-26640 Gasket, Cover, Fill Buna-N
12 1 625-02802 Elbow, 2” NPT
13 1 625-02810 Nipple, Pipe 2” NPT x 3.50” Lg
14 1 M-2655 Cup, Grease
15 3 M-5479 Stud 3/8-16 x 1.75” Lg, Stainless
3 20-6-7 Washer, Flat 3/8”, Brass
3 M-6046 Nut, Cap, Hex 3/8-16, Steel/nylock
16 6 M-2635 Stud 3/8-16 X 1.50” Lg., Steel
6 20-14-6 Washer, Lock, Split 3/8”, Zinc Pltd.
6 15-23-6 Nut, Hex 3/8-16, Zinc Pltd.
17 1 M-6370 Spinner, Shaft Neoprene
18 1 089257 Glass, Sight
19 1 089258 Plug, Vent
20 2 625-00719 Bearing, Ball
21 2 T-27115 Gasket, Plate, Closure Vellumoid
22 2 FP-4342 Plate, Closure
23 2 M-6611 Spring, Disc
24 1 M-3169 Key 1/4” Sq X 1.50” Lg, Steel
25 1 T-27117 Shaft, Impeller
26 2 M-4799 Seal, Shaft
27 8 1-5-6 Screw, Hex Hd 1/4-20 X .75” Lg, Zinc Pltd.
8 20-13-6 Washer, Lock, Split 1/4”, Zinc Pltd.
28 1 FP-4341 Bracket, Support, Bearing
29 1 M-5625 Seal, Lip
30 1 FP-4343 Side, Pump
31 1 M-4292-F Seal, Mechanical, 1.00”
32 4 M-2635 Stud 3/8-16 X 1.50” Lg, Steel
4 20-14-6 Washer, Lock, Split 3/8” Zinc Pltd.
4 15-23-6 Nut, Hex 3/8-16, Zinc Pltd.
33 6 T-27116 Shim, Plastic, .015”
6 T-27116-A Shim, Plastic, .030”
34 1 M-6522 O-ring, Buna-N
35 1 FP-4305 Case, Pump
36 1 T-27337 Plate, Seal
37 1 FP-4348-B Impeller
38 1 TS-27114 Washer, Impeller, Stainless
39 1 M-7246 Nut, Lock 1/2-20, Stainless/Nylock
40 1 M-6457 O-ring Buna-N
41 1 FP-4307-B Volute
42 1 M-6458 O-ring Buna-N
43 1 625-00860 Plug, Pipe, Sq 1/8” NPT, Black
44 1 625-01247 Plug, Pipe 3/4” NPT, Galvanized
17
PUMP MODEL: PO2LA, 2C00D-0006C-001
45 1 M-6456 O-ring Buna-N
46 2 M-6499 Nut, Handle
47 2 M-2614 Stud 1/2-13 x 2.00” Lg, Steel
48 2 625-01104 Washer 1/2” Zinc Pltd.
49 1 M-4504 Key 3/16” Sq X .69” Lg, Steel
50 1 510-00521 Handle, Cover
51 2 2-114-6 Screw, Round Hd 1/4-20 X .50” Lg, Zinc Pltd.
2 20-13-6 Washer, Lock, Split 1/4”, Zinc Pltd.
52 2 M-5286 Stud 5/16-18 X 1.50” Lg, Steel
2 20-21-6 Washer, Flat 5/16”, Zinc Pltd.
2 M-3501 Nut, Wing 5/16-18, Zinc Pltd.
53 1 FP-4306 Cover, Case
54 1 T-26639 Gasket, Elbow Vellumoid
55 1 625-02828 Coupling, Reducer .38" x .25" NPT, Steel
56 1 625-01147 Nipple, Pipe .25" NPT x 1.50" Lg, Galvanized
18
PUMP MODEL: PO3LA & PO3LB
PO3LA-7B, 3C01D-0007B-031
PO3LA-8D, 3C01D-0008D-031
PO3LB-7B, 3C03D-0007B-031
19
PUMP MODEL: PO3LA & PO3LB
PO3LA-7B, 3C01D-0007B-031
PO3LA-8D, 3C01D-0008D-031
PO3LB-7B, 3C03D-0007B-031
PARTS KIT
Seal Kit, P03LA/P03LB................P/N: 089077 (†) 4, 6, 10, 25, 31, 34, 39, 41, 51, 52, 54
Overhaul Kit, P03LA/P03LB........P/N: 089088 () 4, 6, 10, 17, 18, 19, 20, 25, 28, 31, 33, 34, 39, 41, 51, 52, 54
PARTS LIST
ITEM QTY. PART NO. DESCRIPTION
1 1 FP-4531 Elbow, Suction 3”
2 1 625-02841 Pin, Spring 1/4” Dia x 1.00” Lg
3 2 1-149-6 Screw, Hex Hd 7/16-14 x 1.25”, Z.P.
2 20-27-6 Washer, Flat 7/16”, Zinc Pltd
4 1 MT-9037 † Gasket, Valve Neoprene
5 1 P-4530 Cover, Hatch
6 1 P-3748 † Weight, Valve
1 002161 † Bolt, Carraige 1/4-20 x 1.25”, Steel
1 20-13-1 † Washer, Lock, Split 1/4”, Stainless
1 15-5-1 † Nut, Hex 1/4-20, Stainless
8 4 M-2614 Stud 1/2-13 x 2.00” Lg, Steel
4 20-15-6 Washer, Lock, Split 1/2”, Zinc Pltd
4 15-6-6 Nut, Hex 1/2-13, Zinc Pltd
9 1 625-02121 Flange, Companion 3”
10 1 M-2655 † Cup, Grease
11 1 625-02828 Coupling, Reducer 3/8” x 1/4” NPT, Stl
12 1 625-01147 Nipple, Pipe 1/4” NPT x 1.50”Lg Galv.
13 1 A-6694 Fitting, Discharge 3”
14 3 625-01247 Plug, Pipe 3/4” NPT, Galv.
15 3 M-5479 Stud 3/8-16 x 1.75” Lg, Steel
3 20-6-7 Washer, Flat 3/8”, Brass
3 M-6046 Nut, Cap, Hex 3/8”-16, Steel/Nylock
16 6 M-2771 Stud 1/2-13 x 1.75” Lg, Steel
6 20-15-6 Washer, Lock, Split 1/2”, Zinc Pltd
6 15-6-6 Nut, Hex 1/2-13, Zinc Pltd
17 1 M-4313 Spinner, Shaft Neoprene
18 1 089257 Glass, Sight
19 1 089258 Plug, Vent
20 2 T-24886 Gasket, Plate, Closure Vellumoid
21 2 FP-4261 Plate, Closure
22 2 M-4489 Spring, Disc
23 1 M-2222 Key 5/16” Sq x 2.00” Lg, Steel
24 1 T-24888-C Shaft, Impeller
25 3 M-4080 † Seal, Lip
26 8 1-5-6 Screw, Hex Hd 1/4-20 x .75” Lg, Z.P.
8 20-13-6 Washer, Lock, Split 1/4”, Zinc Pltd
27 1 FP-4263 Bracket, Support
28 2 M-6142 Bearing, Ball
29 1 512-00007 Sleeve, Shaft, Stainless
30 1 FP-4262-B Side, Pump
31 1 M-3983-F † Seal, Mechanical, 1.375”
32 4 M-2635 Stud 3/8-16 x 1.50” Lg, Steel
4 20-14-6 Washer, Lock, Split 3/8, Zinc Pltd
4 15-23-6 Nut, Hex 3/8-16, Zinc Pltd
33 6 T-27239 Shim, Plastic, .025”
6 T-27239-A Shim, Plastic, .015”
34 1 M-7965 † O-Ring, Buna-N
20
PUMP MODEL: PO3LA & PO3LB
PO3LA-7B, 3C01D-0007B-031
PO3LA-8D, 3C01D-0008D-031
PO3LB-7B, 3C03D-0007B-031
35 1 T-25459 Seal Plate PO3LA-7B
1 T-24989 PO3LA-8D
1 T-25459 PO3LB-7B
36 1 FP-4185-F Volute PO3LA-7B
1 FP-4184-F PO3LA-8D
1 FP-4296 PO3LB-7B
37 1 FP-4264-A Impeller PO3LA-7B
1 FP-4188-C PO3LA-8D
1 FP-4297-C PO3LB-7B
38 1 FP-4186-H Case, Pump
39 2 M-5691 † O-Ring Buna-N
40 1 625-00860 Plug, Pipe, Sq 1/8” NPT, Black
41 1 M-5690 † O-Ring Buna-N
42 1 M-2650 Key 1/4” Sq x 1.00” Lg, Steel
43 2 M-5800 Handle, Nut
44 2 TS-29413 Stud 5/8-11 x 2.50” Lg, Stainless
45 2 625-01103 Washer, Flat 5/8”, Zinc Pltd
46 1 M-7883 Nut, Lock, Hex 5/8-18, SST/Nylock
47 1 TS-24887 Washer, Impeller
48 1 510-00521 Handle, Cover
49 2 2-114-6 Screw, Round Hd 1/4-20 x .50”Lg, ZP
2 20-13-6 Washer, Lock, Split 1/4”, Zinc Pltd
50 1 FP-4187-A Cover, Case
51 1 M-9589 † Gasket, Elbow
52 1 089113 † Gasket, Valve, Check Neoprene
53 1 4757 Plug, Pipe, Hex 1/4” NPT, Brass
54 1 P-3748 † Weight, Valve, Check
21
PUMP MODELS: PO3LC, PO4LA & PO4LB
PO3LC-8L, 3C06D-0008L-031; PO4LA-8D, 4C02D-0008D-031;
PO4LA-9D, 4C02D-0009D-031; PO4LB-8D, 4C04D-0008D-031
22
PUMP MODELS: PO3LC, PO4LA & PO4LB
PO3LC-8L, 3C06D-0008L-031; PO4LA-8D, 4C02D-0008D-031;
PO4LA-9D, 4C02D-0009D-031; PO4LB-8D, 4C04D-0008D-031
PARTS KITS
Seal Kit, P03LC/4LA/4LB................P/N: 089078 () 7, 14, 26, 33, 35, 39, 40, 51, 53, 54, 55, 56
Overhaul Kit, P03LC/4LA/4LB........P/N: 089089 () 7, 13, 14, 19, 20, 21, 26, 28, 29, 33, 35, 39, 40, 51, 53, 54,
55, 56
PARTS LIST
ITEM QTY. PART NO DESCRIPTION
1 1 625-02838 Flange, Companion 3” (PO3LC ONLY)
2 1 T-9502 Gasket, Flange 4” (PO3LC ONLY)
3 1 FP-4514 Elbow, Suction 4”
4 1 625-02841 Pin, Spring 1/4” Dia x 1.00” Lg
5 2 1-71-6 Screw, Hex Hd 1/2-13 x 1.75” Lg, Z.P
2 625-01104 Washer, Flat 1/2”, Zinc Pltd
6 1 P-4515 Cover, Hatch
7 1 P-3757 Weight, Valve
8 14 M-2614 Stud 1/2-13 x 2.00” Lg, Steel
14 20-15-6 Washer, Lock, Split 1/2”, Zinc Pltd
14 15-6-6 Nut, Hex 1/2-13, Zinc Pltd
9 2 4757 Plug, Pipe, Hex 1/4” NPT, Brass
10 1 FP-4496 Connection, Flanged 3” (PO3LC)
1 FP-4376 Connection, Flanged 4” (PO4LA, LB)
11 1 625-01652 Plug, Pipe, Sq 1” NPT, Cast Iron
12 3 M-5479 Stud 3/8-16 x 1.75” Lg, Stainless
3 20-6-7 Washer, Flat 3/8”, Brass
3 M-6046 Nut, Cap, Hex 3/8-16, Steel/Nylock
13 6 T-27240 Shim, Plastic, .035”
6 T-27240-A Shim, Plastic, .015”
14 1 M-2655 Cup, Grease
15 1 625-02828 Coupling, Reducer 3/8” x 1/4” NPT, Stl
16 1 625-01148 Nipple, Pipe, Close 1/4” NPT
17 1 FP-4272 Bracket, Support
18 1 21093 Washer 1.69X3X1/8 Buna-N
19 1 089257 Glass, Sight
20 1 089258 Plug, Vent
21 2 T-25358 Gasket, Plate, Closure Vellumoid
22 2 FP-2763-D Plate, Closure
23 2 M-6570 Spring, Disc Steel
24 1 M-4341 Key 3/8” Sq x 2.50” Lg, Steel
25 1 T-25043-C Shaft, Impeller
26 3 M-2783 Seal, Lip
27 8 1-34-6 Screw, Hex Hd 3/8-16 x 1.00” Lg, Z.P
8 20-14-6 Washer, Lock, Split 3/8”, Zinc Pltd
28 1 M-5436 Bearing, Ball
29 1 M-2654 Bearing, Ball
30 1 512-00004 Sleeve, Shaft Stainless
31 1 FP-4273-A Side, Pump
32 4 M-2635 Stud 3/8-16 x 1.50” Lg, Steel
4 20-14-6 Washer, Lock, Split 3/8”, Zinc Pltd
4 15-23-6 Nut, Hex 3/8-16, Zinc Pltd
33 1 M-6568 O-Ring Buna-N
34 1 T-32643 Plate, Seal PO3LC-8L
1 T-24993 Plate, Seal PO4LA-8D
1 T-24992 Plate, Seal PO4LA-9D
1 T-24993 Plate, Seal PO4LB-8D
35 1 M-3842-F Seal, Mechanical, 1.75”
23
PUMP MODELS: PO3LC, PO4LA & PO4LB
PO3LC-8L, 3C06D-0008L-031; PO4LA-8D, 4C02D-0008D-031;
PO4LA-9D, 4C02D-0009D-031; PO4LB-8D, 4C04D-0008D-031
36 1 FP-4570-A Case, Pump
37 1 FP-4494 Impeller PO3LC-8L
1 FP-4271-A Impeller PO4LA-8D
1 FP-4271 Impeller PO4LA-9D
1 FP-4285-A Impeller PO4LB-8D
38 1 FP-4493-A Volute PO3LC-8L
1 FP-4198-K Volute PO4LA-8D
1 FP-4198-L Volute PO4LA-9D
1 FP-4284-D Volute PO4LB-8D
39 2 M-5728 O-Ring Buna-N
40 1 M-5727 O-Ring Buna-N
41 1 FP-4571-A Cover, Case
42 1 625-00860 Plug, Pipe, Sq 1/8” NPT, Black
43 2 625-01247 Plug, Pipe 3/4” NPT, Galvanized
44 4 2-114-6 Screw, Round Hd 1/4-20 x .50”Lg, Z.P
4 20-13-6 Washer, Lock, Split 1/4”, Zinc Pltd
45 2 510-00521 Handle, Cover
46 1 M-7884 Nut, Lock, Hex 1-14, Stainless/Nylock
47 1 525-00357 Key 3/8” Sq x 1.375” Lg, Steel
48 1 TS-13919 Washer, Impeller Stainless
49 4 FP-4574 Nut, Wing 5/8-11, Cast Iron
50 4 TS-29413 Stud 5/8-11 x 2.50” Lg, Stainless
51 2 M-9590 Gasket, Elbow
52 8 1-97-6 Screw, Hex Hd 5/8-11 x 2.75”Lg, Z.P
8 15-21-6 Nut, Hex 5/8-11, Zinc Pltd
53 1 MT-8840 Rubber, Valve Neoprene
54 1 P-3115 Weight, Valve
55 1 25-111-6 Bolt, Carriage 1/2-13 x 1.25”Lg, Z.P
1 15-6-1 Nut, Hex 1/2-13, Stainless
56 1 525-00004 Gasket, Valve, Check Neoprene
24
PUMP MODEL: PO4LC
PO4LC-9D, 4C07D-0009D-031; PO4LC-9L, 4C07D-0009L-031;
PO4LC-10D, 4C07D-0010D-031; PO4LC-10L, 4C07D-0010L-031
25
PUMP MODEL: PO4LC
PO4LC-9D, 4C07D-0009D-031; PO4LC-9L, 4C07D-0009L-031;
PO4LC-10D, 4C07D-0010D-031; PO4LC-10L, 4C07D-0010L-031
PARTS KITS
Seal Kit, P04LC................P/N: 089079 () 4, 5, 8, 13, 15, 26, 38, 43, 44, 58, 59, 60
Overhaul Kit, P04LC........P/N: 089090 () 4, 5, 8, 13, 15, 17, 19, 21, 26, 29, 30, 37, 38, 43, 44, 58, 59, 60
PARTS LIST
ITEM QTY. PART NO DESCRIPTION
1 1 625-02841 Pin, Spring 1/4” Dia x 1.00” Lg
2 2 1-71-6 Screw, Hex Hd 1/2-13 x 1.75” Lg, Z.P.
2 625-01104 Washer 1/2”, Zinc Pltd
3 1 P-4515 Cover, Hatch
4 1 P-3757 Weight, Valve, Flap
5 1 25-111-6 Bolt, Carraige 1/2-13 x 1.25” Lg, Z.P.
1 15-6-1 Nut, Hex 1/2-13, Stainless
6 2 4757 Plug, Pipe, Hex 1/4” NPT, Brass
7 1 FP-4376 Connection, Flange 4”
8 1 M-2655 Cup, Grease
9 1 625-02828 Coupling, Reducer 3/8” x 1/4” NPT, Steel
10 1 625-01148 Nipple, Pipe, Close 1/4” NPT, Galv.
11 1 625-01652 Plug, Pipe, Sq 1” NPT
12 8 M-2614 Stud 1/2-13 x 2.00” Lg, Steel
8 20-15-6 Washer, Lock, Split 1/2”, Zinc Pltd
8 15-6-6 Nut, Hex 1/2-13, Zinc Pltd
13 2 M-9590 Gasket, Elbow
14 3 M-5542 Stud 1/2-13 x 2.00”, Stainless
3 M-3543 Washer 1/2”, Brass
3 16-6-6 Nut, Acorn 1/2-13, Zinc Pltd/Nylock
15 1 M-3842-F Seal, Mechanical, 1.75”
16 1 M-5087 Bolt, Eye 5/8-11, Steel
17 1 089257 Glass, Sight
18 1 15-22-6 Nut, Hex, Jam 5/8-11, Zinc Pltd
19 1 089258 Plug, Vent
20 1 FP-4358 Bracket, Support, Pump
21 2 T-25358 Gasket, Plate, Closure Vellumoid
22 2 FP-2763-D Plate, Closure
23 2 M-6570 Spring, Disc Steel
24 1 M-4341 Key 3/8” Sq x 2.50” Lg, Steel
25 1 T-27382-D Shaft, Impeller
26 3 M-2783 Seal, Lip
27 8 1-34-6 Screw, Hex Hd 3/8-16 x 1.00” Lg Z.P.
8 20-14-6 Washer, Lock, Split 3/8”, Zinc Pltd
28 1 FP-4359 Foot, Support
2 1-96-6 Screw, Hex Hd 5/8-11 x 2.50” Lg, Z.P.
2 20-24-6 Washer, Lock, Split 5/8”, Zinc Pltd
2 15-21-6 Nut, Hex 5/8-11, Zinc Pltd
29 1 M-5436 Bearing, Ball
30 1 M-2654 Bearing, Ball
31 1 512-00004 Sleeve, Shaft Stainless
32 1 M-4249 Spinner, Shaft Neoprene
33 1 FP-4356 Side, Pump
34 6 M-2659 Stud 1/2-13 x 2.50” Lg, Steel
6 20-15-6 Washer, Lock, Split 1/2”, Zinc Pltd
6 15-6-6 Nut, Hex 1/2-13, Zinc Pltd
35 6 M-2614 Stud 1/2-13 x 2.00” Lg, Steel
6 20-15-6 Washer, Lock, Split 1/2”, Zinc Pltd
6 15-6-6 Nut, Hex 1/2-13, Zinc Pltd
36 1 FP-4357 Ring, Mounting
26
PUMP MODEL: PO4LC
PO4LC-9D, 4C07D-0009D-031; PO4LC-9L, 4C07D-0009L-031;
PO4LC-10D, 4C07D-0010D-031; PO4LC-10L, 4C07D-0010L-031
37 6 T-27383 Shim, Plastic, .030”
6 T-27383-A Shim, Plastic, .015”
38 1 M-6613 O-Ring Buna-N
39 1 FP-4352-A Case, Pump
40 1 T-27584 Plate, Seal PO4LC-9D
1 T-27583 Plate, Seal PO4LC-9L
1 T-27582 Plate, Seal PO4LC-10D
1 T-27384 Plate, Seal PO4LC-10L
41 1 FP-4443-G Volute PO4LC-9D
1 FP-4443-E Volute PO4LC-9L
1 FP-4443-C Volute PO4LC-10D
1 FP-4443-A Volute PO4LC-10L
42 1 FP-4364-A Impeller PO4LC-9D
1 FP-4444-E Impeller PO4LC-9L
1 FP-4444-C Impeller PO4LC-10D
1 FP-4444-A Impeller PO4LC-10L
43 2 M-6614 O-Ring Buna-N
44 2 M-5727 O-Ring Buna-N
45 1 625-00860 Plug, Pipe, Sq 1/8” NPT, Black
46 2 625-01247 Plug, Pipe 3/4” NPT, Galvanized
47 2 M-6499 Nut, Handle 1/2-13
48 2 M-2614 Stud 1/2-13 x 2.00” Lg, Steel
49 2 625-01104 Washer 1/2”, Zinc Pltd
50 1 FP-4354 Hatch, Quick Opening
51 1 M-7884 Nut, Lock, Hex 1-14, Stainless/Nylock
52 1 M-1891 Key 3/8” Sq x 1.50” Lg, Steel
53 1 TS-13919 Washer, Impeller Stainless
54 4 2-114-6 Screw, Round Hd 1/4-20 x .50”Lg,Z.P.
4 20-13-6 Washer, Lock, Split 1/4”, Zinc Pltd
55 2 510-00521 Handle, Cover
56 1 FP-4353 Cover, Case
57 8 M-2333 Stud 5/8-11 x 2.25” Lg, Steel
8 20-24-6 Washer, Lock, Split 5/8”, Zinc Pltd
8 15-21-6 Nut, Hex 5/8-11, Zinc Pltd
58 1 MT-8840 Rubber, Valve Neoprene
59 1 P-3115 Weight, Valve
60 1 525-00004 Gasket, Valve, Check Neoprene
61 1 FP-4514 Elbow, Suction 4”
27
PUMP MODELS: PO6LB & PO6LC
PO6LB-10N, 6C05D-0010N-031; PO6LB-11J, 6C05D-0011J-031;
PO6LB-12F, 6C05D-0012F-031; PO6LC-13B, 6C08D-0013B-031;
PO6LC-14X, 6C08D-0014X-031
28
PUMP MODELS: PO6LB & PO6LC
PO6LB-10N, 6C05D-0010N-031; PO6LB-11J, 6C05D-0011J-031; PO6LB-12F, 6C05D-0012F-031;
PO6LC-13B, 6C08D-0013B-031; PO6LC-14X, 6C08D-0014X-031
PARTS KITS
Seal Kit, P06LB/LC............................. P/N: 089080 () 2, 9, 14, 15, 35, 53, 58, 59, 61, 67, 74
Overhaul Kit, PO6LB...........................P/N: 089091 () 2, 9, 14, 15, 16, 19, 20, 21, 22, 25, 32, 34, 35, 52,
53, 58, 59, 61, 67, 74
Overhaul Kit, PO6LC...........................P/N: 089092 (▲) 2, 9, 14, 15, 19, 20, 34, 35, 36, 38, 43, 52, 53, 58,
59, 61, 67, 74
PARTS LIST
ITEM QTY. PART NO DESCRIPTION
1 2 4757 Plug,Pipe, Hex 1/4” NPT, Brass
2 1 MT-9220 ▲ Gasket, Cover, Hatch Neoprene
3 4 1-71-6 Screw, Hex Hd 1/2-13 x 1.75” Lg, Z.P.
4 20-7-6 Washer, Flat 1/2”, Zinc Pltd.
4 1 P-4533 Cover, Hatch
5 1 FP-4532-A Elbow, Suction
6 8 M-9711 Stud 3/4-10 x 2.75” Lg, Steel
8 20-16-6 Washer, Lock, Split 3/4”, Zinc Pltd.
8 15-7-6 Nut, Hex 3/4-10, Zinc Pltd.
7 1 FP-4374-A Connection, Flanged 6”
8 1 003205 Plug, Pipe, Sq 1” NPT, Black
9 2 M-9591 ▲ Gasket, Flange Nitrile
10 5 TS-29413 Stud 5/8-11 x 2.50” Lg, Stainless
5 20-23-7 Washer, Flat 5/8”, Brass
5 625-02847 Nut, Lock 5/8-11, Stainless/Nylock
12 1 625-01148 Nipple, Pipe, Close 1/4” NPT, Galv.
13 1 625-02828 Coupling, Reducer 3/8” x 1/4” NPT
14 1 M-2655 ▲ Cup, Grease 3/8” NPT
15 1 M-4414-F ▲ Seal, Mechanical, 2.00”
16 1 M-9241 Gasket, Plate, Closure Vellumoid
17 1 M-5087 Bolt, Eye 5/8-11, Steel
18 1 15-22-6 Nut, Hex, Jam 5/8-11, Zinc Pltd.
19 1 089257 ▲ Glass, Sight
20 1 089258 ▲ Plug, Vent
21 1 M-2575 Bearing, Ball
22 1 T-25358 Gasket, Plate, Closure Vellumoid
23 1 FP-2763-D Plate, Closure
24 8 1-529-6 Screw, Hex Hd 3/8-16 x 1.00” Lg, Z.P.
8 20-14-6 Washer, Lock, Split 3/8”, Zinc Pltd.
25 1 M-2783 Seal, Lip
26 1 M-4341 Key 3/8” Sq x 2.50” Lg, Steel
27 1 510-00483-004 Shaft, Impeller
28 2 M-6570 Spring, Disc
29 2 1-93-6 Screw, Hex Hd 5/8-11 x 1.75” Lg, Z.P.
2 20-24-6 Washer, Lock, Split 5/8”, Zinc Pltd.
2 15-21-6 Nut, Hex 5/8-11, Zinc Pltd.
30 1 T-35658 Support, Foot
31 1 FP-4547 Bracket, Support, Pump
32 1 M-4342 Bearing, Ball
33 1 FP-3071-E Plate, Closure
34 1 068747 ▲ Ring, Slinger Buna-N
35 1 M-4413 ▲ Seal, Lip
36 2 T-25357 ▲ Gasket, Plate, Closure Vellumoid
37 2 FP-4159-B Plate, Closure
38 2 M-6252 ▲ Seal, Lip
39 1 M-2664 Key 1/2” Sq x 3.50” Lg, Steel
40 1 510-00480-003 Shaft, Impeller
41 2 M-5766 Spring, Disc
42 1 FP-4372 Foot, Support, Pump
2 1-96-6 Screw Hex Hd, 5/8-11 x 2.50” Lg, Z.P
2 20-24-6 Washer, Lock, Split 5/8”, Zinc Pltd.
2 15-21-6 Nut, Hex 5/8-11, Zinc Pltd.
43 2 M-5767 ▲ Bearing, Ball
44 1 FP-4371 Bracket, Support, Pump
45 6 T-28840 Stud 1/2-13 X 2.38” Lg, Steel
29
PUMP MODELS: PO6LB & PO6LC
PO6LB-10N, 6C05D-0010N-031; PO6LB-11J, 6C05D-0011J-031; PO6LB-12F, 6C05D-0012F-031;
PO6LC-13B, 6C08D-0013B-031; PO6LC-14X, 6C08D-0014X-031
6 21-13-6 Washer, Lock, Internal Tooth 1/2”,Z.P.
6 15-6-6 Nut, Hex 1/2-13, Zinc Pltd.
46 6 M-1784 Stud 5/8-11 x 2.50” Lg, Steel
6 20-24-6 Washer, Lock, Split 5/8”, Zinc Pltd.
6 15-21-6 Nut, Hex 5/8-11, Zinc Pltd.
47 1 FP-4373 Ring, Mounting
48 6 M-1784 Stud 5/8-11 x 2.50” Lg, Steel
6 20-24-6 Washer, Lock, Split 5/8” Zinc Pltd.
6 15-21-6 Nut, Hex 5/8-11, Zinc Pltd.
49 1 512-00005 Sleeve, Shaft, Stainless
50 1 M-4413 Seal, Lip
51 1 FP-4370 Side, Pump
52 6-12 T-27750 ▲ Shim, Plastic, .030”
9 T-27750-A ▲ Shim, Plastic, .015”
53 1 M-6680 ▲ O-Ring Buna-N
54 1 T-27741-A Plate, Seal PO6LB-10N, P06LC-10N
1 T-27743-A Plate, Seal PO6LB-11J,
1 T-27744-A Plate, Seal PO6LB-12X
1 T-28060-A Plate, Seal PO6LB-12F
1 T-28058-A Plate, Seal PO6LC-13B
1 T-27716-A Plate, Seal PO6LC-14X
55 1 FP-4377-A Volute P06LC-10N
1 FP-4368-H Volute PO6LB-11J
1 FP-4368-B Volute PO6LB-12F
1 FP-4368-E Volute PO6LC-13B
1 FP-4368-G Volute PO6LC-14X
1 FP-4368-C Volute P06LB-12X
56 1 FP-4250 Impeller P06LB-12X
1 FP-4250-A Impeller PO6LB-11J
1 FP-4250-B Impeller P06LC-10N
1 FP-4369-D Impeller PO6LB-12F
1 FP-4369-B Impeller PO6LC-13B
1 FP-4369 Impeller PO6LC-14X
57 1 M-4341 Key 3/8” Sq x 2.50” Lg (PO6LB ONLY)
1 525-00358 Key 3/8” Sq x 2.13” Lg (PO6LC ONLY)
58 1 M-5633-D ▲ Rubber Strip 1/2” Sq x 72” Lg.
59 1 M-5633-E ▲ Rubber Strip 1/2” Sq x 36” Lg.
60 1 FP-4367-C Case, Pump
61 1 T-24844 ▲ Gasket, Cover, Case Neoprene
62 1 FP-4252 Cover, Case
63 1 625-00971 Plug, Pipe, Sq 1/4” NPT, Galvanized
64 1 625-01175 Plug, Pipe, Sq 1-1/2” NPT,Black
65 4 1-529-6 Screw, Hex Hd 3/8-16 x 1.00” Lg, Z.P., 1-529-6
4 20-14-6 Washer, Lock, Split 3/8”, Zinc Pltd.
66 2 510-00587 Handle, Cover, Case
67 1 T-24845 ▲ Gasket, Hatch Neoprene
68 1 FP-4253 Hatch, Quick Opening
69 2 FP-4574 Nut, Wing 5/8-11
70 2 M-1784 Stud 5/8-11 x 2.50” Lg, Steel
2 625-01103 Washer, Flat 5/8”, Zinc Pltd.
71 1 525-00263 Nut, Lock 1-1/4-12, Stainless/Nylock
72 1 512-00018 Washer, Impeller Stainless
73 8 M-1784 Stud 5/8-11 x 2.50” Lg, Steel
8 M-2333 Stud 5/8-11, 2.25” Steel (P06LC ONLY)
8 20-24-6 Washer, Lock, Split 5/8”, Zinc Pltd.
8 15-21-6 Nut, Hex 5/8-11, Zinc Pltd.
8 070320 Flat Washer 5/8” Stainless
74 1 M-9403-A ▲ Gasket, Valve, Check Rubber
75 1 067502D Weight, Valve, Check
76 1 1-71-1 Screw, Hex Hd 1/2-13 x 1.75” Lg, SST
1 20-15-1 Washer, Lock, Split 1/2”, Stainless
1 15-6-1 Nut, Hex 1/2-13, Stainless
77 1 FP-4534-B Valve, Check
NS 1 003204 Plug, Pipe 3/4” NPT, Galvanized
30
IMPORTANT!
IMPORTANT!
WARRANTY REGISTRATION
WARRANTY REGISTRATION
Your product is covered by the enclosed Warranty.
If you have a claim under the provisions of the warranty, contact your local
Crane Pumps & Systems, Inc. Distributor.
RETURNED GOODS
RETURN OF MERCHANDISE REQUIRES A “RETURNED GOODS AUTHORIZATION”.
CONTACT YOUR LOCAL CRANE PUMPS & SYSTEMS, INC. DISTRIBUTOR.
31