Benq 9h.j4s77.14e

Applicable Country & Regions:
All Regions
Product Service Manual – Level 2
Service Manual for BenQ:

Projector/MW814ST
< 9H.J4S77.000>
Version: 00a
Date:2011/05/12
Notice:
For RO to input specific “Legal Requirement” in specific NS regarding to responsibility and liability
statements.
http://esupport.benq.com,, to ensure that you have the most
Please check BenQ’s eSupport web site, http://esupport.benq.com
recent version of this manual.
First Edition (May 2011)

© Copyright BenQ Corporation 2009. All Right Reserved.
1
Content Index
1. Abbreviations & Acronyms ................................................................
.....................................................................
..................................... 3
2. About This Manual................................................................
..................................................................................
.................................................. 4
2.1 Trademark ................................................................................................................................. 4
2.2 Introduction.............................................................................................................................. 4
2.3 Important Service Information ............................................................................................... 4
2.4 Safety Notice ............................................................................................................................. 5
2.5 Compliance Statement ............................................................................................................. 5
2.6 General Descriptions ................................................................................................................ 5
2.7 Related Service Information .................................................................................................... 5
3. Product Overview ................................................................
....................................................................................
.................................................... 6
3.1 Specification Overview ............................................................................................................. 7
3.2 Packing .................................................................................................................................... 24
3.3 Customer Acceptance ............................................................................................................. 34
4. Level 1 Cosmetic / Appearance / Alignment Service ............................. 37
4.1 Cosmetic / Appearance Inspection Criteria .......................................................................... 37
4.2 OPERATIONAL INSPECTION CRITERIA.......................................................................... 40
4.3 Software/Firmware Upgrade Process ..................................................................................... 44
4.4 Method to enter factory menu ............................................................................................... 54
4.5 RS-232 connection ................................................................................................................. 55
4.6 Adjustment / Alignment Procedure ....................................................................................... 57
5. Level 2 Circuit Board and Standard Parts Replacement ....................... 61
5.1 Product Exploded View .......................................................................................................... 61
5.2 Product Disassembly / Assembly ........................................................................................... 65
5.3 Module Assembly Key Point - Optical Engine ...................................................................... 68
5.4 Module Assembly Key Point - Mechanical ............................................................................ 81
5.5 Block Diagram ........................................................................................................................ 81
5.6 Trouble shooting ..................................................................................................................... 97
Appendix 1 – Screw List / Torque ...........................................................
........................................................... 106
Appendix 2 - Code List: IR / RS232 / DDC Data ....................................
.................................... 108
Appendix 3 – Ceiling Mount Drawing ...................................................
................................................... 117
2
1. Abbreviations & Acronyms
A
A/D Analog to Digital
B
BenQ BenQ Corporation
C
C/W Color Wheel
CM Concave Mirror
D
DLP Digital Light Processing / Texas Instruments®
DMD Digital Micro mirror Device
DVI Digital Video Interface
DVI-I Digital Video Interface-Integrated
P
PL Projection Lens
POM Pond of Mirrors
R
Interface Between Data terminal Equipment and
RS232 Data Communications Equipment Employing
Serial Binary Data Interchange
S
Super Video Graphics Array, A screen resolution
SVGA
of 800 x 600 pixels.
Super XGA. A screen resolution of 1280x1024
SXGA
pixels.
V
Video Graphics Array. A screen resolution of
VGA
640x480 pixels.
X
XGA A screen resolution of 1024x768 pixels.
3
2. About This Manual
This manual contains information about maintenance and service of BenQ products. Use this manual
to perform diagnostics tests, troubleshoot problems, and align the BenQ product.
Important
Only trained service personnel who are familiar with this BenQ Product shall perform
service or maintenance to it. Before performing any maintenance or service, the
engineer MUST read the “Important Safety Information”
2.1 Trademark
The following terms are trademarks of BenQ Corporation:
BenQ
Other companies, products, or service names may be the trademarks of their respective companies.
2.2 Introduction
This section contains general service information, please read through carefully. It should be stored
for easy access place.
2.3 Important Service Information

RoHS (2002/95/EC) Requirements – Applied to all countries require RoHS.
The RoHS (Restriction of Hazardous Substance in Electrical and Electronic Equipment Directive) is a
legal requirement by EU (European Union) for the global electronics industry which sold in EU and
some counties also require this requirement. Any electrical and electronics products launched in the
market after June 2006 should meet this RoHS requirements. Products launched in the market
before June 2006 are not required to compliant with RoHS parts. If the original parts are not RoHS
complaints, the replacement parts can be non ROHS complaints, but if the original parts are RoHS
compliant, the replacement parts MUST be RoHS complaints.
If the product service or maintenance require replacing any parts, please confirming the RoHS
requirement before replace them.
4
2.4 Safety Notice
1 Make sure your working environment is dry and clean, and meets all government safety
requirements.
2 Ensure that other persons are safe while you are servicing the product.
3 DO NOT perform any action that may cause a hazard to the customer or make the product
unsafe.
4 Use proper safety devices to ensure your personal safety.
5 Always use approved tools and test equipment for servicing.
6 Never assume the product’s power is disconnected from the mains power supply. Check that it is
disconnected before opening the product’s cabinet.
7 Modules containing electrical components are sensitive to electrostatic discharge (ESD). Follow
ESD safety procedures while handling these parts.
8 Some products contain more than one battery. Do not disassemble any battery, or expose it to
high temperatures such as throwing into fire or it may explode.
9 Refer to government requirements for battery recycling or disposal.
2.5 Compliance Statement

Caution: This Optical Storage Product contains a Laser device. Refer to the product specifications and
your local Laser Safety Compliance Requirements.
2.6 General Descriptions

This Service Manual contains general information. There are 2 levels of service:
Level 1: Cosmetic / Appearance / Alignment Service
Level 2: Circuit Board or Standard Parts Replacement
2.7 Related Service Information

Service Web Site
BenQ Global Service Website: http://www.benq.com/support/
eSupport Website: http://esupport.benq.com/v2
5
3. Product Overview
The projector consists of DLP projector controller, Lamp controller, Power supply system, and
System cooling controller. The DLP controller captures digital PC data and video data and then
converts them into the DMD display device. The Lamp controller dominates the lamp’s power and
synchronizes its frequency with color display sequence. The Power supply unit controls the AC line
power factor and converts primary voltage to secondary low voltages for digital board. The System
cooling controller drives the airflow to quench the lamp’s heat and electrical component’s heat.
Specification Overview
1.0 Panel Information
2.0 Projection Lens Specification
3.0 Optical Specification
4.0 Lamp Specification
5.0 Mechanical Specification
6.0 Packaging
7.0 Thermal Specification
8.0 Power Requirements
9.0 Compatibility
10.0 User Interface
11.0 Regulatory
12.0 Reliability
13.0 Other Feature
Input / Output Connectors
1. Input Terminals
2. Output Terminals
3. Control Terminals and Interface
Accessories
Environmental
Electrical
Electrical Specification
Power Supply Specification
UI Specification
6
3.1 Specification Overview
Specification Overview
MW814ST Version: 01
Item Specification
1.Panel Information
1.1 Panel Type 0.65” WXGA 2xLVDS 450 DMD
1.2 Package Type 450 series
1.3 Size 0.65”
1.4 Pixels 1280(H) x 800(V)
1.5 Color Depth 30 Bits (1.07 Billion Colors)
1.6 Driver Type DDP 2431
1.7 Panel Pixel Quality Follow TI spec.
1.8 Image Imperfection Follow TI spec.
2. Projection Lens Specification (For Reference)
Wide Tele
2.1 F/#
2.59 NA
2.2 Zoom Ratio Fixed
2.3 Throw Ratio 0.49 (95"±3%@ 1m)
2.4 True Zoom NA
Wide: Tele:
2.5 Focal Length
6.95 mm NA
2.6 Offset 110%+/-5%
2.7 Visible Focus Range 0.75 to 1.6m
2.8 Clearly Focus Range 0.75 to 1.6m
2.9 Keystone Distortion <1%
2.9 TV Distortion <1%
2.10 Screen Distortion |A| <= 3.5 mm, |B| <= 3.5 mm, |C| <=3.5 mm @ 60”
2.11 Zoom Ring Torque N.A. (Follow Vendor Lens SPEC)
2.12 Focus Ring Torque 250~450g (Follow Vendor Lens SPEC)
2.13 Center Position Shift(W-T)
N.A.
(Video Projector only)
2.14 Zoom&Focus shaking level Follow typical sample (When needed)
2.15 Lens Shift Shaking Level N.A.
Center @ 49” All other area
R-G <2/3 pixel <1.0 pixel
2.16 Lateral Color
B-G <2/3 pixel <1.0 pixel
R-B <1.0 pixel <1.0 pixel
6-Seg. (RYWCBG), ‘10 CW
2.17 Color wheel segment
W:60 C:30 B:75 G:85 R:80 Y:30
2.18 Color wheel speed 2x
3.Optical Specification
Test under 70” (diagonal) image size with Wide projection lens position.
Reference Meter: Vendor Factory CL-200 Meter (SN head:81531011, body:82521013)
Normal: Minimum 2000 lm
3.1 ANSI Brightness (Typical 2250 lm, only for reference)
ECO: Minimum 1545 lm (For reference)
3.2 ANSI uniformity Minimum 45%
3.3 JBMA Uniformity Minimum 65%
3.4 ANSI Contrast Minimum 150:1
3.5 FOFO Contrast Minimum 2400:1 (w/ WCE)
3.7 FOFO Contrast with DB N.A.
3.8 Focus Quality
7
(1) If pattern can be uniformly focused – not worse than limit
sample – then pass!
3.8.1 区 Pattern
Limit Sample: TBD
(2) If it’s difficult to judge, then check 3.8.2
3.8.2 R G B
Defocus (Maximum) 3.0 3.0 3.0
Flare (Maximum) 4.0 4.0 4.0
3.9 Focus unbalance Max. 60cm
Color x y
White 0.315±0.04 0.364±0.04
3.10 Color Coordinate
Red 0.636±0.04 0.355±0.04
(Confirm at PVT stage)
Green 0.330±0.04 0.571±0.04
Blue 0.145±0.03 0.073±0.03
△uv
Color
△v
3.11 Color Uniformity White ≦0.02
(Confirm at PVT stage) Red ≦0.03
Green ≦0.02
Blue ≦0.02
3.12 Color Gamut(Compare to NTSC) Typical 60%
△△0.5 lux compared with center point @ full black pattern
within 78” (Diagonal at 0.485m).
3.13 Light Leakage in AA This light-leakage is only described as the spot light with
obvious shape. The uniformity difference of black pattern is
not included.
≦0.5 lux, @ full black pattern with 78”~90“(Diagonal at
3.14 Light Leakage out of AA 0.485m)
(Except DMD Defect)
3.15 Ghost Ghost Contrast > (Confirm at EVT2 stage)
3.16 Lens Shift Speed(sec)
N.A.
(only for motorized len shift)
3.17 Defect (Color Band, Dark Corner, Follow limited sample (When needed).
Dark band)
3.18 Preset mode setting Refer appendix E
4.Lamp Specification
4.1 Lamp SHP220W
4.2 Lamp Sync Type DC Lamp
4.3 Lamp Flick Follow limited sample (When needed).
Normal Mode 220W
4.4 Lamp Power
ECO Mode 170W
5. Mechanical Specification
5.1 Color & Texture specifications Refer to ID document for details
5.2 Physical Dimensions(Width X
287.3 x 232.6 x 114.4 mm
Depth X Height)
5.3 Gross Weight 2.7kg
5.4 Security Slot Kensington compatible slot 20Kg break away force
5.5 Lens Cover Detached lens cover
Fast adjustable foot in front, Adjustable foot in rear. Front/
5.6 Adjustment Feet
Rear foot Tilt: 0-6∘,Right/Left: +2.2∘/-0.5∘
Match BenQ’s ceiling mount required.
5.7 Ceiling Mounting
Use the same mounting as current shipping projectors.
All color of screws should similar with the plastic color which
5.8 Screws
close it.
5.9 During PVT stage, limited sample N/A
8
of color and texture should be
approved by BenQ industrial
designer and mechanical
engineer.
6. Packaging
6.1 Box Dimension Refer to packing description (internal :Refer to B405 document )
6.2 Net Weight (Esti.) ≤ 2.7kg
6.3 Gross Weight (Esti.) < 3.5 kg (Including Accessories, Projector)
6.4 Container Loading (40') Refer to packing description (internal :Refer to B405 document )
6.5 Container Loading (20') Refer to packing description (internal :Refer to B405 document )
6.6 Packaging Conceptual Refer to packing description (internal :Refer to B405 document )
6.7 Container Layout Refer to packing description (internal :Refer to B405 document )
6.8 Cushion Orientation Refer to packing description (internal :Refer to B405 document )
6.9 Cushion Material EPE
6.10 Box Compression Test N/A
6.11 Carton Artwork Refer Packing Description and Appearance Description
7. Thermal Specification
Mechanical component temperature at ambience 0~40℃
Normal surface:
7.1 Surface held or touched for Metal< 60 ℃ Plastic< 85 ℃
short periods Bottom surface @25℃
Metal< 55 ℃ Plastic< 70 ℃
Metal Plastic
7.2 Surface which my be touched
< 70 ℃ < 95 ℃
7.3 Exhaust Air < 95 ℃
Normal mode: 35dBA@ 25°C(table center)
Typical
Eco mode: 29dBA @ 25°C(table center)
7.4 Audible Noise Level
Normal mode: 37dBA@ 25°C(table center)
Max.
Eco mode: 31dBA @ 25°C(table center)
7.5 Fan Numbers 2
8.0 Power Requirements
8.1 Power Supply (Normal)
Max. 335W
1W Max. at 100 ~ 240VAC
Standby
8.2 Power consumption (disable loop through, LAN control, audio out)
Normal Typical 300W@110Vac
ECO Typical 239W@110Vac
8.3 Power Connector IEC 60320 C14
8.4 Power Switch No
9.0 Compatibility
9.1 Data Compatibility
9.1.1 RGB Digital Refer to 2.1.4 HDMI/DVI Input
640x480 @60/72/75/85Hz
720x400 @70Hz
800x600 @60/72/75/85/120Hz
1024 x 576@60Hz
1024 x 600@65Hz
1024x768 @60/70/75/85/120Hz
1152x864@75Hz
1280x768@60Hz
1280 x 800@60/75/85/120Hz
1280 x 1024@60/75/85Hz
1280 x 960@60/85Hz
1360x768@60Hz
9
1440 x 900@60Hz
1400X1050@60Hz
1600x1200@60Hz
1680x1050@60Hz
1920x1200@60Hz
9.1.2 RGB Analog Refer to 2.1.5 PC Input
640x480 @60/72/75/85Hz
720x400 @70Hz
800x600 @60/72/75/85Hz/120Hz
1024x768 @60/70/75/85Hz/120Hz
1024 x 576@60Hz
1024 x 600@65Hz
1152x864@75Hz
1280x768@60Hz
1280 x 800@60/75/85/120Hz
1280 x 1024@60/75/85Hz
1280 x 960@60/85Hz
1360x768@60Hz
1440 x 900@60Hz
1400X1050@60Hz
1600x1200@60Hz
1680x1050@60Hz
9.1.3 Macintosh
MAC 13/16/19/21
9.2 Video Compatibility
9.2.1 SDTV 480i/576i
9.2.2 EDTV 480P/576P
9.2.3 HDTV 720@50P/60P,1080@50i/60i/50p/60p/24p/25p/30p
NTSC/ NTSC4.43/ PAL (Including PAL-M, PAL-N)/ SECAM/
9.2.4 Video
PAL60/
9.3 Frequency
9.3.1 H-Sync 31~102KHz
9.3.2 V-Sync 23 ~ 120 Hz
9.4 DDC EDID 1.3
10.0 User Interface
10 Keys:
10.1 Operator Keypad Power ; Source ;Auto ; Blank ; Mode/Enter ; Menu/Exit ; Right/
Panel Key Lock ; Left/ Q? ; Up(Keystone+) ; Down(Keystone-)
10.2 LED Indicators 3 LEDS
10.2.1 Power On/Off Status Refer to LED definition
10.2.2 Lamp Status Refer to LED definition
10.2.3 Temperature Status Refer to LED definition
10.3 Electric Keystone Vertical keystone and adjustable range ±30° without digital zoom
or 3D function activate.(It will be updated in EVT0 stage)
10.4 Remote Control 5F.26J1K.291 x 1
11.0 Regulatory
Vendor: Refer to RFQ
11.1 Safety
Internal: Refer to B106 document
Vendor: Refer to RFQ
11.2 EMC
Internal: Refer to B106 document
11.3 ESD Follow IEC 61000-4-2 and EN55024 regulation
1.BenQ restriction of Hazardous Substance Guideline
11.4 GP (SUP-QM-07-02)
2.Other GP control items please refer PRR
12.0 Reliability
10
40000 hours except DMD chip, Color wheel, Lamp and Fan,
12.1 MTBF
Ballast
1). Lamp hour = [Hour used in Eco. Mode] + [Lamp life of Eco.
Mode]/[Lamp life of Normal Mode] *[Hour used in Normal
12.2 Lamp Lifetime
Mode]
2). 50% of Projectors will have 50% Initial Minimum Brightness
12.2.1 Normal Mode 4500 hrs
12.2.2 ECO Mode 6000 hrs
13.0 Other Feature
13.1 Color Temperature at Normal 5500/6500/7500/9300K
13.2 Digital Zoom PC: max 2X, Video: max 1.8X
13.3 Aspect Ratio Real / 4:3 / 16:9/ 16:10
13.4 Projection Methods Floor Front/Ceiling Front/Floor Rear/Ceiling Rear
13.5 3D Display Yes, support DLP 3D
13.6 LAN
13.6.1 LAN-Crestron eControl Yes
13.6.2 LAN-RoomView compatible Yes
13.6.3 LAN-PJ Link compatible Yes
13.6.4 LAN-AMX compatible Yes
13.6.5 LAN-Display(1 to many)
NA
(4 to 1)
13.7 Certificate
13.7.1 SRS Certificate No
13.7.2 Win7 Certificate Yes
Input / Output
Output Connectors
1.Input Terminals
1.1 Computer Input - 1 RGB DB-15 x 1 (Female Type)
1.2 Computer Input - 2 RGB DB-15x 1 (Female Type)
1.3 Video Composite Video (RCA X 1)
1.4 S-Video S-Video (Mini Din) X 1
1.5 Component - 1 RGB DB-15 x 1 (Female Type)
1.6 Component - 2 RGB DB-15 x 1 (Female Type)
1.7 DVI - 1 NA
1.8 DVI - 2 NA
1.9 HDMI Digital Video – 1 HDMI 1.3 x1 ( HDCP )
1.9.1 Support Audio Input YES
1.9.2 CEC control NA
1.10 HDMI Digital Video – 2 NA
1.10.1 Support Audio Input NA
1.10.2 CEC control NA
1.11 Audio Input – 1 (Mini Jack) Φ3.5mm Stereo Mini-Jack x 1
1.11.1 Related Source Computer -1 / Component -1 audio input
1.11.2 Input Signal Level 500mVrms 10 KΩ
1.12 Audio Input – 2 (Mini Jack) Φ3.5mm Stereo Mini-Jack x 1
1.12.1 Related Source Computer -2 / Component -2 audio input
1.12.2 Input Signal Level 500mVrms 10 KΩ
1.13 Audio Input – 3 (RCA R &L) RCA Audio Jack right and left
1.13.1 Related Source Video/S-Video audio input
1.14 USB Input NA
1.15 LAN Input NA
2.Output Terminals
2.1 Computer Output RGB DB-15 x 1 (Female Type)
2.1.1 Signal Source loop through Computer Input -1
11
2.2 Audio Output Φ3.5mm Mono Mini-Jack x 1
2.2.1 Signal Source Shared with all audio Input and Power on/off Ring Tone
2.3 Speaker 10W X 1
2.3.1 Amplifier 8W
3.Control Terminals and Interface
3.1 IR Receiver IR Receiver x2 (Front/Rear)
3.1.1 Angle ±30°
3.1.2 Distance 0~8m
3.2 USB
3.2.1 FW Upgrade Yes
3.2.2 Mouse Control Page up/down
3.2.3 USB Display No
3.3 RS-232 D-Sub 9 Pins x 1, male Type
3.3.1 FW Upgrade Yes
3.3.2 Control Command Yes
3.4 Lan Control RJ-45 x 1. Follow IEEE802.3u
3.5 12V Trigger (Screen Control) No
3.5.1 Driving Power No
3.5.2 Overload Protection No
3.6 Wired Remote Control No
Accessories
1.Accessory
1. Power Cord 1.8m X1
2. VGA Cable 1.8m X1
3. CD x 1 (22 Language) X1
4. Quick-Start_Card (18Language) X1
5. Remote Control 5F.26J1K.291 x 1
6. Carry Case N/A
7. Warranty Card By SKU
8. Adapter N/A
Environmental
1.Environmental
Operating 0~40°C, without condensation
1.1 Temperature
Storage -20~60°C, without condensation
Operating 10~90%RH, without condensation
1.2 Humidity
Storage 10~90%RH, without condensation
Without high altitude mode 0°C~35°C @
0~1499m above sea level
Operating
1.3 Altitude With high altitude mode 0°C~30°C @
1500~3000m above sea level
Storage 30℃@0~12,200m above sea level
12
Electrical Specification
1.1 Electrical Interface Character
1.1.1 Composite Video Input
(1) Pin definition (RCA Jack)
(2) Signal Level:

Signal Parameter Min Type Max
CVBS Amplitude, total (video+ sync) 1 Volts peak to peak
Luminance Amplitude, video 0.7 Volts peak to peak
Amplitude, sync 0.3 Volts peak to peak
Impedance 75 ohm
(3) Support Timings: (Version 01)
Horizontal Vertical Sub-carrier User Manual

Video mode frequency frequency Frequency Supported
(KHz) (Hz) (MHz)
NTSC* 15.73 60 3.58 Yes
PAL 15.63 50 4.43 Yes
SECAM 15.63 50 4.25 or 4.41 Yes
PAL-M 15.73 60 3.58 Yes
PAL-N 15.63 50 3.58 Yes
PAL-60 15.73 60 4.43 Yes
NTSC4.43 15.73 60 4.43 Yes
“*”It means the timing can support non-3D and 3D signal with field sequential format.
1.1.2 S-Video Input

(1) Pin definition (Mini Din)
4-pin Mini Din Connector

(2) Signal Level:
PIN Signal Parameter Min Type Max
1 GND
2 GND
3 CVBS Amplitude, total (video+ 1 Volts peak to peak
Luminance sync)
Amplitude, video 0.7 Volts peak to peak
Amplitude, sync 0.3 Volts peak to peak
Impedance 75 ohm
Amplitude (for NTSC) 286 m Volts peak to peak
CVBS Amplitude (for 300 m Volts peak to peak
4
Luminance PAL/SECAM)
Impedance 75 ohm
13
Horizontal Vertical Sub-carrier User Manual
Video mode frequency frequency Frequency Supported
(KHz) (Hz) (MHz)
NTSC* 15.73 60 3.58 Yes
PAL 15.63 50 4.43 Yes
SECAM 15.63 50 4.25 or 4.41 Yes
PAL-M 15.73 60 3.58 Yes
PAL-N 15.63 50 3.58 Yes
PAL-60 15.73 60 4.43 Yes
NTSC4.43 15.73 60 4.43 Yes
1.1.3 Component Video Input

(1) Pin definition { RGB DB-15 x 1 (Female Type) }
(2) Signal Level:

Pin Signal Parameter Min Type Max
1 Pr DATA Impedance 75 Ohm
3 Pb DATA Black pedestal 0 Volts
Y DATA_SOG Impedance 75 Ohm
Amplitude 1 Volts peak-to-peak
2 Video amplitude 0.7 Volts peak-to-peak
Sync amplitude 0.3 Volts peak-to-peak
Black pedestal 0 Volts
6 Red GND
7 Green GND
8 Blue GND

User
H-frequency
Resolution Mode Refresh rate (Hz) Clock (MHz) Manual
(kHz)
Supported
720 x 480* 480i 59.94 15.73 13.5 Yes
720 x 480 480p 59.94 31.47 27 Yes
720 x 576 576i 50 15.63 13.5 Yes
720 x 576 576p 50 31.25 27 Yes
1280 x 720 720/50p 50 37.5 74.25 Yes
1280 x 720 720/60p 60 45.00 74.25 Yes
1920 x 1080 1080/24P 24 27 74.25 Yes
1920 x 1080 1080/25P 25 28.13 74.25 Yes
1920 x 1080 1080/30P 30 33.75 74.25 Yes
1920 x 1080 1080/50i 50 28.13 74.25 Yes
1920 x 1080 1080/60i 60 33.75 74.25 Yes
1920 x 1080 1080/50P 50 56.25 148.5 Yes
1920 x 1080 1080/60P 60 67.5 148.5 Yes
14
1.1.4 HDMI/DVI Input
- HDMI 1.3 Compliance
- DVI 1.0 Compliance
- HDCP 1.1 Compliance
(1) Pin definition
Pin Signal
1 TMDS Data2+
2 TMDS Data2 Shield
3 TMDS Data2–
4 TMDS Data1+
5 TMDS Data1 Shield
6 TMDS Data1–
7 TMDS Data0+
8 TMDS Data0 Shield
9 TMDS Data0–
10 TMDS Clock+
11 TMDS Clock Shield
12 TMDS Clock–
13 CEC
14 Reserved (N.C. on device)
15 SCL
16 SDA
17 DDC/CEC Ground
18 +5 V Power (max 50 mA)
19 Hot Plug Detect
(2) Support Video Timings: (Version 01)

Vertical Dot Clock User Manual
Timing Resolution frequency H-frequency (kHz) Frequency Supported
(Hz) (MHz)
480i* 720(1440) x 480 59.94 15.73 27 Yes
480p 720 x 480 59.94 31.47 27 Yes
576i 720(1440) x 576 50 15.63 27 Yes
576p 720 x 576 50 31.25 27 Yes
720/50p 1280 x 720 50 37.5 74.25 Yes
720/60p 1280 x 720 60 45.00 74.25 Yes
1080/24P 1920 x 1080 24 27 74.25 Yes
1080/25P 1920 x 1080 25 28.13 74.25 Yes
1080/30P 1920 x 1080 30 33.75 74.25 Yes
1080/50i 1920 x 1080 50 28.13 74.25 Yes
1080/60i 1920 x 1080 60 33.75 74.25 Yes
1080/50P 1920 x 1080 50 56.25 148.5 Yes
1080/60P 1920 x 1080 60 67.5 148.5 Yes
15
(3) Support PC Timings: (Version 01)
Refresh rate User Manual
Resolution Mode H-frequency (kHz) Clock (MHz)
(Hz) Supported
VGA_60 59.940 31.469 25.175 Yes
VGA_72 72.809 37.861 31.500 Yes
640 x 480
VGA_75 75.000 37.500 31.500 Yes
VGA_85 85.008 43.269 36.000 Yes
720 x 400 720x400_70 70.087 31.469 28.3221 Yes
SVGA_60* 60.317 37.879 40.000 Yes
SVGA_72 72.188 48.077 50.000 Yes
SVGA_75 75.000 46.875 49.500 Yes
800 x 600
SVGA_85 85.061 53.674 56.250 Yes
SVGA_120** Yes
119.854 77.425 83.000
(Reduce Blanking)
XGA_60* 60.004 48.363 65.000 Yes
XGA_70 70.069 56.476 75.000 Yes
XGA_75 75.029 60.023 78.750 Yes
1024 x 768
XGA_85 84.997 68.667 94.500 Yes
XGA_120** Yes
119.989 97.551 115.500
(Reduce Blanking)
1152 x 864 1152 x 864_75 75.00 67.500 108.000 Yes
1024x576 BenQ Notebook Timing 60.00 35.820 46.996 Yes
1024x600 BenQ Notebook Timing 64.995 41.467 51.419 Yes
1280 x 768_60* No
60 47.396 68.25
1280 x 768 (Reduce Blanking)
1280 x 768_60* 59.870 47.776 79.5 Yes
WXGA_60* 59.810 49.702 83.500 Yes
WXGA_75 74.934 62.795 106.500 Yes
1280 x 800 WXGA_85 84.880 71.554 122.500 Yes
WXGA_120** Yes
119.909 101.563 146.25
(Reduce Blanking)
SXGA_60*** 60.020 63.981 108.000 Yes
1280 x 1024 SXGA_75 75.025 79.976 135.000 Yes
SXGA_85 85.024 91.146 157.500 Yes
1280 x 960_60*** 60.000 60.000 108 Yes
1280 x 960
1280 x 960_85 85.002 85.938 148.500 Yes
1360 x 768 1360 x 768_60*** 60.015 47.712 85.500 Yes
WXGA+_60*** No
60 55.469 88.75
WXGA+_60*** 59.887 55.935 106.500 Yes
1400X1050 SXGA+_60*** 59.978 65.317 121.750 Yes
1600x1200 UXGA 60.000 75.000 162.000 Yes
1680x1050_60 No
59.883 64.674 119.000
1680x1050 (Reduce Blanking)
1680x1050_60 59.954 65.290 146.250 Yes
1920x1200_60 No
1920 x 1200 59.950 74.038 154.000
(Reduce Blanking)
640x480@67Hz MAC13 66.667 35.000 30.240 Yes
832x624@75Hz MAC16 74.546 49.722 57.280 Yes
1024x768@75Hz MAC19 75.020 60.241 80.000 Yes
1152x870@75Hz MAC21 75.06 68.68 100.00 Yes
“*” It means the timing can support non-3D and 3D signal with frame sequential and over-under
format.
“**”It means the timing can support non-3D and 3D signal with frame sequential format.
“***”It means the timing can support non-3D and 3D signal with over-under format.
There 3D timing showing depend the EDID file and VGA display card. It is possible that user cannot
16
choose the above 3D timings on VGA display card.
(4) Support Audio:

(a) HDMI Mode:
- Support LPCM, two audio channels
- Support audio sampling rate : 32kHz, 44.1kHz, 48kHz
- Support audio bit rate : 16 bits, 20 bits, 24 bits
(b) DVI Mode:
Analog audio is supported through PC audio input terminal.
1.1.5 PC Input
(1) Pin definition and Signal Level:
Pin Signal Parameter Min Type Max

1 RDATA Impedance 75 Ohm
2 GDATA Amplitude 0.7 Volts peak-to-peak
3 BDATA Black pedestal 0 Volts
Pixel Clock 170 M Hz
GDATA_SOG Impedance 75 Ohm
Amplitude 1 Volts peak-to-peak
Video amplitude 0.7 Volts peak-to-peak
2
Sync amplitude 0.3 Volts peak-to-peak
Black pedestal 0 Volts
Pixel Clock 170 M Hz
HDATA Impedance 1 K ohm
Amplitude, low level 0 0.5 volt
13
Amplitude, high level 2.5 5 Volt
Frequency 31 102 K Hz
VDATA Impedance 1 K ohm
Amplitude, low level 0 0.8 volt
14
Frequency 48 120 Hz
SDADATA Amplitude, low level 0 0.8 volt
12
SCLDATA Amplitude, low level 0 0.8 volt
15
4 NC
5 NC
6 Red GND
7 Green GND
8 Blue GND
9 DDCP 5V 5 Volts
10 Sync. Return
11 GND
G DATA Amplitude (with sync) 1 Volts peak to peak
2
Share with Y Impedance 75 ohm
R DATA Amplitude 0.7 Volts peak to peak
1
Share with Pr Impedance 75 ohm
B DATA Amplitude 0.7 Volts peak to peak
3
Share with Pb Impedance 75 ohm
17
(2) Support PC Timings: (Version 01)
H-frequency User Manual
Resolution Mode Refresh rate (Hz) Clock (MHz)
(kHz) Supported
720 x 400 720x400_70 70.087 31.469 28.3221 Yes
VGA_60 59.940 31.469 25.175 Yes
VGA_72 72.809 37.861 31.500 Yes
640 x 480
VGA_75 75.000 37.500 31.500 Yes
VGA_85 85.008 43.269 36.000 Yes
SVGA_56 56.250 35.156 36.000 Yes
SVGA_60* 60.317 37.879 40.000 Yes
SVGA_72 72.188 48.077 50.000 Yes
800 x 600 SVGA_75 75.000 46.875 49.500 Yes
SVGA_85 85.061 53.674 56.250 Yes
SVGA_120** Yes
119.854 77.425 83.000
(Reduce Blanking)
XGA_60* 60.004 48.363 65.000 Yes
XGA_70 70.069 56.476 75.000 Yes
XGA_75 75.029 60.023 78.750 Yes
1024 x 768
XGA_85 84.997 68.667 94.500 Yes
XGA_120** Yes
119.989 97.551 115.500
(Reduce Blanking)
1152 x 864 1152 x 864_75 75.00 67.500 108.000 Yes
1024 x 576 BenQ Notebook Timing 60.0 35.820 46.966 Yes
1024 x 600 BenQ Notebook Timing 64.995 41.467 51.419 Yes
1280 x 768_60* No
60 47.396 68.25
1280 x 768_60* 59.870 47.776 79.5 Yes
WXGA_60* 59.810 49.702 83.500 Yes
WXGA_75 74.934 62.795 106.500 Yes
1280 x 800 WXGA_85 84.880 71.554 122.500 Yes
WXGA_120** Yes
119.909 101.563 146.25
(Reduce Blanking)
SXGA_60*** 60.020 63.981 108.000 Yes
1280 x 1024 SXGA_75 75.025 79.976 135.000 Yes
SXGA_85 85.024 91.146 157.500 Yes
1280 x 960_60*** 60.000 60.000 108 Yes
1280 x 960
1280 x 960_85 85.002 85.938 148.500 Yes
1360 x 768 1360 x 768_60*** 60.015 47.712 85.500 Yes
WXGA+_60*** No
60 55.469 88.75
WXGA+_60*** 59.887 55.935 106.500 Yes
1400X1050 SXGA+_60*** 59.978 65.317 121.750 Yes
1600x1200 UXGA 60.000 75.000 162.000 Yes
1680x1050_60 No
59.883 64.674 119.000
1680x1050_60 59.954 65.290 146.250 Yes
640x480@67Hz MAC13 66.667 35.000 30.240 Yes
832x624@75Hz MAC16 74.546 49.722 57.280 Yes
1024x768@75Hz MAC19 74.93 60.241 80.000 Yes
1152x870@75Hz MAC21 75.06 68.68 100.00 Yes
“*” It means the timing can support non-3D and 3D signal with frame sequential and over-under
format.
“**”It means the timing can support non-3D and 3D signal with frame sequential format.
“***”It means the timing can support non-3D and 3D signal with over-under format.
There 3D timing showing depend the EDID file and VGA display card. It is possible that user cannot
choose the above 3D timings on VGA display card.
18
1.1.6 Audio Input (RCAx2)
(1) Pin definition :
(2) Signal Level: N/A

1 L Audio Amplitude 0.5 2 VRMS
Impedance 10 KΩ
Amplitude 0.5 2 VRMS
2 R Audio Impedance 10 KΩ
1.1.7 Audio Input (Mini-Jack φ3.5mm)

(1) Pin definition
(2) Signal Level:

1 GND
2 Audio In Left Amplitude 0.5 2 VRMS
Impedance 10 KΩ
3 NC
4 NC
Audio In Right Amplitude 0.5 2 VRMS
5 Impedance 10 KΩ
22 Audio In Left Amplitude 0.5 2 VRMS
Impedance 10 KΩ
23 NC
24 NC
Audio In Right Amplitude 0.5 2 VRMS
25 Impedance 10 KΩ
1.1.8 Audio Headphone Output (Phone-Jack φ3.5mm)

(1) Pin definition
19
(2) Signal Level:
32 Audio Out Left Amplitude mV
Impedance 32 Ω
33 NC
Audio out Output ON 0.2 VDD
34
detect Output Off 0.8 VDD
Audio Out Left Amplitude mV
35
Impedance 32 Ω
1.1.9 RS232 Control Port

(1) Pin definition (D-Sub 9 Pin)
(2) Signal Level:

1 NC
2 RX Amplitude (with sync) -25 25 Volt
3 TX Amplitude -13.2 13.2 Volt
4 NC
5 GND
6 NC
7 RTSZ
8 CTSZ
9 NC
20
1.1.10 Lan Control Port (Follow IEEE 802.3)
(1) Pin definition(speed:10M/100M)
(2) Signal Level:
PIN Signal
1 TD+
2 TD-
3 RD+
4 Common Mode Termination
6 RD-
1.2 Speaker
Signal Parameter Min Type Max
Audio Impedance (audio in) 10 Kohm
Amplitude (audio in) 500 mVolts rms
Bandwidth 300Hz 16kHz
S/N Ratio 40 dB
Total Harmonic Distortion 10 %
Power Supply Specification

1.1 Input Power Specification
Specification Description
Input Voltage Range The unit shall meet all the operating requirements with the range 90
~ 264 VAC
Frequency Range The unit shall meet all the operating requirements with an input
frequency range 47 Hz ~ 63 Hz
Regulation Efficiency 80 % (typical) measuring at 115Vac and full load
3.2 Varist Requirement

The power supply’s varist component should stand 510V or higher power.
3.3 Lamp Power Requirement
Specification Description
Starting pulse from Ignitor 2.1KV Min.
21
UI Specification
Keypad Description
ID Key Name Detailed Description

Key 0 Power Use this button to turn your Data Projector on and off (standby mode).
Key 9 Source To select input sources as Computer, Video, S-Video, YPbPr
Key 7 Auto Toggle auto-tracking image function
Key 3 Blank Press “Blank” key first to blank the screen
Key 5 Mode/Enter (1) When there is no OSD menu, this bottom is Mode hot key; user would
press this bottom to choose one of preset modes
(2) When there is confirm message, user could press this key to confirm
Key 1 Menu/Exit Press this key to open/exit the OSD menu
Key 8 Right/ (1). When there is OSD menu, user can press this key to move to right item
(2). By pressing “Volume +” button, the volume of the magnified sound will
be increase gradually.
Key 2 Left/ (1). When there is OSD menu, user can press this key to move to the left item.
(2). By pressing “Volume -” button, the volume of the magnified sound will be
reduced gradually.
Key 4 Up (1) Move item bar. (2) Move to page level. (3) Keystone+.
Key 6 Down (1) Move item bar. (2) Move to page level. (3) Keystone-.
22
Remote Control Function and Key Code Definition
(Detail See Appendix2)
23
3.2 Packing
【NOTE】The updated Service BOM is on SPO system. Please check it to order service parts.
1. For 14
14A~14
A~14T, Exclude 14D
14D/1
4D/14
/14F/14L
/14L :
Accessory
(Manual, CD, R/C…etc.)
Power Cord
After put in Power cord & Warranty

card -> Seal the hole by tape ->
Stick CTN label
24
2. For 14
14L :
Accessory

Stick CTN label
25
3. For 14D
14D/1
4D/14F
/14F :
Accessory

Stick CTN label
26
CTN LBL PRINTING:
1. For 9H.J4S77
9H.J4S77.1
4S77.14
.14A/L
27
2. For 9H.J4S77
9H.J4S77.1
4S77.14
.14J/K
3. For 9H.J4S77
9H.J4S77.1
4S77.14
.14E/U
28
4. For 9H.J4S77
9H.J4S77.1
4S77.14
.14D/14
D/14F
5. For 9H.J4S77
9H.J4S77.1
4S77.14
.14P/S
29
6. For 9H.J4S77
9H.J4S77.1
4S77.14
.14T
7. For 9H.J4S77
9H.J4S77.13C
4S77.13C
30
SPEC LBL PRINTING:
1. For 9H.J4S77
9H.J4S77.1
4S77.14
.14A~U(Exclude 14
14C)
31
2. For 9H.J4S77
9H.J4S77.1
4S77.14
.14C
32
LAMP LBL PRINTING
33
3.3
3.3 Customer Acceptance
1.0 SCOPE
This document establishes the general workmanship standards and functional
acceptance criteria for projector produced by BENQ.
2.0 PURPOSE
The purpose of this publication is to define a procedure for inspection of the
projector by means of a customer acceptance test, the method of evaluation of
defects and rules for specifying acceptance levels.
3.0 APPLICATION
The "Customer Acceptance Criteria" is applicable to the inspection of the projector,

completely packed and ready for dispatch to customers. Unless otherwise specified,
the customer acceptance inspection should be conducted at manufacturer's site.
4.0 DEFINITION
The "Customer Acceptance Criteria" is the document defining the process of

examining, testing or otherwise comparing the product with a given set of specified
technical, esthetic and workmanship requirements leading to an evaluation of the
"degree of fitness for use", including possible personal injury or property damage for
the use of the product.
5.0 CLASSIFICATION OF DEFECTS
The defects are grouped into the following classes:

5.1 Critical defect
A critical defect is a defect which judgment and experience indicate that there is
likely to result in hazardous or unsafe conditions for individuals using product.
5.2 Major defect
A major defect is a defect, other than critical one, is likely to result in failure, or
to reduce materially the usability of the product for its intended purpose.
5.3 Minor defect
34
A minor defect is a defect that is not likely to reduce materially the usability of its
intended purpose, or is a departure from established standards having little
bearing on the effective use of operation of the product.
Note: If BenQ defect undefined failure, and it judged that is reduce the merchandisebility, BenQ
CM Inform this defect. After that parties make communication and decide how to solve.
6.0 EXPRESSION OF DEFECTIVES

Number of defects
Percent of defects = ------------------------------------------ X 100%
Number of products inspected
7.0 INSPECTION STANDARD

Unless otherwise specified, the inspection standard will be defined by MIL-STD-105E,
NORMAL INSPECTION LEVEL Ⅱ, SINGLE SAMPLING PLAN.
7.1 Acceptance Quality Level
7.1.1 Critical Defect:

When a critical defect is found, this must be reported immediately upon
detection, the lot or batch shall be rejected and further shipments shall be
held up pending instructions from the responsible person in relevant
department.
7.1.2 under normal sampling
Critical Defective : 0% AQL

Major Defective : 0.65% AQL
Minor Defective : 2.5% AQL
8.0 GENERAL RULES
8.1 The inspection must be carried out by trained inspectors who have good knowledge about
the product.
8.2 The inspection must be based upon the documents concerning the completely assembled
and packed product.
35
8.3 When more defects appear with the same unit only the most serious defect has to be taken
into account.
8.4 Defects found in accessory packed with the product such as Cable, Connector, Manual, CD
and the like, and being inspected as a part of the complete product, must be included in the
evaluation.
8.5 The evaluation must be within the limits of the product specification and, for not specified
characteristics, refer to the sample machine or the judgment of BENQ QA Engineer. But any
kind of proposals or judgments must be reasonable and acceptable by both sides.
8.6 Faults must be able to be repeatedly demonstrated.
9.0 TEST CONDITIONS
Unless other prescription, the test conditions are as followings:

Nominal voltage: refer to operation manual
Environmental illumination:
Variable from 500 to 800 Lux (For appearance inspection)
Variable from 0 to 7 Lux (For functional inspection)
Temperature: 25±5℃
Visual inspection shall be done with the distance from eyes to the sample 40~50
cm.
Display mode: refer to operation manual
10.0 TEST EQUIPMENTS

Dark room
PC
Pattern Generator: Chroma or equivalent
DVD player
Power supply (100~240 VAC) with consumption meter
Measuring tape
36
4. Level 1 Cosmetic / Appearance / Alignment Service
4.1 Cosmetic / Appearance Inspection Criteria
TABLE 1. General Product of plastic outlook of dot, blemish, and others spec inspection standard (产
品一般外观塑料件的黑点、杂质、凸点、砂粒缺陷检验标准)
A 级面 B 级面 C 级面
规格 A surface B surface C surface
Spec (允许数) (允许数) (允许数)
(面积 cm2) (Number of defect) (Number of defect) (Number of defect)
( Area cm2 ) 100*10 100*1 100*1
20*20 50*50 70*70 20*20 50*50 70*70 20*20 50*50 70*70
0 00 00
2
P < 0.1 mm 不计不计不计不计不计不计不计不计不计
杂质点距 Distance
不计不计不计
Ignor Ignor Ignor Ignor Ignor Ignor Ignor Ignor Ignor
Ignore Ignore Ignore
Particle 2cm e e e e e e e e e
2
黑点 0.1△P< 0.2 mm
Blemish 点距 Distance 2 3 4 5 2 3 4 5 4 4 5 6
| 4cm
2
异色点 0.2△P <0.3mm
点距 Distance
0 0 0 0 2 3 4 5 3 4 5 6
4cm
P<0.1 mm2 不计不计不计不计不计不计不计不计不计
点距 Distance
不计不计不计
凸点 Ignor Ignor Ignor Ignor Ignor Ignor Ignor Ignor Ignor
Ignore Ignore Ignore
砂粒 2cm e e e e e e e e e
2
棉絮 0.1△P<0.2mm
点距 Distance 4 4 5 6 5 5 6 7 6 6 7 8
毛屑
Particle 4cm
| 0.2△P < 0.3mm2
同色点点距 Distance 3 4 4 5 4 5 5 6 6 7 7 8
Spot 4cm
with 0.3△P < 0.5mm2
same 点距 Distance 2 2 3 4 3 3 4 5 4 4 5 6
color 5cm
Total 4 4 5 6 5 5 6 7 6 6 7 8
备注 Note:
1. 检测面积 A <20*20 以 20*20 之规范检验之, 20*20≦A<50*50，以 50*50 等级检验之，以此类推.
Use the 20*20 criteria to the area less than 20*20; 50*50 inspection criteria to the area 20*20≦A<50*50;
etc.
杂质/黑点/异色点(Particle/Blemish/Color Spot)
1.1 A、B、C 级面定义请参考 6.2 级面定义。
Definition of surface A, B, C refer to 6.2
1.2 LOGO 周边 2 cm 内不可有 0.05 mm 以上之点, (0.05 mm 以内之点不计)。
2 2
2
Blemish around the logo must be equal or smaller than 0.05 mm
1.3 表面气泡—不可有。
Bubble on the surface is to be reject.
37
TABLE 2 :产品一般外观的塑料件检验标准(General Product of plastic outlook inspection
standard)
NO Appearance Spec
1 缩水 A 区: 不可有缩水, 以带手套检验, 手摸过去不可有凹
Shrinkage 陷的感觉
A region: No Shrink. With gloves, no feeling of sink when touching the
surface
B / C 区: 不能明显看出
B/C region: not obvious
2 流痕, 咬花, 光泽不能有明显的深浅不均
Run, Texture, Gloss No obvious non-uniformity
3 接合线用指甲划过不会有停顿感,并附近无明显之光泽差异
Welding Line/Knit Line When scratching on it, there’s no feeling of obstruction. Also, there
should not be obvious difference in gloss nearby it.
4 顶白不可
Ejector Mark Reject
5 Label/screws shortage 不允许
Reject
6 缺料缺料不可影响机构强度和表面
Material shortage Material shortage is not allowed to impact structure strength and
surface
7 色差喷漆(Painting): ΔE<=2; L<=1.5 ; Δ A,B <= 0.6
Chromatic aberration 银粉漆 (Paint, aluminum).
ΔE<=2 L<=1.0; Δ A, B <= 0.6
非银粉漆(Paint, non-aluminum)
素材(Raw material) : ΔL,A,B<=0.6 ,ΔE<=0.75
8 印刷文字印刷不得有漏印、断线、重影、组细不均、溢墨、印偏( 1mm )、
Printing 印斜 (歪斜＜0.3 mm )。
Printing must not have incomplete printing, break off, overlap,
uneven thickness, excessive ink, printing misalignment
(1mm), printing slanting & crooked (<0.3mm)
文字印刷颜色须确认是否正确。
Printing color must be comparable to color chip and sample.
9 Logo of panel sticker 文字印刷不得有漏印.断线.重影.组细不均.溢墨.印偏( 1mm)印斜
(歪斜＜ 0.5 mm).
Printing must not have incomplete printing, break off, overlap, uneven
thickness, excessive ink, printing misalignment (1mm), printing
slanting & crooked (<0.5mm)
文字印刷颜色须确认是否正确.
Printing color must be comparable to color chip and sample.
10 刮伤 Side A:
Scratch/Nicks (W < 0.1mm , L < 3mm): 容许 1 个
Only 1 this kind of scratch is accepted
W < 0.1mm , L < 3-5mm 容许 0 个
No this kind of scratch is accepted
Side B:
W < 0.15mm , L < 3mm 容许 2 个
Only less than 2 this kind of scratch is accepted
W < 0.15mm , L < 3-5mm 容许 1 个
Side C:
38
W < 0.2mm , L < 1mm 容许 4 个
W < 0.2mm , L < 3mm 容许 3 个
W < 0.2mm , L < 3-5mm 容许 2 个
Note:
刮伤见底材者不允许
Severe scratch which disclose the Natural
1. 刮擦伤两两需相距 5cm 以上
Each scratch should be 5cm more far away from each other
TABLE 3 产品镁铝合金制品之黑点、杂质、凸点、砂粒缺陷检验标准检验规范
(Magnesium-Aluminum Alloy Products that Dot, Blemish, and Others spec.)
A 级面 B 级面 C 级面
规格 A surface B surface C surface
Spec (允许数) (允许数) (允许数)
(面积 cm2) (Number of defect) (Number of defect) (Number of defect)
( Area cm2 ) 100*10 100*1 100*10
20*20 50*50 70*70 20*20 50*50 70*70 20*20 50*50 70*70
0 00 0
不计不计不计不计不计不计不计不计不计不计
杂质 P < 0.1 mm2 Ignor Ignor Ignor
不计
Ignor Ignor Ignor Ignor Ignor Ignor Ignor
不计
Ignore Ignore
Particl e e e e e e e e e e
e 0.1△P< 0.3 mm2
黑点点距 7.5cm 1 2 3 4 2 3 3 5 3 4 5 6
Blemis Distance
h 0.3△P <0.5mm2
| 点距 7.5cm 0 0 0 0 2 2 3 4 2 3 4 5
异色 Distance
点 0.5△P <0.7mm2
Color 点距 7.5cm 0 0 0 0 0 0 1 2 1 2 3 4
spot Distance
凸点 P<0.1 mm2 不计不计不计不计不计不计不计不计不计不计
点距 7.5cm
不计不计
Ignor Ignor Ignor Ignor Ignor Ignor Ignor Ignor Ignor Ignor
砂粒 Ignore Ignore
棉絮 Distance e e e e e e e e e e
2
0.1△P<0.3mm
毛屑
点距 7.5cm 2 2 3 4 3 4 5 6 4 5 6 7
Particl
e Distance
| 0.3△P < 0.5mm2
同色点距 7.5cm 1 1 2 3 2 2 3 4 2 3 3 4
Distance
点
Spot 0.5△P < 0.7mm2
with 点距 7.5cm 0 0 1 2 1 1 2 3 1 2 2 3
same Distance
color
Total 3 3 4 5 5 6 7 8 6 7 8 9
39
4.2 OPERATIONAL INSPECTION CRITERIA
1. TEST PATTERN
PATTERN PATTERN TEST ITEM
ANSI Brightness、Bright Uniformity、FOFO

Full white
Contrast Ratio、CIE white coordinate、Throw
Ratio、Zoom Ratio、Distortion
Full Dark
FOFO Contrast Ratio
Full Red Impurity、CIE coordinate
Full Green Impurity、CIE coordinate
Full Blue Impurity、CIE coordinate
Chromo
Focus Range
Pattern84
General-1
Performance/ Timing check/ function check
pattern
32 Gray Gray Check
Check the DDC information,

DDC check Including S/N, model, manufacturer name,
product code.
40
2. TEST CONTENT:
Test Condition TEST ITEM Input Equipment
Chroma pattern Focus/ Focus range
PC Mode FULL W , R , G , B Impurity, CIE coordinate, D-SUB Chroma
pixel fail
HDTV NTSC Picture performance YPbPr Chroma / BS
Tuner
DVD NTSC disk/ PAL disk Picture quality Video
picture S-video DVD player
3. SPECIFICATION:
SPECIFICATION:
Item Spec. Condition Pattern
Contrast: Preset
ANSI Brightness Minimum 2000Lumens Full white
Brightness: Preset
Contrast: Preset
Bright Uniformity Minimum 45% Full white
Brightness: Preset
Contrast: Preset
ANSI Contrast Minimum 150:1 Chessboard
Brightness: Preset
Minimum 2400:1(w/ Contrast: Preset
FOFO Contrast Ratio Full white and Full dark
WCE) Brightness: Preset
△△0.5 lux compared
Light Leakage with center point @ full Contrast: Preset
Full dark
(In Active Area) black pattern within 78” Brightness: Preset
(Diagonal at 0.485m).
≦0.5 lux, @ full black
Light Leakage pattern with Contrast: Preset
78”~90“(Diagonal at Full dark
(Out of Active Area) Brightness: Preset
0.485m)
(Except DMD Defect)
x=0.315+0.04 Contrast: Preset
CIE white coordinate Full white
y=0.364+0.04 Brightness: Preset
CIE red coordinate Full Red
CIE green coordinate Full Green
CIE blue coordinate Full Blue
Contrast: Preset
Throw Ratio 0.49 (95"±3%@ 1m) Brightness: Preset
Full white
(W2-W1) / (W1+W2) Contrast: Preset
Keystone Distortion Full white
<1.0% Brightness: Preset
(H1+H2-2×H3)/2H2 Contrast: Preset
Vertical TV Distortion Full white
<1.0% Brightness: Preset
Pixel clear and uniform at Contrast: Preset
Clearly Focus Range Chroma 84 X pattern
0.75~1.6m Brightness: Preset
Brightness: Preset
Gray Check Should be clear and bright Chromo 32 gray pattern
Contrast: Preset
See See See Defect
DMD Image Quality Defect Classification
Defect Classification Classification
640X480 800x600, Contrast: Preset
PC
Brightness: Preset
General-1 pattern
compressed 1600x1200;
NTSC/NTSC4.43/PAL(Incl
Contrast: Preset
Video uding PAL-M, PAL-N)
Brightness: Preset
Color-bar pattern
/SECAM/PAL60
NTSC (480i)/ 480p/ PAL
YPbPr Contrast: Preset
(576i)/576p, HDTV
Brightness: Preset
Color-bar pattern
(720P/1080i/p)
41
4. Power Consumption:
Max. 335W
1W Max. at 100 ~ 240VAC
Standby
8.2 Power consumption (disable loop through, LAN control, audio out)
Normal Typical 300W@110Vac
ECO Typical 239W@110Vac
5. OPERATIONAL
OPERATIONAL INSPECTION CRITERIA:
No Description Class
1 Noise
1.1 When power on or power off, fan or color wheel get abnormal noise. Major
1.2 When normal operation, noise exceed noise level (refer to Q201 document) Major
2 Display Quality (include input: Video, S-video, YPbPr, HDMI, and D-sub
or RGB)
2.1 Focus range out of specification Major
2.2 Focus fail (focus not clear or flare/ defocus/ lateral color out of Major
specification)
2.3 Brightness & Uniformity --- out of specification. Major
2.4 Contrast ratio --- out of specification Major
2.5 Color coordinates --- out of specification. Major
2.6 Light leakage out of specification (active area or out of active area) Major
2.7 Throw ratio out of specification Major
2.8 Room ratio out of specification Major
2.9 Picture distortion out of specification Major
2.10 DMD image out of specification Major
2.11 Picture dust or other image quality out of specification Major
2.12 Gray stage check --- Missing stage Major
2.13 Video noise --- If video noise presented Major
2.14 DDC data error / incorrect Major
2.15 Mode detection error Major
2.16 OSD Malfunction Major
3 Audio Quality
3.1 Audio malfunction Major
3.2 Speaker no function Major
3.4 Volume mute malfunction Major
4 Remote control malfunction
malfunction Major
42
6. IMAGE QUALITY SPECIFICATION:
SEQ# Test SCREEN ACCEPTANCE CRITERIA
Major Dark ≦4 visible dark blemishes are allowed in the active area
1 Blue 60
Blemish No blemish will be ＞1.5” long/diameter
Major Light ≦4 visible dark blemishes are allowed in the active area
2 Gray 10
Blemish No blemish will be ＞1.5” long/diameter
Reset Boundary
3 Gray 30 No reset boundary artifacts allowed
Artifact
Eyecatchers /
4 Any screen Eyecatcher and border artifacts are allowed
Border Artifacts
No adjacent pixels
Any screen No bright pixels in Active Area
Gray 10 No unstable Pixels in Active Area
Any screen ≦ 1 right pixel in the POM
5 Projected Images Gray 10
Whit ≦ 4 dark pixels in the Active Area
Any screen No DMD window aperture shadowing on the Active
Any screen Area
Minor blemishes are allowed
43
4.3 Software/Firmware Upgrade Process
A. Basic Operating
(a) Standby Mode：
Mode：
User can just plug in power cord, then projector will enter standby mode. Power LED will show
Red for around 1 sec, then show Orange continuously as the figure shown below. When the power
LED shows Red, it means system is not ready for standby. In another word, if the power LED shows
Orange, it means system is in standby mode and the DLP system has no power support, except
MCU and its related circuits.
When standby mode, system power consumption will be less than 1 Watt.
User can turn on projector after plugging in power cord whatever the power led is red or orange.
Standby Mode
(b) Download Mode：

Mode：
This mode is applied for firmware download.
If operator wants to enter this mode, he should press and hold both keypad-POWER
POWER and
Keypad-AUTO
AUTO at the same time, then plug in power cord. Power LED will show Green for around
1 sec, then show Red continuously as the figure shown below. In download mode, system will be
supported by full power but will not turn on projector. Operator can use DLP composer to
download new firmware.
Download Mode
44
(c) Power On：
On：
User can press Keypad Power to turn on projector. User can also use IR remote controller and
RS-232 Command：<CR>*pow=on#<CR> to do this action. When system turning on, power LED
will flash Green as the figure shown below.
Power On
(d) Power Off：

Off：
If user wants to turn off projector, user can double click keypad Power, use IR remote controller,
or RS-232 Command：<CR>*pow=off#<CR>. Then, system will cool itself via fans for 3 seconds
(quick cooling) or 90 seconds (normal). During cooling, Power LED will flash Orange. After
cooling, system will return to standby mode and Power LED will become Orange as the figure
shown below.
Power Off
B. Download MCU Code and Firmware

(a) Auto MCU Code Download：
Download：(for Low-
Low-Power Standby)
Condition：
Condition：
Auto Detect, download by MCU itself.
Situation 1：MCU code is empty (The 1st time to plug in power cord)
Situation 2：MCU version update
45
System Action：
Action：
System needs around 2 sec to download MCU itself automatically.
Downloading：
Downloading：Power LED will show Red and Lamp LED will show Green.
Download Fail：
Fail：Power LED will show Orange and Lamp LED will show Red.
Download Success：
Success：System will go back standby mode and Power LED will show Orange.
Notice：
Notice：
Do NOT interrupt power when downloading.
(b) Download
Download Firmware
i. DLP Composer lite install procedure
(1) Installation
1. Double click the Setup file for DLP Composer Lite (use 9.2 or above version) to start to install
program.
2. When the Installation Wizard appears, click “Next”.
3. Select to accept the License Agreement, than click “Next”
46
4. Click “Next” in the following steps to continue installation process.
Note:
The default installation directory is:
C:\
C:\Program Files\
Files\DLP Composer Lite9.2
If you want to install to a different directory (perhaps
alongside a prior release of DLP Composer™ Lite), click
the "Browse" button on the "Select Features" page.
5. When finishing installation, click “Finish”, and then restart your computer to complete the
installation process.
47
(2) Setting for your first use
Select Library:
1. Make sure the correct library file exist in your assigned path. If not, unzip the library from the
installation file (“DDP243x_Download_Tool_Ver1.3.zip”, or later version), and save it into your
assigned path.
2. When start to use this program to download at first time, you need to assign correct Library path
in DLP Composer Lite program.
Select “Edit”->”Preference”.
Click “Browse”
Browse” to assign
path for library files
48
Click the library
folder to assign
the path.
Then Click “OK”

OK”.
Click “OK”
OK”.
Set communication (for download by RS232):

1. Select “Edit”->”Preference”.
2. Select “Communications”-> “Serial Port” -> ”Config”.
49
3. Make sure the settings are the same as below figure-> Click ”OK”.
4. Click ”OK”.
ii. Download Procedure

How to download
Hardware required
1. Standard RS232 Download cable (SPEC as below)
D-sub 9-pin Female for Both terminals
50
Personal computer or laptop computer
Software required
1. DLP Composer Lite program
2. New version FW
Download procedure
1. Connect RS-232 cable to PC and projector
2. Let projector be in Download Mode:

Mode:
- Press and hold keypad-POWER
POWER and AUTO at the same time, then plug in power cord.
- Power LED will show Green for around 1 sec, then show Red continuously.
3. Execute DLP Composer Lite 9.2 program
4. To select the RS-232 communications interface, choose "Preferences" from the "Edit" menu,
click the "Communications" page and choose "Serial Port".
51
5. Click on “Flash Loader” and browse the image file (new version firmware)
6. Select Complete Image Download, and make sure to check “Skip Boot loader area (32KB)”
7. Press “Reset Bus” and check the status which should show “Bus Reset”
52
8. Press “Start Download” to begin update new firmware.
9. Press “Yes” to continue.
10. Wait till Download complete.
11. When download complete, LED signal on projector will show standby status (orange light
continuously).
53
4.4 Method to enter factory menu
1. Press Menu/EXIT on keypad than the main menu popup
2. When showing main menu, press Source + Mode/ENTER at the same time
3. Factory menu popup at the top-left of display
54
4.5 RS-
RS-232 connection
1. Below shows the illustration of connection between PC and Projector.
<CAUTION>
Make sure that your computer and projector are turned off before connection.
Power on the computer first, and then plug the power cord of the projector.
(It may cause Com port incorrect function, if you do not follow this instruction)
Adapters may be necessary depending on the PC connected to this projector. Please contact with
your dealer for further details.
2. Hardware connection
<Download cable 1>
WIRE ARRANGEMENT
P1 COLOR P2
1 BLACK 1
2 BROWN 3
3 RED 2
4 ORANGE 4
5 YELLOW 5
6 GREEN 6
7 BLUE 8
8 PURPLE 7
9 GRAY 9
CASE DRAIN WIRE CASE
<pin assignment for this two end>

Pin Description Pin Description
1 NC 2 RXD 1 2 3 4 5
3 TXD 4 NC
5 GND 6 NC 6 7 8 9
7 RTS 8 CTS
9 NC
55
Interface Settings
RS-232 protocol
Baud Rate 115200 bps (default)
Changeable settings in User OSD
(2400/4800/9600/14400/19200/38400/57600/115200)
Data Length 8 bit
Parity Check None
Stop Bit 1 bit
Flow Control None
Software specification
1. When input cmd fail, e.g. correct input is “*pow=?#” but input “*po=?#”, or input “*mute=on#”
while projector is already mute, it will show “*Illegal format#”.
2. When input cmd but projector has no such function item, e.g. input “*sour=RGB2#” but
projector has no RGB2 connector, it will show “*Unsupported item#”.
3. When cmd and function are both workable, but it’s not under the status which cmd can be
executed, e.g. input “*asp=4:3#” while not connecting source, it will show “*Block item#”.
4. When input “query” cmd (with “?”), e.g. input “*sour=?#”, it will echo the same input strings
with some value.
5. Press “Enter” key after” ＞”, it should be no echo and skip to the next row.
6. Press “Space” and “Enter” key after” ＞”, it will echo”*Illegal format#”
Command Category
Refer to Appendix 2
56
4.6 Adjustment / Alignment Procedure
Content
1. Color Wheel Delay Alignment
2. Overfill adjustment
3. PC Alignment Procedure
57
1. Color Wheel Delay Alignment
Procedure:
1. Enter Factory Mode
2. Enter Block 1
3. Change CW Delay by adjusting the following gray pattern to smooth
32 Gray pattern
58
2. Overfill adjustment
1. “Full White Pattern” is suggested for this alignment.
2. Adjust 2 LP-alignment Screws (upper side / lower front side of Optical Engine) behind Color
Wheel.
3. Alignment Criteria is to adjust these 2 screws until “No Dark Edges” and “No Shadows” can be
observed in image.
59
3. PC Alignment Procedure
Equipment：
Equipment：
- Pattern generator
OSD Default value：

value：
Item Value
Cal R Offset 512
Cal G Offset 512
Cal B Offset 512
Cal R Gain 1300
Cal G Gain 1300
Cal B Gain 1300
YPbPr R Offset 512
YPbPr B Offset 512
Procedure：
Procedure：
1. Connect power cord and PC D-sub source into projector.
2. Turn on projector.
3. Change Timing of pattern generator:
Timing: 1280*800@60Hz (WXGA models)
4. Change Pattern of pattern generator:
Pattern: Full frame pattern, ex.pattern1
5. Press “Auto” to catch the full screen
6. Change Pattern of pattern generator:
Pattern: A near white color (240,240,240) and a near black color(16,16,16)
7. Enter Factory mode, block 3
8. Press “Calibratio
Calibration
Calibration RGB <Press L or R>”
R> to let the black level to just distinguish, and the
light output of white level to just max.
9. Check the 32 levels of gray. All steps must appear.
10. Done
60
5. Level 2 Circuit Board and Standard Parts Replacement
Replacement
5.1 Product Exploded View

View
Module 1 – Total Exploded View
61
62
Module 2 – ASSY UPPER CASE
63
Module 3 – ASSY LOWER CASE
Module 4 – ASSY FRONT CASE
64
5.2 Product Disassembly / Assembly
MW814ST Dismantle SOP

Step Description Tool
Disassemble the Left case

screw*1 and take off the
lamp door. Lamp module Scerw*1
screw*
Disassemble the lamp
screw
1 module screw*1 and take off
driver
the lamp module, as the
right Figure .
Disassemble the upper case

screw*1.
upper case screw*1
1 4
Disassemble the lower case upper case hook

screw
2 screw*5, and take off the 3
driver
upper case(hook x7)
2
5
front case
Extract the IR Wire and the
speaker wire from
mainboard and take off the
front case module.
3
IR Wire
Push the boss behind, and speaker wire
take off the left case and
right case module.
left case
right case
4 3 2
Dismantle screw*8 and 8L

1 6 5 screw
4 screw *2 on rear case then 9 7 10 driver*2
take off rear case 8
65
Dismantle C/W FPC wire,
C/W sensor wire, blower fan
wire, ballast 5pin wire, outlet
5
fan wire on main board.
ballast 5pin wire
blower fan wire outlet fan wire

C/W sensor wire C/W FPC wire
Disassemble the screw*6, 1

and take off the sheild main
board . 1
6
BKT Main board screw
6 Disassemble the main board 4 5
driver
and take off the outlet fan.
2 3 ground connection screw
Disassemble the screw*3 and
take off the BKT main board 2
sheild main board
3
Extract the door switch wire, ballast 5pin wire

thermal wire, ballast 5pin gasket
wire.
Take off the Power board 2 screw

7
switch driver
Take off the gasket*1. wire 1
3
Disassemble the screw*3 and thermal wire
take off the Engine module.
screw *1
Disassemble the screw*1,
and take off the lamp box. lamp box screw*1
blower fan screw
9
Disassemble the screw*1, driver
and take off the blower fan
and blower nozzle.
blower nozzle
pad adjust push button
foor adjust body

Ceiling
Extract the rubber foot rear mount
*2, foot adjust rear, pad BAR SECURITY screw
screw
10 adjust, foor adjust body,
driver
spring slider and the push
BAR SECURITY
button in the lower case. foot adjust rear
Rubber
rubber foot
foot rear
rear *2
*2
66
MW814ST Engine Dismantle SOP
Step Description Tool
gasket
Take off the gasket*1.

1 Disassemble the Ring
Zoom.
Take off the LENS 1 screw

2
screw*3 driver
2
DMD
Disassemble the 2 4 chip board

screw*4, and take off
screw
3 the Heat-sink and
3 1 driver
DMD chip with Chip
BD.
sponge DMD
Disassemble the baffle
1
DMD and sponge
DMD.
screw
4 3 driver
Disassemble the
screw*3 and take off baffle DMD 2
the CW module.
Rotate to open the

switch on socket, and
5
take off the DMD
chip board.
67
5.3 Module Assembly Key Point - Optical Engine
1. Light Pipe Module assembly and overfill alignment

1.1 Assembly LP Module to HSG DMD
i. Assembly two Overfill adjustment screws (M2) to HSG DMD (Fig. 1-1).
** Adjustment criteria refer to below item 1.2 & Fig. 1-2.
ii. Press CLIP of BKT LP first and push it into the hole (Fig. 1-3).
iii. Hook Clip LP to HSG DMD, and lock with screw well. (Fig. 1-4).
iv. Placed LP Module on LP datum of “DMD HSG” and adjustment screw well, shown (Fig.
1-5).
v. Assembly “Baffle LP”, Hook top of Baffle LP first (Fig. 1-6) & Hook bottom of Baffle LP to
HSG DMD well (Fig. 1-7).
1.2 Overfill Adjustment @ LP Module
Overfill Adjustment Criteria:
i. Pre-assembly 2 adjusting screws. Criteria shown as Fig.1-4
ii. Alignment Sequence:
a. To adjust “Horizontal Adjustment Screw” firstly, and then “Vertical Adjustment
Screw”.
b. Refer to Fig. 1-4
1.3 For Overfill Re-adjustment:
a. Those 2 Adjustment Screws must be released closely to the “Pre-assembly” positions
first (Fig. 1-4).
b. Follow adjustment steps shown in Item 1.1-ii..
Overfill Vertical
Adjustment Screw M2
Overfill Horizontal
Adjustment Screw M2
Fig. 1-1
68
Pre assemble this screw not
over the side surface.
Pre assemble this screw not over

the bottom surface.
Fig. 1-2
Insert the LP Module
Fig. 1-3
69
2. Screw Well
1. Hook to HSG DMD
Fig. 1-4
Overfill adjustment screws

LP Datum of
DMD HSG
Fig. 1-5
70
1. Hook top of LP
Baffle first
Fig. 1-6
Check the Hole

Feature
2. Hook bottom of
LP Baffle well
Fig. 1-7
2. Assembly HSG ILL Module:

2.1 CM Assembly
i. Place “Clip CM Front” first, and screw well (Fig. 2-1).
ii. Insert Clip CM Side to Sub HSG (Fig. 2-2).
iii. Assemble CM to Sub HSG and to make CM contact Sub HSG datum Well (Fig. 2-3).
iv. Assemble Clip CM Up to Sub HSG & Check the feature for Clip CM Up XGA. (Fig. 2-4,).
v. To check and make sure Clip CM Up hooks the Sub HSG Well (Fig. 2-5).
vi. Paste “Sponge tube AL” on cannelure of ” HSG ILL” (Fig. 2-5).
71
Screw M2 well Assemble Clip CM side
well
Fig. 2-1 Fig. 2-2 Datum3
Datum1
Datum2
Fig. 2-3
Check Feature
Sponge
Hook
Fig. 2-4 Fig. 2-5
72
2.2 FM Module Assembly
i. Check mark point of FM and place FM on “Sub HSG” surface (Fig. 2-6-1, 2-6-2).
ii. Assemble “Clip FM Z5” to fix FM(Fig. 2-7).
iii. Check Clip FM hook Sub HSG Well (Fig. 2-8)
Assembly FM
Mark Point
Fig. 2-6-1 Fig. 2-6-2
Clip FM Z5 Clip FM hook to

Sub HSG
Fig. 2-7 Fig. 2-8
3. AL, HSG ILL and HSG DMD Assembly:

3.1 Placed “AL” on the “HSG DMD”. The “raised surface” of “AL” shall toward “DMD direction” (Fig.
3-1).
3.2 To assemble ”HSG ILL SUB Module” with “HSG DMD” and cover over on “AL” and the then lock
with screws(Fig. 3-2).
73
DMD Direction
AL
Fig. 3-1
Screw first
Screw finally
Fixed shafts&
holes
Fig. 3-2
4. DMD and Chip B/D Module:
4.1. Judge Chip B/D and DMD alignment keying first (Fig. 4-1, 4-2).
4.2. Alight keying and Assemble DMD to Chip B/D (Fig. 4-3).
4.3. Push DMD slightly and use screwdriver rotate clockwise button to lock (close notation) DMD on
Chip B/D (Fig. 4-4).
Fig. 4-1 Alignment keying Fig. 4-2
74
Open notation
Button
Close notation
Fig. 4-3 Fig. 4-4

4.4 Place Damper on the surface of Chip-BD Fig. 4-5.
Chip-BD Damper
.
Fig. 4-5
5. Assembly Optical ENG
5.1 Assemble “Baffle DMD” to “HSG DMD” (Fig.5-1).
5.2 Assemble “Sponge DMD” to “HSG DMD” (Fig.5-1).
5.3 Assemble Chip B/D Module to “HSG DMD” (Fig. 5-2 , Fig. 5-3).
Alignment keying
Sponge DMD
Baffle DMD
Fig. 5-1
75
Fixed shafts of
DMD HSG
Fig.5-2
Fixed holes of DMD
Fig.5-3
5.4 Assemble Thermal Pad & Gasket Hest-sink then place contact DMD (Fig. 5-4-1~2).
1.>Press center of Heatsink before assemble spring screw, then keeps press until spring screw
assembly finish.
2.>Pre-fastening Sequence: [ 1 ] - [ 2 ] - [ 3 ] - [ 4 ].
3.>Fastening Sequence: [ 2 ] - [ 1 ] - [ 4 ] - [ 3 ].
4.>Screw Torque must be confirmed to be 6 kg-cm.
76
Press Heatsink when
assemble spring screw
Fig. 5-4-1
○
3
○
1
○
4
○
2
Fig. 5-4-2
5.5 Assemble “CW Module” to “DMD HSG” and lock with screws well (Fig.5-5).
Screw well
Fig. 5-5
5.6 Assemble “BKT Link Lamp & CW shield” on “DMD HSG” and then screws well (Fig. 5-6).
77
Screw well
Fig. 5-6
5.7 Assemble “Sponge Adaptor” and lock with screws well.
Screw well
Fig.5-7
Fig.5-8
5.8 Assemble “Lens” and lock with screws well
78
i. Assemble Lens and the Assembly direction must be horizontal(Fig. 5-9)
ii. Pre-fastening Screws firstly. Screw Torque must be confirmed to be 1-2 kg-cm. (Fig. 5-11)
iii. Fastening the Screws well. Screw Torque must be confirmed to be 6.0-7.0 kg-cm. (Fig.
5-11)
iv. Place Frame to “low position” finally.
Assemble horizontally
Fig. 5-9
1. Pre-
Pre-fasting firstly,
firstly screw torque is 1-2 kg-cm.
2. Lock screws well, screw torque is 6-7 kg-cm
Fig. 5-10
5.9 Assemble Ring Focus well
Fig.5-11
79
5.10 Assemble Lamp Module to “BKT Link Lamp” and then lock with screw well (Fig. 5-13).
Fig.5-12
80
5.4
5.4 Module Assembly Key Point - Mechanical
1. Assembl
Assembly
embly sequence
(1) Lower case assembly sequence
rubber
rubber
Rear foot
Adjust foot rubber
Adjust foot
spring
Push button
81
Security bar
Ceiling
mount
screw
Sponge
(2) Assemble power board with ballast cable on lower case
Notice : power board must be under these 2 hook
82
Notice : power board must be
go through these 2 boss
(3) Assemble lamp box assy on lower case
Door switch wire
Lamp wire
Plug lamp wire first
83
1
3 : screw
Notice : lamp wire cable routing : Lamp wire must go under the ballast cable
(4) Assemble nozzle assy on lower case
Thermal
break wire
Text side
84
screw Go through the boss
(5) Cable routing of thermal break wire & door switch wire
(6) Assemble blower
Cable out
85
(7) Assemble engine assy and EMI gasket on lower case
2 1
screw
Gasket alignment
Blower cable
(8) Assemble main bracket

Stick mylar first
86
Clip: assemble before
assembling main bracket on
lower case
screw
screw
(9) Assembling axial fan
The side with ribs faces outside
87
(10) Assembling main board , plug connector.
CW FFC CW cable Ballast cable Blower cable Axial fan
(11) Assemble main shielding
1
2
6
Screw*6
Cable routing for CW cable
88
(12) Assembling rear case
3 5 6 7 8 9
2 1
10 4
0
(13) Assembling front case assy

a. assemble IR lens in front case
89
b. Assembly sequence of IR board
- plug IR cable into IR board
- assemble IR board into front case
(14) Assembling case inlet, case outlet, case front & plug wires
IR wire
Speaker wire
90
Dress IR cable into the slot of boss.
CW wire
91
(15) Assembling upper case
Sub upper case
Assemble keypad label
Alignment
Assemble keypad
Assemble sponge on Z_F cover
Alignment
92
screw
3
Press hook x7 in
4 1
6 5 7
When press 3 & 4, please press the location 3mm from the edge
93
(16) Assemble lamp
Plug connector first
(17) fasten screw x 5
94
Screw*5
(18) assemble lamp door
screw
95
5.5
5.5 Block Diagram
Figure 1 Main board & Input board Block Diagram
96
5.6
5.6 Trouble shooting
Chapter 1 System Analysis

Chapter 2 Optical & Optical Engine Trouble Shooting Guide
Chapter 3 Power Supply Trouble Shooting Guide
Chapter 4 LED Messages Definition
Chapter 5 Error Count Messages Definition
97
Chapter 1 - System Analysis
Step:
1. Check Lamp Door
Keypad LED OK No
2. Check Power Board and Interlock
3. Check Connection between PWR BD
and Main BD
4. Check Main Board
Yes
1. Check Lampen wire , Lamp wire and
No Ballast wire
2. Check C/W and wire connection
If Power On, Lamp On?
3. Check Main board
4. Check Lamp
5. Check Ballast
Yes
Yes 1. Check Input Cable

No Signal? 2. Check OSD Source set up
3. Check Main board
No
1. Check OSD Lamp Hours

Yes 2. Check Lamp Door
Power Auto Turn Off 3. Check Lamp still light or not?
4. Check Fan still spin or not?
5. Check Thermal status
No
1. Check Remote module battery
Yes 2. Check Remote module
IR Remote Control NG? 3. Check IR Receiver on Main board
4. Check IR Receiver on IR board
No
Yes 1. Check the connection between Main

Pixel Fail? BD and Chip BD
2. Check the connection between OP
engine and DMD Chip
3. Check Chip board
4. Check Main board
98
Chapter 2 Optical & Optical Engine Trouble Shooting Guide
No. Item Trouble Shooting Guide
1 Brightness 1. Change lamp
2 Uniformity 1. Change lamp
1. Check ADC calibration
2. Check user’s menu brightness & contrast are default
3 FOFO Contrast 3. Clean DMD
4. Clean PL
5. Check ILL stop assy
1. Clean PL
4 ANSI Contrast 2. Clean DMD
3. Change PL
1. Check color wheel delay
5 Color
2. Check CW 50% point. Replace CW if necessary
6 Color Uniformity 1. Change lamp
1. Refer to Item#2-1 (attached below)
7 Blue Edge 2. Change CM
3. Change SUB HSG
1. Refer to Item#2-1(attached below)
8 Blue/Purple Border 2. Change CM
3. Change SUB HSG
1. Change Projection Lens
9 Focus
2. Check parallel between PL datum and DMD
10 Dust Clean DMD
1. Check connector between chipBD and MainBD
2. Re-install DMD with chipBD
Horizontal/Vertical
11 3. Check if any pin of C-Spring is missing, damaged or dirty
Strips
4. Change new ChipBD/C-Spring
5. Change new DMD
12 Pixel Fail Change new DMD
2-1. “Blue Edge” Trouble Shooting:
I. Re-adjust “Overfill” first.
For Overfill Re-adjustment:
i. Those 2 Adjustment Screws must be released for around 2 mm first.
ii. Alignment Sequence:
c. To adjust “Horizontal Adjustment Screw” firstly, then “Vertical Adjustment Screw”.
d. Refer to Figure 2-1..
99
(2) Overfill Vertical
Adjustment Screw
(1) Overfill Horizontal

Adjustment Screw
Fig. 2-1
II. Re-assemble LP module—include LP, LP Baffle, LP clip.
100
Chapter 3 Power Supply Trouble Shooting Guide
1. Introduction
This document is prepared to be a guide to repair trouble sets, some problems happen more
frequently are taken as example in it.
2. Problems
(a) no power
No power
Check power BD
Is CN701 pin7 Yes

Change main BD
=3.3v?
No
Yes
Is door SW press Change power
down? BD
No
Check lamp door
(b)lamp
(b) can not turned on
101
Lamp can not turned on
has lamp wire connect No

correct?
(Ballast bd between lamp) Wire connect certainty
Yes
has power wire connect No

correct? Wire connect certainty
Yes
has enable wire connect No

correct? Wire connect certainty
Yes
102
A
No
Has TH breaker wire connect Wire connect certainty
correct?
(main bd to ballast bd)
Yes
No
Has color wheel operation Change color wheel
normally?
Yes
No
If change ballast bd, lamp
can be Change lamp
Turned on or not?
Yes
Change
ballast/power bd
103
Chapter 4 - LED Messages Definition
Lamp Temp Power Status Note

- - O Stand-by
- - G Powering up
- - G Normal operation
- - O Normal power-down cooling
R - R Scaler reset fail
R Download Updater
Burn-In Messages
- - G Burn-in ON
G G G Burn-in OFF
- - G Burn-in powering up
Lamp Error Messages
R - - Lamp error in normal operation
R - O Lamp is not lit up
Thermal Error Messages
Fan 1 error (the actual fan speed is ±25% outside the
- R -
desired speed)
R R
desired speed)
G R NA
desired speed)
O R NA
desired speed)
R R O Temperature 1 error (over limited temperature)
G R O Temperature 2 error (over limited temperature) NA
R R R Thermal Sensor 1 open error
G R R Thermal Sensor 2 open error NA
R R G Thermal Sensor 1 short error
G R G Thermal Sensor 2 short error NA
R G Fan IC #1 I2C Connection error G7931
O G Fan IC #2 I2C Connection error NA
R O Fans do not rotate in the process of powering up
System Error Messages
- - R Scaler’s shutdown fail
R - G CW start fail
104
Chapter 5 - Error Count Messages Definition
Error Count Definition Specification

LAMP Fail Error Lamp shutdown Detect LAMPLIT
FAN 1 Speed Error Blower Fan speed error SPEED OVER ± 25%
FAN 2 Speed Error Lamp Fan speed error SPEED OVER ± 25%
Sensor 1 Open Error Main Board sensor error Detect Sensor 1
Sensor 1 Short Error Main Board sensor error Detect Sensor 1
Temperature 1 Error Over limited temperature Detect Sensor 1
Color Wheel Error Color Wheel operation error Detect color wheel signal
Abnormal Power down System shutdown Detect cooling process
First Burn-In Error Minutes Error in Burn-In mode Detect Burn-In Error time
105
Appendix 1 – Screw List / Torque
model name -MW814ST(Mars)
MW814ST(Mars) (MD)
screw P/N description Torque Q'ty total
NO. Where use
Part name Type Head Length Surface (kgf-
(kgf-cm) Unit Q'ty
8F.VG564.8R0
speaker to inlet
1 SCRW TAP PAN tap PH 8 Ni 4.5+/-0.5 2 2
case
M3*8L NI D-PT
main bkt to lower
2
8F.VG524.6R0 case
5.5+/-0.5
2 SCRW TAP PH W/F tap PH 6 Ni nozzle to lower 4
1
M3*6L NI D-PT case
4.5+/-0.5 zoom cover 1
main shd to main
8F.HA334.6R0 5.5+/-0.5 5
bkt
SCRW TAP
3 mach PAN 6 Zn 5.5+/-0.5 main shd to op 1 7
FPHM3*6(6/1)TP-S
B-ZN upper case to main
5.5+/-0.5 1
bkt
M3 8F.1A724.8R0
4 SCRW MACH PAN mach PAN 8 Ni 4.5+/-0.5 lamp door 1 1
M3*8L B-NI
top to lower case 5
8F.VA564.8R0 lampbox to lower
1
5 SCRW TAP PAN tap PAN 8 Ni 6.5+/-0.5 case 9
M3*8L NI D-PT op housing to
3
lower case
8F.TA724.8R0
6 SCRW TAP FH tap FH 8 Ni 4.5+/-0.5 Audio connector 1 1
M3*8L B-NI
8F.5A524.6R0
SCRW MACH
7 mach FH 6 Ni 4.5+/-0.5 HDMI connector 1 1
FLAT M3*0.5P*6L
NI
8F.1D526.6R0 ceiling mount boss 3
SCRW MACH PAN
M4 8 mach PAN 6 Ni 5.5+/-0.5 main bkt to Power 4
EXT- TOO M4*6L 1
bd
NI
sum= 29
Standoff
NO. Where use
(kgf-cm) Unit Q'ty
8F.00649.120
rear case ==
#4-
#4-40 1 STAND OFF mach hex 8 NI 5.5+/-0.5 8 8
D-sub
XH4#-40X4+8.1 NI
Screws on Power
Power board
NO. Where use
(kgf-cm) Unit Q'ty
8F.1A524.8R0
IC == heatsink
M3 1 SCRW MACH PAN mach pan 8 ni 4.5+/-0.5 8 8
(power bd)
M3*8L NI
106
107
Appendix 2 - Code List: IR / RS232 / DDC Data
Remote Control Code:

1. IR Code
Ke Function Description Code Support ID and Protocol
y
1 Power This button will on/off the 0x02 Yes Frequency 38 KHz
projector.
2 Source This button will show available 0x04 Yes Protocol NEC Format
source options.
3 Auto This button will automatically 0x08 Yes Custom 0x0030
adjust projector’s picture quality. Code
4 Blank This button will turn projector 0x07 Yes
into/out of blank mode.
5 Mode When there is no OSD menu on 0x10 Yes
the screen, the button will change
picture mode.
When there is OSD menu on the
screen, this button will excite the
item chooser.
6 Menu/Exit This button will turn on/off OSD 0x0F Yes
menu.
7 Right This button will move the chooser 0x0E Yes
item to the right one.
8 Left When there is OSD menu on 0x0D Yes
screen, this button will move the
chooser item to the left one.
9 Up When there is no OSD on screen, 0x0B Yes
this button will correct optical
keystone in negative direction.
When there is OSD menu on
chooser item to the upper one.
10 Down When there is no OSD on screen, 0x0C Yes
this button will correct optical
keystone in positive direction.
When there is OSD menu on the
chooser item to the next one.
11 Freeze This button will freeze/ unfreeze 0x03 Yes
the image.
12 Volume + This button will magnify the 0x82 Yes
volume gradually.
13 Volume - This button will reduce the volume 0x83 Yes
gradually.
14 Timer on When the presentation timer is 0x25 Yes
off , this button will activate/ stop
the timer.
When the presentation timer is
on , this button will restart,
continue or turn off the timer.
15 Timer Setup This button will activate the 0x26 Yes
“Presentation Timer” setting.
16 Digital Zoom + This button will show 0x18 Yes
108
unsupported logo.
17 Digital Zoom - This button will show 0x19 Yes
unsupported logo.
18 Page Up By pressing “Page Up” button, 0x05 Yes
could enable Page Up function.
19 Page Down By pressing “Page Down” button, 0x06 Yes
could enable Page Down function.
20 Cotrast Displays the CONTRAST setting 0x11 No
bar.
21 SWAP 0x12 No
22 Aspect Select the display aspect ratios. 0x13 No
23 Mute Mutes the built-in speaker. 0x14 No
24 Enter Enter key for OSD menu. 0x15 No
25 Brightness Displays the BRIGHTNESS setting 0x16 No
bar.
26 Wireless 0x17 No
channel
27 Audio 0x1A No
28 PIP Turns the PIP window on or off 0x1B No
and makes related adjustments.
29 POP 0x1C No
30 PAP 0x1D No
31 Capture 0x1E No
32 S-video Displays the S-VIDEO source 0x1F No
selection.
33 Q? Starts the INFORMATION 0x20 No
function.
34 Timer ON 0x25 No
35 Timer Setup 0x26 No
36 RGBHV Displays the PC source selection. 0x40 No
37 RGB-PC1 Displays the PC 1 source selection. 0x41 No
38 DVI-D Displays the DVI-D source 0x42 No
selection.
39 DVI-A Displays the DVI-A source 0x43 No
selection.
40 DVI-I Displays the DVI-I source 0x44 No
selection.
41 RGB-PC2 Displays the PC 2 source selection. 0x45 No
42 Power Off Turns off the projector. 0x4E No
43 Power On Turns on the projector. Ox4F No
44 Comp2 Displays the COMPONENT 2 Ox50 No
source selection.
45 Comp1 Displays the COMPONENT 1 0x51 No
source selection.
46 CVBS-1 Displays the CVBS-1 source 0x52 No
selection.
47 CVBS-2 Displays the CVBS-2 source 0x53 No
selection.
48 S-video2 Displays the S-Video 2 source 0x54 No
selection.
49 HDMI Displays the HDMI source 0x58 No
selection.
50 ANA Selects the ANA aspect ratio. 0x70 No
51 04:03 Selects the 4:3 aspect ratio. 0x71 No
109
52 LB Selects the LB aspect ratio. 0x72 No
53 WIDE Selects the WIDE aspect ratio. 0x73 No
54 REAL Selects the REAL aspect ratio. 0x74 No
55 MEMORY1 Select the User memory settings. 0x75 No
58 Default 0x78 No
59 COLOR Displays the COLOR setting bar. 0x79 No
60 TINT Displays the TINT setting bar. 0x7A No
61 ACTIVE 0x7B No
62 IRIS Displays the setting bar for the 0x7C No
adjustment of the motorised
aperture lens IRIS.
63 Brilliant Color 0x7D No
64 Memory Select the User memory settings. 0x80 No
65 Volumn+ 0x82 No
66 Volumn- 0x83 No
67 Exit Goes back to previous OSD menu, 0x85 No
exits and saves menu settings.
68 Key Lock 0x87 No
69 PAN 0x88 No
70 Lens Displays the setting page for the 0x8A No
adjustment of the
motorised vertical Lens shift value.
71 Focus 0x8B No
72 Zoom 0x8C No
73 V-keystone 0x8E No
74 H-keystone 0x8F No
75 PIP Size 0x90 No
76 PIP Position 0x91 No
77 Return 0x92 No
78 My Screen 0x93 No
79 Pattern 0x94 No
80 On(Split 0x95 No
screen)
81 Off(Split 0x96 No
screen)
110
2. RS-
RS-232 Command Code
(Each input upper case and lower case character should be action)
Function Type Operation ASCII Support
Write Power On <CR>*pow=on#<CR> YES
Power Write Power off <CR>*pow=off#<CR> YES
Read Power Status <CR>*pow=?#<CR> YES
Write COMPUTER/YPbPr <CR>*sour=RGB#<CR> YES
Write COMPUTER 2/YPbPr2 <CR>*sour=RGB2#<CR> YES
Write Component <CR>*sour=ypbr#<CR> No
Write DVI-A <CR>*sour=dviA#<CR> No
Write DVI-D <CR>*sour=dvid#<CR> No
Write HDMI <CR>*sour=hdmi#<CR> No
Source Selection Write HDMI 2 <CR>*sour=hdmi2#<CR> No
Write Composite <CR>*sour=vid#<CR> YES
Write S-Video <CR>*sour=svid#<CR> YES
Write Network <CR>*sour=network#<CR> No
Write USB Display <CR>*sour=usbdisplay#<CR> No
Write USB Reader <CR>*sour=usbreader#<CR> No
Read Current source <CR>*sour=?#<CR> YES
Write Mute On <CR>*mute=on#<CR> YES
Write Mute Off <CR>*mute=off#<CR> YES
Read Mute Status <CR>*mute=?#<CR> YES
Write Volume + <CR>*vol=+#<CR> YES
Audio Control Write Volume - <CR>*vol=-#<CR> YES
Read Volume Status <CR>*vol=?#<CR> YES
Write Mic. Volume + <CR>*micvol=+#<CR> YES
Write Mic. Volume - <CR>*micvol=-#<CR> YES
Read Mic. Volume Status <CR>*micvol=?#<CR> YES
Write Audio pass Through off <CR>*audiosour=off#<CR> YES
Write Audio-Computer1 <CR>*audiosour=RGB#<CR> YES
Write Audio-Computer2 <CR>*audiosour=RGB2#<CR> YES
Audio source Write Audio-Video/S-Video <CR>*audiosour=vid#<CR> YES
select Write Audio-Component <CR>*audiosour=ypbr#<CR> YES
Write Audio-HDMI <CR>*audiosour=hdmi#<CR> YES
Write Audio-HDMI2 <CR>*audiosour=hdmi2#<CR> YES
Read Audio pass Status <CR>*audiosour=?#<CR> YES
Write Dynamic <CR>*appmod=dynamic#<CR> YES
Write Presentation <CR>*appmod=preset#<CR> YES
Write sRGB <CR>*appmod=srgb#<CR> YES
Write Bright <CR>*appmod=bright#<CR> No
Write Living Room <CR>*appmod=livingroom#<CR> No
Write Game <CR>*appmod=game#<CR> No
Picture Mode
Write Cinema <CR>*appmod=cine#<CR> YES
Write Standard <CR>*appmod=std#<CR> No
Write User1 <CR>*appmod=user1#<CR> YES
Write User2 <CR>*appmod=user2#<CR> YES
Write User3 <CR>*appmod=user3#<CR> No
Read Picture Mode <CR>*appmod=?#<CR> YES
Write Contrast + <CR>*con=+#<CR> YES
Write Contrast - <CR>*con=-#<CR> YES
Read Contrast value <CR>*con=?#<CR> YES
Picture Setting Write Brightness + <CR>*bri=+#<CR> YES
Write Brightness - <CR>*bri=-#<CR> YES
Read Brightness value <CR>*bri=?#<CR> YES
Write Color + <CR>*color=+#<CR> YES
111
Write Color - <CR>*color=-#<CR> YES
Read Color value <CR>*color=?#<CR> YES
Write Sharpness + <CR>*sharp=+#<CR> YES
Write Sharpness - <CR>*sharp=-#<CR> YES
Read Sharpness value <CR>*sharp=?#<CR> YES
Write Color Temperature-Warmer <CR>*ct=warmer#<CR> No
Write Color Temperature-Warm <CR>*ct=warm#<CR> YES
Write Color Temperature-Normal <CR>*ct=normal#<CR> YES
Write Color Temperature-Cool <CR>*ct=cool#<CR> YES
Write Color Temperature-Cooler <CR>*ct=cooler#<CR> No
Read Color Temperature Status <CR>*ct=?#<CR> YES
Write Aspect 4:3 <CR>*asp=4:3#<CR> YES
Write Aspect Auto <CR>*asp=AUTO#<CR> YES
Write Aspect Real <CR>*asp=REAL#<CR> YES
Write Aspect Letterbox <CR>*asp=LBOX#<CR> No
Write Aspect Wide <CR>*asp=WIDE#<CR> No
Write Aspect Anamorphic <CR>*asp=ANAM#<CR> No
Read Aspect Status <CR>*asp=?#<CR> YES
Write Digital Zoom In <CR>*zoomI#<CR> YES
Write Digital Zoom out <CR>*zoomO#<CR> YES
Write Auto <CR>*auto#<CR> YES
Write Brilliant color on <CR>*BC=on#<CR> YES
Write Brilliant color off <CR>*BC=off#<CR> YES
Read Brilliant color status <CR>*BC=?#<CR> YES
Write Projector Position-Front <CR>*pp=FT#<CR> YES
Table
Write Projector Position-Rear Table <CR>*pp=RE#<CR> YES
Write Projector Position-Rear <CR>*pp=RC#<CR> YES
Ceiling
Write Projector Position-Front <CR>*pp=FC#<CR> YES
Ceiling
Read Projector Position Status <CR>*pp=?#<CR> YES
Write Quick auto search <CR>*QAS=on#<CR> YES
Write Quick auto search <CR>*QAS=off#<CR> YES
Read Quick auto search status <CR>*QAS=?#<CR> YES
Write Direct Power On-on <CR>*directpower=on#<CR> YES
Write Direct Power On-off <CR>*directpower=off#<CR> YES
Operation Read Direct Power On-Status <CR>*directpower=?#<CR> YES
Settings Write Signal Power On-on <CR>*autopower=on#<CR> YES
Write Signal Power On-off <CR>*autopower=off#<CR> YES
Read Signal Power On-Status <CR>*autopower=?#<CR> YES
Write Standby Settings-Network on <CR>*standbynet=on#<CR> YES
Write Standby Settings-Network off <CR>*standbynet=off#<CR> YES
Read Standby Settings-Network <CR>*standbynet=?#<CR> YES
Status
Write Standby Settings-Microphone <CR>*standbymic=on#<CR> No
on
Write Standby Settings-Microphone <CR>*standbymic=off#<CR> No
off
Read Standby Settings-Microphone <CR>*standbymic=?#<CR> No
Status
Write Standby Settings-Monitor <CR>*standbymnt=on#<CR> YES
Out on
112
Write Standby Settings-Monitor <CR>*standbymnt=off#<CR> YES
Out off
Read Standby Settings-Monitor <CR>*standbymnt=?#<CR> YES
Out Status
Write 2400 <CR>*baud=2400#<CR> YES
Baud Rate Write 19200 <CR>*baud=19200#<CR> YES
Read Current Baud Rate <CR>*baud=?#<CR> YES
Read Lamp Hour <CR>*ltim=?#<CR> YES
Read Lamp2 Hour <CR>*ltim2=?#<CR> No
Write Normal mode <CR>*lampm=lnor#<CR> YES
Write Eco mode <CR>*lampm=eco#<CR> YES
Write Smart Eco mode <CR>*lampm=seco#<CR> No
Lamp Control Write Dual Brightest <CR>* lampm =dualbr#<CR> No
Write Dual Reliable <CR>* lampm =dualre#<CR> No
Write Single Alternative <CR>* lampm =single#<CR> No
Write Single Alternative Eco <CR>* lampm =singleeco#<CR> No
Read Lamp Mode Status <CR>*lampm=?#<CR> YES

Read Model Name <CR>*modelname=?#<CR> YES
Write Blank On <CR>*blank=on#<CR> YES
Write Blank Off <CR>*blank=off#<CR> YES
Read Blank Status <CR>*blank=?#<CR> YES
Write Freeze On <CR>*freeze=on#<CR> YES
Write Freeze Off <CR>*freeze=off#<CR> YES
Read Freeze Status <CR>*freeze=?#<CR> YES
Write Menu On <CR>*menu=on#<CR> YES
Write Menu Off <CR>*menu=off#<CR> YES
Write Up <CR>*up#<CR> YES
Write Down <CR>*down#<CR> YES
Write Right <CR>*right#<CR> YES
Write Left <CR>*left#<CR> YES
Write Enter <CR>*enter#<CR> YES
Write 3D Sync Off <CR>*3d=off#<CR> YES
Miscellaneous Write 3D Sync Top Bottom <CR>*3d=tb#<CR> YES
Write 3D Sync Frame Sequential <CR>*3d=fs#<CR> YES
Read 3D Sync Status <CR>*3d=?#<CR> YES
Write Remote Receiver-front+rear <CR>*rr=fr#<CR> No
Write Remote Receiver-front <CR>*rr=f#<CR> No
Write Remote Receiver-rear <CR>*rr=r#<CR> No
Read Remote Receiver Status <CR>*rr=?#<CR> No
Write Instant On-on <CR>*ins=on#<CR> No
Write Instant On-off <CR>*ins=off#<CR> No
Read Instant On Status <CR>*ins=?#<CR> No
Write Lamp Saver Mode-on <CR>*lpsaver=on#<CR> No
Write Lamp Saver Mode-off <CR>*lpsaver=off#<CR> No
Read Lamp Saver Mode Status <CR>*lpsaver=?#<CR> No
Write Projection Log In Code on <CR>*prjlogincode=on#<CR> No
Write Projection Log In Code off <CR>*prjlogincode=off#<CR> No
Read Projection Log In Code Status <CR>*prjlogincode=?#<CR> No
113
Write Broadcasting on <CR>*broadcasting=on#<CR> No
Write Broadcasting off <CR>*broadcasting=off#<CR> No
Read Broadcasting Status <CR>*broadcasting=?<CR> No
Write AMX Device Discovery-on <CR>*amxdd=on#<CR> YES
Write AMX Device Discovery-off <CR>*amxdd=off#<CR> YES
Read AMX Device Discovery Status <CR>*amxdd=?#<CR> YES
Read Mac Address <CR>*macaddr=?#<CR> YES
Write High Altitude mode on <CR>*Highaltitude=on#<CR> YES
Write High Altitude mode off <CR>*Highaltitude=off#<CR> YES
Read High Altitude mode status <CR>*Highaltitude=?#<CR> YES
Note: The above function will be vary from model to model. (ex: source, audio settings, aspect ratio..etc)
114
DDC
D-Sub
MW814ST Analog EDID
00 FF FF FF FF FF FF 00
09 D1 02 05 01 00 00 00
18 15 01 03 0E 00 00 78
0A C9 3D A2 5B 54 92 25
12 50 5D BD EF 80 81 3C
45 7C 61 7C 61 C0 81 80
95 00 90 40 A9 40 9E 20
00 90 51 20 1F 30 48 80
36 00 00 00 00 00 00 1C
00 00 00 FD 00 30 78 1F
66 11 00 0A 20 20 20 20
20 20 00 00 00 FE 00 42
45 4E 51 0A 20 20 20 20
20 20 20 20 00 00 00 FC
00 4D 57 38 31 34 53 54
0A 20 20 20 20 20 00 B6
115
HDMI
MW814ST Digital EDID
00 FF FF FF FF FF FF 00
09 D1 02 05 01 00 00 00
18 15 01 03 80 00 00 78
0A C9 3D A2 5B 54 92 25
12 50 5D BD EF 80 81 3C
45 7C 61 7C 61 C0 81 80
95 00 90 40 A9 40 9E 20
00 90 51 20 1F 30 48 80
36 00 00 00 00 00 00 1C
00 00 00 FD 00 17 78 1F
66 11 00 0A 20 20 20 20
20 20 00 00 00 FE 00 42
45 4E 51 0A 20 20 20 20
20 20 20 20 00 00 00 FC
00 4D 57 38 31 34 53 54
0A 20 20 20 20 20 01 5C
02 03 22 71 4F 15 06 1F
10 03 84 05 11 13 14 02
12 20 21 22 23 09 07 07
83 01 00 00 65 03 0C 00
10 00 02 3A 80 18 71 38
2D 40 58 2C 45 00 00 00
00 00 00 1E 01 1D 80 18
71 1C 16 20 58 2C 25 00
00 00 00 00 00 9E 01 1D
80 D0 72 1C 16 20 10 2C
25 80 00 00 00 00 00 9E
8C 0A D0 8A 20 E0 2D 10
10 3E 96 00 00 00 00 00
00 18 01 1D 00 BC 52 D0
1A 20 B8 28 96 40 00 00
00 00 00 1E 00 00 00 DD
116
Appendix 3 – Ceiling Mount Drawing
M4, max screw length (L),
L=ceiling arm thickness+8mm
117

Benq 9h.j4s77.14e

Uploaded by

Document Informationclick to expand document information

Document Informationclick to expand document information

Copyright:

Available Formats

Benq 9h.j4s77.14e

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Benq 9h.j4s77.14e

Uploaded by

Copyright:

Available Formats

Applicable Country & Regions:

Product Service Manual – Level 2

Service Manual for BenQ:

First Edition (May 2011)

2.3 Important Service Information

2.5 Compliance Statement

2.6 General Descriptions

2.7 Related Service Information

(2) Signal Level:

(3) Support Timings: (Version 01)

Horizontal Vertical Sub-carrier User Manual

1.1.2 S-Video Input

4-pin Mini Din Connector

1.1.3 Component Video Input

(2) Signal Level:

(3) Support Timings: (Version 01)

(2) Support Video Timings: (Version 01)

(4) Support Audio:

Pin Signal Parameter Min Type Max

(2) Signal Level: N/A

1.1.7 Audio Input (Mini-Jack φ3.5mm)

(2) Signal Level:

1.1.8 Audio Headphone Output (Phone-Jack φ3.5mm)

1.1.9 RS232 Control Port

(2) Signal Level:

(2) Signal Level:

Power Supply Specification

3.2 Varist Requirement

3.3 Lamp Power Requirement

ID Key Name Detailed Description

After put in Power cord & Warranty

After put in Power cord & Warranty

After put in Power cord & Warranty

The "Customer Acceptance Criteria" is applicable to the inspection of the projector,

The "Customer Acceptance Criteria" is the document defining the process of

5.0 CLASSIFICATION OF DEFECTS

The defects are grouped into the following classes:

5.3 Minor defect

6.0 EXPRESSION OF DEFECTIVES

7.0 INSPECTION STANDARD

7.1 Acceptance Quality Level

7.1.1 Critical Defect:

7.1.2 under normal sampling

Critical Defective : 0% AQL

8.0 GENERAL RULES

9.0 TEST CONDITIONS

Unless other prescription, the test conditions are as followings:

10.0 TEST EQUIPMENTS

ANSI Brightness、Bright Uniformity、FOFO

Full Red Impurity、CIE coordinate

Full Green Impurity、CIE coordinate

Full Blue Impurity、CIE coordinate

32 Gray Gray Check

Check the DDC information,

(b) Download Mode：

(d) Power Off：

B. Download MCU Code and Firmware