Location via proxy:   [ UP ]  
[Report a bug]   [Manage cookies]                
Scribd Logo
Upload

Welcome to Scribd!

  • 6 views

    Polysure HDPE R0150S

    Uploaded by

    yadavgirija30

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd

    Polysure HDPE R0150S

    Uploaded by

    yadavgirija30
    6 views1 page

    Original Title

    246554668_Polysure_HDPE_R0150S

    Copyright

    © © All Rights Reserved

    Available Formats

    PDF, TXT or read online from Scribd

    Did you find this document useful?

    Is this content inappropriate?

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    6 views1 page

    Polysure HDPE R0150S

    Uploaded by

    yadavgirija30

    Copyright:

    © All Rights Reserved
    Download as PDF, TXT or read online from Scribd
    Download as pdf or txt
    of 1

    Provisional Technical Datasheet

    R0150S Polysure HDPE Raffia

    Product Characteristics:
    Polysure R0150S is 1-butene comonomer based High Density Polyethylene, produced by Gas Phase – UNIPOLTM
    PE technology, suitable for Raffia tape Extrusion process. R0150S resin offers excellent processability with low
    water carry over, good stretchability, superior mechanicals, and resistance to fibrillation.

    Recommended Applications:
    Woven sacks, Raffia, Tarpaulins

    Typical Properties:
    Sr. No. Property Test Method Unit Value*
    1 Melt Flow Index (190°C & 2.16 kg) ASTM D1238 g/10 min 1
    2 Density (23°C) ASTM D1505 g/cc 0.950
    3 Tensile Strength at Yield, Type IV Specimen MPa 25
    ASTM D638
    4 Tensile Strength at Break, Type IV Specimen MPa 35
    (50 mm / min)
    5 Tensile Elongation at Break, Type IV Specimen % 1000
    6 Flexural Modulus (1% Secant) ASTM D790A MPa 1200
    7 Notched Izod Impact Strength (23°C) ASTM D256 J/m 400
    8 Vicat Softening Point (10N) ASTM D1525 °C 123
    * All the mechanical properties are determined on Compression Molded Test Specimen, prepared in accordance with ASTM D4703

    Processing Guidelines:
    • Barrel Temperature : 190 - 240°C
    • Die Temperature : 220 - 240°C
    • Quench Temperature : 25 - 30°C

    Storage & Handling:


    Bags should be stored in dry & dust free environment at temperature below 50°C and Prevent from direct exposure
    to sunlight & heat to avoid quality deterioration.

    Regulatory Requirements:
    R0150S to be manufactured complying the requirements specified in IS 10146 on “Specification for Polyethylene
    for its safe in contact with Foodstuff, Pharmaceutical & Drinking water”. Furthermore, the Additives added in this
    grade formulation compiles to the “Positive list of constituents for Polypropylene, Polyethylene and their
    Copolymers for its safe use in contact with Foodstuffs & Pharmaceuticals' as laid down under IS 16738:2018. In
    general, the additives & constituents used in the grade are in line with requirement laid down under FDA: CFR
    Title 21,177.1520, Olefin Polymers.

    Updated as of May 2021

    Disclaimer: The information & data presented herein are typical values & should not be considered as specification and may be used as guideline only. HMEL does not undertake any
    responsibility for any outcome or results from the adoption or replication of the above-mentioned data & information there on for possible use for various applications. HMEL reserves the
    right to change the information & data without any prior notice or information. The user will solely be responsible for any process/product usage.
    HPCL-Mittal Energy Limited (HMEL), INOX Tower, Plot No.17, Sector-16A, Noida – 201301 (U.P), India. Tel: 0120-4634500. Corporate Site: www.hmel.in

    You might also like