106

(Clamping system)
(L1)

(Motor shaft)
24 47 35
(L22) 60
3 (Q3)
+2
M 5 x8 0
8 30
M 5 x12+2
80
0

(D20)
(G3)

)
23
11

(D
pc
d.
(D
22 63
)
. 52
pcd

40 h7
40+0.05
+0.02

17

60
(D21)
+0,1
R0,4-0,1

14 h7
3.4
(L21)
+1,5
23 +0,3
(L20)

Materials / Surfaces:
Input flange: Aluminum / untreated
Housing: Steel / heat-treated and post-oxidized (black)
Output flange: Aluminum / untreated

Hints:
Please pay attention to the operating and mounting instructions.
Subject to modifications.

Variables on the drawing are dependent upon the motor.

The given dimensions are exemplary.

Scale: 1:1 DIN A3 ISO

NEUGART Revision status: M from: 11/2023
Changed revision status: L from: 07/2022

General
PLE060-aii-SSSB3AC-Y(D20)
tolerance
DIN ISO 2768-cL /(L20)/(D21)/(D22)/B5/(G3)

Neugart GmbH
Keltenstr. 16 Sheet 1/2
D-77971 Kippenheim
 General gearbox data Character Unit

Planetary gearbox - gearing type - - Straight teeth

0,2 x Mb
Rotation direction - - Input and output in the same direction (1) Max. motor weight* in kg =
motor length in m
Number of stages p - 1-stage
Output shaft bearing - - Deep groove ball bearing * with symmetrically distributed motor weight
Service life (L10h) tL h 30.000 * with horizontal and stationary mounting
Max. operating temperature T min / T max °C -25 / +90
Protection class - - IP 54
Lubrication (lifetime lubrication) - - Standard lubrication (Klübersynth GE 14-112)
Installation position - - Any
Max. bending moment based on the gearbox input flange Mb Nm 12
(for motor weight) (1)
Motor shaft concentricity / Coaxiality and axial runout Motor flange- mm 0,03 / 0,06 (Measuring methods according to operating manual)
Required motor shaft tolerance - - j6; k6
Min. permissible motor shaft length L20 min mm 14,5
Reference operating mode - - S1
Reference operating factor KA - 1
Reference speed n2 rpm 100
Reference ambient temperature T Amb °C 20
Radial force for output bearing Fr 20.000h N 400
based on shaft center after L10h=20,000h with Fa=0N
Axial force for output bearing Fa 20.000h N 500
based on gearbox axis after L10h=20,000h with Fr=0N
Radial force for output bearing Fr 30.000h N 340
based on shaft center after L10h=30,000h with Fa=0N
Axial force for output bearing Fa 30.000h N 450
based on gearbox axis after L10h=30,000h with Fr=0N
Maximum radial force Fr Max N 700
based on shaft center and T2=0Nm
Maximum axial force Fa Max N 800
based on gearbox axis and T2=0Nm

Ratio-dependent gearbox data Character Unit

Ratio
aii - 3 4 5 7 8 10

Nominal output torque T 2N Nm 28 38 40 25 18 15

Max. output torque T 2max Nm 45 61 64 40 29 24

for 30,000 output shaft rotations
Emergency stop torque T2Stop Nm 66 88 80 80 80 80
permitted 1000 times
Average idle torque T0 Nm 0,15 0,1 0,1 0,1 0,1 0,1
for n1=3,000 rpm and 20 °C gearbox temperature
Average thermal input speed at 50% T2N, S1, and T_Amb n 1N 50% rpm 4500 4500 4500 4500 4500 4500
Operating temperature may not be exceeded!
Average thermal input speed at 100% T2N, S1, and T_Amb n1N 100% rpm 4500 4500 4500 4500 4500 4500
Operating temperature may not be exceeded!
Max. mechanical input speed n1 Limit rpm 13000 13000 13000 13000 13000 13000
Operating temperature may not be exceeded!
Torsional backlash jt arcmin < 10 < 10 < 10 < 10 < 10 < 10
based on output shaft
Torsional stiffness cg Nm/arcmin 2,5 2,7 2,8 2,5 2,4 2,2
based on output shaft
Efficiency
h % 98 98 98 97 97 96 Subject to modifications.
at T2N, gearbox temperature 70 °C and n1=1,000rpm
Running noise Qg dB(A) 58 58 58 58 58 58
at n1=3,000 rpm without load at a distance of 1m
Gearbox weight mG kg 0,9 0,9 0,9 0,9 0,9 0,9 NEUGART
Mass moment of inertia
J kgcm² 0,128 0,092 0,08 0,069 0,067 0,065
based on clamping system diameter input

PLE060-aii-SSSB3AC-Y(D20)
/(L20)/(D21)/(D22)/B5/(G3)

Sheet 2/2

Revision status: M from: 11/2023