Product Name: Hydrex 2529

MSDS Code: HYS2529

MATERIAL SAFETY DATA SHEET

1 – CHEMICAL PRODUCT AND COMPANY IDENTIFICATION

Product Name: Hydrex 2529

Product Application: Corrosion Inhibitor

Manufacturer: Veolia Water Solutions & Technologies, Saudi – Chemical Industries

P.O. BOX 58515, Riyadh 11515, Kingdom of Saudi Arabia
Telephone: 011 478 77 21. Fax: 011 478 25 60
www.veoliawaterst.com

Emergency Telephone Number:

Riyadh - KSA 011 478 77 21

2 – COMPOSITION INFORMATION ON INGREDIENTS

Chemical Name CAS No. EC No. %

Sodium Molybdate 7631-95-0 231-551-7 3.0 – 8.0%

3 – HAZARDS IDENTIFICATION

Potential Health Effects:

Likely routes of exposure: Eye and skin contact.
Eye contact: Slightly irritating to eyes.
Skin contact: Slightly irritating to skin.
Inhalation: No information available.
Ingestion: Harmful if swallowed

4 – FIRST AID MEASURES

As a general rule, in case of doubt or if symptoms persist, always call a doctor. NEVER induce swallowing in an unconscious
person.
If in eyes: Wash thoroughly with soft, clean water for 15 minutes holding eyelids open. Refer the patient to an
ophthalmologist, in particular if there is any redness, pain or visual impairment.

If on skin: Wash thoroughly with water.

Immediate first aid is not likely to be required. If symptoms occur, remove to fresh air.
If inhaled:
If swallowed: If the quantity is small (no more than one mouthful), rinse the mouth with water and consult a doctor
immediately.

5 – FIRE- FIGHTING MEASURES

Flash Point: Non flammable.

Extinguishing Media: Water spray, foam, dry chemical, or carbon dioxide.
Fire & Explosion Procedures: Move container from fire area if it can be done without risk. Cool containers exposed to
flames with water until well after the fire is out. Keep run-off water out of sewers and
water sources. Dike for water control.

6 – ACCIDENTAL RELEASE MEASURES

Personal Precautions: Use personal protection recommended in section 8.

Environmental Precautions: Keep out of drains and water courses.
Spill Clean up Methods: Contain large spills with dikes and transfer the material to appropriate containers for

Revision No.: 00
Revision Date: 01-01-2019 Page 1 of 4
 Product Name: Hydrex 2529
MSDS Code: HYS2529

reclamation or disposal. Absorb remaining material or small spills with an inert material and
then place in a chemical waste container. Flush spill area with water.

7 – HANDLING AND STORAGE

Handling:
Observe precautions stated on label and also industrial safety regulations. Avoid contact of product with the skin and eyes.
Smoking, eating and drinking are prohibited in premises where the preparation is used.
Emptied containers retain vapour and product residue. Observe all recommended safety precautions until container is cleaned,
reconditioned or destroyed. The reuse of this material's container for non industrial purposes is prohibited and any reuse must
be in consideration of the data provided in this material safety data sheet.

Storage:
Keep the container tightly closed in a dry place.

8 – EXPOSURE CONTROLS/PERSONAL PROTECTION

Protective Equipment:

Eye Protection: Wear safety goggles. Provide eye washes in workshops where the product is constantly handled.
Hand protection: Wear protective gloves.
Body Protection: Although this product does not present a significant skin concern, minimize skin contamination by
following good industrial practice. Wash thoroughly after handling.
Respiratory Protection: Not required.
Ventilation: Provide natural or mechanical ventilation to minimize exposure.

9 – PHYSICAL AND CHEMICAL PROPERTIES

Appearance : Clear
State : Liquid
Color : Pale yellow
Odor Characteristic : Not specified
pH of concentrate : 12.5 – 14.0
Specific Gravity @ 25oC : 1.18 – 1.25
Viscosity, cps : As water
Melting Point, (oC) : Not specified
Boiling Point, (oC) : 100
Percentage Volatility, (%) : Not specified
Solubility in Water : Complete

10 – STABILITY AND REACTIVITY

Stability: Stable under proper storage conditions

Conditions to avoid: None known
Material to avoid: Acids
Hazardous decomposition products: None known

11 – TOXICOLOGICAL INFORMATION

No data is available regarding the preparation itself.

It is generally agreed that substances contained are likely to cause the appearance of major lesions which persist for at least
twenty-four hours after application to the eye of an animal. And are likely to cause significant irritation which lasts twenty-four
hours after application to the healthy, unbroken skin of an animal for a period of up to 4 hours.

12 – ECOLOGICAL INFORMATION

No ecological data on the product itself is available.

Revision No.: 00
Revision Date: 01-01-2019 Page 2 of 4
 Product Name: Hydrex 2529
MSDS Code: HYS2529

The product must not be allowed to run into drains or waterways.

13 – DISPOSAL CONSIDERATIONS

Waste Management:
Do not pour into drains or waterways.

Disposal Methods:
Local, state, provincial, and national disposal regulations may be more or less stringent. Consult your attorney or appropriate
regulatory officials for information on such disposal. This product should not be dumped, spilled, rinsed or washed into sewers
or public waterways.

14 – TRANSPORT INFORMATION

UN Number: 1760
Proper Shipping Name: Corrosive liquid, n.o.s.
IMDG Class: 8
Packing Group: III

15 – REGULATORY INFORMATION

This preparation was classified in compliance with the directive known as <All preparations> 1999/45/EC and its adaptations
In addition directive 2004/73/EC with the 29° adaptation of directive 67/548/EEC (Hazardous substances) have been taken into
account.

Particular hazards associated with the risk and safety recommendations:

R22 Harmful if swallowed
S37 Wear suitable gloves
S60 This material and its container must be disposed of as hazardous waste

Product Label (s):

16 – OTHER INFORMATION

HMIS Rating NFPA 704 Rating

Flammability

HEALTH 1
FLAMMABILITY 0 0
PHYSICAL HAZARD 0
PERSONAL PROTECTION B
Health 1 0 Instability

Specific

HMIS: Hazardous Materials Identification System

NFPA: National Fire Protection Association

Since the user's working conditions are not known by us, the information supplied on this safety data sheet is based on our current level of
knowledge and on national and community regulations.

Revision No.: 00
Revision Date: 01-01-2019 Page 3 of 4
 Product Name: Hydrex 2529
MSDS Code: HYS2529

The product must not be used for any purposes other than those specified under heading 1 without first obtaining written handling
instructions.
It is at all times the responsibility of the user to take all necessary measures to comply with legal requirements and local regulations.
The information given on this safety data sheet must be regarded as a description of the safety requirements relating to our product and not
a guarantee of its properties

Revision No.: 00
Revision Date: 01-01-2019 Page 4 of 4
 Product Name: Hydrex 2856
MSDS Code: HYS2856

MATERIAL SAFETY DATA SHEET

1 – CHEMICAL PRODUCT AND COMPANY IDENTIFICATION

Product Name: Hydrex 2856

Product Application: Corrosion inhibitor

Manufacturer: Veolia Water Solutions & Technologies, Saudi – Chemical Industries

P.O. BOX 58515, Riyadh 11515, Kingdom of Saudi Arabia
Telephone: 011 478 77 21. Fax: 011 478 25 60
www.veoliawaterst.com

Emergency Telephone Number:

Riyadh - KSA 011 478 77 21

2 – COMPOSITION INFORMATION ON INGREDIENTS

Chemical Name CAS No. EC No. %

Sodium Nitrite 7632-00-0 231-555-9 30.0 – 38.0

3 – HAZARDS IDENTIFICATION

Potential Health Effects:

Likely routes of exposure: Eye and skin contact.
Eye contact: Moderately irritating to eyes.
Skin contact: Moderately irritating to skin.
Inhalation: No information available.
Ingestion: Harmful if swallowed

4 – FIRST AID MEASURES

As a general rule, in case of doubt or if symptoms persist, always call a doctor. NEVER induce swallowing in an unconscious
person.
If in eyes: Wash thoroughly with soft, clean water for 15 minutes holding eyelids open. Refer the patient to an
ophthalmologist, in particular if there is any redness, pain or visual impairment.

If on skin: Wash thoroughly with water.

Immediate first aid is not likely to be required. If symptoms occur, remove to fresh air.
If inhaled:
If swallowed: If the quantity is small (no more than one mouthful), rinse the mouth with water and consult a doctor
immediately.

5 – FIRE- FIGHTING MEASURES

Flash Point: Non flammable.

Extinguishing Media: Water spray, foam, dry chemical, or carbon dioxide.
Fire & Explosion Procedures: Move container from fire area if it can be done without risk. Cool containers exposed to
flames with water until well after the fire is out. Keep run-off water out of sewers and
water sources. Dike for water control.

6 – ACCIDENTAL RELEASE MEASURES

Personal Precautions: Use personal protection recommended in section 8.

Environmental Precautions: Keep out of drains and water courses.
Spill Clean up Methods: Contain large spills with dikes and transfer the material to appropriate containers for

Revision No.: 03
Revision Date: 01-01-2016 Page 1 of 4
 Product Name: Hydrex 2856
MSDS Code: HYS2856

reclamation or disposal. Absorb remaining material or small spills with an inert material and
then place in a chemical waste container. Flush spill area with water.

7 – HANDLING AND STORAGE

Handling:
Observe precautions stated on label and also industrial safety regulations. Avoid contact of product with the skin and eyes.
Smoking, eating and drinking are prohibited in premises where the preparation is used.
Emptied containers retain vapour and product residue. Observe all recommended safety precautions until container is cleaned,
reconditioned or destroyed. The reuse of this material's container for non industrial purposes is prohibited and any reuse must
be in consideration of the data provided in this material safety data sheet.

Storage:
Keep the container tightly closed in a dry place.

8 – EXPOSURE CONTROLS/PERSONAL PROTECTION

Protective Equipment:

Eye Protection: Wear safety goggles. Provide eye washes in workshops where the product is constantly handled.
Hand protection: Wear protective gloves.
Body Protection: Although this product does not present a significant skin concern, minimize skin contamination by
following good industrial practice. Wash thoroughly after handling.
Respiratory Protection: Not required.
Ventilation: Provide natural or mechanical ventilation to minimize exposure.

9 – PHYSICAL AND CHEMICAL PROPERTIES

Appearance : Clear
State : Liquid
Color : Deep pink
Odor Characteristic : Not specified
pH of concentrate : 12.8 – 13.2
Specific Gravity @ 25oC : 1.31 – 1.32
Viscosity, cps : Not specified
Melting Point, (Deg. Celsius) : Not specified
Boiling Point, (Deg. Celsius) : Not specified
Percentage Volatility, (%) : Not specified
Solubility in Water : Complete

10 – STABILITY AND REACTIVITY

Stability: Stable
Conditions to avoid: None known
Material to avoid: Acids and flammable materials
Hazardous decomposition products: None known

11 – TOXICOLOGICAL INFORMATION

No data is available regarding the preparation itself.

It is generally agreed that substances contained are likely to cause the appearance of major lesions which persist for at least
twenty-four hours after application to the eye of an animal. And are likely to cause significant irritation which lasts twenty-four
hours after application to the healthy, unbroken skin of an animal for a period of up to 4 hours.

12 – ECOLOGICAL INFORMATION

No ecological data on the product itself is available.

Revision No.: 03
Revision Date: 01-01-2016 Page 2 of 4
 Product Name: Hydrex 2856
MSDS Code: HYS2856

The product must not be allowed to run into drains or waterways.

13 – DISPOSAL CONSIDERATIONS

Waste Management:
Do not pour into drains or waterways.

Disposal Methods:
Local, state, provincial, and national disposal regulations may be more or less stringent. Consult your attorney or appropriate
regulatory officials for information on such disposal. This product should not be dumped, spilled, rinsed or washed into sewers
or public waterways.

14 – TRANSPORT INFORMATION

UN Number: 3098
Proper Shipping Name: Oxidizing substance, liquid, corrosive, n.o.s.
IMDG Class: 5.1
Packing Group: III

15 – REGULATORY INFORMATION

This preparation was classified in compliance with the directive known as <All preparations> 1999/45/EC and its adaptations
In addition directive 2004/73/EC with the 29° adaptation of directive 67/548/EEC (Hazardous substances) have been taken into
account.

Particular hazards associated with the risk and safety recommendations:

R34 Causes burns.
S26 In case of contact with eyes, rinse immediately with plenty of water and seek medical advice
S37 Wear suitable gloves

Product Label (s):

16 – OTHER INFORMATION

HMIS Rating NFPA 704 Rating

Flammability

HEALTH 1
FLAMMABILITY 0 0
PHYSICAL HAZARD 0
PERSONAL PROTECTION B
Health 1 0 Instability

OX

Specific

HMIS: Hazardous Materials Identification System

NFPA: National Fire Protection Association

Since the user's working conditions are not known by us, the information supplied on this safety data sheet is based on our current level of
knowledge and on national and community regulations.

Revision No.: 03
Revision Date: 01-01-2016 Page 3 of 4
 Product Name: Hydrex 2856
MSDS Code: HYS2856

The product must not be used for any purposes other than those specified under heading 1 without first obtaining written handling
instructions.
It is at all times the responsibility of the user to take all necessary measures to comply with legal requirements and local regulations.
The information given on this safety data sheet must be regarded as a description of the safety requirements relating to our product and not
a guarantee of its properties

Revision No.: 03
Revision Date: 01-01-2016 Page 4 of 4
 Product Name: Hydrex 7910
MSDS Code: HYS7910

MATERIAL SAFETY DATA SHEET

1 - CHEMICAL PRODUCT AND COMPANY IDENTIFICATION

Product Name: Hydrex 7910

Product Application: Non-Oxidizing Biocide

Manufacturer: Veolia Water Solutions & Technologies, Saudi - Chemical Industries

P.O. BOX 58515, Riyadh 11515, Kingdom of Saudi Arabia
Telephone: 0147877 21. Fax: 0147825 60
www.veoliawaterst.com

Emergency Telephone Number:

Riyadh- KSA 01 478 77 21

2 - COMPOSITION INFORMATION ON INGREDIENTS

Chemical Name CAS No. EC No. %

5-Chloro-2-methyl-4-isothiazolin-3-one 26172-55-4
2-Methyl-4-isothiazolin-3-one 2682-20-4

3 - HAZARDS IDENTIFICATION

Potential Health Effects:

Likely routes of exposure: Eye, skin contact and inhalation.
Eye contact: Irritant and corrosive to eyes
Skin contact: Irritating to skin
Inhalation: Inhalation of vapour or mist can cause irritation of nose and throat
Ingestion: Material is harmful if swallowed

As a general rule, in case of doubt or if symptoms persist, always call a doctor. NEVER induce swallowing in an unconscious
person.
If in eyes: IMMEDIATELY get under a safety shower. Flush eyes with water for 15 minutes and get medical attention
promptly.

If on skin: IMMEDIATELY get under a safety shower. Flush skin while removing contaminated clothing. Do not take
clothing home to be laundered. Discard contaminated shoes, belts and other articles made of leather. Get
prompt medical attention.
Move subject to fresh air. Give artificial respiration if breathing has stopped.
If inhaled:
If swallowed: If swallowed, give 2 glasses of water to drink. IMMEDIATELY see a physician. Never give anything by
mouth to an unconscious person.

Flash Point: Non flammable.

Extinguishing Media: Water spray, foam, dry chemical, or carbon dioxide.
Fire & Explosion Procedures: Move container from fire area if it can be done without risk. Cool containers exposed to
flames with water until well after the fire is out. Keep run-off water out of sewers and
water sources. Do not breath fumes. Dike for water control.

Revision No.: 02
Revision Date: 24-05-2009 Page 1 of 4
 Product Name: Hydrex 7910
MSDS Code: HYS7910

Personal Precautions: Use personal protection recommended in section 8.

Environmental Precautions: Contain and control the leaks or spills with non-combustible absorbent materials such as
sand, earth, vermiculite, diatom earth in drums for waste disposal.
Prevent any material from entering drains or waterways.
Use drums to dispose of waste recovered in accordance with applicable regulations (see
heading 13).
If the product contaminates waterways, rivers or drains, alert the relevant authorities in
accordance with statutory procedures.
Spill Clean up Methods: Contain large spills with dikes and transfer the material to appropriate containers for
reclamation or disposal. Absorb remaining material or small spills with an inert material and
then place in a chemical waste container. Flush spill area with water.

7 - HANDLING AND STORAGE

Handling:
Observe precautions stated on label and also industrial safety regulations. Avoid contact of product with the skin and eyes.
Smoking, eating and drinking are prohibited in premises where the preparation is used.
Emptied containers retain vapour and product residue. Observe all recommended safety precautions until container is cleaned,
reconditioned or destroyed. The reuse of this material's container for non industrial purposes is prohibited and any reuse must
be in consideration of the data provided in this material safety data sheet.

Storage:
Keep the container tightly closed in a dry place.

8 - EXPOSURE CONTROLS/PERSONAL PROTECTION

Protective Equipment:

Eye Protection: Wear safety googles. Provide eye washes in workshops where the product is constantly handled.
Hand protection: Protective gloves must be worn.
Body Protection: Wear apron while handling/ dosing this product.
Respiratory Protection: Avoid breathing vapour or mist.
Use approved respiratory protection equipment when airborne exposure is excessive. Consult the
respirator manufacturer to determine the appropriate type of equipment for a given application.
The respirator use limitations specified by the manufacturer must be observed.
Ventilation: Provide natural or mechanical ventilation to minimize exposure.
If practical, use local mechanical exhaust ventilation at sources of air contamination such as
processing equipment.

9 - PHYSICAL AND CHEMICAL PROPERTIES

Appearance Clear
State Liquid
Color Pale green
Odor Characteristic Mild
pH of concentrate 3.0-4.0
Specific Gravity @ 25°C 1.005 - 1.025
Viscosity, cps 3 CPS@ 25C/77F
Melting Point, (Deg. Celsius) -3C/27F
Boiling Point, (Deg. Celsius) 100C/212F
Percentage Volatility, (%) 57 to 60%
Solubility in Water Complete

10- STABILITY AND REACTIVITY

Stability: This material is considered stable under specified conditions of storages.

Conditions to avoid: None known
Material to avoid: Avoid contact with oxidizing agents, reducing agents, amines, mercaptans.
Hazardous decomposition products: Thermal decomposition may yield the following: hydrogen chloride, sulphur dioxide,

Revision No.: 02
Revision Date: 24-05-2009 Page 2 of 4
 Product Name: Hydrex 7910
MSDS Code: HYS7910

oxides of nitrogen.

11 - TOXICOLOGICAL INFORMATION

No data is available regarding the preparation itself.

It is generally agreed that substances contained are likely to cause the appearance of major lesions which persist for at least
twenty-four hours after application to the eye of an animal. And are likely to cause significant irritation which lasts twenty-four
hours after application to the healthy, unbroken skin of an animal for a period of up to 4 hours.

12 - ECOLOGICAL INFORMATION

No ecological data on the product itself is available.

The product must not be allowed to run into drains or waterways.

13 - DISPOSAL CONSIDERATIONS

Waste Management:
Do not pour into drains or waterways.

Disposal Methods:
Local, state, provincial, and national disposal regulations may be more or less stringent. Consult your attorney or appropriate
regulatory officials for information on such disposal. This product should not be dumped, spilled, rinsed or washed into sewers
or public waterways.

14 - TRANSPORT INFORMATION

UN Number: 3265
Proper Shipping Name: Corrosive liquid, acidic, organic, n.o.s.
IMDG Class: 8
Packing Group: Ill

15 - REGULATORY INFORMATION

This preparation was classified in compliance with the directive known as <All preparations> 1999/45/EC and its adaptations
In addition directive 2004/73/EC with the 29° adaptation of directive 67/548/EEC (Hazardous substances) have been taken into
account.

Particular hazards associated with the risk and safety recommendations:

R34 Causes burns.
R20/22 Harmful by inhalation and if swallowed.
R34 May cause sensitisation by skin contact.
S36/37/39 Wear suitable protective clothing, gloves and eye/face protection.
S26 In case of contact with eyes, rinse immediately with plenty of water and seek medical advice
S28 After contact with skin, wash immediately with plenty of soap and water.
S45 In case of accident or if you feel unwell, seek medical advice immediately (show the label where possible)
S60 This material and its containers must be disposed of as hazardous waste.

Product Label (s):

Revision No.: 02
Revision Date: 24-05-2009 Page 3 of 4 (( ,,"'1!.C:.',Jl.4=-4='5,' I
HARCO c,"ll, \-9

.,.JI _).WI (J La......, J.J...i.jt,LJ.!u

;;AMHAN Hl';AITAG!c H□TE;l.. F"F>□ Jl';"T
 Product Name: Hydrex 7910
MSDS Code: HYS7910

16- OTHER INFORMATION

HMIS Ratina NFPA 704 Ratina

Flammability

HEALTH 1
FLAMMABILITY 0
PHYSICAL HAZARD 0
Health Instability
PERSONAL PROTECTION B

Specific
HMIS: Hazardous Materials Identification System
NFPA: National Fire Protection Association

Since the user's working conditions are not known by us, the information supplied on this safety data sheet is based on our current level of
knowledge and on national and community regulations.
The product must not be used for any purposes other than those specified under heading 1 without first obtaining written handling
instructions.
It is at all times the responsibility of the user to take all necessary measures to comply with legal requirements and local regulations.
The information given on this safety data sheet must be regarded as a description of the safety requirements relating to our product and not
a guarantee of its properties

Revision No.: 02
Revision Date: 24-05-2009 Page 4 of 4