Ba S

BA-S
TECHNICAL DATA SHEET
Basis
Aramide fibres, NBR
General properties and application
Gasket material with good chemical and mechanical properties, resistance to oil, fuels and cooling
liquids. It is used in automotive industry.
Approvals
CRS, UDT
Dimensions of standard sheets
Sheet size: 1000 x 1500 mm, 1500 x 1500 mm
Thickness: 0.5 mm, 0.8 mm, 1.0 mm, 1.5 mm, 2.0 mm, 3.0 mm (other thicknesses on request)
Tolerances: Thickness: < 1 mm ± 0.1 mm, ≥ 1 mm ± 10 %, Length: ± 50 mm, Width: ± 50
Surface treatment: Treatment with graphite, PTFE and antistick coating is available on request.
Technical data
Typical values (thickness 2.0 mm)
Compressibility ASTM F 36/J 8%
Recovery ASTM F 36/J 50 %
Tensile strenght DIN 52910 11 MPa
Stress resistance DIN 52913
• 16h, 300°C, 50 MPa 20 MPa
• 16h, 175°C, 50 MPa 28 MPa
Specific Leak rate DIN 3535/6 0.05 mg/(s.m)
Thickness increase ASTM F 146
• Oil IRM 903, 5h, 150°C 5%
• ASTM Fuel B, 5h, 23°C 5%
*Max. operating conditions
Peak temperature 330°C / 626°F
Continuous temperature 250°C / 482°F
- with steam 200°C / 392°F
Pressure 100 bar / 1450 psi
* Temperature and pressure represent maximum values and should not be used simultaneously. They are given only for
guidance, since they depend not only on the type of gasket material but also on the assembly conditions. Very
important factors are: thickness of material, nature of service medium, type of flange, surface stress. Steam application
requires special consideration.
BA-S, 2 mm
EN 1514-1, Type IBC, PN 40/DIN 28091-2, 3.8
150
General suitability using common installation
[bar]
practices under the condition of chemical

compatibility.
100
Max. performance is ensure through
P R E S S U R E
appropriate measures for joint design and

gasket installation. Consultation is
50
recommended.
Limited application area - Technical
consultation is mandatory. 0
0 50 100 150 200 250 300
T E M P E R A T U R E [°C]
This edition cancels all previous issues. Subject to change without notice.
BA-S
The recommendations made here are intended to be a guideline
for the selection of the suitable gasket quality Because the function
and durability of the products depend upon a number of factors,
the data may not be used to support any warranty claims
Recommended
Recommendation depends on operating conditions
Not recommended
Acetamide Ethyl acetate Oleum

Acetic acid 10% Ethyl alcohol Oxalic acid
Acetic acid 100% Ethyl chloride Oxygen
Acetic ester Ethylene Palmitic acid
Acetone Ethylene glycol Pentane
Acetylene Formic acid 10% Perchloroethylene
Adipic acid Formic acid 85% Phenol
Air Formaldehyde Phosphoric acid
Alum Freon 12 Potassium acetate
Aluminium acetate Freon 22 Potassium bicarbonate
Aluminium chlorate Fuel oil Potassium carbonate
Aluminium chloride Gasoline Potassium chloride
Ammonia Glycerine Potassium dichromate
Ammonium bicarbonate Heptane Potassium hydroxide
Ammonium chloride Hydraulic oil (Mineral) Potassium iodide
Ammonium hydroxide Hydraulic oil (phosphate esther type) Potassium nitrate
Amyl acetate Hydraulic oil (glycol based) Potassium permanganate
Aniline Hydrazine Propane
Asphalt Hydrochloric acid 20% Pyridine
Barium chloride Hydrochloric acid 36% Salicylic acid
Benzene Hydrofluoric acid 10% Silicone oil
Benzoic acid Hydrofluoric acid 40% Soap
Boric acid Hydrogen Sodium aluminate
Borax Isobutane Sodium bicarbonate
Butane Isooctane Sodium bisulphite
Butyl alcohol Isopropyl alcohol Sodium carbonate
Butyric acid Kerosene Sodium chloride
Calcium chloride Lead acetate Sodium cyanide
Calcium hydroxide Lead arsenate Sodium hydroxide
Carbon disulphide Magnesium sulphate Sodium sulphate
Carbon dioxide Malic acid Sodium sulphide
Chloroform Methane Starch
Chlorine, dry Methanol Steam
Chlorine, wet Methyl chloride Stearic acid
Chromic acid Methylene dichloride Sugar
Citric acid Methyl ethyl ketone Sulphuric acid 20%
Copper acetate Milk Sulphuric acid 96%
Creosote Mineral oil type ASTM no.1 Tar
Cresol Naphtha Tartaric acid
Cyclohexanol Nitric acid 20% Toluene
Cyclohexanone Nitric acid 40% Transformer oil
Decaline Nitric acid 96% Trichlorethylene
21-3-2003
Dibenzyl ether Nitrobenzene Water

Dimethyl formamide Nitrogen White Spirit
Dowtherm Octane Xylene
Ethane Oleic acid
In order to spread the most comprehensive knowledge of

our products, our highly skilled group of experts organized DONIT TESNIT d.d.
Cesta komandanta Staneta 38
in the technical-service department can assist you by solving 1215 MEDVODE, Slovenija
telefon: +386 (01) 582 32 00
practically any sealing problem. If you need our help, fax: +386 (01) 582 32 06, 582 32 08
E - m a i l : i n f o @d o n i t t e s n i t . s i
contact us. http://www.donittesnit.si

Ba S

Uploaded by

Copyright:

Available Formats

Ba S

Uploaded by

Document Information

Original Description:

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Ba S

Uploaded by

Copyright:

Available Formats

BA-S

TECHNICAL DATA SHEET

practices under the condition of chemical

appropriate measures for joint design and

Acetamide Ethyl acetate Oleum

Dibenzyl ether Nitrobenzene Water

In order to spread the most comprehensive knowledge of

You might also like