Study Master Technology Grade 9 Teacher S Guide

Technology
CAPS
Grade
9
Grade
11
Teacher’s Guide
Ria de Jager • Lin Bassett • Neel Ramdutt

Lynn Pocock • Barbara Munsami
SM_Technology_G9_TG_CAPS_ENG.indd 1 2013/07/02 1:58 PM

Study & Master
Technology
Grade 9
Teacher’s Guide
Ria de Jager • Lin Bassett • Neel Ramdutt

Lynn Pocock • Barbara Munsami
SM_Technology_G9_TG_TP_CAPS_ENG
Technology_Grade 9 Prelims.indd 1 promo.indd 2 2013/07/02 1:56
3:32 PM
cambridge university press
Cambridge, New York, Melbourne, Madrid, Cape Town,

Singapore, São Paulo, Delhi, Mexico City
Cambridge University Press

The Water Club, Beach Road, Granger Bay, Cape Town 8005, South Africa
www.cup.co.za
© Cambridge University Press 2013
This publication is in copyright. Subject to statutory exception

and to the provisions of relevant collective licensing agreements,
no reproduction of any part may take place without the written
permission of Cambridge University Press.
First published 2013
ISBN 978-1-107-25675-0
Editor: Fairuz Parker

Proofreader: Cheryl Knupp
Typesetter: Simon van Gend
Illustrators: Sara Jardine, Naeem Mohamed, Zedduo
Cover image: Panthera pardus, commonly known as a Leopard, © Doug Steakley/Gallo Images
/Getty Images
……………………………………………………………………………………………………………
Cambridge University Press has no responsibility for the persistence or
accuracy of URLs for external or third-party internet websites referred to in
this publication, and does not guarantee that any content on such websites is,
or will remain, accurate or appropriate. Information regarding prices, travel
timetables and other factual information given in this work are correct at
the time of first printing but Cambridge University Press does not guarantee
the accuracy of such information thereafter.
……………………………………………………………………………………………………………
notice to teachers
The photocopy masters in this publication may be photocopied or

distributed [electronically] free of charge for classroom use within the
school or institution which purchases the publication. Worksheets and
copies of them remain in the copyright of Cambridge University Press
and such copies may not be distributed or used in any way outside the
purchasing institution.
Acknowledgements
AAI/Fotostock SA: bowl/cup/plate p E40 and E41, yoghurt p E40 and E41, blood bags p E40
and E41, water bottles p E40 and E41; Bigstock: plastic bottles p E40 and E41, plastic gloves
p E40 and E41; Fairuz Parker: detergent bottles p E43 and E46, plastic containers p E43 and
E46, egg box p E43 and E46, plastic toys p E43, blister plastic p E43 and E46.
If you want to know more about this book or any other Cambridge University Press
publication, phone us at +27 21 4127800, fax us at +27 21 419-8418 or send an e-mail to
capetown@cambridge.org
Technology_Grade 9 Prelims.indd 2 2013/07/02 3:32 PM

Contents
Expanded contents pages iv
Section A: Introduction A1
Section B: Planning B1
Section C: Assessment C1
Section D: Teaching guidelines D1
Section E: Photocopiable resources E1
Section F: Documents F1

iv
Term Strand Module Unit Time Lesson Activities CAPs content, concepts and skills Assessment LB TF
allocation tasks page page
(weeks and
hours)
Technology_Grade 9 Prelims.indd 4
Term 1
1 Structures 1. Structures 1.1 Graphic com- Week 1 Lesson 1 Activity 1 First angle orthographic projection, Drawing 5 D3
munication (2 hrs) Activity 2 three different views 7 D3
Activity 3 8 D4
Lesson 2 Activity 4 Discuss line types, scale and Scaled 3D 9 D4
Activity 5 dimensions drawing 11 D4
Week 2 Lessons 3 Activity 6 More complex 3D objects in Drawing 12 D4
(2 hrs) and 4 Activity 7 orthographic projection with 13 D5
instruments
EXPANDED CONTENTS
Flight of stairs and wheel ramp in 3D
using isometric projection
Design brief
Plan of stair and ramp first angle
projection with scale, correct views,
line types, dimensions
1.2 Structures: Week 3 Lesson 5 Activity 8 Forces can be dynamic or static Solving 17 D5
Forces, strength (2 hrs) Activity 9 Loads can be even or uneven problems 17 D6
and properties Activity 10 Strength of materials under tension, answering 18 D6
compression, both, torsion questions
Self assessment
Lesson 6 Activity 11 Properties of materials Teacher 23 D7
Activity 12 Find the strongest design assesses 27 D7
Activity 13 Assessment informal: Analysing for Group work 29 D8
tension, compression, torsion Class discussion
Learning about materials and their Teacher
properties assesses
Homework worksheet, materials,
properties
Formal
Assessment
Task:
Mini-PAT 1
2013/07/02 3:32 PM
(weeks and
hours)
1 Structures 1. Structures 1.2 Structures: Week 4 Lesson 7 Activity 14 Discussion of scenario and possible Teacher 35 D9
Forces, strength (2 hrs) solutions assesses plan
and properties Week 4 Identification of roles in the group Peer
Teacher explains plan process,
business using hand out
Drawing up a business plan
Answering an advert
Lesson 8 Activity 15 Tendering process Teacher/ 36 D10
Listing of tasks for each role Project
discussion of factors influencing the Manager
solution of the problem
Teacher
Week 5 Lesson 9 Activity 16 Creation of ideas out of knowledge of Evaluation, 41 D15
(2 hrs) Activity 17 structures adaption 43 D15
Week 5 Sketches of two solutions
Look at sketches to evaluate and adapt
Lesson 10 Activity 18 Design brief and specifications Design Brief 43 D15
Activity 19 requirements and specifica- 43 D16
Flow chart requirements tions
Flow chart
Week 6 Lesson 11 Activity 20 Working drawings Drawing 43 D16
(2 hrs) first angle
Week 6 orthographic
projection
1 Structures 1. Structures 1.2 Forces, Lesson 12 Activity 21 Budgets Costing of 45 D16
strength and materials,
properties labour,
overhead costs
Week 7 Lessons 13 Activity 22 Making, working with tools, materials Building the 45 D16
EXPANDED CONTENTS
(2 hrs) and 14 following order of work model
Safe working practices
Working as a team
2013/07/02 3:32 PM
vi
(weeks and
hours)
1 Structures 1. Structures 1.2 Forces, Week 8 Lessons 15 Activity 23 Knowledge of a rubric design Design a rubric 46 D17
strength and (2 hrs) and 16 Evaluation skills Evaluation of
properties own project and
other teams
with RUBRIC
Week 9 Lessons 17 Activity 24 Knowledge of each member’s role presentation 47 D17
(2 hrs) and 18 Understanding of structures of project to
Understanding of drawings, artistic and tender board
working
EXPANDED CONTENTS
Week 10 Formal assessment
Term 2
2 Mechanical 2: Mechanical 2.1 Hydraulics 1 Lesson 1 Activity 1 Investigate a hydraulic and Revision 53 D23
systems and systems and and pneumatics (2 hrs) Activity 2 pneumatic system using two equal Experiments 55 D25
control control sized syringes Recording
Self-assessment Worksheets
Lesson 2 Activity 3 Investigate a hydraulic and Worksheets 55 D26
pneumatic system using two Obervation
different sized syringe Discussion
Lesson 3 Activity 4 Construct a simple hydraulic system Research 58 D26
Activity 5 Hydraulics Observation 59 D28
Investigation
Recording
2 Lesson 4 Activity 6 How a hydraulic jack works Evaluation 62 D29
(2 hrs) Activity 7 Working the hydraulic jack Observation 63 D29
Activity 8 Presentations 66 D32
Lesson 5 Activity 9 Draw a systems diagram 67 D33
Activity 10 68 D33
2.2 Pulleys 3 Lesson 6 Activity 11 Investigating pulleys Worksheets 75 D34
(2 hrs) Observation
Presentation
Lesson 7 Activity 12 Bicycle brake Recording 81 D35
Activity 1 3 Mechanical control system Drawing 83 D35
4 Lesson 8 Activity 14 Design a handout Designing a 86 D36
(2 hrs) handout
2013/07/02 3:32 PM
(weeks and
hours)
2 Mechanical 2: Mechanical 2.2 Pulleys Lesson 9 Activity 15 Gears Designing a 89 D37
systems and systems and handout
control control Lesson 10 Activity 16 Evaluation skills and design skills Investigation 90 D38
Worksheet
Lesson 11 Activity 17 Draw a 3D wooden object using single Drawing 91 D39
Activity 18 VP perspective texturing 93 D40
Use single VP perspective to draw an
inside view of the classroom
Formal
Assessment
Task:
Mini-PAT 2
6 Lesson 12 Activity 19 Investigation skills Investigation 95 D42
(3 hrs) Discussion
recording
Lesson 13 Activity 20 Design skills – sketches Sketching 95 D43
7 Lesson 14 Activity 21 Working drawings Drawing 97 D43

(2 hrs) Lesson 15 Activity 22 Make: Prototype working model Making 97 D44
and 16 Building
8 Lesson 17 Activity 23 Communication skills Presentations 97 D44
(1 hr) Project
portfolio
9 Formal Assessment
(1 hr)
EXPANDED CONTENTS
vii
2013/07/02 3:32 PM
Term Strand Module Unit Time Lesson Enabling CAPs Content, concepts Assessment tasks LB TF
viii
allocation tasks and skills page page
(weeks and
hours)
Term 3
3 Electrical 3. Electrical 3.1 Revision: Week 1 Lesson 1 Activity 1 Revision Revision 100 D47
systems systems and Component (2 hrs) Activity 2 Component symbols Observation 101 D48
and control control symbols Activity 3 Simple circuits Component symbols 102 D48
Activity 4 Ohm’s Law qualitatively Making simple circuits 103 D48
Activity 5 Ohm’s law 103 D49
Activity 6 104 D49
Activity 7 104 D51
Activity 8 105 D51
EXPANDED CONTENTS
Activity 9 105 D53
Activity 10 106 D53
Activity 11 106 D54
Activity 12 108 D54
3.2 Revision: Lesson 2 Activity 13 Research: Testing Ohm’s law Research 109 D55
Simple circuits Activity 14 Reading on graph Measuring 111 D55
3.3 Ohms law Activity 15 Calculate values Plotting on graph 112 D56
quantitatively Readings
3.4 Testing Ohm’s
law
3.5 Resistors Week 2 Lesson 3 Activity 16 Resistor colour codes Investigating resistor 116 D57
(2 hrs) Low value resistors colour codes
High value resistors
Lesson 4 Activity 17 Calculate values Calculation 117 D58
Activity 18 117 D58
3.6 Components Week 3 Lesson 5 Activity 19 Switches: Manual switches Types of switches, Diodes 121 D59
(2 hrs) Activity 20 Diodes and LED and LED 122 D59
Knowledge of transistors
Lesson 6 Activity 21 Transistors Building circuits 124 D59
Connect a simple transistor
circuit
Week 4 Lesson 7 Activity 22 Sensors – input devices Knowledge of sensors 125 D60
(2 hrs) Light dependent resistor – Observation
LDR
2013/07/02 3:32 PM
(weeks and
hours)
3 Electrical Electrical or 3.6 Components Lesson 8 Activity 23 Thermistor, touch or Observation 126 D60
systems electronic Activity 24 moisture detector, capacitors 126 D60
and control systems Activity 25 127 D60
Activity 26 127 D61
Activity 27 128 D61
Activity 28 128 D61
3.7 Simple Week 5 Lesson 9 Activity 29 Simple electronic circuits Draw 129 D62
electronic circuits (2 hrs) • LED, 470 ohm resistor, Make simple circuits
switch, and 4,5 V series
battery
• LDR, buzzer, 3 V series
battery
Lesson 10 Simple electronic circuits Draw 131 D63
• NPN transistor, buzzer Group work
or bell, thermistors, Assemble electronic
variable resistor, 1K ohm circuits
resistor, 6 V series battery
(or DC power supply or
photovoltaic panel)
• 6 V series battery, LED
470 ohm resistor, 1000 uF
capacitor switch
Short 131 D63
Practical
Assessment
Task:
Mini-PAT 3
Week 6 Lesson 11 Activity 30 Choose appropriate circuit to Investigate 134 D64
(2 hrs) solve the problem, need or Design
EXPANDED CONTENTS
want given in the scenario.
Incorporate into the design
ix
2013/07/02 3:32 PM
x
(weeks and
hours)
3 Electrical Electrical or 3.7 Simple Lesson 12 Activity 31 The design brief. Individual Design 135 D65
systems electronic electronic circuits drawing of circuit diagram Circuit diagram
and control systems Sketch in 3D showing the 3D sketch
device that will use the Suggest final solution
electronic circuit.
Final solution.
Week 7 Lesson 13 Activity 32 Plan for their device/model/ Working drawings 136 D65
(2 hrs) prototype first angle orthographic
Each team member draws a projection
EXPANDED CONTENTS
working drawing 3D exploded view
Lesson 14 Activity 33 Device/prototype/working Make model 137 D66
model
Showcase a viable solution
Scale and net
Show intelligent use of
available materials
Week 8 Lessons 15 Activity 34 Present their solution: Team presentations 137 D66
(2 hrs) and 16 sketches, artistic
impressions, working
drawings/plans, costing, and
their model
Week 9 Lessons 17 Activity 35 Each learner compiles Record of contributions 138 D67
(2hrs) and 18 a record of his/her own
individual contribution to
the task
Week 10 Summative assessment
(1 hr)
2013/07/02 3:32 PM
Term Strand Module Unit Time Lesson Activities CAPs Content, concepts and Assessment tasks LB TF
allocation skills page page
(weeks and
hours)
Term 4
4 Processing 4. Processing 4.1 Preserving 1 Lesson 1 Activity 1 Preserving metals –Theory Informal, observation 147 D69
metals (2 hrs) Activity 2 Painting and correction of 148 D71
Galvanising task
Lesson 2 Activity 3 Preserving metals – Practical Teacher assessment 148 D71
Electroplating of electroplating task
4.2 Indigenous 2 Lesson 3 Activity 4 Preserving food – Theory Correction of written 151 D72
technology: (2 hrs) Activity 5 Storing grain task 152 D72
preserving food Activity 6 Pickling 154 D73
Lesson 4 Activity 7 Preserving food – Practical Demonstration of 154 D73
Activity 8 Drying and/or salting drying or salting to 155 D73
preserve food
4.3 Processing 3 Lesson 5 Activity 9 Types of plastic and their uses Tabulation of 156 D74
plastic (2 hrs) Activity 10 Investigation: Identification of information 157 D74
plastic identifying codes and
sorting for recycling
Lesson 6 Activity 11 Properties of plastics Informal, observation 159 D74
Reduce –reuse – recycle and correction of
written activity
4.4 Re-use of 4 Lesson 7 Activity 12 Case study 1: Remanufacturing Discussion 165 D75
waste plastic (2 hrs) waste plastic into pellets for Drawing a systems
re-use diagram
Systems diagram: Draw a
systems diagram describing a
plastics recycling plant
Lesson 8 Activity 13 Case study 2: Moulding recycled Informal, observation 165 D76
Activity 14 plastic pellets into products and correction of 167 D77
EXPANDED CONTENTS
Activity 15 written task 167 D77
5 Lesson 9 Formal Case study 3: Plastics used in Tabulation of 168 D78
(2 hrs) Assessment modern motor cars. information
Task: Paragraph writing
xi
Mini-PAT 4
2013/07/02 3:32 PM
Term Strand Module Unit Time Lesson Activities CAPs Content, concepts and Assessment tasks LB TF
xii
allocation skills page page
(weeks and
hours)
4 Processing 4. Processing 4.4 Re-use of Lesson 10 Activity 16 Case study 4: Plastics around Discussion 173 D78
waste plastic Activity 17 the home Identification of a 173 D78
Activity 18 Problem identification: identify problem 174 D79
Activity 19 a need or want that can be Recording of 175 D79
satisfied by the making of a information
plastic item of their own design
6 Lesson 11 Activity 20 Sketch: sketch their plastic item Communication 176 D80
(2 hrs) Activity 21 using isometric projection on Isometric and first 178 D80
grid paper angle projection
EXPANDED CONTENTS
Plan: draw their plastic item drawings
using first angle orthographic
projection
Lesson 12 Activity 22 Skills development: practise the Making 179 D80
skills needed to manufacture Informal assessment
their plastic item – measure, – observation of skills
mark out, cut, bend and join.
Moulding is an optional extra
7 Lesson 13 Activity 23 Practical sessions: Working Making 180 D81
(2 hrs) Activity 24 safely, learners measure, mark Demonstration 180 D81
out, cut and bend the materials of team work and
for their plastic item and then making skills
assemble the product Teacher assessment
Lesson 14 Activity 25 Each learner compiles a record Communication skills 180 D81
of his/her term’s work including Teacher’s
extending the life span of metals assessment of
and food, properties and uses product and portfolio
of various plastics, the plastic
recycling strategy, the case
studies and the sketches and
plans for the product.
8 Summative year end Formal assessment
(2 hrs) examinations task under exam
conditions
2013/07/02 3:32 PM
Section A: Introduction
Curriculum and Assessment Policy Statement (CAPS) A3

Inclusivity A6
Time allocation per subject A10
Technology in the school curriculum A10
Requirements for Technology A15
SECTION A INTRODUCTION A1
A1

Welcome to Technology Grade 9. This course includes a Learner’s
Book and Teacher’s Guide that provide the core material you need to
cover the content required by the Curriculum and Assessment Policy
Statement for Grade 9 Technology.
In the Introduction (Section A) you will find information about
the core features of the National Curriculum and detailed advice on
the Technology subject in particular.
Assessment is covered in Section C and explains how and when
assessments should be done.
Section B (Planning) contains a detailed phase plan, teacher plan
(work schedule) and an exemplar of a lesson plan. The answers to all
activities can be found in Section D. These include rubrics and checklists
for formal and informal assessment of prescribed practical work.
Section E contains photocopiable worksheets, activities, rubrics
and exemplar assessments. In Section F you can file your copy of the
Curriculum and Assessment Policy Statement. You can also file your
own documents in this section.
As a teacher at the General Education and Training (GET) level,
your two main resources are:
• your expertise in the subject
• your teaching experience – knowing how to help learners master
the skills and knowledge of this subject.
Curriculum and Assessment Policy Statement

(CAPS)
The new Curriculum and Assessment Policy Statement (CAPS) makes
two core demands on you as the teacher:
• to follow a learning programme that enables learners to develop all
the skills, knowledge, values and attitudes relevant to Technology
• to have a sound, up-to-date knowledge of the content and methods of
your subject, and a clear understanding of its social relevance, so that
you can act as a guide, facilitator and subject expert in the classroom.
This textbook helps you to meet these demands in the following ways:
• it provides a structure for your teaching programme for the year
and a teaching plan (work schedule) that is in line with the CAPS
requirements
• it provides solutions to all the activities in the Learner’s Book
• it explains all the assessment requirements of the curriculum and
provides practical activities with their rubrics and checklists that
are required by CAPS
• it contains examples of generic rubrics, checklists and assessment
sheets that you can use or adapt for your assessment work
throughout the year.

General aims of the South African Curriculum
The National Curriculum Statement Grades R to 12 gives expression
to knowledge, skills and values that are regarded to be worth learning.
This statement will ensure that learners acquire and apply knowledge
and skills in ways that are meaningful to their own lives. In this
regard, the curriculum promotes the idea of grounding knowledge in
local context, while being sensitive to global imperatives.
The purpose of the National Curriculum Statement

Grades R to 12
The National Curriculum Statement aims to:
• equip learners, irrespective of their socio-economic background,
race, gender, physical ability or intellectual ability, with the
knowledge, skills and values necessary for self-fulfilment and
meaningful participation in society as citizens of a free country
• provide access to FET and higher education.
The principles of the National Curriculum Statement
Grades R to 12
The principles of the National Curriculum Statement are:
• social transformation
• active and critical learning
• high knowledge and high skills
• progression
• human rights, inclusivity, environmental and social justice
• valuing indigenous knowledge systems
• credibility, quality and efficiency.
These principles can be applied to your school context in the following
way:
Social transformation
What does social transformation mean in your classroom? Your
learners will come from families and communities that have been
affected in diverse ways by South Africa’s past. They will have many
different ideas about the kind of future career they want and the kind
of society they want to live in. In the learning programme that you
plan for the year, you need to provide opportunities for the learners to
analyse, research and come to understand the role that this particular
subject plays in shaping the kind of society we want to create in South
Africa and in offering them possibilities for their future.
For example: Create opportunities for learners to research and
discuss questions such as how many people in their families have
studied Technology and to what levels. How does access to Technology
education relate to access to different kinds of employment? What
factors influence people’s access to and success in the subject?
A4 SECTION A INTRODUCTION

Active and critical learning
What does this mean in your classroom? Many of the laws and
principles in Technology have been developed and formulated over
centuries.
You need to explain the background of how these laws and
principles were developed and the meaning and application of their
formulation. Make the learners aware that technological knowledge is
man-made solutions or ideas to solve problems.
For example: Ways of processing food is to make food last longer
and can change as new technologies become available.
High knowledge and high skills

What does this mean in your classroom? You, as a subject expert,
should inspire your learners with relevant knowledge and activities
that will encourage them to want to explore technology in depth.
Encourage them to relate what they learn to their lives outside school
and to possible future career paths. Strive to develop a high level of
knowledge and skills in this subject in all your learners.
For example: Relate the study of particular Technology topics
to future career paths, such as electrical, chemical and mechanical
engineering and electrical and telecommunications technology.
Where possible, create opportunities for learners to meet professional
practitioners in these and other relevant fields. Set projects that
challenge learners to apply their technology skills outside the school
context. Inform them about what they can expect to learn if they
follow these subjects in the FET and later on enrol for higher
education in related technology subjects.
Progression
What should this mean in your classroom? This Technology curriculum
contains material at the appropriate level to meet the criteria required for
Grade 9. If you plan a learning programme using this curriculum, you
will ensure that your learners progress appropriately through the levels of
knowledge and skills that the curriculum requires.
Human rights, inclusivity, environmental and social

justice
What should this mean in your classroom? In all activities that you
organise and facilitate, create opportunities to relate Technology to the
broader social goal of promoting human rights, environmental justice
and social justice. Take into account that some of your learners might
grapple with issues such as poverty, language and disability in their
daily lives. Encourage them to explore these issues in ways that relate
to this subject.
For example: Identify a social issue of relevance in the learners’
community and help them research and design a technology solution
to a community problem. This could relate to the availability of a
bridge to cross a river or to design a two-way switch for a gate or a
light in a passage.

Valuing indigenous knowledge systems
What should this mean in your classroom? This Technology
curriculum contains material that draws on indigenous knowledge
systems and encourages learners to take these systems into account
in their research and practical work. You should also draw on
the expertise in your subject that may be available in your local
community. Compile information about individuals and organisations
in your region that can support your classroom work by means of
relevant indigenous knowledge to which they have access.
Encourage learners to recognise sources of relevant indigenous
knowledge in their own communities, and to include these sources in
their research and practical work.
For example: People from indigenous cultures have always found
ways to preserve food.
Credibility, quality and efficiency

What should this mean in your classroom? The content of the
Technology curriculum has been reviewed by experts in their fields
of civil, electrical and mechanical engineering and covers all facets
required to prepare learners to go on to FET.
Qualities and skills of learners

The National Curriculum Statement aims to produce learners who are
able to:
• identify and solve problems and make decisions using critical and
creative thinking
• work effectively as individuals and with others as members of a
team
• organise and manage themselves and their activities responsibly
and effectively
• collect, analyse, organise and critically evaluate information
• communicate effectively using visual, symbolic and/or language
skills in various modes
• use science and technology effectively and critically, showing
responsibility towards the environment and the health of others
• demonstrate an understanding of the world as a set of related
systems by recognising that problem-solving contexts do not exist
in isolation.
Inclusivity
Inclusivity should become a central part of the organisation, planning
and teaching at each school. This can only happen if all teachers
have a sound understanding of how to recognise and address barriers
to learning and how to plan for diversity. We have included some
guidelines on how teachers can achieve this.

Inclusive education and training should:
• acknowledge that all children and youth can learn, and that all
children and youth need support
• accept and respect the fact that all learners are different and have
different learning needs, which are equally valued
• enable education structures, systems and learning methodologies
to meet the needs of the learner
• acknowledge and respect differences in children, whether due to
age, gender, ethnicity, language, class, disability, HIV status or any
other reason.
• maximise the participation of all learners in the culture and the
curriculum of educational institutions and uncover and minimise
barriers to learning.
What should this mean in your classroom? In this series of books,

the learners work together in groups and pairs, which gives them the
opportunity to learn from each other, as well as at their own pace.
The learning methodologies cater for learners with different learning
abilities. Gender is also addressed as both boys and girls are able to
participate in all the activities. Learners also have the opportunity to
learn about diversity within the subject matter covered.
Learners with physical barriers can work in groups or with a
partner so they can be assisted where necessary. The teacher must
therefore group learners with disabilities together with learners with
other disabilities or no disabilities so they can support each other.
Special needs
In many classrooms, learners with special needs require additional
attention. Some learners require very little attention while others need
more extensive help. As a teacher, be especially sensitive towards these
learners without drawing too much attention to the learners’ possible
barriers to learning.
Discretely make their fellow learners aware of the need to treat
each other with respect without exception. This vital life skill should
be engrained in all young people so that it becomes part of their
personalities for the rest of their lives. The information that follows
will assist you in addressing some of these special needs in your
classroom in an inclusive way. Be aware of these and other special
needs of learners in your classroom.
Partial sight or blindness: For partially sighted learners who find it

difficult to read text, you could enlarge the text by using a photocopy
machine. Also, ensure that these learners sit in the middle or at the
front of the class so that their poor eyesight does not become a barrier
to their learning.
Alternatively – and especially in group work – read the text
aloud to these learners. Remind the learners to read loudly, clearly
and slowly as partially sighted and blind learners rely heavily on their

memories. When doing experiments, these learners might not be able
to see results. Train a few fellow learners with excellent social skills to
convey results to their peers.
It is also a good idea to let these learners stay in the groups with
learners you have trained specially to help them.
Hard of hearing: Once again, these learners should sit in the front
of the class. When giving instructions, or when reading text to these
learners, the speaker or reader should face the learner directly and
speak loudly and clearly but without exaggerating. Learners who are
hard of hearing learn to lip-read very early in life.
Impaired social skills: The nature of these difficulties varies, but

could, in some cases, become a serious barrier to learning.
• Learners who are very shy or highly-strung might find class
presentation extremely stressful. Although you should encourage
them to develop this life skill, remember that you can never
change someone’s nature completely. Work gently with these
learners – their shyness or nervousness may be the result of
negative circumstances at home. Let them present their class
presentations in written form at first, and then move slowly as
the year progresses, at first letting them present their work to one
classmate only, then to a small group, and finally to the whole
class.
• Children with ADS (Attention Deficit Syndrome, also known as
ADD Attention Deficit Disorder) will find it extremely difficult
to work in groups or to sit still and concentrate for very long – in
some cases having to listen for two minutes is too long. Learners
with ADS could affect the class atmosphere and class discipline
in a negative way, and although everyone will agree that the
deficiency is no fault of their own, they should not be allowed to
ruin their fellow learners’ education.
The school should have a policy that parents must inform the school
confidentially if their child suffers from ADS. If learners have been
diagnosed, they could be on medication. It is essential that teachers
are informed; otherwise the learner could be branded as ‘extremely
naughty’, which would be unfair and result in inappropriate handling.
Teachers should be very careful not to judge a ‘naughty’ learner too
soon. ADS is quite common, and in some cases may not have been
diagnosed.
Look out for a learner who:

• finds it difficult or even impossible to concentrate
• frequently interrupts the teacher with irrelevant or seemingly
‘stupid’ questions
• fidgets all the time to the point of irritating peers
• jumps up frequently and asks to go to the bathroom (or
somewhere else) at inappropriate times
• shouts out answers or remarks when the class has been asked to
put up their hands
• is unable to deal with group work or pair sessions – these periods
are interpreted as a ‘free for all’
• shows signs of aggression when fairly disciplined
• argues with the teacher when asked to keep quiet.
Please note that:

• the disorder is more prolific among boys than among girls
• diet could play role in controlling the disorder – fast foods and
junk foods should be kept to a minimum.
Extreme poverty: This barrier to learning requires extreme sensitivity

from the teacher. If you know that there are one or more learners in
your class who come from poverty-stricken backgrounds, you could
handle the situation as follows:
Learners are often required to bring resources from home,
especially in practical learning areas like Technology. Some learners
may be unable to afford additional resource materials such as
magazines for research, rulers, calculators and mathematical sets. Keep
a supply of these items in your classroom without informing your
learners and unobtrusively give them to those learners you know have
difficulty in acquiring them. Be careful not to encourage ‘forgetters’ to
make use of this offer! You could ask community groups in your area,
such as churches, to provide support in collecting supplies of materials
for you to keep in your classroom.
The key to managing inclusivity is ensuring that barriers are
identified and addressed by all the relevant support structures within
the school community, including teachers, district-based support
teams, institutional-level support teams, parents and special schools as
resource centres. To address barriers in the classroom, teachers should
use various curriculum differentiation strategies such as those included
in the Department of Basic Education’s Guidelines for Inclusive
Teaching and Learning (2010).

Time allocation per subject
The instructional time in Grade 9 is shown in the table:
SUBJECT HOURS
Home Language 5
First Additional Language 4
Mathematics 4,5
Natural Sciences 3
Social Sciences 3
Technology 2
Economic Management Science 2
Life Orientation 2
Arts and Culture 2
TOTAL 27,5
The allocated time per week may only be used for the minimum
required NCS subjects as specified above. Should a learner wish to
take additional subjects, these will have to be done outside this time.
Technology in the school curriculum

Purpose
Technology education was introduced into the South African
curriculum in recognition of the need to produce engineers,
technicians and artisans needed in modern society and the need
to develop a technologically literate population for the modern
world. The subject stimulates learners to be innovative and develops
their creative and critical thinking skills. It teaches them to manage
time and material resources effectively, provides opportunities for
collaborative learning and nurtures teamwork. These skills provide a
solid foundation for several FET subjects as well as for the world of
work.
In the educational context, Technology can be defined as:
The use of knowledge, skills, values and resources to meet people’s
needs and wants by developing practical solutions to problems,
taking social and environmental factors into consideration.
Specific aims
Technology as a subject contributes towards learners’ technological
literacy by giving them opportunities to:
• develop and apply specific design skills to solve technological
problems
• understand the concepts and knowledge used in Technology
education and uses them responsibly and purposefully
• appreciate the interaction between people’s values and attitudes,
technology, society and the environment.

The intention is to introduce learners to the basics needed in Civil
Technology, Mechanical Technology, Electrical Technology and
Engineering Graphics and Design. Additionally, learners gain an idea
of the way engineers apply scientific principles to practical problems.
In addition, evaluation skills will be fostered and the introduction of
product design and production will be useful in other FET subjects
that use these skills – such as Consumer Studies and Design.
It is expected that Technology education will provide learners with
some experience to help them to make career-oriented subject
choices at the end of Grade 9.
Unique features and scope

Key issues to teach:
1. Problem solving using the design process
2. Practical skills
3. Knowledge and application of knowledge.
Technology will give learners the opportunity to learn:

• to solve problems in creative ways
• to use authentic contexts rooted in real situations outside the
classroom
• to combine thinking and doing in a way that links abstract
concepts to concrete understanding
• to evaluate existing products and processes, and to evaluate their
own products
• to use and engage with knowledge in a purposeful way
• to deal with inclusivity, human rights, social and environmental
issues in their tasks
• to use a variety of life skills in authentic contexts (such as decision
making, critical and creative thinking, co-operation, problem
solving and needs identification)
• to work collaboratively with others through practical projects,
using a variety of technological skills (investigating, designing,
making, evaluating and communicating) that suit different
learning styles.
At the same time, learners will be creating positive attitudes,
perceptions and aspirations towards technology-based careers.

Topics and core content areas in Technology
The table below indicates the main focus areas in the Technology
curriculum:
1. The design process skills (non-linear)
• Investigation skills
• Design skills
• Making skills
• Evaluation skills
• Communication skills
2. Structures
3. Processing of materials
4. Mechanical systems and control
5. Electrical systems and control
6. Technology, society and the evironment
• Indigenous technology
• Impact of technology
• Bias in technology
There are four core content areas in Technology in Grades 7–9. These
are:
Structures Processing Mechanical Electrical
systems and systems and
control control
NB: All electric circuits must be battery powered in the GET Band – Max 9V DC
These four content areas form the basis of the four strands that
must be done each year in every grade. Where possible in the senior
phase, the learner should engage in projects that integrate processing,
structures and systems and control. The recommended approach
will be to introduce the required knowledge followed by practical
work in which the knowledge is applied. In all cases, the teaching
will be structured using the design process as the backbone for the
methodology. Some of these elements will be assessed formally each
term. As learning progresses, learners must be made aware of the
interrelationship between technology, society and the environment.
Wherever applicable, learners should be made aware of different
coexisting knowledge systems. They should learn how indigenous
cultures have used specific materials and processes to satisfy needs,
and become aware of indigenous intellectual property rights. Learners
should be able to consider the impact of technology, both positive and
negative, on people’s lives. Learners should be made aware of bias in
technology and be able to express opinions that explain how certain
groups within society might be favoured or disadvantaged by products
of technology.
The importance of design in Technology education

No product has ever been manufactured that did not undergo
development through design. Technology education is an introduction
to a range of careers that work in similar ways. All tend to use the

design process as they develop solutions to problems, needs or wants.
The country needs informed, critical consumers and producers of
knowledge.
A key element to teach is the ability to design.
With many similar products on the market, design excellence is a
key element in attracting consumers.
Examples of careers that use design:

Civil engineering – designing a Dietician – designing a diet to
bridge combat malnutrition and obesity
Architecture – designing a house Mechanical engineering –
Textile design – developing a designing a support system for
textile for a specific purpose the roof of a stadium
Electrician – designing the
electrical wiring for a lamp
Designers need to have...

• an understanding of the problem, need or opportunity
• knowledge of the design process
• knowledge of types and properties of suitable materials, and how
to use them optimally
• the ability to calculate the quantities and costs of the materials
needed
• knowledge of the conventions/building codes
• an ability to sketch initial ideas on paper
• the ability to draw working drawings in sufficient detail for the
task
• the practical skills required to create a solution
• the ability to work safely using appropriate tools
• the ability to adhere to health precautions
• the ability to present the solution effectively to the client/
customer.
Teaching methodology (how tasks will be

approached)
As learners progress through a task, they must be taught the associated
knowledge and skills needed to design and create a solution.
Knowledge is important BUT the learners must show that they
can use the knowledge, and not just memorise it.
The design process (Investigate, Design, Make, Evaluate,
Communicate – IDMEC) forms the backbone of the subject and
should be used to structure the delivery of all learning aims. Learners
should be exposed to a problem, need or opportunity as a starting
point. They should then engage in a systematic process that allows
them to develop solutions that solve problems, rectify design issues
and satisfy needs.
Investigate
Investigation in this subject involves finding out about contexts and
needs, investigating or evaluating existing products in relation to key

design aspects and performing practical tests to develop understanding
of particular aspects of the content areas or determining a product’s
fitness-for-purpose. While investigating, learners should be provided
with opportunities to explore values and attitudes and develop
informed opinions that can help them to make compromises and
value judgements. Investigation can happen at any point in the design
process. It should not be seen as something that must be completed
before design begins.
Designing, making and evaluating.

These skills should not be seen as separate – they are inter-related.
Evaluation skills, for example, are used to choose ideas. At this
level, learners should be introduced to key aspects of design. These
should be used to evaluate both existing and designed products
against predetermined criteria.
When making, learners should be encouraged to continue to
reflect on their progress against these criteria and to modify their
solutions based on problems encountered.
As learners progress they should be able to demonstrate increasing

accuracy and skill, better organisation and safer working practices.
Criteria for teaching and assessing design features:

• originality and aesthetics
• value for money/cost effectiveness
• fit-for-purpose and suitability of materials
• ease of manufacture
• safety and ergonomics
• environmental impact
• bias towards or against a group.
Communication
Communication should also be seen as integral to the overall process.
Learners should be recording and presenting progress in written and
graphical forms on an on-going basis. Their presentations should show
increasing use of media, levels of formality and conventions as they
progress through the phase.
Technology develops valuable problem-solving skills that will
benefit every learner in many life contexts.
Note on drawing: The Grade 9 learner must be able to identify and

explain a problem, need or opportunity from a given real-life context.
In Grades 7–9 Technology, drawing is separated into three fields:

• free-hand sketches in the design stage
• working drawings in the making stage, using formal draughting
techniques in line with conventions
• artistic impressions in the communication stage, using artistic
techniques including perspective, texture rendering, shading,

colours and shadows in order to advertise the product to potential
users.
NB: Perspective drawing here is purely artistic and has no link to

the method of linking the perspective to the working drawing using
formal construction lines. In Technology, learners draw both technical
AND artistic graphics.
Time allocation for Technology

The teaching time for Technology is two (2) hours per week. As this
subject involves practical work, 60 minutes of the two hours should
be one continuous period for practical work, e.g. one double period
comprising two periods of 30 minutes.
Schools using alternative period lengths, or a cycle system, must
ensure that all subjects get their correct time allocation and that
sufficient time is allocated for practical sessions.
Requirements for Technology

1. Each learner must have:
• an approved textbook
• a 72-page A4 workbook/exercise book (In secondary schools
learners may require two books per year.)
• stationery, including a basic mathematical set (drawing
instruments), pencil, eraser, ruler and set squares
2. There must be a designated teaching venue with a Technology
teacher.
3. Technology rooms must be secure, with doors that lock, and
with burglar-proofing if possible. Enough cupboards should be
available to store and lock away all resources.
4. It is the responsibility of the school to provide each learner with
the minimum tools and material to meet the needs of the subject
(see Section D for possible tools and resources) and to develop the
teacher’s appropriate knowledge and skills.
5. Enabling tasks: Activities used to teach and then practise specific
skills in preparation for a more advanced task – sometimes also
called resource tasks. These tasks are assessed informally.
6. Mini-PAT: A short Practical Assessment Task that makes up
the main formal assessment of a learner’s skills and knowledge
application during each term. It may be an assignment covering
aspects of the design process, or it may be a full capability task
covering all aspects of the design process (IDMEC).

Note: The curriculum for Grade 9 has been described very
specifically to ensure that all the learners cover the same work in all
schools across the country before graduating to secondary schools.
Some limited variations will be developed by the various textbook
authors.
The curriculum for Grade 8 has some sections described
fairly specifically while other sections give a lot of freedom for the
innovation expected from textbook authors.
The Grade 9 learners have to be able to ‘identify a problem,
need or opportunity’ in a given context. Consequently the
curriculum for Grade 9 is non-specific and textbook authors have
free reign to develop ideas that suit the given content.

Section B: Planning
Teacher plan B3
Lesson preparation B3
B1

Planning
Teachers are involved in different levels of planning for each subject.
These different levels of planning make up the learning programme
for that subject.
A learning programme consists of a subject framework, work
schedules and lesson preparations.
Teacher plan (work schedule)

The teacher plan specifies the scope of learning and assessment for
the three grades in a phase of the GET band. An overview of the
knowledge areas and topics for Technology in the GET phase appears
on pages iv–xii of this Teacher’s File.
The Curriculum and Assessment Policy Statement (CAPS)
specifies the core knowledge and concepts to be covered during the
GET phase, as well as the amount of time in hours and weeks to be
devoted to each topic.
Lesson preparation
A lesson preparation is a more detailed plan for a particular section
of work, a period of time during the year or a particular lesson. It
describes what learning is going to take place, and how it will take
place. In addition to the information in the work schedule, it explains
how the activities and assessments will take place as well as the use
of resources. The lesson preparation also refers to prior and future
learning.
You will need to carry out your own lesson preparation for your
class.
Your lesson preparation will indicate when and how you will
introduce each activity, each section of new knowledge, each
assessment activity, and so on, using and expanding the information
from the work schedule. We have included a blank lesson preparation
form in Section E: Photocopiable resources, and an example of a
completed lesson preparation in this section, to help you with your
planning.
SECTION B PLANNING B3

Exemplar of Lesson Plan Grade 9
Term 3: Week 7 – Lesson 13 and 14
Teachers name:
Grade: 9 Time: 2 hours Date:
Focus: Electrical Systems and Control
Content, concepts and skills:
Making skills
• Plans: working drawings
• The learners produce plans for their device/model/prototype using first angle orthographic
projection. The plans should include a 3D ‘assembly’ drawing in exploded view showing how the
model fits together.
• Each team member draws a working drawing of the design OR an aspect of the design.
• Make: device /prototype/working model
• The model must showcase a viable solution to the problem. It should be to scale and neat, and show
intelligent use of available materials.
Prior knowledge: Next week:
• Investigate the situation and the nature of the need so that an Communication skills
appropriate circuit can be chosen to solve the problem, need or want • Team presentations:
given in the scenario. Each team is given five
• A given circuit must be incorporated into the design of a device that will minutes to present
use the electronics to address the problem, need or want. their solution in the
The design brief: form of sketches,
• Each learner writes his/her suggestion for the design with specifications artistic impressions of
and constraints. the solution, working
Sketches drawings/plans, costing
• Each learner draws the circuit diagram. Each learner produces a sketch and their model.
in 3D showing the device that will use the electronic circuit .
• Teams meet and examine the individual suggestions to decide on a final
solution.
Teacher’s activities: Learners’ activities:
Learners need to use their prior knowledge to sketch, design and produce Activity 26
the product.
Refer back to first angle orthographic projection to sketch their plans. Activity 27
Assist learners that do not have the necessary skills yet.
Plans should include a 3D ‘assembly’ drawing.
Learners can share the different parts of the working drawing.
Learners make the device/prototype/working model
The model must showcase a viable solution to the problem. It should be to
scale and neat, and show intelligent use of available materials.
Resources:
(Resources will differ according to the Mini-Pat learners is going to do. The textbook will give you the
resources required.)
Planned assessment:
(In this term the learners need to do a full project portfolio, so all aspects of the Mini-PAT will be
formally assessed. Look in the Teacher’s File for assessment tools.)
Inclusive teaching and learning: (Barriers, remedial and extension activities)
Divide learners into different groups of abilities to assist each other during the Mini-PAT.
Teacher reflection:
B4 SECTION B PLANNING

Exemplar of recording sheet
Note different methods to calculate the 40% SBA (final assessment).
Grade Term 1 Term 2 Term 3 Term 4 SBA Practical Theory Final

Class Examination
Mini-PAT
Test 1
%
Code
Mini-PAT
Test 1
%
Code
Mini-PAT
Test 1
%
Code
Mini-PAT
%
Maximum marks
70
30
100
70
30
100
70
30
100
70
100
40
20
40
100
Date
Learner names
SECTION B
PLANNING
B5
2013/07/02 3:32 PM
Section C: Assessment
Informal or daily assessment C3

Using group and pair work C4
Formal assessment C6
Assessment tools C11
Programme of formal assessment C12
C1

Assessment
Assessment is a continuous planned process of identifying, gathering
and interpreting information about the performance of learners, using
various forms of assessment. It involves four steps:
1. generating and collecting evidence of achievement
2. evaluating this evidence
3. recording the findings
4. using this information to understand and thereby assist the
learner’s development in order to improve the process of learning
and teaching.
Assessment should be both informal (assessment for learning) and

formal (assessment of learning). In both cases regular feedback should
be provided to learners to enhance the learning experience.
Assessment is a process that measures individual learners’
attainment of knowledge (content, concepts and skills) in a subject
by collecting, analysing and interpreting the data and information
obtained from this process to:
• enable the teacher to make reliable judgements about a learner’s
progress
• inform learners about their strengths, weaknesses and progress
• assist teachers, parents and other stakeholders in making decisions
about the learning process and the progress of the learners.
Assessment should be mapped against the content, concepts, skills and

aims specified for Technology. In both informal and formal assessments
it is important to ensure that in the course of a school year:
• all of the subject content is covered
• the full range of skills is included
• a variety of different forms of assessment are used.
Informal or daily assessment
Assessment for learning has the purpose of continuously collecting
information on learners’ achievements that can be used to improve
their learning. Informal assessment is a daily monitoring of the
learners’ progress.
This is done through observations, discussions, practical
demonstrations, learner-teacher conferences, informal classroom
interactions, etc. Informal assessment may be as simple as stopping
during the lesson to observe learners or to discuss with learners how
learning is progressing. Use informal assessment to provide feedback
to the learners and to inform planning for teaching. Do not view
informal assessment as separate from learning activities taking place
in the classroom. The results of the informal daily assessment tasks are
not formally recorded unless the teacher wishes to do so. Learners or
teachers can mark informal assessment tasks. Self-assessment and peer
assessment actively involves learners in assessment.
SECTION C ASSESSMENT C3

This is important as it allows learners to learn from and reflect on
their own performance. Informal assessment also helps learners to
take responsibility for their own learning and for the learning of
their peers. In this way they develop a sense of self-discipline and
commitment to each other’s wellbeing.
The results of daily assessment tasks are not taken into account
for promotional and certificate purposes. Use informal, on-going
assessments to structure the acquisition of knowledge and skills and as
a precursor to formal tasks in the Programme of Assessment.
Using group and pair work

Many teachers in South Africa work in overcrowded classrooms,
which makes learning difficult. You can overcome some of these
problems by getting a class to work in groups. Practical work is
normally done in groups, while many activities lend themselves to
work in pairs. Smaller groups are easier to handle and learners will also
start to feel more positive about themselves.
Teamwork is an important aspect of learning skills and
constructing knowledge. Sharing the workload and being aware of
personal contributions to the community is important for every
learner. In a group, the different roles and responsibilities people
take on are essential to the success of the activity. At the GET level,
learners should already become aware of the roles and responsibilities
that are likely to be combined in ‘professional’ teams working in your
particular subject areas in the real working world.
Setting up
Certain learning tasks are better approached through a whole class
session; others lend themselves to group work. Working in pairs and
in groups of three to six learners, learners have a chance to express
themselves more often than when they are part of a class of forty or
more. They learn to work in a team, helping each other freely when
their knowledge or skill is strong, and being helped when it is weak.
Some learners might be too shy to ask a question in front of a whole
class but feel at ease asking a small group of friends.
Group work
There are many ways of organising learners into groups. Here are some
ideas:
• Language groups: If you have learners with different home
languages, you can put the speakers of each language into their
own language group. Same-language groups enable all the learners
to develop their understanding of a new concept in their own
language. At other times you can create mixed language groups.
Learners working in their second language or third language can
be helped with translation and have a greater chance to contribute
than they would in a large class.
• Ability groups: There are times when it is useful to divide
learners into groups according to how well they achieve in the
C4 SECTION C ASSESSMENT

learning area. The top achievers in the class are grouped together,
the average learners form a group, and the slowest learners are
grouped together. Top achievers can do enrichment activities
while you attend to the slower learners.
• Remediation groups: When you have finished assessing some
aspects of the learners’ work, you may often find a few learners
from different groups with the same problem. There may be a new
concept they haven’t quite grasped, or a few learners may have
been absent at the same time while you were dealing with new
work. You can then group them together temporarily while you
help them sort out the problem.
• Mixed-ability groups: These groups work well on their own while
you circulate between them. Vary the members of these groups so
that learners have experience in working with different classmates.
For instance, new groups can be formed each time a new unit of
work is started.
Guidelines for using group work

• When planning group work, you should decide on the
composition of each group and not always leave it to learners to
cluster together with those they work with most easily.
• Divide tasks fairly among the members of each group and each
member must understand his/her role.
• Give the learners clear and concise instructions.
• Define the work to be done clearly so that the group can go ahead
without constantly referring to you.
• Learners must be settled and attentive when instructions are
given.
• You must monitor progress at all times and should take into
consideration not only the end result, but also focus attention on
how the group has interacted and progressed through each step.
This will be possible if you circulate amongst the groups and give
information and guidance where and when it is required.
• Allow time for feedback so that learners have an opportunity to
present evidence of their progress at the end of a session.
• Regular reminders of time limits and what progress should have
been made at a particular stage are valuable when facilitating
group work.
• Place groups as far apart as possible so that they enjoy a sense of
privacy. Allow a certain amount of interaction as this often assists
learners in solving problems or coping with complex areas.
Pair work
Pair work is easier to control than group work, particularly in large
classes where it is difficult to re-arrange the seating. It is a very
useful strategy for task-based teaching as it frees the teacher to be a
facilitator, support guide and evaluator.

Pair work also allows for differentiation: pairs that work faster can be
given extra tasks; some pairs can be given more challenging tasks; in
mixed ability pairing, one partner can assist the other.
Solving problems related to pair and group work

• Noise can become a problem. Differentiate between ‘good
learning noise’ and ‘disruptive chatter’. Firmly remind learners
that they might be disturbing neighbouring classes and that they
should keep their voices down.
• Certain learners dominate a group, while others are idle and not
actively involved. Each individual must understand his or her role
or task, which should be constantly monitored. Use the report-
back to assess each learner’s involvement and progress.
• Learners may not like the partners they are paired or grouped
with. There is no quick-fix solution to this problem. You must,
however, use your knowledge of the learners and avoid grouping
personalities or characters that are likely to clash.
Formal assessment
All assessment tasks that make up the formal programme of
assessment for the year are regarded as formal assessment. Formal
assessment tasks are marked and formally recorded by the teacher for
progression and certification purposes. All formal assessment tasks
are subject to moderation for the purpose of quality assurance and to
ensure that appropriate standards are maintained.
Formal assessment provides teachers with a systematic way of
evaluating how well learners are progressing in a grade and in a
particular subject.
Examples of formal assessments include tests, examinations,
practical tasks, projects, oral presentations, demonstrations and
performances.
The formal assessment requirements for Technology are as follows:
• Formal assessment for Technology will consist of the mini-
Practical Assessment Tasks and pen and paper tests or
examinations.
• At least 40 out of the 70 mini-PAT marks per term must be
attributed to practical work.
• Tasks done by learners for formal assessment purposes should be
monitored by teachers at all times.
• Work done ‘off-campus’ outside the direct control of the teacher
should normally not form part of the formal assessment record.
• The end of year promotion mark will comprise 40% school
based assessment (SBA) and 60% (mini-PAT 20% and
examination 40%) end of year examination.

Formal Assessment in Technology – Grades 7, 8 and 9
INFORMAL FORMAL ASSESSMENT : TERM MARKS
DAILY
ASSESSMENT Practical Task and Theory Test/Examination TOTAL
Enabling
Mini-PAT Term Test/Examination Term Mark
Tasks
Term 1 70% 30% 100%
Term 2 70% 30% 100%
0%
Term 3 70% 30% 100%
Term 4 70 marks = 100% No Test 100%
CASS Component: 40% Final Examination Component: 60%
Continous Assessment: Combined Mini-PAT: 20 Examination Promotion
Promotion Test and Mini-PATs 40 40
Mark Term 1 + Term 2 + Term 3 + T1 + T2 + T3 + T4
Term 4 40 100
10 + 10 + 10 + 10 5+5+5+5
This breakdown is in line with the FET practical subjects where the
PAT mark is included as part of the final examination component. In
FET, the PAT mark contributes 1/3 of the final exam mark, i.e. 25
out of 75.
The above breakdown ensures that Technology in the GET band
retains its focus on practical aspects. However, since GET Technology
is not specialising, as happens in FET, there are four mini-PATs that
need to be added together in equal portions to provide the practical
examination component. As with the FET practical subjects, the
combined mini-PAT marks contribute 1/3 to the final exam mark, i.e.
20 out of 60.
The forms of assessment used should vary and be age- and
developmental level-appropriate. The design of these tasks should
cover the content of the subject and should include a variety of tasks
designed to achieve the theoretical and practical objectives of the
subject.
Formal assessment tasks form part of a year-long formal
Programme of Assessment in each grade and subject, and should be
adapted to meet the needs of inclusivity where necessary.
Control tests and examinations

Control tests and examinations are written under controlled
conditions within a specified period of time. Questions in tests
and examinations should assess performance at different cognitive
levels with an emphasis on process skills, critical thinking, scientific
reasoning and strategies to investigate and solve problems in a variety
of scientific, technological, environmental and everyday contexts.
Examinations papers and control tests in Technology Grade 9 should
adhere to the weighting of cognitive levels given in the table on the
next page. A detailed description of the cognitive levels follows.

RECALL UNDERSTANDING APPLICATION ANALYSE SYNTHESISE
EVALUATE
ROUTINE DIAGNOSTIC STRATEGIC INTERPRET CREATE
Low Order Middle Order Higher Order
30% 40% 30%
Mini-Practical Assessment Task (Mini-PAT)

Definition: a set of short practical assessment tasks that make up
the main formal assessment of a learner’s skills and application of
knowledge during each term. It may be an assignment covering aspects
of the design process, or it may be a full capability task covering all
aspects of the design process (IDMEC). It is composed of a variety of
forms of assessment suited to the range of activities that make up a
mini-PAT.
Purpose: a mini-PAT is intended to formalise the practical component
of Technology contextualised within a knowledge focus. Practical
activities should make up at least 40% of a Mini-PAT’s mark
allocation.
• The mini-Practical Assessment Task is designed to give learners the
opportunity to develop and demonstrate their levels of ability (i.e.
capability) as they progress through the task’s activities.
• Each mini-PAT focuses primarily on one of the knowledge foci
of Technology (viz. structures, mechanical systems and control,
electrical/electronic systems and control and processing), but may
be integrated and may target more than one knowledge focus.
• These tasks are structured according to the design process. Note
that this is not a linear process happening in a fixed sequence.
• Assessment in a mini-PAT need not cover all aspects of the design
process each term.
• A mini-PAT is an extended formal assessment task and must be
planned with other school activities.
The Mini-PAT makes up 70% of each term’s assessment. Practical

work must make up more than half of the marks.

The table below provides a guide for the mini–PAT per term per grade:
TERM 1 TERM 2 TERM 3 TERM 4
Capability task
GRADE 7 • Mini-PAT: • Mini-PAT: • Mini-PAT: • Mini-PAT:
Mechanical systems Structures Electrical/ Processing
and control Investigate + Design Structures/ Design + Make
Design + Make + Make Mechanisms
Investigate + Design
+ Make + Evaluate +
Communicate
Structures/ Impact of Technology Mechanical systems Electrical systems
Mechanical systems Processing and control/ and control
and control Investigate + Design Structures Design + Make
Communicate + + Make Investigate + Design
Design + Make + Make + Evaluate +
Communicate
Structures Mechanical systems Mechanical systems Processing
Communicate + and control and control Design + Make
Design + Make Investigate + Design Investigate + Design
+ Make + Make + Evaluate +
Communicate
• A learner must present the full design process once as a mini-

Practical Assessment Task in term 3 of each grade. This meets the
requirement of one project per subject per annum.
• The preferred tool to be used to assess learner performance in a
mini-Practical Assessment Task is an analytical rubric.
• Teachers will assess skills and values using analytical rubrics, which
should have clear descriptors for each level. This means that a
descriptor should say why an achievement is deemed to be, say,
‘meritorious’ or ‘elementary’.
• Schools must take responsibility for providing resources (both
tools and materials) needed during the mini-PAT.
• Learners must complete the mini-PATs for formal assessment
under teacher supervision.
• Teachers will assess the mini-PATs formally.
Tests
• A standardised test makes up 30% of each term’s assessment.
• A test for formal assessment should cover a substantial amount
of skills and content and should be set as follows:
—— Grade 7 – 45 minutes
—— Grades 8 and 9 – 60 minutes.
• The mark for tests is not prescribed but should be determined by
the teacher taking into account the volume of the content covered
and the time available. Testing in Technology will be limited to
ONE test each in terms 1, 2 and 3. This may take place either
just before or just after the mini-PAT, and must be planned in the
school assessment programme.

Examinations
• All examinations must include questions that integrate knowledge
and values with design process skills.
• In Technology the final end of year exam comprises 60% of the
learners’ promotion mark and should be set out as follows:
Grade Time allocation Mark weighting

7 60 minutes 60 marks
• The content assessed at the end of the year is based on the year’s
work as specified in the CAPS document for the grade. However,
prior knowledge from a previous grade may be necessary to
interpret and answer some of the questions in the higher grade.
Type of questions for pen and paper test

• The value of memorising by rote learning has little weight in
a subject requiring innovation, creativity and problem-solving
skills. The ability to think laterally and to develop original and
appropriate solutions is a key element in learning Technology.
• Learners should be able to investigate using a variety of sources,
demonstrate their ability to draw in a specific style, write a design
brief, give specifications and constraints, select appropriate
materials for a model, plan the sequence of manufacture of a
product, evaluate a design objectively, analyse a system using
systems diagrams and communicate their solutions using a range
of techniques.
• Questions that integrate knowledge, skills and value have more
value in Technology than a mere recall of knowledge facts.
The use of case studies

• Case studies are used to bring reality into the classroom.
• The intention should be to show learners that Technology is a
subject that is close to the way the world works.
• Case studies can be used both to develop and to assess a
technological skill (drawing for example), knowledge concepts and
values.
Assessment tools
Checklists
Checklists consist of separate statements describing how the teacher
can expect the learners to perform in a particular task. These
statements are the criteria that the learners must meet to succeed.
Rubrics
Rubrics are a combination of rating codes and descriptions of
standards – that is, what the learner must do, the level of competence,
and so on – to be rated with a particular code. The rubric describes

the range of acceptable performance in each band of the rating scale.
Rubrics require teachers to know exactly what the learner must
achieve – the level of competence, and so on – to meet the particular
outcome being assessed.
To design a rubric, you need to decide on the following:
• What is the outcome that you are aiming at?
• What kind of evidence should be collected?
• What are the different parts of the performance that will be
assessed?
• What different assessment instruments best suit each part of the
task?
• What knowledge should the learners demonstrate?
• What skills should learners apply, or what actions should they take?
It is crucial that you share the criteria in the rubric for the task
with the learners before they do the required task. The rubric clarifies
both what the learners should do and what they should be learning as
they carry out the task. It becomes a powerful tool for self-assessment.
When the learners have completed the task and you are assessing
their performance, you need to be sure that:
• each learner is assessed only once for each criterion within the
rubric
• you add comprehensive comments where necessary for later
moderation purposes.
Rubrics and checklists in Technology

The generic rubrics and checklists are in Section E: Photocopiable
resources. Modify them for your needs and use them as a guideline to
help you develop rubrics specifically for your activities and projects.
Programme of Formal Assessment

The Programme of Formal Assessment is designed to spread formal
assessment tasks in all subjects in a school throughout a term and for
the whole year. In addition to daily assessment (informal assessment),
teachers should develop a year-long formal Programme of Assessment
for Grade 9.
The learner’s performance in this Programme of Formal
Assessment will be used for promotion purposes to Grade 10.
Assessment is school-based.
The marks achieved in each of the assessment tasks that make up
the Programme of Formal Assessment must be reported to parents.
End-of-year examination
The end-of-year examination papers for Grade 9 will be internally
set, marked and moderated, unless otherwise instructed by provincial
Departments of Education. The internally set, marked and moderated
examination will consist of two papers. The table on the next page
shows the weighting of questions across cognitive levels and the
specification and suggested weighting of the content for Grade 9 end-
of-year examinations across two papers.

Content weighting for tests and examinations: Grades 7–9
Investigate, design, make, Structures, Processing, (Technology, Society and the
evaluate and communicate Mechanical and Electrical/ Environment)
Electronic Systems and Indigenous/Impact/Bias
Control
Design Process Skills: Knowledge: Values and Attitudes:
50% 30% 20%
NB: The above weighting for assessment should guide the approach
to teaching in Technology. Most of the knowledge will be acquired
purposefully during the development of design process skills. For
example, learners will investigate required knowledge aspects, and will
evaluate the possible impact on society or the environment.
Recording and reporting

Recording is a process in which the teacher documents the level
of a learner’s performance in a specific assessment task. It indicates
learner progress towards the achievement of the knowledge and skills
as prescribed in the Curriculum and Assessment Policy Statements.
Records of learner performance should provide evidence of the
learners’ conceptual progression within a grade and their readiness
to progress or be promoted to the next grade. Records of learner
performance should also be used to verify the progress made by
teachers and learners in the teaching and learning process.
Reporting is a process of communicating learner performance to
learners, parents, schools and other stakeholders. Learner performance
can be reported in a number of ways. These include report cards,
parents’ meetings, school visitation days, parent-teacher conferences,
phone calls, letters, class or school newsletters, etc. Teachers in all
grades report in percentages for the subject. The various achievement
levels and their corresponding percentage bands are shown in the table
below.
CODES AND PERCENTAGES FOR RECORDING AND REPORTING

RATING CODE DESCRIPTION OF COMPETENCE PERCENTAGE
7 Oustanding achievement 80—100
6 Meritorious achievement 70—79
5 Substantial achievement 60—69
4 Adequate achievement 50—59
3 Moderate achievement 40—49
2 Elementary achievement 30—39
1 Not achieved 0—29
Note: The seven point scale should have clear descriptions that give
detailed information for each level. Teachers will record actual marks
for the task by using a record sheet and report percentages for the
subject on the learner’s report card.

Moderation of assessment
Moderation refers to the process that ensures that the assessment
tasks are fair, valid and reliable. Moderation should be implemented
at school, district, provincial and national levels. Comprehensive and
appropriate moderation practices must be in place for the quality
assurance of all subject assessments. All Grade 9 tasks are internally
moderated. The subject head or head of department for Technology at
the school will generally manage this process.
Assessment taxonomy
The next table provides a possible hierarchy of cognitive levels that the
teacher can use to ensure tasks include opportunities for learners to
achieve at various levels and tools for assessing the learners at various
levels.
Knowledge Understand Apply Evaluating Analyzing Synthesising

Recall
30% 40% 30%
LOW MIDDLE HIGH
Count Classify Change Breakdown Arrange Appraise
Define Compare Compute Differentiate Combine Conclude
Identify Convert Construct Discriminate Compile Contrast
Label Discuss Demonstrate Investigate Construct Critique
List Distinguish Draw Relate Create Criticise
Match Define Illustrate Separate Design decide
Name Describe Predict Formulate evaluate
Outline Estimate Relate Generalise Grade
Point out Explain Solve Generate Justify
Quote Generalise Use Group Interpret
Recite Give examples Integrate Support
Repeat Illustrate Organise Recommend
Reproduce Infer Summarise
Select Interpret
State Match
Trace Paraphrase
Plan
Restate
Rearrange
Rewrite
Select
Summarise
Translate

Summary of assessment
observation marking oral

schedules memoranda presentation demonstration
checklist test
rubrics tools types examination
assessment
teacher method project
group
practical research
peer self
investigation

Introduction
Section D: Teaching Guidelines
TERM 1
Module 1: Structures
Unit 1.1 Graphic communication........................................................................... D5
Unit 1.2 Structures: Forces, strength and properties..................................... D7
Formal assessment task: Mini-PAT 1............................................................... D11
TERM 2
Module 2: Mechanical systems and control
Unit 2.1 Hydraulics and pneumatics.................................................................. D31
Unit 2.2 Pulleys.....................................................................................................D44
Formal assessment task: Mini-PAT 2............................................................D53
TERM 3
Module 3: Electrical systems and control
Unit 3.1 Revision: Component symbols.............................................................D61
Unit 3.2 Revision: Simple circuits.....................................................................D68
Unit 3.3 Ohm’s Law..............................................................................................D70
Unit 3.4 Action research: Testing Ohm’s Law................................................D70
Unit 3.5 Resistors................................................................................................. D72
Unit 3.6 Components........................................................................................... D73
Unit 3.7 Simple electronic circuits.................................................................... D76
Formal assessment task: Mini-PAT 3............................................................ D78
TERM 4
Module 4: Processing
Unit 4.1 Preserving metals..................................................................................D86
Personal and
Unit social well-being
4.2 Indigenous lessonsPreserving food.......................................
technology: page XXX D88
Unit 4.3 Processing
Physical education lessons plastic.
. ................................................................................D91
page XXX
Unit 4.4 Re-use of waste plastic.......................................................................D92
Creative arts: Performing arts pages XXX
Formal assessment task: Mini-PAT 4............................................................D95
Creative arts: Visual arts pages XXX
D11

1
TERM
During this term you will revise pneumatics and hydraulics and do some practical
applications using syringes. You will do research on force transfer and on Pascal’s
principle. You will take a closer look at the hydraulic press and the hydraulic jack.
This term you will investigate pulleys and a variety of mechanical control systems,
and revise the interactions of different gears. You will investigate a situation so
that an appropriate machine can be designed to solve the problem and produce
appropriate sketches.
D2
Technology_Grade 9_TG Mod 1.indd 2 2013/07/02 3:32 PM

Module
UnitStructures
1
1
Unit 1.1 Graphic communication
Week 1
You will facilitate learning about first angle orthographic projection,
investigate three dimensional objects on paper and look at the three
different views when drawing. Learners will also become familiar with
the different line types, scales and dimensions.
What you will need for Week 1:

• drawing paper
• drawing pencils
• squared grid paper (see Section E)
• drawing instruments
• isometric grid paper (see Section E).
Lesson 1 LB p. 4
Discuss with the class what graphic communication in Technology is
about. Refer to the Study & Master Technology grades 7 and 8 learner’s
books.
Discuss terms such as front view, side view and top plan view.
ACTIVITY 1 Draw an L-shape in first angle

orthographic projection LB p. 5
Individual
Work through the drawings step-by-step and discuss the layout.
ACTIVITY 2 Drawing orthographic projections

LB p. 7
Individual
Guide the class through the process of drawing a cube in first angle
projection.
Ask the learners to draw an H-shape. Give the class squared grid
paper to draw the different views. Let them draw the H-shape using
instruments.
UnIT 1.1 MODULE 1 TERM 1 D3

Let the learners draw the different views of Figure 1.9. They may
have to complete this exercise as homework if there is not enough
time in class.
ACTIVITY 3 Extension/homework LB p. 8
Individual
1. Give the learners squared paper and let them draw an

orthographic projection of Figure 1.10.
2. a) = E
b) = A
c) = C
d) = B
e) = F
f) = D
Lesson 2 LB p. 9
ACTIVITY 4 Line types LB p. 9
Class
Work through the descriptions of the different lines and their uses.
Discuss the need for scale when required to do drawings. Explain
carefully the difference between scaling up and scaling down.
ACTIVITY 5 A scaled 3D drawing LB p. 11

Individual
Let the learners practise drawing by drawing the table using 1:5 ratio.
Let them use the dimensions described in the Learner’s Book.
Lesson 3 LB p. 12
ACTIVITY 6 A scaled 3D drawing LB p. 12
Individual
Discuss dimension lines and how to use them.

Give the class isometric grid paper. Let the learners measure your
table. Remind them how to convert to draw to scale.
Week 2
The learners will draw 3D objects in orthographic projection using
instruments. They will draw up a design brief with specifications for a
given design problem.
Lesson 4 LB p. 13
Remind the learners about the purposes of a design brief and work
through the rubric on page 14 in the Learner’s Book with them
D4 SECTIOn D TEACHING GUIDELINES

carefully so that they understand exactly how they are going to be
assessed and what the criteria are.
ACTIVITY 7 Draw a plan LB p. 13

Individual
Once the learners have read and understood the checklist, they can
begin to produce the design brief. Use the rubric to assess their design
briefs and the working drawings that they will have produced.
Let them use the checklist for the design brief.
Unit 1.2 Forces, strength and properties
Week 3
Learners will find out more about the forces acting on structures, the
strengths and properties of materials when acted on by forces and the
properties of various construction materials.
Divide the class into groups of three to carry out the activities.
If time is a constraint, then allocate half of the groups to one activity
and the other half to the next activity.
Ensure that the groups carry out the experiments scientifically
and record their results. Each group must allocate a speaker to present
their findings to the class.
Lesson 5 LB p. 15
Discuss with the class the difference between a static and a dynamic
load. Let the class provide their own examples.
Discuss the idea of internal and external forces within a structure.
ACTIVITY 8 Self-assessment LB p. 17
Group
1. All forces are dynamic.
2. The see-saw will be in equilibrium.

3. Static – a load that cannot change

Dynamic – a load that changes because of a moving force
4. Structure’s own weight – static
Moving traffic on a bridge – dynamic
5. Static – high rise buildings, pot full of soil
Dynamic – bridges, road flyovers
6. Buckle, fracture and distort
7. These are forces inside the structure – internal
Forces outside the structure – external
8. When forces cancel each other out
ACTIVITY 9 Testing heavy loads LB p. 17

Group
Learners follow the instructions in the Learner’s Book to build a

bridge and do some tests. They record the findings of the tests and
interpret these findings. They will reach the following conclusions:
• the highest deflection occurs at the centre of the beam
• the most dangerous place for it to stop is the centre of the bridge.
ACTIVITY 10 Strength of materials under the

action of forces LB p. 18
Group
This can be demonstrated by you or conducted in groups, depending

on time constraints.
Let the learners follow the instructions in the Learner’s Book to
complete the activity. They will reach the conclusion that a beam is
stronger on its edge.
When looking at the pattern designs in Figure 1.25 on page 19 in the

Learner’s Book, the learners will reach the conclusion that the lattice
is the strongest. The designs all use triangulation and support because
this strengthens the beam bridge.
Look at and discuss the various examples of bridges on page 19 in
the Learner’s Book.
In Figure 1.30 (LB p. 20) the stiffest beam section is the second
one, which is placed on its side and not bending.
InFORMAL ASSESSMEnT Analyse for tension,

compression and
torsion LB p. 22
Pair
1. Member AB
2. Tension
3. The points X and X would move apart

4. Member CB
5. Points X X would cross over one another
6. A general rule would be to ask yourself, “What would happen to
the member if it broke? Would the two ends move apart or cross
over each other?”
7. Good under tension: EF
Good under compression: ED, DF
8. We use cross-bracing to support the members
9. Triangulation
10. Tension
Lesson 6 LB p. 23
Show the learners a range of different materials, such as cardboard,
paper, a piece of concrete, wood, brass, steel, iron, copper and ask
them to describe the examples, discussing their qualities or properties.
Then go through the questions on page 23 in the Learner’s Book
with respect to the different materials.
ACTIVITY 11 Materials and their properties

LB p. 23
Group
Divide the learners into groups of three and explain carefully how to
proceed. The instructions are in the Learner’s Book.
As a group assessment, the learners must complete the activity and
then as a class, discuss their findings.
ACTIVITY 12 Homework LB p. 27
Individual
Let the learners complete Activity 12 for homework. You can mark
this yourself or let the learners mark each other’s homework.
Picture A: Elephants Tensile strength: This is the strength
tugging needed to pull a material apart by
breaking the atoms.
Picture B: Bicycle chain Tensile strength: This is the strength
needed to pull a material apart by
breaking the atoms.
Picture C: Boy’s reaction Conductivity: Electricity can easily flow
to heat from candle through this material.
Picture D: Panel being Malleability: This is when a material can
formed be pressed into shape without breaking.
Picture E: Brass pins on Conductivity: Electricity can easily flow
plug through this material.
Picture F: Hammer hitting Malleability: This is when a material can
material into shape be pressed into shape without breaking.

Picture G: Saw cutting Hardness: This is when a material will not
wood break when hitting something else.
Picture H: Elephants Compressive strength: This is the
pushing towards each strength the material has to resist being
other squeezed.
Picture I: Filing a piece of Hardness: This is when a material will not
metal break when hitting something else.
Picture J: Making wire Ductility: This is when a material can be
drawn out without breaking.
Picture K: Hammer hitting Toughness: This is when a material will
nail not break when hitting something else.
Picture L: Boy bending Toughness: This is when a material will
rod not break when hitting something else.
ACTIVITY 13 Different building materials LB p. 29

Individual
Learners look at the different cross sections of the houses and

complete the table.
House 1 Materials Function
wooden poles framework
reeds covering roof
natural fibres joining
sand, dung,tar sealing, flooring
window glass protection, light
sods build walls
ant heap, linseed/ox blood flooring
House 2 saplings framework
grass covering roof
mud, clay, cow dung sealing, flooring
House 3 bricks walls
glass protection, light
plastic roofing
cement walls
stones walls
wood walls, beams
Safety procedure LB p. 32
In groups, let the learners come up with ten safety rules when working
in the Technology room. This activity should not take longer than ten
minutes for the learners to brainstorm. As a class read through the
safety rules and ascertain whether they came up with any other rules.
Week 4
Guide the learners through the tender process so that they understand
what is required of them in the Mini-PAT.

Lesson 7
Formal Assessment Task: Mini-PAT 1 LB p. 33
Topic: Structures
Task 1: Simulation
Group
Divide the class into groups. Discuss the different roles that members
of the group must fulfil. Each group must choose a member to fulfil
the different roles.
Discuss with the learners concepts such as tendering, a business
plan, credit, investors, risk, and competition. Use an example with
which the learners are familiar, for example, setting up a tuck shop at
school. Look at the advantages of a business plan when establishing
a tuck shop. It is essential that the learners understand the principles
underlying the creation of a small business.
The learners must work in the groups in which they will function
for the rest of the term. Each group must start thinking about their
business plan and making notes, which will aid them in compiling
their business plan.
ACTIVITY 14 Advert LB p. 35
Group
Let the groups read through the activity and answer the questions in
writing. This could be used as part of their assessment.
Peer assessment – each group must swop their answers with
another group and assess their responses.
Possible answers
1. The Msunduzi Municipality
2. To supply manufacture and erect ‘Y’ type passenger shelters at
various sites within the Msunduzi Municipality
3. Minimum CIDB Contractor Grading of 2CE and/or 2GB or
higher
4. Supply Chain Management Unit Offices, 5th floor, AS Chetty
Building, 33 Church, St, Pietermaritzburg from 12h00 on
Thursday, 21 July 2011
5. R136,80
6. To show that you are genuinely interested in tendering
7. No
8. To prevent fraud/invalid cheques
9. 12h00, Thursday, 11 August 2011
10. 90 days commencing from the closing date of tender
11. BEE is Black Economic Empowerment, which redresses
the inequalities of the apartheid era by giving previously

disadvantaged South African citizens (black Africans, coloureds,
Indians and some Chinese) economic opportunities previously
not available to them.
12. An SMME is a small, medium or micro enterprise
13. Why would the municipality expect businesses to support BEE/
SMMEs?
Let the learners swop their answers with another group and assess
their responses. Discuss the advertisement as a class.
Discuss the tender process with the class. Provide each group with
a tender form (see page E5).
The tender process

Photocopy and hand out to the learners pages E20 and E21 about the
tender process.
Any business wanting to tender must also join the local
municipality’s data base. An example of part of the form is included
(see page E3).
A letter of appointment (see page E7) from the client has also
been included so that each team can have a copy for their file. It
outlines briefly what is required of each team.
Discuss with the class the problem facing the community of
Jabulani. In their groups the learners must now allocate a specific role
or roles (depending on the size of the group).
Once the group has decided on the allocation of roles, each
member must be very clear as to his/her role within the group. Each
member of the group must make a list of his/her tasks and hand it
to the Project Manager. These must be kept in a file under a separate
section for each member.
Put up the careers available in the field of building construction.
The learners can read through these. Emphasise that different careers
cater for different skills and interests.
The group needs to discuss factors that will affect their solution to
Jabulani’s problem.
Give each team a handout about the tender process and a Letter
of appointment. You may find these documents in Section E.
Lesson 8 LB p. 36
ACTIVITY 15 Role description LB p. 36
Individual
Let the learners create a list of tasks that must be fulfilled in the role
he/she has been allocated. Let the learners chat to people in their
community to find out more about the responsibilities of the different
roles. Assist those learners who need help.

Careers in construction
You may create a poster so that this information can be displayed in
the classroom for the learners to read as the project progresses.
Site manager job description

Site managers are responsible for supervising construction sites and
running construction projects. They are also known as site agents,
contract managers, construction managers and building managers.
They are employed to prepare sites prior to the commencement
of construction work (to set out the site and organise facilities), to
plan projects and ensure that they meet agreed specifications, budgets
and/or timescales and to oversee building work. Other responsibilities
include:
• liaising with clients, professional staff (such as architects and
surveyors) and the public
• reporting progress
• supervising contracted staff
• meeting subcontractors
• making safety inspections and ensuring construction and site
safety
• checking and preparing site reports, designs and drawings
• maintaining quality control procedures
• motivating the workforce
• problem solving
• using specialist construction management computer applications.
Typical employers of site managers are:
• civil engineering companies
• building companies
• construction companies and contractors.
A small number also work for public sector organisations.
Qualifications and training required

Site managers need an appropriate qualification in construction/
building management, building engineering/studies, construction
engineering management or civil/structural engineering.
Relevant experience can be beneficial, although not essential.
Some employers offer sponsorship, vacation work and “gap year”
placements, which can provide valuable contacts and a useful insight
into the profession. Speculative applications made early in the
academic year are advisable, particularly to smaller employers.
Key skills for site managers include:

• good communication skills
• problem solving skills
• commercial awareness
• motivational skills
• team working skills.
Unit 1.2 MODULE 1 TERM 1 D11

Quantity surveyor job description
A quantity surveyor manages all costs relating to building and civil
engineering projects, from the initial calculations to the final figures.
Surveyors seek to minimise the costs of a project and enhance value
for money, while still achieving the required standards and quality.
Many of these are specified by statutory building regulations, which
the surveyor needs to understand and adhere to.
A quantity surveyor may work for either the client or the
contractor. They are involved in a project from the start, preparing
estimates and costs of the work. When the project is in progress,
quantity surveyors monitor expenditure.
The title of the job may also be referred to as a construction cost
consultant or commercial manager.
Typical tasks may include:

• preparing tender and contract documents, including bills of
quantities with the architect and/or the client
• undertaking cost analysis for repair and maintenance project work
• assisting in establishing a client’s requirements and undertaking
feasibility studies
• performing risk and value management and cost control
• advising on procurement strategy
• identifying, analysing and developing responses to commercial
risks
• preparing and analysing costings for tenders
• allocating work to subcontractors
• providing advice on contractual claims
• analysing outcomes and writing detailed progress reports
• valuing completed work and arranging payments
• maintaining awareness of the different building contracts in
current use
• understanding the implications of health and safety regulations.
Areas requiring more specialised knowledge include:
• offering advice on property taxation
• providing post-occupancy advice, facilities management services
and life cycle costing advice
• assisting clients in locating and accessing additional and
alternative sources of funds
• enabling clients to initiate construction projects
• advising on the maintenance costs of specific buildings.
Candidates also need to show evidence of the following:
• practical and logical qualities, and a methodical way of thinking
• a creative and innovative approach to problem-solving
• strong numeracy and financial management skills and the ability
to learn sophisticated design and costing IT packages
• the ability to write clear and precise reports and to relate complex
information simply to a diverse range of people
D12 SECTION D TEACHING GUIDELINES

• negotiating and team-working skills and the ability to motivate
and lead those on site
• detailed knowledge of past and current building and construction
technology, business and legal matters.
(http://targetjobs.co.uk/careers-advice/a-to-z-of-careers/site-manager)
Engineer job description

Engineers are problem solvers who use their expertise in science
and maths to do their job. They work in various branches of
engineering including aerospace, agricultural, biomedical, chemical,
civil, computer hardware, electrical and electronics, environmental,
industrial, materials, mechanical, mining and geological, nuclear and
petroleum.
Engineers who work in design and development:

• design, plan, and supervise the construction of buildings,
highways, and transit systems
• develop and implement improved ways to extract, process, and
use raw materials
• develop new materials that both improve the performance of
products and take advantage of advances in technology
• analyse the impact of the products they develop or the systems
they design on the environment and on people using them.
Engineers who work in testing, production, or maintenance:

• supervise production in factories
• determine the causes of breakdowns
• test manufactured products to maintain quality
• estimate the time and cost to complete projects.
Civil engineers design things. These might be roads, buildings,
airports, tunnels, dams, bridges or water supply and sewage systems.
They must consider many factors in their designs, from the costs to
making sure the structure will stay intact during bad weather. This is
one of the oldest types of engineering.
Many civil engineers manage people and projects. A civil engineer
may oversee a construction site or be a city engineer. Others may
work in design, construction, research and teaching. There are many
specialties within civil engineering, such as structural, construction,
environment and transportation. Civil engineers usually work in areas
where there is a lot of manufacturing and businesses.
Educational requirements for engineers

To get an entry-level engineering job, one usually needs a bachelor’s
degree in engineering. Sometimes a bachelor’s degree in Physical
Science or Mathematics may suffice, especially in high-demand
specialties. Generally, engineering learners specialise in a particular
branch of engineering.

A degree in engineering is needed for almost all beginning
engineering jobs. College graduates with a degree in a science or
Mathematics may get some jobs. A civil engineer must get a licence
from the State to offer services directly to the public. A licence
requires 4 years of relevant work experience and passing an exam.
Beginning engineers often work under an experienced engineer to
learn as much as possible. To teach engineering, further schooling is
needed.
Getting into engineering at tertiary level requires know-how of
Mathematics and science, and courses in English, Social Studies and
computers.
Engineers should be creative, curious, analytical and detail-
oriented. They should be able to work as part of a team. People skills
are important. This is because engineers often work with people in a
wide range of fields.
(http://targetjobs.co.uk/careers-advice/job-descriptions)
Architect job description

An architect designs buildings, houses and other structures. They
are commissioned by a group of people or individuals who want
well-designed structures. These structures are not built just for
aesthetic purposes but also for functionality. An architect might
also be commissioned to look over construction plans to make sure
every specification is met. This task is often done with the help of an
engineer who oversees the general construction of the design made by
architect.
The architect’s drawings have complete specifications, which
should be followed when the drawing is implemented. Aside from
working directly on paper, they could also transfer their work on
computers. An architect could also be seen working onsite where they
make sure their plans are properly implemented.
Training and education requirements

A degree in architecture is a must for those considering this career.
The degree usually requires five years of education and training where
learners are constantly exposed to different types of structures and
how they can be properly designed. After five years of training and
education, an aspiring architect has to pass the licensure exam. Success
in the industry often comes with experience, as people often prefer to
work with architects that have worked on some projects in the past.
An architect can work for the government, private companies and
individuals. Aside from designing structures for companies and private
individuals, an architect can also work as a teacher with universities or
technikons that offer architectural degrees.
Many architects work independently after setting up their own
construction company or architecture firm. They can also work as
freelance architects working for different institutions that would
require his or her services to design a structure.

Week 5
Learners will solve the problem and look at initial ideas. They will
evaluate and adopt a final idea.
Lesson 9 LB p. 36
Take a look at the various steps in bridge building. The steps are not
consecutive steps and are offered to give learners a better idea of how
bridges are built.
The photographs on pages 38 and 39 in the Learner’s Book are of
a bridge being built in Hermanus.
Take a brief look at an alternative to traditional bridge building
materials – recycled plastic.
Also, allow the learners to consider that building a bridge may not
be the only solution to the problem. Allow them to be creative about
their solutions.
ACTIVITY 16 Discussion LB p. 41
Group
Before designing the bridge, the learners need to consider the

information on pages 41 and 42 in the Learner’s Book. A scribe must
be appointed by the project manager to record briefly the main points
of the discussion and any issues that require further discussion or
research. These notes must also be kept in the file as they will form
part of the assessment of the project.
ACTIVITY 17 Sketch ideas LB p. 43

Group
Let each learner work individually to produce two possible ideas

to solve the problem. Once these sketches and ideas have been
submitted, the group, under the guidance of the project manager and
design engineer, must look critically at each proposal and decide on a
final idea. Each member must be ready to defend and explain his/her
idea. Encourage the groups to discuss the pros and cons of each idea
and provide help where necessary. Mediate if there is an impasse.
Lesson 10
ACTIVITY 18 Design skills LB p. 43
Group
Discuss as a class the concept of a design brief with specifications.

Make suggestions as you visit each group to ascertain how each
group is progressing.

ACTIVITY 19 Create a flow chart LB p. 43
Group
Each group must now discuss the order in which they will tackle the
project. They then record the order of work in the format of a flow
chart for each learner, highlighting his/her section of the work.
A flow chart must record the steps logically. Any two tasks done
simultaneously will appear in blocks alongside each other.
Week 6
During Week 6 learners will draw plans using first angle orthographic
projection with scale, line types and dimensions. They will also cost
out a budget for their project.
Lesson 11
ACTIVITY 20 Working drawings LB p. 43
Individual
Discuss very briefly the constraints when drawing a first angle

orthographic projection.
Making and costing skills

Read through the costing process, ensuring that the learners
understand how to cost the materials, the labour and the overhead
costs. Provide your learners with a Bill of Quantities so that each team
can cost their budget.
Explain that this is exactly what the companies who are tendering
for a particular job are required to do before submitting a tender.
The learners must then submit a detailed costing of their project.
Lesson 12
ACTIVITY 21 Costing the budget LB p. 45
Group
Let the learners draw up a budget for the project and keep it in their
project file. Assist groups who are struggling to do this activity.
Week 7
The learners will build their model to scale.
Lessons 13 and 14
ACTIVITY 22 Building skills LB p. 45
Group
The learners must work together building their models. Remind the
learners about:

• safe working practices
• the model must be neatly built
• it must be to scale
• it must show intelligent use of material.
Week 8
The learners will develop a rubric as a team to evaluate their own and
other teams’ work.
Lessons 15 and 16
ACTIVITY 23 Rubric creation LB p. 46
Group
The teams must now work together to produce a rubric, which they
will use to assess their own and the other groups’ models. Refer the
learners to the rubrics used in previous projects as a guide for their
thinking. Examples are available in the grades 7 and 8 Study & Master
Technology textbooks.
Week 9
Each group will present their tender bid to the Board.
Lessons 17 and 18
ACTIVITY 24 Communication skills LB p. 47
Group
Each team will present its tender bid to the ‘Tender Board’.
When assessing the team ensure that each member is responsible
for a certain aspect of the presentation.
Let the learners use the Level of effectiveness rubric to assess the
level of effectiveness of each group’s presentation.
Assessment
Project manager
Teacher/peer
Achievement level
Exceptional Organised, good delegation, good co-operation
with team
Achieved Organisation, delegation fairly effective, co-
operation not always evident
Minimum level Organisation, delegation sketchy, poor
leadership
Lacked achievement Ineffective as leader, poor organisation,
delegation

Finance manager and accountant
Teacher/peer
Achievement level
Exceptional Budget well laid out, neat, accurate
calculations
Achieved Calculations accurate, recording neat but did
not reflect good accounting practices
Minimum level Calculations inaccurate, poorly recorded
Lacked achievement Failed to keep records
Construction manager
Teacher/peer
Achievement level
Exceptional Organised building of model effectively,
workmanship excellent, built to scale, effective
use of materials
Achieved Led building well, workmanship good, built to
scale, fair use of material
Minimum level Led the building, workmanship poor, not
accurately scaled, waste of materials
Lacked achievement No responsibility for building, workmanship
poor, not accurately scaled, waste of materials
Design engineer
Teacher/peer
Achievement level
Exceptional Collated excellent sketched ideas of team,
plans used first angle projection with scale, line
types and dimensions, artistic representation
excellent
Achieved Collated sketched ideas of team, plans used
1st angle projection with scale, line types and
dimensions, artistic representation good
Minimum level Sketches average, plans lacked certain key
elements, artistic representation adequate
Lacked achievement Failed to take responsibility, sketches poor as
are plans with key elements missing, artistic
representation poor
Site manager
Teacher/peer
Achievement level
Exceptional Collected sufficient suitable materials, ensured
safe working practices, managed tools and
equipment well
Achieved Materials collected, safe working practices, fair
management of tools and equipment

Minimum level Adequate material collection, poor working
practices, tools and equipment not always
managed
Lacked achievement Poor material collection, poor working
practices, tools and equipment poorly
managed
Analyst
Teacher/peer
Achievement level
Exceptional Design brief excellent, rubric excellent, good
evidence of analysis of material usage
Achieved Design brief good, rubric good, evidence of
analysis of material usage
Minimum level Average design brief, average rubric, little
evidence of analysis of material usage
Lacked achievement Poor design brief, poor rubric, no analysis of
material usage
Team dynamics
Teacher/peer
Achievement level
7 All team members performed effectively, co-operated and
supported each other very effectively
6 All team members performed effectively, co-operated and
supported each other
5 All team members performed effectively, but argued often
4 Some team members performed well but took over others’
roles
3 Some team members performed well, but some members were
passengers
2 Some team members tried, but product poor
1 Little co-operation, product not completed in time
Week 10
Learners will do a formal assessment task of the work completed
during this term.

2
TERM
During this term you will revise pneumatics and hydraulics and do some practical
applications using syringes. The learners will do research on force transfer and
on Pascal’s principle. They will take a closer look at the hydraulic press and the
hydraulic jack. The learners will investigate pulleys and a variety of mechanical
control systems and revise the interactions of different gears. They will investigate a
situation so that an appropriate machine can be designed to solve the problem.
D20

Module
UnitMechanical
1 systems and control
2
Unit 2.1 Hydraulics and pneumatics
Week 1
Revise syringe mechanics, looking at pneumatic and hydraulic
systems. Let the learners experiment with different sizes of syringes
and experience force transfer. They will also research Pascal’s principle.

• equal sized syringes
• plastic tube or rubber tubing
• different sized syringes
• small plastic bath of water
• wooden stand
• a cup
• safety goggles.
Lesson 1 LB p. 52
Hydraulics and pneumatics

Learners learn about mechanical systems and control. They investigate
syringe mechanics using two equal sized syringes linked by a tube.
They identify the purpose of and difference between hydraulic and
pneumatic systems. They are introduced to the basics of pneumatic
and hydraulic systems, and apply the basic principles of these systems
into a construction project.
Read the notes in the Learner’s Book. Conduct a detailed
discussion with the learners on the purpose of and differences between
hydraulic and pneumatic systems. Use the experiments to facilitate the
discussion. Learners will discuss their answers in class.
Pneumatic systems
Pneumatic and hydraulic systems work in the same way, and are used
to provide powerful linear movement. The only difference is that
hydraulic systems use pressurised oil to operate, while pneumatic
systems use compressed air to operate. We are going to concentrate on
pneumatic systems. We will look at what they are, how they operate
and how they make our work easier.

Pneumatic systems use compressed air to make things work or move.
Compressed air is the normal air you breathe, forced into a small
space. Compressed air is used to pump up a bicycle tyre or to blow
up a balloon. When used correctly, compressed air is a safe form of
stored (potential) energy. Pneumatic systems consist of one or more
rams (piston and cylinder units) that are supplied with compressed air
through rigid or flexible tubes.
Pneumatic machines have many different uses. These systems
transmit force and movement over long and short distances with very
little friction. Pneumatic systems are used to control movement in
small appliances, such as dentist drills. They are used in tyre fitting
bays to undo and tighten wheel nuts, to remove old tyres from wheels
and to inflate tyres. Automatic doors of buses and trains, truck brakes
and construction drills are all examples of pneumatic systems. They
can also be used in models and prototypes to control movement over
a distance.
How pneumatic systems work

Pneumatic systems involve a source of compressed air that is
controlled by valves and causes output devices such as cylinders to
operate in a controlled way.
compressor
control valve pneumatic ram
Compressed air is produced by a compressor. An open pneumatic

system uses an air compressor and valves, which control the flow of air
to the pneumatic ram (the piston and cylinder unit). A double acting
ram can exert a pushing or pulling force, depending on which side of
the piston air is admitted.
A compressor is a pump driven by an electric motor or an internal
combustion engine that sucks air through filters and forces it into a
strong metal tank, called a receiver. The air moves along narrow plastic
or metal pipes to valves, which control the routing of the compressed
air. A range of actuators, including levers, rollers and solenoids, may
control the valves.
The air is then passed on to cylinders, which convert the energy in
the compressed air into linear motion. Finally, the used compressed air
is released into the atmosphere. During the process, the compressed
air may pass through filters and lubricators to clean the air and add

lubricants. It may also pass through regulators to control the amount
of pressure available in the system
Hydraulic systems
The extensive use of hydraulics to transmit power is due to the fact
that a properly constructed hydraulic system possesses a number of
favourable characteristics, such as:
• A hydraulic system eliminates the need for complicated systems
using gears, cams, and levers.
• Motion can be transmitted without the slack inherent in the use
of solid machine parts. The fluids used are not subject to breakage
as are mechanical parts.
Hydraulic system mechanisms are not subjected to great wear. If the

system is well-adapted to the work it is required to perform and if
not misused, it can provide smooth, flexible, uniform action without
vibration and is unaffected by variation of load. Hydraulic systems
can provide widely variable motions in both rotary and straight-
line transmission of power. The need for control by hand can be
minimised. In addition, they are economical to operate.
ACtiVitY 1 investigate a hydraulic and

pneumatic system using two equal
sized syringes LB p. 53
Group
Divide the class into two or more groups. Let them rotate so that all
groups complete all the experiments and record their findings.
Group A (pneumatics) set up the experiment using air. Group B
(hydraulics) set up the experiment using water.
Learners record results on the identification of the use of
hydraulics and pneumatics as mechanisms. Let them record what they
observe in their experiments in their workbooks.
Ask the learners the following questions: (See possible answers on
next page.)
1. What happens when you apply a force on the plunger of the main
cylinder? Explain your observation using the terms “hydraulic
system” and “pneumatic system”.
2. Does one system push back? If so, give an explanation for this
difference.
3. Which one moves more quickly?
4. Which one goes higher?
5. What causes the differences between water and air? Relate your
answer to particle theory.
6. How do these differences affect the work that air and water do?
Draw a comparative table on the board.
Unit 2.1 MODULE 2 tERM 2 D23

Possible answers
1. The second plunger will move upwards.
The hydraulic system will move a greater distance than the
pneumatic system because there is no compression in a hydraulic
system.
2. Yes – in the pneumatic system. In a pneumatic system the
compression of the gases causes a force on both sides of syringe A.
3. Hydraulic system
4. Hydraulic system
5. The particles in air are much further apart than the particles in
water.
6.
Gases Liquids
Are very compressible because Are not compressible, the particles

the gas particles are very spread in a liquid are not as spread out as
out in a gas
Pneumatics Hydraulics
Confined pressurised systems Confined pressurised systems that
that use moving air or gases use moving liquids
Because gases can be Liquids are not very compressible,
compressed, there is a delay in there is no delay in the movement
the movement
Need a compressor
Examples Examples
Precision drills used by dentists, Dump truck lift, hydraulic lift to
pneumatic brakes (air brakes) lift cars, jaws of life, blood in body,
used by trucks, buses and trains, used in cars
tampers used to pack down
dirt and gravel, lungs, nail gun,
dentist’s chair
Pressure and force

The terms force and pressure are used extensively in the study of fluid
power. It is essential that we distinguish between these terms. Force
means a total push or pull. It is push or pull exerted against the total
area of a particular surface and is expressed in grams.
Pressure means the amount of push or pull (force) applied to each
unit area of the surface and is expressed in Newtons per square metre
(N/m2). Pressure may be exerted in one direction, in several directions
or in all directions. Newtons (N) is the measure of force, therefore
pressure is is N/m2, otherwise known as pascals (Pa).

Pneumatic systems have two main features:
a) Pneumatic systems use compressed gas, such as air or nitrogen, to
perform work processes.
b) Pneumatic systems are open systems, exhausting the compressed
air to atmosphere after use.
Hydraulic systems too have two main features:

a) Hydraulic systems use liquids, such as oil and water, to perform
work processes.
b) Hydraulic systems are closed systems, recirculating the oil or water
after use.
Advantages of pneumatics
In pneumatics, a system needs only one power source. The work
process creates a lower noise level than hydraulic systems, and
pneumatic systems are relatively clean and operate at high speed. In
addition, pneumatic systems feature lower component costs.
If you have access to the Internet, show the learners the picture of
the small walking robot made using pneumatics at http://groups.csail.
mit.edu/lbr/boadicea.
ACtiVitY 2 Self-assessment LB p. 55
Individual
Let the learners complete the self-assessment. Note the areas in which
learners are struggling and address these with the specific learner.
1. A pneumatic system uses compressed air or gas to produce an
output. Refer to the explanation on page D21 for an explanation
of how pneumatic systems work.
2. Hydraulic systems use liquids, such as water or oil, to produce an
output. Refer to the note on page D23 for an explanation of how
hydraulic systems work.
3. Less effort is required to depress the pistons when the syringes are
filled with water compared to the syringes filled with air.
4. The hydraulic system works better.
5. a) The syringe filled with water works better. The water cannot
be compressed so the response of the pushing action is almost
immediate.
b) The learners are expected to apply the knowledge they have
and deduce what they think will happen. Let them explain
their answers. They will conduct an experiment to investigate
what really happens.

Lesson 2 LB p. 55
ACtiVitY 3 investigate a hydraulic and
pneumatic system using two
different sized syringe LB p. 55
Group
When you push down on the plunger (a force), you create a certain
amount of pressure inside the container (syringe). Tell the learners
that the amount of pressure inside the container (syringe) depends on
the amount of force applied to the plunger (how hard it is pushed)
and the surface area of the plunger.
1. The plunger in syringe B moves up.
2. The plunger in syringe A moves up.
3. The force applied to one syringe is transferred to the other syringe.
4. This will vary from group to group.
5. A small input force over a small area can produce a large force
over a large area.
6. If the area of a syringe is large, then the force required to push on
that syringe is large too. If the area of another syringe in the same
system is small, the force required to push on that syringe is small.
7. The large syringe. The large syringe is more difficult to press but
the small syringe’s plunger moves more.
Lesson 3 LB p. 56
Pascal’s principle
Ensure that the learners understand that, according to Pascal’s
principle, the pressure exerted by the fluid will be the same in all
parts of the container. In other words, any force applied to a fluid is
transmitted in all directions throughout the fluid, even if the fluid is
in two different containers (syringes) connected by tubing. Emphasise
that the shape and size of the second container will not affect the
pressure.
ACtiVitY 4 Construct a simple hydraulic system

LB p. 58
Pair
Learners conduct the experiment and observe what happens. Learners

will complete the answers to what they observed in this experiment.
When you push down on the plunger (a force), you create a
certain amount of pressure inside the container (syringe). Tell the
learners that the amount of pressure inside the container (syringe)
depends on the amount of force applied to the plunger (how hard it is
pushed) and the surface area of the plunger.
Does the syringe filled with air or the syringe filled with water
work best? The syringe filled with water works best, because liquids
are not compressible. If the two syringes are identical, then the force
D26 SECtiOn D TEACHING GUIDELINES

produced by the second plunger will be the same as that exerted on
the first plunger.
What do you think will happen when you use syringes of different
sizes? The bigger the syringe, the bigger the plunger surface area and
the more force it will produce. This is why, in the second part of the
demonstration using syringes of two different sizes, the smaller mass
was able to ‘lift’ the larger mass.
Learners learn about Pascal’s principle: pressure exerted on one
part of a hydraulic system will be transferred equally, without any loss,
in all directions to other parts of the system.
Learners will record their observations in their books and come to
their own conclusions regarding this experiment.
Discuss Pascal’s principle. Make use of an experiment to show
how this principle operates in theory. According to Pascal’s principle,
the pressure in one syringe is the same as the pressure in another
syringe in the same system.
Let the learners read and do research on Pascal’s principle and
indicate where some of these applications are found.
Possible answers
1. The same effort is required.
2. The large syringe has a large area, so the force required is large too.
3. When you press the large syringe in the system, it is more
difficult to press as you are moving a large amount of water, but
the small syringe’s plunger moves more.
4. A typical application of Pascal’s principle for gases and liquids is
the automobile lift seen in many service stations (the hydraulic
jack). Increased air pressure produced by an air compressor
is transmitted through the air to the surface of oil in an
underground reservoir. Hydraulics is employed by modern devices
ranging from very small to enormous. For example, there are
hydraulic pistons in almost all construction machines where heavy
loads are used.
5. Depressing the plunger in one syringe lifted the plunger in the
other syringe. The force was transferred directly from one syringe
to the other. Because the syringes were the same size
• both plungers moved the same distance, but in opposite
directions
• one plunger moved down and the other plunger moved up
• the force pushing down on one plunger was the same as the
force pushing up on the other plunger.
Remind learners that pressure is the ratio of force to area. This means
that if the area of one syringe is large, the force it takes to push on that
syringe must be large also. If the area of another syringe in the same
system is small, the force it takes to push down that syringe must be
small also.
When you push down on the plunger (a force), you create a
certain amount of pressure inside the container (syringe). Tell the

learners that the amount of pressure inside the container (syringe)
depends on the amount of force applied to the plunger (how hard it is
pushed) and the surface area of the plunger.
In this demonstration, the pressure will be the same in all parts
of the system – the first syringe, the plastic tubing and the second
syringe, regardless of its size (i.e. even if it is bigger than the first
syringe). Learners may not understand that the pressure will not
decrease in a larger syringe – they may believe that the pressure will
‘spread out’. Do not proceed with your explanation until learners
understand the uniformity of the pressure. A drawing may assist in
their understanding:
The pressure in the second syringe will create a force on the
second plunger, pushing it outward.
The amount of force produced by this second plunger will depend
on the pressure inside the syringe and the surface area of the plunger.
If the two syringes are identical, then the force produced by the
second plunger will be the same as that exerted on the first plunger.
At the same time, the bigger the syringe, the bigger the plunger
surface area and the more force it will produce. This is why the smaller
mass was able to ‘lift’ the larger mass in Activity 3.
Learners should clearly understand that using one small syringe
(as input) and one large syringe (as output) is a good way of increasing
force.
When you have finished your explanation, you can tell learners
that in mechanics, the use of fluid (water) power in this way is called
hydraulics.
Learners should have noticed that it took much less force to
push down on the small syringe and lift the load sitting on the large
syringe. When the same load sat on the small syringe, it took a lot of
force to push down on the large syringe and lift the load. Encourage
learners to share anything else they observed.
Note that as equal volumes of liquid are moved through the
systems, this results in different extensions (amount of movement)
where syringes (cylinders) are of different sizes:
Safety concerns
Remind learners that liquids used in the laboratory must not to be
consumed.
ACtiVitY 5 Hydraulics LB p. 59
Individual
Let the learners do research on any of the topics presented in the

Learner’s Book. Remind them to enhance their research notes by
including drawings.

Week 2
Arrange a field trip for the learners to view a hydraulic press in action.
Lesson 4 LB p. 59
Arrange an excursion to a place where a hydraulic press is used so that
learners may see a hydraulic press in use.
You may also demonstrate of the use of a hydraulic jack.
ACtiVitY 6 How a hydraulic jack works LB p. 62

Group
Describe how the hydraulic jack works. Fluid is pumped into the
piston and valves prevent its escape. This fluid generates pressure and
lifts the load piston.
The water flows in the direction of A to B. From the water
reservoir into the effort piston, then into the load piston and finally
back into the reservoir.
The purpose of the valves is to release the pressure that builds up
from time to time.
In nature, valves are used in the heart and blood vessels in animals
and humans, geysers and volcanoes.
Valve A Valve B
Effort piston moves down Open Closed
Effort piston moves up Closed Open
ACtiVitY 7 Self-assessment LB p. 63
Group
Let the learners make a simple mechanism that shows how a

pneumatic system works.
3. mechanical systems that are operated using air
4. mechanical systems that are operated using oils or liquids
5. garages to pump air, bicycle pumps, bus doors, train doors
6. car jacks, hydraulic jacks
For additional worksheets look at Siyavula http://cnx.org/content/

m31723/latest/ on the Internet.
Mechanical advantage – force multiplication LB p. 63

To calculate the mechanical advantage of a hydraulic system
An example of a simple hydraulic system is a hydraulic lift, which is
used to lift motor cars. The system has a mechanical advantage of both
power input and distance output.
The system consists of two pistons of different sizes, connected by
a reservoir that is filled with a hydraulic liquid such as oil or water.

force (smaller)
large piston
small piston B
distance
distance moved
moved
A
force (greater)
liquid that cannot
be compressed
The following formula can be used to calculate the mechanical

advantage:
load (output force)
Mechanical force advantage = ____________
effort (input force)
Mechanical advantage – distance output LB p. 64

In the syringes, the piston with the large diameter will have a smaller
distance output and the piston with the small diameter will have
a larger distance output. The relationship of distance output is
determined by the mechanical force advantage. For example:
The motor car in the example below weighs 5 000 N. The small
piston, A, has an area of 1 cm². The small piston moves a distance of
100 cm.
N
5 000 N
downwards
motion
A B
100 cm
upwards
motion
area x cm
1 cm2 area
100 cm2
1. Determine the input force. According to Pascal’s principle:

Pressure cylinder A = pressure cylinder B
force A = _____
_____ force B
area A area B
5 000
force A = ____
_____
1 100
Force A (the input force) = 50 N
2. The area at cylinder B is 100 times bigger. Therefore the power at
cylinder A is 100 times smaller.
Determine the mechanical force advantage.
5 000
load = ____
MA = ____ 50
= 100
effort

3. Determine the distance that the large piston will move.
MA = 100. Therefore, if the small piston moves 100 cm, the large
piston will move 1 cm.
Calculation 1 relating to Figure 2.15

1. Work = force × distance
= 10 N × 0,1 m
= 1 Nm = 1 joule
work
Distance =  ____
force
1J
=  
____
100 N
= 0, 01 m
= 1 cm
force
3. Pressure = ___
area
  10 N 2
= _____
10 cm
= 1 N/cm2
4. Force = pressure × area
= 1 N/cm2 × 100 cm2
= 100 N
Calculation 2 relating to Figure 2.16

= 100 N × 0,1 m
= 10 Nm = 10 joule
work
Distance =  ____
force
10 J
=   ____
25 N
= 0,4 m
= 40 cm
force
3. Pressure = ___
area
100 N
=  _____2
80 cm
= 1,25 N/cm2
4. Force = pressure × area
= 1,25 N/cm2 × 20 cm2
= 25 N
Give each learner a copy of Assessment: Module 2 (in Section E).
Module 2 assessment memorandum

1 a) Force = 2 N
b) MA =  _12
c) 1,5 cm
d) No, the small piston/plunger will move the furthest and
enable Jack to make the highest jump
2 a) The piston/plunger with a diameter of 1 cm
b) 1,5 cm

ACtiVitY 8 Working the hydraulic jack LB p. 66
Group
Bring a hydraulic jack to class. Demonstrate how it works by

operating it. Let the groups present their observations to the class.
Thereafter evaluate the design of the hydraulic jack in terms of
fitness for purpose. Let the learners copy and complete the table in
their workbooks.
Lesson 5 LB p. 67
Learners learn about drawing a systems diagram, which describes the
way a hydraulic system works.
A ‘systems’ diagram is essential when planning a project. It allows
you to show your idea(s) and whether or not they will answer the
design problem. It also allows you to think systematically and logically
about the design problem and how it can be solved. Above all, it keeps
you ‘on track’ and does not allow you to wander too far away from
the original design problem. A systems diagram is similar to a flow
chart, although on first sight it is much simpler and more precise. The
diagram is usually part of either the ideas or development sections.
However, do not restrict yourself to these two areas. If you feel it is
necessary, use this type of diagram wherever you like in the design
process.
Explain systems diagrams by drawing a simple systems diagram
that describes making a cup of tea, from filling an electric kettle to
pouring the tea into a cup. Remember, almost every process can be
divided into input, process and output. When learning about systems
diagrams and how they can be used it is a good idea to practice
drawing them by describing simple processes (like the example of
making a cup of tea).
Please note: Although the example system diagrams shown below
include electronics, system diagrams can be drawn for non-electronic
projects/products as well.
How to present a systems diagram

1. The systems diagram is divided into three areas - input, process
and output.
2. You should write about all the problems you are trying to solve in
the INPUT area of the page.
The writing under the input drawing should be precise and to
the point. There is no need for incredible detail. Include a limited
number of inputs, expressed as simple statements.
3. In the PROCESS area describe the type of electronics and/or
mechanisms that you intend to use in your project. Keep the
descriptions of circuits and mechanisms generalised. Explain how
the circuits/ mechanisms control the way your product will work.
The person using your product may also be part of the PROCESS.
4. Explain in the OUTPUT area what you think will be the overall
outcomes of your product.

ACtiVitY 9 Draw a systems diagram LB p. 67
Individual
Discuss how to draw a systems diagram. Talk about input, process and
output.
Let the learners draw a systems diagram, which describes the way
a hydraulic jack works. Concentrate on the input /process /output.
ACtiVitY 10 Hydraulic machinery LB p. 68

Individual
Let the learners examine several different pieces of hydraulic

machinery found on a construction site and record what they do and
how they work. Let them record their answers in their workbooks.
Here are some Internet resources that may be useful.
http://www.technologylearner.com/index.htm
http://www.bbc.co.uk/schools/gcsebitesize/design/
http://www.btInternet.com/%7Ehognosesam/gcse/
http://www.designandtech.com/
http://www.deyes.sefton.sch.uk/technology/
Unit 2.2 Pulleys
Week 3
The learners will do some practical investigations with regard to
pulleys and force multiplication. They will also investigate the
following mechanical control systems: ratchet and pawl, disc brake,
bicycle brake and cleat.
Lesson 6 LB p. 68
Learners learn about pulleys using action research: Practical
investigations.
Let the learners read the notes in the Learner’s Book. Let them
conduct experiments using pulleys to check how each of these pulley
systems work. Let the learners record their observations and come up
with conclusions to their findings.
Calculating mechanical advantage of pulleys

A pulley system consists of one or more combinations of wheels and
ropes, which can be fixed in place or movable. Pulleys help you lift
larger loads. To calculate the MA of a pulley, count the number of
ropes/cables supporting the load.

ACtiVitY 11 investigating pulleys LB p. 75
Group
What you need:

• a single wheel fixed pulley
• a single wheel moveable pulley
• a pulley block system (block & tackle)
• weights acting as loads
• rope.
Set up the various pulleys in your groups and investigate the working
principles in each type of pulley mechanism. Record your answers in
your workbooks and report to the class at the end of the lesson.
ASSESSMEnt tASK Understanding pulleys LB p. 75

Individual
Let the learners complete the assessment task on their own.
Assessment task memorandum

1. a) fixed
b) movable
c) block and tackle (6 marks)
2. a) The block and tackle system is a combination of several
pulleys. A common block and tackle system includes a rope
linking both fixed and movable pulleys (1 mark)
b) The number of efforts that help to lift the load is 4 (2 marks)
c) The mechanical advantage for this pulley system is: (2 marks)
load
MA = ____
effort
= 4T
__
T
=4
d) The load is 4 000 N. The effort needed to lift the motor car
engine is: (2 marks)
MA = load
____
effort
4 000
4 = ____
E
E = 1 000 N
e) The distance moved by the effort if this load is lifted 4 m is:
(2 marks)
distance moved by effort
4= _______________
4
Distance moved by effort = 4 × 4 = 16 m
[15 marks]
Lesson 7 LB p. 76
Learners learn about mechanical systems and control including ratchet
and pawl, disc brake, bicycle brake and the cleat.
Bring examples of each of these mechanical control systems to
class. Let the learners read the information in the Learner’s Book.

Conduct a discussion with the learners on the four mechanical control
systems pneumatic systems namely the ratchet and pawl, disc brake,
bicycle brake and the cleat.
Ratchet and pawl LB p. 76

Show the learners how the ratchet and pawl works. Let them identify
places where they’ve seen a ratchet and pawl in use.
Provide examples besides a winch and a ratchet screwdriver
Disc brakes/hydraulic brakes LB p. 78

Talk about the disc brakes. Let the learners identify the different parts
of the disc brake.
ACtiVitY 12 Bicycle brake LB p. 81

Group
What you need:

• A bicycle with brakes.
Ask the learners to bring bicycles with brakes to school. Let the
learners investigate how the brakes work. Let them record their
findings in their Technology workbooks.
Cleats LB p. 83
Let the learners look at some of the different types of cleats available.
Let them find out where cleats are used. They must each find at least
two examples.
ACtiVitY 13 Mechanical control systems LB p. 83

Pairs
Let the learners briefly explain how a ratchet and pawl, car disc brakes,
bicycle brakes and cleats work after they have investigated them in
class. Let them draw line drawings of them and record their findings
in their workbooks. They may present the information in the format
of a table. This is an example. Consider all correct answers presented
by the learners.
Mechanism name Type of Where it is used Mechanical How it is used

and drawing system advantage
Ratchet and pawl Mechanical A good example Can only be A ratchet is
gear system is a ratchet turned in a counter a mechanical
screwdriver. clockwise direction, device that allows
designed to continuous linear
prevent reverse or rotary motion in
rotation (single- only one direction
direction device) while preventing
motion in the
ratchet pawl opposite direction

Mechanism name Type of Where it is used Mechanical How it is used
and drawing system advantage
Disc brakes car Hydraulic To apply brakes on The pistons in the Pressing the brake
cars wheel cylinders pedal in the car,
exert a force on causes a small
the brake pads, piston in the
which rub against master cylinder to
the rotating disc, create a pressure
slowing down and in the brake
eventually stopping fluid, which is
the vehicle transmitted to the
wheel cylinders
Bicycle brake Lever and To apply brakes on Brake power is You pull the brake
linkage bicycles simply how hard lever with your
the brake clamps hand, the brakes
the rim, you must cable grabs the
adjust your pads lever, which pulls
closer to the rim the brakes to grab
for your brakes the rim as the pads
to have a higher squeeze the rim
mechanical
advantage
Cleat Mechanical Cleat (shoe), a type A rope or string is
or part of a shoe wound around the
or cleat (nautical) cleat to prevent it
a fitting on ships, from moving
boats and docks
to which ropes are
tied, also used to
secure cords and
flags to a pole
Week 4
This week learners will take a closer look at various kinds of gears.
Lesson 8 LB p. 84
Let the learners read the information in the Learner’s Book. Let them
revise the interactions of the following:
• spur gears of equal size counter-rotating
• spur gears of unequal size counter-rotating – note velocity/force
relationships
• spur gears using an idler to synchronise rotation.
ACtiVitY 14 Design a handout LB p. 86

Individual
Let the learners design a handout explaining each of the gears that
they have learned about in this section. Ask them to use a table form
and record their information in it. They must include line drawings
for each gear train used. Show them the format below to complete
their handout. Assess their completed table. Accept all correct answers.

Gears Diagram Uses Line drawing
Spur gears When spur gears of
of equal size equal size rotate,
counter- they move in opposite
P
rotating directions as the
meshing takes place.
Spur gears The diagram shows

of unequal a simple gear train
size counter- with A as the driver
rotating gear and B as the
A B
– note driven gear. When
velocity/ The drive gear A turns completely
is known as the The gear that is
force ‘input gear’ .
it only moves 15
being turned is
relationships referred to as the
teeth, therefore four
‘output gear’. revolutions of gear A
will move gear B once.
Therefore this acts
a a mechanism that
can slow down the
movement.
Spur gears driver To get two gears
using an to turn in the same
idler to direction, a third gear
synchronise has to be meshed
rotation follower between the two gears.
idler
This gear is called an
idler gear. An idler gear
changes the direction
of the movement of
the other gear and is
used to synchronise
rotation. The driver and
the driven gears can be
made to rotate in the
same direction.
Lesson 9 LB p. 87
Conduct a discussion about bevel gears of equal size – axis of rotation
90˚, bevel gears of unequal size – axis of rotation 90˚. Note velocity/
force relationships, rack-and-pinion gear systems as found on
automatic gates and steering racks and worm gear systems for large
reductions in speed and increases in force. Discuss their uses, and
what each does in a mechanical gear system.
ACtiVitY 15 Gears LB p. 89
Individual
Let the learners complete a table while they investigate the various
types of gears that they are learning about as mechanisms. Check
whether all the learners have completed the task, correct the task and
assist those learners who are struggling.

Gears Diagram Uses Line drawing
Bevel Bevel gears are used mostly A
gears in situations that require
of equal power to be transmitted at
size right angles (or applications
that are not parallel). B
O
Bevel Bevel gears are used to A
gears of change the direction of drive
unequal in a gear system by
size 90 degrees. The bevel gear
can also increase the speed B
of the rotation
Rack pinion
rotary motion
Rack and pinion gear
and systems involve the use of
pinion a round gear called a pinion
and a flat gear called a R
linear motion
rack gear rack. This system is used to A
change rotary movement Addendum
into linear movement and D line
the other way round. Pitch line
Root line
H
K L
P
F
C
Worm Worm gears are used to

and gear transmit power at 90° and
where high reductions
are required. The worm
resembles a thread that
rides in concaved or helical
teeth. Worm gears resemble
screws. A worm gear is
usually meshed with an
ordinary looking, disk-shaped
gear, which is called the gear
wheel or worm wheel.
Week 5
This week learners will examine various items using mechanisms and
they will create vanishing perspective drawings.
Lesson 10 LB p. 90
ACtiVitY 16 Evaluation and design skills
LB p. 90
Group
Conduct a discussion with the learners on the mechanisms found

in the kitchen/home/garage. Let them conduct the investigations

and evaluate each of the mechanisms according to set criteria. They
can include any mechanism they choose. The table below is only an
example.
HOME KITCHEN GARAGE WORKSHOP

Criteria bottle knives egg can hand vice grip wire ratchet
openers beater opener drill strip- spanners
pers
Who is it people people cooks/ cooks carpen- handy- electri- mechan-
for? chefs ters man cians ics
What is it open for to beat to open to drill to hold to strip to tighten
for? bottles cutting eggs cans holes equip- wires or loosen
caps ment nuts and
bolts
Will it do yes yes yes yes yes yes yes yes
the job
What metal/ steel metal/ metal metal metal metal metal
material pewter blades plastic
is it made
of?
Is the yes yes yes yes yes yes yes yes
material
suitable?
What cost cost cost cost cost cost cost cost
should it effective effective effective effective effective effective effective effective
cost?
Does yes yes yes yes yes yes yes yes
it look
good?
Is it safe yes no yes yes yes yes yes yes
and easy
to use?
Check whether all the learners have completed the task. Correct the
answers. Let the learners report on any three of these items, using the
criteria listed.
Lesson 11 LB p. 90
Read the notes in the Learner’s Book and do some demonstrations
on the board or in a technical drawing room. Let the learners look at
the examples of vanishing point perspective in the photographs. Let
the learners find photographs or drawings that use vanishing point
perspective and bring these to class to share.
ACtiVitY 17 Draw a 3D wooden object using single

VP perspective LB p. 91
Individual
Learners are expected to draw a 3D wooden object using single

vanishing point perspective. Teach this lesson to the class by doing a
demonstration lesson on the board, explaining in detail all the steps

related to single point perspective and the terminology associated
with this drawing. Learners are expected to enhance their drawings by
adding: texture of wood grain, colour and shadows to their respective
drawings.
ACtiVitY 18 Use single VP perspective to draw an

inside view of the classroom LB p. 93
Individual
Learners are required to draw the inside of their classroom. They

may follow the instructions in the Learner’s Book or here are some
alternative instructions for drawing a room. If you prefer these
instructions, there is no harm in using it. There is not one single way
of drawing a room.
Drawing a room in single point perspective

V. Ryan © 2002–2008 at http://www.technologystudent.com.
Look at the room shown below. Furniture has been placed inside it
and a colour scheme added. Follow the instructions below and on the
next page and draw the basic shape of a room – including furniture.
Once you have mastered drawing individual pieces of furniture in

single point perspective, you will be ready to design a simple room,
which includes basic furniture. The same techniques are used whether

drawing the skeleton of a room or the pieces of furniture inside it. Use
a single vanishing point and project guidelines back to it.
1.
Draw a rectangle and project the corners back to a vanishing point.

Remember, all lines should be faint at this stage.
2.
Draw a rectangle, which represents the back of the room. This must
line up with the guidelines projected back to the vanishing point from
the front rectangle.
X
3.
LINE ‘A’
Complete the basic room by rubbing out line ‘A’ and darkening the
outline of the entire room.
Learners will draw the inside of a classroom in single vanishing
point perspective.
FORMAL ASSESSMENT TASK: Mini-PAT 2

LB p. 94
Describe a scenario where a machine combining at least two of
the following sub-systems can be effective in giving a mechanical

advantage to make work easier: mechanical, electrical, pneumatic or
hydraulic systems. The mechanical elements may consist of one or
more of the following mechanisms: levers, linked levers, wheels, cams,
cranks, pulleys and/or gears.
Discuss with the learners what will be expected of them in the
practical making task. Learners will use all the knowledge that they
have gathered and will attempt to come up with solutions to their
design.
Let the learners read the notes in the Learner’s Book. Clarify any
points of confusion for the learners before they start the activity.
Week 6
Guide the learners to investigate a situation so that appropriate
machinery can be designed to solve the problem and create a design
brief.
Lesson 12 LB p. 95
ACtiVitY 19 investigation skills LB p. 95
Pair
Let the learners chat to their partners about ideas that could solve
the problem, need or want. They must investigate the situation so
that an appropriate machine can be designed to solve the problem,
need or want given in the scenario. They must investigate the possible
mechanisms and controls to be used together to make the machine.
The learners should not limit their thinking to conventional
solutions. Let each learner write his/her suggestions for the design
giving specifications and constraints.
The learners should write a design brief with specifications
and constraints for the problem. The design brief must be a short
statement of the problem to be solved and not a description of the
solution. An open brief allows for more creativity than a closed brief,
which describes a solution.
The design brief could be something like this:
When people work in a factory, they see a need for a simple
hoist to raise boxes of fabric from one floor to the next. Design a
safe, remote-controlled hoist, which could make use of a factory’s
compressed air supply.
A checklist for a design brief
Checklist criteria Yes no
1. It is a short, clear statement of what must be done.
2. It describes the problem and not a solution.
3. It describes who will use it.
4. It describes where it will be used.
5. It describes the benefit a solution will have.
6. It lists all of the constraints.

The factors that will limit design ideas are the constraints. These can
be stated as one word, for example, time, materials, tools, human
resources, cost. These must be considered prior to listing the product
specifications.
Lesson 13 LB p. 95
ACtiVitY 20 Design skills – sketches LB p. 95
Individual
Learners must draw two possible solutions to their designs. Sketches

can be in isometric or oblique drawings. Each learner produces two
sketches of viable possible designs. Thereafter, teams will meet and
examine the individual suggestions and decide on a final solution.
Remind learners that they will present their model to the class.
Conduct a discussion around presentations, research plans, flow
charts, models and budget constraints in relation to the practical
project.
Week 7
Learners will create working drawings using first angle orthographic
projection.
What you need:

• for the model – tools, cardboard, hydraulic and pneumatic
equipment, gears, pulleys
• for the presentation – chart paper, koki pens, data projector,
laptop
Lesson 14 LB p. 95
Let the learners practise the orthographic projection presented in the
Learner’s Book. Let them read the notes to remind themselves of the
different views.
ACtiVitY 21 Working drawings LB p. 97

Group
Demonstrate to the learners how to produce drawings for their

model/prototype using first angle orthographic projection. Each team
member draws a plan of the design or, if it is very complex, one or
more aspects of the design. Each learner must demonstrate her/his
competency in using this drawing technique.
The teams collaborate to produce drawings for their model/
prototype using first angle orthographic projection.
You may use the following rubric to assess the learners’ drawings:

Criteria 5 4 3 2 1 0
1. Accuracy of drawing
2. Makes use of scale
3. Makes use of all relevant
lines
4. Prints neatly and accurately
5. Dimensions the drawing
correctly
6. Demonstrates good
aesthetic design
Total
5 Outstanding achievement
4 Meritorious achievement
3 Substantial achievement
2 Moderate achievement
1 Elementary achievement
0 Not achieved
Lessons 15 and 16 LB p. 97
ACtiVitY 22 Make a prototype working model
LB p. 97
Group
Learners will make a model of their design. Remind learners to work
using safe working practices. The model must display a viable solution
to the problem. It should be to scale and neat, and show intelligent
use of available materials.
Week 8
The learners will present their solution.
Lesson 17 LB p. 97
ACtiVitY 23 Communication skills LB p. 97
Group
Learners must ensure that a full presentation is prepared and

presented to the class. Learners do presentations in a team.
Each team is given five minutes to present their solution in
the form of sketches, artistic impressions of the solution, working
drawings/plans, costing and their model. Give each learner a copy of
the self-assessment checklist – Graphic design as a design function (see
page E6).

3
TERM
During this term learners will find out more about electrical and electronic systems
and structures. They will also revise circuits and different forms of communication.
Learners will also build their own circuits.
D45
B1

Module
UnitElectrical
1 systems and control
3
You will need to spend two hours each week on Technology. The
lessons can be broken up into two one hour sessions or one two hour
session. The work has been broken up into hour lessons. If the learners
know a lot of the work and want to work ahead of the schedule, make
sure they have covered the basics. There are some extension exercises
that have been put in for the learners that work quickly and grasp the
different concepts quickly.
Each lesson is divided up into one hour sessions. Make sure all the
materials are available before starting your lessons.
Time is often a factor when trying to cover the different activities
in the classroom. When covering a number of these activities, it would
be easier to divide the learners into groups. Group. 1 can do Activity 1
and Group. 2 can do Activity 2, etc. Before the end of the lesson each
group will give a report back of their findings. This will assist you in
covering all the material required in each week.
Unit 3.1 Revision of component symbols
Week 1
In Week 1 the learners will learn about basic circuits, component
symbols and Ohm’s law.

• a variety of electronic components
• cells
• batteries
• lamps/bulbs
• lamp/bulb holders
• insulated wire
• a variety of switches
• buzzers
• voltmeters
• ammeters
• buzzers
• bells
• 9 V cells

• insulated wire
• wire for making the loop
• a wooden base
• two dowel rods (or anything else that is suitable)
• glue
• nails
• Christmas tree lights
• a variety of resistors.
Before each group starts their activity, make sure that they have the
components or materials needed. Remember, if you don’t have a lamp
holder, the lamp/bulb must be connected with wire on the side of
the metal base of the lamp/bulb and the other insulated wire must be
connected underneath or to the ‘nipple’ on the metal base.
Lesson 1 LB p. 100
ACTIvITy 1 Revision of component symbols
LB p. 100
Pair
Let the learners look at the different symbols and their uses on page
101 in the Learner’s Book. They can discuss the different components
with a partner.
Did you know? Two cells make a battery.

Discuss this with the learners. If you have one cell it is called and
‘cell’ but two cells joined together becomes a battery.
The learners will discuss the symbols they will use in this module.
See how many of these symbols they can identify. Read about what
the different components are used for. The learners must learn the
symbols that are required for the Grade 12 exams. They should learn
the symbols for the different components.
They can discuss the difference between cells that are connected in
series and cells that are connected in parallel. Once they know how to
connect these they will understand the symbols.
You could make a poster of these components and their functions
and keep it on the wall for the learners to refer to when they are
working on circuits and circuit drawings. Make sure that the learners
know the correct symbols for the electronic parts. The symbols are
always required when they are drawing a circuit diagram.
The symbols for lamps/bulbs connected in series and parallel are
different. The symbols look different and they also produce different
results. The learners will discover this later on in the module.
It is important that the learners learn to put together the different
connections. They might need to use them in their final design!
UNIT 3.1 TOPIC 3 TERM 3 D47

Switches connected in series and parallel also serve a different purpose.
The learners will have learned this in grades 7 and 8.
ACTIvITy 2 Homework LB p. 101

Individual
Encourage learners to speak to people in their home environment
about how some of the components may be used.
ACTIvITy 3 Cells connected in series and parallel

LB p. 102
Group
It is important that the learners know how to put together the

different connections and circuits.
Anything connected in series is normally one component
connected to the other component next to it or, in other words, in
a straight line. Remind the learners that when they connect the cells
in series they connect them back to back or positive to negative. Let
them read the + sign on the cell, etc.
A parallel connection is like parallel lines in Mathematics, the
components are connected alongside each other. This will make
it easier for the learners to remember the difference between the
different connections. Remember that these types of connections can
be used for a number of components, for example, cells, lamps/bulbs
and resistors.
When cells are connected in parallel, the cells lie side by side.
Label positive and negative on the cells and show how the wire has to
connect the two cells together. The learners will get together in groups
and discuss the different ways to connect cells.
Possible answers
Cells can be connected in a straight line or next to each other.
Parallel cells are not connected with the same wire and are connected
alongside each other.
Because there is a limited amount of time you may divide the class
into groups, with one group connecting cells in parallel and another
group connecting the cells in series. They can then demonstrate their
connections.
ACTIvITy 4 Lamps/bulbs connected in series and

in parallel LB p. 103
Group
Let the learners stay in the same groups and discuss the different
connections when using lamps/bulbs.

Possible answers
When lamps/bulbs are connected in series, if one does not work the
other will not work, but when you connect them in parallel they work
independently. This makes the parallel connection more effective.
The lamp/bulb in a parallel circuit also glows brighter and will still
continue to work if one wire is cut.
Lamps/bulbs in series
When the learners connect lamps/bulbs in series they are connectde to
the cells by the same wire. The current is shared by the lamps/bulbs.
ACTIvITy 5 Lamps/bulbs connected in series

LB p. 103
Individual
See if the learners can connect this simple circuit in series with a cell.
Note the brightness of the lamps/bulbs. What will happen if you add
more than two lamps/bulbs?
Possible answer
Normally the lamps/bulbs are dimmer if you add more to the circuit.
Sometimes one of the lamps/bulbs does not even light up.
Lamps/bulbs in parallel
When the learners connect lamps/bulbs in parallel, you can see that
the wires connected to the cells are separate, insulated wires. They
work independently from each other.
ACTIvITy 6 Extension LB p. 104

Individual
There are always learners that work faster than others. Allow them to
do the extension activity. See if they can connect the bulbs in parallel.
Note the brightness of the lamps/bulbs. If you add one more lamp
connected in parallel, what happens?
Possible answers
The lamps/bulbs stay just as bright if you add another bulb connected
in parallel.
The lamp that is still connected will continue to shine or light up
if you cut one of the wires connecting the lamps.
The headlights of a car are connected in parallel or separately. If
one lamp/bulb goes out or is broken then at least the other lamp will
work until you can change the lamp.

Faults in circuits
It is important to teach the learners how to find faults in circuits.
Often the learners blame the component when the circuit is not
working, but it is often a faulty connection or something was joined
incorrectly. Here is a fault finding check list. This can be made larger
or be made into a poster so the learners can see it when their circuits
are not working.
Fault finding in a circuit

Electrical circuits should never really break – you can fix them if you
know how! Here are some things to check when building a circuit:
1. Is the circuit made to the circuit diagram? If not, correct it to
match the diagram.
2. Are the joins firm? Check them. Make sure they have proper
contact. Make them secure.
3. Is there a short in the circuit? This means that the connecting
wires are touching. Try to fix it.
4. Is there a break in the wire? Replace the wire or fix the break.
5. Are the components connected in the correct order? Check and
change the way they are connected.
6. Are the components working? Check each component, for
example, the battery. Check each component with a meter or in
another circuit.
7. Are the values of the components correct? Check that the values of
the components match what is needed for the circuit.
8. Are the cells or battery connected the correct way? Reconnect
them correctly.
9. Is the cell or battery strong enough? Replace the cell or battery.
If the circuit is not working try the steps again.

It is important to teach the learners these steps as they often say
they cannot get their circuits to work when it is a simple fault. When
learners work in groups, they can help the learners who are not sure
how to connect the different components properly and they can learn
from each other.
ADDITIONAL HOMEWORK TASK Steady hand

game
This is an additional homework task, which you may give the learners
if there is enough time and you think your learners might enjoy it. Let
them make a ‘Steady Hand’ game using a circuit with a buzzer. This is
a lot of fun, and it will help the learners build a game using a simple
circuit. The ‘switch’ is the looped tool they use to play the game with.
If the loop touches the wire, the lamp or buzzer goes on.
What you need:
• a buzzer
• a 9-voltage cell
• insulated wire

• wire for making the loop
• a wooden base
• two dowel rods (or anything else that is suitable)
• glue
• nails.
Work in groups and build the circuit from the diagram below:
See if the learners can draw a circuit diagram for this game.
ACTIvITy 7 Switches LB p. 104

Individual
The learner will look at two different ways of connecting different

switches. Remember a switch is a control device.
The simplest type of switch is represented by the symbol shown in
Figure 3.6 on page 104 in the Learner’s Book. Two parts are shown: a
pole and a contact. It is called a single pole, single throw switch.
Remind the learners about the simple switches they learned about
in grades 7 and 8.
Switches connected in series (AND logic)

If a switch is pressed down we know that it is on or it is said to be at
logic state 1. An open switch or when the switch is off it is said to be
at logic state 0. In other words, when a logic gate produces an output,
the output is said to be at logic state 1, if there is no output means it
is at logic state 0.
If the learners understand this basic knowledge about “logic” they
will cope with the logic states and the Truth Tables. It is important
that they understand this before they go onto the next activities.
The circuit in Figure 3.7 on page 104 in the Learner’s Book is
called the AND gate. Switch A and Switch B are in the off position.
ACTIvITy 8 AND logic LB p. 105

Pair
Allow the learners to work with a partner but if you have a big class
then put learners into larger groups, they will look at the circuit

diagram in Figure 3.9 on page 105 in the Learner’s Book and work
out what will happen if one switch is pressed down.
Possible answers
If the learners press down one switch, the buzzer or lamp will not
work. The circuit is still open so the circuit will not be on or work.
What will you have to do to make the buzzer go off? Both
switches will have to be down for the buzzer or lamp to work.
A completed truth table:
TRUTH TABLE
INPUT OUTPUT
A B Z
0 0 0
0 1 0
1 0 0
1 1 1
Photocopy the assessment entitled ‘Components’ on page E29 to give

to learners at the end of Week 1.
Possible answers
Name Picture Symbol Use
Series battery This is an input device,
WERCELL
WERCELL
source of more energy

PO
PO
Parallel battery This is an input device,

PO
source of more energy

WERCELL
PO
WERCELL
Push switch Control device used to

temporarily close a circuit,
for example, a door bell
ON
SPST switch Control device that opens

or closes the circuit
Lamp/bulb Output device, lights up

when current heats up
Bell and buzzer Output device, vibrates

to give off sound when
current passes through it,
useful as an alarm

ACTIvITy 9 Switches connected in parallel
(OR logic) LB p. 105
Group
In this activity the learners will examine the OR switch and discuss it
in groups.
Possible answers
If switch A is down or on, it will make the lamp or buzzer go on.
If switch B is down or on, the circuit will work or be working.
When both switches are down the circuit will be on. The learners
will discover with the OR logic that switches are attached in a parallel
way. This means that any one of the switches can be used to make the
circuit work or they can both be on at the same time and the circuit
will work. This means that there is always a flow through the circuit
once the switch is pushed down.

Individual
Encourage the learners to do this task. They can put the circuit
together at home. Supply the learners with the materials for this
homework activity. You can use a lamp/bulb if you do not have a
buzzer. You may allocate marks for this homework task. When they
have completed the circuit and shown their peers, the components
can be taken apart and reused for other circuits.
Possible answers
Input Output
A B Z
0 0 0
0 1 1
1 0 1
1 1 1
Unit 3.2 Revision of simple circuits
In Grade 7 the learners will have learned about how a current has to
flow full circle, like the runner on a track. It is important to know
how the current flow as some components can only be connected in
a certain way. Even when the learners put cells together they have to
be connected in a particular way. Conventional current flows from
positive to negative.

ACTIvITy 11 Revision of simple circuits LB p. 106
Group
Divide the learners into groups. Give each group a different circuit to
put together. Make sure that each learner in the group has a job to do.
Each group will then demonstrate their circuit and give a report back.
Make sure that all the materials are ready before the lesson starts.
It is important that time is not wasted sorting out materials. It might
work better if the material for each group is placed in a cardboard box
or container. Each group will have what is needed for them to build
their circuit.
It is important that each group has the same voltage for the
different components so that the testing can be compared. The results
might not be consistent if the voltage is not the same.
Group 1: A simple circuit with the lamps/bulbs connected in series
Possible answers
The circuit does not work or is not in the ‘on’ position.
When the switch is making contact, the lamps/bulbs will light up.
Group. 2: A simple circuit with the cells connected in series and the
lamps/bulbs connected in series
Possible answers
If you cut the wire all the lamps/bulbs go out.
It will be interesting to listen to the discussion about the
Christmas tree lights. Make sure the learners have seen Christmas tree
lights. Set up a set of Christmas tree lights for the learners to observe
and then loosen one of the lamps/bulbs.
Possible answer
The Christmas lights are connected in series so if one lamp/bulb is
faulty they all go off. You have to test all of them to see which one
needs replacing.

Individual
If there is time and the groups are waiting for the other groups in the
class to finish their circuits, they can draw a circuit diagram for their
circuit.

Unit 3.3 Ohm’s law
Ohm’s law qualitatively: as voltage increases, current increases if

resistance is constant.
Teacher’s tip: Get learners to use an ammeter on their circuits before

they get to Lesson 2. Demonstrate how to use an ammeter.
Unit 3.4 Testing Ohm’s law
Lesson 2
ACTIvITy 13 Testing Ohm’s law LB p. 109

Group
The learners will be testing to see what happens when they increase
the voltage (electrical current) on a simple circuit.
Divide the learners into groups. Make sure each learner has a job
to do. They must get used to being fully involved because it is what
they have to do when doing the Mini-PAT. Each group will build the
circuit and then measure the voltage. The group will also demonstrate
to the class and give a report back at the end.
Connect the first circuit and note the brightness of the lamp/bulb.
Then add an extra cell and note the brightness of the lamp/bulb.
When you connected the second cell to the circuit, what happened?
When they have connected the third lamp/cell, what happens?
Ohm’s law LB p. 110

Explain Ohm’s law to the learners. Allow the learners to clarify any of
the information presented in class or in the Learner’s Book.
ACTIvITy 14 Plotting the graph LB p. 111

Individual
Give each learner a sheet of graph paper (see page E3). Let them paste
it in their workbooks and plot the graph to show the relationship
between potential difference and the current strength.
The graph should look something like the graph on the next page
when the learners have finished plotting it.

80
CURRENT (μA)
60
40
20
0 VOLTAGE (VOLTS)
ACTIvITy 15 Calculate values LB p. 112

Group
Show the learners how to use the formulae that relate to Ohm’s
law and then let them do the activity in their groups. Allow them
to compare their answers and explain to each other how they got a
particular answer if their answers are different.
Possible answers
1. V = I × R
V
R = __
I
= _62
=3
= 3 ohms
2. V = 0,4 × 25
= 10,0
Voltage is 10,0 V or 10 V
3. I = __V
R
= 12
__
4
=3
= 3 amps
V
4. R = __
I
12
= ___
0,1
= 1,2
Resistance = 1,2
V
5. I = __
R
12
= ___
100
= 0,12
= 0,12 amps

6. V = I × R
= 1000 × 0,01
= 10
= 10 V
Unit 3.5 Resistors
Week 2
In Week 2 you will cover resistor colour codes and calculating the
values of the resistors.

• a variety of resistors
• some small toys and items that use resistors.
Lesson 3 LB p. 113
Resistor colour codes

In this lesson the learners will look at resistors, which can be used to
control the flow of electricity. A resistor opposes the flow of electricity
but it also protects components.
Teacher’s tip: Resistors are not expensive but they are small so store
them in a well-marked box. A see-through plastic container will be the
best. The learners can then see what is in the container.
Distribute the resistors you have brought to class to learners. Let them
look at the resistor and recognise how the colour bands differ from
resistor to resistor.
Read through the information in the Learner’s Book and talk
about the purpose of resistors.
Let the learners practise drawing the resistor symbol in their
workbooks.
Low and high value resistors

Calculate the values of some sample resistors.

Individual
See if the learners are able to connect resistors in series and in parallel.
They should bring the circuit back to school to show the class. Give
them marks for the effort.

Lesson 4 LB p. 116
ACTIvITy 17 Estimate values LB p. 117
Group
Let the learners talk about how to calculate the resistance of a resistor.
Explain how the table can assist them to determine the resistance.
Let them look at the resistors on page 117 in the Learner’s Book and
estimate the resistance. Please note that these will not be accurate, as
the bands of the resistors in the pictures are not always clear enough.
ACTIvITy 18 Calculate resistance LB p. 117

Group
Give some resistors to the learners and ask them to calculate the
resistance values.
Self-assessment LB p. 118
Let the learners work through the self-assessment checklist. If
particular learners identify anything that they are still having difficulty
with, address the problem areas with them.
Unit 3.6 Components
Week 3
During this week the learners will cover switches, diodes, LED
transistors and sensors.

• a variety of electronic components
• NPN transistors
• resistors
• LDRs (light dependent resistors)
• thermistors
• touch or moisture detectors
• LEDs (light emitting diodes)
• polarised capacitors
• unpolarised capacitors
• voltmeters
• ammeters
• a variety of items using different switches
• push switches
• slide switches
• toggle switches
• rocker switches.

Lesson 5 LB p. 118
Enlarge the table showing the electronic components on pages 118
and 119 in the Learner’s Book and make it into a poster for the wall.
Remedial tip: Make the poster colourful, with big illustrations. The
dyslexic learner will remember the visual rather than the words. The
illustrations with the words in different colours or highlighted will
help the learners associate the picture with the word.
ACTIvITy 19 Switches LB p. 121

Class
Collect different types of switches for the learners to touch and use.
Often a scrap merchant, second hand shop or electrical shop will
sell different switches. It is important that the learners see how the
switches work.
ACTIvITy 20 Diodes and LED LB p. 122

Group
Remedial tip: Store the components in different boxes that are well
labelled with big printed words so that the learner can associate the
work with the actual component.
Let the learners examine the LEDs that you have brought to class.
Lesson 6 LB p. 122
Transistors
Let the learners copy the transistor and its circuit symbols into their
Technology workbooks.
ACTIvITy 21 Transistors LB p. 124

Group
Only NPN transistors will be used at this level. Connect a simple

transistor circuit.
Week 4
During this week the learners will cover simple electronic circuits with
different components. They will look at different sensor devices.

• Sensors
• LDRs
• thermistors

• motors
• solenoids (6 V)
• counters (6 V)
• relays
• capacitors
• soldering iron
• insulated wire
• batteries
• transistors.
Lesson 7
ACTIvITy 22 Sensors LB p. 125
Pair
Let the learners do this activity with a partner and then allow them to
give feedback to the class about their discussion.
LDRs are used in light sensing applications such as alarm devices,
street lights and camera light meters.
Lesson 8
ACTIvITy 23 Thermistors LB p. 126
Pair
Help the learners identify where one might use a thermistor.

Thermistors are used to limit current in devices that could
overheat, for example, they monitor the temperature of battery packs
while charging, and in toasters, coffee makers, refrigerators and hair
dryers.

Individual
Remind the learners to be careful when working with tools like

soldering irons. If they need assistance when building and testing the
circuit, they should ask a responsible adult at home to assist when
doing this homework.
Let the learners assemble the circuit and try it out. They can heat
up the thermistor by holding a soldering iron close to it or something
similar.
ACTIvITy 25 Touch or moisture detectors

LB p. 127
Pair
Let the learners share with the class why it is important to use a ‘bare’
wire for the sensor.

The wires must be bare so that the circuit may be closed.

Individual
Let the learners build the circuit and record their findings. Find time
in class to discuss the findings.
If there are learners whose circuits are not working, remind them
about common faults that might occur. One of the things to do is to
check that the voltage of the device and the battery match.

Individual
If there is time, let the learners build a touch moisture detector by

making a probe from an etched circuit probe. Let some of the learners
who build the touch moisture detector demonstrate their circuit to
the class.
ACTIvITy 28 Capacitors LB p. 128

Pair
Let the learners share their discussions with the rest of the class.
Capacitors are used in car audio systems, and very strong
capacitors are used in electric cars.
Self-assessment checklist LB p. 128

Ask the learners to write the answers to the questions in their
workbook. Make sure that all the learners understand the work to
date. Take time to teach the learners who are struggling in certain
areas.
Unit 3.7 Simple electronic circuits
Week 5
The learners will cover simple electric circuits.
What you will need in Week 5:

• LDRs
• LEDs
• thermistors
• transistors
• NPN transistors
• buzzers

• bells
• variable resistors
• 1 kohm resistors
• 6 V series batteries
• insulated wire
• lamps/bulbs
• lamp/bulb holders
• capacitors
• 470 ohm resistor
• 4,5 V series battery
• 3 V series battery
• DC power supply or photovoltaic panels
• 1000 µF capacitor switches
• wood
• circuit board
• cardboard
• glue
• pliers
• saw
• scissors
• pencils
• rulers
• erasers
• wire cutters.
Lesson 9 LB p. 129
ACTIvITy 29 Draw and assemble simple
electronic circuits LB p. 129
Group
Assign each group to the Group 1 or Group 2 activity.
Group 1
Make sure the learners check that they connected the LED the correct
way.
Group 2
Make sure the learners check that they connected the LDR the correct
way.
Once they have assembled the circuit, they must cover up the
circuit slowly with their hand and observe what happens.
Let them try using an LED, 470 ohm resistor, switch, and 4,5 V
series battery. They can then try building a circuit using an LDR,
buzzer and a 3 V series battery.

Formal Assessment Task: Mini-PAT 3 LB p. 131
Topic: Innovation – Electronic systems and control
Content: Design and make a working circuit
Scenario: These are the specifications you will help the learners
discuss.
Lesson 10
Scenario 1
Design a light for each end of a section of roadworks that can be
switched on at each end. The learners must use a circuit that they have
adapted from one they have already worked with.
Here are some criteria the learners may want to use:

• The structure must be neatly made and it must be stable.
• The circuit for the OR circuit must be hidden in the model
with only the switches showing. The circuit should be visible for
assessment and repairing.
Or
Scenario 2
Design and make a quiz game that will enable learners to study
Technology in a fun way. Here are some criteria the learners may use
for their project:
• It must have a strong structure to display the quiz game on.
• It must use an AND circuit.
• The learners may adjust the circuit diagram they have been given
slightly to be more creative and to suit the quiz game.
• The circuit should be hidden neatly underneath with only the
probes that will work the game showing.
• The circuit must have a light or a buzzer that goes off when the
answer is correct.
• It must have questions and answers that apply to Technology.
• It must have at least two different surfaces with questions.
• The game must be colourful and creatively decorated.
Or
Scenario 3
Design and make a device with two switches. If both switches are not
operated simultaneously, a buzzer or bell will go off. Here are some
criteria the learners may use for their project:
• It must use an AND circuit.
• The learners may adjust the circuit diagram they have been given
slightly to be more creative and to suit the box.
Remedial tip: Learners with reading and learning difficulties will

find the written part of the design process difficult. It is important
Unit 3.7 TOPIC 3 TERM 3 D63

that you help by placing these learners in suitable groups where they
will be helped. Allow these learners to write short sentences in their
workbooks. Do not mark them on their spelling but rather on the
work they produce. Encourage them to come to you for the spelling
of the more difficult words, or put some of the words onto a chart or
the chalk board. Make sure you use different colour chalk or colours
and also make the print large.
Week 6
The learners will cover appropriate circuits and start the design brief.

• All the materials the learners have been collecting to build their
final circuit.
Lesson 11 LB p. 134
ACTIvITy 30 Investigation LB p. 134
Group
Investigate the situation and the nature of the need so that an

appropriate circuit can be chosen to solve the problem, need or want
given in the scenario. A given circuit must be incorporated into the
design of a device that will use electronics to address the problem,
need or want.
Before the learners start their design let them think of the
following questions:
• What do they need for their design?
• What will it do?
• Who will use it?
• What will it be used for?
• Where will it be used?
• What features must it have to work properly?
• What materials can be used?
• What will it be made of?
• How will it work?
• What would it look like?
• How big should it be?
The learners must remember that this will also be part of their criteria
for assessing the end product.
Let the learners list the tools and materials they are going to use.

Lesson 12 LB p. 135
ACTIvITy 31 The design brief and sketches
LB p. 135
Individual
Before the learners start the design brief make sure they have rulers,
pencils and all the other stationery they need.
The design brief

Each learner writes his/her suggestion for the design with
specifications and constraints.
Each learner draws the circuit diagram.
Each learner produces a sketch in 3D showing the device that
will use the electronic circuit. Teams meet and examine the individual
suggestions to decide on a final solution. Make sure that the learners
are able to have a discussion. Walk around the classroom to help with
the discussions.
Tip: Go through the checklist with the learners. Some learners get
anxious and forget basic things.
Make sure they have the right equipment.

Ensure that the work is fairly divided up amongst the members of
their team. Remember that they will be assessed for their contribution
to the task as well as being assessed as a team.
They will be required to fill in an assessment of the other teams’
models and presentations.
Explain to the learners what DC stands for – direct current.

Let the learners work through the checklist. Address any problems
they may have.
Week 7
This week you will cover plans and the making of the device or model.

• Continue to collect all the materials to build the final circuit.
Lesson 13 LB p. 136
ACTIvITy 32 Design, sketch and produce LB p. 136
Group
The learners will produce plans for their device/model/prototype using

first angle orthographic projection. They will use all the knowledge
they have gained to draw the design. The plans should include a 3D

‘assembly’ drawing in exploded view showing how the model fits
together.
Each team member draws a working drawing of the design or an
aspect of the design.
The device/prototype/working model must showcase a viable
solution to the problem. It should be to scale and net, and show
intelligent use of available materials.
Lesson 14 LB p. 137
ACTIvITy 33 Produce LB p. 137
Group
Let the learners continue producing their model and drawings.
Week 8
The learners will present their projects this week.
What you will need for this week:

• Presentation material
Lessons 15 and 16
ACTIvITy 34 Communication – team presentations
LB p. 137
Group
Each team is given five minutes to present their solution in the form
of sketches, artistic impressions of the solution, working drawings/
plans, costing, and their model.
Photocopy this rubric (on page E6) for the learners to assess the
other groups and even do a self-assessment. They can also add more to
the rubric if they like. Each team will need the rubric filled in by the
other groups. See the levels of effectiveness table on page E7.

Let the learners complete the self-assessment. Assist the learners in
resolving any particular problems they may be experiencing.
Week 9
In Week 9 each learner will compile a record of their own individual
contribution to the task. They will record this in their workbooks.
This recording will be done over the two hour lesson for the week.

Lessons 17 and 18
ACTIvITy 35 Record of individual contribution
LB p. 138
Individual
Each learner compiles a record of his/her own individual contribution

to the task. It should be reflected in each learner’s workbook.

Let the learners complete the self-assessment. Remind them to be
truthful so that their assessment is a true reflection of the work they
have done.
Week 10
The learners will write an assessment. You may use the assessment (on
page E30) as we have created it or you may use this as a basis to create
your own assessment to suit your class.

4
TERM
During this term you will be focusing on the following concepts and skills:
the preserving of metals through painting, galvanising and electroplating, the
preservation of foods by storing, pickling and drying and/or salting. Learners will
investigate the different properties of plastics, their uses and ways to reduce, re-use
or recycle them. They will make a plastic product that will satisfy a need, want or
opportunity.
D68

Module
UnitProcessing
1
4
Unit 4.1 Preserving metals
Week 1
A week’s work will be covered in two one-hour lessons. At the end of
each week, the learners will do a self-assessment or peer assessment
task to revise the work you have covered in the two hours.
This week learners will learn about what metals are, their various
uses and ways to preserve metals by painting and galvanising. If you
have time, you can do an extension activity on platinum mining in
South Africa.

• vinegar
• salt
• copper wire
• large container
• battery
• sticky tape
• two pieces of metal – one copper and one nickel.
Ensure that you have all the materials and tools for the activities during
the week. Conduct the activities and experiments yourself beforehand
so that you are better prepared to assist learners who are struggling.
Lesson 1 LB p. 142
Read through and discuss the information on the preservation of
metals.
Activity 1 Preserving metals LB p. 147

Individual
Ask the learners to answer the questions in their Technology

workbook under the following heading: Preserving metals.
Possible answers
1. Metals are found in all rocks and soils and are elements that are
good conductors of heat and electricity.
UNit 4.1 MODULE 4 tERM 4 D69

2. In cars, trucks, buses, ships and aeroplanes. In aerospace (rockets
and the space shuttle), in computers and electronic devices that
require conductors (TV, radio, stereo, calculators, security devices,
etc.). For communications, food processing and preservation
(microwave and conventional ovens and refrigerators and
freezers), construction (nails in conventional lumber construction
and structural steel in buildings), biomedical applications (as
artificial replacement for joints and other prostheses), electrical
power production and distribution (boilers, turbines, generators,
transformers, power lines, nuclear reactors, oil wells and
pipelines), farming (tractors, combines, planters), household
appliances (ovens, dish and clothes washers, vacuum cleaners,
blenders, pumps, lawn mowers and trimmers, plumbing, water
heaters, heating/cooling appliances).
3. Corrosion of metals occurs when oxidation takes place, which
generally happens in the presence of water and oxygen. Rust is the
most common form of oxidation.
4. Open ended – any metal that that does not have a protected
coating on it will rust,
5. Open ended – repainting metals structures when rust occurs,
washing a car after you have been driving along the coast to wash
off salt that causes rust, electroplating, etc.
6. Electroplating and galvanising.
7. The condition of the metal structure, the type of metal, the
life expectancy of the metal and the environment in which the
structure is used.
8. An example of a simple flow diagram to show the galvanising
process.
Start
➡ Caustic cleaning
➧ ➧ ➧ ➧ ➧ ➧ ➧ ➧
Rinsing
Pickling
Rinsing
Flux solution
Drying
Zinc bath
Cooling
➡
Finish Inspection

Activity 2 Extension LB p. 148
Individual
South Africa is one of the largest producers of platinum and accounts

for almost 80% of the world’s platinum production.
1. Find out where the platinum mines are situated in South Africa
2. Find out what platinum is used for.
3. South Africa came under international spotlight because of the
Marikana Platinum Mine strike in August 2012. Find out more
about this strike and write a paragraph about it.
Guide learners who are struggling to find the information on where to

do research. Check that the learners have completed their tasks.
Lesson 2
Talk about the lesson expectations, ground rules, what electroplating
is, the process of electroplating, resources and equipment needed and
safety issues.
Activity 3 Electroplating LB p. 148

Group
Let the learners read through the instructions on how to conduct the
experiment. Let them work safely to electroplate a metal. Assist those
learners who are struggling.

Let the learners complete the self-assessment rubric regarding
electroplating.
Unit 4.2 Indigenous technology:

Preserving food
Week 2
The class will learn about indigenous technology that can be used to
preserve grain and how to preserve fruit or vegetables by pickling.

• a variety of preserved foods (to show)
• ingredients as listed in the recipe
• chopping board
• storage jars
• dish cloth
• knife
• apron, cap, gloves (optional)
• bin bag.

Lesson 3 LB p. 150
Activity 4 Preserving grain LB p. 151
Individual
Let the learners answer the questions in their Technology workbooks.
Possible answers
1. Grain kernels that come into contact with the damp clay begin
to ferment. This releases carbon dioxide gas (CO2) into the sealed
grain pit, which prevents bacteria and fungi from developing.
2. The pit is still filled with carbon dioxide gas, which is poisonous
to people. The pit needs to be left open for a few hours to allow
the carbon dioxide gas to be released so the child can breathe
when lowered into the pit.
3. It comes into contact with the damp clay.
4. A system diagram to represent the indigenous preservation system
used by the Nguni people.
System diagram showing the preservation of grain using grain pits

input ➧ Process ➧ Output
➧
➧
Fresh grain is Grain kernels that come Grain is
lowered into into contact with the preserved and
a hole dug in damp clay ferment kept fresh for
the middle of a and release carbon months.
cattle kraal and dioxide, which prevents
sealed with cow bacteria and fungi from
dung. developing.
Set aside the last ten minutes of the lesson for a discussion planning
session for Lesson 4, which is a practical lesson. Allocate the learners
to groups to plan resources needed for the next lesson. Give each
learner an assessment rubric to be used in Lesson 4 so that they can
plan according to criteria to be used.
Important reminder: Remind learners to bring resources and

equipment needed for Lesson 4 and to have a back-up plan for
learners who may forget.
Activity 5 Pickles from around the world

LB p. 152
Individual
Let the learners see if they can identify each of the different types of
pickles and state which country is famous for each. Let them write
their answers in their Technology workbooks under the heading:
Pickles from around the world.
D72 SEctiON D TEACHING GUIDELINES

Possible answers
A B c D E F
Mexico India China Japan Scandinavia Iran
Pickled Achar Picked Red Gari – Pickled Pickled Torsi
Jalapeno Chinese cabbage ginger Salmon
Activity 6 Homework LB p. 153

Individual
Let the learners list as many examples of how the types of food
illustrated on pages 155 and 156 may be preserved. A wide variety
of answers may be accepted and may include drying, salting, freezing
and canning.
Important reminder: Your next lesson will be a practical lesson. The

learners will work in groups to preserve food by drying or salting.
Remind them to bring all the resources needed for this lesson.
Lesson 4
Activity 7 Preserving food by drying/salting
LB p. 154
Group
Let the learners read through the instructions for the practical activity.
Let at least two people in the group check the list of requirements.
Talk about the ground rules when conducting the practical activity.
Share helpful hints and remind learners about hygiene and safety
issues when working with food. Give each learner a copy of the rubric
that will be used to assess this activity.
The drying/salting process takes time, allow time for the food to
be preserved using the method chosen and set a date for when this
will be assessed.
Assess the learners’ practical activity using the assessment rubric
for the preservation of food.

Group
Let the learners arrange a market day to sell the preserves they made
or arrange to donate the preserves to a needy organisation.
Suggestion: This can be assessed in Lesson 14 together with the

product made from plastic and the learner’s portfolio.

Unit 4.3 Processing plastic
Week 3
The focus this week is on the different types of plastic and their
uses. The learners will also learn how to identify and sort plastics for
recycling according to codes.

• a variety of products made from different types of plastic
• copy of the plastics table to complete.
Lesson 5 LB p. 155
Conduct a discussion about what plastics are and how to identify
plastics using SPI codes.
Activity 9 types of plastic LB p. 156

Individual
Give each learner a copy of the ‘Types of plastics’ table to complete.
Activity 10 investigating different types of

plastic LB p. 157
Individual
Give each learner a recording sheet to record the material that is being
recycled.
This is an awareness activity. Use this task to educate learners
about the importance of recycling Discuss why these plastics should
be recycled instead of landing in landfill sites. Recap the need to
recycle.
Lesson 6 LB p. 157
Learners learn about types of plastics and their uses and using SPI
codes to identify different types of plastic. Let them talk about the
properties of plastics, thermoplastics and thermosetting plastics,
recycling of plastic waste products and closed loop recycling.
Activity 11 Properties of plastic LB p. 159

Individual
Read the table and answer the questions follow. Write your answers
under the heading: Properties of plastic in your Technology
workbook.

Possible answers
1. Low density polythene (polyethylene)
2. Durable outdoors, more impact resistant
3. Expanded polystyrene – it is heat resistant
4. Nylon
5. Stiff, hard, tough at room temperature, light weight –any two
6. Splinters easily, scratches easily
7. Plasticised PVC
8. Polyester resin
9. Polyester resin – good resistance to heat, resistant to ultraviolet
light
10. Nylon

Sign the self-assessment checklist in the learners’ Technology
Workbooks.
Unit 4.4 Re-use of waste plastic
Week 4
This week the learners will learn about remanufacturing waste plastic
into pellets for re-use and draw a flow diagram.

• PETCO movie.
Lesson 7 LB p. 163
Let the learners read through the case study. Help to clarify anything
that is unclear to them.
Activity 12 Systems diagram LB p. 165

Individual
Read and discuss the case study in groups and draw a simplified
systems diagram showing the process involved in the manufacture of
recycled plastics. Label your systems diagram: Manufacturing waste
plastic into pellets for reuse.
Possible answers
See the next page for a systems diagram showing the manufacturing of
waste plastic into pellets for reuse.

input ➧ Process ➧ Output
➧
Collected Washed to remove New plastic
PET bottles residual pellets
placed in large
Cleaned using corrosive
cleaning baths
solution to remove
chemicals and glues
Plastic shreds placed in
large tumble dryers to
remove moisture
Or
recollected
INPUT
PET bottles
grinding, washing, conventional
➡
removal of caps and recycling
labels
PET flakes
280-290 ºC,
➡
PROCESS re-extrusion
vacuum degasing
amorphous
PET pellets
decontamination,
solid-state poly-
➡
180–230 ºC, >6 h
condensation
inert gas or vacuum
crystalline
OUTPUT
PET pellets
Check the learners’ systems diagrams while they work and correct
errors.
Lesson 8 LB p. 165
Learners learn about remanufacturing waste plastics into pellets for
reuse
Activity 13 case study 2: Moulding recycled

plastic pellets into products LB p. 165
Group
Let the learners read through the case study. Explain anything that is
unclear to them. Let them draw a systems diagram labeled: Moulding
recycled plastic pellets into products.

Activity 14 Questions about moulding recycled
plastic pellets into products
LB p. 167
Individual
Let the learners answer the questions in their Technology workbook.
Possible answers
1. Accept learners list of products and packaging made from PET
plastics
2. a) Community members: Provide a livelihood for community
members – encourages people to recycle, earn a living by
selling recycled plastics to recycling companies, people make a
living by recycling waste products from landfill sites
b) Packaging companies: lower cost of the manufacturing of
new packaging – helps in keeping with company policy of
being responsible for the end product of product that they
manufacture – ‘Cradle to Grave’ Policy
c) the Department of Environmental Affairs: Less money being
spent on clean-up operations, less waste for landfill sites
d) The environment: Less damage caused to the environment by
non-biodegradable materials
3. Blow moulding is when a melted polymer material is placed into
a mould and air is injected into the cavity, which pushes the
polymer into the desired shape. Compression moulding is when a
polymer is placed on the bottom half of a compression mould and
the top half is lowed onto the bottom half, pushing the polymer
into the desired shape.
4. Carpet companies use recycled resin to make polyester carpets.
Recycled plastic pellets are used in the textile industry to make
clothing, jackets and polar fleeces. Manufacturers of VCR and
audio cassettes use pellets from PET bottles to make clear sheets
or ribbon for VCR and audio-cassettes. Spunbond is used to
create geotextiles, which are used in roof insulation or as a means
of combating soil erosion. Engineering companies use engineering
plastics, pumps, gears and chemical-resistant components made
from recycled plastic pellets. Industrial manufacturers make
strapping tapes, magnetic tapes on smart cards, X-ray film,
cigarette filters and tennis ball felt from recycled plastic pellets.

Class
Contact PETCO and arrange to have a copy of their movie on

recycling sent to you to share with the learners.

Week 5
The learners will look at more case studies dealing with the use of
plastics in cars and in the home. They will also start planning for their
practical activity.
Lesson 9 LB p. 168
Formal Assessment task: Mini-PAt 4

case study 3: Plastics used in modern motor cars
LB p. 169
Let the learners read through the case study. Allow time for a class
discussion about the different ways in which plastic is used in the
production of cars. Encourage them to look at cars and to identify the
parts made of plastic.
Lesson 10 LB p. 172
Ask the learners to identify instances in which plastic is used in the
home. Let them read Case study 4: Lighting the way with plastic
bottles.

Individual
Let the learners watch the video on the Internet.
Activity 17 Using plastic LB p. 173

Individual
Let the learners read the case studies about plastics used in modern
motor cars and in the home and complete the table in their
Technology workbooks under the heading: The different uses of
plastic in motor cars and around the home. Provide your own reasons
where necessary.
1.
item Reason the item was manufactured from plastic
1 Plastic food wrap Airtight – keeps food fresh
2 Cordless phones More durable, will not shatter if dropped
3 Large appliances Resists corrosion
4 Rubber stoppers under chairs Plastic absorbs sound and will not scratch other surface
areas
5 Plastic on appliance plugs Plastic is an insulator and will not conduct electricity
6 Body parts of the Smart Car Light and easy to interchange panels, more scratch
resistant
7 The ZR Supercharged Reduces weight and allows you to see the engine
Corvette-Hood

item Reason the item was manufactured from plastic
8 Synthetic polyurethane Has the same look and feel as leather, aesthetically pleasing
leather door treatments and more affordable
9 Plastic hollow air bags Deploys more rapidly
10 Bumper fascia Less damage caused in the event of a collision, bumper is
light and can be easily removed and replaced
2. Let the learners write a paragraph on the use of plastic bottle

daylights being installed on roofs of informal shelters in South
Africa.
Check whether the tables have been completed. Help learners identify
reasons if there are gaps in the table.
Activity 18 Problem identification LB p. 174

Group
Use the knowledge that you have gained to identify a need or want that
can be satisfied by the making of a plastic item of your own design.
Let the learners discuss the questions in groups. Let the learners
complete the following written activity in their technology books:
Activity 19 Homework LB p. 175

Individual
Ask the learners to complete the tasks on sheets of exam paper and
file them in their Technology Portfolio under the heading: Task 1:
Identification of the problem that needs to be solved. This work needs
to be included in with their Technology Portfolio for an assessed mark
at the end of the year.
Important reminder! Bring your resources for your practice lesson
in Lesson 12.
Week 6
This week learners will practice their design skills by sketching using
isometric projections and first angle orthographic projections. They
will also practice the skills required for making their product.

• isometric grid paper
• resources and equipment as per design
• safety gloves
• multi-cutters
• bin bag
• pliers
• hammer
• a good adhesive glue to join plastic.

Lesson 11 LB p. 176
Activity 20 isometric projections LB p. 176
Individual
Give each of the learners an isometric grid to do draw their 3D

design. This activity must be included in the learner’s Technology
Portfolio for a mark at the end of the year.
Assess the drawings using an assessment rubric for isometric
drawings.
Activity 21 First angle orthographic projection

LB p. 178
Individual
Let the learners draw their design in first angle orthographic

projection. This activity must be included in the learner’s Technology
Portfolio for a mark at the end of the year.
Assess this drawing using the assessment rubric for first angle
orthographic drawing.
Important reminder! Remind the learners to bring their resources
for the practice lesson in Lesson 12 and the practical lesson in
Lesson 13.
Lesson 12 LB p. 179
Activity 22 Skills development LB p. 179
Group
Discuss the task. Make sure all members are aware of their
responsibilities. Let them practise measuring, marking, cutting,
bending and joining skills which will be needed in Lesson 13.
Important reminder:
Remind learners to bring the resources and equipment needed for
Lesson 13.
Week 7
During this week the learners will make their product. They must also
hand in their Technology Portfolio.
Let the learners use the checklist to ensure that their Technology
Portfolio is complete.

Lesson 13
Activity 23 Practical LB p. 180
Group
Learners work in groups to make a plastic product that will satisfy a

need or a want. Remind learners to work safely when making their
product. Remind them that this is an assessment task.

Individual
Arrange to donate your plastic item to a needy organisation.
Lesson 14 LB p. 182
Activity 25 Practical assessment LB p. 180
Group
Assess the learners when they present their completed product

together with their Technology Portfolio. You may allow learners to do
a presentation to the rest of the class if time permits.
Learners hand in their Technology Portfolio consisting of tasks
needed for assessment purposes.
Week 8
The summative year end examination.
All work covered will be examined. The understanding of the
knowledge the learners have gained and their application of this
knowledge will be examined. Identify any areas of concern and assist
learners to address these areas of concern.

Section E: P
hotocopiable
resources
This part of your Teacher’s File is for storing all photocopiable templates,
worksheets and resources that are provided and that you may come across in your
planning and research.
TOPIC TERM 3 E1
Technology_Grade 9_TG Photocopiable resources.indd 1 2013/07/02 5:25 PM

You may photocopy this page for use with Study & Master Technology Grade 9 E3
Learner’s Book.

Grid sheet
E48
E4 YOU MAY PHOTOCOPY THIS PAGE FOR USE WITH THE TECHNOLOGY GRADE 7 LEARNER’S BOOK. © CAMBRIDGE UNIVERSITY PRESS
You may photocopy this page for use with Study & Master Technology Grade 9
Learner’s Book.

Isometric grid sheet
YOU MAY PHOTOCOPY THIS PAGE FOR USE WITH THE TECHNOLOGY GRADE 7 LEARNER’S BOOK. © CAMBRIDGE UNIVERSITY PRESS E47
Learner’s Book.

Graphic communication as a design function
OUTCOME: The learner must be able to communicate design ideas.
Self-assessment
Complete the checklist to determine if the following requirements are present.
I have presented: Yes No
sketches of different design solutions to communicate my ideas
labelled sketches to clarify detail relating to the design brief and specifications/
constraints
developed the selected idea as a freehand sketch to show more detail
formal drawings e.g. orthographic first angle projection
formal drawings e.g. orthographic third angle projection
formal drawings e.g. isometric view
formal drawings e.g. oblique view
formal drawings e.g. exploded view
sequenced drawings, such as flow diagrams or flow charts, for the making process
dimensions and quantities of materials
Graphic communication as a demonstration of technical skills
OUTCOME: The learner must be able to apply appropriate formal drawing techniques when
designing:
Self-assessment
Complete the checklist.
The following aspects are present: Yes No
SABS convention for:
scale
line types
dimension lines
Enhancement of sketches
colour
texture
shade
thick lines
thin lines
shadow
Orthographic drawings (2D drawings)
first angle orthographic projection
third angle orthographic projection
correct axis
Isometric drawing (3D drawing)
correct axis is used
line quality is correct
Oblique drawing (3D drawing)
Perspective sketches (3D drawing)
Exploded views
Correct axis is used
Line quality is correct
Sequence drawings
Circuit diagram
Systems diagram
E6 You may photocopy this page for use with Study & Master Technology Grade 9
Learner’s Book.

Formal Assessment
Levels of effectiveness
Task 1: Answer sheet
Group: (Names of learners)

4 3 2 1 Comment
Investigates
Understands the problem context
Produced sequenced notes when making the model
Able to manufacture the model according to the design
brief
Communicates
Communicated ideas clearly in presentation
Explained their role clearly in presentation
Has developed a working drawing
Contributes
Contributed to the decision making and discussions in the
team
Used the portfolio to communicate technological process
Understands
Understands knowledge and concepts
Is able to use and apply research findings on different
circuits and components
Identifies the problem
Follows through on ideas that have been developed in a
logical way
Is able to solve the problem by applying the technological
process correctly
Designs
Has contributed towards the design proposed by the team
A variety of creative options were explored
Makes
Worked neatly and safely when using tools
Made a list of resources needed
Made of cheap or readily available materials
Circuit worked properly to suit the need
The model was strong enough
Able to bear in mind all the specification when making the
product
The model was well built, attractive
Evaluates
Able to evaluate their own model, drawing and
presentation
Able to evaluate peers’ models, drawings and
presentations
Planning
Stuck to constraints
Participated in preparing joint strategy for presentation
Learner’s Book.

4: highly effective 3: most areas are 2: some areas are 1: not effective
effective effective
Investigate There is evidence A good Some relevant ideas Ideas were not
of an excellent understanding of were considered appropriate
understanding of important ideas
important ideas
Communicate Product followed Good Incomplete Product differed
design brief and interpretation of interpretation of widely from
specification design brief and design brief and design brief and
specification specification specification
Ideas clearly and Good presentation Ideas were muddled Presentation was
accurately presented of ideas and presentation poor, ideas were
was average not clear
Excellent contribution Good contribution Little contribution No contribution
to discussions to discussions
Portfolio highly Portfolio Poorly documented Incomplete, little
organised and well organised and and incomplete effort, inaccurate
planned planned
Knowledge In depth knowledge Good knowledge Understands No understanding
of electrical and of electrical and circuits with
electronic circuits electronic circuits assistance
Problem Excellent follow Good follow Needs assistance Unable to follow
identity through on logical through on logical to follow through through ideas
ideas ideas ideas
Applies technological Good application Needs assistance Process
process correctly with application incorrectly applied
Design, Excellent visual Good visual Some visual appeal, Little visual
execution of appeal, bold lettering, appeal, fair size lettering poor, some appeal, poor
poster, etc. excellent use of lettering, good use use of colour and lettering, poor
colour, shading of colour, shading shading use of colour and
shading
Variety of creative Good creative Some creativity Little or no
options options creativity
Makes Used tools safely Mostly safe usage Some safety Ignored safety
aspects considered aspects
All resources and Most resources Some resourced Few resources and
tools listed and tools listed and tools listed tools listed
All specification Most specification Some specification Few specifications
followed followed followed followed
Good workmanship, Acceptable Errors in Product
attractive quality, quite workmanship incomplete,
attractive not good
workmanship
Evaluates Product and Good evaluation Either product or Product and
process evaluated, process evaluated process lack
recommendations or both done evaluation
made ineffectively
Peer product and Good peer One or both Both lack
process evaluated, evaluation ineffective evaluation
recommendations
made
Excellent strategy Good strategy Some good No strategy
planning planning ideas, but rather planning
haphazard
Learner’s Book.

Module1:Unit
Tenderapplicationforregistration
Msunduzi
Municipality
CITY OF CHOICE
PIETERMARITZBURG
M S U N D U Z I
SuppliersDatabaseRegistrationForm
Registration forms are to be delivered to:
The Msunduzi Municipality, Procurement Unit, 5th Floor, AS Chetty Building,
333 Church Street, Pietermaritzburg or Private Bag X205, Pietermaritzburg, 3200
Attention: The Procurement Manager
Enquiries
Telephone: 033-392 2486 or 392 2853
For office use

Supplier name ______________________________________________
Date application received ____________________________________
MSU Number MSU ___________________________________________
Supplier information captured by _____________________________
APPLICATIONFORREGISTRATIONONTHEMSUNDUZIMUNICIPALITY
SERVICEPROVIDERSDATABASE
1.0 BUSINESS PARTICULARS

1.1 Name of business as registered with the Registrar of Companies/Close
Corporations. ________________________________________
1.2 Name of business used for TRADING purposes. If different from 1.1 or name of
business if business is not registered with the Registrar.
_____________________________________________________
1.3 Registration number as registered with the Registrar of Companies/Close
Corporations (if applicable) ____________________________
1.4 Business physical address ____________________________
____________________________
____________________________
Postal code ______________
1.5 Business postal address ____________________________
____________________________
____________________________
Postal code ______________
1.6 Telephone no. ( ) ___________ Fax no. ( ) __________
Learner’s Book.

1.7 Cellular phone no. ____________________
1.8 Email address ________________________
1.9 Preferred method of communication (please tick): Email ❒ Fax ❒ Post ❒ SMS ❒
1.10 Company contact person/s (full name and surname)
1. ________________________
2. ________________________
1.11 VAT Registration No. (if applicable) ________________________
1.12 Unemployment Insurance Fund No. (if applicable) ________________________
1.13 Compensation Commissioner Registration No. (if applicable)
________________________
1.14 Income Tax Reference No. ________________________
NB: Insert Personal Income Tax Number if a one person business (sole trader)
and Personal Income Tax Numbers of all partners in the partnership.
Good day
Thank you for your response to register on the Msunduzi Municipality Database. The
application form of said database is attached for your attention.
Please complete the application form and return by hand the original form, together
with the signed Affidavit to the office of:
Msunduzi Municipality
Procurement Unit
5th Floor, AS Chetty Building
333 Church Street
Pietermaritzburg
3200
For the attention of Ms Thembile Zondi (Telephone 033-392 2486).
The following documents must accompany your application:

• Original copy of a Tax Clearance Certificate
• Copy of CK1 form for Close Corporation businesses
• Bank statement/An original cancelled cheque
• If it is a Pty Limited, CM documents must be attached.
Once this office has been received the above documentation, your application will be
added to the database.
Learner’s Book.

THEMSUNDUZIMUNICIPALITY
EXECUTIVE: SUPPLY CHAIN MANAGEMENT (ACTING)

MISS D NDLOVU
Tel No. 033-392 2472 Fax No. 033-392 2532
SUPPLIES AND SERVICES CONTRACT No. 30 OF 2011
COLLECTION, CONVEYANCE AND DELIVERY OF MONIES
Tenderer’s name: ________________________

Postal address: ________________________
________________________
________________________
________________________
Telephone no.: ________________________
Fax no.: ________________________
Email address: ________________________
Contact person: ________________________
Sealed tenders endorsed on the envelope “SUPPLIES AND SERVICES CONTRACT No.
30 OF 2011” must be placed in the Tender Box located in the Foyer, Ground Floor, City
Hall, 169 Langalibalele (Commercial) Street, Pietermaritzburg, 3201, not later than
12h00 on 1 July 2011 when they will be opened in public. Only tenders placed in the
tender box will be accepted and considered.
Learner’s Book.

BUSINESSOWNERSHIP
E12
List all the persons who are OWNERS in the Business/Trust, and indicate their involvement in the management/operation of the Business/Trust.
In cases of Handicapped Persons, proof of disability by a recognised related institution must be submitted for registration purposes. If insufficient
space, copies of this page may be made and added to this Form.
FullName IDNumber SACitizen Capacity: %Ownership/ Male/ Disabled HDI (*) %oftime
Before Member/Partner/Proprietor/ Partnership/ Female Race devoted
Technology_Grade 9_TG Photocopiable resources.indd 12

27/4/94 Shareholder/Trustee/ Trust/Interest W/B/I/C/ tothe
Beneficiary Yes/No Yes/No Other business
Learner’s Book.
(*) NB: The request for the Race of a person herein is required for STATISTICAL PURPOSES ONLY and is not intended to prejudice any Business in
any manner whatsoever.
LEGEND
(W) – White (B) – Black (I) – Indian (C) – Coloured
Nameoftenderer Total Istenderer Doestenderer Isprice Tendered Points Pointsfor Pointsfor Totalpoints
tendered responsive? havecapacity? realistic? priceof forprice HDI locality scored
priceEx. Yes/No Yes/No lowest tendered 5.00 5.00
VAT tenderer 90.00
You may photocopy this page for use with Study & Master Technology Grade 9
2013/07/02 5:25 PM
Module1
Letterofappointment
LETTEROFAPPOINTMENT
Date: ________
Dear Team
Contract Number: RSA 101-314-2012/1: THE DESIGN AND SCALE MODEL

CONSTRUCTION OF THE UMZINDUZI RIVER BRIDGE
It is my pleasure to advise you that the local municipality, in conjunction with the
municipality, has invited you to prepare a detailed bridge proposal and scale model for
the above-mentioned project.
The deadline for your bridge design is _____________ at _________ hours, after which
a penalty of _______ % per day will be incurred by your team. The contents of your
submission include the following:
• drawings of your design
• a budget/cost estimate for your design that includes the following costs
• excavation
• concrete
• reinforcement
• formwork
• labour
• skilled professional costs
• miscellaneous items as detailed
• a portfolio containing all the work, drawings calculations, assessments, rubrics,
sketches carried out in the reporting process The report should include any
additional information that will help us, the client, to understand the value of your
choices
• a model of your design built to scale
• a presentation made to the class and the client showing off your final design,
sketches, budgets and the role played by each member of the team.
The scoring of your final submission will be as follows:

• model
• presentation
• drawings, sketches
• design brief
• file.
We look forward to receiving your future submission, and to the successful completion
of this important community project.
Yours faithfully
Learner’s Book.

Module 1
The tender process

If a business decides that it wants to tender for a particular project, in other words the business
wants to submit a proposal to carry out a particular project, then it must put together a
business plan. Each business must be aware that there will be other businesses who will also
be submitting a proposal to do the same job. There is always lots of competition between
businesses for the projects that need to be done.
A business plan is very important as it outlines the goals that the business aims to achieve,
and it helps to establish the business’s credibility with suppliers, customers and investors.
Suppliers need to know that this business will be able to pay them for the goods or services
that they will be supplying. If the business needs to apply for credit (money), the plan will help
to reassure whoever supplies the credit that the risk is minimal. In other words, there is a good
chance that they will be repaid the money that they lend the business.
Advantages of a business plan

• Business owners who plan are more likely to survive.
• It gives you an overall view of the business and how different parts of it need to be co-
ordinated.
• It makes you evaluate what you intend to do and when you hope to do it.
• It gives you a document against which you can measure your progress.
• It can be used to show interested stockholders the idea behind the business.
• It can be used to help raise financing.
(Teacher Guide: Foundations of Business, Machado, pp 183–186)
In your group start writing down ideas for your business plan. These are some of the aspects
you need to think about:
• your company name, address and telephone numbers
• the names, addresses and telephone numbers of the owners and managers
• the names of the people who prepared the plan.
The business plan
• It is a summary of the total plan. It should only be written after the other information has
been collected. It highlights the major decisions.
• The business plan outlines the type of business, its objectives, its location and the market
it plans to serve. It must state whether it is a new or established business and if established,
give a history.
• The business plan explains what service is going to be provided and what gives it an
advantage over other competitors.
• The business plan must identify who your customers will be, how you identified your
customers and the benefits they will obtain. It should also state the number of competitors
you will face.
• The business plan explains who the managers are, their qualifications and skills.
If a business wants to tender for the municipality, then the first step is to collect a form from
the municipality, which they must then fill in, to be registered. The form must then be returned
to the municipality
Learner’s Book.

The business is now registered and is on the list of tenderers.
There are usually two kinds of tenders:

a) tenders putting forward ideas
b) tenders specifying the cost of specific projects.
When South Africa became a democracy, it brought about changes in the business
environment. Businesses are under pressure from politicians to empower members of previously
disadvantaged groups and communities by appointing more managers and staff from previously
disadvantaged groups in all parts of their businesses.
This has been done to compensate for the way in which most of the people were excluded
from many jobs as a result of the apartheid policies of the previous Nationalist government.
The situation has improved, but there is still an imbalance particularly in upper management
levels.
Because of the above issues, points are given to certain groups in the tender process. They
include the following:
• Women
They are given preference as they were marginalised in the past.
• HDI (Historically disadvantaged individuals)
This is a South African individual who could not vote due to the apartheid policy or is a
female and/or who has a disability.
• BEE
BEE is Black Economic Empowerment, which redresses the inequalities of the apartheid
era by giving previously disadvantaged groups (black Africans, coloureds, Indians and some
Chinese) of South African citizens economic opportunities previously not available to
them. Most companies now need to be BEE compliant.
• SMME
A SMME is a small, medium or micro enterprise. It is part of government policy to address
former disadvantaged groups.
A form is supplied that needs to accompany the tender. As you can see, points are given for
certain categories of owners, partners, members or shareholders.
Learner’s Book.

Module 1
Bill of Quantities
BILL OF QUANTITIES
Item Description Unit Quantity Rate Amount
100 Earthworks
101 Approach embankment m 12 500
102 Excavation m2 200
200 Falsework
201 Scaffolding m 500
300 Concrete
301 Abutments
301a Total height less than 4 m No 50 000
301b Total height greater than 4 m No 100 000
302 Columns m2 1 600

303 Pre-cast beams m 2
1 500
304 Bridge deck m2 2 000
305 Pylons m2 4 000
306 Arch-support m2 4 500
400 Steel
401 Truss bridge element m 3 000
500 Miscellaneous
501 Vehicle barriers m 2 500
502 Pedestrian sidewalk m 750
600 Construction site camp

601 Establishment Sum 20%
TOTAL
Learner’s Book.

Assessment: Module 1
1. Explain carefully what you understand by the term scale and why it is used in working
drawings. [3]
2. Fill in the missing information about different types of lines used in graphic
communication, in the following table. [7]
Description Drawn line General application

a) Visible outlines
Visible edges
b) Imaginary lines of
intersection
Dimension lines
Projection lines
Leader lines
Hatching
Outlines of revolved sections
in place
Short centre lines
Bending lines
Continuous thin, freehand Limits of partial or
interrupted views and
sections, if the limit is not a
ontinuous thin (straight
C chain thin.
with zigzags) Break line
Dashed thick
Hidden outlines
c)
Hidden edges
d) e)
hain thin, thick at ends

C f)
and changes of direction
Chain thick g)
3. What are the three views of a first angle orthographic projection? Explain from where
you view the object in each view. [6]
Learner’s Book.

4. Draw this cup hook on a scale of 1:2 and then 2:1. (4)
5. Copy the following drawings freehand. (10)
a) b)
c) d)
Learner’s Book.

6. Study the working drawing and answer the questions that follow. (9)
FRONT
036 WORKING DRAWING
VIEW
PARTS LIST
Nos.
Descriptions of Material Comments
1
1 Tube P.V.C. Painted
80
2 Disc Wood Glue to 3
3 Base Wood Varnished
012 × 20 DEEP
2 040 × 20 DEEP
25
176
13
45
19
13
38 25 25 38 25
TOP VIEW
ALL DIMENSIONS IN MM SCALE 2:3
a) Which parts are made of wood?

b) How deep are the 12 mm holes?
c) Which parts are made of PVC?
d) How many views are drawn?
e) How is part 2 joined to part 3?
f) What finish will be used on the wood?
g) How is the tube attached to the base?
h) How thick is the base?
i) Can the desk tidy be manufactured using only this working drawing?
Learner’s Book.

7. Name the types of lines used in this drawing. [7]
c
d
a
b 12
R29
e
1 f
8. Explain the forces at work in the diagram below. [6]
9. What is the difference between a static and a dynamic load? Give an example of each.
[4]
10. Look at the following pictures and decide what property of the material is being
illustrated. [4]
shattered glass
Junior hacksaw
Drill bit
a) b)
Learner’s Book.

poster putty being stretched
c) d)
11. List and explain three more properties of materials not mentioned in the previous
question. (6)
12. Explain why it is important to have knowledge of the property of a material before
using it in a building project. (3)
13. List five questions you need to ask yourself before deciding on a specific material,
such as wood, to use in a project. (5)
14. Look at the following pictures of different kinds of steel bridges. Put in the arrows to
show the forces at work in each bridge when it is loaded. Name the different forces.
(15)
a) b)
c) d)
15. Why must an iron bridge be repainted often? (2)

16. What is a tender and why is it necessary? (2)
17. What are the advantages of having a business plan? (5)
18. Explain the following terms
a) BEE
b) HDI
c) SMME (3)
19. What two kinds of tenders are there? (2)
20. Match up the job with the job description.
JOB JOB DESCRIPTION

1 Site manager A will, with the help of the team, devise a solution for
the problem and oversee the working drawings for the
design and the artistic drawing
2 Analyst B oversees the actual construction of the structure, i.e.
the model
3 Acountants C analyses existing products/structures with regard to
their suitability
Learner’s Book.

JOB JOB DESCRIPTION
4 Design engineer D who will price the cost of the materials, transport and
the labour required
5 Finance manager E is responsible for the collection of all the relevant
materials to be used in the construction work
6 Construction manager F will oversee the budget and the calculations of the
costing of the project
(6)
21. What are the three major costs when working out a budget? (3)
22. Look at the following drawing and find five things that show poor safety practices in
the Technology classroom. (5)
b)
a)
d)
c)
e)
Learner’s Book.

23. By making use of the length, width and height dimensions, indicate which of the
following orthographic views correspond with the models below. [6]
a) b) c)
d) e) f)
A B C
D E F
Learner’s Book.

Assessment memorandum: Module 1
1. Scale is a ratio used to indicate the relationship between the drawing of the object and its
real size. [3]
2. [7]
Description Drawn line General application
Continuous thick Visible outlines
Visible edges
Continuous thin (straight or Imaginary lines of intersection

curved) Dimension lines
Projection lines
Leader lines
Hatching
Outlines of revolved sections
in place
Short centre lines
Bending lines
Continuous thin, freehand Limits of partial or interrupted
views and sections, if the limit
is not a chain thin line
Continuous thin (straight Break line

with zigzags)
Dashed thick Hidden outlines

Hidden edges
Dashed thin Hidden outlines

Hidden edges
Chain thin Centre lines

Lines of symmetry
Trajectories
Chain thin, thick at ends and Cutting planes
changes of direction
Chain thick Indication of lines or surfaces

to which a special requirement
applies
3. Front view, drawn by looking directly at the front of the shape

Side view, drawn from looking at the side of the shape
Plan view, drawn by looking directly down on the shape from above [6]
4. Drawing of cup hook [4]
5. Assess freehand drawings. [10]
6. a) Parts 2 and 3
b) 20 mm
c) Part 1
d) 2
e) With glue that is able to affix PVC to wood
Learner’s Book.

f ) varnish
g) with glue that affixes wood to wood
h) 25 mm
i) Yes [9]
7. a) construction line
b) sectioning line/cross hatching
c) section line
d) centre line
e) dimension line
f ) hidden detail
g) visible outline [6]
8. compression
tension
tension
compression
9. The difference between static and dynamic loads is that a static load does not change and is
either the structure’s own weight or is the load being carried by the structure, for example,
a person standing holding a bag of groceries. Whilst a dynamic load is one that changes, for
example, traffic crossing a bridge. [4]
10. Properties of material:
a) hardness
b) brittle
c) ductile
d) malleability [4]
11. Other properties: [6]
• tensile – how good the material is at withstanding a pulling force or tension force
• compressive – how good a material is at withstanding a compressive or squeezing force
• strength – refers to the force needed to break something and must not be confused with
stiffness, which is a measure of how flexible something is. For example, steel is stiff and
strong but although a biscuit is stiff it is not very strong
• malleability – ability to be hammered or rolled without breaking
• conductivity – ability to allow heat and/or electricity to pass through it
• toughness – ability to withstand knocks without being damaged or fractured
• durability – ability to withstand corrosion, wear and tear, weather conditions, etc.
• stability – ability to resist changes in shape and size
• weight/mass and density – some materials are light while others are heavy. Density is
how densely (closely) the atoms are packed together in a material, making it easy or
difficult to break
• corrosion resistance – ability of the material to resist the process of rusting.
12. You have to know whether the material can perform the task required and not distort or
bend under forces, rust or break. [3]
Learner’s Book.

13. Is the material readily available? How much will it cost? Is it affordable? Is the material
biodegradable? Will the use of the material have a negative impact on the environment? Is
the material poisonous? [5]
14. Arrows showing forces [15]
Bridge Forces at work
a) beam bridge When loaded, the beam or girder bends
downwards, producing tension in the
lower part of the beam and compression
in the upper part
b) Cantilever When loaded, the beam bends, producing

bridge compression in the lower part of the
beam and tension in the upper part
c) Arch bridge The bending effect on the beam and

the tension effects are reduced by the
compression forces provided by the
abutments
d) Suspension Nearly all the stresses are caused

bridge by tension. The pillars are under
compression
15. An iron bridge needs to be repainted as it begins to rust when exposed to the elements. [2]
16. It is a proposal to carry out a particular project. It is necessary to ensure that costs are kept
down and that the best possible contractor is chosen, who is competent enough to carry
out the work. [2]
17. Business owners who plan are more likely to survive. It gives you an overall view of the
business and how different parts of it need to be co-ordinated It makes you evaluate what
you intend to do and when you hope to do it. It gives you a document against which you
can measure your progress. It can be used to show interested stockholders the idea behind
the business. It can be used to help raise financing. [5]
18. a) BEE is Black Economic Empowerment, which redresses the inequalities of the
apartheid era by giving previously disadvantaged South African citizens (black Africans,
coloureds, Indians and some Chinese) economic opportunities previously not available
to them. Most companies now need to be BEE compliant.
b) A HDI is a historically disadvantaged individual who because of apartheid could not
vote, or is a woman, or has a disability.
c) A SMME is a small, medium or micro enterprise. [3]
Learner’s Book.

19. Two kinds of tenders: tenders putting forward ideas and tenders specifying costs of a
project.[2]
20. 1E The site manager is responsible for the collection of all the relevant materials to be
used in the construction work.
2C The analyst analyses existing products/structures with regard to their suitability.
3D The accountants will price the cost of the materials, transport and the labour
required.
4A The design engineer will, with the help of the team, devise a solution for the problem
and oversee the working drawings for the design and the artistic drawing.
5F The finance manager will oversee the budget and the calculations of the costing of
the project.
6B The construction manager oversees the actual construction of the structure, i.e. the
model.
[6]
21. Cost of shuttering, cost of labour, overhead costs [3]
22. Identify unsafe behaviour in picture such as:
a) long hair loose
b) standing on unstable chair
d) the tie is not tucked away in the shirt
e) the wires are exposed [5]
23. a) B [6]
b) C
c) E
d) F
e) D
f) A
Learner’s Book.

A little boy receives a Jack-in-the-box toy from his grandmother (see illustration).
Jack-in-the-box mass 100 g
cylinder B
area of piston is 1 cm2
cylinder A
area of piston is 2 cm2
spring
1 a) Calculate the amount of force, in newtons, that the little boy needs to make the
Jack-in-the-box weighing 100 g shoot out, when the area at cylinder A is 2 cm2
and the area at cylinder B is 1 cm2.
b) Calculate the mechanical advantage in question 1.
c) Calculate the distance that piston A must move to make the Jack-in-the-box shoot
out 3 cm.
d) Would it be more advantageous to change around the two pistons, A and B?
2. You have to make a pair of hydraulic pliers, as indicated in the sketch. To enable you
to do this, you are given two cylinders with pistons of 2 cm and 1 cm respectively. The
maximum distance that the larger piston can move in the cylinder is 3 cm. A force
of 1 N is applied to move the moving jaws of the pliers over a distance of 3 cm and to
clamp the jaws of the pliers.
can move back and forth over the beam
A B
N 3 cm
jaw that has to move across jaw in fixed position

3 cm in order to clamp
a) Which of the two pistons are you going to place in position A for a minimum force
input? Explain your answer.
b) How far will the piston at cylinder A move to clamp the jaws?
Learner’s Book.

Formal Assessment
Assessment:Task
Components
1: Answer sheet
Draw in the circuit symbol and give a short sentence of how the component is used.
Name Picture Symbol Use

Series battery
WERCELL
WERCELL
PO
PO
Parallel battery
PO
WERCELL
PO
WERCELL
Push switch
ON
SPST switch
Lamp/bulb
Bell and buzzer
Learner’s Book.

Formal Assessment
Assessment:
Task
Module
1: Answer
3 sheet
Name: ____________________ Date: ___________________
1. Draw the symbols for the following components:
Component Function Draw the circuit symbol

Supplies electrical energy
More than one cell, supplies

electrical energy
Allows the current to flow

through the circuit
Converts electrical energy to

light energy
Output device that gives off

light
Converts electrical energy

into sound energy
Controls the flow of current

in a circuit; the current flows
only when the switch is
pushed
into sound energy
Learner’s Book.

2. Draw the circuit diagrams of the following circuits:
Circuit Circuit diagram
3. Name these types of switches and draw the symbol:

v
Switch Name Symbol
Learner’s Book.

Switch Name Symbol
4. What happens to the voltage when lamps/bulbs are connected in series?

a. They become brighter
b. The voltage is shared
c. They don’t work
5. What are switches used for in a circuit?
a. To move up and down
b. To turn the circuit off and on
c. To give the components power
d. To work as an insulator
6. How do you connect an LED (light emitting diode) to a circuit?
a. You connect the one leg only to the circuit
b. You connect the negative leg to the positive path
c. You connect both the legs of the LED to one insulated wire
d. You don’t connect the legs of the LED to any insulated wire
7. What is the unit of measure for the flow of electricity?
a. It Is measured in meters
b. It is measured in amps
c. It is measured in ohms
d. It is measured in kilograms
8. What is the unit of measure for resistance?
a. amps
b. ohms
c. meters
d. kilograms
9. What two things does a resistor do in a circuit?
a. It controls light and changes the direction of the power
b. It controls the flow of electricity and protects the components
c. It controls the buzzer and the bell
d. It controls the ohms and amps
10. What does a LDR depend on to work?
a. It depends on the amount of moisture
b. It depends on the amount of ohms
c. It depends on amount of light falling on it
d. It depends on the amount of touch
11. Where would you use a thermistor?
a. You would use it to make coffee
b. You would use it to make light
c. You would use it in a fire alarm
d. You would use it as a timer
Learner’s Book.

12. In the language of logic, when a switch is closed it is said to be …
a. at logic state 0.
b. at logic state 2.
c. at logic state 1.
d. at logic state 0 and 1.
13. For the component to work for an OR gate …
a. one switch must be closed.
b. both switches must be closed.
c. none of the switches must be closed.
d. None of the above
14. For the component to work for an AND gate …
a. one switch must be closed.
b. both switches must be closed.
c. none of the switches must be closed.
d. None of the above
15. SPDT switch stands for …
a. super pole, double throw.
b. single pole, down throw.
c. single pole, double throw.
d. double pole, single throw.
16. DPST switch stands for …
a. super pole, double throw.
b. double pole, down throw.
c. single pole, double throw.
d. double pole, single throw.
17. Name the switch and draw the symbols below:
Name the switch Illustration of switch Draw the symbol
Learner’s Book.

18. What do the following circuits represent in electricity?
Symbol Drawing Symbol name
19. Can you identify the symbols for the following logic states? Fill in the output in the
truth table next to each symbol.
TRUTH TABLE
a) A
Input Output
Z
A B Z
B
0 0
.gate 0 1
1 0
1 1
0 0

0 1
1 0
1 1
b) A
.gate
Learner’s Book.

20. Complete the table below. Fill in the missing values of the resistors
How to determine the resistance of a resistor
colour 1 2 Zeros
Black
Brown
Red
Orange
Yellow
Green
Blue
Violet
Grey
White
21. Complete the following sentences:

a. The first two bands on the resistor represent the first ________ digits in the
number.
b. The third band represents the ‘_________’. (This is the number of zeros to be
added at the end.)
22. Draw a circuit to show an OR gate.
23. Draw a circuit to show an AND gate.
Learner’s Book.

Module 3: Assessment memorandum
1. Component Function Drawthecircuitsymbol

Supplies electrical energy
More than one cell,

supplies electrical energy
Allows the current to flow

through the circuit

to light energy
Output device that gives

off light

into sound energy
Controls the flow of

current in a circuit; the
current flows only when
the switch is pushed
into sound energy
2. Circuit Circuitdiagram
Learner’s Book.

Switch Name Symbol
Rocker switch
Toggle switch
Push switch
Slide switch
4. (b)
5. b
6. c
7. b
8. b
9. b
10. c
Learner’s Book.

11. b
12. a
13. a
14. b
15. c
16. d
17. Name the switch Illustration of switch Draw the symbol
Double-throw switch
Push switch
Single pole, single throw

switch
Slide switch
Double pole, double throw
18. Symbol Drawing Symbol name

Motor
Touch or moisture detector
resistor
Light dependent resistor
Learner’s Book.

Polarized capacitor
19. a) OR
b) AND
Possible answer: OR gate
Input output
A B Z
0 0 0
0 1 1
1 0 1
1 1 1
Possible answer: AND Gate

Input Output
A B Z
0 0 0
0 1 0
1 0 0
1 1 1
20. How to determine the resistance of a resistor
Colour Band 1 Band 2 Zeros

Black 0 0
Brown 1 1 0
Red 2 2 00
Orange 3 3 000
Yellow 4 4 0000
Green 5 5 00000
Blue 6 6 000000
Violet 7 7 0000000
Grey 8 8 00000000
White 9 9 000000000
21 a two
21 b decimal multiplier
Learner’s Book.

Module 4
Types of plastic
Plastic product Type of plastic used to SPI Identification
manufacture product code
Learner’s Book.

Module 4
Memorandum – Types of plastic

Plastic product Type of plastic used to manufacture SPI Identification
product code
HDPE (high density polyethylene):
milk bottles, detergent bottles, oil
bottles, toys, plastic bags
2
Other: This code indicates that the

item is made with a resin other than
the six listed above, or a combination
of different
7
resins.
PET (polyethylene terephthalate):

plastic colddrink bottles,
water bottles, beer bottles,
mouthwash bottles and many 1
more
HDPE (high density polyethylene):

milk bottles, detergent
bottles, oil bottles, toys, plastic bags
2
PP (polypropylene): margarine and

yoghurt containers, caps
for containers, wrapping to replace
cellophane
5
PVC (polyvinyl chloride): food wrap,

vegetable oil bottles,
blister packaging, medical products
3
Learner’s Book.

Section A: Preserving metals

1. Explain each of the following terms. [6]
A Galvanising
B Electroplating
C Oxidation
2. List five industries where metals are used, and state a common metal product used in
each of these industries. [5]
3. List three main steps involved in the process of hot tip galvanising. [3]
4. Match the galvanising process in Column A with the purpose of the process in Column B.
Write only the letter of the alphabet in the Answer column. [6]
Column A Column B Answer
1 Metal is placed in a A Creates a protective coating to prevent
hydrochloric or sulfuric steel from oxidising before galvanising
solution begins
2 Metal is lowered into as B Removes oxides
caustic bath solution
3 Fluxing of metal C Removes dirt, oil and grease
5. List the factors that need to be taken into consideration when choosing a suitable paint
to protect metal. [4]
6. Draw a simple flow diagram to show the galvanising process. [12]
7. Provide labels for the apparatus marked A to E in the electroplating kit shown below. [5]
D
B
C E
Section B: Food preservation

1. Draw an annotated diagram showing how the Nguni people used indigenous technology to
preserve grain. [12]
2. Explain the role of carbon dioxide in indigenous food preservation. [3]
3. Draw a simple flow diagram explaining how vegetables can be pickled. [6]
Learner’s Book.

Section C : Plastics
1. Explain in your own words each of the following commonly used terms associated with
the manufacture and recycling of plastics. [6]
A The three Rs
B Closed loop recycling
C SDI Codes
2. Identify the type of plastic used to manufacture each of the following types of plastic
products and draw the correct SDI symbol for the type of plastic used. [10]
Plastic product Type of plastic used to SPI identification code
manufacture product
3. Tabulate the difference between:

A Thermoplastics and thermosetting plastics
B Blow moulding and compression moulding [8]
4. Draw a systems diagram showing the process of using waste plastic to manufacture
pellets for reuse. [8]
Learner’s Book.

An example of a generic analytical rubric to
assess design capability in a mini-PAT
Levels of competence
Developing
Exemplary Competent but not yet Progressing
mastering
5 4 3 2 1
Generate Uses drawings Progression of Design ideas Simple sketch Drawing a
and develop reflectively to ideas across are generated showing picture not
design ideas generate new or within but not object to be designing a
ideas drawings developed made product
Explore the Combining Using Recording Stereotypical Design
possibilities novel drawings possible response, possibilities
of the solutions to develop creative showing are not
problem/need to produce novel design solution(s) to little creative addressed in
innovative solution(s) the task thought the drawing
design
Address the Task Task Records way Drawings Minimal
constraints constraints constraints to address show some understanding
of the treated considered task and/or understanding of task/user
problem/need as part of as the design client needs of task needs
iterative proceeds and wants constraints
process
Plan the Ideas about Ideas about Overall Little Appearance of
look of the finishing finishing are decoration consideration product is not
product develop within added to scheme of final considered
overall design design whilst considered appearance of
drawing product
Communicate Clear enough Conveys sense Conveys Simple Use of
design ideas for somebody of the object some sense unlabelled narrative or
else to make to be made, of the object sketch(es); other drawing
the product e.g. working to be made, relying genre
diagram e.g. indicates on shared
materials meanings
Plan Construc- Drawing Drawing Minimal Not planning
construction tional issues demonstrates indicates consideration to make the
considered en consideration some of object drawn
route to final of consideration construction
design construction of whilst drawing
construction
Evaluate Changes Decisions Considered Minimal Yet to define
while drawing made a result made about and rejected a evaluation at the design
of considering products range of ideas drawing phase task
design whilst drawing
drawings
Provide a Using Clear Object is one Product Making an
basis for drawings as development of the ideas relates object is seen
making a resource path through drawn to ideas as separate
during making drawing into recorded in new activity
making the drawing
Comments to improve the learner’s performance in design capability:
Learner’s Book.

Module 4 – Assessment memorandum
Section A : Preserving metals

1. Explain each of the following terms. [6]
A Galvanising – Is the process of preserving a corrosive metal, such
as steel, with a non-corrosive metal, such as zinc.
B Electroplating – Is the process commonly used to preserve metal by
applying a fine metal coating to the metal object.
C Oxidation – Is the interaction of a substance with oxygen.
2. List five industries where metals are used, and state a common
metal product used in each of these industries. [5]
3. List three main steps involved in the process of galvanising. [3]
Surface preparation, galvanising, post-treatment
4. Match the galvanising process in Column A with the purpose of the
process in Column B. Write only the letter of the alphabet in the
Answer Column. [6]
Column A Column B Answer
1 Metal is placed in A Creates a protective C
a hydrochloric or coating to prevent steel
sulfuric solution. from oxidising before
galvanising begins
2 Metal is lowered into a B Removes oxides B
caustic bath solution
3 Fluxing of metal C Removes dirt, oil and A
grease
5. List the factors that need to be taken into consideration when

choosing a suitable paint to protect metal. [4]
The condition of the metal structure, the type of metal that needs to be
preserved, the life expectancy of the metal and the environment where
the structure is to be used.
6. Draw a simple flow diagram to show the galvanising process. [12]
Mark allocation:
1mark for heading
1 mark for indicating start and finish points
1 mark for each step
Learner’s Book.

Heading : Flow diagram showing the galvanising process
Start
➡ Caustic cleaning
➧ ➧ ➧ ➧ ➧ ➧ ➧ ➧
Rinsing
Pickling
Rinsing
Flux solution
Drying
Zinc bath
Cooling
➡
Finish Inspection
7. Provide labels for the apparatus marked A to E in the

electroplating kit shown below. [5]
D
B
C E
Answers
A –Battery
B – Sulfate ions
C – Copper electrode
D – Copper ions
E – Nickel electrode
Section B : Food preservation

1. Draw an annotated diagram showing how the Nguni people
used indigenous technology to preserve grain. [12]
Award the learner marks for the following details shown in the
diagram.
A – Pit is dug in the middle of a cattle kraal and lined with moist
clay
B – Fresh maize kernels are placed in the pit
C – Entrance of the pit is covered with a large stone and covered
with cow dung mixed with clay
Learner’s Book.

D – Grain kernels that come into contact with the damp clay
ferment and release CO2 into the pit, which prevents fungi
and bacteria from developing
E – When the grain is needed, the cover is removed and left open
for a few hours to let all the CO2 escape
F – A small child is lowed into the pit to retrieve the grain.
6 marks for correct label on drawing
6 marks for explanation
2. Explain the role of carbon dioxide in indigenous food
preservation. [3]
Grain kernels that come into contact with the damp clay begin to
ferment and release carbon dioxide gas (CO2) into the sealed grain
pit, which prevents bacteria and fungi from developing. The sealed lid
prevents insects and rodents from entering and protects the grain.
3. Draw a simple flow diagram explaining how vegetables can be
pickled. [6]
Start
➡ Pickling jar sterilised and left to dry
➧
Fresh vegetables cleaned, dried and

mixed with spices and condiments
➧ ➧
Vegetables placed in sterilised jar
Jar filled with vinegar, oil or a

combination of vinegar and oil
➧
➡ Vegetables in jar are allowed to

Finish ferment until desired texture and
taste is attained
Section C : Plastics
1. Explain in your own words each of the following commonly used
terms associated with the manufacture and recycling of plastics.[6]
A The three Rs – Reuse, reduce and recycle plastic products
whenever possible so that less plastic ends up in landfill sites.
B Closed loop recycling – A production system in which the waste
or byproduct of one process or product is used in making another
product.
C SDI codes – Codes developed by the Society of the Plastics
Industry to help people classify plastics into the different types to
make recycling easier.
2. Identify the type of plastic used to manufacture each of the
following types of plastic products and draw the correct SDI
symbol for the type of plastic used. [10]
Learner’s Book.

Plastic product Type of plastic used to SPI identification code
manufacture product
PET
LDPE
PP
HDPE
PVC
3. Tabulate the difference between:

A Thermoplastics and thermosetting plastics
B Blow moulding and compression moulding [8]
Learner’s Book.

Thermoplastics Thermosetting plastics
Thermoplastics are the plastics Thermosetting plastics can
that do not undergo chemical melt and take shape once. They
change in their composition cannot be returned to their
when heated and can be liquid form, i.e. the process
moulded again and again. involved in thermosetting
plastics cannot be reversed.
Blow moulding Compression moulding
Blow moulding is when a melted Compression moulding is when
polymer material is placed into a polymer is placed on the
a mould, air is injected into bottom half of a compression
the cavity, which pushes the mould and the top half is lowed
polymer into the desired shape. onto the bottom half pushing
the polymer into the desired
shape.
4. Draw a systems diagram showing the process of using waste
plastic to manufacture pellets for reuse. [8]
Input ➧ Process ➧ Output
Collected Washed to remove New plastic

PET bottles residual pellets
placed in large
Cleaned using corrosive
cleaning baths
solution to remove
chemicals and glues
Plastic shreds placed in
large tumble dryers to
remove moisture
Mark allocation:
1 mark each for each aspect of the systems diagram [3]
1 mark each for each correct point [5]
Learner’s Book.

Section F: Documents
You may add any other documents you receive in this section and list them for
easy reference.
TOPIC TERM 3 E1
Technology_Grade 9_TG Section F.indd 1 2013/07/02 4:05 PM

Technology_Grade 9_TG Section F.indd 2 2013/07/02 4:05 PM
Grade
Study & Master
9 Technology
Study & Master Technology has been specially developed by
experienced educators to meet all the requirements of the
Curriculum and Assessment Policy Statement (CAPS). This new
and easy-to-use course not only helps learners master essential
content and skills in the subject, but gives them the best possible
foundation on which to develop and build their Technology
knowledge and understanding.
The comprehensive Learner’s Book:

• provides an overview of content, concepts and skills covered
in each term
• supplies activities that develop learners’ skills and
understanding of each of the topics specified by CAPS
• includes investigations, and practical tasks, as well as Formal
Assessment Tasks in the form of Mini-PATs for each term
• features ‘Did you know?’ boxes with interesting additional
information and ‘Safety tip’ and hint boxes that provide
guidance on how to do technology tasks safely and easily
• includes a glossary of key words to help with the
understanding of new terms and concepts.
The innovative Teacher’s Guide includes:

• an expanded contents page and a work schedule for the year
• guidance on the teaching of each lesson and on each form of
assessment
• step-by-step support in the teaching of activities and the
carrying out of practical tasks
• photocopiable record sheets and templates, as well as
additional worksheets to support your teaching.
Ria de Jager has a Masters Degree in Technology Education. She is Deputy Chief Education Specialist
in Technology in KZN and Chairperson of the SA Technology Association. Lin Bassett has taught
Technology at both government and private schools and presented various workshops at Technology
conferences. Barbara Munsami is subject head (Technology) at Marist College and has facilitated
workshops for both NGOs and DBE. Lynn Pocock has trained in Technology teaching methods, taught
at a pilot school for Technology in 2005 and has been working in Special Needs and Remedial Schools
for over a decade. Neel Ramdutt has an MEd in Educational Studies and Multimedia Design as well as a
Certificate in Technology Education. He is is now Deputy Chief Education Specialist (Technical Subjects /
Technology) at the KZN Head Office.
www.cup.co.za
SM_Technology_G9_TG_CAPS_ENG.indd 2 2013/07/02 1:58 PM

Study Master Technology Grade 9 Teacher S Guide

Uploaded by

Copyright:

Available Formats

Study Master Technology Grade 9 Teacher S Guide

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Study Master Technology Grade 9 Teacher S Guide

Uploaded by

Copyright:

Available Formats

Technology

Ria de Jager • Lin Bassett • Neel Ramdutt

SM_Technology_G9_TG_CAPS_ENG.indd 1 2013/07/02 1:58 PM

Ria de Jager • Lin Bassett • Neel Ramdutt

Cambridge, New York, Melbourne, Madrid, Cape Town,

Cambridge University Press

© Cambridge University Press 2013

This publication is in copyright. Subject to statutory exception

First published 2013

Editor: Fairuz Parker

The photocopy masters in this publication may be photocopied or

Technology_Grade 9 Prelims.indd 2 2013/07/02 3:32 PM

Section D: Teaching guidelines D1

Section E: Photocopiable resources E1

Technology_Grade 9 Prelims.indd 3 2013/07/02 3:32 PM

7 Lesson 14 Activity 21 Working drawings Drawing 97 D43

Curriculum and Assessment Policy Statement (CAPS) A3

Technology_Grade 9 Prelims.indd 1 2013/07/02 3:32 PM

Curriculum and Assessment Policy Statement

Technology_Grade 9 Prelims.indd 3 2013/07/02 3:32 PM

The purpose of the National Curriculum Statement

Technology_Grade 9 Prelims.indd 4 2013/07/02 3:32 PM

High knowledge and high skills

Human rights, inclusivity, environmental and social

Technology_Grade 9 Prelims.indd 5 2013/07/02 3:32 PM

Credibility, quality and efficiency

Qualities and skills of learners

Technology_Grade 9 Prelims.indd 6 2013/07/02 3:32 PM

What should this mean in your classroom? In this series of books,

Partial sight or blindness: For partially sighted learners who find it

Technology_Grade 9 Prelims.indd 7 2013/07/02 3:32 PM

Impaired social skills: The nature of these difficulties varies, but

Look out for a learner who:

Technology_Grade 9 Prelims.indd 8 2013/07/02 3:32 PM

Please note that:

Extreme poverty: This barrier to learning requires extreme sensitivity

Technology_Grade 9 Prelims.indd 9 2013/07/02 3:32 PM

Technology in the school curriculum

A10 SECTION A INTRODUCTION

Technology_Grade 9 Prelims.indd 10 2013/07/02 3:32 PM

Unique features and scope

Technology will give learners the opportunity to learn:

SECTION A INTRODUCTION A11

Technology_Grade 9 Prelims.indd 11 2013/07/02 3:32 PM

The importance of design in Technology education

A12 SECTION A INTRODUCTION

Technology_Grade 9 Prelims.indd 12 2013/07/02 3:32 PM

Examples of careers that use design:

Designers need to have...

Teaching methodology (how tasks will be

SECTION A INTRODUCTION A13

Technology_Grade 9 Prelims.indd 13 2013/07/02 3:32 PM

Designing, making and evaluating.

As learners progress they should be able to demonstrate increasing

Criteria for teaching and assessing design features:

Note on drawing: The Grade 9 learner must be able to identify and

In Grades 7–9 Technology, drawing is separated into three fields:

A14 SECTION A INTRODUCTION

Technology_Grade 9 Prelims.indd 14 2013/07/02 3:32 PM

Section D: Teaching guidelines D1

Section E: Photocopiable resources E1