IWCF Problems Feb-19
IWCF Problems Feb-19
IWCF Problems Feb-19
Contents
1. Static and Dynamic Pressures........................................................ 2
Bottom-hole pressure Change ................................................... 2
Dynamic Pressure...................................................................... 6
2. Leak-Off Test ................................................................................ 7
3. Tripping ...................................................................................... 10
4. Slug.............................................................................................. 14
5. Volumetric Method/Stripping...................................................... 15
6. Various ........................................................................................ 17
7. Model Answers ............................................................................ 20
1
1. Static and Dynamic Pressures
1.1 When drilling a 26 inch surface hole at 1200 feet True Vertical Depth (TVD),
the formation pressure is measured as exactly 601 psi.
How would you describe this formation pressure?
a. Above normal
b. Below normal
c. Normal
1.2 If the gas/water contact in a normally pressured reservoir is at 3950 feet, what
is the pressure at the top of the reservoir at 3470 feet? (There is a gas gradient
0.1 psi/ft, formation water gradient of 0.464 psi/ft.
a. 1350 psi
b. 1630 psi
c. 1785 psi
d. 1870 psi
2
1.3 There is a total power loss.
Partial losses are measured at 10 bbl/hour
Capacity of Annulus and Pipe contents – 0.073 bbl/ft
Drilling fluid density – 10.8 ppg
What will be the reduction in Bottom Hole Pressure (BHP) after 3 hours if the
hole cannot be filled?
a. 231 psi
b. 300 psi
c. 420 psi
d. 77 psi
1.5 A well is drilled to 9000 ft Measured Depth (MD) and the True Vertical Depth
(TVD), with 10 ppg of drilling fluid.
If the drilling fluid is then displaced to 11 ppg fluid, how would this affect the
hydrostatic pressure at the bottom of the hole?
a. Hydrostatic pressure would decrease
b. Hydrostatic pressure would increase
c. Hydrostatic pressure would stay the same
2
1.6 Pressure recorders located below the drill stem test tools show that the swab
pressure is 250.
Drilling fluid density in the hole is 10 ppg. .
Top of reservoir is at 9500 feet.
If the well does not flow when the pipe is static, what would the reservoir
pressure have to be at this swab pressure?
a. 3800 psi.
b. 5800 psi.
c. 4690 psi.
d. 4940 psi.
…………………… psi
1.8 Formation pressure at 9200 feet True Vertical Depth (TVD) is balanced by
10.6 ppg mud. A 250 psi trip margin must be included in the drilling fluid density.
What drilling fluid density would be required?
a. 10.1 ppg
b. 10.6 ppg
c. 11.2 ppg
d. 11.7 ppg
1.9 Formation pressure at 8350 feet True Vertical Depth (TVD) is anticipated to be
4430 psi.
A 250-psi trip margin must be included in the drilling fluid density.
What drilling fluid density would be required?
a. 10.2 ppg
b. 12 ppg
c. 9.6 ppg
d. 10.8 ppg
3
1.10 When drilling at 17750 feet Measure Depth (MD), 14650 feet True Vertical
Depth (TVD), formation pressure is balanced by 12.3 ppg drilling fluid.
A 350-psi trip margin must be included in the drilling fluid density.
What drilling fluid density is required?
…………………… ppg
1.11 Before pulling out of hole, the drilling fluid density is increased by 0.5 ppg
trip margin.
With this trip margin, calculate the increase in Bottom Hole Pressure (BHP).
Well Data:
Well depth (TVD): 8300 ft
Well depth (MD): 8900 ft
Drilling fluid density without trip margin: 11.2 ppg
Drill pipe capacity: 0.01782 bbl/ft
Drill pipe metal displacement: 0.00751 bbl/ft
……………………………………..psi
1.12 Formation pressure at 9200 feet True Vertical Depth (TVD) is balanced by
10.6 ppg mud weight and 287 psi trip margin must be included in the drilling
fluid density. What drilling fluid density is required?
a. 10.1 ppg
b. 10.6 ppg
c. 11.2 ppg
d. 11.7 ppg
1.13 The driller fails to fill the hole when pulling out of the well.
The drilling fluid level drops 580 feet causing the well to flow.
Current drilling fluid density: 11.9 ppg.
True Vertical Depth (TVD): 9500 feet
What is the Bottom Hole Pressure (BHP) when the well starts to flow?
……………………………………..psi
4
1.14 While drilling, there are severe losses. After the pumps are stopped, the
drilling fluid level drops far below the flowline. The well is then filled to the
top with water.
Drilling fluid density: 11.3 ppg
Water density: 8.6 ppg
Volume of water filled into the annulus is 200 feet.
What is the decrease in hydrostatic Bottom Hole Pressure (BHP)?
a. 118 psi
b. 207 psi
c. 28 psi
d. 89 psi
1.15 Calculate the fluid density if the fluid gradient is 0.884 psi/ft
…………………… ppg
1.16 What is the reduction in Bottom Hole Pressure (BHP) if the drilling fluid level
dropped by 800 feet with a density of 10.5 ppg?
…………………… psi
1.17 How much will the Bottom Hole Pressure (BHP) decrease if the annular fluid
drops by 100 feet? The Drilling fluid density is 15 ppg.
……………………psi
1.18 Calculate bottom hole hydrostatic pressure using the information below:
Well Measured Depth (MD): 18575 feet
Well True Vertical Depth (TVD): 16281 feet
Shoe True Vertical Depth (TVD): 12875 feet
Maximum allowable drilling fluid density: 17.8 ppg
Current drilling fluid density: 14.7 ppg
a. 11917 psi
b. 12445 psi
c. 14199 psi
d. 9842 psi
5
Dynamic Pressure
1.19 A vertical well is 6020 feet deep and filled with 11.5 ppg mud.
While circulating at 80 SPM the friction losses in the well system are as follows:
a. 200 psi pressure loss through surface equipment.
b. 680 psi pressure loss in drill string.
c. 1570 psi pressure loss through bit nozzles.
d. 110 psi pressure loss in annulus.
What is the Bottom Hole Pressure (BHP) when the pumps are running at 80 SPM?
……………………psi
1.20 At 40 spm with 10 ppg fluid, the pump pressure is 1000 psi.
What is the pump pressure if the rate is decreased to 25 spm and the fluid
density is increased to 11.4 ppg?
a. 390 psi
b. 445 psi
c. 550 psi
d. 710 psi
6
2. Leak-Off Test
2.1 Calculate the MAASP using the following information:
Well Data:
Casing Shoe depth (TVD): 6800 feet
Maximum Allowable drilling fluid density: 16.7 ppg
Density of drilling fluid in hole: 15 ppg
…………………… psi
2.2 Calculate the formation strength at the casing shoe using the following
information?
Well Data:
Casing Shoe Depth (TVD) 6000 ft
Drilling Mud Density 12 ppg
MAASP 1300 psi
……………………psi
2.3 Calculate the maximum allowable mud weight using the following
Well Data:
Casing shoe depth: 8000 ft, TVD
Leak off test pressure at pump: 1500 psi
Density of drilling mud in hole: 10.4 ppg
……………………ppg
2.4 After conditioning the well with 12 ppg mud, the Driller does a Leak-Off Test
(LOT) at 5000 feet True Vertical Depth (TVD), and records a LOT pressure of
875 psi.
Calculate the maximum allowable mud density.
a. ppg
b. 13.2 ppg
c. 14.5 ppg
d. 15.3 ppg
7
2.5 Given that the Formation strength is 1900 psi, the Casing shoe TVD is 2000 ft,
the Annulus Pressure Losses (APL) is 250 psi;
Calculate the maximum mud density that can be used/circulated, without
causing mud losses.
……………………ppg
……………………psi
2.8 After a leak-off test using 10.3 ppg test fluid, casing shoe fracture pressure is
calculated at 5730 psi.
Maximum anticipated Annular Pressure Loss (APL) at drilling rate for the
section is 350 psi
Casing Shoe True Vertical Depth (TVD) is 8640 feet
What is the maximum drilling fluid density that can be circulated without
losses?
…………………… ppg
8
2.9 The deepest casing shoe in a well is set at 5675 feet MD, 5125 feet TVD. If the
mud density is increase by 1.2 ppg, how will this affect MAASP?
a. It will be 320 psi higher.
b. It will be 320 psi lower.
c. It will be 354 psi higher.
d. It will be 354 psi lower.
9
3. Tripping
3.1 What is the bottom hole hydrostatic pressure reduction when pulling 1000 ft. of
5" drill pipe dry without filling the hole (no mud returning to the well)?
Well Data:
Casing capacity: 0.1522 bbl./ft.
Drill pipe capacity: 0.0178 bbl./ft. Drill pipe steel
displacement: 0.0076 bbl./ft.
Mud density: 11 ppg
a. 51 psi
b. 61 psi
c. 30 psi
d. 101 psi
…………………… psi
……………………psi
10
3.4 Well Data:
TVD: 5643 ft.
MD: 5900 ft.
Formation Pressure: 2770 psi.
Current fluid density: 10.4 ppg
Metal displacement: 0.0075 bbl./ft.
Pipe capacity: 0.0178 bbl./ft.
Casing capacity: 0.0758 bbl./ft.
Stand length: 90 ft.
How many dry stands the Driller to pull out of hole without going underbalance?
a. 11 stands
b. 12 stands
c. 52 stands
d. 53 stands
……………………minutes
11
3.6 A well is shut in with bit 10 stands 930 ft. off bottom. What is the bit to shoe
strokes if a pump capacity of 0.12 bbl./stroke is used to circulate the well?
Well Data:
3.7 A well is shut in with bit 10 stands 930 ft. off bottom. What is the pump to bit
strokes if the pump capacity of 0.12 bbl./stroke is used to circulate the well?
Well data:
3.8 The Driller pulls three stands of drill collars from a well (dry).
Drill collar capacity: 0.0073 bbl/ft
Drill collar metal displacement: 0.0370 bbl/ft
How many barrels of drilling fluid should the Driller pump into the well? (One
stand = 90’)
……………………bbl.
12
3.9 Calculate the volume of drilling fluid required to fill the hole per stand when
pulling ‘wet’, with no drilling fluid returns to the well.
Well Data:
Drill Pipe Capacity: 0.0178 bbl./ft.
Drill Pipe Metal Displacement: 0.0082 bbl./ft.
Average Stand Length: 93 ft.
a. 0.76 bbl.
b. 1.65 bbl.
c. 2.42 bbl.
d. 9.28 bbl.
13
4. Slug
4.1 A driller prepare to pull out of the hole and line up to the slug pit. The driller
then pumps a 20 bbl heavy slug, followed by 10 bbl of drilling fluid from the
active pit.
Well Data:
Depth of hole (TVD): 9200 ft.
Drilling fluid density: 12.2 ppg.
Heavy slug density: 14.5 ppg
Drill pipe capacity: 0.01776 bbl./ft.
Surface line volume: 6 bbl.
How far will the fluid level in the string drop when the well has equalized?
a. 1143 feet
b. 183 feet
c. 213 feet
d. 263 feet
4.2 The Driller pumps a 25 bbl. Heavy slug with a density of 12 ppg before pulling
out of the hole from 10500 ft. True Vertical Depth (TVD). The level in the pipe
decreases falls by 215 ft.
What is the change in Bottom Hole Pressure (BHP) if the original drilling fluid
density was 10.4 ppg?
a. 0 psi
b. 1180 psi
c. 140 psi
d. 20 psi
14
5. Volumetric Method/Stripping
5.1 A vertical well is shut in after there is a gas influx. The kill operation is
delayed, and the influx starts to migrate.
Because of this migration, both drill pipe pressure and casing pressure increase by 300 psi
Well Data:
Well depth: 10000 ft.
Casing shoe depth: 6000 ft.
Drilling fluid density: 11.7 ppg
Open hole/drill pipe capacity: 0.060 bbl./ft.
Casing/drill pipe capacity: 0.065 bbl./ft.
NOTE: Assume there is only drill pipe in the well.
Kick Data:
Original shut in stabilized drill pipe pressure: 800 psi
Original shut in stabilized casing pressure: 1050 psi
Original kick volume: 30 bbl.
How many barrels of drilling fluid should be bled from the well to arrive at the
original bottom hole pressure, before gas migration?
a. 1.31 bbl.
b. 1.32 bbl.
c. 1.36 bbl.
d. 2.16 bbl.
16
6. Various
6.1 Whilst drilling a horizontal well a fault is crossed and a kick is taken. The well is shut in.
Calculate the mud density required to kill the well using the data below:
Well Data:
Depth at start of horizontal section: MD 6500 ft. TVD 4050
Depth at time of kick: MD 10500 TVD 3970
Length of horizontal section: 4000 ft.
Mud density: 11.2 ppg
Kick Data:
Shut In Drill Pipe Pressure: 150 psi
Shut In Casing Pressure: 150 psi
……………………ppg
6.2 While drilling through a fault in the horizontal section of a well, a kick is taken
and the well shut in.
Calculate the new mud density required to kill the well using the data below.
Well Data:
Measured depth at start of horizontal section: 7690 ft.
Measured depth at time of kick: 13680 ft.
True vertical depth at start of horizontal: 5790 ft.
True vertical depth at time of kick: 5820 ft.
Length of horizontal section: 5990 ft.
Mud density: 12.8 ppg
Kick Data:
Shut In Drill Pipe Pressure 230 psi
Shut In Casing Pressure 240 psi
a. 13.1 ppg
b. 13.4 ppg
c. 13.6 ppg
d. 13.7 ppg
17
6.3 A vertical well with a surface BOP stack is shut in after a gas kick.
The bit is 500 feet off bottom and the influx is calculated to be on bottom Shut
in Drill Pipe Pressure (SIDPP) is 250 psi.
What will the Shut In Casing Pressure (SICP) be?
a. Zero
b. 250 psi
c. 750 psi
6.4 A well is shut in after a kick and will be killed using the Wait and Weight Method.
Pre-recorded data:
True Vertical Depth (TVD) of well: 10000 ft.
Total string volume: 1400 strokes
Total annulus volume: 5700 strokes
Kill rate circulating data:
At 30 SPM is 520 psi
Kick data:
Shut-In Drill Pipe Pressure (SIDPP): 480 psi
Shut In Casing Pressure (SICP): 650 psi
Drilling fluid density in the well: 12.0 ppg
What is the Final Circulating Pressure (FCP) at 30 SPM?
a. 564 psi
b. 607 psi
c. 720 psi
d. 752 psi
18
6.5 A well is shut in after a kick and will be killed using the Wait and Weight Method.
Pre-recorded data:
True Vertical Depth (TVD) of well: 10000 ft.
Total string volume: 1400 strokes
Total annulus volume: 5700 strokes
Kill rate circulating data:
At 30 SPM and 12.0 ppg mud weight: 520 psi
Kick data:
Shut In Drill Pipe Pressure (SIDPP): 480 psi
Shut In Casing Pressure (SICP): 650 psi
Drilling fluid density in the well: 12.0 ppg
What is the required kill fluid density?
a. 12.8 ppg
b. 13.0 ppg
c. 13.2 ppg
d. 13.3 ppg
6.6 The well is shut in after a kick, and will be killed using the Wait and Weight Method.
Kill rate circulating date:
At 30 SPM is 520 psi
Shut-in data:
Shut In Drill Pipe Pressure (SIDPP): 480 psi
Shut In Casing Pressure (SICP): 650 psi
Drilling fluid density in the well: 12.0 ppg
Calculate the Initial Circulating Pressure (ICP) at 30 SPM.
a. 1000 psi
b. 1070 psi
c. 1130 psi
d. 1170 psi
19
Model Answers
1.1 A
Formation Pressure Gradient = Pressure / Depth
= 601 / 1200
= 0.5 psi/ft. > 0.465 psi/ft.
1.2 C
Pressure at the top of the reservoir = Pressure at the gas/water contact – Gas hydrostatic
= (3950 x 0.464) – {(3950-3470) x 0.1}
= 1832.8 – (480 x 0.1)
= 1832.8 – 48
= 1874.8 psi
1.3 Reduction in Hydrostatic pressure = Level Drop x Mw x 0.052
= (10bbl/hr x 3 hours / 0.073) x 10.8 x 0.052
= 410.958 x 10.8 x 0.052
= 230.79 psi
1.4 Bottom Hole Pressure = Mw x Well TVD x 0.052
= 14.7 x 16281 x 0.052
= 12445 psi
1.5 B
1.6 Expected Reservoir Pressure = Hydrostatic Pressure – Swab Pressure
= (9500 x .052 x 10) - 250
= 4940 - 250
= 4690 psi
1.7 Final Bottom-hole pressure = (Mud density + cuttings density) x .052 x TVD
= (9.8 + 0.2) x .052 x 5000
= 10 x .052 x 5000
= 2600 psi
20
1.8 Mud density with trip margin included = Equation Number 8
= (250 / 9200 / .052) + 10.6
= 11.12 ppg
1.9 D
Drilling Fluid Density with Trip margin = (Formation pressure + Trip Margin) / (0.052 x TVD)
= (4430 + 250) / (8350 x 0.052)
= 4680 / 434.2
= 10.77 psi
1.10 Drilling Fluid density with trip margin = Current Mw + [Trip Margin / (TVD x 0.052)]
= 12.3 + ({350 / (14650 x 0.052)}
= 12.3 + (350 / 761.8)
= 12.75 – 12.8 ppg
1.11 Increase in BHP = Increase in Trip Margin x .052 x TVD
= 0.5 x .052 x 8300
= 215- 216 psi
1.12 Mud density with trip margin included = Equation Number 8
= (287 / 9200 / .052) + 10.6
= 11.19 ppg
1.13 Bottom-hole pressure = New drilling fluid level x .052 x Mud density
= (9500 – 580) x .052 x 11.9
= 8920 x .052 x 11.9
= 5519.69 – 5520 psi
1.14 Decrease in hydrostatic pressure = (Mud density – Water density) x water height x 0.052
= (11.3 - 8.6) x 200 x 0.052
= 28 psi
1.15 Mud density = Mud gradient / .052
= .884 / .052
= 17 ppg
21
1.16 Reduction in BHP = Reduction in Hydrostatic pressure
= Reduction in drilling fluid level x .052 x Mud density
= 800 x .052 x 10.5
= 436.8 – 437 psi
1.17 BHP drop = Level drop x Mw x 0.052
= 100 x 15 x 0.052
= 78 psi
1.18 Hydrostatic Pressure = Well TVD x .052 x Mud density
= 16,281 x .052 x 14.7
= 12,445.19 psi
1.19 BHP while circulating = Hydrostatic Pressure + APL
= (6020 x 0.052 x 11.5) + 110
= 3709.96 - 3710 psi
1.20 Equations 9 and 10
New Pump pressure = Old pump pressure x (New Mw / Old Mw) x (New SPM / Old Spm)2
= 1000 x (11.4 / 10) x (25 /40)2
= 445 psi
2.1 MAASP = (Maximum Mud Weight – Current Mud Weight) x Shoe TVD x 0.052
= (16.7 – 15) x 6800 x 0.052
= 601 – 601.12 psi
2.2 Formation Strength = MAASP + Hydrostatic Pressure above casing shoe
= 1300 + (6000 x .052 x 12)
= 1300 + 3744
= 5044 psi
2.3 Maximum Allowable Mud density = Equation Number 11
= (1500 / 8000 / .052) + 10.4
= 14 ppg
22
2.4 D
Maximum Mud density = Test Mud Weight + [LOT pressure / (Shoe TVD x 0.052)]
= 12 + {875 / (5000 x 0.052)}
= 12 + (875 / 260)
= 15.36 ppg
2.5 Maximum Allowable Mud density with APL = (Formation Strength – APL) / (TVD x .052)
= (1900 – 250) / (2000 x .052)
= 1650 / 104
= 15.8 – 15.86 ppg
2.6 MAASP = Equation Number 12
= (Maximum Allowable Mud density – Current Mud density) x .052 x Shoe TVD
*Maximum Allowable Mud density = Formation Strength Gradient / .052
= .707 / .052
= 13.5 – 13.59
*MAASP = (13.5 - 10) x .052 x 7400
= 3.5 x .052 x 7400
= 1346 – 1346.8 psi
*MAASP = (13.59 -10) x .052 x 7400
= 3.59 x .052 x 7400
= 1381 – 1381.4 psi
MAASP = Formation Strength - Hydrostatic Pressure above casing shoe
= (Formation Strength gradient x Shoe TVD) - Hydrostatic Pressure above casing shoe
23
2.8 Fracture Pressure including safety margin = Fracture pressure at test – APL
= 5730 – 350
= 5380 psi
Maximum fluid density for circulation = Fracture pressure with safety / (Shoe TVD x 0.052)
= 5380 / (8640 x 0.052)
= 11.9 - 11.97 ppg
2.9 B
MAASP change = Hydrostatic Pressure change above casing shoe
= Mud weight change above casing shoe x .052 x TVD
= +1.2 x .052 x 5125
= +319.8 psi
The hydrostatic increased, then the MAASP should decrease by 319.8 – 320 psi
2.10 D
Maximum Mud weight = Mud weight at test + [LOT pressure / (Shoe TVD x 0.052)]
= 12.8 + {380 / (5560 x 0.052)
= 14.11 ppg
MAASP with mud weight 13.5 ppg = (Maximum Mw – Current Mw) x Shoe TVD x 0.052
= (14.11 – 13.5) x 5560 x 0.052
= 177 psi
Safety Margin = MAASP – SICP
= 177 – 180
= -3 psi (No margin)
3.1 Pressure drop after pulling dry pipe = Equation Number 19 x Length of pipe
24
3.2 Pressure drop after pulling dry pipe = Equation Number 19 x Length of pipe
= (10 x 0.052 x 0.0075) / (0.0758 – 0.0075) x (10 x 93)
= (0.0039 / 0.0683) x 930
= 53 - 53.1 psi
3.3 Formula #20:
Pressure Drop = (Mw x 0.052 x Closed End) / (Casing Capacity – Closed End)
Closed End = Metal displacement + Internal capacity
= 0.0075 + 0.0178
= 0.0253 bbl./ft.
Pressure Drop = (10 x 0.052 x 0.0253) / (0.0758 – 0.0253)
= 0.013156 / 0.0505
= 0.26 psi/ft.
Total pressure drop = 0.26 x 10 stands x 93 feet = 241.8 – 242 psi
3.4 C
Formula #23
Lg. dry tubulars = Overbalance x [CSG Cap. – Metal Displ.] / 0.052 x Mw x Metal Displ.
= 3051.7 – 2770
= 281 psi
= 4731.8 ft.
= 4731.8 / 90
= 52.58 stands
= 4672-4673 strokes
*Time = 4673 / 30
26
Surface line strokes = Surface line volume / Pump Output
= 12 / 0.12
= 100 strokes
Pump to bit strokes = 1197 + 48 +
100
= 1345 strokes
3.8 Volume of mud (dry) = Drill Collar Metal Displacement x Drill Collar Pulled Length
= 0.0370 x (3 x 90)
= 9.99 bbl.
3.9 Volume to fill the hole ‘wet’ = Stand length x Closed End displacement
= 93 x (0.0178 + 0.0082)
= 2.418 – 2.42 bbl.
4.1 Level Drop due to slug = Pit Gain / Drill Pipe Capacity
*Pit Gain due to slug = Equation Number 27
= 20 x ((14.5/12.2) -1)
= 20 x (1.1885 -1)
= 3.77 bbl.
*Level Drop due to slug = 3.77 / .01776
= 212.3 ft.
4.2 A
27
5.2 D
Formula #17
Gas Migration Rate = Rate of increase in pressure per hour / (Mw x 0.052)
= (100 x (60/15)) / (15 x 0.052)
= (100 x 4) / (15x 0.052)
= 512.82 ft./hr.
5.3 Pressure Increase due to gas migration = Migration Distance x .052 x Mud density
= 600 x .052 x 12.8
= 399.36 – 400 psi
*SIDPP = 530 + 400
= 930 psi
*SICP = 680 + 400
= 1080 psi
6.1 Kill Mud Density = Equation Number 13
= (SIDPP / TVD at time of kick / .052) + Original Mud density
= (150 / 3970 / .052) + 11.2
= 11.92 – 12 ppg
6.2 Kill Mud Density = Equation Number 13
= (SIDPP / TVD at time of kick / .052) + Original Mud density
= (230 / 5820 / .052) + 12.8
= 13.55 – 13.6 ppg
6.3 Off Bottom SIDPP = Off Bottom SICP
= 250 psi
6.4 A
Final Circulating Pressure = (Kill Mw / Current Mw) x RRCP
Kill Mud Density = Current Mw + {SIDPP / (TVD x 0.052)}
= 12 + {480 / (10000 x 0.052)}
= 12 + 0.92
= 12.92 - 13 ppg
FCP = (13 / 12) x 520
= 563.3 – 564 psi
28
6.5 B
Kill Mw = Current Mw + {SIDPP / (TVD x 0.052)}
= 12 + {480 / (10000 x 0.052)}
= 12.93 – 13 ppg
6.6 A
Initial Circulating Pressure = SIDPP + RRCP
= 480 + 520 = 1000 psi
29