Northern Lights m1066 Parts

PARTS MANUAL
P1066
For Models: L1066T, L1066A, L1066H, M1066T,
M1066A1, M1066A2, M1066A3, M1066H,
M1066TMCA, NL1066T, NL1066H1, NL1066H2,
NL1066H3, NL1066H4, and M99C2
www.northern-lights.com
ULTRA LOW
SULFUR FUEL
ONLY RE529956
As of January 2011, U.S. EPA regulations require the

application of a permanently applied label near the fuel tank
fill port for diesel driven equipment. This label is to state:
ULTRA LOW SULFUR FUEL ONLY
Northern Lights is providing this label for application to the
fuel inlet of the fuel supply tank for each engine or generator
set. This is to be applied by the installer of the engine or gen
set, or by the manufacturer of the equipment that the engine
or gen set is installed in. The location of the label must be
in clear site of personnel that refill the supply tank.
— CALIFORNIA —
Proposition 65 Warning:
Breathing Diesel engine exhaust and some of its constituents
are known to the State of California to cause cancer, birth
defects, and other reproductive harm.
* Always start and operate the engine in a well-ventilated area.
* If in an enclosed area, vent the exhaust to the outside.
* Do not modify or tamper with the exhaust system.
* Do not idle the engine except as necessary.
For more information, go to www.P65warnings.ca.gov/diesel.
Northern Lights
4420 14th Avenue N.W.
Seattle, WA 98107
Tel: (206) 789-3880
Fax: (206) 782-5455
Copyright ©2016 Northern Lights, Inc.

All rights reserved. Northern Lights™, and
the Northern Lights logo are trademarks of
Northern Lights, Inc.
Printed in U.S.A.
PART NO.: P1066 12/18
PARTS CATALOG
for Models
L1066T, L1066A, L1066H, M1066T, M1066A1, M1066A2,
M1066A3, M1066H, M1066TMCA, NL1066T, NL1066H1,
NL1066H2, NL1066H3, NL1066H4, and M99C2
Please read thoroughly before attempting to use this manual:
Table of Contents............................................................................................................................................. I
Model Designation & Serial Numbers............................................................................................................... II
Reading a Parts Page...................................................................................................................................... III
Table of Contents
GROUP 4 - FUEL SYSTEM
GROUP 1 - ENGINE Fuel Injection Pump & Fuel Lines .................... 0 - 11
Cylinder Block Assembly .............................. 0 - 5 Engine Control Unit Applications ..................12 - 13
Flywheel & Housing ................................. 6 - 10 Fuel Injector ................................................14 - 17
Crankshaft & Main Bearings ............................ 11 Fuel Filter & Lines.............................. 18 - 33, 37 - 39
Crankshaft Pulley, Damper ......................... 12 - 16 Electric Fuel Pump............................................. 34 - 36
Cylinder Liner Assembly & Connecting Rod ..17 - 18 Fuel Filter Bypass...................................................... 40
Timing Cover Plate .................................. 19 - 22 Fuel Transfer Pump.................................................... 41
Camshaft .....................................................23 - 24 GROUP 5 - ELECTRICAL SYSTEM
Timing Cover ..............................................25 - 28 12 & 24 Volt, Standard & Isolated Ground.........0 - 17
Oil Filter Assembly, Mounting, & Adapter ..... 29 - 34 Alternator and Mounting ...............................18 - 33
Oil Pump.................................................................... 35 12 & 24 Volt Relay Board.................................. 34 - 39
Oil Pan............................................................... 36 - 38 Drive Belt Tensioner.......................................... 40 - 41
Oil Drain & Dipstick.......................................... 39 - 43 Idler Pulley & Mounting............................................ 42
Oil Fill Assembly............................................... 44 - 45 Drive Belts................................................................. 43
Cylinder Head, Head Gasket, Valves ............ 46 - 49 Engine Control Unit........................................... 44 - 45
Rocker Cover, Rocker Shaft, Rocker Arm......... 50 - 57 Control Panels.................................................... 46 - 53
Ventilating System..................................................... 58 Belt Guards........................................................ 54 - 69
GROUP 2 - INTAKE & EXHAUST GROUP 6 - GASKET SETS
Intake Manifold and Air Cleaner (Propulsion)......0 - 1 Engine Overhaul................................................0 - 4
Air Intake & Air Filter...........................2 - 3, 34 - 36 GROUP 7 - GEAR AND ADAPTER PARTS
Air Filter and Mounting........................... 4 - 6, 30 - 33 Gear Oil Cooler.................................................1 - 3
Crankcase Breather...............................................8 - 11 GROUP 8 - BASE FRAME & MOUNTING
Intake and Aftercooler..................... 7, 12 - 13, 24 - 25 Lifting Eyes.................................................................. 1
Exhaust Elbow.................................... 40 - 45, 48 - 49 Engine Mounting......................................................... 2
Exhaust Manifold............................................... 37 - 39 Base Frames......................................................... 3 - 15
Turbocharger Assemblies................... 14 - 23, 26 - 29, GROUP 9 - ACCESSORIES & OPTIONAL
46 - 47, 50 - 53 EQUIPMENT
GROUP 3 - COOLING SYSTEM Crankshaft Pulley......................................................... 0
Expansion Tank Assembly..................................0 - 3 Electric Clutch............................................................. 1
Heat Exchanger ...............................................4 - 7 PTO Adapter Parts..................................................2 - 4
Coolant Pump & Inlet.............................................8 - 9 Hydraulic Pump Drive Assembly................................ 6
Raw Water Pump & Mounting........................... 10 - 13 Low Oil Level Switch/Gauge...............................7 - 11
Thermostat & Housing....................................... 14 - 19 Air Intake Shut-off Valve........................................... 12
Engine Oil Cooler ........................................20 - 21 Low Coolant Level Switch/Gauge..................... 13 - 14
Idler Shaft Assembly ....................................22 - 24 Raw Water Flow Switch.................................... 15 - 17
Radiator & Mounting......................................... 24 - 33 Optional Alternators........................................... 18 - 19
Proprietary Information
This publication is the property of Northern Lights, Inc.
It may not be reproduced in whole or in part without the written permission of Northern Lights, Inc.
© Northern Lights, Inc. All rights reserved. Litho U.S.A. Publication number P1066 9/17
P1066 12/18
I
INTRODUCTION
MODEL DESIGNATION
Refer to the category designations below to find the correct parts pages for your model.
L - M - NL 1066 T-H
L - Lugger propulsion unit Base Model #

T Turbocharged
M - Northern Lights marine generator set 106 inch bore
H High Output
NL - Northern Lights industrial generator set 6 cylinders
Northern Lights turbocharged propulsion Northern Lights turbocharged industrial

L1066 T NL1066 T diesel generator set with a John Deere
engine with a John Deere engine and an
electronically controlled fuel system engine and an electronically controlled fuel
system.
Northern Lights propulsion engine with an
L1066 A aftercooled John Deere engine and an elec- Northern Lights high output industrial diesel
tronically controlled fuel system. NL1066 H2 generator set with a John Deere engine and
an electronically controlled fuel system.
Northern Lights turbocharged marine diesel
M1066 T generator set with a John Deere engine and
an electronically controlled fuel system. NL1066 H4 Northern Lights high output industrial diesel
generator set with a John Deere engine,
Northern Lights aftercooled marine diesel 4 valve, high pressure common rail fuel
M1066 A generator set with a John Deere engine system.
and an electronically controlled fuel
system.
M99C2 Northern Lights commercial marine
generator set with a John Deere engine,
Northern Lights turbocharged marine
M1066 H diesel generator set with a John Deere
Tier II.
engine, 4 valve, high pressure common rail
fuel system.
All model numbers in parentheses will indicate a John Deere base engine. All variations requiring serial
numbers for proper identification will be noted as ADE or John Deere.
SERIAL NUMBERS
NORTHERN LIGHTS
Your set has three serial numbers: 1 an engine number stamped on the block, 2 a generator plate, and
3 a generator set plate. Use the serial number on the generator set plate when ordering parts or in corre-
spondence. The generator set plate is found on the service side of the generator and resembles one of the
drawings below.
Lugger Serial Number Generator Set Serial Number
Generator Set Serial Number
P1066 12/18
II
INTRODUCTION
READING A PARTS PAGE
IMPORTANT:
Before selecting parts, be sure that you are choosing parts from the correct page.
Check the model designation at the page top.
Do not use this illustration for parts purchasing.
1 ELECTRICAL SYSTEM
ALTERNATOR ASSEMBLY: M - NL668
4 3 2
6 7 8 9
5 KEY PART NUMBER QTY. DESCRIPTION SERIALNUMBER
0 185046210 1 Alternator Assembly 10 -

1 185446219 1 Flywheel, complete -
2 185446217 1 Plate, complete -
3 185716200 1 Plate -
4 185446218 1 Stator, complete -
5 040126210 2 Bearing -
6 020210010 1 Nut -
7 027100010 1 Spring washer -
8 026100010 1 Washer -
9 185446220 1 Clamp -
10 015140408 1 Screw -
11 015140425 2 Screw -
12 199236510 1 Collar -
13 14
P668PT 08/00
11 5-2 12
REFERENCES:
1. Grouping section title. 7. Quantity of parts used.
2. Model designation of equipment that uses parts 8. Description of each component part.
listed on this page. 9. Serial number of unit the part fits.
3. Title and description of assembly. 10. Assembly or kit designated by Key 0 or ••/•.
4. Drawing numbers that correspond to key 11. Grouping index number.
column numbers for parts identification. 12. Page number within the grouping index.
5. Key column for locating parts shown on drawing. 13. Manual title.
6. Part number. 14. Page publication date.
NOTE: a Arrows always point toward the front of the engine.
P1066 12/18
III
Updated 7-27-16
GROUP 1 – ENGINE
Cylinder Block
L-M-NL1066T, M99C2, L1066A, M1066A, M1066A1,A2,A3, and NL1066H1,H2, H3
Reproduced by permission of Deere & Co., c2006. Deere & Company. All rights reserved. TP49642
P1066 12/18
1-0
Updated 7-27-16
GROUP 1 – ENGINE
Cylinder Block
L-M-NL1066T, M99C2, L1066A, M1066A, M1066A1,A2,A3, and NL1066H1,H2, H3
KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER

1 1 Cylinder Block (marked R119565 -
2 R114241 6 Bearing Cap
3 R132186 1 Bearing Cap (Thrust)
4 T23474 14 Capscrew
5 T20168 14 Washer
6 R119874 1 Bushing -
7 R132518 1 Plate -
8 19M7867 2 Capscrew, M8 x 25 -
9 R121043 1 Oil Bypass Valve -
10 R111137 1 Spring -
11 R26493 1 Bushing -
RE505501 1 Oil Pressure Regulating Valve -
12 R116466 1 Bushing -
13 R26650 2 Dowel Pin -
14 15H623 1 Pipe Plug, 3/8" -
15 R115390 1 Bushing -
16 R75892 1 O-ring -
17 R48685 2 Dowel Pin -
18 T18891 2 Plug -
19 R55233 1 Pipe Plug, 1/4" -
20 R104592 7 Pipe Plug
21 R131182 6 Orifice -
22 R39741 1 Drain Plug -
23 U13639 2 O-ring -
24 T43514 1 Gasket -
25 15H624 1 Pipe Plug, 1/2" -
26 AT13740 1 Drain Valve -
*Not available separately - see short block listing.
P1066 12/18
1-1
GROUP 1 – ENGINE
Cylinder Block
L- M1066H & NL1066H4
P1066 12/18
1-2
GROUP 1 – ENGINE
Cylinder Block
L- M1066H & NL1066H4

1 1 Cylinder Block (marked R504850)* -
2 R515365 6 Main Bearing Cap -
3 R515366 1 Thrust Bearing Cap -
4 T23474 14 Capscrew -
5 T20168 14 Washer -
6 R119874 1 Bushing -
7 R132518 1 Plate -
8 19M8999 2 Capscrew, M8 x 25 -
9 R121043 1 Oil Bypass Valve -
10 R111137 1 Spring -
11 R26493 1 Bushing -
RE505501 1 Oil Pressure Regulating Valve -
12 R116466 1 Bushing -
13 R26650 2 Dowel Pin -
14 15H623 1 Pipe Plug, 3/8" -
15 R115390 1 Bushing -
16 R75892 1 O-ring -
17 R48685 2 Dowel Pin -
18 T18891 2 Plug -
19 R55233 1 Pipe Plug, 1/4" -
20 R104592 7 Pipe Plug -
21 R131182 6 Orifice -
22 RE508185 1 Drain Plug -
23 U13639 2 O-ring -
24 T43514 1 Gasket -
25 15H624 1 Pipe Plug, 1/2" -
26 AT13740 1 Drain Valve -
27 D2361R 1 Ball (not shown) -
*Not available separately - see short block listing.
P1066 12/18
1-3
GROUP 1 – ENGINE
Cylinder Block
P1066 12/18
1-4
Updated 7-27-16
GROUP 1 – ENGINE
Cylinder Block
1 RE520385 1 Short Block Assembly (L-M-NL1066T, M99C2) -
RE520383 Short Block Assembly (L1066A, M1066A1,

A2, A3, and NL1066H1, H2, H3)
L1066A and M1066A1, A2, & A3 with VP44 pump also order
front plate kit RE509842. For NL1066A2 & A3 with VP44 pump also
order front plate kit RE509841.
2 RE522680 1 Short Block Assembly (L-M1066H and NL1066H4) -
P1066 12/18
1-5
GROUP 1 – ENGINE
Flywheel Housing SAE #2
Reproduced by permission of Deere & Co., c2006. Deere & Company. All rights reserved. RGP8234

1 R503453 1 Flywheel Housing SAE #2 -
2 RE44574 1 Seal -
3 R131769 1 Plug -
4 19M8306 4 Capscrew, M12 x 50 mm -
5 R135918 10 Bolt -
6 R39112 1 Fitting -
7 R61467 1 O-ring -
P1066 12/18
1-6
GROUP 1 – ENGINE

2 R61467 1 O-ring -
3 RE44574 1 Seal -
4 T13518 1 Plug -
5 15H624 1 Pipe Plug, 12.7 mm -
6 R121039 1 Plate -
7 19M7923 2 Capscrew, M6 x 12 -
8 R131769 1 Plug -
9 19M8306 4 Screw, M12 x 50 -
10 R135918 8 Bolt -
11 R39112 ** Plug -

**As required
P1066 12/18
1-7
GROUP 1 – ENGINE
For Dual Starter Applications

2 R131769 1 Plug -
3 R61467 1 O-ring -
4 RE44574 1 Seal -
5 15H624 1 Pipe Plug, 1/2" -
6 19M8306 4 Capscrew, M12 x 50 mm -
7 R135918 8 Bolt -
8 R39112 1 Fitting -
P1066 12/18
1-8
GROUP 1 – ENGINE
Flywheel SAE #11-1/2

1 RE500398 1 Flywheel (marked R500219)* -
2 R28811 1 Ring Gear (129 Teeth) -
3 R135918 6 Capscrew, Hex Head Flanged, M12 x 1.75 x 40 mm (Grade 10.9) -
*Not for use on applications with dual starters
P1066 12/18
1-9
GROUP 1 – ENGINE
Flywheel SAE #11-1/2

1 RE506389 1 Flywheel SAE #11-1/2 (marked R503802)* -
2 R28811 1 Ring Gear (129 Teeth) -
3 R135918 6 Capscrew, Hex Head Flanged, M12 x 1.75 x 40 mm (Grade 10.9) -
*Used on applications with dual starters
P1066 12/18
1 - 10
GROUP 1 – ENGINE
Crankshaft and Main Bearings

1 RE505921 1 Crankshaft (marked R503470) -
2 R133303 1 Shaft Key -
3 R120631 1 Gear (30 Teeth) -
4 R48685 1 Dowel Pin -
5 RE59811 1 Sleeve -
6 RE65165 6 Main Bearing Kit, (Standard, marked R123561 and R123562) -
RE65911 6 Main Bearing Kit (undersize .254 mm, marked R130576 and R130577) -
7 RE65168 1 Thrust Bearing Kit, (Standard marked R123563 and R123564) -
RE65912 1 Thrust Bearing Kit (undersize .254 mm, marked R130574 and R130575) -
P1066 12/18
1 - 11
GROUP 1 – ENGINE
Crankshaft Pulley and Damper
L- M1066T, M99C2, & M1066A2
Reproduced by permission of Deere & Co., c2006. Deere & Company. All rights reserved. CD43907A

1 RE505939 1 Pulley & Damper Assembly (188 mm O.D.) -
2 R516648 1 Capscrew, M20 x 2.5 x 70 mm Grade 12.9 -
3 R517237 1 Washer -
P1066 12/18
1 - 12
Updated 7-27-16
GROUP 1 – ENGINE
L1066A, M1066A, M1066A1, A3, & M1066H @ 1800 RPM
Reproduced by permission of Deere & Co., c2006. Deere & Company. All rights reserved.
RE508955PCDD01

1 RE508578 1 Pulley & Damper Assembly (188 mm O.D.)* -
2 R517237 1 Washer -
3 R516648 1 Capscrew M20 x 2.5 x 70 mm Grade 12.9 -
*Note: See Dual Damper parts detail for L1066A Pleasure Craft rating.
P1066 12/18
1 - 13
Updated 7-27-16
GROUP 1 – ENGINE
Dual Crankshaft Pulley and Damper
L1066A Pleasure Craft, L1066H All & M1066H @ 1500 RPM
Reproduced by permission of Deere & Co., c2006. Deere & Company. All rights reserved. RE508955PCDD01&CD43915

1 RE505941 1 Pulley & Damper Assembly (188 mm OD) -
2 R517237 1 Washer -
4 R504531 1 Spacer (without Accessory Pulley or PTO) -
R521066 1 Spacer (with Accessory Pulley or PTO) (former # 31-69603) -
5 RE57604 1 Torsional Damper -
6 19M8162 6 Capscrew, Hex Head Flanged M10 x 1.5 x 40 mm (Without -
accessory pulley or PTO) -
P1066 12/18
1 - 14
GROUP 1 – ENGINE
NL1066H1, H2, H3, H4
RGP9824

1 RE508577 1 Pulley & Damper Assembly (168 mm O.D.) -
3 R517237 1 Washer -

P1066 12/18
1 - 15
GROUP 1 – ENGINE
Crankshaft Pulley
A-10447, A-10449, A-10446, A-10448/ B-3732

1 34-69502 1 Pulley, Crankshaft, 3-A/B x 8" -
34-69501 1 Pulley, Crankshaft, 4-A x 8" -
2 01435-01065 6 Capscrew, Hex Head Flanged M10 x 1.5 x 65 mm (units with -
single damper)
19M7811 6 Capscrew, Hex Head Flanged M10 x 1.5 x 90 mm (units with -
dual damper)

P1066 12/18
1 - 16
Updated 1-20-12
GROUP 1 – ENGINE
Cylinder Liner Assembly and Connecting Rod

L- M- NL1066T, M99C2, L-1066A, M1066A1, A2, A3 and NL1066H1, H2, H3

•• RE507850 6 Piston Liner Kit (marked RE509540, includes # 7&8) Former # RE505112
1 M41029 12 Snap Ring -
2 R123177 6 Piston Pin -
3 R114082 6 Bushing -
4 R501124 12 Screw -
5 RE500608 6 Connecting Rod (marked R500335) -
6 RE65908 6 Bearing (Standard) -
RE65909 6 Bearing (undersize .010 mm) -
7 RE507852 6 Piston Ring Kit -
8 AR65507 6 O-ring Kit -
P1066 12/18
1 - 17
Updated 11-13-08
GROUP 1 – ENGINE
Cylinder Liner Assembly and Connecting Rod
L- M1066H & NL1066H4
•• RE516228 6 Piston Liner Kit (marked RE507758, includes keys #7-8) -

1 R54114 12 Snap Ring -
2 R502755 6 Piston Pin -
3 R114082 6 Bushing -
4 R501124 12 Screw -
5 RE500608 6 Connecting Rod (marked R500335, includes keys #3-4) -
6 RE65908 6 Bearing (Standard) -
RE65909 6 Bearing (Undersized .254 mm) -
7 RE516268 6 Piston Ring Kit -
8 AR65507 6 O-ring Kit -
P1066 12/18
1 - 18
GROUP 1 – ENGINE
Timing Cover Plate
M- L1066T, M99C2, L1066A, A1, A2, A3

1 R134526 1 Plate (L- M1066T & M1066A1 @ 60 Hz) -
R503550 1 Plate (L1066A - M1066A1 @ 50 Hz - M1066A2, A3) -
2 R134518 2 Stud -
3 R123174 1 Lock Washer -
4 R120641 1 Shaft, Upper (use with key #5) -
5 34H288 1 Spring Pin -
6 RE56313 1 Gear, Upper Idler (marked R120635, includes R130912) -
7 R131206 1 Thrust Washer -
8 19M8997 1 Screw, M10 x 65 mm -
9 R114194 1 Shaft, Lower -
11 R123584 4 Stud -
12 R136475 4 Screw -
13 19M8966 1 Screw, M10 x 50 mm -
15 R114193 1 Bushing -
16 RE56369 1 Gear -
17 R116386 3 Stud -
18 T20758 ** O-ring -
19 R135757 ** Cover (L- M1066T) -
**As required
P1066 12/18
1 - 19
GROUP 1 – ENGINE
Timing Cover Plate

NL1066T, H1, H2, H3
Reproduced by permission of Deere & Co., c2006. Deere & Company. All rights reserved. RGP8269/RGP7808

1 R134527 1 Plate (NL1066T- H1) -
R500711 1 Plate (NL1066H2- H3) -
2 R116386 3 Stud (NL1066T- H1) -
R134212 4 Stud (NL1066H2- H3) -
3 R134518 2 Stud -
4 R123584 4 Stud -
5 R101225 2 Thrust Washer (NL1066T- H1) -
R101225 1 Thrust Washer (NL1066H2- H3) -
R123174 1 Thrust Washer (NL1066H2- H3) -
6 R120641 1 Shaft, Upper -
7 34H288 1 Spring Pin -
8 RE56313 1 Gear (marked R120635) -
9 R131206 1 Thrust Washer, Upper Idler -
10 19M8997 1 Screw M10 x 65 mm -
12 R136475 ** Screw -
13 19M8966 1 Capscrew, M10 x 50 mm -
15 R114193 1 Bushing -
16 RE56369 1 Gear -
**As required
P1066 12/18
1 - 20
GROUP 1 – ENGINE
Timing Cover Plate
M & L1066H
Reproduced by permission of Deere & Co., c2006. Deere & Company. All rights reserved. RE506566SPA

1 R504282 1 Plate -
2 R134518 2 Stud -
4 R504843 1 Shaft -
5 R515408 1 Dowel Pin -
6 RE508489 1 Gear (marked R504614) -
7 19M7807 1 Capscrew, M10 x 60 -
8 19M8966 1 Capscrew, M10 x 50 -
10 R114193 1 Bushing -
11 RE56369 1 Gear -
14 R123584 7 Stud -
15 R136475 5 Screw -
P1066 12/18
1 - 21
GROUP 1 – ENGINE
Timing Gear Front Plate
NL1066H4

1 R504576 1 Plate -
2 R134518 2 Stud -
4 R504843 1 Shaft, Upper -
5 R515408 1 Dowel Pin -
6 RE508489 1 Gear (marked R504614) -
8 19M7807 1 Capscrew, M10 x 60 mm -
11 R123584 7 Stud -
12 R136475 5 Screw -
13 19M8966 1 Capscrew, M10 x 50 mm -
15 R114193 1 Bushing -
16 RE56369 1 Gear -
P1066 12/18
1 - 22
GROUP 1 – ENGINE
Camshaft
L- M- NL1066T, M99C2, L1066A, M1066A1, A2, A3, & NL1066H1, H2, H3

1 RE507149 1 Camshaft (marked R504535, includes keys #2-3) -
2 R133303 1 Shaft Key -
3 1 Gear (60 Teeth, marked R133812)* -
*Not available separately - order camshaft assembly
P1066 12/18
1 - 23
GROUP 1 – ENGINE
Camshaft Camshaft
L- M1066H and NL1066H4

1 RE515611 1 Camshaft (marked R515245, includes keys #2-3) -
2 R133303 1 Shaft Key -
3 1 Gear (60 Teeth, marked R516237)* -
*Not available separately - order camshaft assembly
P1066 12/18
1 - 24
Updated 7-27-16
GROUP 1 – ENGINE
Timing Gear Cover
L- M1066T, L1066A, M1066A, M1066A1, A2, A3

1 R504724 1 Cover (Replaced by R520129, also order installation kit RE515978) -
R520129 1 Cover
2 R136515 1 Gasket (use with cover R504724) -
R520131 1 Gasket (use with cover R520129)
3 RE517370 1 Plug -
4 51M7044 1 O-ring -
5 19M8317 10 Screw -
6 19M8291 1 Capscrew, M8 x 35 mm -
7 R121424 1 O-ring -
8 R121411 1 Cover -
9 19M7775 3 Capscrew, M6 x 16 mm -
10 RE67239 1 Capscrew -
11 RE505515 1 Seal Kit (formerly #RE59810) -
12 14M7296 6 Flange Nut, M10 -
13 19M7979 2 Screw -
14 19M7801 1 Capscrew, M8 x 60 mm -
P1066 12/18
1 - 25
Updated page 5-21-13
GROUP 1 – ENGINE
Timing Cover
L-M1066H

1 RE509865 1 Timing Gear Cover (former # RE50396) -
2 R516557 1 Adapter -
3 19M7805 4 Capscrew, M10 x 45 mm -
4 RE46687 1 Plug -
5 51M7045 1 O-ring -
6 51M7044 1 O-ring -
7 RE517370 1 Plug -
8 14M7296 9 Flange Nut, M10 -
9 19M7801 3 Capscrew, M8 x 60 mm -
11 19M7800 5 Screw -
12 R504734 1 O-ring -
13 R523184 1 Gasket (formerly #R503597) -
P1066 12/18
1 - 26
GROUP 1 – ENGINE
Timing Gear Cover
NL1066T, H1, H2, H3
Reproduced by permission of Deere & Co., c2006. Deere & Company. All rights reserved. RGP8338a

1 R504725 1 Cover (replaced by R520130 cover, R520132 gasket & RE515978 installation kit) -
R520130 1 Timing Cover -
2 R136516 1 Gasket (use with R504725) -
R520132 1 Gasket (use with R520130)
3 RE517370 1 Fitting Plug (includes key #4) -
4 51M7044 1 O-ring -
5 19M8317 10 Capscrew, M8 x 40 mm -
6 R121424 1 O-ring -
7 R121411 1 Cover -
8 19M7775 3 Capscrew, M6 x 16 mm -
9 19M8291 1 Capscrew, M8 x 35 mm -
10 RE67239 2 Capscrew, M8 x 45 mm -
11 14M7296 6 Flange Nut -
13 19M7801 1 Capscrew, M8 x 60 mm -
14 19M7979 2 Capscrew, M8 x 55 mm -
P1066 12/18
1 - 27
GROUP 1 – ENGINE
Timing Gear Cover
NL1066H4

1 RE503769 1 Timing Gear Cover -
2 R516557 1 Adapter -
3 19M7805 4 Capscrew, M10 x 45 mm -
4 RE46687 1 Plug -
5 51M7045 1 O-ring -
6 51M7044 1 O-ring -
7 RE501938 1 Plug -
8 14M7296 9 Flange Nut, M8 x 25 mm -
9 19M7801 3 Capscrew, M8 x 60 mm -
11 19M7800 5 Screw, M8 x 50 mm -
12 R504734 1 O-ring -
13 R502954 1 Gasket -
14 19M7867 1 Capscrew, M8 x 25 mm -
P1066 12/18
1 - 28
Updated 3-4-20
GROUP 1 - ENGINE
Oil Filter Assembly
L1066T
A-10760/ B-8749

1 31-79501 1 Adapter, Oil Filter Mounting (includes key #20) -
2 23-09601 1 Bracket, Oil Filter Adapter Mounting -
3 12-10815 1 Capscrew, Flangehead Socket M10 x 1.5 x 20 mm -
4 01435-01040 1 Capscrew, Hex Head Flanged M10 x 1.5 x 40 mm -
5 21-13110 1 Spacer -
6 12-00809 2 Capscrew, Hex Head M10 x 1.25 x 25 mm -
7 15-00804 2 Wave Washer M10 -
8 18-09401 1 Hose Assembly 1/2" ID x 16" -
10 21-09504 4 Male Connector Steel, M22 x 1.5 x 5/8 O-ring -
11 21-79503 2 Plug -
12 19M7802 4 Capscrew, M8 x 65 mm -
13 19M7913 1 Capscrew, M8 x 90 mm -
15 16-09501 4 O-ring -
16 RE52242 1 Plug -
17 51M7042 1 O-ring -
18 T77932 4 O-ring -
19 24-09501 1 Oil Filter -
20 R502513 1 Sealing Ring -
21 R123525 1 Gasket -
22 RE520814 1 Adapter -
P1066 12/18
1 - 29
Updated 3-4-20
GROUP 1 - ENGINE
Oil Filter Assembly

L1066A
A-10668/ B-8531

2 23-79605 1 Bracket, Oil Filter Adapter Mounting -
4 15-00802 2 Lock Washer M10 -
5 21-79503 2 Plug, Socket Head Steel M22 x 1.5 -
6 21-09504 3 Male Connector, Steel -
7 18-09603 1 Hose Assembly 1/2" ID x 17-1/2" -
9 19M7784 2 Capscrew, Hex Head Flanged M10 x 1.5 x 20 mm -
10 R123525 1 Gasket -
11 RE520814 1 Adapter (marked R123646, formerly #RE71062, includes keys 6, -
12, 16-18) -
12 RE52242 1 Plug -
13 19M7913 1 Capscrew, M8 x 90 mm -
15 19M7802 4 Capscrew, M8 x 65 mm -
16 21-09505 1 Elbow Fitting -
17 16-09501 4 O-ring -
18 T77932 4 O-ring -
19 24-09501 1 Oil Filter -
21 51M7042 1 O-ring -
P1066 12/18
1 - 30
Updated 3-4-20
GROUP 1 - ENGINE
Oil Filter Assembly
L1066H
A-10157/ B-8532

2 23-89612 1 Bracket, Rear Engine/ Oil Filter Mounting -
4 14-80811 2 Hex Nut Flanged, M10 x 1.5 -
5 21-79503 2 Plug, Socket Head Steel M22 x 1.5 -
6 21-09504 3 Male Connector, Steel -
9 12-10913 4 Capscrew, Flat Head Socket M12 x 1.75 x 25 mm -
10 R123525 1 Gasket -
11 RE520814 1 Adapter (marked R123646, formerly #RE71062, includes keys 6, -
12, 16-18) -
12 RE52242 1 Plug -
13 19M7913 1 Capscrew, M8 x 90 mm -
15 19M7802 4 Capscrew, M8 x 65 mm -
16 21-09505 1 Elbow Fitting -
17 16-09501 4 O-ring -
18 T77932 4 O-ring -
19 24-09501 1 Oil Filter -
21 51M7042 1 O-ring -
P1066 12/18
1 - 31
updated 3-21-13
GROUP 1 - ENGINE
Duplex Oil Filter Assembly
A-10882/ B-8875
P1066 12/18
1 - 32
updated 1-22-13
GROUP 1 - ENGINE
Duplex Oil Filter Assembly

1 RE71062 1 Adapter Assembly with Fittings -
2 R123525 1 Gasket, Oil Filter Adapter -
4 RE67238 1 Capscrew, Hex Head Flanged M8 x 1.25 x 20 mm -
6 21-09505 1 Male Elbow, 900 Steel M22 x 1.5 x 5/8 O-ring face -
7 21-09520 1 Branch Tee, Steel M22 x 1.5 x 5/8 O-ring -
8 18-09605 1 Hose Assembly 1/2" I.D. x 34" 5/8 O-ring face -
9 18-09604 1 Hose Assembly 1/2" I.D. x 31" 5/8 O-ring face -
10 21-09519 1 Male Elbow 900 Steel 5/8 O-ring port -
11 21-09521 1 Male Connector Steel 5/8 O-ring port -
12 23-79607 1 Bracket, Duplex Oil Filter Head Mtg. -
13 6151-55-5201 1 Duplex Oil Filter Assembly -
14 07000-63032 2 O-ring -
17 12-80514 4 Capscrew, Hex Head Flanged 1/2- 13 x 1- 1/2" -
18 14-00502 6 Lock Nut, Plain Flanged -
19 12-00512 2 Capscrew, Hex Head 1/2- 13 x 1" -
20 15-00504 2 Flat Washer 1/2" SAE -
21 21-50006 1 Male Elbow 900 Steel 3/8 O-ring port -
22 27-39613 1 Tube Assembly, Turbo Oil Supply -
23 RE52242 1 Plug -
24 51M7042 1 O-ring -
25 24-05701 2 Oil Filter -
26 16-09501 2 O-ring -
27 16-09502 4 O-ring -
28 16-72010 3 O-ring -
P1066 12/18
1 - 33
Updated 3-4-20
GROUP 1 - ENGINE
Oil Filter and Adapter
M- NL1066

1 RE504562 1 Filter Head (marked R502338, includes keys #2-3) -
2 RE504543 1 Valve -
3 R502513 1 Seal -
4 R501484 1 Gasket -
5 19M7802 5 Capscrew, M8 x 65 mm -
7 RE52242 ** Plug, M16 x 1.5 (includes key #8) -
8 51M7042 ** O-ring -
9 RE504836 1 Oil Filter -
**As required
P1066 12/18
1 - 34
GROUP 1 - ENGINE
Oil Pump

1 RE502269 1 Oil Pump (marked R123179, includes keys 2-5, 8)
2 1 Cover* -
3 1 Gear* -
4 1 Housing* -
5 1 Gear* -
6 19M8987 2 Capscrew, M8 x 65 mm -
7 R121376 1 Tube -
8 R97185 1 O-ring -
9 14M7066 1 Nut, M12 -
10 R120638 1 Gear -
*Not available separately

P1066 12/18
1 - 35
GROUP 1 - ENGINE
Oil Pan
L- M1066T, M99C2

1 R134898 1 Oil Pan (Aluminum) -
2 R123354 1 Gasket -
3 R61871 1 O-ring -
4 RE71143 1 Oil Pump Pick-up -
5 15H624 ** Pipe Plug, 1/2" -
6 19M8986 2 Capscrew, M8 x 100 mm -
7 12-80753 6 Capscrew, M8 x 30 mm -
8 19M7867 26 Capscrew, M8 x 25 mm -
9 16-09503 ** O-ring -
10 RE46685 ** Plug -
11 19M7799 4 Capscrew, M8 x 45 mm -
12 16-09501 2 O-ring -
13 RE46687 2 Plug -
**As required
P1066 12/18
1 - 36
Updated 7-27-16
GROUP 1 - ENGINE
Oil Pan
L1066A- H, M1066A, A1, A2, A3, H and NL1066H1, H2, H3, H4

1 RE509666 1 Oil Pan (Steel - O-ring seals used at ports, replaced by RE523256) -
RE523256 1 Oil Pan (Steel - bonded sealing washers used at ports) 32.5 litre -
36-79602 1 Oil Pan (Steel - Modified with extra sensor ports) -
2 RE71143 1 Oil Pump Pick-up -
3 R61871 1 O-ring -
4 R521498 1 Gasket (formerly #R500349) -
5 19M8986 2 Capscrew, M8 x 100 mm -
6 19M8062 6 Capscrew, M8 x 20 mm -
7 19M8163 30 Capscrew, M8 x 16 mm -
8 16-09501 ** O-ring (use with pan RE509666) -
R519742 ** Sealing Washer, Bonded M22 (use with pans RE523256 & 36-79602) -
9 RE46687 ** Drain Plug -
RE523251 1 Plug with sealing washer -
10 16-09501 2 O-ring -
11 RE46687 2 Drain Plug -
12 19M7799 4 Capscrew, M8 x 45 mm -
**As required
P1066 12/18
1 - 37
GROUP 1 - ENGINE
Oil Pan
NL1066T
RGP7618

1 RE500612 1 Oil Pan (Steel) -
2 R500349 1 Gasket -
3 R61871 1 O-ring -
4 19M8986 2 Capscrew, M8 x 100 mm -
5 RE71143 1 Oil Pump Intake -
6 19M7866 6 Capscrew, M8 x 20 mm -
7 19M8163 30 Capscrew, M8 x 16 mm -
8 16-09501 1 O-ring -
9 RE46687 1 Plug -
P1066 12/18
1 - 38
GROUP 1 - ENGINE
Oil Drain
M1066T, M99C2
A-8425/ B-1563

1 21-79601 1 Female Swivel, Steel, M18 x 1.5 x 3/8-37T -
2 21-00026 1 Female Elbow 900, Steel, 3/8 NPT x 3/8-37T -
3 36-71002 1 Shut off Valve -
4 21-71042 2 Female Swivel, Brass, 1/2 Hose Barb x 1.2-45T -
5 41-01032 18" Hose, 1/2" I.D. -
6 21-71040 1 Male Connector, Brass, 1/2 NPT x 1/2-45T -
7 21-10005 1 Plug, Hex Head, Steel, 1/2 NPT -
8 16-09503 1 O-ring (for adapter #1 - not shown) -
P1066 12/18
1 - 39
GROUP 1 - ENGINE
Oil Drain Assembly
M1066A- H
A-10827/ B-8683

1 21-60013 1 Male Elbow, 90º Steel M22 x 1.5 x 1/2- 37T -
2 18-61603 1 Hose Assembly 1/2" I.D. x 25" - Early production -
18-75701 1 Hose Assembly 1/2" I.D. x 32" - Late production -
3 36-71002 1 Shut-off Valve, Brass 3/8 NPT x 1/2- 4 -
4 21-09513 ** Bulkhead Union, Steel 3/8 NPT - Early production -
5 21-31003 1 Plug, Hex Head Brass 3/8 NPT -

**As required
P1066 12/18
1 - 40
GROUP 1 - ENGINE
Oil Drain
NL1066T
A-8458B/ A-11457

1 21-79601 1 Female Swivel, Steel M18 x 1.5 x 3/8-37T -
2 21-00026 1 Female Elbow 900 Steel 3/8 NPT x 3/8-37T -
3 36-71002 1 Shut-off Valve, Brass 3/8 NPT -
4 21-71042 1 Female Swivel, Brass 1/2 HB x 1/2-45T -
5 41-01032 15 Hose, 1/2" I.D. -
7 21-60017 1 Elbow 900 Swivel, Steel 1/2-37T -
8 21-01017 1 Female Bulkhead Connector Steel 3/8 NPT x 1/2- 37T -
10 14-01225 1 Nut, Bulkhead -
11 16-09503 1 O-ring (for swivel #1 - not shown) -
P1066 12/18
1 - 41
GROUP 1 - ENGINE
Oil Drain Assembly
NL1066H1, H2, H3, H4
A-10662/ A-11457

1 21-60007 1 Female Adapter Steel, 1/2 NPT x M22 x 1.5 -
2 21-00055 1 Street Elbow 900 Steel, 1/2 NPT x 3/8 NPT -
3 36-71002 1 Shut-off Valve, Brass 3/8 NPT x 1/2- 4 -
5 41-01032 15 Hose, 1/2" I.D. Push-on -
7 21-60017 1 Elbow, 900 Swivel, Steel 1/2-37T -
8 21-01017 1 Female Bulkhead Connection, Steel 3/8 NPT x 1/2 -
9 21-31003 1 Plug, Hex Head, Brass 3/8 NPT -
10 14-01225 1 Nut, Bulkhead 3/4-16 -
11 16-09501 1 O-ring (for adapter #1 - not shown) -
P1066 12/18
1 - 42
GROUP 1 - ENGINE
Oil Dipstick

1 RE69243 1 Dipstick -
2 R502604 1 Dipstick Tube, Right Hand -
R130055 1 Dipstick Tube, Left Hand -
3 R502725 ** Plug (for unused tube location) -
**As required
P1066 12/18
1 - 43
GROUP 1 - ENGINE
Oil Fill Assembly

Right Side or Left Side
A-8347/ B-5846

1 36-01002 1 Oil Filler Neck -
2 11-79501 1 Oil Filler Mounting Gasket -
3 12-00714 2 Capscrew, Hex Head, M8 x 1.25 x 40 mm -
4 15-00701 2 Flat Washer, M8 -
5 198436010 1 Oil Fill Cap -
6 052300400 1 O-ring -
7 21-00012 ** Plug, Hex Head, Brass, 1/8 NPT -
**As required

P1066 12/18
1 - 44
GROUP 1 - ENGINE
Oil Fill Cover

1 R116296 2 Cover -
2 R136495 3 Gasket -

P1066 12/18
1 - 45
GROUP 1 - ENGINE
Cylinder Head, Head Gasket, & Valves

L- M- NL1066T, M99C2, L1066A, M1066A1, A2, A3, and NL1066H1, H2, H3
P1066 12/18
1 - 46
GROUP 1 - ENGINE

1 RE57489 1 Cylinder Head Assembly (marked R121608, includes keys 2-6 & 8-13) -
2 T58477 1 Fitting -
3 R43409 3 Plug -
4 R98063 6 Valve Seat Insert, Standard Intake Valve -
R98335 6 Valve Seat Insert, Oversize Intake Valve -
R85687 6 Valve Seat Insert, Standard Exhaust Valve -
R93910 6 Valve Seat Insert, Oversize Exhaust Valve -
5 CD16284 1 Plug -
6 R104592 1 Pipe Plug -
7 15H624 1 Pipe Plug, 1/2" -
8 R98062 6 Intake Valve, Standard -
R97490 ** Intake Valve, .015" Oversize -
R97491 ** Intake Valve, .030" Oversize
9 R90692 6 Exhaust Valve, Standard -
R97492 ** Exhaust Valve, .015" Oversize -
R97493 ** Exhaust Valve, .030" Oversize -
10 RE31617 12 Seal -
11 R26125 12 Spring -
12 RE60005 12 Rotator -
13 R91889 24 Retainer -
14 R116516 1 Engine Cylinder Head Gasket -
15 R85363 26 Capscrew -
**As required
P1066 12/18
1 - 47
GROUP 1 - ENGINE

L- M1066H, NL1066H4
P1066 12/18
1 - 48
Updated 1-7-14
GROUP 1 - ENGINE

L- M1066H, NL1066H4

1 RE507777 1 Cylinder Head Assembly (includes keys 2-6 & 8-16) -
2 R502371 48 Retainer -
3 R502367 24 Cap -
4 R503906 24 Compression Spring -
5 RE519115 24 Seal -
6 CD16284 5 Plug -
7 R502512 6 Sleeve* -
8 RE518082 12 Valve Seat Insert, Intake -
9 RE518083 12 Valve Seat Insert, Exhaust -
10 R502369 12 Intake Valve -
11 R502370 12 Exhaust Valve -
12 15H624 1 Pipe Plug, 1/2" -
13 R104592 1 Pipe Plug -
14 RE530609 6 O-ring (marked R121608) -
15 RE528349 6 O-ring (marked R121608) -
16 RE517435 6 Sleeve (includes #14-15) -
17 R116516 1 Head Gasket -
18 R502511 26 Screw -
* Now Supplied Separately
P1066 12/18
1 - 49
updated 1-29-09
GROUP 1 - ENGINE
Rocker Arm Assembly & Push Rods

1 R54565 2 Plug -
2 R123514 1 Rocker Arm Shaft -
3 T20316 2 Washer -
4 T20314 3 Spring -
5 R123271 6 Stud -
6 R42729 6 Washer -
7 R123161 6 Support -
8 RE508317 12 Rocker Arm (includes keys 9 & 10) -
9 14M7148 1 Nut, M10 -
10 R133630 12 Adjusting Stud -
11 R107731 12 Push Rod -
12 R123565 12 Cam Follower -

P1066 12/18
1 - 50
GROUP 1 - ENGINE
Notes
P1066 12/18
1 - 51
Updated 1-10-08
GROUP 1 - ENGINE
Rocker Shaft Assembly and Push Rods
RGP9585
P1066 12/18
1 - 52
Updated 1-10-08 & 11-13-08
GROUP 1 - ENGINE
Rocker Shaft Assembly and Push Rods

•• RE519895 1 Rocker Arm Shaft Assembly (includes keys 1-3, 7-9, 11-12) -
1 19M9170 2 Capscrew, M8 x 50 mm -
2 R504631 2 Cap -
3 RE516491 1 Rocker Arm Shaft -
4 24M7096 ** Washer -
5 R519292 7 Bolt (Tapped M6 x 1.0, formerly #R504636)* -
R521458 7 Bolt (Tapped M8 x 1.25)* -
6 R516140 5 Strap -
7 14M7148 1 Nut, M10 -
8 RE523023 6 Rocker Arm, Intake (replaces RE504209) -
9 RE504210 6 Rocker Arm, Exhaust -
10 R502341 12 Lever -
11 R505543 6 Spring -
12 R504629 1 Support -
R519739 1 Support (replaces R504629) -
13 R47154 1 O-ring (use with R504629)
R72328 1 O-ring (use with R519739) -
14 R504882 1 Gasket -
15 R504209 12 Push Rod -
16 R123565 12 Follower -
*See Rocker Arm Cover assembly detail

**As required

P1066 12/18
1 - 53
GROUP 1 - ENGINE
Rocker Arm Cover
L-M1066T, M99C2, L1066A, & M1066A1, A2, A3
A-8282/ C-4163

1 10-09602 1 Rocker Arm Cover -
2 14-71002 6 Hex Nut, M8 x 1.25 x 53.5 mm, Special -
3 15-09007 6 Flat Washer, M12 S/S -
4 16-15005 6 O-ring -
5 R123543 1 Gasket, Rocker Arm Cover Mounting -
6 R120467 1 Elbow, Vent System Connection -
7 16-01000 1 O-ring -
8 00-09504 1 Label, "Powered by Lugger" -
00-09507 1 Label, "Northern Lights"
9 41-00004 ** Hose, 3/4" I.D. (sold per inch) -
10 21-00025 ** Vent Elbow -
**As required
P1066 12/18
1 - 54
Revised 7-3-08
GROUP 1 - ENGINE
Rocker Arm Cover
L-M1066H
A-10156/ C-5747

1 10-09604 1 Rocker Arm Cover -
2 12-99501 7 Capscrew, Hex Head Special M6 x 1.0 x 78.8 mm S/S* -
12-99502 7 Capscrew, Hex Head Special M8 x 1.25 x 78.8 mm S/S* -
3 15-09007 7 Flat Washer, M12 S/S -
4 16-15005 7 O-ring -
5 R504882 1 Gasket, Rocker Arm Cover Mounting -
6 R120467 1 Elbow, Vent System Connection -
7 16-01000 1 O-ring -
8 00-09507 1 Label, "Northern Lights" -
9 41-00004 ** Hose, 3/4" I.D. (sold per inch - see Air Filter details) -
10 21-00025 1 Vent Elbow, 3/4" Hose Barb -
*Verify thread per application.
P1066 12/18
1 - 55
GROUP 1 - ENGINE
Rocker Arm Cover
NL1066T, H1, H2, H3
Reproduced by permission of Deere & Co., c2006. Deere & Company. All rights reserved. RGP6461/ TP55085

1 RE502987 1 Rocker Arm Cover -
2 R123543 1 Gasket -
3 H23125 6 Plug -
4 R123574 6 Nut -
5 R123575 6 O-ring -
6 RE500005 1 Filler Cap (includes key #7) -
7 R502902 1 Packing -
8 00-09508 1 Nameplate "Northern Lights" -
P1066 12/18
1 - 56
GROUP 1 - ENGINE
Rocker Arm Cover
NL1066H4

1 RE515428 1 Valve Cover -
2 R515555 1 Deflector
3 19M7775 2 Screw
4 R504882 1 O-ring
5 R516181 7 Screw
6 R516158 7 O-ring
7 H23125 7 Plug
8 R516174 1 Heat Shield -
9 19M7774 3 Capscrew, M6 x 12 mm
10 19M8017 2 Capscrew, M12 x 20 mm -
11 24M7047 2 Washer -
12 RE500005 1 Filler Cap -
13 R502902 1 Packing -
P1066 12/18
1 - 57
GROUP 1 - ENGINE
Ventilating System
NL1066T, H1, H2, H3, H4
TP61896

1 R120467 1 Elbow Fitting, 900 -
2 R72328 1 O-ring -
3 R72659 1 Clamp* -
4 19M7866 1 Screw, M8 x 20 -
5 41-00004 53" Hose, 3/4" I.D. -

P1066 12/18
1 - 58
GROUP 1 - ENGINE
Notes
P1066 12/18
1 - 59
GROUP 2 - INTAKE AND EXHAUST SYSTEMS
Intake, Turbocharger, and Air Filter Assembly
L1066T
A-10698 / C-5305

1 30-31627-1 1 Turbocharger - K27 -
2 11-31615 1 Gasket -
3 13-00814 4 Stud, M10 x 1.5 x 30 mm (42 mm LOA) -
4 14-00817 4 Hex Nut, M10 x 1.5 S/S -
5 15-00804 4 Wave Washer, M10 -
6 18-21016 1 Hose, 2" I.D. x 1-3/4" 3 Ply Silicone -
7 19-01028 4 Hose Clamp #28 -
P1066 12/18
2-0
L1066T
8 27-21010 1 Intake Tube Assembly (includes keys 60-62) -

9 18-21014 1 Hose, 2" I.D. x 2-3/8" -
10 10-21607 1 Intake Manifold -
11 11-21011 1 Gasket -
15 15-00804 3 Wave Washer M10 -
17 11-31031 1 Gasket -
18 27-31602 1 Pipe, Turbo Oil Return (Upper) -
20 15-00702 4 Lock Washer, Helical M8 -
21 18-11010 1 Hose 3/4" ID x 4-1/4" 3 Ply Silicon -
22 19-01012 2 Hose Clamp #12 -
23 27-31402 1 Pipe, Turbo Oil Return (Lower) -
24 R41285 2 Adapter -
25 16-01000 2 O-ring -
26 R43928 1 Adapter -
27 11-31012 1 Gasket -
29 21-52800 1 Male Connector, Steel 3/8 NPT x 3/8- 37T -
30 27-39603 1 Tube Assembly, Turbo Oil Supply (supercedes 27-39602) -
31 21-09501 1 Male Elbow 900 Steel M16 x 1.5 x 3/8- 37T -
32 21-10002 1 Drain Cock, Brass 1/4 NPT -
33 19-72252 1 Adelle Clamp 3/8" ID x 3/8" Stud -
36 15-00701 1 Flat Washer M8 -
37 21-09512 1 Female Adapter, Steel 3/4 O-ring Port x 1-1/4 O-ring Port -
38 21-00032 1 Male Elbow 900 Steel 3/4 O-ring Port x 3/4- 37T -
39 27-19605 1 Tube Assembly, Turbo Coolant Supply -
43 27-39601 1 Tube Assembly, Turbo Coolant Return -
44 21-03459 1 Female Elbow 900 Steel -
45 18-21003 1 Hump Hose 4" x 2-3/4" x 4" LOA -
46 19-00044 1 Hose Clamp #44 -
47 19-00072 1 Hose Clamp #72 -
48 24-21000 1 Air Filter -
49 23-21000 1 Bracket, Air Filter Mtg. -
52 15-00805 2 Flat Washer M10 -
53 19-00128 1 Hose Clamp #128 -
54 21-00025 1 Male Elbow 900 PVC 3/4 HB x 3/4 HB -
55 41-00004 9 Hose 3/4" ID 1 Ply, SAE -
56 13-00814 4 Stud M10 x 1.5 x 30 mm -
57 14-00817 4 Hex Nut M10 x 1.5 S/S -
58 15-00804 4 Wave Washer M10 -
60 27-21002 1 Tube -
61 16-21001 2 O-ring -
62 27-21001 2 Intake Elbow -
P1066 12/18
2-1
M1066T, M99C2
A-8426, A-8427 / C-4157
P1066 12/18
2-2

M1066T, M99C2

1 30-31426-1 1 Turbocharger (see Parts Detail) -

2 11-31401 1 Gasket -
3 13-00814 4 Stud, M10 x 1.5 x 30 mm (42 mm LOA) -
4 14-00817 4 Hex Nut, M10 x 1.5 S/S -
5 15-00804 4 Wave Washer, M10 -
6 18-21016 1 Hose, 2” I.D. x 1-3/4” 3 Ply Silicone -
7 19-01028 4 Hose Clamp #28 -
8 27-21010 1 Intake Tube Assembly (Includes keys #50-52) -
9 18-21014 1 Hose, 2” I.D. x 2-3/8” -
10 10-21607 1 Intake Manifold -
11 11-21011 1 Gasket -
14 15-00804 3 Wave Washer, M10 -
16 11-31031 1 Gasket -
20 18-11010 1 Hose, 3/4” I.D. x 4-1/4” -
21 19-01012 2 Hose Clamp #12 -
23 R41285 1 Adapter -
24 16-01000 1 O-ring -
25 R43928 1 Adapter -
26 11-31012 1 Gasket -
27 12-00714 2 Capscrew, Hex Head M8 x 1.25 x 40 mm, all thread -
28 21-52800 1 Male Connector, Steel 3/8 NPT x 3/8-37T -
29 27-09601 1 Tube Assembly, Turbocharger oil supply -
30 21-09502 1 Male Connector, Steel 3/8-37T x M16 x 1.5 -
31 21-52213 1 Elbow, 90° Swivel, Steel 3/8-37T -
32 19-72252 1 Adelle Clamp, 3/8” I.D. x 3/8” Stud -
35 15-00701 1 Flat Washer, M8 -
36 18-21004 1 Hump Hose -
37 19-00036 1 Hose Clamp #36 -
38 19-00072 1 Hose Clamp #72 -
39 24-21000 1 Air Filter -
40 23-21003 1 Bracket -
43 15-00805 2 Flat Washer, M10 -
44 19-00128 1 Hose Clamp #128 -
45 21-00025 1 Male Elbow, 90° PVC 3/4 HB x 3/4 HB -
46 41-00004 8.3” Hose, 3/4” I.D. 1 Ply -
47 21-00077 1 Female Adapter, Steel 1/8 NPT x M22 x 1.5 -
48 15-09501 1 Sealing Washer, Copper M22 -
50 27-21002 1 Intake Tube -
51 16-21001 2 O-ring -
52 27-21001 2 Intake Elbow -
P1066 12/18
2-3
Air Filter and Mounting
L1066A & M1066A1-A2 @ 60 Hz & M1066A3
A-10885/ B-8822

1 24-21000 1 Air Filter -
2 18-22504 1 Hump Hose 4" ID x 5-1/4" LOA (L1066A - M1066A1-A2 @ 60 Hz) -
18-21003 1 Hump Hose 4" ID x 2- 3/4" I.D. x 4" LOA (M1066A3) -
3 19-00072 1 Hose Clamp #72 -
6 19-00128 3 Hose Clamp #128 -
7 21-00025 1 Male Elbow, 90º PVC 3/4 HB x 3/4 HB -
8 41-00004 ** Hose 3/4" ID (Sold per inch) -
9 19-00044 1 Hose Clamp #44 (M1066A3) -
**As required
P1066 12/18
2-4
Updated 7-27-16
M1066A & M1066A1-A2 @ 50 Hz
A-10680/ B-8838

1 24-21000 1 Air Filter -
2 18-29501 1 Hump Hose 4-1/8" ID x 4-3/4" LOA -
3 19-00072 1 Hose Clamp #72 -
6 19-00128 3 Hose Clamp #128 -
7 21-00025 1 Male Elbow, 90º PVC 3/4 HB x 3/4 HB -
8 41-00004 12" Hose 3/4" ID (Sold per inch) -
9 19-00036 1 Hose Clamp #36 -
P1066 12/18
2-5

L1066H
A-10256/ B-8869

1 24-25001 1 Air Filter Housing -
2 18-24806 1 Hump Hose 6" ID x 4" x 3-1/4" LOA -
3 24-25003 1 Rubber Bushing 5-1/2" I.D. x 6" O.D. -
4 19-00072 1 Hose Clamp #72 -
5 19-00096 1 Hose Clamp #96 -
8 19-00128 1 Hose Clamp #128 -
9 24-25002 1 Air Filter Element -
10 21-00025 1 Male Elbow, 900 PVC 3/4 HB x 3/4 HB
P1066 12/18
2-6
Intake and Aftercooler Assembly

M1066H
A-11037/ B-8646

1 24-21000 1 Air Filter -
2 18-21003 1 Hump Hose 4" x 2-3/4" x 4" -
3 19-00072 1 Hose Clamp #72 -
4 27-29604 1 Tube, Air Intake -
5 18-29601 1 Hose 2-3/4" ID x 3" 3 Ply Silicone -
6 19-01048 3 Hose Clamp #48 Extended Band S/S -
9 19-00128 1 Hose Clamp #128 -
10 21-00025 1 Male Elbow 90° PVC 3/4 HB x 3/4 HB -
11 41-00004 Hose 3/4" ID -
P1066 12/18
2-7
Crankcase Breather Filter Assembly
L-M1066H
A-12093/ B-9418
P1066 12/18
2-8
L-M1066H

1 24-20015 1 Crankcase Breather Filter, Left hand Inlet -
2 23-29606 1 Bracket, Crankcase Breather Filter Support -
3 19M7866 4 Capscrew, Hex Head Flanged M8 x 1.25 x 20 mm Grade 10.9 -
5 14-80811 2 Hex Nut, Flanged M10 x 1.5 -
6 R120467 1 Elbow, 900 3/4 HB with o-ring -
7 16-01000 1 O-ring -
8 41-01050 68" Hose, 3/4" I.D. Wire Reinforced SAE J1527 A-2 USCG-20 +2120F -
9 21-20003 1 Male Connector, PVC 7/8 O-r Port x 3/4 HB -
10 21-20007 1 Female Adapter, Steel 3/4 NPT x 7/8 O-r Port -
11 21-20006 1 Male Elbow 900 Nylon 3/4 NPT x 3/4 HB -
12 21-71034 2 Female Swivel, Brass 3/8 HB x 3/8-37T Push-on -
13 41-01020 16 Hose, 3/8" I.D. Push-on -
14 21-20002 1 One way Valve, Brass 1/4 NPT x 3/8-37T -
15 21-00034 1 Street Elbow 450 Brass 1/4 NPT -
16 21-00044 1 Hex Coupling Brass 1/4 NPT -
17 21-71041 1 Close Nipple Brass 1/4 NPT -
19 21-79504 1 Female Adapter Steel 1/4 NPT x M22 x 1.5 -
20 19-00000 1 Adelle Clamp 15/16" I.D. x 3/8" Stud -
21 19-00012 4 Hose Clamp #12 -
22 16-09501 1 O-ring -
P1066 12/18
2-9
Updated 7-27-16
M1066A & M1066A1 - A2 - A3
A-12091, A-12092/ B-9420
P1066 12/18
2 - 10
Updated 7-27-16
M1066A & M1066A1 - A2 - A3

1 24-20015 1 Crankcase Breather Filter, Left hand Inlet -
2 23-29607 1 Bracket, Crankcase Breather Filter Support -
5 R120467 1 Elbow, 900 3/4 HB with o-ring -
6 16-01000 1 O-ring -
7 41-01050 58" Hose, 3/4" I.D. Wire Reinforced SAE J1527 A-2 USCG-20 +2120F -
8 21-20003 1 Male Connector, PVC 7/8 O-ring Port x 3/4 HB -
9 21-20007 1 Female Adapter, Steel 3/4 NPT x 7/8 O-ring Port -
10 21-20006 1 Male Elbow 900 Nylon 3/4 NPT x 3/4 HB -
12 41-01020 38" Hose, 3/8" I.D. Push-on -
13 21-20002 1 One way Valve, Brass 1/4 NPT x 3/8-37T -
15 21-00044 1 Hex Coupling Brass 1/4 NPT -
16 21-71041 1 Close Nipple Brass 1/4 NPT -
19 12-80832 2 Capscrew, Hex Head Flanged M10 x 1.5 x 30 mm Grade 10.9 -
20 19-00012 4 Hose Clamp #12 -
21 16-09501 1 O-ring -
P1066 12/18
2 - 11
Updated 7-27-16

L1066A & M1066A - M1066A1 - A2 - A3
A-10285/ C-5652z
P1066 12/18
2 - 12
Updated 7-27-16

L1066A & M1066A - M1066A1 - A2 - A3

1 10-29604 1 Manifold, Intake and Aftercooler -
2 16-29502 2 O-ring -
4 20-29601-1 1 Element, Intake Aftercooler -
5 16-09601 2 O-ring -
6 10-29603 1 Aftercooler Cover -
8 12-00733 2 Capscrew, Hex Head M8 x 1.25 x 180 mm (Grade 8.8) -
10 15-00706 4 Flat Washer M8 S/S -
13 16-09504 2 O-ring -
14 28-09501 3 Threaded Plate (3 Places) -
16 19M7866 13 Capscrew, Hex Head Flanged, M8 x 1.25 x 20 mm -
18 14M7298 4 Hex Nut, Flanged M8 x 1.25 -
19 27-09503 1 Connector, Raw Water Pump Outlet -
20 27-09504 1 Connector, Aftercooler Outlet -
21 16-13101 2 O-ring -
22 21-00027 1 Plug, Socket Head Brass 1/8 NPT -
23 21-10002 1 Drain Cock Brass 1/4 NPT -
24 18-26002 3 Hose, 2" ID x 3-3/4" 4 Ply Silicone -
25 19-01032 6 Hose Clamp #32 -
26 27-19514 1 Tube, Heat Exchanger Inlet -
29 15-00904 1 Wave Washer -
30 10-29504 1 Connector, Aftercooler Intake -
31 11-29501 1 Gasket -
33 15-00804 2 Wave Washer M10 -
35 21-09516 1 Male Connector, S/S 3/8- 37T x 3/8 -
36 27-29603 1 Tube Assembly, Aftercooler Condensate -
37 21-29504 1 Drain, Aftercooler Condensate -
38 19-72252 2 Adelle Clamp, 3/8" I.D. -
39 12-00776 2 Capscrew, Hex Head M8 x 1.25 x 20 mm S/S -
40 15-00705 2 Lock Washer, Helical M8 S/S -
41 15-00701 2 Flat Washer, M8 -
P1066 12/18
2 - 13
Turbocharger and Mounting Assembly
L1066A
A-10699 / C-5584
P1066 12/18
2 - 14
L1066A
1 30-39627 1 Turbocharger, K27 -

2 11-31615 1 Gasket, Turbo Mounting -
3 13-00814 4 Stud, M10 x 1.5 x 30 mm -
4 14-00818 4 Hex Nut, M10 x 1.5 S/S -
5 15-00804 4 Wave Washer M10 -
6 11-31031 1 Gasket, Turbo Oil Return -
10 18-11010 1 Hose, 3/4" ID x 4-1/4" 3 Ply Silicone -
11 19-01012 2 Hose Clamp, #12 Extended Band S/S -
13 R41285 2 Adapter, O-ring Seal x 1/2 NPT -
14 16-01000 2 O-ring -
15 R43928 1 Adapter, Turbo Oil Supply -
16 11-31012 1 Gasket -
19 27-09603 1 Tube Assembly -
20 21-09501 1 Male Elbow, 90° Steel M16 x 1.5 x 3/8- 37T -
25 15-00701 1 Flat Washer M8 -
26 21-09512 1 Female Adapter, Steel 3/4 O-ring port -
27 21-00032 1 Male Elbow 900, Steel 3/4 O-ring port -
29 21-62600 1 Male Elbow, 900 Steel 5/8 O-ring port -
30 21-35003 1 Male Elbow, 900 Steel 5/8 O-ring port -
33 21-03459 1 Female Elbow 900 Steel, 5/8 O-ring port -
34 13-00814 4 Stud, M10 x 1.5 x 30 mm -
35 14-00817 4 Hex Nut, M10 x 1.5 S/S -
36 15-00804 4 Wave Washer, M10 -
37 11-15704 2 Gasket -
38 31-15703 2 Adapter, Turbo Coolant Port Connection -
39 12-11131 4 Capscrew, Flathead Socket M6 x 1.0 x 20 mm -
40 27-29602 1 Connector, Air Inlet -
41 16-25701 1 O-ring -
42 16-29501 1 O-ring -
43 00-29501 1 Clip, Air Inlet Tube Retainer -
44 15-99707 2 Wave Washer, M8 S/S -
46 23-29602 1 Bracket, Air Inlet Tube Retainer -
49 15-99131 2 Wave Washer M6 S/S -
P1066 12/18
2 - 15
M1066A1 @ 1800 RPM
A-10731 / C-5662
P1066 12/18
2 - 16
M1066A1 @ 1800 RPM

3 13-00814 4 Stud, M10 x 1.5 x 30 mm -
4 14-00817 4 Hex Nut, M10 x 1.5 S/S -
5 15-00804 4 Wave Washer M10 -
14 16-01000 2 O-ring -
16 11-31012 1 Gasket -
21 51M7042 1 O-ring -
25 15-00701 1 Flat Washer M8 -
29 21-62600 1 Male Elbow, 900 Steel 5/8 O-ring port x 3/4- 37T -
34 13-00814 4 Stud, M10 x 1.5 x 30 mm -
35 14-00817 4 Hex Nut, M10 x 1.5 S/S -
36 15-00804 4 Wave Washer, M10 -
37 11-15704 2 Gasket -
39 31-19601 1 Adapter, Turbo Coolant Inlet -
40 12-11131 4 Capscrew, Flathead Socket M6 x 1.0 x 20 mm (Grade 10.9) -
42 16-25701 1 O-ring -
43 16-29501 1 O-ring -
46 15-99707 1 Wave Washer, M8 S/S -
47 23-29602 1 Bracket, Air Inlet Tube Retainer -
50 15-99131 2 Wave Washer M6 S/S -
P1066 12/18
2 - 17
M1066A2 @ 1800
A-10700 / C-5970
P1066 12/18
2 - 18
M1066A2 @ 1800

3 13-00814 4 Stud, M10 x 1.5 x 30 mm -
4 14-00817 4 Hex Nut, M10 x 1.5 S/S -
5 15-00804 4 Wave Washer M10 -
12 27-31402 1 Tube, Turbo Oil Return (Lower) -
14 16-01000 2 O-ring -
16 11-31012 1 Gasket -
21 51M7042 1 O-ring -
25 15-00701 1 Flat Washer M8 -
30 21-14817 1 Male Elbow, 900 Steel M22 x 1.5 x 3/4- 37T -
34 13-00814 4 Stud, M10 x 1.5 x 30 mm -
35 14-00817 4 Hex Nut, M10 x 1.5 S/S -
36 15-00804 4 Wave Washer, M10 -
37 11-15704 1 Gasket -
39 12-11131 2 Capscrew, Flathead Socket M6 x 1.0 x 20 mm (Grade 10.9) -
41 16-25701 1 O-ring -
42 16-29601 1 O-ring -
45 15-99707 1 Wave Washer M8 S/S -
46 19-29601 1 V-clamp -
P1066 12/18
2 - 19
Updated 7-27-16
M1066A, M1066A1 & A2 @1500 RPM
A-11007 / C-5550
P1066 12/18
2 - 20
Updated 7-27-16
M1066A, M1066A1 & A2 @1500 RPM
1 30-31426-1 1 Turbocharger, K26 (see parts detail) Data Plate # 5326 988 6493 M1066A1 & A2 -
30-21400-1 1 Turbocharger, K26 (see parts detail) Data Plate # 5326 988 6090 M1066A -
3 13-00814 4 Stud, M10 x 1.5 x 30 mm -
4 14-00817 4 Hex Nut, M10 x 1.5 S/S -
5 15-00804 4 Wave Washer M10 -
14 16-01000 1 O-ring -
16 11-31012 1 Gasket -
20 21-09501 1 Male Elbow, 90° Steel M16 x 1.5 x 3/8-37T -
21 51M7042 1 O-ring -
25 15-00701 1 Flat Washer M8 -
27 15-09501 1 Sealing Washer -
30 16-25701 1 O-ring -
31 18-21017 1 Hose, 2" ID x 3" 4 Ply Silicone -
35 15-99707 1 Wave Washer M8 S/S -
P1066 12/18
2 - 21
M1066A3 @ 1800
A-11036 / C-5971
P1066 12/18
2 - 22
M1066A3 @ 1800

3 13-00814 4 Stud, M10 x 1.5 x 30 mm -
4 14-00817 4 Hex Nut, M10 x 1.5 S/S -
5 15-00804 4 Wave Washer M10 -
14 16-01000 2 O-ring -
16 11-31012 1 Gasket -
21 51M7042 1 O-ring -
25 15-00701 1 Flat Washer M8 -
34 13-00814 4 Stud, M10 x 1.5 x 30 mm -
35 14-00817 4 Hex Nut, M10 x 1.5 S/S -
36 15-00804 4 Wave Washer, M10 -
37 11-15704 2 Gasket -
42 16-25701 1 O-ring -
47 15-99707 1 Wave Washer, M8 S/S -
P1066 12/18
2 - 23
Updated 6-18-09
L1066H & M1066H
A-10158/ C-5965a
P1066 12/18
2 - 24

L1066H & M1066H
1 10-29601 1 Manifold, Intake and Aftercooler -
2 R515030 1 Gasket -
4 20-29601-1 1 Element, Intake Aftercooler -
5 16-09601 2 O-ring -
7 19M7865 40 Capscrew, Hex Head Flanged M8 x 1.25 x 16 mm (Grade 10.9) -
10 15-00706 4 Flat Washer M8 S/S -
13 16-09504 2 O-ring -
16 19M7866 13 Capscrew, Hex Head Flanged, M8 x 1.25 x 20 mm (Grade 10.9) -
19 27-09501 1 Connector, Raw Water Pump Outlet -
20 27-09502 1 Connector, Aftercooler Outlet -
21 16-13101 2 O-ring -
22 21-00027 ** Plug, Socket Head Brass 1/8 NPT -
25 19-01032 6 Hose Clamp #32 -
26 27-19510 1 Tube, Heat Exchanger Inlet -
27 00-29601 1 Heat Shield, Aftercooler -
28 12-99757 11 Capscrew, Button Head Socket M8 x 1.25 x 16 mm S/S -
29 15-99707 11 Wave Washer M8 S/S -
31 21-29504 1 Drain, Aftercooler Condensate S/S -
32 13-85001 2 Stud, M10 x 1.5 x 45 mm (57 mm LOA Grade 8.8) -
33 14-80811 2 Hex Nut, Flanged M10 -
34 21-09516 1 Male Connector S/S 3/8- 37T x 3/8 O-R Port -
35 27-29605 1 Tube Assembly, Aftercooler Condensate -
36 19-72252 1 Adelle Clamp -
37 21-17302 1 Spacer, Steel -
**As required
P1066 12/18
2 - 25
L1066H
A-10159 / C-5972
P1066 12/18
2 - 26

L1066H

3 13-00814 4 Stud, M10 x 1.5 x 30 mm -
4 14-00817 4 Hex Nut, M10 x 1.5 S/S -
5 15-00804 4 Wave Washer M10 -
14 16-01000 2 O-ring -
16 11-31012 1 Gasket -
25 15-00701 1 Flat Washer M8 -
30 21-14817 1 Male Elbow, 900 Steel M22 x 1.5 x 3/4- 37T -
34 13-00814 4 Stud, M10 x 1.5 x 30 mm -
35 14-00817 4 Hex Nut, M10 x 1.5 S/S -
36 15-00804 4 Wave Washer, M10 -
37 11-15704 1 Gasket -
41 16-25701 1 O-ring -
42 16-29601 1 O-ring -
45 15-99707 1 Wave Washer, M8 S/S -
46 19-29601 1 V-clamp -
47 51M7042 1 O-ring -
P1066 12/18
2 - 27

M1066H
A-10372/ C-5591
P1066 12/18
2 - 28

M1066H
2 11-31615 1 Gasket, Turbo/ Exhaust Mounting -
3 13-00814 4 Stud, M10 x 1.5 x 30 mm -
4 14-00818 4 Hex Nut M10 x 1.5 S/S -
5 15-00804 4 Wave Washer M10 -
7 27-31602 1 Tube, Turbo Oil Return -
12 27-39504 1 Tube, Turbo Oil Return -
14 16-01000 2 O-ring -
16 11-31012 1 Gasket -
19 27-09601 1 Tube Assembly, Turbo Oil Supply
20 21-09501 1 Male Elbow 90° Steel, M16 x 1.5 x 3/8-37T -
22 19-72252 1 Adelle Clamp, 3/8" ID x 3/8" Stud -
25 15-00701 1 Flat Washer M8 -
26 21-09512 1 Female Adapter Steel 3/4" NPT x 1-1/4 O-ring Port -
27 21-00032 1 Male Elbow 90° Steel 3/4" O-ring Port x 3/4-37T -
29 21-62600 1 Male Elbow 90° Steel 5/8 O-ring Port x 3/4-37T -
30 21-35003 1 Male Elbow 90° Steel 5/8 O-ring Port x 3/4-37T -
33 21-03459 1 Female Elbow 90° Steel 5/8 O-ring Port -
34 13-00814 4 Stud, M10 x 1.5 x 30 mm (42 mm LOA, Grade 8.8) -
35 14-00817 4 Hex Nut M10 x 1.5 S/S -
36 15-00804 4 Wave Washer M10 -
37 11-15704 2 Gasket, Block-off/ Adapter Mounting -
38 31-15703 1 Adapter, Turbo Coolant Port Connector -
40 12-11131 4 Capscrew, Flat head Socket M6 x 1.0 x 20 mm Grade 10.9 -
41 27-29402 1 Air Inlet Connector -
42 16-25701 1 O-ring -
48 51M7042 1 O-ring -
P1066 12/18
2 - 29
Air Filter
NL1066T
Reproduced by permission of Deere & Co., c2006. Deere & Company. All rights reserved. RGP11572z

1 AT225535 1 Air Filter Assembly (includes keys 5 & 10-12) -
2 AR64937 2 Band, Air Filter Mtg. -
3 R128438 1 Hose, Air Intake -
4 AT175358 1 Rain Hood -
5 R48568 1 Drain Valve, Rubber -
6 AT56657 1 Hose Clamp -
7 AT50923 1 Hose Clamp -
8 19M7785 4 Capscrew, Flange Head M10 x 1.5 x 25 mm -
9 14-80811 4 Hex Nut M10 x 1.5 -
10 AT225338 1 Air Filter Element - Outer (Primary) -
11 AT225339 1 Air Filter Element - Inner (Secondary) -
12 AT178515 1 Cover -
P1066 12/18
2 - 30
Air Filter
NL1066H1, H2
RGP11572

1 AT225535 1 Air Filter Assembly (includes keys #19- 22) -
2 RE519630 1 Bracket -
4 R517432 1 Plate -
5 R517431 1 Brace -
6 AR64937 2 Band, Air Filter Mtg. -
7 H76357 1 Hose 900 -
8 R517439 2 Tube 4" O.D. -
9 H88782 2 Hose 900 4" I.D. -
10 TY22475 5 Hose Clamp #80 -
11 TY22473 1 Hose Clamp #52 -
16 21M7442 1 Screw -
18 AT175358 1 Rain Hood -
19 AT225338 1 Element, Primary -
20 AT225339 1 Element, Secondary -
21 AT178515 1 Cover -
22 R48568 1 Valve -
P1066 12/18
2 - 31
Air Filter
NL1066H3

1 F301161 1 Air Filter Assembly -
4 R517432 1 Plate -
5 R517431 1 Brace -
6 AT136715 2 Band, Air Filter Mtg. -
7 R132527 1 Hose - Reducing 90, 5" I.D. x 4" I.D. -
8 R517439 2 Tube 4" O.D. -
9 H88782 1 Hose 900 4" I.D. -
10 TY22475 5 Hose Clamp #80 -
12 TY22492 1 Hose Clamp -
17 21M7442 1 Screw -
18 RE11158 1 Rain Cap -
19 AT175223 1 Filter Element, Primary -
20 AT175224 1 Filter Element, Secondary -
21 AT175222 1 Cover -
22 T158495 1 Valve -
23 T161929 1 O-ring -
P1066 12/18
2 - 32
Air Filter
NL1066H4
RGP11571

1 F301161 1 Air Filter Assembly (includes keys 19- 22) -
4 R517425 1 Plate -
5 R517424 1 Brace -
6 AT136715 2 Band, Air Filter Mtg. -
7 H88782 2 Hose - 900 4" I.D. -
8 R517439 2 Tube 4" O.D. -
9 R132527 1 Hose, Reducing 900 5" I.D. x 4" I.D. -
10 TY22475 5 Hose Clamp #80 -
11 TY22492 1 Hose Clamp -
17 RE11158 1 Rain Cap -
18 AT175223 1 Filter Element, Primary -
19 AT175224 1 Filter Element, Secondary -
20 AT175222 1 Cover -
21 T161929 1 O-ring -
22 T158495 1 Valve -
P1066 12/18
2 - 33
Air Intake
NL1066A1, A2, A3
RGP11371

1 RE518655 1 Intake Manifold (also order key #3) -
2 19M8528 2 Screw, M10 x 55 mm -
3 R81275 2 Gasket -
4 R501472 1 Spacer (also order key #3) -
5 51M7039 1 O-ring -
6 RE60071 1 Fitting -
7 51M7041 1 O-ring -
8 RE46684 1 Plug -
9 19M7785 1 Screw -
10 R500596 1 Hose -
11 R110531 2 Clamp -
P1066 12/18
2 - 34
Air Intake
NL1066H1, H2, H3
RGP7801

1 RE508742 1 Air Intake -
2 19M8292 2 Capscrew, M10 x 50 mm -
3 R81275 1 Gasket -
4 R501472 1 Spacer -
5 R81275 1 Gasket -
6 51M7039 1 O-ring -
8 51M7041 1 O-ring -
9 RE46684 1 Plug -
P1066 12/18
2 - 35
Air Intake
NL1066H
Reproduced by permission of Deere & Co., c2006. Deere & Company. All rights reserved. RE516480PCDD01

1 R505166 1 Air Intake -
2 R500394 2 Screw -
3 R515030 1 Gasket -
4 RE46684 2 Plug -
5 R515029 1 Intake Manifold -
6 19M7785 10 Capscrew, M10 x 25 mm -
7 R104592 1 Pipe Plug -
8 19M7812 2 Capscrew, M10 x 100 mm -
9 R81275 1 Gasket -
P1066 12/18
2 - 36
Updated 9/25/17
Exhaust Manifold - Marine Application
A-8397/ C-2632

1 10-39602 1 Exhaust Manifold Assembly w/ Dry Flange* -
10-39603 1 Exhaust Manifold Assembly w/ Wet Flange* -
2 27-11012 1 Coolant Connector -
3 16-31001 1 O-ring -
4 11-39501 1 Gasket -
5 13-34801 12 Stud, M10 x 1.5 x 35 mm -
6 13-05001 2 Stud, M10 x 1.5 x 25 mm -
7 15-00300 14 Washer (special) -
8 14-00810 14 Hex Nut M10 x 1.5 -
9 11-31001 6 Gasket *** -
10 17-10005 ** Expansion Plug, 2-1/8" -
11 17-10001 ** Expansion Plug, 1-5/8" -
12 21-12502 ** Plug -
* See Exhaust Manifold & Adapter Detail for components

** As required
*** NOTE: This gasket requires the mounting fasteners to be
retorqued once engine has cooled down after one
hour of engine operation.
P1066 12/18
2 - 37
Updated 9/25/17
Exhaust Manifold - Marine Application 4 Valve
A-10068/ C-5643cyl6

1 10-39602 1 Exhaust Manifold Assembly w/ Dry Flange* -
2 27-19509 1 Coolant Connector -
3 16-31001 2 O-ring -
4 11-39502 1 Gasket -
5 13-00816 12 Stud, M10 x 1.5 x 50 mm -
6 01437-01025 3 Capscrew 12 Pt. M10 x 1.5 x 25 mm -
7 15-00300 15 Flat Washer (special) -
8 14-00810 12 Hex Nut M10 x 1.5 -
9 11-31001 12 Gasket, Exhaust (previous # 11-31011) ** -
11 28-39501 6 Spacer Plate, Exhaust Manifold Mounting -
12 31-19501 1 Adapter, Coolant Connector -
13 RE516027 1 Tube (includes key #14 - marked R504755) -
14 R63185 2 O-ring -
15 R504754 1 Manifold -
16 R505480 1 Gasket -
17 19M7785 2 Screw -
** NOTE: This gasket requires the mounting fasteners to be

retorqued once engine has cooled down after one
hour of engine operation.
P1066 12/18
2 - 38
Exhaust Manifold and Adapter - Marine Application
A4653, A4654,
A4655/ C-2648

1 10-39601 1 Exhaust Manifold -
2 10-31513 1 Dry Exhaust Flange Adapter -
10-31506 1 Wet Exhaust Flange for Turbo Mounting -
3 11-30013 1 Gasket -
4 12-00414 4 Capscrew, Hex Head, 7/16-14 x 1-1/2 -
5 15-00402 4 Lock Washer, 7/16 -
6 21-10001 1 Drain Cock, 1/8 NPT -
Exhaust Manifold NL1066 all
RGP6517

1 R132262 1 Exhaust Manifold -
2 R90658 6 Gasket -
3 19M7810 12 Screw, M10 x 80 -

P1066 12/18
2 - 39
3" Dry Exhaust Elbow
M1066T 1o and 3o, M99C2, M1066A1-A2 @ 1500 RPM
A-6337/ B-4638

1 19-31401 1 V-Clamp -
2 21-31002 1 Plug, Square Head Brass 3/8 NPT -
3 27-31407 1 Dry Exhaust Elbow 3" (with 4" Flange - Standard) -
27-39502 1 Dry Exhaust Elbow - Sound Enclosure Applications (M1066T 3o) -
27-39614 1 Dry Exhaust Elbow - Sound Enclosure Applications (M1066T 1o and
M1066A1-A2 @1500 RPM)
4 12-00916 8 Capscrew, Hex Head, 5/8-11 x 2" -
5 15-00902 8 Lock Washer, Helical 5/8 -
6 14-00911 8 Hex Nut 5/8-11 -
7 11-31099 1 Gasket -
P1066 12/18
2 - 40
4" Dry Exhaust Elbow
L1066T- A- H All, M1066A1- A2 @1800 RPM, and M1066A3- H
A-1102C/ B-2614B

1 27-32511 1 Dry Exhaust Elbow 4" - Standard -
27-39604 1 Dry Exhaust Elbow - Sound Enclosure Applications -
2 21-31002 1 Plug, Square Head Brass 3/8 NPT -
3 11-31635 1 Gasket -
4 13-00814 4 Stud, M10 x 1.5 x 30 mm -
5 15-00804 4 Wave Washer, M10 -
6 14-00817 4 Hex Nut, Stainless Steel, M10 x 1.5 mm -
7 11-31099 1 Gasket -
8 12-00916 8 Capscrew, Hex Head 5/8-11 x 2.0" -
10 14-00911 8 Hex Nut, 5/8-11 -
P1066 12/18
2 - 41
4" & 5" Wet Exhaust Elbow (Heat Exchanged Units)
M1066T, M99C2, M1066A1- A2 @1500
A-10403, A-8514, A-8512/ B-8609
P1066 12/18
2 - 42
4" & 5" Wet Exhaust Elbow (Heat Exchanged Units)
M1066T, M99C2, M1066A1- A2 @1500
KEY PART NUMBER QTY. DESCRIPTION SERIAL NUMBER
1 27-31412 1 Elbow, Wet Exhaust 4" Cast Iron (M1066T & M1066A1) -
27-39509 1 Elbow, Wet Exhaust 4" S/S (optional on M1066T & M1066A1) -
27-30047 1 Elbow, Wet Exhaust 5" S/S (M1066A2) -
2 19-31401 1 V-Clamp -
3 21-31007 1 Male Elbow, 90° Copper 1" NPTx 1-1/4" HB (M1066T) -
21-31005 1 Male Elbow, 90° Copper 1" NPT x 1-5/8" HB (M1066A1) -
21-31015 1 Male Elbow, 900 Copper 1- 1/4" NPT x 1- 5/8" HB (M1066A2) -
4 41-01070 24" Hose, 1-1/4" ID, Wire Reinforced (M1066T) -
41-14801 36" Hose, 1-5/8" ID, Wire Reinforced (M1066A1- A2) -
5 19-00020 2 Hose Clamp, #20 (M1066T) -
19-00028 2 Hose Clamp, #28 (M1066A1- A2) -
6 27-19601 1 Tube, Raw Water Discharge (M1066T)* -
27-19503 1 Tube, Raw Water Discharge (M1066T with flow switch) -
27-19606 1 Tube, Raw Water Discharge (M1066A1)* -
7 18-19501 1 Hose, 1-1/4" ID x 2-1/2" 3 Ply Silicone (M1066T) -
18-26002 1 Hose, 2" ID x 2-3/4" 4 Ply Silicone (M1066A1- A2) -
8 19-01020 2 Hose Clamp, #20 Extended Band S/S (M1066T) -
19-01032 2 Hose Clamp, #32 Extended Band S/S (M1066A1- A2) -
9 23-19503 1 Bracket, Tube Support (M1066T) -
23-19510 1 Bracket, Tube Support (M1066A1- A2) -
10 19-00016 1 Hose Clamp #16 (M1066T) -
19-00020 1 Hose Clamp #20 (M1066A1- A2) -
*Not used on applications with the Raw Water Flow Switch
P1066 12/18
2 - 43
5" Wet Exhaust Elbow (Heat Exchanged Units)
M1066A1- A2 @1800 RPM, M1066A3 - H, All
A-10404/ B-8609z

1 27-30048 1 Wet Exhaust Elbow 5" S/S -
2 13-00814 4 Stud, M10 x 1.5 x 30 mm -
3 11-31635 1 Gasket, Turbo Exhaust (K27) -
4 14-00817 4 Hex Nut, M10 x 1.5 S/S -
5 15-00804 4 Wave Washer M10 -
6 21-31015 1 Male Elbow, 900 Copper, 1-1/4 NPT x 1- 5/8" HB -
7 41-14801 32 Hose, 1-5/8" I.D. Wire Reinforced -
8 19-00024 2 Hose Clamp #24 -
9 27-19606 1 Tube, Raw Water Discharge S/S -
12 23-19507 1 Bracket, Tube Support -
13 19-00028 1 Hose Clamp #28 -
P1066 12/18
2 - 44
5" Wet Exhaust Elbow (Heat Exchanged Units)
L1066
A-10814, A-3014/ C-1866

1 27-30048 1 Wet Exhaust Elbow 5" S/S (supercedes 27-31605 & 27-30031) -
2 13-00814 4 Stud, M10 x 1.5 x 30 mm -
3 11-31635 1 Gasket -
4 14-00817 4 Hex Nut M10 x 1.5 Stainless Steel -
5 15-00804 4 Wavewasher M10 -
6 21-31008 1 Male Elbow 900 Copper 1-1/4" NPT x 1-1/4" HB (L1066T) -
21-19503 1 Male Elbow 900 Copper 1-1/4" NPT x 1-3/4" HB (L1066A- H) -
7 41-01070 32" Hose 1- 1/4" I.D. Wire Reinforced (L1066T) -
41-01092 36" Hose 1- 3/4" I.D. Wire Reinforced (L1066A- H) -
8 19-00016 2 Hose Clamp #16 (L1066T) -
19-00032 2 Hose Clamp #32 (L1066A- H) -
P1066 12/18
2 - 45
Turbocharger
NL1066T, H1, H2, H3
RGP6264
KEY PART NUMBER QTY DESCRIPTION S/N

1 RE509809 1 Turbocharger (NL1066T, NL1066H1, remanufactured, marked RE509807) -
RE516654 1 Turbocharger (NL1066H2, remanufactured, marked RE516653) -
RE516661 1 Turbocharger (NL1066H3, remanufactured, marked RE516660) -
2 R123572 1 Gasket -
3 19M8162 4 Screw, M10 x 40 -
4 14M7296 4 Flange Nut, M10 -
5 M87733 2 Fitting -
6 R63548 2 O-ring -
7 RE503212 1 Hose Assembly, Turbo Oil Supply -
8 T77613 1 O-ring -
9 38H5154 1 Fitting -
10 51M7042 2 O-ring -
11 RE59438 1 Tube, Turbo Oil Return -
12 R123570 1 Gasket -
13 19M7866 2 Screw -
14 R115138 1 Hose -
15 RE65978 2 Clamp -
16 RE54885 1 Hose Fitting -
P1066 12/18
2 - 46
Turbocharger
NL1066H4
KEY PART NUMBER QTY DESCRIPTION SERIAL

NUMBER
1 RE516661 1 Turbocharger (NL1066H4, marked RE517239, remanufactured) -
2 19M8162 4 Capscrew, M10 x 40 mm -
3 M87733 1 Fitting -
4 R63548 1 O-ring -
5 14M7296 4 Flange Nut, M10 -
6 R123572 1 Gasket -
7 RE503212 1 Hose Assembly, Turbo Oil Supply -
8 T77613 1 O-ring -
9 38H5154 1 Fitting -
10 51M7042 2 O-ring -
11 19M7866 2 Screw -
12 RE54885 1 Hose Fitting -
13 RE65978 2 Clamp -
14 R115138 1 Hose -
15 RE515896 1 Tube, Turbo Oil Return -
P1066 12/18
2 - 47
Dry Exhaust Elbow
NL1066T, H1, H2, H3, H4
RGP6262
1 R123246 1 Exhaust Elbow -

2 R87732 1 Adapter -
3 RE40048 1 Clamp -
4 19M8162 4 Screw, M10 x 40 -
5 14M7296 4 Flange Nut, M10 -
P1066 12/18
2 - 48
Exhaust Adapter 4"
NL1066T, H1, H2, H3, H4
A-1088E, A-6861A/ B-1566B
1 31-31066 1 Exhaust Adapter 4" -

27-31009 1 Exhaust Flex S/S 4" x 18" -
2 AR43704 2 Clamp kit with fasteners (includes keys 3-5) -
3 14-00311 2 Hex Nut 3/8- 16 -
4 15-00321 4 Flat Washer 3/8" SAE -
6 12-00914 8 Capscrew, Hex Head 5/8- 11 x 1- 3/4" -
7 15-00902 8 Lock Washer Helical 5/8" -
8 14-00911 8 Hex Nut 5/8- 11 -
9 11-31099 1 Gasket -
P1066 12/18
2 - 49
K26 Turbocharger Assembly
Turbo
P1066 12/18
2 - 50
Updated 7-27-16

•• 30-31426-1 1 Turbocharger Assembly (ID Tag #5326 988 64 93 - includes all keys) -
•• 30-21400-1 1 Turbocharger Assembly (ID Tag #5326 988 60 90 - includes all keys) -
• 30-31430 1 Repair Kit (includes keys 4,5, 11-17, 19-22, 24, & 28) -
1 30-31662 1 Spacer Sleeve -
2 30-31401 1 Turbine Housing (10.0 for turbocharger 30-31426-1) -
30-31431 1 Turbine Housing (8.0 for turbocharger 30-21400-1) -
3 30-31433 1 Bearing Housing -
4 30-31434 2 Bushing -
5 30-31435 4 Snap Ring -
6 30-31436 1 Heat Shield -
7 30-31437 1 Shaft & Turbine Wheel Assembly -
8 30-31438 1 Thrust Ring -
9 30-31439 1 Flinger Sleeve -
10 30-21401 1 Compressor Wheel (for 30-21400 turbocharger) -
30-31440 1 Compressor Wheel (for 30-31426-1 turbocharger) -
11 30-31441 4 Piston Ring -
12 30-31442 1 Thrust Bearing -
13 30-31443 1 Oil Deflector -
14 30-31444 1 Backing Plate -
15 30-31445 4 Capscrew, Socket & Head, M6 x 1.0 x 16 mm Grade 10.9 -
16 30-39611 1 Lock Nut, M7 x 1 (Left hand) -
17 30-31447 1 O-ring -
18 30-21402 1 Compressor Housing (for 30-21400-1 turbocharger) -
30-31432 1 Compressor Housing (for 30-31426-1 turbocharger) -
19 30-31448 3 Clamp Plate (compressor side) -
20 30-39614 6 Capscrew, Socket Head M6 x 1.0 x 14 mm -
21 30-31450 3 Clamp Plate (turbine side) -
22 14-01131 6 Hex Nut M6 x 1.0 -
23 30-31452 6 Stud, M6 x 1.0 -
24 30-31453 4 Flat Washer, M6 -
25 13-00814 4 Stud, M10 x 1.5 x 30 mm -
26 30-31454 1 Name Plate -
27 30-31455 2 Rivet -
28 30-31428 1 O-ring -
29 30-31631 2 Plug, Socket Head, Steel M22 x 1.5 -
P1066 12/18
2 - 51
Turbo L
P1066 12/18
2 - 52

30-31627 1 Turbocharger Assembly (Includes all Keys 1-27) -
30-31630 1 Repair Kit (Includes Keys 3, 4, 6, 8, 9, 11, 12, 14, 15, 17, 22-27) -
1 30-31628 1 Turbine Housing -
2 30-31631 6 Plug, Socket Head, Steel, M22 x 1.5 -
3 30-31445 4 Cap Screw, Socket Head, M6 x 1.0 x 16 mm Grade 10.9 -
4 30-31453 4 Flat Washer, M6 -
5 30-31633 1 Bearing Housing -
6 30-31434 2 Bushing -
7 30-31637 1 Shaft & Turbine Wheel Assembly -
8 30-31441 4 Piston Ring -
9 30-31442 1 Thrust Bearing -
10 30-31438 1 Thrust Ring -
11 30-31443 1 Oil Deflector -
12 30-31439 1 Flinger Sleeve -
13 30-31643 1 Backing Plate -
14 30-31644 1 O-ring -
15 30-31435 4 Snap Ring -
16 30-31646 1 Compressor Wheel -
17 30-31446 1 Lock Nut -
18 30-31454 1 Name Plate -
19 30-31649 2 Screw, Self Tapping -
20 30-31659 1 Heat Shield -
21 30-31629 1 Compressor Housing -
22 12-00030 8 Cap Screw, Hex Head, M6 x 1.0 x 16 mm -
23 30-31657 4 Clamp Plate -
24 30-31654 3 Clamp Plate -
25 30-31655 6 Bolt -
26 30-31428 1 O-ring -
27 30-31662 1 Spacer Sleeve -
28 13-00814 4 Stud, M10 x 1.5 x 30 mm -
P1066 12/18
2 - 53
GROUP 3 - COOLING SYSTEM
Expansion Tank Assembly

L- M1066T- A , M99C2, and M1066HA1, A2, A3
A-8340A/ C-5005
P1066 12/18
3-0
Updated 12/18/18

L- M1066T- A, M99C2, and M1066HA1, A2, A3
1 10-19501 1 Expansion Tank Assembly (includes keys 7-17, & 44) -
2 10-11023 1 Filler Neck Assembly -
3 11-11022 1 Gasket -
4 12-20111 6 Capscrew, Socket Head, 1/4-20 x 3/4 -
5 15-00018 6 Lock Washer, High Collar, 1/4 -
6 21-19510 1 Filler Cap -
7 17-10001 4 Expansion Plug -
8 21-74801 1 Male Connector, Steel, 3/4 NPT x 5/8-37T -
9 12-00098 1 Capscrew, Hex Head 1/4-20 x 1/2" S/S -
10
11
15-19502
21-00530
1
**
Sealing Washer
Plug, Hex Head, Brass, 1/2 NPT
} Keel Cooled Only -
-
12 21-11003 ** Plug, Socket Head, Steel, 1/2 NPT -
13 21-11004 1 Plug, Socket Head, Steel, 3/4 NPT -
15 21-00136 1 Bushing, Brass, 1/2 NPT x 1/8 NPT -
16 21-72044 1 Street Elbow 90 Degrees, Brass, 1/8 NPT -
17 21-10001 1 Drain Cock, Brass, 1/8 NPT -
18 12-00313 6 Capscrew, Hex Head 3/8-16 x 1-1/4" -
20 11-11023 1 Gasket -
21 23-19502 1 Bracket -
24 12-00311 3 Capscrew, Hex Head, 3/8-16 x 3/4" -
25 15-00301 3 Flat Washer, 3/8" -
27 35-11000 1 Thermostat, 1800F/ 820C (formerly #35-10002) -
35-11007 1 Thermostat, 1900F/ 880C -
28 11-10015 2 Seal Ring -
29 35-11004 1 Clamp -
30 12-00223 2 Capscrew, Hex Head, 5/16-18 x 3/4" S/S -
31 15-00222 2 Lock Washer, Helical 5/16" S/S -
32 15-11000 2 Flat Washer, 5/16 USS S/S -
33 10-11024 1 Cover -
34 11-11013 1 Gasket -
35 12-00212 4 Capscrew, Hex Head 5/16-18 x 1" -
37 41-01013 30" Hose, 5/16" I.D., Polyvinyl -
38 00-71000 1 Nameplate "Lugger" -
00-00006 1 Nameplate "Northern Lights" -
}
39 10-11006 1 Keel Cooling Outlet -
40 11-11043 1 Gasket -
(L- M1066T Keel Cooled only)
41 15-00302 3 Lock Washer, 3/8 -
43 21-00027 ** Plug, Socket Head, Brass 1/8 NPT -
44 21-51901 ** Plug, Socket Head, Brass 1/4 NPT -
**As required
P1066 12/18
3-1
L- M1066H
A-10160/ C-5005z
P1066 12/18
3-2
Updated 11/7/19
L- M1066H

1 10-19501 1 Expansion Tank Assembly (includes 7-17) -
2 10-11023 1 Filler Neck Assembly -
3 11-11022 1 Gasket -
4 12-20111 6 Capscrew, Socket Head, 1/4-20 x 3/4 -
5 15-00018 6 Lock Washer, High Collar, 1/4 -
6 21-10007 1 Filler Cap -
7 17-10001 4 Expansion Plug -
9 21-00027 ** Plug, Socket Head, Brass 1/8 NPT (not shown) -
10 21-51901 ** Plug, Socket Head, Brass 1/4 NPT (not shown) -
15 21-00136 1 Bushing, Brass, 1/2 NPT x 1/8 NPT -
16 21-72044 1 Street Elbow 90 Degrees, Brass, 1/8 NPT -
17 21-10001 1 Drain Cock, Brass, 1/8 NPT -
20 11-11023 1 Gasket -
21 23-19506 1 Bracket -
24 12-00311 3 Capscrew, Hex Head, 3/8-16 x 3/4" -
25 15-00301 3 Flat Washer, 3/8" -
27 35-11000 1 Thermostat, 1800F/ 820C (formerly #35-10002) -
35-11007 1 Thermostat, 1900F/ 880C -
28 11-10015 2 Seal Ring -
29 35-11004 1 Clamp -
30 12-00223 2 Capscrew, Hex Head, 5/16-18 x 3/4" S/S -
32 15-11000 2 Flat Washer, 5/16 USS S/S -
33 10-11024 1 Cover -
34 11-11013 1 Gasket -
37 41-01013 30" Hose, 5/16" I.D., Polyvinyl -
00-71000 1 Nameplate "Lugger" -
39 21-13110 1 Spacer -
40 R123324 1 Clamp -
**As required
P1066 12/18
3-3
Heat Exchanger
L-M1066T, M99C2
A-8348/ C-4143
P1066 12/18
3-4
Heat Exchanger
L-M1066T, M99C2
1 20-19501 1 Heat Exchanger Assembly (Includes keys #18-24) -
2 11-11043 1 Gasket -
3 16-19502 1 O-ring -
4 12-00313 2 Capscrew, Hex Head, 3/8-16 x 1-1/4" -
7 13-00335 3 Stud, 3/8-16 x 3/8-24 x 1-1/4" -
8 15-70007 6 Snubbing Washer -
9 15-19504 3 Neoprene Washer -
10 14-00322 3 Hex Nut, Nylock 3/8-24 -
11 18-62520 1 Hose, 1-3/4" I.D. x 2-1/4" -
12 19-01028 2 Hose Clamp #28 -
13 27-11035 1 Tube, Coolant Pump Inlet -
14 21-00530 1 Plug, Hex Head, Brass, 1/2 NPT -
15 16-14804 1 O-ring -
18 20-19502 2 End Cover -
19 16-19501 2 O-ring -
20 12-09312 2 Capscrew, Hex Head, 3/8-16 x 1" S/S -
22 21-51905 ** Plug, Socket Head, 1" NPT -
23 21-10000 2 Zinc Plug -
24 21-10010 2 Zinc Electrode -
**As required
P1066 12/18
3-5
Heat Exchanger
L-M1066A- H and M1066A1, A2, A3, H
A-10162, A-10429/ C-5531
P1066 12/18
3-6
Heat Exchanger
L-M1066A- H and M1066A1, A2, A3, H

•• 20-19510 1 Heat Exchanger Assembly (includes keys #1-24) -
1 20-19504 1 Heat Exchanger -
2 11-11043 1 Gasket -
3 16-19502 1 O-ring -
7 13-00335 3 Stud, 3/8-16 x 3/8-24 x 1-1/4" -
8 15-70007 6 Snubbing Washer -
9 15-19504 3 Neoprene Washer -
10 14-00322 3 Hex Nut, Nylock 3/8-24 -
11 18-62520 1 Hose, 1-3/4" I.D. x 2-1/4" -
12 19-01028 2 Hose Clamp #28 -
13 27-19511 1 Tube, Coolant Pump Inlet (L- M1066H) -
27-19513 1 Tube, Coolant Pump Inlet (L1066A, M1066A1, A2, A3) -
14 21-00530 1 Plug, Hex Head, Brass, 1/2 NPT -
15 16-14804 1 O-ring -
18 20-19502 2 End Cover -
19 16-19501 2 O-ring -
20 12-09312 2 Capscrew, Hex Head, 3/8-16 x 1" S.S. -
22 21-51905 ** Plug, Socket Head, 1" NPT -
23 21-10000 2 Zinc Plug -
24 21-10010 2 Zinc Electrode -
**As required
P1066 12/18
3-7
Coolant Pump Inlet
Reproduced by permission of Deere & Co., c2006. Deere & Company. All rights reserved. RGP7821&6248

1 27-19506 1 Inlet Adapter, 2-1/4" Hose Barb (M1066 All & M99C2) -
27-19507 1 Inlet Adapter, 2-3/8" Hose Barb (L1066 All & M99C2) -
R121634 1 Inlet Adapter, 2" Hose Barb (NL1066 All & M99C2) -
2 16-14804 1 O-ring -
3 19M7867 2 Screw, M8 x 25 -
4 21-13101 ** Plug, 1/2" NPT -

**As required
For NL1066H1, H2, H3, and H4
5 R502983 1 Housing -
6 R89944 1 O-ring -
7 19M7867 1 Screw, M8 x 25 mm -
8 19M7802 1 Screw, M8 x 65 mm -
9 51M7043 1 O-ring -
10 RE46685 1 Plug -
P1066 12/18
3-8
updated 1-22-13
Coolant Pump
TP50847 & RGP6114


•• RE505980 1 Coolant Pump, Cast Iron (marked R503509, includes keys 1-11) -
• RE509813 1 Repair Kit (includes keys 1-2, 4-9 & 11) -
1 Impeller -
2 Seal* -
3 Housing* -
4 Ball Bearing* -
5 Ring* -
6 Shaft* -
7 A364R 1 Snap Ring -
8 51M7043 1 O-ring -
9 R123226 1 Gasket -
10 RE46685 1 Plug -
11 R100369 2 Filter -
12 19M7863 5 Capscrew, M6 x 25 -
13 19M7796 3 Capscrew, M6 x 30 -
14 R123417 1 Gasket -
15 R115250 1 Pulley, 93 mm OD -
16 19M7784 1 Capscrew, Flanged Head M6 x 1.0 x 12 mm -
17 RE508566 1 Timing Cover Insert Kit (not shown) -
*Not available separately - order Pump Repair Kit or Coolant Pump

Assembly
P1066 12/18
3-9
page updated 9-19-13
Raw Water Pump and Mounting
L- M1066T, M99C2
Tighten shaft nut to 75 lbs-ft

- Continue turning castle nut
as req'd to align next available
slot with hole in shaft for cotter
installation
A-8362/ C-4177

1 25-19501 1 Raw Water Pump (see Parts detail) -
2 R135101 1 Gear -
3 15-19503 1 Shaft Flat Washer -
4 14-19501 1 Hex Nut, Slotted -
5 32-00005 1 Cotter Pin -
6 16-19503 1 O-ring -
9 27-19502 1 Tube -
10 18-19501 2 Hose, 1-1/4" I.D. x 2- 1/2" -
11 19-01020 4 Hose Clamp #20 -
12 19-71031 1 Adelle Clamp -
15 15-00805 1 Flat Washer, M10 -
P1066 12/18
3 - 10
page updated 9-19-13
Raw Water Pump and Mounting
L1066A- H and M1066A1, A2, A3, H
Tighten shaft nut to 75 lbs-ft

- Continue turning castle nut
as req'd to align next available
slot with hole in shaft for cotter
installation
A-10161/ C-5450

1 25-19522 1 Raw Water Pump Assembly (See Parts Detail) -
2 R135101 1 Gear -
3 15-19503 1 Shaft Flat Washer -
4 14-19501 1 Hex Nut, Slotted -
5 32-00005 1 Cotter Pin -
6 16-19503 1 O-ring -
9 15-00007 2 Flat Washer M12 -
10 21-19504 1 Connector -
11 41-01112 3 Hose 2" I.D. Silicone -
12 19-01032 4 Hose Clamp, #32 Extended Band -
P1066 12/18
3 - 11
Raw Water Pump Assembly

25-19501 1 Raw Water Pump Assembly (Includes all keys) -
1 25-19502 1 Housing -
2 25-19503 1 Shaft -
3 25-11621 1 Cam -
4 25-11619 1 Screw -
5 25-19504 2 Bearing -
6 25-19506 2 Spacer -
7 25-19507 1 Seal, Lip Type -
8 25-19508 1 Seal, Mechanical/ Carbon -
9 25-19509 1 Support Washer -
10 25-19511 1 Wear Plate -
11 25-19512 1 Snap Ring -
12 25-11011 1 Impeller with Gasket -
13 25-11017 1 Gasket -
14 25-19513 1 Cover -
15 25-19514 6 Capscrew -
16 25-19516 1 Flange -
17 25-19517 1 O-ring -
P1066 12/18
3 - 12
updated 11-7-11
Raw Water Pump Assembly
A-10161/ D-4069

25-19522 1 Raw Water Pump Assembly (Includes all keys) -
1 25-19502 1 Housing -
2 31-09501 1 Adapter -
3 25-19521 1 Oil Seal -
4 25-15717 6 Capscrew, Socket Head M6 x 1.0 x 25 mm Stainless Steel -
5 15-00610 10 Lock Washer, M6 S/S -
6 25-15706 1 Wear Plate -
7 25-19524 1 Shaft -
8 25-15708 2 Bearing -
9 25-19526 1 Mechanical Seal -
10 25-15716 3 Snap Ring -
11 25-15713 1 O-ring -
12 25-15703 1 Cam -
13 25-15704 1 Impeller -
14 25-15711 1 O-ring -
15 25-19523 1 End Cover -
18 25-15714 1 O-ring -
P1066 12/18
3 - 13
Updated 12/18/18
Thermostat Housing Assembly

14
M1066TMCA 14
14 20
12
10 9
19
11
18
7
17
16
6 3
4
3
4
13 3
13
10-19400_drawing
Exhaust Manifold
P1066 12/18
3 - 14
Added 4-4-14
M1066T

1 31-19512 1 Adapter, Thermostat Housing -
2 11-11023 1 Gasket, Manifold to Expansion Tank -
3 12-00313 6 Capscrew, Hex Head 3/8"-16 X 1-1/4" -
4 15-00302 6 Lock Washer, Helical 3/8" -
5 15-00321 3 Flat Washer 3/8" SAE -
6 R116205 1 Gasket -
7 10-19503 1 Thermostat Housing -
8 21-13101 1 Plug Socket Head 1/2 NPT -
9 RE33705 1 Thermostat 180F/82C -
10 AR102258 1 Thermostat -
11 R133142 1 Gasket -
12 10-19506 1 Thermostat Cover, Vertical Outlet -
13 13-00832 3 Stud M10 x 1.5 x 125mm LOA -
14 14-80811 3 Hex Nut, Flanged -
15 21-00132 1 Bushing 1/4 NPT x 1/8 NPT -
o
17 21-10001 1 Drain Cock -
18 21-64803 1 M.Elbow 90, Stl. -
20 15-00300 3 Flat Washer M10 Small OD -
P1066 12/18
3 - 15
NL1066T, H1, H2, H3

1 R501556 1 Cover -
2 51M7041 2 O-ring -
3 RE46684 ** Plug -
4 15H624 ** Pipe Plug 1/2" -
5 19M7786 1 Capscrew, M10 x 30 -
6 R123629 1 Tube -
7 19M7788 1 Screw, M12 x 25 -
8 R123323 1 Clamp, Cylinder Head -
9 R123324 1 Clamp, Timing Gear Cover -
10 R123226 1 Seal -
11 R502814 1 Gasket -
12 19M7809 1 Screw, M10 x 70 -
13 RE522076 1 Thermostat 180°F/ 82°C (formerly #RE506300) -
**As required
P1066 12/18
3 - 16
Notes
P1066 12/18
3 - 17
NL1066H4
Reproduced by permission of Deere & Co., c2006. Deere & Company. All rights reserved. RE516361SPA,RGP8981
P1066 12/18
3 - 18
NL1066H4

1 R505480 1 Gasket -
2 ** Capscrew -
3 R504754 1 Manifold -
4 R63185 2 O-ring -
5 RE516027 1 Tube -
6 RE46684 ** Plug (includes key #17) -
7 19M7810 2 Capscrew, M10 x 80 -
8 CD16284 1 Plug -
9 RE517057 1 Housing (marked R515580) -
10 R505479 1 Gasket -
11 R123226 1 Seal -
12 R123324 1 Clamp -
13 R504854 1 Tube -
14 R515581 1 Cover, M8 x 45 -
15 R124607 1 Gasket -
16 19M7785 1 Capscrew, M10 x 25 -
17 51M7041 ** O-ring -
18 AR48675 1 Thermostat, 180°F (82°C) -
RE33705 1 Thermostat, 180°F (82°C) -
**As required
P1066 12/18
3 - 19
Engine Oil Cooler

L-M-NL1066T, M99C2, L1066A, M1066A1 @ 1800 RPM, NL1066H1
RGP8307

1 RE56690 1 Oil Cooler Element -
2 RE67231 1 Screw, M6 x 16 -
3 R123501 1 Gasket -
4 T122075 2 O-ring -
5 R123471 1 Housing -
6 51M7043 1 O-ring -
7 RE46686 1 Plug -
8 51M7040 1 O-ring -
9 RE46686 1 Plug -
10 R501428 1 Gasket -
11 R504734 1 O-ring -
12 R502811 1 Adapter -
13 19M7970 2 Screw, M8 x 100 -
14 RE67238 1 Screw, M8 x 20 -
15 19M7802 2 Screw, M8 x 65 -
P1066 12/18
3 - 20
Engine Oil Cooler
L1066A (Pleasure Craft Rating), M1066A1 @1500 RPM,

M1066A2, A3, H, NL1066H2, H3, H4

1 RE59298 1 Oil Cooler Element -
2 RE67231 1 Screw, M6 x 16 -
3 R123501 1 Gasket -
4 T122075 2 O-ring -
5 R123471 1 Housing -
6 RE46685 1 Plug -
7 RE46686 1 Plug -
8 R501428 1 Gasket -
9 R61105 2 O-ring -
10 R115252 1 Tube -
11 R135177 1 Adapter -
12 19M7970 2 Screw, M8 x 100 -
13 RE67238 1 Screw, M8 x 20 -
14 19M7802 2 Screw, M8 x 65 -
P1066 12/18
3 - 21
Idler Shaft Assembly
L- M1066T, M99C2
Reproduced by permission of Deere & Co., c2006. Deere & Company. All rights reserved. RGP6123 & RGP6278

1 RE500539 1 Idler Shaft (includes keys 2-4) -
2 H80753 1 Snap Ring -
3 1 Bearing* -
4 R500539 1 Hub -
5 19M7835 4 Capscrew, M10 x 35 mm -
6 R128660 1 Pulley, 168 mm O.D. -
7 19M7784 4 Screw -
*Not available separately - use RE500539

P1066 12/18
3 - 22
Idler Shaft Assembly & Fan Pulley
NL1066T
RGP9065

1 RE500538 1 Idler Shaft (includes keys #2-4) -
2 E1343FN 1 Snap Ring -
3 1 Shaft* -
4 1 Hub* -
6 R128658 1 Pulley, 140 mm O.D. -
*No longer available separately - order complete Idler Shaft assembly.
P1066 12/18
3 - 23
L1066A, M1066A1, A2, A3, NL1066H1, H2, H3
RGP9065

3 1 Shaft* -
4 1 Hub* -
6 R128660 1 Pulley, 168 mm O.D. (L1066A, M1066A1, A2, A3) -
R128662 1 Pulley, 203 mm O.D. (NL1066H1, H2, H3) -
P1066 12/18
3 - 24
L- M1066H, NL1066H4

3 1 Shaft* -
4 1 Hub* -
6 R128660 1 Pulley, 168 mm O.D. -
P1066 12/18
3 - 25
revised 4/8/10
Radiator & Mounting
M1066TMCA
A-11886/ D-4435
P1066 12/18
3 - 26
Radiator & Mounting
M1066TMCA
1 39-19606 1 Side Plate, Modular Radiator Guard Left hand -
2 39-19607 1 Side Plate, Modular Radiator Guard Right hand -
3 39-19608 1 Top Panel, Modular Radiator Guard -
4 20-12512 1 Radiator, Heresite Coated -
5 R132912 1 Fan Shroud -
6 20-19601 1 Air Duct Adapter -
7 12-09213 8 Capscrew, Hex Head 5/16- 18 x 1- 1/4" S/S -
9 15-11000 8 Flat Washer 5/16" USS S/S -
12 15-00706 22 Flat Washer, M8 S/S -
14 15-00805 12 Flat Washer M10 -
16 14-00811 6 Hex Nut, M10 x 1.5 -
17 AT34808 1 Fan 26" (Blower) -
18 R524736 1 Fan Spacer, 4 Bolt x 100 mm -
20 RE20971 1 Fan Guard -
21 12-09312 8 Capscrew, Hex Head 3/8- 16 x 1" S/S -
23 15-70006 8 Snubbing Washer S/S -
24 00-70079 1 Label "Northern Lights" -
25 18-12515 1 Hose, Radiator Inlet 2-1/2" I.D. -
26 19-00040 4 Hose Clamp #40 -
27 18-12516 1 Hose, Radiator Outlet 2" I.D. -
28 19-00032 2 Hose Clamp #32 -
29 19-00040 2 Hose Clamp #40 -
30 21-00135 1 Bushing, Brass 1/2 NPT x 1/4 NPT -
32 39-19611 1 Lower Valance -
P1066 12/18
3 - 27
revised 3/10/14
Radiator & Mounting
NL1066T
A-7615/ C-5778
P1066 12/18
3 - 28
revised 3/10/14
Radiator & Mounting
NL1066T
1 39-11015 2 Side Panel, Modular Radiator Guard -
2 39-11016 1 Top Panel, Modular Radiator Guard -
3 21-11001 2 Spacer Plate, Radiator Mtg. -
4 39-11017 1 Grille, Modular Radiator Guard -
5 RE64112 1 Radiator -
6 RE64114 1 Fan Shroud -
7 12-03310 4 Capscrew, Flh Skt 3/8- 16 x 3/4” -
8 12-00312 24 Capscrew, Hex Head 3/8- 16 x 1” -
9 15-00302 12 Lock Washer, Helical 3/8” -
10 15-00321 28 Flat Washer 3/8” Narrow -
11 15-00301 8 Flat Washer 3/8” Wide -
12 14-00312 12 Hex Nut, Nylock 3/8- 16 -
13 14-00301 4 U-Nut 3/8- 16 -
14 12-00212 6 Capscrew, Hex Head 5/16- 18 x 1” -
15 12-00209 2 Capscrew, Hex Head 5/16- 18 x 3/4” -
16 12-00213 4 Capscrew, Hex Head 5/16- 18 x 1 1/4” -
18 15-00221 8 Flat Washer 5/16” SAE -
19 15-00708 4 Stud Washer 8.4mm ID x 21mm OD x 4mm -
20 R128442 1 Fan Spacer 4 Bolt 49mm -
21 AT24834 1 Fan 23” (Blower) -
22 12-80049 4 Capscrew, Hex Head Flanged Socket, 10x1.5 x 80mm GR -
25 15-70004 4 Snubbing Washer S/S 0.25” ID x 0.84 -
26 19-00032 1 Hose Clamp #32 -
27 R128480 1 Hose, Radiator Outlet -
28 19-00036 1 Hose Clamp #36 -
29 19-00028 2 Hose Clamp #28 -
30 R128455 1 Hose, Radiator Inlet -
32 41-01013 1 Hose, Polyvinyl 5/16” ID x 7/16” OD -
33 RE64092 1 Cap, Coolant Fill 10 PSI -
34 00-70082 1 Label, “Northern Lights” 2’ x 22” -

P1066 12/18
3 - 29
Radiator & Mounting
NL1066H1-H2-H3
Reproduced by permission of Deere & Co., c2007. Deere & Company. All rights reserved. RE519147RGP01
P1066 12/18
3 - 30
Radiator & Mounting
NL1066H1-H2-H3
3 24M7178 8 Washer -
4 R517241 1 Spacer -
5 AT262316 1 Fan-Blower (28") -
6 19M9017 4 Screw, Flange -
7 19M8242 4 Screw -
8 RE519073 1 Shroud -
9 AH170895 2 Clamp Band, Constant Torque -
10 T162878 1 Hose, Silicone -
11 RE52702 6 Hose Clamp, Constant Tension Type -
12 R517238 1 Tube, Charge Air Cooler Inlet -
13 R517331 2 U-bolt -
14 T161983 1 Hose, Aftercooler -
15 R517228 1 Tube, Charge Air Cooler Outlet -
18 R517428 1 Support -
19 24M7024 4 Washer -
20 14M7396 4 Nut -
21 RE519072 1 Aftercooler -
24 RE519634 1 Bracket, Right Hand for Air Flow Tube Support -
25 TY22472 4 Hose Clamp #44 -
28 RE24897 1 Cap, Radiator w/ Cover -
29 RE519635 1 Bracket, Left Hand for Air Flow Tube Support -
31 39-19601 1 Side Panel, Left Hand -
32 39-19602 1 Side Panel, Right Hand -
33 39-19603 1 Top Panel -
34 39-19604 1 Grille -
35 R123451 1 Drive Belt, Poly-V 1605 mm (not shown) -
36 00-70082 1 Label, "Northern Lights" (not shown) -
P1066 12/18
3 - 31
Radiator & Mounting
NL1066H4
Reproduced by permission of Deere & Co., c2007. Deere & Company. All rights reserved. RE519147RGP01
P1066 12/18
3 - 32
Radiator & Mounting
NL1066H4
3 24M7178 8 Washer -
4 R517241 1 Spacer -
5 AT262316 1 Fan-Blower (28") -
6 19M9017 4 Screw, Flange -
7 19M8242 4 Screw -
8 RE519073 1 Shroud -
9 AH170895 2 Clamp Band, Constant Torque -
11 RE52702 6 Hose Clamp, Constant Tension Type -
12 R517238 1 Tube, Charge Air Cooler Inlet -
13 R517331 2 U-bolt -
14 T161983 2 Hose, Aftercooler -
15 R517239 1 Tube, Charge Air Cooler Outlet -
16 H152403 1 Hose - Intake (Reducer) -
18 R517428 1 Support -
19 24M7024 4 Washer -
20 14M7396 4 Nut -
21 RE519072 1 Aftercooler -
24 RE519634 1 Bracket, Right Hand for Air Flow Tube Support -
25 TY22472 4 Hose Clamp #44 -
28 RE24897 1 Cap, Radiator w/ Cover -
29 RE519635 1 Bracket, Left Hand for Air Flow Tube Support -
31 39-19601 1 Side Panel, Left Hand -
32 39-19602 1 Side Panel, Right Hand -
33 39-19603 1 Top Panel -
34 39-19604 1 Grille -
35 R123436 1 Drive Belt, Poly-V 1580 mm (not shown) -
36 00-70082 1 Label, "Northern Lights" (not shown) -
P1066 12/18
3 - 33
Updated 7-27-16
Fuel Injection System
L- M- NL1066T, M99C2, M1066A1 @ 1800 RPM - M1066A @ 1500 RPM - NL1066H1

DE10 System
P1066 12/18
4-0
Updated 8-8-16
L- M- NL1066T, M99C2, M1066A1 @ 1800 RPM - M1066A @ 1500 RPM - NL1066H1

DE10 System

1 RE518089 1 Injection Pump (marked RE518164) M1066T @1500 RPM up to xxxx-42303
RE518089 1 Injection Pump (marked RE518164) L-M-NL1066T, M99C@ @1800 RPM
RE518088 1 Injection Pump (marked RE518165) M1066T - A @1500 RPM from xxxx-42304
RE518088 1 Injection Pump (marked RE518165) M1066A1 @1800 RPM and

NL1066H1
2 14M7298 3 Flange Nut, No. 5 -
3 R116386 3 Stud -
4 RE515228 1 Fuel Line, No. 1 -
5 RE515229 1 Fuel Line, No. 2 -
6 RE515230 1 Fuel Line, No. 3 -
7 RE515231 1 Fuel Line, No. 4 -
8 RE515232 1 Fuel Line, No. 5 -
9 RE515233 1 Fuel Line, No. 6 -
10 RE19800 1 Clamp -
11 19M8560 1 Capscrew -
12 RE20901 1 Clamp -
13 19M6614 1 Capscrew -
14 19M6614 5 Capscrew, M6 x 12 -
15 RE19797 4 Clamp -
16 R502076 1 Back-up Ring -
17 R505472 1 Gear (60 Teeth) -
18 R132874 1 Washer -
19 R91360 1 Nut -
20 19M7640 4 Capscrew -
21 12H316 4 Lock Washer, No. 6 -
22 24M7027 4 Washer -
23 1 Engine Controller (see Application Chart)
24 14M7298 2 Flange Nut, M8 -
25 R503520 1 Bracket -
26 19M7784 1 Capscrew, M10 x 20 mm -
27 R92352 6 Packing -
28 RE531436 6 Fuel Injector (new, formerly #RE507766) -
SE501103 1 Fuel Injector (reconditioned) -
29 RE508716 6 Clamp -
30 R51936 ** Tube Seal -
31 16-59502 12 O-ring (2 ea. per injector) -
32 R531438 6 Tee Fitting -
33 RE68748 4 Tube Assembly (includes #30) -
34 AR85519 2 Plug -
35 R123593 2 Tube Nut -
36 RE521822 1 Temperature Sensor (Fuel) not shown -
37 RE521823 1 Pressure Sensor -
**As required
P1066 12/18
4-1
Updated 7-27-16
Fuel Injection System - Double Wall Fuel Lines
L- M1066T, M99C2, M1066A1 @ 1800 RPM - M1066A @ 1500 RPM

DE10 System
ST14555-2
P1066 12/18
4-2
Updated 7-27-16
L- M1066T, M99C2, M1066A1 @ 1800 RPM - M1066A @ 1500 RPM

DE10 System

1 27-59621 1 Injection Line #1 Double Wall -
7 27-59615 1 Tube, Fuel Return to Alarm Tank -
9 21-59504 5 Banjo Bolt, M8 x .75 x 16 mm -
10 21-59516 1 Banjo Bolt -
12 18-59508 1 Hose Assembly 1/4" I.D. x 600 mm S/S TFE -
13 21-55703 1 Compression Union, Steel 8 mm -
14 19-55701 4 Clamp Assembly 2 Lines -
17 10-50002 1 Alarm Tank Assembly -
18 21-50041 1 Reducing Union, Brass 3/16 x 5/16 -
19 23-59601 1 Bracket, Alarm Tank Mtg -
21 15-00701 2 Flat Washer M8 -
23 14-00711 2 Hex Nut M8 x 1.25 -
26 18-59509 1 Hose Assembly, 1/4" I.D. x 6 " S/S TFE -
P1066 12/18
4-3
L1066A, M1066A1 @1500 RPM, M1066A2- A3, NL1066H2- H3

VP44 System
RGP9059
P1066 12/18
4-4
L1066A, M1066A1 @1500 RPM, M1066A2- A3, NL1066H2- H3

VP44 System

1 RE506680 1 Injection Pump, 12 Volt (L1066A- M1066A1 @1500 RPM, M1066A2, -
NL1066H2)
RE522826 1 Injection Pump, 24 Volt (L1066A- M1066A1 @1500 RPM, M1066A2, -
NL1066H2)
RE515887 1 Injection Pump, 12 Volt (M1066A3- NL1066H3) -
RE515888 1 Injection Pump, 24 Volt (M1066A3- NL1066H3) -
2 R54873 1 O-ring -
3 R501039 1 Adapter -
4 T76938 1 O-ring -
5 R123295 1 O-ring -
6 R515150 1 Gear -
7 RE504798 4 Screw -
9 RE507653 1 Fuel Line, No. 1 -
10 RE507654 1 Fuel Line, No. 2 -
11 RE507655 1 Fuel Line, No. 3 -
12 RE507656 1 Fuel Line, No. 4 -
13 RE507657 1 Fuel Line, No. 5 -
14 RE507658 1 Fuel Line, No. 6 -
15 R51936 ** Sealing Washer -
16 RE68748 4 Tube (includes 2 of key #15) -
17 27-59613 1 Tube Assembly, Fuel Return
18 R123593 2 Tube Nut -
19 R116366 6 Screw -
21 R79605 6 Washer -
22 R79604 6 Tube Nut -
23 RE505079 6 Fuel Injector (M1066A3- NL1066H3) -
RE507948 6 Fuel Injector (L1066A- M1066A1 @1500 RPM, M1066A2- NL1066H2, -
formerly RE506688)
24 T27860 3 Washer -
25 AR85519 2 Plug -
26 19M7923 4 Capscrew, M6 x 12 -
27 RE19797 4 Clamp -
28 19M8560 1 Capscrew, M6 x 12 -
29 RE20901 1 Clamp -
30 19M7923 1 Capscrew, M6 x 12 -
31 RE19800 1 Clamp -
32 1 Engine Controller, 12V (See Application Chart) -
**As required
P1066 12/18
4-5
L1066A, M1066A1 @ 1500 RPM, and M1066A2, A3

VP44 System
ST14476-1
P1066 12/18
4-6

L1066A, M1066A1 @ 1500 RPM, and M1066A2, A3
VP44 System

9 21-59504 5 Banjo Bolt M8 x .75 x 16 mm -
10 21-59516 1 Banjo Bolt -
12 18-59508 1 Hose Assembly 1/4" I.D. x 600 mm S/S -
13 21-55703 1 Compression Union, Steel 8 mm -
15 21-50041 1 Reducing Union, Brass 3/16 x 5/16 -
16 19-59601 3 Clamp Assembly, 2 Lines -
19 23-59601 1 Bracket, Alarm Tank Mtg. -
21 15-00701 2 Flat Washer M8 -
23 14-00711 2 Hex Nut M8 x 1.25 -
26 18-59509 1 Hose Assembly, 1/4" I.D. x 6" S/S TFE -
P1066 12/18
4-7
Amended 7-1-08
L- M1066H, NL1066H4
RGP9102
P1066 12/18
4-8
Amended 11/7/11
L- M1066H, NL1066H4

1 RE507959 1 Fuel Injection Pump -
2 R516999 1 Screen -
3 RE516336 1 Sensor, Fuel Temperature -
5 R503307 4 Tube -
6 RE507541 2 Fuel Line, No. 5 & 6 -
7 RE507540 2 Fuel Line, No. 3 & 4 -
8 RE507539 2 Fuel Line, No. 1 & 2 -
9 19M8528 3 Capscrew, M10 x 55 mm, No. 3 -
11 RE507538 1 Fuel Line, No. 5 -
13 R134920 12 Nut -
14 19M7775 2 Capscrew, M6 x 16 mm -
15 R516125 1 O-ring -
17 R55453 1 O-ring -
18 R91360 1 Nut -
19 R502541 1 Gear, 30 Teeth -
20 R116031 1 O-ring -
21 R504577 1 Adapter -
22 14M7298 2 Flange Nut, M8 -
23 RE509093 1 Wiring Harness -
24 RE507537 1 Fuel Line -
25 R504239 1 Bracket -
26 RE507863 1 Fuel Manifold Assembly (includes keys 27- 28) -
27 RE520930 1 Sensor, Fuel Pressure (former #RE515635) -
28 RE515636 6 Restrictor -
29 R503308 6 Fitting -
30 R123593 14 Tube Nut -
31 R51936 14 Sealing Washer -
32 RE517370 1 Fitting Plug (not shown) -
33 RE519730 6 Fuel Injector -
34 RE516335 1 Relief Valve -
P1066 12/18
4-9
Double Wall Injection Lines and Alarm Tank
L- M1066H High Pressure Common Rail
A-10636/ ST14487-1
P1066 12/18
4 - 10
Double Wall Injection Lines and Alarm Tank
L- M1066H High Pressure Common Rail

1 27-59512 2 Injection Line #1 and #2 Double Wall -
4 27-59504 1 Tube Assembly, HPCR Manifold Inlet #1 -
5 27-59505 1 Tube Assembly, HPCR Manifold Supply #2 -
7 27-59507 1 Tube, Fuel Return to Alarm Tank, Low -
10 21-59517 5 Banjo Bolt -
11 15-59518 3 Banjo Bolt, Double Length -
12 15-55701 19 Banjo Washer -
13 18-59512 1 Hose Assembly, 1/4" I.D. x 12" S/S -
14 21-59514 1 Reducing Union, Steel 8 mm x 6 mm -
15 18-59513 1 Hose Assembly 1/4" I.D. x 13" S/S -
17 23-59601 1 Bracket, Alarm Tank Mtg. -
19 15-00701 2 Flat Washer M8 -
21 14-00711 2 Hex Nut M8 x 1.25 -
24 10-59601 1 Rear Cover, HPCR Manifold -
25 10-59602 1 Front Cover, HPCR Manifold -
29 15-09805 3 Flat Washer M10 S/S -
30 16-15006 1 O-ring -
31 21-59519 1 Elbow, 450 Swivel, Steel 3/8- 37T -
33 21-09702 1 Male Connector, Brass 1/4 NPT x 3/8" -
34 27-59637 1 Tube Assembly, Final Fuel Filter Outlet -
P1066 12/18
4 - 11
Amended 5-15-14
Engine Control Unit Applications
Propulsion Units - (Serial number must be provided when ordering)
L1066T DE10 System
26-9960112C135 135 Hp @ 2200 RPM 12 Volt

26-9960124C135 135 Hp @ 2200 RPM 24 Volt
26-9960112M165 165 Hp @ 2400 RPM 12 Volt
26-9960124M165 165 Hp @ 2400 RPM 24 Volt
26-9960112H170 170 Hp @ 2500 RPM 12 Volt
26-9960124H170 170 Hp @ 2500 RPM 24 Volt
L1066A VP44 System
26-9960212C185 185 Hp @ 2400 RPM 12 Volt

26-9960224C185 185 Hp @ 2400 RPM 24 Volt
26-9960212M200 200 Hp @ 2400 RPM 12 Volt
26-9960224M200 200 Hp @ 2400 RPM 24 Volt
26-9960212H225 225 Hp @ 2400 RPM 12 Volt
26-9960224H225 225 Hp @ 2400 RPM 24 Volt
26-9960212P250 250 Hp @ 2400 RPM 12 Volt
26-9960224P250 250 Hp @ 2400 RPM 24 Volt
L1066H High Pressure Common Rail
26-9960300C225 225 Hp @ 2200 RPM 12 or 24 Volt

26-9960300M250 250 Hp @ 2200 RPM 12 or 24 Volt
26-9960300H275 275 Hp @ 2400 RPM 12 or 24 Volt
P1066 12/18
4 - 12
Amended 7-27-16
Engine Control Unit Applications
Generator Units - (Serial number must be provided when ordering)
M1066T and C-series DE10 System
26-9960112699 99 kW @ 1800 RPM 12 Volt

26-9960124699 99 kW @ 1800 RPM 24 Volt
26-9960112580 80 kW @ 1500 RPM 12 Volt
26-9960124580 80 kW @ 1500 RPM 24 Volt
M1066A DE10 System
26-9960112599 99 kW @ 1500 RPM 12 Volt

26-9960124599 99 kW @ 1500 RPM 24 Volt
M1066A1 DE10 System
26-99601126130 130 kW @ 1800 RPM 12 Volt

26-99601246130 130 kW @ 1800 RPM 24 Volt
M1066A1 VP44 System
26-99602125105 105 kW @ 1500 RPM 12 Volt

26-99602245105 105 kW @ 1500 RPM 24 Volt
M1066A2 VP44 System
26-99602126145 145 kW @ 1800 RPM 12 Volt

26-99602246145 145 kW @ 1800 RPM 24 Volt
26-99602125115 115 kW @ 1500 RPM 12 Volt
26-99602245115 115 kW @ 1500 RPM 24 Volt
M1066A3 VP44 System
26-99602126160 160 kW @ 1800 RPM 12 Volt

26-99602246160 160 kW @ 1800 RPM 24 Volt
M1066H High Pressure Common Rail
26-99603006185 185 kW @ 1800 RPM 12 or 24 Volt

26-99603005155 155 kW @ 1500 RPM 12 or 24 Volt
P1066 12/18
4 - 13
Updated 7-27-16
Fuel Injector
L-M-NL1066T, M99C2 - M1066A @ 1500 RPM - M1066A1 @ 1800 - NL1066H1
Reproduced by permission of Deere & Co., c2006. Deere & Company. All rights reserved. CDP45118

1 RE531436 1 Fuel Injector (new, includes keys 2- 3, formerly # RE507766) -
SE501103 1 Fuel Injector (remanufactured) -
2 R92352 1 Packing -
3 R500390 1 Seal -
4 RE508716 1 Clamp -
5 RE531438 1 Return Tee Kit (includes #6) -
6 16-59502 2 O-ring (Return tee seal - not shown) -
P1066 12/18
4 - 14
updated 7-12-12
Fuel Injector
L1066A, M1066A1 @ 1500 RPM, M1066A2, NL1066H2

1 RE507948 1 Fuel Injector (new, includes keys 2 and 4) (Former # RE506688) -
3 R500390 1 Washer -
4 T24472 1 Cap (for shipping) -
5 R116366 1 Screw -
6 R79604 1 Tube Nut -
7 R79605 1 Washer -
9 1 Cap (for shipping) -
P1066 12/18
4 - 15
Fuel Injector
M1066A3, NL1066H3

1 RE505079 1 Fuel Injector (includes keys 2 and 4) -
3 R500390 1 Washer -
4 T24472 1 Cap -
5 R116366 1 Screw -
6 R79604 1 Tube Nut -
7 R79605 1 Washer -
9 1 Cap -
P1066 12/18
4 - 16
updated 5-25-16
Fuel Injector
L- M- NL1066H

1 RE519730 1 Fuel Injector (includes keys 2- 6) -
2 R134920 2 Nut -
3 RE515986 6 Tube -
4 R65397 6 O-ring -
5 R505452 6 O-ring -
6 R515535 6 Washer -
7 R515044 6 Nut -
8 R504781 6 Capscrew -
9 R504779 6 Clamp -
P1066 12/18
4 - 17
Updated 7-27-16
Low Pressure Fuel Lines (DE10 System)
Reproduced by permission of Deere & Co., c2006. Deere & Company. All rights reserved. T189663
P1066 12/18
4 - 18
Updated 7-27-16
Low Pressure Fuel Lines (DE10 System)

1 27-59610 1 Tube Assembly, Injection Pump Inlet (L- M1066T) -
27-59611 1 Tube Assembly, Injection Pump Inlet (M1066A1 @ 1800 RPM) -
RE515236 1 Tube Assembly, Injection Pump Inlet (NL1066T- H1)
2 RE507598 1 Tube Assembly, Fuel Return -
3 R123594 ** Tube Nut -
4 21-09518 ** Sealing Washer -
5 R123593 ** Tube Nut -
6 R51936 ** Sealing Washer -
7 RE60037 1 Tube Assembly, Fuel Filter Inlet (L- M1066T)
27-59612 1 Tube Assembly, Fuel Filter Inlet (M1066A1 @1800 RPM) -
RE515360 1 Tube Assembly, Fuel Filter Inlet (NL1066T- H1)
8 AR85519 1 Plug -
9 RE46686 1 Plug, M12 x 1.5 -
10 51M7040 4 O-ring -
11 RE60029 2 Adapter -
12 T13814 2 Clamp -
13 19M7784 1 Capscrew, M10 x 20 -
P1066 12/18
4 - 19
Low Pressure Fuel Lines (VP44 System, 12 Volt)
L1066A, M1066A1 @ 1500 RPM, M1066A2- A3
A-10759A/ B-8612
P1066 12/18
4 - 20
updated 1-22-13
Low Pressure Fuel Lines (VP44 System, 12 Volt)
L1066A, M1066A1 @ 1500 RPM, M1066A2- A3

1 23-59603 1 Bracket, Fuel Filter Mtg. -
4 15-00801 2 Lock Washer, Hi-collar M10 S/S -
5 14-00811 2 Hex Nut M10 x 1.5 -
6 27-59614 1 Tube Assembly, Fuel Filter Inlet (units with 12 Volt filter mounted pump) -
7 27-59616 1 Tube Assembly, Injection Pump Inlet VP44 -
8 27-59618 1 Tube Assembly, Leak-off Return to Fuel Filter -
13 15-00701 2 Flat Washer M8 -
16 15-00805 2 Flat Washer M10 -
17 14-00812 1 Hex Nut, Nylock M10 x 1.5 -
18 27-59617 1 Tube Assembly, Fuel Return -
20 21-59602 1 Bulkhead Union 45° Steel, 3/8- 37T -
25
26
38M7009
R62107
1
2
Banjo Bolt *
Sealing Washer *
} for #8 tube connection
at fuel filter
-
-
27
28
38M6640
R504067
1
2
Banjo Bolt *
Sealing Washer * } for #7 tube connection
at injection pump
-
-
29
26
RE505227
R64857
1
2
Banjo Bolt *
Sealing Washer * } for #18 tube connection
at injection pump
-
-

* Not Shown
P1066 12/18
4 - 21
Low Pressure Fuel Lines, VP44 System
NL1066H2- H3
P1066 12/18
4 - 22
Low Pressure Fuel Lines, VP44 System
NL1066H2- H3
2 R64857 2 Washer -
4 AR85519 1 Plug -
5 R123593 1 Tube Nut -
6 R504067 2 Washer -
8 38M6640 1 Hollow Screw -
11 51M7040 6 O-ring -
13 RE46686 2 Plug -
15 R62107 2 Washer -
16 38M7009 1 Hollow Screw -
17 RE500576 1 Adapter -
19 R504730 1 Bracket -
20 19M7783 1 Capscrew, M10 x 16 -
21 R136082 1 Clamp -
22 19M7752 2 Capscrew, M4 x 20 -
23 14M7334 1 Flange Nut, M10 -
24 T14050 1 Clamp -
25 19M7784 1 Capscrew, M10 x 20 -
26 R504859 1 Bracket -
P1066 12/18
4 - 23
updated 7-27-16
Low Pressure Fuel Lines, High Pressure Common Rail
L- M1066H & MCA
P1066 12/18
4 - 24
updated 7-27-16
L- M1066H & MCA

3 AR85519 1 Plug -
9 RE502174 4 Elbow Fitting -
11 27-59609 1 Fuel Line, Filter Outlet L-M1066H -
27-59641 1 Tube Assembly, Filter Outlet M1066HMCA
12 27-59608 1 Fuel Line, Pump Outlet -
13 RE46686 4 Plug -
14 51M7040 8 O-ring -
16 RE500576 1 Adapter -
17 27-59607 1 Fuel Line, Pump Inlet -
18 R516453 1 Adapter -
19 R500271 2 O-ring -
21 T13814 1 Clamp -
22 23-59602 1 Bracket L-M1066H -
R116116 1 Bracket M1066HMCA
P1066 12/18
4 - 25
NL1066H4
Reproduced by permission of Deere & Co., c2006. Deere & Company. All rights reserved. RE517149SPAnl
P1066 12/18
4 - 26
NL1066H4

1 RE51936 7 Sealing Washer -
3 AR85519 1 Plug -
9 RE502174 4 Elbow Fitting -
11 RE517221 1 Fuel Line, Filter Outlet -
12 RE517245 1 Fuel Line, Pump Outlet -
13 RE46686 4 Plug -
14 51M7040 8 O-ring -
16 RE500576 1 Adapter -
18 R516453 1 Adapter -
19 R500271 2 O-ring -
21 T13814 1 Clamp -
22 R116116 1 Bracket -
P1066 12/18
4 - 27
updated 7-27-16
Fuel Filter DE10 System
L- M- NL1066T - M99C2 - M1066A @ 1500 RPM - M1066A1 @1800 RPM - NL1066H1

1 RE509794 1 Filter Head Assembly -
2 19M7784 2 Screw -
3 RE516553 1 Seal Kit -
5 R113562 1 Ring -
6 RE509031 1 Filter Element -
7 RE51650 1 Sediment Bowl - Industrial Only -
8 RE516512 1 Seal Kit -
9 RE60854 1 Cap Kit - Industrial Only -
24-51006 1 Drain Valve - Marine -
10 RE51649 1 Seal Kit -
11 R113565 1 Seal -
P1066 12/18
4 - 28
Secondary Fuel Filter VP44 System

L1066A, M1066A1 @1500 RPM, M1066A2- A3, NL1066H2- H3
Reproduced by permission of Deere & Co., c2006. Deere & Company. All rights reserved. RGP8265a

1 RE508985 1 Repair Kit -
2 19M7784 2 Screw -
3 RE516553 1 Seal Kit -
5 R113562 1 Ring -
7 RE51650 1 Sediment Bowl - Industrial Only -
8 RE516512 1 Seal Kit -
9 RE60854 1 Cap Kit - Industrial Only -
24-51006 1 Drain Valve - Marine -
10 RE51649 1 Seal Kit -
11 R113565 1 Seal -
12 RE167207 1 Sensor, Fuel Pressure -
13 RE507487 1 Adapter -
14 51M7040 1 O-ring -
P1066 12/18
4 - 29
Primary Fuel Filter Water Separator, VP44
L1066A, M1066A1 @ 1500 RPM, M1066A2- A3, & NL1066H2- H3
Reproduced by permission of Deere & Co., c2006. Deere & Company. All rights reserved. CDP45192
P1066 12/18
4 - 30
Primary Fuel Filter Water Separator, VP44
L1066A, M1066A1 @ 1500 RPM, M1066A2- A3, & NL1066H2- H3

1 RE508847 ** Filter Head Assembly (includes keys 8, 9, 12-14, and 16) -
2 RE516553 ** Kit -
3 RE509208 1 Filter Element (also order R113565) -
4 RE509033 ** Pump Kit, 12 Volt -
5 RE60854 ** Kit, Industrial -
24-51006 1 Drain Valve, Marine -
6 RE51650 ** Sediment Bowl Kit, Industrial only (includes keys 17-26) -
8 R504007 1 O-ring -
9 RE516512 1 Kit -
10 RE51649 1 Filter Repair Kit (units with separate 24 Volt Pump) -
11 51M7040 ** O-ring -
12 RE46686 ** Plug -
13 1 Drain Plug* (order key #1 or #10 or #5) -
14 R113565 1 Seal -
15 1 Filter Element* (order key #3 and #14) -
16 1 Retainer* (order key #1) -
17 1 O-ring* (order key #2 or #6) -
18 1 Retainer* (order key #6) -
20 1 Nut* (order key #6) -
21 1 Lock Washer* (order key #6) -
22 1 Washer* (order key #6) -
23 1 Sediment Bowl* (order key #6) -
24 1 O-ring* (order key #6 or #2 or #5) -
25 1 Gasket* (order key #6 or #2 or #5) -
26 1 Drain Plug* (order key #6 or #5) -
27 1 Screw* (order key #6) -
29 R505143 1 Bracket (not shown) -
30 28H1529 1 Bushing (not shown) -
31 19M7808 1 Screw, M10 x 65 mm (not shown) -
32 19M7784 3 Screw, M10 x 20 mm (not shown) -
*Not available separately

**As required
P1066 12/18
4 - 31
Secondary Fuel Filter
L- M1066H & NL1066H4
RGP8997

1 RE509794 1 Filter Head Assembly (includes keys 2 and 3) -
2 R113562 1 O-ring -
3 R113563 1 Plug Vent -
5 RE60854 1 Kit -
6 RE51649 1 Seal Kit -
7 RE516553 1 Kit -
8 R516437 1 Bracket - Industrial -
23-59602 1 Bracket - Marine -
P1066 12/18
4 - 32
Updated 7-12-12
Primary Fuel Filter/ Water Separator
L- M1066H & NL1066H4

1 RE508847 1 Filter Head Assembly -
2 19M7786 2 Screw -
3 R113562 1 Ring -
4 R113563 1 Vent Plug -
5 RE51649 1 Seal Kit -
6 RE509036 1 Fuel Filter (former # RE517180) -
7 RE51650 1 Sediment - Industrial only -
8 RE60854 1 Drain Valve - Industrial only -
9 R113565 1 Seal -
10 R113562 1 Ring -
11 RE516553 1 Seal Kit -
RE516512 1 O-ring Kit -
12 24-51006 1 Drain Valve - Marine (not shown) -
P1066 12/18
4 - 33
Electric Fuel Pump, 24 Volt Standard Ground
L1066A
A-11130/ B-8940

1 RE515718 1 Electric Fuel Pump 24 Volt DC (VP44 System) -
2 R500270 1 Male Connector, Brass M10 x 1.0 x 5/16 -
3 R500271 1 O-ring -
4 14M7265 2 Lock Nut -
5 14M7264 1 Lock Nut M4 x 0.07 -
6 R515460 1 Bracket -
7 R515461 1 Cushion -
8 R515736 1 Spacer -
9 19M7986 1 Capscrew, Hex Head M5 x 0.8 x 50 mm -
10 23-59606 1 Bracket, Electric Fuel Pump Mtg. -
13 15-00701 4 Flat Washer M8 -
14 14-00711 2 Hex Nut M8 x 1.25 -
17 27-59629 1 Tube Assembly, Electric Fuel Pump Inlet -
18 21-09517 1 Compression Union, Brass 5/16 -
19 27-59630 1 Tube Assembly, Electric Lift Outlet -
20 RE526834 1 Repair Kit, Fuel Filter Head -
P1066 12/18
4 - 34
Electric Fuel Pump, 24 Volt Standard Ground
M1066A1, A2, A3
A-11124/ B-8947

3 R500271 1 O-ring -
4 14M7265 2 Lock Nut -
5 14M7264 1 Lock Nut M4 x 0.07 -
6 R515460 1 Bracket -
7 R515461 1 Cushion -
8 R515736 1 Spacer -
15 27-59627 1 Tube Assembly, Electric Fuel Pump Inlet -
16 21-09517 1 Female Connector, Brass 1/4 NPT x 5/16 -
17 27-59628 1 Tube Assembly, Electric Fuel Pump Outlet -
P1066 12/18
4 - 35
Revised 7-12-12
Electric Fuel Pump, 24 Volt Isolated Ground
M1066A1, A2, A3
A-11154/ B-8946

3 R500271 1 O-ring -
4 14M7265 1 Lock Nut -
5 14M7264 1 Lock Nut M4 x 0.07 -
6 R515460 1 Bracket -
7 R515461 1 Cushion -
15 27-59638 1 Tube Assembly, Electric Fuel Pump Inlet (includes #21) -
16 21-09705 1 Female Connector, Brass 1/4 NPT x 5/16 -
17 21-09702 1 Male Connector, Brass 1/4 NPT x 3/8" -
18 21-59521 2 Sleeve, Insulating -
19 27-59628 1 Tube Assembly, Electric Fuel Pump Outlet (includes #21) -
20 21-09704 1 Tube Nut, Brass 3/8" -
21 21-09703 2 Sleeve, 3/8" O.D. (Tube sealing - not shown) -
P1066 12/18
4 - 36
Revised 7-27-16
Fuel Supply & Return Connections
L- M1066T - M99C2 - M1066A @ 1500 RPM
A-8507/ C-4210

5 21-52211 1 Bulkhead Union, Steel 1/4-37T -
6 14-00012 1 Bulkhead Nut, 7/16-20 (1/4-37T) -
10 15-00701 1 Flat Washer M8 -
12 R123593 1 Nut -
13 R51936 1 Tube Seal -
P1066 12/18
4 - 37
Revised 8-1-13

L-M1066A @ 60 Hz
A-10684/ C-5693

4 21-59512 1 Bulkhead Union, 45° Steel 1/4- 37T -
5 14-00012 1 Bulkhead Nut, 7/16- 20 (1/4-37T) -
10 15-00701 1 Flat Washer M8 -
11 R51936 1 Tube Seal -
12 R123593 1 Nut -

P1066 12/18
4 - 38
L- M1066H
A-10683/ C-8949

2 R51936 1 Tube Seal -
5 21-52211 1 Bulkhead Union, Steel 1/4-37T -
6 14-00012 1 Bulkhead Nut, 7/16-20 (1/4-37T) -
10 15-00701 1 Flat Washer M8 -
11 21-59508 1 Male Connector, Steel 3/8- 37T x M12 x 1.5 -
12 R123593 1 Nut -
13 21-52213 1 Elbow, 900 Swivel Steel 3/8- 37T -
P1066 12/18
4 - 39
Fuel Filter Bypass

M1066H
A-11161/ A-11268

1 21-59508 2 Male Connector, Steel 3/8- 37T x M12 x 1.5 -
2 21-59522 1 Elbow, 90° Swivel, Steel 3/8- 37T x 1/4 NPT -
3 36-70018 1 Check Valve, Steel 1/4 NPSF -
5 27-59510 1 Tube Assembly, Fuel Filter Bypass -
7 21-71055 1 Male Elbow 90° Steel 1/8 NPT x 3/8- 37T (at fuel pump inlet- -
not shown) -
P1066 12/18
4 - 40
Fuel Transfer Pump
L- M- NL1066T, M99C2, L1066A, M1066A1,

NL1066H1, L-M1066H, and NL1066H4

1 RE68345 1 Fuel Pump (L-M-NL1066T, M99C2, L1066A, M1066A1, NL1066H1) -
RE517230 1 Fuel Pump (L-M1066H, NL1066H4) -
2 R123273 1 O-ring -
3 R500271 2 O-ring -
4 R500270 ** Connector, M10 x 1.0 x 5/16 Compression (L-M-NL1066T, M99C2, -
L1066A, M1066A1, NL1066H1) -
R516543 ** Connector, M10 x 1.0 x 3/8 Compression (L-M1066H, NL1066H4) -
5 R500269 1 Fitting -
6 RE504233 2 Screw -
7 R133405 1 Push Rod -
**As required
P1066 12/18
4 - 41
Updated 2-24-11
GROUP 5 - ELECTRICAL SYSTEM
Engine Electrical 12 Volt Standard Ground
L1066T & L1066H
A-10487, A-10489/ B-8787_new
P1066 12/18
5-0

L1066T & L1066H

1 RE70957 1 Starter, 12 Volt Standard Ground -
3 23-40009 1 Bracket, Solenoid Mtg. -
4 19-00088 1 Hose Clamp #88 -
5 22-41080 1 Solenoid 12 VDC 65 Amp -
6 14-00112 2 Hex Nut, Nylock 1/4- 20 -
7 15-00121 2 Flat Washer 1/4" SAE -
8 21-09601 1 Bushing, Steel 1/2 NPT x M14 x 1.5 -
9 AT157679 1 Transient Voltage Protector 12 V (not shown) -
10 22-49513 1 Engine Wire Harness Assembly L1066T up to s/n xxxx-3019
22-49523 1 Engine Wire Harness Assembly L1066T from s/n xxxx-3020
22-49608 1 Engine Wire Harness Assembly L1066H up to s/n xxxx-3096
22-49618 1 Engine Wire Harness Assembly L1066H from s/n xxxx-3097
11 RE52722 1 Sensor, Coolant Temperature -
12 RE61812 1 Sensor, Air Temperature -
13 RE519144 1 Speed Sensor -
14 RE167207 1 Sensor, Oil & Fuel Pressure -
P1066 12/18
5-1
Updated 2-24-11
Engine Electrical 12 Volt Isolated Ground
L1066T & L1066H
A-10487, A-10489/ B-8787_new
P1066 12/18
5-2

L1066T & L1066H

1 21-41647 1 Starter, 12 Volt Isolated Ground L1066T -
22-49507 1 Starter, 12 Volt Isolated Ground L1066H -
4 19-00088 1 Hose Clamp #88 -
5 22-41080 1 Solenoid 12 VDC 65 Amp -
6 14-00112 2 Hex Nut, Nylock 1/4- 20 -
7 15-00121 2 Flat Washer 1/4" SAE -
P1066 12/18
5-3
Updated 2-24-11
L1066T & L1066H
A-10487, A-10489/ B-8787_new
P1066 12/18
5-4

L1066T & L1066H

1 22-41648 1 Starter, 24 Volt Standard Ground L1066T -
RE70961 1 Starter, 24 Volt Standard Ground L1066H -
4 19-00088 1 Hose Clamp #88 -
5 22-41079 1 Solenoid 24 VDC 65 Amp -
6 14-00112 2 Hex Nut, Nylock 1/4- 20 -
7 15-00121 2 Flat Washer 1/4" SAE -
P1066 12/18
5-5
Updated 2-24-11
L1066T & L1066H
A-10487, A-10489/ B-8787_new
P1066 12/18
5-6

L1066T & L1066H

1 22-41648 1 Starter, 24 Volt Standard Ground L1066T -
22-49508 1 Starter, 24 Volt Isolated Ground L1066H -
4 19-00088 1 Hose Clamp #88 -
5 22-41079 1 Solenoid 24 VDC 65 Amp -
6 14-00112 2 Hex Nut, Nylock 1/4- 20 -
7 15-00121 2 Flat Washer 1/4" SAE -
P1066 12/18
5-7

M1066
A-10490, A-11103, A-11104/ C-5667
P1066 12/18
5-8
M1066

1 22-70083 1 Relay Board Assembly (see parts detail) -
22-70086 1 Relay Board Assembly, Autostart Units (see parts detail)
2 12-00001 4 Machine Screw BH Slotted #10- 32 x 3/4" S/S -
3 14-00006 4 Hex Nut, Nylock #10- 32 -
4 22-40915 1 Pressure Switch 15 PSI 1/8 NPT -
5 22-40907 1 Temperature Switch 205°F -
7 19-00088 1 Hose Clamp #88 -
8 22-41080 1 Solenoid 12 VDC 65 Amp Isolated Ground -
9 12-80111 2 Hex Nut, Flanged 1/4- 20 -
10 15-00121 2 Flat Washer 1/4" SAE -
11 RE70957 1 Starter, 12 V Standard Ground -
RE70960 1 Starter, 12 V Standard Ground (M1066H only, with double wall fuel lines) -
13 AT157679 1 Transient Voltage Protector 12V -
14 21-09601 1 Bushing, M14 x 1.5 x 1/2 NPT -
15 22-49511 1 Wire Harness (M1066T & M1066A1 @1800 RPM) -
22-49603 1 Wire Harness (M1066A1 @1500 RPM & M1066A2- A3) -
22-49509 1 Wire Harness (M1066H) -
16 22-41016 1 Oil Pressure Sender 0-80 PSI, Single Station -
17 22-41026 1 Temperature Sender 250°F, Single Station -
18 10-40001 1 Oil Pressure Manifold -
19 21-13110 2 Spacer -
22 21-00113 1 Elbow 45° Swivel, Steel 1/4- 37T -
23 18-55405 1 Hose Assembly 1/4" I.D. x 9" -
24 21-71049 1 Male Elbow 90° Steel, 1/4 NPT x 1/4- 37T -
26 22-42047 1 Relay, 12 Volt
27 RE167207 1 Oil Pressure Sensor* -
28 RE52722 1 Coolant Temperature Sensor -
29 RE61812 1 Air Temperature Sensor -
31 37-90086 1 Engine Data Module (optional) -
}
32 22-40910 1 Temperature Switch 195°F 3/8 NPT -
34 22-41077 1 Terminal Strip -
Optional for pre-alarm
35 12-00005 2 Machine Screw functions -
36 14-00003 2 Hex Nut, Nylock -
*Also fuel pressure on L1066A - M1066A1 @ 1500 & M1066A2 - A3; see
secondary fuel filter.
P1066 12/18
5-9
M1066
A-10491/ C-5667
P1066 12/18
5 - 10
M1066

3 14-00006 4 Hex Nut, Nylock #10- 32 -
7 19-00088 1 Hose Clamp #88 -
9 12-80111 2 Hex Nut, Flanged 1/4- 20 -
10 15-00121 2 Flat Washer 1/4" SAE -
11 22-41647 1 Starter, 12 V Isolated Ground -
22-49507 1 Starter, 12 V Isolated Ground (M1066H only) -
14 21-09601 1 Bushing, M14 x 1.5 x 1/2 NPT -
22-49509 1 Wire Harness (M1066H) -
19 21-13110 2 Spacer -
26 22-42047 1 Relay, 12 Volt
}
34 22-41077 1 Terminal Strip Optional for pre-alarm -
36 14-00003 2 Hex Nut, Nylock -
P1066 12/18
5 - 11
M1066
A-10492, A-11107/ C-5667
P1066 12/18
5 - 12
M1066

3 14-00006 4 Hex Nut, Nylock #10- 32 -
7 19-00088 1 Hose Clamp #88 -
9 12-80111 2 Hex Nut, Flanged 1/4- 20 -
10 15-00121 2 Flat Washer 1/4" SAE -
RE70961 1 Starter, 24 V Isolated Ground (M1066H only) -
14 21-09601 1 Bushing, M14 x 1.5 x 1/2 NPT -
22-49509 1 Wire Harness (M1066H) -
19 21-13110 2 Spacer -
26 22-40085 1 Relay, 24 Volt
}
36 14-00003 2 Hex Nut, Nylock -
P1066 12/18
5 - 13
M1066
A-10493/ C-5667
P1066 12/18
5 - 14
M1066

3 14-00006 4 Hex Nut, Nylock #10- 32 -
7 19-00088 1 Hose Clamp #88 -
9 12-80111 2 Hex Nut, Flanged 1/4- 20 -
10 15-00121 2 Flat Washer 1/4" SAE -
22-49508 1 Starter, 24 V Isolated Ground (M1066H only) -
14 21-09601 1 Bushing, M14 x 1.5 x 1/2 NPT -
22-49509 1 Wire Harness (M1066H) -
19 21-13110 2 Spacer -
26 22-40085 1 Relay, 24 Volt
}
36 14-00003 2 Hex Nut, Nylock -
P1066 12/18
5 - 15
NL1066T, H1, H2, H3, and H4
P1066 12/18
5 - 16
NL1066T, H1, H2, H3, and H4

1 22-70083-1 1 Relay Board Assembly (see parts detail) -
2 12-00001 4 Machine Screw, BH Slotted #10- 32 x 3/4" S/S -
3 14-00006 4 Hex Nut, Nylock #10- 32 -
6 23-40009 1 Bracket, Solenoid Mounting -
7 19-00088 1 Hose Clamp #88 -
8 22-41080 1 Solenoid 12 VDC 65 Amp -
9 14-00112 2 Hex Nut Nylock 1/4- 20 -
10 15-00121 2 Flat Washer 1/4" SAE -
11 RE70957 1 Starter 12 Volt -
13 AT157679 1 Transient Voltage Protector 12 Volt -
14 22-49511 1 Wire Harness (NL1066T- H1 only) -
15 22-41016 1 Pressure Sender 0-80 PSI Standard Ground -
16 22-41026 1 Temperature Sender 2500F Standard Ground -
17 AT173624 1 Alternator 12 Volt 65 Amp (see mounting detail) -
*Also fuel pressure on NL1066H2 & H3; see secondary fuel

filter.
P1066 12/18
5 - 17
Revised 2-15-08
GROUP 5 - ELECTRICAL SYSTEMS
12 Volt/ 65 Amp Medium Frame Alternator
L- M- NL1066T, M99C2, M1066A1,A2, A3, NL1066H1, H2, H3

•• 22-49531 1 Alternator Assembly (includes keys #1-10) -
1 AT173624 1 Alternator 12 Volt 65 Amp (see mounting detail) -
2 T158584 1 Fan -
3 R501486 1 Pulley -
4 14M7158 1 Nut -
5 T10745 1 Washer -
6 14M7297 1 Nut, M5 -
8 RE12362 1 Electrical Connector Assembly -
9 H144095 1 Capacitor -
10 H144094 1 Voltage Regulator -
11 19M7812 1 Screw -
14 R48808 1 Washer -
15 19M7867 1 Capscrew, M8 x 25 -
P1066 12/18
5 - 18
Revised 2-15-08
24 Volt/ 45 Amp Medium Frame Alternator
L- M- NL1066T, M99C2, M1066A1,A2, A3, NL1066H1, H2, H3
RGP8262

•• 22-49533 1 Alternator Assembly (includes keys #1-8) -
1 TY24322 1 Alternator 24V/ 45 Amp (see mounting detail) -
2 T158584 1 Fan -
3 R501486 1 Pulley -
4 14M7158 1 Nut -
5 T10745 1 Washer -
6 14M7297 1 Nut -
8 RE12362 1 Electrical Connector Assembly -
9 19M7812 1 Screw -
12 R48808 1 Washer -
13 19M7867 1 Screw -
P1066 12/18
5 - 19
Updated 12-31-08
Medium Frame Alternator & Mounting
L- M1066T, M99C2, L1066A, M1066A1, A2, A3
Former one-piece bracket
A-8530/ B-9502

1 22-49531 1 Alternator, 12 Volt/ 65 Amp Isolated Ground (see parts detail) -
22-49533 1 Alternator, 24 Volt/ 45 Amp Isolated Ground (see parts detail) -

2 23-49521
23-49522
1
1
Bracket, Lower
Bracket, Upper }replaces former one piece bracket
-
-
3 R132166 1 Bracket -
6 12-80088 1 Capscrew, Hex Head Flanged, M10 x 1.5 x 95 mm -
7 R64525 1 Shim -
8 R100377 1 Bushing -
9 14-80811 1 Flange Nut -
10 15-49501 ** Spacer -
**As required
P1066 12/18
5 - 20
Updated 12-31-08
Medium Frame Alternator & Mounting
L- M1066T, M99C2, L1066A, M1066A1, A2, A3
Former one-piece bracket
Supplied
with alternator
A-8530/ B-6405

1 22-40523 1 Alternator, 12 Volt/ 51 Amp Iso. Ground (replaces 22-40512) -
22-40513 1 Alternator, 24 Volt/ 35 Amp Isolated Ground -
2 34-49502 1 Pulley 8 Groove 2.36" O.D. x 5/8" I.D. -

3 23-49521
23-49522
1
1
Bracket, Lower
Bracket, Upper } replaces former one piece bracket
-
-
4 31-49501 1 Alternator Mounting Adapter -
5 21-49502 1 Spacer, Steel 1" O.D. x 13/32" I.D. x 6.8 mm -
7 14-80811 1 Hex Nut, Flanged M10 x 1.5 mm -
8 12-00213 1 Capscrew, Hex Head 5/16-18 x 1- 1/4" -
10 15-00221 1 Flat Washer, 5/16" SAE -
11 R132166 1 Bracket -
17 R100377 1 Bushing -
18 22-70048 1 Diode Harness Addition (used only with 12V/ 51 Amp Alternator, not shown) -
P1066 12/18
5 - 21
Medium Frame Alternator Mounting
L- M1066H with 12V/ 65 Amp or 24V/ 45 Amp Alternator

1 R516584 1 Bracket -
2 19M7786 7 Capscrew, M10 x 30 mm -
3 19M7785 2 Capscrew, M10 x 25 mm -
4 19M7801 2 Capscrew, M8 x 60 mm -
5 R516510 1 Support -
6 23-49516 1 Bracket -
7 14M7296 3 Flange Nut, M10 -
8 R516574 1 Bracket -
9 R134010 1 Bushing -
10 R135423 1 Bushing -
P1066 12/18
5 - 22
NL1066T - H1- H2- H3

1 19M7786 5 Capscrew, M10 x 30 mm -
2 R100377 1 Bushing -
3 R132166 1 Bracket -
5 R132168 1 Support -
6 19M7785 2 Capscrew, M10 x 25 -
7 19M7801 2 Capscrew, M8 x 60 mm -
8 34M7061 1 Spring Pin -
9 R132167 1 Bracket -
10 14M7296 3 Flange Nut, M10 -
P1066 12/18
5 - 23
NL1066H4 with 12V/ 65 Amp or 24V/ 45 Amp Alternator
Reproduced by permission of Deere & Co., c2006. Deere & Company. All rights reserved. RE517274SPA&RGP5656

1 R516584 1 Bracket -
2 19M7786 7 Capscrew, M10 x 30 mm -
3 19M7785 2 Capscrew, M10 x 25 mm
4 R516569 1 Strap -
5 14M7296 3 Flange Nut, M10 -
6 R134010 1 Bushing -
7 R516574 1 Bracket -
8 R135423 1 Bushing -
9 R516508 1 Support Bracket -
10 19M7801 2 Capscrew, M8 x 60 mm -
P1066 12/18
5 - 24
Notes
P1066 12/18
5 - 25
12 Volt 65 Amp Medium Frame Alternator & Mounting

L1066H Early Production
A-10258/ B-8593
P1066 12/18
5 - 26
12 Volt 65 Amp Medium Frame Alternator & Mounting

L1066H Early Production

1 AT173624 1 Alternator, 12 Volt 65 amp, Standard Ground (includes keys 13-15) -
2 23-49511 1 Bracket, Medium Frame Alternator Mounting -
3 23-49514 1 Bracket, Alternator Mounting -
4 23-49512 1 Bracket -
5 23-49513 1 Bracket -
9 R100377 1 Bushing -
11 1 Spacer -
13 T158584 1 Fan -
14 R501486 1 Pulley -
15 R48808 1 Washer -
16 H144095 1 Capacitor -
17 H144094 1 Voltage Regulator -
18 14M7297 1 Nut, M5 -
Note: Installed only on units with the following serial #s:

0661-2559
0661-2704
0661-2705
0661-2712
P1066 12/18
5 - 27
Large Frame Alternators & Mounting
L- M1066T, M99C2, L1066A, and M1066A1, A2, A3
A-8609, A-8610/ C-4545
P1066 12/18
5 - 28
Large Frame Alternators & Mounting

L- M1066T, M99C2, L1066A, and M1066A1, A2, A3

1 22-40282 1 Alternator, 12 Volt 140 Amp Isolated Ground (replaced by 22-40504) -
22-40504 1 Alternator, 12 Volt 160 Amp Isolated Ground (supercedes 22-40282) -
22-40277 1 Alternator, 24 Volt 75 Amp Isolated Ground -
2 34-49503 1 8 Groove Pulley, 3-1/4" O.D. x 7/8" I.D. -
3 23-49502 1 Alternator Support Mounting Bracket -
4 23-49503 1 Alternator Mounting Bracket -
7 15-00802 4 Lock Washer, Helical, M10 -
10 14-00811 2 Hex Nut, M10 x 1.5 -
11 12-00515 1 Capscrew, Hex Head, 1/2 -13 x 1 -3/4" -
12 15-00504 3 Flat Washer, 1/2" SAE -
13 14-00512 2 Hex Nut, Nylock 1/2-13 -
16 19M7786 ** Capscrew, Hex Head Flanged, M10 x 1.5 x 30 mm -
18 12-00516 1 Capscrew, Hex Head 1/2 -13 x 2" -
**As required
P1066 12/18
5 - 29
Large Frame Alternator & Mounting
L- M1066T, M99C2, L1066A, M1066A1, A2, A3
A-10231 & A-10375/ C-4545
P1066 12/18
5 - 30
L- M1066T, M99C2, L1066A, M1066A1, A2, A3

1 22-45018 1 Alternator, 24 Volt 100 Amp Isolated Ground -
22-40227 1 Alternator, 24 Volt 175 Amp Isolated Ground -
10 14-00811 2 Hex Nut, M10 x 1.5 -
12 15-00504 3 Flat Washer, 1/2" SAE -
13 14-00512 2 Hex Nut, Nylock 1/2 -13 -
16 19M7786 ** Capscrew, Hex Head Flanged, M10 x 1.5 x 30 mm (**As required) -
P1066 12/18
5 - 31

L- M1066H
A-10389, A-10390/ C-5762
P1066 12/18
5 - 32
L- M1066H

1 22-40282 1 Alternator, 12 Volt/ 140 Amp Isolated Ground (replaced by 22-40504) -
22-40504 1 Alternator, 12 Volt/ 160 Amp Isolated Ground (supercedes 22-40282) -
22-40277 1 Alternator, 24 Volt/ 75 Amp Isolated Ground -
10 14-00811 2 Hex Nut, M10 x 1.5 -
12 15-00504 3 Flat Washer, 1/2" SAE -
13 14-00512 2 Hex Nut, Nylock 1/2 -13 -
P1066 12/18
5 - 33
Updated 2-15-08
12 & 24 Volt Relay Logic Board

Manual Start
A-8851, A-8852, A-8854, A-8855/ C-2041C

•• 22-70083 1 12V Relay Logic Board, Manual Start (Includes all keys) -
•• 22-70084 1 24V Relay Logic Board, Manual Start (Includes all keys) -
1 22-41060 2 6 amp Diode (not shown) -
2 22-42047 4 12V Relay SPDT -
22-40085 4 24V Relay SPDT -
3 22-40391 4 Relay Base -
22-40393 4 Clip -
4 22-40193 1 12 Connection Terminal Board, 600 VAC -
5 22-40018 1 10 amp Circuit Breaker -
6 28-40001 1 Relay Board Mounting Plate- Manual Start -
7 22-40393 4 Terminal Retainer Clip -
8 12-00083 2 Machine Screw, Flat Head Countersunk #8-32 x 3/4" -
10 14-00003 2 Hex Nut, Nylock, #8 x 32 -
11 12-40225 2 Machine Screw, Flat Head Countersunk, #8-32 x 7/8" -
12 15-00001 4 Flat Washer, #8 -
13 22-40347 1 Wire Harness, Manual Start (not shown) -
14 14-00000 4 Hex Nut #8- 32 -
P1066 12/18
5 - 34
Added page 2-15-08

Autostart
A-8854, A-8855/ C-2041

•• 22-70086 1 12V Relay Logic Board, Autostart (Includes all keys) -
2 22-42047 4 12V Relay SPDT -
22-40085 4 24V Relay SPDT -
3 22-40391 4 Relay Base -
6 28-90018 1 Relay Board Mounting Plate -
7 22-40393 4 Terminal Retainer Clip (not shown) -
10 14-00003 4 Hex Nut, Nylock, #8 x 32 -
12 15-00001 4 Flat Washer, #8 -
13 22-40392 1 Wire Harness, Autostart (not shown) -
14 14-00000 4 Hex Nut #8- 32 -
P1066 12/18
5 - 35
Added page 2-15-08

Autostart/ Energise-To-Stop/
Redundant Power Supply
A-11644, A-11645/ C-2041

1 22-00089 1 Number Strip (not shown) -
2 22-42047 3 12V Relay SPDT -
22-40085 3 24V Relay SPDT -
3 22-40391 3 Relay Base -
6 28-40001 1 Relay Board Mounting Plate -
7 22-40393 3 Terminal Retainer Clip (not shown) -
10 14-00003 3 Hex Nut, Nylock, #8 x 32 -
12 15-00001 4 Flat Washer, #8 -
13 22-40420 1 Wire Harness, Autostart (not shown) -
14 14-00000 3 Hex Nut #8- 32 -
P1066 12/18
5 - 36
Notes
P1066 12/18
5 - 37
Added pages 2-13-09
GROUP 5 – ELECTRICAL SYSTEM
NEMA 3R DC Electrical Enclosure & Relay Panel
A-12021, 12022, 12023, 12024/ B-9556
P1066 12/18
5 - 38
Updated pages 4/1/14
GROUP 5 – ELECTRICAL SYSTEM
NEMA 3R DC Electrical Enclosure & Relay Panel

•• 22-70183 1 Relay Panel Assembly, Manual Start (includes keys #13-23) -
•• 22-70186 1 Relay Panel Assembly, Autostart (includes keys #13-23) -
•• 22-70193 1 Relay Panel Assembly, Energise-to-stop & Redundant Power -
Supply (includes keys #13-23) -
1 39-40047 1 Enclosure, NEMA 3R (former # 39-42036) -
28-40048 1 Cover
3 28-49502 1 Plate, D.C. Enclosure Mtg. -
4 15-00014 2 Head/ Tail Washer -
5 14-00812 2 Hex Nut, Nylock M10 x 1.5 Class 8 -
7 15-00008 ** Flat Washer M6 -
8 14-04803 8 Hex Nut, Nylock M6 x 1.0 Class 8 -
9 00-49503 4 Receptacle, Screw Retainer -
10 12-72006 4 Sheet Metal Screw, Truss Head Phillips #10 -
11 15-00036 ** Flat Washer #10 Nylon -
12 00-73109 2 Grommet 1-1/2” ID x 2-1/8” OD -
13 28-49501 1 Back Plane -
14 22-99537 1 Harness Assembly, Manual Start (includes key #23) -
22-99538 1 Harness Assembly, Autostart -
22-99539 1 Harness Assembly, Autostart with Redundant Power Supply -
15 22-40391 3 Relay Base (without retainer) -
16 22-40393 3 Terminal Retainer -
18 22-40018 1 Circuit Breaker -
19 12-00005 4 Machine Screw, Phillips #8-32 x 3/4” S/S -
22 15-00001 2 Flat Washer #8 -
23 22-41060 4 Diode 6 Amp (for use with Harness 22-99537) -
24 22-42047 ** Relay 12 Volt -
22-40085 ** Relay 24 Volt -
**As required
Optional
25 37-90086 1 Powerview Module -
26 22-99506 1 Wire Harness (not shown) -
P1066 12/18
5 - 39
Updated 7-13-12
Drive Belt Tensioner

1 RE518097 1 Tensioner (supercedes RE70536)* -
R70536 1 Tensioner (replaced by RE518097)* -
2 R503813 1 Bolt -
RE505264 1 Idler -
3 19M7811 1 Screw, M10 x 90 mm (use with RE518097) -
19M8131 1 Screw, M10 x 70 mm (use with RE70536) -
4 R518210 1 Spacer (Marine - use with RE518097) -
R516623 1 Spacer (Industrial - use with RE518097) -
R500321 1 Spacer (Industrial - use with RE70536) -
5 19M7801 1 Screw -
7 R132168 1 Support Bracket (NL1066T - H1- H2- H3) -
R516508 1 Support Bracket (NL1066H4) -
8 19M7801 1 Screw -
* Requires spacer R518210 & screw 19M7811 when replacing earlier tensioner
P1066 12/18
5 - 40
updated 2-2-11
Manual Drive Belt Tensioner
A-10727/ B-9664A

•• 34-09505 1 Manual Belt Tensioner Assembly (includes all keys) -
1 R500710 1 Nut -
2 23-49506 1 Bracket -
3 R518518 1 Spacer* -
4 RE518988 1 Idler Pulley (Single Bearing) -
5 19M7805 1 Screw, M10 x 45 mm* -
6 19M7785 1 Screw, M10 x 25 mm -
}
7 R517324 1 Cover* -
8 15-00701 1 Flat Washer M8 -
9 15-00708 1 Stud Washer M8 1066H -
19M7785 2 Screw, M10 x 25 mm (1066T, A1, A2, A3) -
Note: Items listed replace spacer R501466, Two Bearing Pulley

RE505264, Sleeve R502079, and Capscrew 19M8528.
P1066 12/18
5 - 41
Idler Pulley & Mounting
A-9878/ B-9398

1 23-79501 1 Bracket, Idler Mtg. -
2 R132913 1 Support -
3 R132166 1 Alternator Mounting Bracket -
8 14-80811 4 Hex Nut, Flanged M10x 1.5 -
9 R100377 1 Bushing -
11 R133643 1 Spacer -
12 AT211041 1 Pulley, Poly-V -
13 R502079 1 Sleeve -
15 14-00812 1 Hex Nut, Nylock M10 x 1.5 -
16 23-71105 1 Bracket, Belt Guard Mtg., Side -
P1066 12/18
5 - 42
updated 5-24-13
Drive Belt Applications
KEY PART NUMBER QTY DESCRIPTION

Standard or Optional Medium Frame Size Alternators
12V/ 65 Amp & 24V/ 45 Amp
R123438 1 Drive Belt, L- M1066T, M99C2, L1066A, M1066A1, A2, A3 (formerly # R123437)
R123437 1 L1066H Early Production*
R123308 1 Drive Belt, L1066H Late Production and M1066H all
R123454 1 Drive Belt, NL1066T
R123451 1 Drive Belt, NL1066H1, H2, H3
R123436 1 Drive Belt, NL1066H4
Optional Large Frame Size Alternators - 12V/ 130 Amp, 24V/ 75 Amp, 24V/ 100 Amp
R123457 1 Drive Belt, L- M1066T, L1066A, M1066A1, A2, A3, L- M1066H
Notes:
ADE supplies an additional spare belt on units equipped with front power take-off.
Contact dealer or factory for belts on custom engineered accessories (unit serial number
required).
*Early Production serial numbers:

0661-2559
0661-2704
0661-2705
0661-2712

P1066 12/18
5 - 43
Engine Control Unit
L1066H
RGP9103prop

1 23-59607 1 Bracket, Engine Control Unit -
3 15-00804 1 Wave Washer, M10 -
5 15-00904 2 Wave Washer, M12 -
8 14-00711 1 Hex Nut, M8 x 1.25 -
11 14-00808 3 Lock Nut, Flanged M10 x 1.5 -
12 R500488 3 Grommet -
13 RE500588 1 Bracket -
P1066 12/18
5 - 44
Engine Control Unit

NL1066
RGP9103

1 19M8804 4 Screw, M6 x 65 -
2 RE522510 1 Engine Controller -
3 R500488 3 Isolator -
5 19M7865 2 Screw, M8 x 16 -
6 R516658 1 Bracket -
8 R516303 1 Bracket -
9 19M7790 1 Screw, M12 x 35 -
10 19M8551 2 Screw, M10 x 25 -
P1066 12/18
5 - 45
Main Instrument Panel 12 & 24 Volt
A-10523B, A-10466C/ B-8512
P1066 12/18
5 - 46
Main Instrument Panel 12 & 24 Volt

•• 22-99706 1 Main Instrument Panel Kit, 12 Volt (includes all keys)* -
•• 22-99701 1 Main Instrument Panel Kit, 24 Volt (includes all keys)* -
•• 22-99716 1 Main Instrument Panel Kit, 12 Volt (includes all keys)** -
•• 22-99711 1 Main Instrument Panel Kit, 24 Volt (includes all keys)** -
1 28-90026 1 Panel Plate -
2 37-90087 1 Tachometer, 0-3000 RPM -
3 37-90089 1 Temperature Gauge, 250°F -
4 37-90091 1 Pressure Gauge, 0-100 PSI -
5 37-90093 1 Alarm Horn -
6 37-90099 1 Voltmeter, 8-18 VDC -
37-90095 1 Voltmeter, 16-36 VDC -
7 PVW-J-9 4 Jumper Assembly 9" -
8 37-90096 1 Hourmeter -
9 37-94803 1 Key Switch 5 Position -
10 PVJR 1 Termination Resistor -
11 22-99708 1 Wire Harness Assembly (22-99701 & 22-99706) -
22-99709 1 Wire Harness Assembly (22-99711 & 22-99716) -
12 23-99504 1 Bracket, Terminal Strip & Relay Base -
14 22-00088 1 Number Strip -
15 22-40391 1 Relay Base -
16 22-40393 1 Terminal Retainer -
17 22-42047 1 Relay, 12 VDC -
22-40085 1 Relay, 24 VDC -
18 37-40024 1 Potentiometer 1k OHM 2 Watt -
19 37-40026 1 Aluminum Knob -
20 12-00005 2 Machine Screw, BH Slotted #8-32 x 3/4" -
21 12-42404 1 Machine Screw, Truss Head Phillips #8-32 x 3/4" (not shown) -
22 14-00003 3 Hex Nut, Nylock -
23 00-00013 1 Label "12 Volt" (not shown) -
00-00014 1 Label "24 Volt" (not shown) -
24 37-90086 1 Powerview Module (not shown) -
* Used on applications with Interconnect Harness 22-49551 and

Powerview module in engine room.
**Used on applications with Interconnect Harness 22-49552 and

Powerview module connection at Main Panel.
P1066 12/18
5 - 47
Flybridge Panel 12 & 24 Volt
A-10467B/ B-8706

•• 22-99702 1 Flybridge Panel Kit, 12 and 24 Volt (includes all keys) -
1 28-90027 1 Panel Plate -
2 37-90088 1 Tachometer, 0-3000 RPM -
3 37-90090 1 Temperature Gauge, 250°F -
4 37-90092 1 Pressure Gauge, 0-100 PSI -
5 37-90094 1 Alarm Horn -
6 PVW-J-9 3 Jumper Assembly 9" -
7 37-91007 2 Switch, Push Button -
P1066 12/18
5 - 48
Auxiliary Panel 12 & 24 Volt
A-10524, A-10468/ B-8705

• 22-99705 1 Auxiliary Panel Kit -
•• 22-99707 1 Auxiliary Panel Kit, 12 Volt (includes all keys) -
•• 22-99703 1 Auxiliary Panel Kit, 24 Volt (includes all keys) -
1 28-74801 1 Panel Plate -
2 37-90016 1 Pyrometer Assembly 180°F (100°C) -
3 37-90101 1 Pressure Gauge, 0-80 PSI, 12 Volt -
37-90098 1 Pressure Gauge, 0-80 PSI, 24 Volt -
4 37-90100 1 Gear Pressure Gauge, 0-400 PSI,12 Volt -
37-90097 1 Gear Pressure Gauge, 0-400 PSI, 24 Volt -
5 22-40272 1 Bulb, 12 Volt -
22-40286 1 Bulb, 24 Volt -
6 22-40325 1 Diffuser, Green 12 & 24 Volt -
7 ES2P-80 1 Sender 80 PSI (not shown) -
8 ES2PMK-400 1 Sender 400 PSI (not shown) -
9 21-55201 1 Bushing 3/8 NPT x 1/8 NPT (not shown) -
P1066 12/18
5 - 49
Added 2-15-08
Auxiliary Panel "Ocean Line" 12 & 24 Volt
Propulsion
A-11546, A-11547, A-11550,

A-11551 / B-4766Cchanged

•• 22-90660 1 12 Volt Auxiliary Panel Kit (includes all keys) -
•• 22-90665 1 24 Volt Auxiliary Panel Kit (includes all keys) -
• 22-90659 1 12 Volt Auxiliary Panel (includes keys 1 - 7) -
• 22-90664 1 24 Volt Auxiliary Panel (includes keys 1 - 7) -
1 28-74801 1 Panel Plate -
2 37-90029-1 1 Pyrometer Assembly (includes thermocouple & harness) -
3 37-90083-1 1 Oil Pressure Gauge 0-400 PSI, 12 Volt -
37-90084-1 1 Oil Pressure Gauge 0-400 PSI, 24 Volt -
4 37-90063-1 1 Pressure Gauge 0-28 PSI, 12 Volt -
37-90064-1 1 Pressure Gauge 0-28 PSI, 24 Volt -
5 22-44865 1 Wire Harness -
6 12-90002 4 Self Tapping Screw #8 x 1 Type AB Phillips* -
7 37-41004 ** Bulb, Clear - 12 Volt -
37-41003 ** Bulb, Clear - 24 Volt -
8 22-41094 1 Pressure Sender 0-30 PSI* -
9 22-40239 1 Pressure Sender 400 PSI* -
10 21-00139 ** Adapter 1/8 BSPT x 1/8 NPT* -
11 22-94803 1 Extension Harness 3 Ft.* -
12 21-34802 1 Connector for Thermocouple (included in #37-90029-1) -
13 22-40004 1 Resistor Kit (for pyrometer, 24 Volt only) -
*Not shown
**As required
P1066 12/18
5 - 50
S-1 Control Panel 12 & 24 Volt
A-8555-6/ B-5970

•• 22-90610 1 S-1 Control Panel Assembly, 12 Volt (includes all keys) -
•• 22-90615 1 S-1 Control Panel Assembly, 24 Volt (includes all keys) -
1 00-40013 1 Plate, S-1 Control Panel -
2 22-90167 1 Rocker Switch -
3 22-90168 1 Rocker Switch -
4 22-40388 1 Wire Harness, 12 Volt -
22-40389 1 Wire Harness, 24 Volt -
6 22-40012 1 Resistor, 24 Volt -
7 00-00013 1 Label "12 Volt" * -
00-00014 1 Label "24 Volt" * -
8 22-00052 1 Number Strip, Flush Panel * -
*Not shown
P1066 12/18
5 - 51
S-3B Control Panel 12 & 24 Volt
A-10525, A-10526/ C-2470

•• 22-99501 1 S-3B Control Panel Assembly, 12 Volt (includes all keys) -
•• 22-99502 1 S-3B Control Panel Assembly, 24 Volt (includes all keys) -
1 39-40008 1 Enclosure -
2 37-90081-1 1 Oil Pressure Gauge 12 Volt -
37-90082-1 1 Oil Pressure Gauge 24 Volt -
3 37-90075-1 1 Temperature Gauge 12 Volt -
37-90076-1 1 Temperature Gauge 24 Volt -
4 37-90072-1 1 DC Volt Meter, 8- 16 VDC -
37-90073-1 1 DC Volt Meter, 18- 32 VDC -
5 37-90074-1 1 Hour Meter -
6 00-91018 1 Decal -
7 22-41077 1 Terminal Board -
8 22-41051 2 Switch -
9 22-00052 1 Number Strip -
10 22-40257 1 Wire Harness * -
11 00-40028 1 Grommet -
12 37-41004 ** Bulb, 12 Volt * -
37-41003 ** Bulb, 24 Volt * -
*Not shown **As required
P1066 12/18
5 - 52
S-3C Control Panel 12 & 24 Volt
A-10521, A-10522/ C-2465

•• 22-99511 1 S-3C Control Panel Assembly, 12 Volt (includes all keys) -
•• 22-99512 1 S-3C Control Panel Assembly, 24 Volt (includes all keys) -
1 28-90010 1 Plate -
2 37-90081-1 1 Oil Pressure Gauge, 0-80 PSI 12 Volt -
37-90082-1 1 Oil Pressure Gauge, 0-80 PSI 24 Volt -
3 37-90075-1 1 Engine Temperature Gauge, 250° 12 Volt -
37-90076-1 1 Engine Temperature Gauge, 250° 24 Volt -
4 37-90072-1 1 Volt Meter, 8- 16 VDC -
37-90073-1 1 Volt Meter, 18- 32 VDC -
5 37-90074-1 1 Hour Meter 12/ 24 Volt -
6 23-90014 1 Bracket -
7 12-90007 4 Self Tapping Screw, OVH Phillips #6 -
8 22-41051 2 Switch -
9 22-41077 1 Terminal Board -
10 22-00052 1 Number Strip -
11 12-00006 2 Machine Screw, #8- 32 x 1/2 " -
12 00-00013 ** Label, 12 Volt* -
00-00014 ** Label, 24 Volt* -
13 22-40245 1 Wire Harness* -
14 37-41004 ** Bulb, 12 Volt* -
37-41003 ** Bulb, 24 Volt* -
*Not shown **As required

P1066 12/18
5 - 53
Belt Guard, Medium Frame Alternators without Front PTO
L- M1066T, M99C2, L1066A, and M1066A1, A2, A3
A-8700/ C-5053
P1066 12/18
5 - 54
Updated 5-24-13
Belt Guard, Medium Frame Alternators without Front PTO

L- M1066T, M99C2, L1066A, and M1066A1, A2, A3

1 00-09501 1 Belt Guard, Upper 1/2 -
2 00-09602 1 Belt Guard, Lower 1/2 (L- M1066T) -
00-09606 1 Belt Guard, Lower 1/2 (L1066A with Single Damper & M1066A1, A2, A3) -
00-09603 1 Belt Guard, Lower 1/2 (L1066A with Dual Dampers) -
3 23-09502 1 Bracket (units with idler assy in place of alternator) -
23-09517 1 Bracket (units with alternators)
4 23-09503 1 Bracket -
5 23-09507 1 Bracket -
6 00-00017 6 Grommet -
7 21-05002 6 Spacer -
9 15-00705 6 Lock Washer M8 S/S -
12 15-00802 2 Lock Washer M10 -
13 14-00811 1 Hex Nut M10 x 1.5 -
16 15-00018 2 Lock Washer, Hi-collar 1/4 -
19 15-00702 3 Lock Washer M8 -
20 23-09506 1 Bracket (L- M1066T) -
23-09604 1 Bracket (L1066A - M1066A1, A2, A3)
22 1 Drive Belt, Poly-V (see application chart) -
23 21-05002 ** Spacer -
**As required
P1066 12/18
5 - 55
Belt Guard, Large Frame Alternators without front PTO

L-M1066T, M99C2, L1066A, and M1066A1, A2, A3
A-8702, A-10807, A-10976/ C-5768
P1066 12/18
5 - 56
L-M1066T, M99C2, L1066A, and M1066A1, A2, A3

1 00-09503 1 Belt Guard, Upper 1/2 -
2 00-09602 1 Belt Guard, Lower 1/2 (L- M1066T) -
00-09606 1 Belt Guard, Lower 1/2 (L1066A with single damper, M1066A1,A2, A3) -
00-09603 1 Belt Guard, Lower 1/2 (L1066A with dual dampers)
3 23-09508 1 Bracket -
4 23-09503 1 Bracket -
5 23-09507 1 Bracket -
6 00-00017 6 Grommet -
7 21-05002 6 Spacer -
9 15-00705 6 Lock Washer M8 S/S -
12 15-00802 3 Lock Washer M10 -
13 14-00811 3 Hex Nut M10 x 1.5 -
16 15-00018 2 Lock Washer, Hi-collar 1/4" -
19 15-00702 3 Lock Washer M8 -
20 23-09506 1 Bracket (L- M1066T) -
23-09604 1 Bracket (L1066A, M1066A1, A2, A3) -
21 12-00714 2 Capscrew, Hex Head M8 x 1.25 x 40 mm (L- M1066T) -
12-00716 2 Capscrew, Hex Head M8 x 1.25 x 55 mm (L1066A & M1066A1,A2,A3) -
23 21-05002 ** Spacer (L1066A) -
P1066 12/18
5 - 57
Belt Guard, Medium Frame Alternators without front PTO
L- M1066H
A-11328, A-11084/ C-5768
P1066 12/18
5 - 58
Belt Guard, Medium Frame Alternators without front PTO

L- M1066H

1 00-09501 1 Belt Guard, Upper 1/2 (Early Production)* -
00-09509 1 Belt Guard, Upper 1/2 (Late Production)** -
2 00-09603 1 Belt Guard, Lower 1/2 -
3 23-09502 1 Bracket (Early Production)* -
23-09513 1 Bracket (Late Production)** -
4 23-09503 1 Bracket -
5 23-09512 1 Bracket -
6 00-00017 6 Grommet -
7 21-05002 6 Spacer -
9 15-00705 6 Lock Washer M8 S/S -
12 15-00802 2 Lock Washer M10 -
13 14-00811 1 Hex Nut M10 x 1.5 -
19 15-00702 3 Lock Washer M8 -
20 23-09604 1 Bracket -
*See Medium Frame Alternator (Early Production)

Installed on the following units only:
0661-2559
0661-2704
0661-2705
0661-2712
**See Medium Frame Alternator (Late Production)
P1066 12/18
5 - 59
L- M1066H
A-10631/ C-5768
P1066 12/18
5 - 60
L- M1066H

1 00-09503 1 Belt Guard, Upper 1/2 -
2 00-09603 1 Belt Guard, Lower 1/2
3 23-09508 1 Bracket -
4 23-09503 1 Bracket -
5 23-09507 1 Bracket -
6 00-00017 6 Grommet -
7 21-05002 6 Spacer -
9 15-00705 6 Lock Washer M8 S/S -
12 15-00802 3 Lock Washer M10 -
13 14-00811 3 Hex Nut M10 x 1.5 -
19 15-00702 3 Lock Washer M8 -
20 23-09604 1 Bracket -
P1066 12/18
5 - 61
Belt Guard, Medium Frame Alternators with PTO
L-M1066T, M99C2, L1066A, and M1066A1, A2, A3
A-8701/ C-5736
P1066 12/18
5 - 62
Updated 5-24-13
L-M1066T, M99C2, L1066A, and M1066A1, A2, A3

1 00-09501 1 Belt Guard, Upper 1/2 -
2 00-09502 1 Belt Guard, Lower 1/2 -
3 23-09502 1 Bracket (units with idler assy in place of alternator) -
23-09517 1 Bracket (units with alternators) -
4 23-09503 1 Bracket -
5 23-09507 1 Bracket -
6 00-00017 6 Grommet -
7 21-05002 6 Spacer -
9 15-00705 6 Lock Washer M8 S/S -
13 14-00811 1 Hex Nut M10 x 1.5 -
19 15-00702 1 Lock Washer M8 -
21 23-09510 1 Bracket, Extra Drive Belt Support -
24 15-00702 2 Lock Washer M8 -
25 21-05002 ** Spacer -
**As required
P1066 12/18
5 - 63
Belt Guard, Large Frame Alternators with PTO

L- M1066T, M99C2, L1066A, and M1066A1, A2, A3
A-8703/ C-5735
P1066 12/18
5 - 64
L- M1066T, M99C2, L1066A, and M1066A1, A2, A3

1 00-09503 1 Belt Guard, Upper 1/2 -
2 00-09502 1 Belt Guard, Lower 1/2 -
3 23-09508 1 Bracket -
4 23-09503 1 Bracket -
5 23-09507 1 Bracket -
6 00-00017 6 Grommet -
7 21-05002 6 Spacer -
9 15-00705 6 Lock Washer M8 S/S -
12 15-00802 2 Lock Washer M10 -
13 14-00811 1 Hex Nut M10 x 1.5 -
19 15-00702 1 Lock Washer M8 -
24 15-00702 2 Lock Washer M8 -
25 21-05002 ** Spacer -
**As required
P1066 12/18
5 - 65
L- M1066H
A-11085/ C-5736
P1066 12/18
5 - 66
L- M1066H

1 00-09509 1 Belt Guard, Upper 1/2 -
2 00-09502 1 Belt Guard, Lower 1/2 -
3 23-09513 1 Bracket, Medium Frame Alternator -
4 23-09503 1 Bracket -
5 23-09512 1 Bracket -
6 00-00017 6 Grommet -
7 21-05002 6 Spacer -
9 15-00705 6 Lock Washer M8 S/S -
13 14-00811 3 Hex Nut M10 x 1.5 -
19 15-00702 1 Lock Washer M8 -
24 15-00702 2 Lock Washer M8 -
P1066 12/18
5 - 67

L- M1066H
A-10974/ C-5735
P1066 12/18
5 - 68
L- M1066H

1 00-09503 1 Belt Guard, Upper 1/2 -
2 00-09502 1 Belt Guard, Lower 1/2 -
3 23-09508 1 Bracket -
4 23-09503 1 Bracket -
5 23-09512 1 Bracket -
6 00-00017 6 Grommet -
7 21-05002 6 Spacer -
9 15-00705 6 Lock Washer M8 S/S -
12 15-00802 2 Lock Washer M10 -
13 14-00811 3 Hex Nut M10 x 1.5 -
19 15-00702 1 Lock Washer M8 -
24 15-00702 2 Lock Washer M8 -
P1066 12/18
5 - 69
GROUP 6 - GASKET SETS
Gasket Set, Engine Overhaul

L- M1066T, M99C2
•• 29-09600 1 Gasket Set, Engine Overhaul (includes all keys) -

1 R123543 1 Gasket -
2 R521439 6 Gasket -
3 R502814 1 Gasket -
4 R123226 2 Seal -
5 R123345 1 Gasket, Thermostat Housing -
6 R123570 1 Gasket, Turbocharger Oil Outlet Tube -
7 R123575 4 O-ring -
8 R116516 1 Gasket, Cylinder Head -
9 R501373 1 Gasket -
11 R123572 1 Gasket -
12 R123354 1 Gasket, Engine Oil Pan -
13 R501428 1 Gasket -
14 R75892 1 O-ring, Oil Pump Tube Connector -
15 R97185 1 O-ring, Oil Pump Outlet Tube to Cover -
16 R61871 1 O-ring, Oil Pump Intake Tube -
17 A4827R 1 Washer, Oil Pressure Regulator Plug -
18 RE44574 1 Seal, Rear Oil -
19 RE59810 1 Front Oil Seal Kit -
20 R123273 1 O-ring, Fuel Transfer Pump -
21 R123417 1 Gasket, Water Pump -
22 R136516 1 Gasket, Timing Gear Cover -
R136515 1 Gasket, Timing Gear Cover, for Auxiliary Drive -
23 R123501 1 Gasket, Oil Cooler Housing -
24 R502864 1 Gasket, Remote Oil Filter Adapter -
25 R123525 1 Gasket, Oil Filter Header up to - 766852
26 R53108 1 Gasket, Starting Motor -
27 R72328 4 O-ring, Remote Oil Filter Tubes -
28 R89944 1 O-ring, Water Pump Inlet -
29 R61105 2 O-ring, Connector Tube to Timing Gear Cover -
30 T122075 2 O-ring, Oil Cooler to Housing -
31 R136495 2 Gasket, Oil Fill Cover -
32 R500374 1 Gasket, Oil Filter Header from 766853 -
TY6304 1 Sealant -
33 16-15005 6 O-ring -
34 16-01000 2 O-ring -
35 16-31001 1 O-ring -
36 052300400 1 O-ring -
37 11-31011 6 Gasket, Exhaust -
38 11-30013 1 Gasket, Exhaust Flange -
39 11-31401 1 Gasket, K26 Turbo Mounting -
40 11-21011 2 Gasket, Intake Port -
42 11-31012 1 Gasket -
43 11-11022 1 Gasket, Filler Neck Mounting -
45 11-10015 2 Thermostat Seal Ring -
46 11-11013 1 Gasket, Thermostat Cover Mounting -
47 11-11043 1 Gasket, Expansion Tank Connection -
48 16-19502 1 O-ring, 7/16" I.D. x 3/16" Nitrile -
P1066 12/18
6-0

49 16-14804 1 O-ring, 2" I.D. x 1/8" Nitrile -
50 16-19503 1 O-ring, 4-1/4" I.D. x 3/32" Nitrile -
52 15-09501 2 Sealing Washer, Copper, M22 -
53 11-31615 1 Gasket, Turbo/Exhaust Mounting -
55 16-21001 2 O-ring, 1-3/4" I.D. x 3/16" -
L1066A, M1066A1, A2, A3

1 R123543 1 Gasket -
2 R521439 6 Gasket -
3 R502814 1 Gasket -
4 R123226 2 Seal -
5 R123345 1 Gasket -
6 R123570 1 Gasket -
7 R123575 4 O-ring -
9 R501373 1 Gasket -
11 R123572 1 Gasket -
12 R123354 1 Gasket -
13 R501428 1 Gasket -
14 R75892 1 O-ring -
15 R97185 1 O-ring -
16 R61871 1 O-ring -
17 A4827R 1 Washer -
18 RE44574 1 Seal -
19 RE59810 1 Seal Kit -
20 R123273 1 O-ring -
21 R123417 1 Gasket -
22 R136516 1 Gasket -
R136515 1 Gasket -
23 R123501 1 Gasket -
24 R502864 1 Gasket -
25 R123525 1 Gasket up to -766852
26 R53108 1 Gasket -
27 R72328 4 O-ring -
28 R89944 1 O-ring -
29 R61105 2 O-ring -
30 T122075 2 O-ring -
31 R136495 2 Gasket -
32 R500374 1 Gasket from 766853 -
RY6304 1 Sealant -
35 16-31001 1 O-ring, 1-7/8" I.D. x 3/16" -
36 052300400 1 O-ring -
39 11-31615 1 Gasket, Turbo/ Exhaust Mtg. -
40 16-29502 2 O-ring, 2-1/4" I.D. x 1/8" -
P1066 12/18
6-1

L1066A, M1066A1, A2, A3 continued

42 11-31012 1 Gasket -
43 11-11022 1 Gasket, Filler Neck Mtg. -
46 11-11013 1 Gasket, Thermostat Cover Mtg. -
49 16-14804 1 O-ring, 2" I.D. x 1/8" Nitrile -
51 16-19501 2 O-ring, 4-1/2" I.D. x 1/8" -
53 11-15704 2 Gasket, Block-off/ Adapter Mtg. -
55 16-25701 1 O-ring, 2-7/8" I.D. x 3/16" -
56 16-29501 1 O-ring, 2-3/8" I.D. x 3/16" -
57 16-13101 2 O-ring, 2-1/2" I.D. x 1/8" -
58 11-29501 1 Gasket, Aftercooler Mtg. -
59 16-09601 2 O-ring, 17" I.D. x 1/8" -
60 16-09504 2 O-ring, 7-1/2" I.D. x 1/8" -
NL1066T, H1, H2, H3
•• RE526965 1 Gasket Set, Engine Overhaul (includes all keys, former #RE501456) -
1 R123543 1 Gasket -
2 R521439 6 Gasket -
3 R502814 1 Gasket -
4 R123226 2 Seal -
5 R123345 1 Gasket -
6 R123570 1 Gasket -
7 R123575 4 O-ring -
9 R501373 1 Gasket -
11 R123572 1 Gasket -
12 R123354 1 Gasket -
13 R501428 1 Gasket -
14 R75892 1 O-ring -
15 R97185 1 O-ring -
16 R61871 1 O-ring -
17 A4827R 1 Washer -
18 RE44574 1 Seal -
19 RE59810 1 Seal Kit -
20 R123273 1 O-ring -
21 R123417 1 Gasket -
22 R136516 1 Gasket -
R136515 1 Gasket -
23 R123501 1 Gasket -
24 R502864 1 Gasket -
25 R123525 1 Gasket up to -766852
26 R53108 1 Gasket -
27 R72328 4 O-ring -
P1066 12/18
6-2
NL1066T, H1, H2, H3 continued
28 R89944 1 O-ring -
29 R61105 2 O-ring -
30 T122075 2 O-ring -
31 R136495 2 Gasket -
32 R500374 1 Gasket from 766853 -
TY6304 1 Sealant -
L- M1066H

1 R504882 1 Gasket, Rocker Arm Cover -
2 R515030 1 Gasket, Intake Manifold -
3 R505480 1 Gasket -
4 R123226 2 Seal -
5 R505479 1 Gasket -
6 R123570 1 Gasket -
7 R516158 7 O-ring -
9 R124607 1 Gasket -
10 R521439 6 Gasket -
11 R123572 1 Gasket -
12 R123354 1 Gasket -
13 R501428 1 Gasket -
14 R75892 1 O-ring -
15 R97185 2 O-ring -
16 R61871 1 O-ring -
17 R63185 2 O-ring -
18 RE44574 1 Seal -
19 RE59810 1 Seal Kit -
20 R123273 1 O-ring -
21 R123417 1 Gasket -
22 R502954 1 Gasket -
23 R123501 1 Gasket -
24 R136495 2 Gasket -
25 R123525 1 Gasket -
26 R53108 1 Gasket -
27 R72328 4 O-ring -
28 R89944 1 O-ring -
29 R61105 2 O-ring -
30 T122075 2 O-ring -
31 R500374 1 Gasket -
32 16-15005 6 O-ring, 1/2" I.D. x 3/32" -
33 16-01000 2 O-ring, 3/4" I.D. x 3/32" -
34 16-31001 2 O-ring, 1-7/8" I.D. x 3/16" -
35 052300400 1 O-ring -
38 11-31615 1 Gasket, Turbo/ Exhaust Mtg. -
39 11-39501 1 Gasket, Coolant Port Adapter Mtg. -
41 11-31012 1 Gasket
P1066 12/18
6-3
L- M1066H continued
42 11-11022 1 Gasket, Filler Neck Mtg. -

43 11-11023 1 Gasket, Manifold To Expansion Tank -
45 11-11013 1 Gasket, Thermostat Cover Mtg. -
47 16-19502 1 O-ring, 7/16" I.D. x 3/16" -
48 16-14804 1 O-ring, 2" I.D. x 1/8" -
49 16-19503 1 O-ring, 4-1/4" I.D. x 3/32" -
50 16-19501 2 O-ring, 4-1/2" I.D. x 1/8" -
52 11-15704 2 Gasket, Block-off/ Adapter Mtg. -
54 16-25701 1 O-ring, 2-7/8" I.D. x 3/16" -
55 16-29501 1 O-ring, 2-3/8" I.D. x 3/16" -
56 16-13101 2 O-ring, 2-1/2" I.D. x 1/8" -
57 16-09504 2 O-ring, 7-1/2" I.D. x 1/8" -
58 16-09601 2 O-ring, 17" I.D. x 1/8" -
NL1066H4
•• RE527015 1 Gasket Set, Engine Overhaul (includes all keys, former #RE518148)
1 R504882 1 Gasket -
2 R515030 1 Gasket -
3 R505480 1 Gasket -
4 R123226 2 Seal -
5 R505479 1 Gasket -
6 R123570 1 Gasket -
7 R516158 7 O-ring -
9 R124607 1 Gasket -
10 R521439 6 Gasket -
11 R123572 1 Gasket -
12 R123354 1 Gasket -
13 R501428 1 Gasket -
14 R75892 1 O-ring -
15 R97185 2 O-ring -
16 R61871 1 O-ring -
17 R63185 2 O-ring -
18 RE44574 1 Seal -
19 RE59810 1 Seal Kit -
20 R123273 1 O-ring -
21 R123417 1 Gasket -
22 R502954 1 Gasket -
23 R123501 1 Gasket -
24 R136495 2 Gasket -
25 R123525 1 Gasket -
26 R53108 1 Gasket -
27 R72328 4 O-ring -
28 R89944 1 O-ring -
29 R61105 2 O-ring -
30 T122075 2 O-ring -
31 R500374 1 Gasket
P1066 12/18
6-4
pages added 9-1-09
GROUP 7 - GEAR AND ADAPTER PARTS
Gear Oil Cooler Heat Exchanged Units

L1066T
A-5005/ C-2541A

1 20-62500 1 Gear Oil Cooler -
2 16-10001 2 O-ring -
3 20-61039 1 End Cover 1-1/4" HB with drain -
4 20-61040 1 End Cover 1-1/4" Hose Barb without drain -
20-61038 1 End Cover 900 1-1/4" Hose Barb (units with wet exhaust elbow) -
7 23-61004 1 Lifting Eye/ Gear Oil Cooler Mtg. -
10 19-00056 1 Hose Clamp #56 -
11 41-01070 20" Hose 1-1/4" ID Wire Reinforced -
12 19-00020 2 Hose Clamp #20 -
13 27-19503 1 Tube -
P1066 12/18
7-1
pages added 9-1-09
Gear Oil Cooler Heat Exchanged Units

L1066A - H
A-5005/ C-2541Aver2

2 16-10001 2 O-ring -
3 20-61086 1 End Cover 1-3/4" HB with drain -
4 20-61087 1 End Cover 1-3/4" Hose Barb without drain -
20-61088 1 End Cover 900 1-1/4" Hose Barb (units with wet exhaust elbow) -
7 23-69607 1 Gear Oil Cooler Mtg. -
11 18-12511 1 Hose 1-3/4" ID x 3" -
12 19-00028 2 Hose Clamp #28 -
13 27-69601 1 Tube -
P1066 12/18
7-2
pages added 9-1-09
Gear Oil Cooler Keel Cooled Units

L1066T
A-4929A/ C-2529

2 10-12510 1 Adapter -
3 20-61089 1 End Cover, 900 2-3/8" Hose Barb -
4 16-10001 2 O-ring -
5 11-11043 1 Gasket -
P1066 12/18
7-3
Notes
P1066 12/18
7-4
GROUP 8 - BASE FRAME AND MOUNTING
Engine Lifting Eyes

1 R502329 1 Rear Lifting Eye -
2 19M7788 1 Capscrew -
3 T26508 1 Front Lifting Eye -
P1066 12/18
8-1
Engine Mounting L1066
SAE #2 Flywheel Housing
A-8904/ B-1739
A-8770, A-8889/ B-2237A

1 23-81001 1 Mounting Bracket, Engine R/H front -
2 23-81002 1 Mounting Bracket, Engine L/H front -
3 23-89601 2 Mounting Bracket, Rear Engine (tapped for jack screw) -
23-89602 2 Mounting Bracket, Rear Engine (not tapped) -
5 15-01000 4 Lock Washer M16 -
7 33-74801 4 Flexible Mount -
P1066 12/18
8-2
Base Frame with Hydrolastic Mounts

M1066T (3 Phase)
A-8359, A-8360 / B-7682

1 39-81668 1 Base Frame, Steel** up to s/n xxxx-41727
39-81669 1 Base Frame, Aluminum up to s/n xxxx-41727
39-89616 1 Base Frame, Steel from s/n xxxx-41728
39-89617 1 Base Frame, Aluminum from s/n xxxx-41728
2 23-81002 1 Bracket, Front Engine Mtg., Left Hand -
3 23-81001 1 Bracket, Front Engine Mtg., Right Hand -
5 15-01000 4 Lock Washer, M16 -
6 12-00913 4 Cap Screw, Hex Head, 5/8 -11 x 1 -1/2" -
8 15-00901 4 Flat Washer 5/8" USS -
9 33-81013 2 Hydrolastic Mount 500 lbs.* -
10 33-81015 2 Hydrolastic Mount 700 lbs. -
11 14-00511 8 Hex Nut 1/2 -13 -
15 12-00332 8 Capscrew, Hex Head, 3/8 -16 x 1" Grade 8 -
16 15-00307 8 Flat Washer, 3/8" Hardened -
17 21-00530 2 Plug, Hex Head, Brass 1/2 NPT -
* Note: Mounts listed are for units without front PTO and are stamped #16
on upper portion of housing. Mounts provided on applications with PTO
are stamped #17. Contact dealer or factory for part numbers
required. Have unit serial # available.
**39-81668 retained for fuel tank mounted emergency gen-sets. Check unit
build list by serial number.
P1066 12/18
8-3
Base Frame with Centerbonded Mounts

M99C2/ UCI274E 3 Phase
A-/ B-7689

1 39-89601 1 Base Frame, Steel -
39-89603 1 Base Frame, Aluminum -
5 15-01000 4 Lock Washer, M16 -
7 15-00901 2 Flat Washer, 5/8" USS -
8 15-00015 2 Head Washer -
9 33-81002 2 Centerbonded Mount 500 Lbs. -
10 15-00025 2 Tail Washer -
11 14-00912 2 Hex Nut, Nylock 5/8- 18 -
12 12-00550 4 Capscrew, Hex Head, 1/2 -13 x 3" -
13 15-00501 4 Flat Washer, 1/2" USS -
14 15-00016 4 Head Washer -
16 15-00026 4 Tail Washer -
17 14-00512 4 Hex Nut, Nylock 1/2 -13 -
21 15-00307 8 Flat Washer, 3/8" Hardened -
23 39-01002 1 Drip Pan (optional) -
P1066 12/18
8-4
Base Frame with Centerbonded Mounts

M99C2/ UCI274G 1 Phase
A-8688A/ B-7689
5 15-01000 4 Lock Washer, M16 -
7 15-00901 2 Flat Washer, 5/8" USS -
8 15-00015 2 Head Washer -
10 15-00025 2 Tail Washer -
11 14-00912 2 Hex Nut, Nylock 5/8- 18 -
12 12-00034 4 Capscrew, Hex Head, 5/8- 11 x 3- 1/2" -
13 15-01330 4 Flat Washer, 5/8" SAE -
14 15-00015 4 Head Washer -
16 15-00025 4 Tail Washer -
17 14-00912 4 Hex Nut, Nylock 5/8- 11 -
21 15-00307 8 Flat Washer, 3/8"/ M10 Hardened -
22 39-01002 1 Drip Pan (optional) -
P1066 12/18
8-5
M1066T, A1 (431PSL6202)
A-10620, A-10621/ B-8954

5 15-01000 4 Lock Washer, M16 -
8 15-00901 6 Flat Washer 5/8" USS -
11 14-00502 12 Lock Nut, Flanged 1/2- 13 -
15 12-00332 8 Capscrew, Hex Head 3/8- 16 x 1" (Grade 8) -
16 15-00307 8 Flat Washer, 3/8, M10 Hardened -
*Note: Mounts listed are for units without front PTO and are stamped
#16 on upper portion of housing. Mounts provided on applications with
PTO are stamped #17.
P1066 12/18
8-6
M1066A1, A2, A3, H (431PSL6204 to 6208)
A-10337, A-10968/ B-8954

5 15-01000 4 Lock Washer, M16 -
8 15-00901 6 Flat Washer 5/8" USS -
11 14-00502 12 Lock Nut, Flanged 1/2- 13 -
P1066 12/18
8-7

M1066A2, A3, H (431PSL6210)
A-10969, A-10970/ B-8954

5 15-01000 4 Lock Washer, M16 -
8 15-00901 6 Flat Washer 5/8" USS -
11 14-00502 12 Lock Nut, Flanged 1/2- 13 -
P1066 12/18
8-8
M1066H (433RSL4021)
A-10971, A-10972/ B-8954

5 15-01000 4 Lock Washer, M16 -
8 15-00901 6 Flat Washer 5/8" USS -
11 14-00502 12 Lock Nut, Flanged 1/2- 13 -
14 15-00803 12 Lock Washer, M10 -
16 15-00307 8 Flat Washer, 3/8/ M10 Hardened -
P1066 12/18
8-9
revised 4-4-14
Base Frame
NL1066T / UCI 274 Generator
A-8339A/ D-3180A
P1066 12/18
8 - 10
revised 3-10-14
Base Frame
NL1066T / UCI 274 Generator

1 39-81002 2 Side Rail, Modular Base Frame -
2 39-81014 1 Engine Support, Modular Base Frame -
3 39-61601 1 Support, UCI274 Generator, Modular Base Frame -
4 23-81035 1 Bracket, Front Engine Mtg. Right Hand -
5 23-81036 1 Bracket, Front Engine Mtg. Left Hand -
6 23-81037 2 Bracket, Engine Support -
9 14-00502 14 Lock Nut, Plain Flanged 1/2- 13 -
14 01643-31645 2 Flat Washer M16 -
15 14-01432 2 Hex Nut M16 x 2.0 -
17 15-01330 2 Flat Washer 5/8" SAE -
18 15-00015 2 Head Washer -
19 33-81002 2 Mount, Centerbonded 500 lbs. -
20 15-00025 2 Tail Washer -
21 14-00912 2 Hex Nut, Nylock -
23 15-01211 2 Flat Washer 3/4" -
24 15-85000 2 Head Washer -
26 15-85001 2 Tail Washer -
27 14-01212 2 Hex Nut, Nylock 3/4- 10 -
31 15-00307 8 Flat Washer 3/8", M10 Hardened -
P1066 12/18
8 - 11
added 4-7-14
Base Frame
NL1066H & NL1064H2 @60Hz
A-8339A/ D-3180-2A
P1066 12/18
8 - 12
added 4-7-14
Base Frame
NL1066H & NL1064H2 @60Hz

3 39-61601 1 Support, UCI274 Generator, Modular Base Frame -
14 01643-31645 2 Flat Washer M16 -
15 14-01432 2 Hex Nut M16 x 2.0 -
17 15-01330 2 Flat Washer 5/8" SAE -
18 15-00015 2 Head Washer -
20 15-00025 2 Tail Washer -
21 14-00912 2 Hex Nut, Nylock -
23 15-01211 2 Flat Washer 3/4" -
24 15-85000 2 Head Washer -
26 15-85001 2 Tail Washer -
27 14-01212 2 Hex Nut, Nylock 3/4- 10 -
31 15-00307 8 Flat Washer 3/8", M10 Hardened -
P1066 12/18
8 - 13
added 3-10-14
Base Frame
NL1066T / M363 Generator
A-8339A/ D-3180A
P1066 12/18
8 - 14
revised 3-10-14
Base Frame
NL1066T / M363 Generator

3 39-81046 1 Support, M363 Generator, Modular Base Frame -
14 01643-31645 2 Flat Washer M16 -
15 14-01432 2 Hex Nut M16 x 2.0 -
17 15-01330 2 Flat Washer 5/8" SAE -
18 15-00015 2 Head Washer -
20 15-00025 2 Tail Washer -
21 14-00912 2 Hex Nut, Nylock -
23 15-01211 2 Flat Washer 3/4" -
24 15-85000 2 Head Washer -
26 15-85001 2 Tail Washer -
27 14-01212 2 Hex Nut, Nylock 3/4- 10 -
31 15-00307 8 Flat Washer 3/8" / M10 Hardened -
P1066 12/18
8 - 15
GROUP 9 - ACCESSORIES & OPTIONAL EQUIPMENT
Crankshaft Pulley
A-10446, A-10447, A-10449, A-10448/ C-2723z

1 34-69501 1 Crankshaft Pulley 4-A x 8" -
34-69502 1 Crankshaft Pulley 3-A/B x 8" -
19M7811 6 Capscrew, Hex Head Flanged M10 x 1.5 x 90 mm (Dual Dampers) -
P1066 12/18
9-0
revised 6-17-15
MMC-44 Electric Clutch
A-10450, A-10451, A-10453, A-10452/ C-2235

1 10-60016 1 Housing, Electric Clutch SAE #5 C-Pad -
2 34-69512 1 Drive Assembly (Former #34-61455) -
3 34-60036 1 Electric Clutch, H-44 12V C - Spline -
34-60037 1 Electric Clutch, H-44 24V C - Spline -
4 12-00035 8 Capscrew, Socket Head 3/8-16 x 3/4" -
6 15-00404 4 Flat Washer 7/16" -
8 15-00321 6 Flat Washer 3/8" SAE -
9 12-20319 8 Capscrew, Socket Head 3/8-16 x 2-3/4" (for 40 mm spacer) -
12-20320 8 Capscrew, Socket Head 3/8-16 x 3-1/2" (for 2.23" spacer) -
12-20324 8 Capscrew, Socket Head 3/8-16 x 4" (for 3" spacer) -
10 15-00300 8 Flat Washer 3/8" -
11 00-61003 1 Grommet -
12 00-40025 1 Plug -
P1066 12/18
9-1
added 6-17-15
MMC-100 Electric Clutch
C-2235

1 10-60016 1 Housing, Electric Clutch SAE #5 C-Pad -
2 34-69517 1 Drive Assembly -
3 34-60097 1 Electric Clutch, MC-100 12V C - Spline -
34-60098 1 Electric Clutch, MC-100 24V C - Spline (Supercedes 34-60088) -
4 12-00035 8 Capscrew, Socket Head 3/8-16 x 3/4" -
6 15-00404 4 Flat Washer 7/16" -
8 15-00321 6 Flat Washer 3/8" SAE -
9 12-20319 8 Capscrew, Socket Head 3/8-16 x 2-3/4" (for 40 mm spacer) -
12-20320 8 Capscrew, Socket Head 3/8-16 x 3-1/2" (for 2.23" spacer) -
12-20324 8 Capscrew, Socket Head 3/8-16 x 4" (for 3" spacer) -
10 15-00307 8 Flat Washer 3/8" -
11 00-61003 1 Grommet -
12 00-40025 1 Plug -
P1066 12/18
9-2
revised 6-17-15
PTO Adapter Parts

L- M1066T, M99C2, & M1066A2 / L1066A (with single crank damper) M1066A1 & M1066A3
A-8611/ C-2235/B-1991

1 23-71001 1 Bracket, Front PTO Mounting SAE #5 -
2 34-69401 1 PTO Carrier SAE #8 -
3 32-81001 2 Dowel Pin -
7 31-69601 1 Spacer SAE #5 x 40 mm * -
31-69604 1 Spacer SAE #5 x 2.23" ** -
* For models: L-M1066T - M99C2-M1066A2

**For models: L1066A (with single crank damper) - M1066A1-A3
P1066 12/18
9-3
PTO Adapter Parts

L1066A (Single Damper), M1066A1 & A3
M1066H @ 1800 RPM
A-10437/ C-2235/B-1991

1 23-71001 1 Bracket, Front PTO Mounting SAE #5 -
2 34-69401 1 PTO Carrier SAE #8 -
3 32-81001 2 Dowel Pin -
7 31-69604 1 Spacer SAE #5 x 2.23" -
P1066 12/18
9-4
revised 6-17-15
PTO Adapter Parts

L1066A (Dual Dampers) & L1066H All - M1066H @ 1500 RPM
A-10437, A-10396/ C-2235/B-1991, C-2309, C-2394

1 23-71001 1 Bracket, SAE #5 -
2 32-81001 2 Dowel Pin 5/8" OD x 1-1/2" -
5 31-69603 1 Spacer, Damper Mounting -
6 RE57604 1 Crankshaft Damper, Viscous (Dual Dampers) -
7 34-69603 1 PTO Carrier SAE #8 -
9 R516648 1 Capscrew, Socket Head M20 x 2.5 x 70 mm Grade 12.9 -
10 R517237 1 Washer -
11 31-69602 1 Spacer, SAE #5 x 3" -
P1066 12/18
9-5
Updated 4-2-08
Hydraulic Pump Drive Assembly

Oil Supply from Oil Filter Adapter,
L1066T Keel Cooled
RGP6232

1 RE500825 1 Auxiliary Drive Assembly SAE A Pad, 9 Tooth Spline -
2 R134465 1 Gasket -
4 15-00007 2 Flat Washer, M12 -
5 21-69501 1 Male Elbow 900, M12 x 1.5 x 3/8 O-ring Face Seal -
(includes keys 7 & 14) -
6 N275799 1 Restriction Orifice -
7 16-69501 2 O-ring -
8 18-69603 1 Hose Assembly, 1/4" I.D. x 34" -
9 21-09506 1 Female Branch Tee M16 x 1.5 x 3/8 -37T (includes key 15) -
10 R96935 1 Gasket* -
11 R85145 1 Plate* -
12 12-00832 2 Capscrew, Hex Head M10 x 1.5 x 30 mm* -
13 15-00804 2 Wave Washer, M10* -
14 51M7040 1 O-ring -
15 51M7042 1 O-ring *For shipping -
P1066 12/18
9-6
Low Oil Level Switch/ Gauge
M1066T
A-8602/ C-5543

1 22-10004 1 Oil Level Switch/ Gauge -
2 23-71018 1 Bracket, Oil Level Switch Gauge Mounting -
3 12-00111 4 Capscrew, Hex Head, 1/4 -20 x 3/4" -
5 15-00111 4 Flat Washer 1/4" -
7 21-79604 1 Female Run Tee, Steel 3/8 NPT x 3/8 -37T -
8 27-09602 1 Tube Assembly, Low Oil Level Switch/ Gauge -
9 21-79501 1 Male Elbow 900 Steel 1/4 NPT x 3/8 -37T -
11 21-51045 1 Male Compression Fitting Brass 1/4" Tube x 1/4 HB -
12 41-01011 9 Hose 1/4" ID Push-on -
13 21-71045 1 Female Swivel Brass 1/4HB x 1/4 -45T -
14 21-14810 1 Male Elbow 45° Steel 1/8 NPT x 1/4 -37T (M1066T R.H.) -
15 00-40016 1 Strain Relief Connection 1/2 NPT -
P1066 12/18
9-7
NL1066T
A-8459A/ C-5692

5 15-00111 4 Flat Washer 1/4" -
7 21-79604 1 Female Run Tee, Steel 3/8 NPT x 3/8 -37T -
8 27-09602 1 Tube Assembly, Low Oil Level Switch/ Gauge -
9 21-79501 1 Male Elbow 900 Steel 1/4 NPT x 3/8 -37T -
11 21-51045 1 Male Compression Fitting Brass 1/4" Tube x 1/4 HB -
12 41-01011 9 Hose 1/4" ID Push-on -
13 21-71045 1 Female Swivel Brass 1/4HB x 1/4 -45T -
14 21-15710 1 Male Elbow 90° Steel 1/8 NPT x 1/4 -37T -
16 28-71002 1 Plate -
17 21-79501 1 Female Swivel M18 x 1.5 x 3/8- 37T -
18 16-09503 1 O-ring -
P1066 12/18
9-8

M1066A- H
A-10741/ B-8619

5 15-00008 4 Flat Washer M6 -
7 16-09501 1 O-ring -
8 21-09510 1 Female Swivel, Steel M22 x 1.5 x 3/8- 37T -
9 21-79604 1 Female Run Tee, Steel 3/8 NPT x 3/8- 37T -
10 27-09604 1 Tube, Low Oil Level Switch/Gauge -
11 21-70011 1 Male Elbow 90° Steel 1/2 NPT x 3/8- 37T -
12 21-51045 1 Male Compression Fitting Brass, 1/4" Tube x 1/4 HB -
13 41-01011 9 Hose, 1/4" ID Push-on -
17 21-17302 2 Spacer -
P1066 12/18
9-9

NL1066A- H
A-10661/ B-8621

5 15-00008 4 Flat Washer M6 -
7 16-09501 1 O-ring -
9 21-79604 1 Female Run Tee, Steel 3/8 NPT x 3/8- 37T -
10 27-09604 1 Tube, Low Oil Level Switch/Gauge -
13 41-01011 9 Hose, 1/4" ID Push-on -
14 21-71045 1 Female Swivel, Brass 1/4 HB x 1/4- 45T Push-on -
15 21-15710 1 Male Elbow, 90° Steel 1/8 NPT x 1/4- 37T -
16 28-71002 1 Plate -
P1066 12/18
9 - 10

M1066A- H Left hand
A-10930/ B-8625

5 15-00008 4 Flat Washer M6 -
7 16-09501 1 O-ring -
9 21-79514 1 Union Elbow 90° Steel 3/8- 37T -
13 41-01011 9 Hose, 1/4" ID Push-on -
15 21-15710 1 Male Elbow, 90° Steel 1/8 NPT x 1/4- 37T -
16 28-71002 1 Plate -
P1066 12/18
9 - 11
Air Intake Shut-off Valve (4" Intake)
L- M1066
A-10898/ B-8491A

1 03-29503 1 Valve, Intake Air Shut-off -
2 41-30400 2.5" Hose, 4" ID 4 Ply Silicone 350ºF SAE -
3 19-02048 2 Hose Clamp #48 -
P1066 12/18
9 - 12
Low Coolant Level Switch/ Gauge

L- M1066T & M99C2
A-8350/ C-4519

1 22-10003 1 Coolant Level Switch/ Gauge (Isolated Ground) -
2 23-09509 1 Gauge Bracket -
4 15-00008 2 Flat Washer, M6 -
5 14-04803 2 Hex Nut, Nylock, M6 x 1.0 -
6 12-20913 1 Capscrew, Socket Head, M12 x 1.75 x 30 mm -
7 15-04802 1 Lock Washer, High Collar M12 -
8 21-70011 1 Male Elbow, 900 Steel 1/2 NPT x 3/8- 37T -
9 21-00015 1 Male Elbow, 900 Steel 1/4 NPT x 3/8- 37T -
11 41-01020 10 Hose, 3/8" ID Push-on -
12 21-71044 1 Male Elbow, 90° Brass 1/4 NPT x 1/4- 45T -
13 21-71043 1 Male Elbow, 90° Brass 1/8 NPT x 1/4- 45T -
15 41-01011 10 Hose 1/4" ID Push-on -
16 00-40016 1 Strain Relief Connection, 1/2 NPT -
P1066 12/18
9 - 13
Updated 3-10-14
Low Coolant Level Switch/ Gauge

L1066A - M1066A1, A2, A3,
L- M1066H
A-10734/ B-8628a

1 22-10003 1 Coolant Level Switch/ Gauge (Isolated Ground) -
2 23-09509 1 Gauge Bracket -
4 15-00008 2 Flat Washer, M6 -
5 14-04803 2 Hex Nut, Nylock, M6 x 1.0 -
12 21-71034 2 Female Swivel, Brass, 3/8 HB x 3/8- 37T, Push-on -
13 41-01020 16" Hose, 3/8" ID Push-on -
14 21-71044 2 Male Elbow 90° Brass 1/4 NPT x 1/4- 45T -
16 41-01011 18" Hose 1/4" ID Push-on -
17 00-40016 1 Strain Relief Connection, 1/2 NPT -
19 19-43201 1 Adelle Clamp 1/2" ID -
P1066 12/18
9 - 14
Raw Water Flow Switch with Dry Exhaust

L1066T, M1066T
A-8516, A-9081, A-9402, A-8519/ B-8012

1 22-11004 1 Flow Switch 10 GPM 1 -1/4 NPT (M1066T) -
37-11006 1 Flow Switch 6 GPM 1 -1/4 NPT (L1066T) -
2 23-19501 1 Bracket, Flow Switch Mounting -
4 15-00701 2 Flat Washer M8 -
5 15-00702 2 Lock Washer Helical M8 -
6 14-00711 2 Hex Nut M8 x 1.25 -
7 19-19501 2 U-Bolt 1 -1/2" ID x 3/8 -16 S/S -
8 14-00302 2 Lock Nut, Plain Flanged 3/8 -16 -
9 21-15017 2 Male Connector Brass 1 -1/4 NPT x 1 -1/4" HB -
10 18-19501 1 Hose 1 -1/4" ID x 2 -1/2" (M1066T) -
11 19-01020 2 Hose Clamp #20 Extended Band S/S (M1066T) -
P1066 12/18
9 - 15
Raw Water Flow Switch
L1066A-H, M1066A1,2,3,H
A-10846, A-10848, A-11045, A-10847/ B-8629

1 37-16801 1 Flow Switch, Bronze 10 GPM 2" NPT (L1066A-H) -
37-16802 1 Flow Switch, Bronze 25 GPM 2" NPT (M1066A1,2,3,H) -
2 28-19501 1 Plate, 2" Flow Switch Mtg. -
3 23-19511 1 Clamp, 2" Flow Switch Mtg. -
7 12-00311 2 Capscrew, Hex Head 3/8-16 x 3/4" -
9 27-19517 1 Tube, Flow Switch Inlet 2" HB S/S -
10 21-15029 1 Male Connector, 2" NPT x 2" HB S/S -
11 18-26002 2 Hose 2" ID x 2-3/4" 4 Ply Silicone -
12 19-01032 4 Hose Clamp #32 -
13 21-19502 1 Male Connector, Copper 2" NPT x 1-3/4" HB (L1066A-H) -
21-15714 1 Male Connector, Copper 2" NPT x 1-5/8" HB (M1066A1,2,3,H) -
P1066 12/18
9 - 16
Raw Water Flow Switch
L1066T Keel Cooled
A-9127/ B-8640

1 37-11006 1 Flow Switch 6 GPM 1 -1/4 NPT (L1066T) -
2 23-19504 1 Bracket, Flow Switch Mounting -
7 19-19501 2 U-Bolt 1 -1/2" ID x 3/8 -16 S/S -
8 14-00302 4 Lock Nut, Plain Flanged 3/8 -16 -
9 21-15017 2 Male Connector Brass 1 -1/4 NPT x 1 -1/4" HB -
15 27-19603 1 Tube, Raw Water Discharge S/S
16 18-19501 2 Hose 1 -1/4" ID x 2 -1/2" -
P1066 12/18
9 - 17
12 Volt 40 Amp Alternator, Left Side Mounted
L1066T
A-8902/ C-4434

1 27060-78301-71 1 Alternator, 12 Volt 40 Amp -
2 23-89501 1 Alternator & Engine Mounting Bracket -
4 15-00701 5 Flat Washer, M8 -
5 14-04802 3 Hex Nut, Nylock, M8 x 1.25 -
6 23-70025 1 Tensioning Arm -
10 15-00201 1 Stud Washer, 5/16 -
11 34-69501 1 Crankshaft Pulley, 4-A x 8" -
13 15-00321 4 Flat Washer, 3/8" SAE -
14 40-01601 1 Drive Belt -
15 00-49602 1 Belt Guard, (see also application with hydraulic pump drive) -
P1066 12/18
9 - 18
24 Volt 40 Amp & 12 Volt 90 Amp Alternator

L1066T, Left side Mounting
A-10351/ B-8647

1 22-40278 1 Alternator, 24 Volt 40 Amp -
22-40332 1 Alternator, 12 Volt 90 Amp -
2 34-41019 1 Pulley 2-A/B x 3-5/8" ID -
3 23-89608 1 Bracket, Engine/ Alternator Mtg. -
5 15-00504 1 Flat Washer 1/2" SAE -
6 23-49602 1 Tensioning Arm -
8 14-04802 1 Nut, Hex Head Nylock M8 x 1.25 -
10 15-00202 1 Lock Washer Helical 5/16 -
11 15-00201 1 Stud Washer 5/16 -
12 34-69501 1 Pulley, Crankshaft 4-A x 8" -
15 40-05901 1 Drive Belt Set -
16 00-49602 1 Belt Guard, 2nd Small Frame Alternator -
20 15-00701 4 Flat Washer M8 -
21 22-40486 1 Cable #2 AWG x 43" 1/4" x 1/2" POS (not shown) -
22 22-40487 1 Cable #2 AWG x 49" 1/4" x 1/2" NEG (not shown) -
P1066 12/18
9 - 19
4420 14th Ave. NW., Seattle WA 98107
Tel: (206) 789-3880 • 1-800-762-0165 • www.northern-lights.com
Northern Lights and Lugger are registered trademarks of Northern Lights, Inc.
© 2018 All rights reserved. Litho USA.

Northern Lights m1066 Parts

Uploaded by

Document Informationclick to expand document information

Document Informationclick to expand document information

Copyright:

Available Formats

Northern Lights m1066 Parts

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Northern Lights m1066 Parts

Uploaded by

Copyright:

Available Formats

PARTS MANUAL

As of January 2011, U.S. EPA regulations require the

Copyright ©2016 Northern Lights, Inc.

L - Lugger propulsion unit Base Model #

Northern Lights turbocharged propulsion Northern Lights turbocharged industrial

Lugger Serial Number Generator Set Serial Number

Generator Set Serial Number

ALTERNATOR ASSEMBLY: M - NL668

5 KEY PART NUMBER QTY. DESCRIPTION SERIALNUMBER

0 185046210 1 Alternator Assembly 10 -

NOTE: a Arrows always point toward the front of the engine.

KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER

*Not available separately - see short block listing.

L- M1066H & NL1066H4

L- M1066H & NL1066H4

KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER

*Not available separately - see short block listing.

KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER

1 RE520385 1 Short Block Assembly (L-M-NL1066T, M99C2) -

RE520383 Short Block Assembly (L1066A, M1066A1,

2 RE522680 1 Short Block Assembly (L-M1066H and NL1066H4) -

Flywheel Housing SAE #2

KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER

Flywheel Housing SAE #3

KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER

For Dual Starter Applications

KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER

KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER

*Not for use on applications with dual starters

Flywheel SAE #11-1/2

KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER

*Used on applications with dual starters

Crankshaft and Main Bearings

KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER

Crankshaft Pulley and Damper

L- M1066T, M99C2, & M1066A2

KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER

L1066A, M1066A, M1066A1, A3, & M1066H @ 1800 RPM

KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER

Dual Crankshaft Pulley and Damper

L1066A Pleasure Craft, L1066H All & M1066H @ 1500 RPM

KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER

Crankshaft Pulley and Damper

NL1066H1, H2, H3, H4

KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER

A-10447, A-10449, A-10446, A-10448/ B-3732

KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER

Cylinder Liner Assembly and Connecting Rod

KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER

Cylinder Liner Assembly and Connecting Rod

L- M1066H & NL1066H4

KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER

•• RE516228 6 Piston Liner Kit (marked RE507758, includes keys #7-8) -

Timing Cover Plate

M- L1066T, M99C2, L1066A, A1, A2, A3

KEY PART NUMBER QTY DESCRIPTION SERIAL NUMBER

Timing Cover Plate