Document ID:

Atlas Copco EngineeredSolutions

ACMS13-235453571-237

Factory acceptance report - dryer

Project Name: Project Number:

Client: Serial number:
Client PO number: Client doc. number:
Equipment description: Client doc. revision:
Model number: Report date:

Table of Content
1 Introduction ................................................................................................................................................................... 2
2 Utilities for factory acceptance test ............................................................................................................................... 2
3 Inspection against drawing ........................................................................................................................................... 2
4 Checks and inspection.................................................................................................................................................. 3
4.1 Check of wiring ...................................................................................................................................................... 3
4.2 Check of alarms settings and PLC program .......................................................................................................... 3
4.3 Check of controls................................................................................................................................................... 3
5 Functional test .............................................................................................................................................................. 4
6 Pressure – leakage test ................................................................................................................................................ 4
7 Visual Inspection........................................................................................................................................................... 5
8 Visual Inspection mechanical ....................................................................................................................................... 5
9 Visual Inspection electrical ........................................................................................................................................... 6
10 Set-up pneumatics ........................................................................................................................................................ 6
11 Function test – measured power/current ...................................................................................................................... 7
12 Function test process times .......................................................................................................................................... 8
13 Function test switching ................................................................................................................................................. 9
14 Function test temperatures ........................................................................................................................................... 9
15 Function test pressure/flow ......................................................................................................................................... 10
16 Set-points ................................................................................................................................................................... 11
17 Set-points dew point analyzer ..................................................................................................................................... 11
18 Set-points thermostats ................................................................................................................................................ 12
19 Local control panel or junction box ............................................................................................................................. 12
20 Programmable logic controller (PLC) .......................................................................................................................... 13
21 Communication ........................................................................................................................................................... 13
22 Comments .................................................................................................................................................................. 14
23 Appendix I - checklists ................................................................................................................................................ 15
23.1 Actuated valves ................................................................................................................................................... 15
23.2 Hand valves......................................................................................................................................................... 16
23.3 Indicators ............................................................................................................................................................. 17
23.4 Alarms and controls............................................................................................................................................. 18
24 Appendix II – factory acceptance test certificate ......................................................................................................... 19

© Atlas Copco | Confidentiality class external. Uncontrolled when printed 2024-04-25 09:42
1(19) Revision: 6
 Document ID:
Atlas Copco EngineeredSolutions
ACMS13-235453571-237

Factory acceptance report - dryer

Project Name: Project Number:

Client: Serial number:
Client PO number: Client doc. number:
Equipment description: Client doc. revision:
Model number: Report date:

1 Introduction
This document forms part of the process of the Factory Acceptance Test (FAT) of an Adsorption Dryer unit.
For details please refer to the function test procedure in the IMS (Function test instruction)
Inspections will be carried out against the latest revision of the relevant documents and drawings with as a minimum
Process and Instrumentation Diagram (P&ID), Electrical Wiring Diagram and General Arrangement Drawing (GA)
All checked and accepted items shall be marked on the drawing with green (“highlight marker”).
If a section is not applicable to the product being tested, tick the “Not applicable” check point in the appropriate
section.
All deviations from the drawing or testing shall be indicated on the drawing with Red, Blue or orange;
 Red for wrong information (info to be deleted)
 Orange for items not present during test, thus not tested.
 Blue for correct information (info to be added)
Remarks shall be written in clouds on the drawing
All accepted deviations shall be updated on the “AS BUILT” drawing.

2 Utilities for factory acceptance test

The following utilities are needed during FAT
 Compressed air 6 Bar for pilot air supply
 Power supply: follow wiring diagram
 Portable dew point Analyser Blank template

3 Inspection against drawing

Checking of all items will be done before the commencement of the test according the following documents (latest
revisions):

Name Document number Revision

Process and Instrumentation diagram

General arrangement drawing
Wiring diagram local control panel
☐ Not applicable Control Description

☐ Not applicable Cause and effect chart

☐ Not applicable Inspection and test plan

☐ Not applicable Logic diagram

☐ Not applicable Loop diagram

Accepted deviations shall be updated on the “As Built” drawings.

© Atlas Copco | Confidentiality class external. Uncontrolled when printed 2024-04-25 09:42
2(19) Revision: 6
 Document ID:
Atlas Copco EngineeredSolutions
ACMS13-235453571-237

Factory acceptance report - dryer

Project Name: Project Number:

Client: Serial number:
Client PO number: Client doc. number:
Equipment description: Client doc. revision:
Model number: Report date:

4 Checks and inspection

4.1 Check of wiring

All electrical connections and loops will be checked against the latest revision of the Electrical drawings, mentioned
in chapter 3 of this procedure and be confirmed as checked and approved in chapter 19.

4.2 Check of alarms settings and PLC program

Checking of alarms and settings will be performed.
Appendix I will be completed.
A laptop will be used to read PLC values and check controls.
Deviations will be listed in Appendix II.
If necessary, changes shall be made in the PLC software to correct faulty outputs.
Any changes will be agreed with Company representative as (if) required.

4.3 Check of controls

a) All actuated valves will be tested on proper operation by:
 Checking them while the unit runs its cycles
b) All hand valves will be tested on proper operation by:
 Manually opening and closing of the valves
c) Analogue instruments
 Analogue instruments will be tested by simulation (if simulation is applicable) during the FAT, displayed
values shall be in line with expected values.
d) All transmitters will be tested on proper operation by:
 Check reading after power on.
o Check of scale & ranges
e) Dew point analyser will be tested on proper operation by:
 Check reading after power on.
o Check of scale & ranges

© Atlas Copco | Confidentiality class external. Uncontrolled when printed 2024-04-25 09:42
3(19) Revision: 6
 Document ID:
Atlas Copco EngineeredSolutions
ACMS13-235453571-237

Factory acceptance report - dryer

Project Name: Project Number:

Client: Serial number:
Client PO number: Client doc. number:
Equipment description: Client doc. revision:
Model number: Report date:

5 Functional test
After all set points and alarms are tested, a complete functional test of the Adsorption Dryer Package will be performed
as per this document.
The alarms and controls will be tested and documented according appendix I.
Test certificate will be filled-in and signed by Atlas Copco and customer’s inspection representative according appendix II.
Deviations / punch list item, if applicable, will be documented in the project punch list.

6 Pressure – leakage test

All pressure measures shall be read on a calibrated pressure gauge.
When the Dryer is finally assembled and safety equipment is installed, the Dryer must be pressure tested, inlet valves
shall be manually forced to open position and test flanges must be installed.
Test A and B will always be applicable unless soap water is not allowed then Test B will be applicable.
A Leak test 0.5 Bar.
Pressure is built up to 0.5 Bar and soap water is spayed on all assemblies to prove tightness
Tightness is signed with OK.
B Leak test 7 Bar.
Pressure must be built up to 8 Bar.
Spray soap water on all assemblies and tightness must be proved after 30 minutes.
Pressure must be read and noted after 30 minutes and signed with OK.
C Alternatively pressure must be held for 8 Hours if soap water is not allowed to use.
Pressure must be read and noted after 8 Hours and signed with OK.
After all set points and alarms are tested, a complete functional test of the Adsorption Dryer Package will be performed
as per this document.

Results

Test done by: Date:

A Bar ☐ OK Remark:

B Bar ☐ 30 minutes OK Remark:

C Bar ☐ 8 hours OK Remark:

Reason(s) for non-approval:

© Atlas Copco | Confidentiality class external. Uncontrolled when printed 2024-04-25 09:42
4(19) Revision: 6
 Document ID:
Atlas Copco EngineeredSolutions
ACMS13-235453571-237

Factory acceptance report - dryer

Project Name: Project Number:

Client: Serial number:
Client PO number: Client doc. number:
Equipment description: Client doc. revision:
Model number: Report date:

7 Visual Inspection

Results ☐ Section not applicable ☐ Accepted ☐ Not Accepted

Test done by: Date:

Construction mechanical 100% ☐ Accepted
Construction instrumentation 100% ☐ Accepted
Construction electrical 100% ☐ Accepted
Tag numbers 100% ☐ Accepted ☐ Not applicable
Reason(s) for non-approval:

8 Visual Inspection mechanical

Results ☐ Section not applicable ☐ Accepted ☐ Not Accepted

Test done by: Date:

Batch instrument serial number list 100% ☐ Accepted ☐ Not applicable
Piping/valves supports 100% ☐ Accepted
Instrumentation 100% ☐ Accepted
Filters 100% ☐ Accepted ☐ Not applicable
Valves 100% ☐ Accepted
Actuators 100% ☐ Accepted ☐ Not applicable
Limit switch boxes 100% ☐ Accepted ☐ Not applicable
Instrumentation connections 100% ☐ Accepted
Base frame 100% ☐ Accepted
Painting 100% ☐ Accepted
Reason(s) for non-approval:

© Atlas Copco | Confidentiality class external. Uncontrolled when printed 2024-04-25 09:42
5(19) Revision: 6
 Document ID:
Atlas Copco EngineeredSolutions
ACMS13-235453571-237

Factory acceptance report - dryer

Project Name: Project Number:

Client: Serial number:
Client PO number: Client doc. number:
Equipment description: Client doc. revision:
Model number: Report date:

9 Visual Inspection electrical

Results ☐ Section not applicable ☐ Accepted ☐ Not Accepted

Test done by: Date:

Cable 100% ☐ Accepted
Cable glands (make and mounting) 100% ☐ Accepted
Shrouds 100% ☐ Accepted
Cable trays 100% ☐ Accepted ☐ Not applicable
Cable ty-raps 100% ☐ Accepted ☐ Not applicable
Cable pig tails 100% ☐ Accepted ☐ Not applicable
Earth continuity test ☐ Accepted ☐ Not applicable
Minimum: Ohm Maximum: Ohm
Dielectric withstand test ☐ Accepted ☐ Not applicable
Voltage mA Seconds
Reason(s) for non-approval:

10 Set-up pneumatics

Results ☐ Section not applicable ☐ Accepted ☐ Not Accepted

Test done by: Date:

Solenoids 100% ☐ Accepted
Pilot Air Tubing 100% ☐ Accepted
Pilot Air tubing supports 100% ☐ Accepted
Filter Reducer Instrument Air ☐ Not applicable ☐ Accepted Set @ Bar
Filter Reducer Control valve ☐ Not applicable ☐ Accepted Set @ Bar
Safety valve Instrument Air ☐ Not applicable ☐ Accepted Set @ Bar
Reason(s) for non-approval:

© Atlas Copco | Confidentiality class external. Uncontrolled when printed 2024-04-25 09:42
6(19) Revision: 6
 Document ID:
Atlas Copco EngineeredSolutions
ACMS13-235453571-237

Factory acceptance report - dryer

Project Name: Project Number:

Client: Serial number:
Client PO number: Client doc. number:
Equipment description: Client doc. revision:
Model number: Report date:

11 Function test – measured power/current

Results ☐ Section not applicable ☐ Accepted ☐ Not Accepted

Test done by: Date:

L1-L2 V L2-L3 V L1-L3 V
Main Supply
L1-N V
Control supply DC V AC V Other V
Heater total power kW ☐ Not applicable
Power group 1 kW ☐ Not applicable
Power group 2 kW ☐ Not applicable
Power group 3 kW ☐ Not applicable
Power group 4 kW ☐ Not applicable
Power group 5 kW ☐ Not applicable
Current group 1 U-V Amp. V-W Amp. U-W Amp.
Current group 2 U-V Amp. V-W Amp. U-W Amp.
Current group 3 U-V Amp. V-W Amp. U-W Amp.
Current group 4 U-V Amp. V-W Amp. U-W Amp.
Current group 5 U-V Amp. V-W Amp. U-W Amp.
Blower U-V Amp. V-W Amp. U-W Amp.
Reason(s) for non-approval:

© Atlas Copco | Confidentiality class external. Uncontrolled when printed 2024-04-25 09:42
7(19) Revision: 6
 Document ID:
Atlas Copco EngineeredSolutions
ACMS13-235453571-237

Factory acceptance report - dryer

Project Name: Project Number:

Client: Serial number:
Client PO number: Client doc. number:
Equipment description: Client doc. revision:
Model number: Report date:

12 Function test process times

Results ☐ Section not applicable ☐ Accepted ☐ Not Accepted

Test done by: Date:

Parallel Drying (split flow) seconds ☐ Not applicable
Maximal Drying time (half cycle) Minutes
De-pressurising Seconds
Minimal Heating Minutes ☐ Not applicable
Maximal Heating Minutes ☐ Not applicable
Minimal Cooling Minutes ☐ Not applicable
Maximal Cooling Minutes ☐ Not applicable
Purge / Heating Seconds ☐ Not applicable
Purge Cooling Seconds ☐ Not applicable
Purging Seconds ☐ Not applicable
Pressurising Seconds
Maximal Stand-by Minutes ☐ Not applicable
Reason(s) for non-approval:

© Atlas Copco | Confidentiality class external. Uncontrolled when printed 2024-04-25 09:42
8(19) Revision: 6
 Document ID:
Atlas Copco EngineeredSolutions
ACMS13-235453571-237

Factory acceptance report - dryer

Project Name: Project Number:

Client: Serial number:
Client PO number: Client doc. number:
Equipment description: Client doc. revision:
Model number: Report date:

13 Function test switching

Results ☐ Section not applicable ☐ Accepted ☐ Not Accepted

Test done by: Date:

Drains ☐ Accepted ☐ Not applicable
Pressurize Valves ☐ Accepted ☐ Not applicable
De-Pressurize Valves ☐ Accepted ☐ Not applicable
Inlet Valves ☐ Accepted
Outlet Valves ☐ Accepted
Process Valves ☐ Accepted ☐ Not applicable
Pressure Control Valves ☐ Accepted ☐ Not applicable
Heater on/off ☐ Accepted ☐ Not applicable
Frequency converter ☐ Accepted ☐ Not applicable
Blower flow switch ☐ Accepted ☐ Not applicable
Reason(s) for non-approval:

14 Function test temperatures

Results ☐ Section not applicable ☐ Accepted ☐ Not Accepted

Test done by: Date:

Blower inlet °C ☐ Not applicable
Heater inlet °C ☐ Not applicable
Heater outlet °C ☐ Not applicable
End of Heating phase °C ☐ Not applicable
End of Cooling phase °C ☐ Not applicable
Dryer inlet °C ☐ Not applicable
Dryer outlet °C ☐ Not applicable
Reason(s) for non-approval:

© Atlas Copco | Confidentiality class external. Uncontrolled when printed 2024-04-25 09:42
9(19) Revision: 6
 Document ID:
Atlas Copco EngineeredSolutions
ACMS13-235453571-237

Factory acceptance report - dryer

Project Name: Project Number:

Client: Serial number:
Client PO number: Client doc. number:
Equipment description: Client doc. revision:
Model number: Report date:

15 Function test pressure/flow

Results ☐ Section not applicable ☐ Accepted ☐ Not Accepted

Test done by: Date:

Air Inlet Pressure bar ☐ Not applicable
Air Outlet Pressure Bar ☐ Not applicable
Pressure Difference Pre-Filter(s) mBar ☐ Not applicable
Pressure Difference After Filter(s) mBar ☐ Not applicable
Purge Flow m³/Hr. ☐ Not applicable
Control Valve Offset % ☐ Not applicable
Blower Pressure during heating mBar ☐ Not applicable
Blower Frequency during heating Hz ☐ Not applicable
Blower Pressure during cooling mBar ☐ Not applicable
Blower Frequency during cooling Hz ☐ Not applicable
Reason(s) for non-approval:

© Atlas Copco | Confidentiality class external. Uncontrolled when printed 2024-04-25 09:42
10(19) Revision: 6
 Document ID:
Atlas Copco EngineeredSolutions
ACMS13-235453571-237

Factory acceptance report - dryer

Project Name: Project Number:

Client: Serial number:
Client PO number: Client doc. number:
Equipment description: Client doc. revision:
Model number: Report date:

16 Set-points

Results ☐ Section not applicable ☐ Accepted ☐ Not Accepted

Test done by: Date:

Pressure Differential Transmitter Pre-filter(s) ☐ Not applicable High mBar

Pressure Differential Transmitter After-Filter(s) ☐ Not applicable High mBar

Minimal working pressure ☐ Not applicable Low Bar

Maximal working pressure adsorber A ☐ Not applicable High Bar

High regeneration pressure adsorber A ☐ Not applicable High Bar

Maximal working pressure adsorber B ☐ Not applicable High Bar

High Regeneration pressure adsorber B ☐ Not applicable High Bar

Maximum differential pressure adsorbers ☐ Not applicable High Bar

High Dryer inlet Temperature ☐ Not applicable High °C

Low Dryer inlet Temperature ☐ Not applicable Low °C

Dew point changeover ☐ Not applicable Set-point °C

Dew point too high ☐ Not applicable High °C

Blower Thermal Overload Protection ☐ Not applicable Set-point Amp.

Reason(s) for non-approval:

17 Set-points dew point analyzer

Results ☐ Section not applicable ☐ Accepted ☐ Not Accepted

Test done by: Date:

Set point high alarm ☐ Not applicable °C Set-point alarm B ☐ Not applicable °C

Range high ☐ Not applicable °C Range low ☐ Not applicable °C

Set point analyzer fault ☐ Not applicable °C

Flow sensor ☐ Not applicable L/m

Reason(s) for non-approval:

© Atlas Copco | Confidentiality class external. Uncontrolled when printed 2024-04-25 09:42
11(19) Revision: 6
 Document ID:
Atlas Copco EngineeredSolutions
ACMS13-235453571-237

Factory acceptance report - dryer

Project Name: Project Number:

Client: Serial number:
Client PO number: Client doc. number:
Equipment description: Client doc. revision:
Model number: Report date:

18 Set-points thermostats

Results ☐ Section not applicable ☐ Accepted ☐ Not Accepted

Test done by: Date:

Reading (scale) Heater high temperature alarm ☐ Not applicable °C
Panel temperature heater ☐ Not applicable °C
Panel temperature cooler ☐ Not applicable °C
Reason(s) for non-approval:

19 Local control panel or junction box

Results ☐ Section not applicable ☐ Accepted ☐ Not Accepted

Test done by: Date:

Visual Check Hardware ☐ Accepted
Visual Check Wiring general (termination, pins etc.) ☐ Accepted
Visual Check Wiring Diagram present ☐ Accepted
Visual Check HMI cover ☐ Accepted ☐ Not applicable
Visual Check Vortex Cooler ☐ Accepted ☐ Not applicable
Visual Check Doorstop ☐ Accepted ☐ Not applicable
Visual Check Wiring (make, colour, size) ☐ Accepted ☐ Not applicable
Visual Check sleeve markers ☐ Accepted ☐ Not applicable
I/O Loop test Limit Switches ☐ Accepted ☐ Not applicable
I/O Loop test Solenoids ☐ Accepted ☐ Not applicable
I/O Loop test Analogue Instruments ☐ Accepted ☐ Not applicable
Main Switch ☐ Accepted ☐ Not applicable
Fuses / Circuit Breakers ☐ Accepted ☐ Not applicable
Relays ☐ Accepted ☐ Not applicable
Reason(s) for non-approval:

© Atlas Copco | Confidentiality class external. Uncontrolled when printed 2024-04-25 09:42
12(19) Revision: 6
 Document ID:
Atlas Copco EngineeredSolutions
ACMS13-235453571-237

Factory acceptance report - dryer

Project Name: Project Number:

Client: Serial number:
Client PO number: Client doc. number:
Equipment description: Client doc. revision:
Model number: Report date:

20 Programmable logic controller (PLC)

Results ☐ Section not applicable ☐ Accepted ☐ Not Accepted

Test done by: Date:

Visual Check Hardware ☐ Accepted ☐ Not applicable
Visual Check Wiring ☐ Accepted ☐ Not applicable
Visual Check Memory Card present ☐ Accepted ☐ Not applicable
PLC (CPU) in Run mode ☐ Accepted ☐ Not applicable
I/O Points Module Cards (connections) ☐ Accepted ☐ Not applicable
HMI read-out ☐ Accepted ☐ Not applicable
HMI password 1 ☐ Not applicable
HMI password 2 ☐ Not applicable
Software version installed Date installed:
Reason(s) for non-approval:

21 Communication

Results ☐ Section not applicable ☐ Accepted ☐ Not Accepted

Test done by: Date:

Modbus serial RS485 Slave
Address 1 Address 2 Mode
Baudrate Databits Stopbit Parity Port
☐ Not applicable
☐ Not applicable Ethernet – TCP/IP
Network address PLC
Network address HMI
☐ Not applicable Fiber optic
Network address PLC
Network address HMI
Reason(s) for non-approval:

© Atlas Copco | Confidentiality class external. Uncontrolled when printed 2024-04-25 09:42
13(19) Revision: 6
 Document ID:
Atlas Copco EngineeredSolutions
ACMS13-235453571-237

Factory acceptance report - dryer

Project Name: Project Number:

Client: Serial number:
Client PO number: Client doc. number:
Equipment description: Client doc. revision:
Model number: Report date:

22 Comments

No. Comment

© Atlas Copco | Confidentiality class external. Uncontrolled when printed 2024-04-25 09:42
14(19) Revision: 6
 Document ID:
Atlas Copco EngineeredSolutions
ACMS13-235453571-237

Factory acceptance report - dryer

Project Name: Project Number:

Client: Serial number:
Client PO number: Client doc. number:
Equipment description: Client doc. revision:
Model number: Report date:

23 Appendix I - checklists

23.1 Actuated valves

Actuated valve (tag number) Checked Corrective action by Checked Approved

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

© Atlas Copco | Confidentiality class external. Uncontrolled when printed 2024-04-25 09:42
15(19) Revision: 6
 Document ID:
Atlas Copco EngineeredSolutions
ACMS13-235453571-237

Factory acceptance report - dryer

Project Name: Project Number:

Client: Serial number:
Client PO number: Client doc. number:
Equipment description: Client doc. revision:
Model number: Report date:

23.2 Hand valves

Hand valve (tag number) Checked Corrective action by Checked Approved

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

© Atlas Copco | Confidentiality class external. Uncontrolled when printed 2024-04-25 09:42
16(19) Revision: 6
 Document ID:
Atlas Copco EngineeredSolutions
ACMS13-235453571-237

Factory acceptance report - dryer

Project Name: Project Number:

Client: Serial number:
Client PO number: Client doc. number:
Equipment description: Client doc. revision:
Model number: Report date:

23.3 Indicators

Indicator (tag number) Checked Corrective action by Checked Approved

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

© Atlas Copco | Confidentiality class external. Uncontrolled when printed 2024-04-25 09:42
17(19) Revision: 6
 Document ID:
Atlas Copco EngineeredSolutions
ACMS13-235453571-237

Factory acceptance report - dryer

Project Name: Project Number:

Client: Serial number:
Client PO number: Client doc. number:
Equipment description: Client doc. revision:
Model number: Report date:

23.4 Alarms and controls

Alarms and Controls (tag number) Checked Corrective action by Checked Approved

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

☐ Yes ☐ Not applicable ☐ ☐ Yes

© Atlas Copco | Confidentiality class external. Uncontrolled when printed 2024-04-25 09:42
18(19) Revision: 6
 Document ID:
Atlas Copco EngineeredSolutions
ACMS13-235453571-237

Factory acceptance report - dryer

Project Name: Project Number:

Client: Serial number:
Client PO number: Client doc. number:
Equipment description: Client doc. revision:
Model number: Report date:

24 Appendix II – factory acceptance test certificate

This is to certify all activities mentioned below are executed according to this FAT procedure. Results of tests and
checks are noted in the various certificates.
Any remedial work arising during FAT shall be completed before shipment

FAT Activity Date Name Signature Remark

Inspection against drawing

Check of Wiring

Check of alarms, settings & PLC

Programs

Check of Controls

Functional and performance test

Name Date Company Signature

© Atlas Copco | Confidentiality class external. Uncontrolled when printed 2024-04-25 09:42
19(19) Revision: 6