Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 29 views

    SCR As A Switch

    Uploaded by

    Michael Gitau

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    SCR As A Switch

    Uploaded by

    Michael Gitau
    29 views2 pages

    Original Title

    SCR as a Switch

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    29 views2 pages

    SCR As A Switch

    Uploaded by

    Michael Gitau

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 2

    SCR as a Switch

    The SCR has only two states, namely; ON state and OFF state and no state in between. When
    appropriate gate current is passed, the SCR starts conducting heavily and remains in this
    position indefinitely even if gate voltage is removed. This corresponds to the ON condition.
    However, when the anode current is reduced to the holding current, the SCR is turned OFF. It
    is clear that behaviour of SCR is similar to a mechanical switch. As SCR is an electronic
    device, therefore, it is more appropriate to call it an electronic switch.
    Advantages of SCR as a switch. An SCR has the following advantages over a mechanical or
    electromechanical switch (relay):
    i. It has no moving parts. Consequently, it gives noiseless operation at high efficiency.
    ii. The switching speed is very high up to 109 operations per second.
    iii. It permits control over large current (30–100 A) in the load by means of a small gate
    current (a few mA).
    iv. It has small size and gives trouble free service.

    Important Terms
    The following terms are much used in the study of SCR:
    (i) Breakover voltage. It is the minimum forward voltage, gate being open, at which SCR
    starts conducting heavily i.e. turned on.
    Thus, if the breakover voltage of an SCR is 200 V, it means that it can block a forward
    voltage (i.e. SCR remains open) as long as the supply voltage is less than 200 V. If the supply
    voltage is more than this value, then SCR will be turned on. In practice, the SCR is operated
    with supply voltage less than breakover voltage and it is then turned on by means of a small
    voltage applied to the gate. Commercially available SCRs have breakover voltages from
    about 50 V to 500 V.
    (ii) Peak reverse voltage (PRV). It is the maximum reverse voltage (cathode positive w.r.t.
    anode) that can be applied to an SCR without conducting in the reverse direction.
    Peak reverse voltage (PRV) is an important consideration while connecting an SCR in an a.c.
    circuit. During the negative half of a.c. supply, reverse voltage is applied across SCR. If PRV
    is exceeded, there may be avalanche breakdown and the SCR will be damaged if the external
    circuit does not limit the current. Commercially available SCRs have PRV ratings upto 2.5
    kV.
    (iii) Holding current. It is the maximum anode current, gate being open, at which SCR is
    turned off from ON conditions.
    As discussed earlier, when SCR is in the conducting state, it cannot be turned OFF even if
    gate voltage is removed. The only way to turn off or open the SCR is to reduce the supply
    voltage to almost zero at which point the internal transistor comes out of saturation and opens
    the SCR. The anode current under this condition is very small (a few mA) and is called
    holding current. Thus, if an SCR has a holding current of 5mA, it means that if anode current
    is made less than 5mA, then SCR will be turned off.
    (iv) Forward current rating. It is the maximum anode current that an SCR is capable of
    passing without destruction.
    Every SCR has a safe value of forward current which it can conduct. If the value of current
    exceeds this value, the SCR may be destroyed due to intensive heating at the junctions. For
    example, if an SCR has a forward current rating of 40A, it means that the SCR can safely
    carry only 40 A. Any attempt to exceed this value will result in the destruction of the SCR.
    Commercially available SCRs have forward current ratings from about 30A to 100A.
    (v) Circuit fusing (I2t) rating. It is the product of square of forward surge current and the
    time of duration of the surge i.e.,
    Circuit fusing rating = I2t
    The circuit fusing rating indicates the maximum forward surge current capability of SCR. For
    example, consider an SCR having circuit fusing rating of 90 A2s. If this rating is exceeded in
    the SCR circuit, the device will be destroyed by excessive power dissipation.

    You might also like