Specifications

S20D052B0107

Rev.1.00 beta
Revision
Rev.No. Date Comment
th
1.00 beta Mar.4 ,2015 Preliminary version

I
 Cautions
1. To ensure the proper use of this product, please read this document carefully, and keep this file for
future reference.
2. The contents of this document are subject to change without notice. When using the product, please refer to the
latest version of the specifications.
3. Transcription or reduplication of part or this entire document is prohibited without written permission.
4. We are not liable for any damage to the product whatsoever that may be caused by misuse, abuse or any
inadequate environment in which the product is used.
5. To avoid unexpected injury or failure, do not attempt any operation that is not described in the Specifications.
6. Do not attempt disassembling this device unnecessarily. If any sign of disassembling by the user is found, the
product will no longer warranty.
7. We are not responsible for any consequential damages to property, income, or time that result from the use of this
product.
8. We are not warrant or guarantee that the contents of this document do not infringe the industrial property of any
third party.

Safety Cautions
1. Motor:
As part of the motor exposed outside of enclosure, when using this product should install appropriate
protect structure and warning labels should be used, to ensure that users will not directly touch
the motor and cause burns.
In case of motor failure (eg due to CPU runaway, etc.) will cause the motor temperature rise could
cause smoke, fire, if the user inadvertently touches the motor may be injured. Be sure to use a hardware facility
to detect motor failures so it is shut down whenever a failure is detected.

2. Gear:
As part of the gear assembly protrudes from the cutter frame. The designer should design the enclosure so
the user is unable to gain direct access to that part of the gear assembly.

3. Maintenance precautions:
Do not touch the blade.
Do not disassemble the device unless it is absolutely necessary; turn the power off before maintenance.
Connect the auto cutter unit with the correct polarity.

4. Other cautions:
Should prevent any liquid or foreign matter intrusion into the mechanism of this product, because it may
cause smoke, fire, or other serious damage. The structure should be appropriate to protect the user can not
directly touch any sharp edges of this product.

II
 Contents
1. Features ..................................................................................................................................................... 1
2. Specifications ............................................................................................................................................ 1
2.1. General Specifications ................................................................................................................. 1
2.2. Paper Cutting Condition ............................................................................................................. 1
2.3. Switch Specifications ................................................................................................................... 2
2.4. Motor Specifications .................................................................................................................... 2
2.5. Connector Specifications ............................................................................................................. 2
3. Driving method......................................................................................................................................... 3
3.1. Example of driving circuit........................................................................................................... 3
3.2. Motor drive sequence .................................................................................................................. 3
3.3. Drive flow chart............................................................................................................................ 4
3.4. Timing chart ................................................................................................................................. 6
4. Device installation .................................................................................................................................... 7
5. Outline drawing ....................................................................................................................................... 8

III
 Specifications
March 4, 2015

1. Features

• Compact design, easy to install in a variety of printers.

• High reliability and low failure rate.
• Easy to control, low noise.

2. Specifications
2.1. General Specifications

Model S20D052B0107
Cutting method Slide type
Ordinary paper, Thermal paper
Paper width：10mm to 68mm
Cutting paper
Paper thickness：0.06mm to 0.12mm
Paper density：120g/m2 (max.)
Allowable cutting frequency 25 cuts/min.
Life * 1,000,000 cuts (Paper thickness 0.1mm、Normal temperature)
Operating temperature and humidity 0 to 45°C, 5 to 90 % (without condensation)
Outer dimensions 80.40 (W) x 15.40 (D) x 51.96 (H) mm
Weight 125g.

* The life depends on the paper quality, paper width, and paper thickness.

2.2. Paper Cutting Condition

A. Full cut
10 (min.)

1
 Specifications
March 4, 2015

B. Partial Cut

(2)

2.3. Switch Specifications

Rated voltage: DC5.5V

Rated current: 2mA

2.4. Motor Specifications

Motor Terminal Voltage Motor Terminal Voltage

DC 5V ± 10% Approx. 1.9A (5V, 25°C)

2.5. Connector Specifications

A. Pin assignment

Pin No. Wire Color Function

1 Black Motor
2 Red Motor
3 White Switch
4 White Switch

B. Connector Type MOLEX 5264-04

2
 Specifications
March 4, 2015

3. Driving method
3.1. Example of driving circuit

24 V 24 V

12

11

7
A UT O C UT TER

X 1 4 1
IN1 O UT 1
TA 8 4 2 9 H
M
Y 2 8 2
IN2 O UT 2

V CC
6

10 K

SW 4

10 nF

3.2. Motor drive sequence

Forward Reverse Brake Stop

X H L H L
Y L H H L

3
 Specifications
March 4, 2015

3.3. Drive flow chart

Note: When switching the SW from ON to OFF and OFF to ON, implement sensor detection, taking chattering into account.

A. Initialization

Star t

SW = L ? YES

NO

Run the motor

YES

NO SW = L within 700mS ?

YES

Stop the motor

Stop Motor Br ake the motor

ERROR EXIT

4
 Specifications
March 4, 2015

B. Paper Cut

Star t

NO SW = L ?

YES

Run the motor

NO SW = H within 100mS ?

YES

NO SW = L within 700mS ?

YES

Stop the motor

Stop Motor Br ake the motor

ERROR EXIT

5
 Specifications
March 4, 2015

3.4. Timing chart

2ms 150ms (min)

SW

700ms (max)
100ms (max)

6
 Specifications
March 4, 2015

4. Device installation

A. The paper should have no slack in the printer-cutter paper path.

B. To prevent paper jam, insert paper at a right angle to the cutter.
C. To prevent cutting errors due to paper curls, use a paper guide in front of the cutter to keep paper
appressed to the stationary blade.
D. The following shows some examples of cutter layout please refer to the drawings, install the
cutter properly.

PAPER IN
38
30°
10°

A.

PAPER OUT
CUTTER
CUTTER

PAPER OUT

PRINTER

PRINTER
OPEN THE CUTTER

OPEN THE CUTTER

CUTTER

CUTTER

PRINTER PRINTER
7
 Specifications
March 4, 2015

5. Outline drawing