Marmoxan Tds 2024

TECH
NICAL BULLETIN
Performance Properties -
Marmoxan®
American Standard
Physical properties
SN-101-2020
PROPERTIES TYPICAL RESULTS TEST PROCEDURE
Tensile strength 6,000 psi ASTM D 638
Tensile modulus 600,000 psi ASTM D 638

Flexural strength 10,000 psi ASTM D 790
Flexural modulus 1,000,000 psi ASTM D 790
Shrinkage Test 0.50% ASTM D 638
65 Barcol ASTM D 2583

Hardness
Thermal expansion 56 x 10-6 1/K DIN 53752
Compression strength 238 N/mm2 ASTM D695
Light Fastness Better than 7 DIN 53389
Stain resistance Pass Rating 41 ANSI Z 124
Abrasion resistance Pass ASTM D4060

Boiling water absorption 0.0166 DIN 53495
High temperature resistance Grade 4 (slight change on gloss level) DIN EN 438.point 8
Resistance to cigarette burns Grade 3 DIN EN 438 Point 18
Impact strength
>22 no damage DIN EN 438 point 11
Fungi and Bacterial resistance Not support bacterial growth ASTM G 21, G22
Specific gravity
Solid colors 1.75 ASTM D 792
Patterned colors 1.7
0.006 %
Water absorption DIN 53495
Fire behavior B1 DIN 4102/1

Flame spread 10 ASTM E 84
Smoke density 10 ASTM E 84
Hygiene behavior Suitable Microbiological hygiene test

Physiologically suitable 31 of the German food
Suitable for food contact application
standards and
consumer regulations
https://www.cmbegypt.com/
16
Chemical Resistance performance

1. Test method
- Apply 3 drops of each chemical reagent on the surface of Marmoxan® Solid Surfaces
- Expose the sample for 16 hours; covered with glass plate and uncovered
- Check the surface and scrub the surface with a wet Scotch-Brite® Pad and bleaching cleanser such as Ajax®
2. Test result
The residue from the following chemical reagents can be removed with a wet Scotch-Brite® pad and bleaching cleanser.
- Acetic acid (10%) - Acetone

- Ammonia - Ammonium hydroxide (5,28%)
- Amyl acetate - Amyl alcohol
- Ball point pen - Benzene
- Bleach (household type) - Blood
- B-4 body conditioner - Butyl alcohol
- Carbon disulfide - Carbon tetrachloride
- Citric acid (10%) - Calcium thiocyanate (78%)
- Cigarette (nicotine and tar) - Coffee
- Cooking oils - Cottonseed oil
- Crystal Violet (Biochemical colorants) - Dishwashing liquid/powders
- Cupra ammonia - Ethyl acetate
- Ethanol - Formaldehde
- Ethyl ether - Gentian violet
- Gasoline - Hair dyes
- Grape juice - Hydrochloric acid (20,30,37%)
- Household soaps - Iodine (1%)
- Hydrogen peroxide - Lemon juice
- Ketchup - Mercurochrome (2%)
- Lipstick - Methylene Blue (Biochemical colorants)
- Methanol - Methyl ethyl ketone
- Methyl orange (1%) - Methyl red (1%)
- Mineral oil - Mustard
- Nail polish - Naphthalene
- N-hexane - Olive oil
- Pencil lead - Perchloric acid
- Permanent marker pen - Povidon-iodine(PVP-I) “Betadine” solution
- Potassium hydroxide solution (5, 10, 25, 40%) - Shoe polish
- Soapless detergents - Sodium bisulfate
- Sodium hydroxide solution (5,10,25,40%) - Soy sauce
- Sodium sulfate - Sulfuric acid (25,33,60%)
- Sugar (sucrose) - Tea
- Tetrahydrofuran - Toluene
- Tomato juice - Urea (6%)
- Uric acid - Vinegar
- Washable inks - Wine
- Xylene - Zinc Chloride
16
Note: Biochemical colorants is a dyeing material. It may leave stain on Marmoxan® instantly.
When Marmoxan® is exposure to biochemical colorant, please remove it within a few minutes with acetone.
STORAGE:
Marmoxan® must be stored flat and fully supported with no sagging or bowing. The pallets that Marmoxan® is shipped on are ideal for
storing as long as they remain in good condition and can maintain a flat level surface. It is imperative that the panels remain as flat as
possible in order to avoid damage. Marmoxan® must be stored in a dry and well-ventilated area between 15°-30°C.
BEFORE INSTALLATION: Check for damage that may have occurred in transit. Store materials in an environmentally controlled ar ea, 24
hours before installation. Confirm that the sizes, styles/models, and colors match your order. Check all specifications to ensure that you
have the right material for the job. To ensure that seams line up and are as inconspicuous as possible, ensure that the substrate and sub-
wall are flat, plumb, and square. When installing wall cladding ensure back of panel is no more than 1.5mm from wall substrate.
RECOMMENDED TOOLS:
Belt sander, circular saw with fine tooth carbide blades, router (1-3/4” HP, 22,000 rpm), random orbital sander, electric drill with carbide or
high speed steel bits, tape measure, grease pencil, clamps, denatured alcohol, safety goggles, white paper towels, caulking gun, dust
masks, masking tape, level/straight edge, If needed: 3” clear packaging tape, scotch brite pads, 50ml hard seam adhesive disp enser or
any equipment do the job, extra hard seam mixing tips
USING TOOLS:
Sawing: Cut only on finished side (front) and use wide masking tape to protect finished surfaces from scratching or chipping.
Drilling: Drill from finished side (front) of material.
Sanding: Using recommended sanding paper (open coat or semi open -silicon-carbide or Aluminum oxide)
Always saw, drill, or sand with the material fully supported. See Figure 1. on the following page. The shipping pallet is an ideal work
surface.
ADHESIVES AND SEALANTS: Acrylic adhesive 2 component (Marmoxan Glue) -Translucent 100% Silicone Color Matched Silicone

Marmoxan Tds 2024

Uploaded by

Copyright:

Available Formats

Marmoxan Tds 2024

Uploaded by

Document Information

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Marmoxan Tds 2024

Uploaded by

Copyright:

Available Formats

TECH

Tensile strength 6,000 psi ASTM D 638

Tensile modulus 600,000 psi ASTM D 638

Flexural modulus 1,000,000 psi ASTM D 790

Shrinkage Test 0.50% ASTM D 638

65 Barcol ASTM D 2583

Stain resistance Pass Rating 41 ANSI Z 124

Abrasion resistance Pass ASTM D4060

Fire behavior B1 DIN 4102/1

Hygiene behavior Suitable Microbiological hygiene test

Chemical Resistance performance

- Acetic acid (10%) - Acetone

You might also like