Unit No.

4900
Baker Oil Tools Index: 305.00
Date: April 7, 2000
REMEDIAL SYSTEMS Page:1 of 10
TECHNICAL UNIT

Wireline Feelers, Junk Catchers, and Wireline Jars

Product Family Nos. H43901, H43907, and H43944

Introduction

Model “H” Wireline Feeler and Junk

Catcher, Product Family No. H43901
The Wireline Feeler and Junk Catcher is run in
the well to determine if the well bore is large
enough to permit subsequent passage of the
Bridge Plug, Retainer, Packer or other pack-off
tool that is to be run. In addition, the Feeler and
Junk Catcher will serve to clean the well of junk
that might otherwise foul the tool and cause a pre-
mature set.

Model “R” Wireline Feeler and Junk

Catcher, Product Family No. H43907
The Baker Model “R” Wireline Feeler and Junk
Catcher is used to gage the inside of 2-3/8", 2-7/8"
and 3-1/2" tubing and clean the hole of junk prior to
running Wireline Packers, Retainers and Bridge
Plugs.
In those wells where large particles or unusual-
ly high quantities of junk are present, it is recom-
mended that the Baker Model “C” Wireline Jar be
run immediately above the Model “R” Wireline
Feeler and Junk Catcher.

Model “C” Wireline Jar, Product Family

No. H43944
The Size 05 Model “C” Wireline Jar is designed
to be run immediately above the Baker Model “R”
Wireline Feeler and Junk Catcher, especially in
those wells where large particles or unusually high
quantities or junk are present.

Drawing No. 439-01

This document contains Confidential Information of Baker Hughes Incorporated (Baker) and is furnished to the customer for information purposes only. It is
requested that this document not be reproduced in any way whatsoever, in part or in whole, or distributed outside the customer organization without first obtaining
the express written authorization of Baker. This document is the property of Baker and returnable on request of Baker.  April, 2000, Baker Hughes Incorporated.
 Unit No. 4900 4-7-00 Wireline Feelers, Junk Catchers, and Wireline Jars
Index: 305.00 Page 2 of 10

as necessary until no more junk is retrieved and it

WARNING is felt that the well fluid is clean.
Use of Baker equipment contrary to
manufacturer’s specification may result in Gage Rings
property damage, serious injury or fatality.
Baker Gage Rings are currently being steel
stamped with Material Number and OD only. The
Model “H” Wireline Feeler and Junk practice of identifying them by size as well as Ma-
Catcher, Product Family No. H43901 terial Number will therefore be discontinued as
soon as practical.
Assembly
The Gage Ring OD, in all cases, is slightly larg-
Assembly of the Model “H” Wireline Feeler and
er than the Packer, Bridge Plug or Retainer, ensur-
Junk Catcher may be readily discerned from Draw-
ing that the tool will pass through any tight spots in
ing No. 752-152.
the casing that can be passed by the Gage Ring.
NOTE: Size 1BB Cement Retainer Gage Rings are
NOTE: In Packer sizes the same Gage Ring is used for
available for either size 10 or 20 Wireline Feeler and
“odd” size packers.
Junk Catcher. Size 3AA Cement Retainer Gage Rings
are available for either size 20 or 25 Wireline Feeler and Checking of Firing Head After Run With
Junk Catcher. Be sure that you have the correct Gage Wireline Feeler and Junk Catcher - Extreme
Ring for the size Feeler and Junk Catcher. Temperature Only
Operating Instructions After running the Wireline Feeler and Junk
Make up the proper size Firing Head (Product Catcher on the Firing Head, the Cartridge Seat,
Family No. H43720) with Igniter (Product Family Cartridge Seat Cap and Igniter Assembly must be
No. H43744) installed (extreme temperature only), removed from the Firing Head to check for possi-
onto the electric line. Make up the assembled ble fluid leaks and high-temperature firing of the Ig-
Wireline Feeler and Junk Catcher onto the Firing niter. If the Igniter has been fired by high well
Head tong-tight with the Spanner Wrench (part of temperature it will be impossible to run the Wireline
the Wireline Pressure Setting Assembly). Pressure Setting Assembly to the setting depth
without danger of a premature set. If any fluid is
NOTE: When running a size 10 Model “H” Wireline
found inside the Firing Head all parts must be
Feeler and Junk Catcher on a size 20 Firing Head, the
Electric Line Adapter Sub, Material Number H01- dried, sealing surfaces examined, and all O-rings
24458-00, must be used as a Crossover Sub. inspected and replaced. It is very important that all
new O-rings be used when the Wireline Pressure
The reason for installing the Firing Head Igniter Setting Assembly is run, as fluid around the Pin
is to check whether or not the temperature in the would prevent the Firing Head from operating. Do
well will be sufficient to set off the Igniter. Should not reuse the Igniter! Discard and use a new Ignit-
this occur, it will be impossible to run the Wireline er.
Pressure Setting Assembly to the desired depth
without danger of a premature set. Wear Allowances for Gage Rings
After checking to be sure that the proper size The Specification and Interchangeability Guide
Gage Ring corresponding to the size pack-off tool on the following pages gives the minimum diame-
to be run is installed, the Wireline Feeler and Junk ters to which Gage Rings may wear and still be us-
Catcher is run into the well to a point slightly below able. Gage Rings should be replaced after they
the setting depth of the pack-off tool to check the have become worn below the “Minimum Wear OD”
gage of the well. shown in the following charts.

It is necessary that the Feeler and Junk Catcher

be run in the hole at a rate of speed in excess of
150 feet per minute in order to hold the Body off the
Valve and allow the entry of fluid and junk into the
Catcher. If junk is retrieved from the well, the Feel-
er and Junk Catcher should be run as many times
Model “H” Wireline Feeler and Junk Catcher, Product Family No. H43901

Wireline Feelers, Junk Catchers, and Wireline Jars

Assembly and Dimensional Data Drawing No. 752-152

Index: 305.00
Unit No. 4900
Page 3 of 10
4-7-00
Unit No. 4900 4-7-00 Wireline Feelers, Junk Catchers, and Wireline Jars
Index: 305.00 Page 4 of 10

Model “H” Wireline Feeler and Junk Catcher, Product Family No. H43901
Dimensional Data
Refer to Drawing No. 752-152.
Size
Dim
10 20 25
A 2.750 3.375
B 2.208 2.709
C 1.750 2.250
D 2.00 2.44
E 3.87 4.19
F 6.00 7.31
G 2.250
H 1.750
-
J 1.56
K 18.00
L 0.875 1.25
M 7.12 6.75
N 0.750 1.602
P 1.250 3.000
Q 2.750 4.000 5.500
R 1.00 1.50
S 6.00 5.40 3.50
T 66.37 66.06 67.56
U 2.250 3.250 4.625
X
See Spec Charts 1 and 2
Y
Z 46.06 45.12 46.65
AA 2.37 4.06 5.56
BB 3/8 Std. Pipe Thd. 3/4 Std. Pipe Thd.

Parts List
Refer to Drawing No. 752-152.
No.
Item No. Description Size 10 Size 20 Size 25
Req’d
1 Electric Line Adapter Bar o 1 H01-24458-00 -
2 Sinker Bar Adapter * 1 - H01-20803-00 t
3 Electric Line Adapter * 1 H01-23785-00 H01-20614-00
4 Mandrel 1 H01-33162-00 H01-33163-00
5 Screen 1 H01-20581-00 H01-20611-00
HWW-G118-0S0 HWW-G11B-0M0
6 Socket Head Cap Screw ** -
(1/4 - 20 x 3/4 lg) [2] (5/16 - 18 x 5/8) [3]
7 Upper Guide 1 H01-24651-00 H01-24167-00
8 Body 1 H01-23524-00 H01-23870-00 H01-23871-00
9 Gage Ring with Screw 1 See Charts 1, 2, and 3
10 Valve with Screw 1 H01-30613-00 H01-33161-00 H01-33160-00
Ref. Item HWW-G518-0M0
11 Socket Head Set Screw H01-33450-00 H01-87384-00
10 (1/4 - 20 x 5/8 lg)
t Optional Sinker Bar Adapter with 3/4 Sucker Rod may be used. Material No. H01-20803-01.
* Use 1 of either items 2 or 3.
** See Size for No. Required.
o This part is used to connect the #10 Wireline Feeler and Junk Catcher to the #20 Firing Head when running number
23 or 32 Packers of 1AA or 1BB Retainer or Bridge Plug.
Wireline Feelers, Junk Catchers, and Wireline Jars Unit No. 4900 4-7-00
Index: 305.00 Page 5 of 10

Model “H” Wireline Feeler and Junk Catcher, Product Family No. H43901

Specifications for Cement Retainer and Bridge Plug Gage Rings

Chart No. 1
Tool Size Gage Ring
Size Wireline Feeler K-1, N-1, NC-1 Original Length
Material No. Min Wear
and Junk Catcher and S (X) (Y)
040 H01-81714-00 3.171 3.140 2.0
10 1AA H01-81361-00 3.625 3.593 1.9
H01-49909-00 3.968 3.937 2.6
1BB
H01-81617-00 4.000 3.968 2.5
20 2AA H01-81362-00 4.343 4.312 2.1
2BB H01-44148-00 4.968 4.937 2.4
3AA H01-81363-00 5.500 5.468 1.8
3BB H01-30433-00 5.718 5.687 2.0
4AA H01-30436-00 6.343 6.312 2.6
5AA H01-81365-00 7.152 7.125 2.7
6AA H01-81366-00 8.156 8.125
25 3.1
6BB H01-83786-00 9.031 9.000
7AA H01-32069-00 9.468 9.437 5.8
8AA H01-81367-00 10.468 10.437 6.3
8BB H07-51707-00 11.625 11.593
6.7
9AA H01-81368-00 12.031 12.000
Unit No. 4900 4-7-00 Wireline Feelers, Junk Catchers, and Wireline Jars
Index: 305.00 Page 6 of 10

Model “H” Wireline Feeler and Junk Catcher, Product Family No. H43901

Specifications for Production Packer Gage Rings

Chart No. 2
Tool Size Gage Ring
Size Wireline Feeler Original Length
Packer Size Material No. Min Wear
and Junk Catcher (X) (Y)
13 H01-36662-00 3.093 3.062
15 H01-36661-00 3.218 3.187 2.00
19 H07-56414-00 3.500 3.468
21 H01-81361-00 3.625 3.593 1.93
10
22 and 28 H01-63932-00 3.687 3.656 2.31
23 H01-83129-00 3.781 3.750 2.25
24 H01-63933-00 3.875 3.843 2.31
H01-30489-00 2.50
32 4.031 4.000
H01-29733-00 2.00
34 H01-29732-00 4.312 4.281 2.12
42 H01-44147-00 4.406 4.375
2.18
43 H01-29722-00 4.500 4.468
44 H01-29720-00 4.656 4.625
20 2.31
45 H01-44145-00 4.625 4.593
47 H01-29730-00 4.812 4.781 2.56
64 H01-29719-00 5.000 4.968 2.43
81 H01-81618-00 5.406 5.375 2.87
82 H01-29723-00 5.531 5.500 2.93
83 H01-30433-00 5.718 5.687 2.00
84 H01-30441-00 5.781 5.750 2.12
85 H01-30434-00 5.937 5.906 2.06
86 H07-52252-00 6.000 5.968
2.12
87 H01-30435-00 6.062 6.031
88 and 89 H01-30436-00 6.343 6.312 2.62
89S and 92 H01-30443-00 6.468 6.437 3.00
91 H01-30437-00 6.593 6.562 2.37
25
126 H01-30445-00 7.343 7.312 2.81
128 H01-30438-00 7.656 7.625 2.87
192F and 194D and S H01-30439-00 8.281 8.250
194F H02-07137-00 8.500 8.468 3.18
212 H01-83786-00 9.031 9.000
214 H01-32069-00 9.468 9.437 5.87
220 H01-81367-00 10.468 10-437 6.37
240 H01-81368-00 12.031 12.000 6.75
Wireline Feelers, Junk Catchers, and Wireline Jars Unit No. 4900 4-7-00
Index: 305.00 Page 7 of 10

Model “H” Wireline Feeler and Junk Catcher, Product Family No. H43901
Specifications for “D” and “DA” Lok-Set Retrievable Casing Packer
Chart No. 3
Size Wireline Feeler Packer Gage Ring
and Junk Catcher Size OD Material No. Original OD Min. Wear Width
43A 3.813 H01-63933-00 3.875 3.844 2.313
10
H01-30494-00 2.625
43B 4.125 4.156 4.125
H01-29734-00 2.063
43C 4.250 H01-29732-00 4.313 4.281 2.125
45A2 4.500 H07-52248-00 4.531 4.500 2.188
20
45B 4.781 H01-29730-00 4.813 4.781 2.563
45C 5.063 H07-52250-00 5.094 5.063
2.750
45D 5.156 H01-29727-00 5.188 5.156
47A4 5.813 H07-52251-00 5.844 5.813
2.125
47B2 5.969 H07-52252-00 6.000 5.969
47B4 6.078 H07-52253-00 6.109 6.078 2.188
47C2 6.266 H07-52254-00 6.297 6.266 2.625
47C4 6.453 H07-52255-00 6.484 6.453
3.000
47D4 6.672 H07-52256-00 6.671 6.640
25
49A2 7.313 H01-30445-00 7.344 7.313 2.813
49A4 7.531 H07-52258-00 7.563 7.531 2.875
49B 7.906 H01-30446-00 7.813 7.781 3.750
51A 8.281 H01-32068-00 8.313 8.281 4.938
51B2 8.438 H02-07137-00 8.500 8.469
3.188
51B4 8.609 H07-52259-00 8.641 8.609

Model “R” Wireline Feeler and Junk Operation

Catcher, Product Family No. H43907 The Size 05 Model “C” Firing Head (Product
Family No. H43721) is made up onto the electric
Construction
line. The Wireline Feeler and Junk Catcher is then
The thread on the pin up of the Size 05 Model made up tong-tight to the Firing Head with the
“R” Wireline Feeler and Junk Catcher mates with Spanner Wrench (Part of the Wireline Pressure
the box thread in the Size 05 Firing Head. An O- Setting Assembly).
ring is installed on the pin below the thread, which
seals in the box down on the Firing Head and pro- The complete assembly is then run into the well
tects the Firing Head from well fluids. This arrange- to a point slightly BELOW the setting depth of the
ment eliminates the need for special adapters. pack-off tool (to check the gage of the well) and is
then retrieved. The Wireline Feeler and Junk
A Flapper Valve is installed in the bottom of the Catcher should be run as many times as neces-
Wireline Feeler and Junk Catcher to permit junk sary to ensure that the well is sufficiently cleaned
and fluid to enter the Lower Body and then to trap of all junk and debris that could foul the pack-off
and hold the junk. tool that is to be set.
 Model “R” Wireline Feeler and Junk Catcher, Product Family No. H43907

Index: 305.00
Unit No. 4900
Assembly and Dimensional Data Drawing No. 156-905

Page 8 of 10
4-7-00
Wireline Feelers, Junk Catchers, and Wireline Jars
Dimensional Data
Refer to Drawing No. 156-905.
Size
Dim
05-23 05-27 05-28 05-33 05-35
A 1.660 1.900
B 1.380 1.610
C 1.761 1.968 2.235 2.597 2.800
D 3.000 3.625 4.312 4.750
E 53.50 54.12 54.81 55.25

Parts List
Refer to Drawing No. 156-905.
Item No. Size and Material No.
Description
No. Req’d 05-23 05-27 05-28 05-33 05-35
1 O-ring 1 HWW-B214-H40
2 Top Sub 1 H01-55446-00 H01-55447-00
HWW-G60B-080
3 Hex Socket Set Screw 2
(10 - 32 x 1/4 lg)
4 Body 1 H01-52139-00 H01-52180-00
5 Hex Socket Set Screw 1 - HWW-G60B-080
6 Flapper Valve Assembly 1 H01-52142-00 H01-52523-00
7 Guide 1 H01-52143-00 H07-51754-00 H01-52182-00 H01-55444-00 H01-55445-00
Wireline Feelers, Junk Catchers, and Wireline Jars Unit No. 4900 4-7-00
Index: 305.00 Page 9 of 10

Model “C” Wireline Jar, Product Family the need for special adapters when running the
No. H43944 Wireline Jar above the Wireline Feeler and Junk
Catcher.
Construction
The Model “C” Wireline Jar has almost two feet
The thread on the pin up of the Size 05 Model of stroke available to facilitate retrieving the Model
“C” Wireline Jar mates with the box thread in the “R” Wireline Feeler and Junk Catcher.
Size 05 Firing Head. An O-ring is installed on the
pin below the thread, which seals in the box down Operation
on the Firing Head and protects the Firing Head The operation is the same as for the Model “R”
from well fluids. Wireline Feeler and Junk Catcher except that the
top of the Model “C” Wireline Jar is connected to
The thread in the box down of the Wireline Jar
the Size 05 Model “C” Firing Head, and the bottom
with the pin up of the Model “R” Wireline Feeler
of the Model “C” Wireline Jar is connected to the
and Junk Catcher. This arrangement eliminates
Model “R” Wireline Feeler and Junk Catcher.

Specification Guide
Refer to Drawing No. 155-451.
Wireline Feeler and
Tubing Guide
Junk Catcher Material No.
OD Wt in Lbs Size Size OD
2-3/8 4.6 - 4.7 05 - 23 05 - 23 1.781 H01-52143-00
7.9 - 10.7 05 - 27 05 - 27 1.968 H07-51754-00
2-7/8
6.4 - 6.5 05 - 28 05 - 28 2.235 H01-52182-00
10.3 - 13.5 05 - 33 05 - 33 2.597 H01-55444-00
3-1/2
5.75 - 9.3 05 - 35 05 - 35 2.800 H01-55445-00
 Index: 305.00 Page 10 of 10
Unit No. 4900
Model “C” Wireline Jar, Product Family No. H43944
Assembly and Dimensional Data Drawing No. 155-451

4-7-00
Wireline Feelers, Junk Catchers, and Wireline Jars
Dimensional Data Parts List
Refer to Drawing No. 155-451 Refer to Drawing No. 155-451.
Dim Size 05 Item No. Size and Material No.
Description
A 1.500 No. Req’d Size 05
B 1.000 1 O-ring 1 HWW-B214-H40
C 1.660 2 Top Sub 1 H01-52197-00
D 1.380 HWW-G51B-080
3 Hex Socket Set Screw 1
E 5.000 (5/16 - 18 x 1/4 lg)
F 33.44 4 Mandrel 1 H01-52135-00
G 38.44 5 Retaining Nut 1 H01-52136-00
G* 59.44 HWW-G60B-080
6 Hex Socket Set Screw 2
*In extended position. (10 - 32 x 1/4 lg)
7 Body 1 H01-52137-00
HWW-G60B-080
8 Hex Socket Set Screw 2
(10 - 32 x 1/4 lg)
9 Bottom Sub 1 H01-55454-00