Multiprotocol Label Switching

Multiprotocol Label Switching
(MPLS)
Multiprotocol Label Switching (MPLS) is a protocol-agnostic routing
technique designed to speed up and shape traffic flows across
enterprise wide area and service provider networks.
MPLS allows most data packets to be forwarded at Layer 2 -- the switching

level -- of the Open Systems Interconnection (OSI) model, rather than
having to be passed up to Layer 3 -- the routing level. For this reason, it is
often informally described as operating at Layer 2.5.
MPLS was created in the late 1990s as a more efficient alternative to

traditional Internet Protocol (IP) routing, which requires each router to
independently determine a packet's next hop by inspecting the packet's
destination IP address before consulting its own routing table. This process
consumes time and hardware resources, potentially resulting in degraded
performance for real-time applications, such as voice and video.
In an MPLS network, the first router to receive a packet determines the

packet's entire route upfront, the identity of which is quickly conveyed to
subsequent routers using a label in the packet header.
Components of MPLS
One of the defining features of MPLS is its use of labels -- the L in MPLS.
Sandwiched between Layers 2 and 3, a label is a four-byte -- 32-bit --
identifier that conveys the packet's predetermined forwarding path in an
MPLS network. Labels can also contain information related to quality of
service (QoS), indicating a packet's priority level.
MPLS labels consist of four parts:
1. The Label: The label holds all of the information for the MPLS routers
to determine where the packet should be forwarded.
2. Experimental: Experimental bits are used for Quality of Service (QoS)
to set the priority that the labeled packet should have.
3. Bottom-of-Stack: The Bottom-of-Stack tells the MPLS Router if it is

the last leg of the journey and there are no more labels to be
concerned with. This usually means the router is an egress router.
4. Time-To-Live: This identifies how many hops the packet can make
before it is discarded.
The paths, which are called label-switched paths (LSPs), enable service
providers to decide ahead of time the best way for certain types of traffic to
flow within a private or public network.
How an MPLS network works
In an MPLS network, each packet gets labeled on entry into the service
provider's network by the ingress router, also known as the label edge
router (LER). This is also the router that decides the LSP the packet will
take until it reaches its destination address.
All the subsequent label-switching routers (LSRs) perform packet

forwarding based only on those MPLS labels -- they never look as far as
the IP header. Finally, the egress router removes the labels and forwards
the original IP packet toward its final destination.
When an LSR receives a packet, it performs one or more of the following

actions:
 Push: Adds a label. This is typically performed by the ingress router.
 Swap: Replaces a label. This is usually performed by LSRs between

the ingress and egress routers.
 Pop: Removes a label. This is most often done by the egress router.
This diagram illustrates how a simple MPLS network works:
A visual of
how MPLS networks use path labels to direct traffic.
Benefits of MPLS
Service providers and enterprises can use MPLS to implement QoS by

defining LSPs that can meet specific service-level agreements (SLAs) on
traffic latency, jitter, packet loss and downtime. For example, a network
might have three service levels that prioritize different types of traffic -- e.g.,
one level for voice, one level for time-sensitive traffic and one level for best
effort traffic.
MPLS also supports traffic separation and the creation of virtual private
networks (VPNs), virtual private LAN services and virtual leased lines.
One of the most notable benefits of MPLS is that it is not tied to any one
protocol or transport medium. It supports transport over IP, Ethernet,
asynchronous transfer mode (ATM) and frame relay; any of these protocols
can be used to create an LSP. Generalized MPLS (GMPLS) extends MPLS
to manage time-division multiplexing (TDM), lambda switching and other
classes of switching technologies beyond packet switching.
Other benefits of MPLS include the following:
 It's good for real-time applications that can't tolerate latency, such as
video, voice and mission-critical data.
 Data and voice apps can all be run on the same MPLS network.
 Different types of data can be preprogrammed with different priorities

and classes of service.
 Organizations can assign different percentages of their bandwidth to

various types of data.
 MPLS networks are scalable. Companies only have to provision and

pay for the bandwidth they need until their requirements change.
History of MPLS
In 1994, Toshiba offered some ideas to the Internet Engineering Task

Force (IETF) that were the precursors to current MPLS standards. In 1996,
a team from Ipsilon Networks put forth a technology called IP switching that
was only intended to work on ATM networks. That same year, Cisco,
Ipsilon and IBM announced plans to use label switching, leading to
modern-day implementation of the protocol. In 1997, the first MPLS
working group was formed, and in 1999, the first deployment of an MPLS
network was completed.
MPLS was developed as a more effective alternative to multilayer switching

and IP over ATM. With MPLS, routers don't have to look up routes in
routing tables, boosting the speed of network traffic flow.
Because MPLS was created to work in a multiprotocol environment, it can

work with ATM, frame relay, Synchronous Optical Networking (Sonet) or
Ethernet at the core. MPLS continued to evolve as backbone network
technologies evolved. MPLS also played a major part in supporting legacy
network technologies, as well as the newer technology based on IP
networks. MPLS techniques were developed and adopted further in the
early 2000s, leading up to today's large-scale adoption of the protocol.

Multiprotocol Label Switching

Uploaded by

Copyright:

Available Formats

Multiprotocol Label Switching

Uploaded by

Document Information

Original Description:

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Multiprotocol Label Switching

Uploaded by

Copyright:

Available Formats

Multiprotocol Label Switching

MPLS allows most data packets to be forwarded at Layer 2 -- the switching

MPLS was created in the late 1990s as a more efficient alternative to

In an MPLS network, the first router to receive a packet determines the

MPLS labels consist of four parts:

3. Bottom-of-Stack: The Bottom-of-Stack tells the MPLS Router if it is

How an MPLS network works

All the subsequent label-switching routers (LSRs) perform packet

When an LSR receives a packet, it performs one or more of the following

 Push: Adds a label. This is typically performed by the ingress router.

 Swap: Replaces a label. This is usually performed by LSRs between

This diagram illustrates how a simple MPLS network works:

Service providers and enterprises can use MPLS to implement QoS by

 Different types of data can be preprogrammed with different priorities

 Organizations can assign different percentages of their bandwidth to

 MPLS networks are scalable. Companies only have to provision and

In 1994, Toshiba offered some ideas to the Internet Engineering Task

MPLS was developed as a more effective alternative to multilayer switching

Because MPLS was created to work in a multiprotocol environment, it can

You might also like