Tomcat I815e: Tyan S2060

Tyan S2060
Tomcat i815e
Motherboard User’s Manual
Revision 1.01
Copyright © Tyan Computer Corporation, 2000. All rights reserved. No part of this
manual may be reproduced or translated without prior written consent from Tyan
Computer Corp.
All registered and unregistered trademarks and company names contained in this
manual are property of their respective companies including, but not limited to the
following.
Tomcat i815e S2060 is a trademark of Tyan Computer Corporation.

AMI is a trademark of American Megatrends Incorporated
Windows is a registered trademark of Microsoft Corporation.
IBM, PC, AT, PS/2 are trademarks of IBM Corporation.
INTEL, Pentium III, Celeron are trademarks of Intel Corporation.
Red Hat Linux is a trademark of Red Hat Corporation.
Information contained in this publication has been carefully checked for accuracy and
reliability. In no event will Tyan Computer be held liable for any direct or indirect,
incidental or consequential damage, loss of use, loss of data, or other malady resulting
from errors or inaccuracies of information contained in this manual. The information
contained in this document is subject to change without notice.
Table of Contents
1. Introduction............................................................................................... 4
Overview......................................................................................... 4
Icons................................................................................................ 5
Hardware Specifications/Features.............................................. 6
Software Specifications................................................................ 8
Technical Support......................................................................... 8
Returning Merchandise for Service............................................ 8
2. Board Installation.................................................................................. 10
Unpacking.................................................................................... 10
Installation................................................................................... 10
Quick Reference for Jumpers..................................................... 12
Map of Motherboard Jumpers.................................................. 13
Setting Jumpers........................................................................... 15
Clear CMOS and Reset PW........................................................ 15
BIOS Flash TL.............................................................................. 15
Chassis Intrusion Alarm Connector.......................................... 16
Soft Power Connector................................................................. 17
Mounting the Motherboard in the Chassis............................. 18
Installing Memory........................................................................ 18
Installing the CPU and Cooling Fan......................................... 21
Connecting IDE and Floppy Drives......................................... 22
Installing Add on Cards ............................................................ 24
Connecting PS/2, USB, Ethernet*, Serial & Parallel Devices 25
Connecting the Power Supply................................................... 26
Ethernet Setup and Use*........................................................... 26
Frequently Asked Questions.................................................... 30
3. BIOS Configuration.............................................................................. 32
Main Setup................................................................................... 33
Advanced Menu......................................................................... 33
Configure Nat366 Serial Port(s) and Parallel Port................... 34
IDE Configuration....................................................................... 34
Floppy Configuration................................................................. 36
Boot Settings Configuration..................................................... 37
Event Log Configuration........................................................... 38
Chipset Menu.............................................................................. 39
GMCH Configuration.................................................................. 39
ICH Configuration.......................................................................... 41
PCI / PnP Menu.............................................................................. 41
Power Menu.................................................................................... 43
Boot Menu...................................................................................... 44
Security Menu................................................................................ 44
Exit Menu......................................................................................... 45
4. System Resources.................................................................................... 46
Beep Codes..................................................................................... 46
Troubleshooting System Problems............................................. 47
Displayed Error Messages........................................................... 48
Flash Utility..................................................................................... 50
Appendix - Glossary...................................................................................... 52
* Indicates an optional feature available on some models of Tomcat i815e.

Chapter 1
Introduction
1 chapter
Introduction
Overview
The Tomcat i815e is a quality, high performance motherboard designed for Socket 370
Type Intel Pentium III / Celeron microprocessors. The Tomcat i815e utilizes the Intel
i815e Chipset with AMI BIOS and can support CPU speeds of 500 MHz through
800 MHz, and host bus speeds of 66MHz to 133MHz. For CPU speed support,
please refer to the CPU Compatibility Chart in Tyan’s website:
http://www.tyan.com/support/html/pentiumii_iii_ppga.html
The Tomcat i815e motherboard, provides high performance capabilities that are ideal
for a wide range of demanding applications such as CAD, CAM, CAE, desktop
publishing, 3D modeling, animation, and video production.
This integrated high-performance system board in an ATX form factor offers more
features and expandability than other ATX boards in its class. Some of the features
included are onboard UltraDMA 66 / 100, onboard digital link sound (optional) and
built-in Intel 3D Graphics accelerator for enhanced graphics performance.
http://www.tyan.com
4
Flexibility and expandability have been designed into the Tomcat i815e.
With I/O and drive controller support built onboard (along with the many
INTRO
onboard features previously mentioned), the AGP 2x / 4x slot and six PCI slots
are free for more add-on expansion cards.
Remember to take a look at Tyan’s web site located at

http://www.tyan.com. There you can find information on all of Tyan’s products
along with FAQs, distributors list, drivers, and BIOS setting explanations.
Icons
In order to help you navigate this manual and set up your system, we have
added several icons to our format.
This icon alerts you to particularly important details regarding the

! setup or maintenance of your system. This icon often appears next to
important! information that may keep you from damaging your board or system.
While we will often point out the most vital paragraphs in a chapter,
you should always read every word in the text. Failing to do so can
lead to exasperation and expense.
1. Wherever possible, we have included step-by-step instructions for

2.
3. setting up your system, which are indicated by this icon. However, it
procedure
is in your best interest to read an entire section (and perhaps the
entire manual) before you begin to install your motherboard.
While we have alerted you to potential dangers in several places in

warning
the manual with this icon, these warnings should not be regarded as
the whole of your safety regimen. Never forget that computers are
electrical devices, and are capable of delivering a shock. Prevent
damage to yourself and to your board: always ensure that your
system is turned off and unplugged whenever you are working with
it, and that you are equipped with a static safety device. If a static
safety device is not available to you, remember to touch any un-
painted metal surface in your case before handling your board.
S2060 Tomcat i815e
5
Chapter 1
Introduction
Hardware Specifications/Features
Processor Information •Single PGA370 Socket
•Intel® Pentium III (FC-PGA) 500 mhz-800MHz*
•Intel® Celeron (FC-PGA) 533 mhz - 600 MHz*
•Intel® Celeron (PGA370) 300 mhz - 533 mhz*
•On-board VRM
•Frontside Bus support for 66 / 100 / 133 MHz
Expansion Slots •One 2x / 4x mode 3.3V / 1.5V AGP slot

•Six 32-bit PCI slots
•Total seven usable slots
Chipset Information •Intel® i815e AGPset

•MCH + ICH2 + FWH (4Mb)
•National PC87366 LPC Super I/O Chipset
Hardware Monitoring •National PC87366 hardware monitoring chip

•3-pin fan monitoring headers
•2-pin Chassis intrusion header
•Flexible temperature and voltage sensing
•3-pin Wake on LAN header (optional)
•3-pin Wake on Ring header (optional)
Memory*** •Three 3.3V 168-pin DIMM sockets

•Supports up to 512 MB PC100 / PC133
Unbuffered, non-ECC, non-registered SDRAM
Integrated PCI IDE •Dual channel master mode

•Up to four Enhanced IDE devices
•Support for UDMA 33/66/100 IDE drives and
ATAPI compliant devices
Integrated I/O •One Floppy connector for up to two drives

•Two 9-pin UART serial ports
(one port is via cable -optional)**
•One 25-pin ECP/PPP parallel port
•PS/2 keyboard and mouse ports
•Four USB ports (two ports via cable -optional)**
*** See Tyan website for Memory Compatibility details: http://www.tyan.com
http://www.tyan.com
6
Integrated LAN Controller •One Intel® ICH2 s/82562M “Kinnereth”
(Manfuacturing Option) controller
INTRO
•10/100 Mbps data transfer rate
•3-pin Wake on LAN (optional)
Integrated 2D/3D Graphics •Intel i815e D.V.M. Technology graphics core

•Integrated 230 Mhz DAC
•Integrated H/W Motion Compensation
engines
•Optional 4 MB PC133 SDRAM AGP In-Line
Memory Module (AIMM) to improve graphics
performance
•Standard 15-pin Analog VGA port
Integrated Audio •Software audio codec

(Manufacturing Option) •Line-in, line-out, mic and game / MIDI ports
•4-pin CD-ROM audio header (ATAPI)
BIOS •AMI BIOS 4 Mbit Flash

•Supports APM 1.2 & ACPI 1.0
•Auto detection of memory size
•Auto configuration of IDE hard disk types
•User settings of hardware monitoring
•Mutliple boot options
•DMI 2.0 compliant
Form Factor •ATX 2.03 (12” x 8”)

•One 20-pin ATX power connector
•Stacked mouse and keyboard ports
•Stacked two USB; one RJ-45 with LED
ports (optional)
•Stacked one serial, one video, and one parallel
port
•Stacked audio and game / MIDI ports (optional)
Regulatory •FCC Class B (Declaration of Conformity)

•European Community CE
(Declaration of Conformity)
* See Tyan website for CPU Compatibility List:

http://www.tyan.com/support/html/pentiumii_iii_ppga.html
** Extra cables available for sale at etyan: http://www.etyan.com
S2060 Tomcat i815e
7
Chapter 1
Introduction
Software Specifications
OS •Operates with Windows 98/ME,
Windows 2000, and Red Hat Linux 6.2
Technical Support
If a problem arises with your system, you should turn to your dealer for help first.
Your system has most likely been configured by them, and they should have the best
idea of what hardware and software your system contains. Hence, they should be of
the most assistance. Further, if you purchased your system from a dealer near you,
you can actually bring your system in to them to have it serviced, instead of attempt-
ing to do so yourself (which can have expensive consequences).
Help resources:
1. See FAQ and beep codes sections of this manual.
2. See Tyan web site for FAQ, bulletins, driver updates, etc: http://www.tyan.com
3. Contact your dealer or distributor for help BEFORE calling Tyan.
4. Check the Tyan user group: alt.comp.periphs.mainboard.tyan
Returning Merchandise for Service

During the warranty period, contact your distributor or system vendor FIRST for any
product problems. This warranty only covers normal customer use and does not cover
damages incurred during shipping or failure due to the alteration, misuse, abuse, or
improper maintenance of products.
For Resellers Only:

A receipt or copy of your invoice marked with the date of purchase is required before
any warranty service can be rendered. You can obtain service by calling the manufac-
turer for a Return Merchandise Authorization (RMA) number. The RMA number
should be prominently displayed on the outside of the shipping carton and the package
should be mailed prepaid, or hand-carried to the manufacturer. Tyan will pay to have
the board shipped back to you.
http://www.tyan.com
8
INTRO
This page left blank intentionally.
S2060 Tomcat i815e
9
Chapter 2
Board Installation
2 chapter
Board Installation
Unpacking
The motherboard package should contain the following:
(1) Tomcat i815e mainboard
(1) 34-pin floppy cable
(1) 80-wire, 40-pin ATA-66/100 IDE cable with blue connector included
(1) Tomcat i815e User’s Manual
(1) Driver CD
(1) I/O shield included (optional)
Installation
You are now ready to install your motherboard. The mounting hole pattern of the
Tomcat i815e matches the ATX system board specifications. Your chassis should
support a standard ATX mainboard form factor.
How to install our products right... the first time.

What’s the first thing I should do?
The first thing you should do is read this user’s manual. It contains important
information which will make configuration and setup much easier.
http://www.tyan.com
10
Here are some precautions you should follow when installing your motherboard:
(1) Ground yourself properly before removing your motherboard

from the antistatic bag. Unplug the power from your computer
and then touch any unpainted metal part on the computer case.
(Or wear a grounded static safety wrist strap.)
(2) Hold the motherboard by its edges and do not touch the bottom of
the board.
INSTALL
(3) Avoid touching motherboard components, IC chips, connectors,
and leads.
(4) Avoid touching pins of memory modules and chips.
(5) Place motherboard on a grounded antistatic surface or on the
antistatic bag.
Having reviewed the precautions above, the next step is to take the motherboard out of
the cardboard box and static bag, hold it by its edges, and place it on a grounded
antistatic surface, component side up. Inspect the board for damage.
! DO NOT APPLY POWER TO THE BOARD IF IT HAS BEEN DAMAGED!

important!
Press down on any of the socket ICs if it appears that they are not properly seated
(the board should still be on an antistatic mat). Do not touch the bottom of the board.
Remember, don’t take any electronic device out of its protective bag until you are
ready to actually install it into the computer case. If you do not ground yourself, you
risk zapping the motherboard or adapter card. Subsequent problems may not arise
immediately because electrostatic discharge damage unlike physical damage, causes the
device to fail over time.
1.
2.
Installation Steps
3. 1. Set Jumpers
procedure
2. Mount Motherboard in Chassis
3. Install Memory
4. Install CPU & Cooling Fan
5. Connect IDE and Floppy Drives
6. Install Add-on Cards
7. Connect PS/2, USB, Ethernet (optional), Serial and Parallel Devices
8. Connect Power Supply
S2060 Tomcat i815e
11
Chapter 2
Board Installation
Quick References for Jumpers

In this manual, the terms “closed” and “on” are used when referring to jumpers
(or jumper pins) that are active; “open” and “off” are used when referring to
jumpers (or jumper pins) that are inactive. See the Figure 2-1 for examples of
“on” and “off” pins and jumpers. The square pin in the diagram is Pin 1.
Jumpers and pins are connected by slipping the blue plastic jumper connector
overtop of two adjacent jumper pins (indicated by 1-2 or 2-3). The metal rod
inside the plastic shell bridges the gap between the two pins, completing the
circuit. See Figure 2-2 for more example of pin connections.
Figure 2-1 Figure 2-2
2 pin jumpers 3 (or more) pin jumpers
off on 1-2 2-3 open

1 1 1
2 2 2
3 3 3
The tables and maps on the following pages will help you set the jumpers for
CPU speed, Infrared, and external connector pin assignments, among others.
The miniature motherboard maps will help you locate the jumpers on your board.
A full-page map of the motherboard can be found on the next two pages.
http://www.tyan.com
12
Map of Motherboard Jumpers
Power Supply
Mouse
Keyboard
FAN1
LAN* FDD
INSTALL
2 USB Ports
Com1 Port
Intel® PGA 370 FSB 66/100/133 MHz

S-IDE
LPT1 Printer Port
Video Out
Game Port*
Intel® i815e
FAN2
FAN4
P-IDE
Mic*
Line-in*
1 AGP 2x / 4x 3 DIMM Sockets (PC100/133)
Line-out*
1 6 32-bit PCI slots
PJ2
Audio Codec* J29* J37*
1
Software audio codec*
J18
1
J13
1
Intel® i815e 1
J33
J15
J7 1
J34*
JP1
J8*
Battery FAN3
JP2
Super I/O J12

1 BIOS
J38
The tiny “1”s next to jumpers of 3 pins or more indicate the position of pin 1 for that jumper.
S2060 Tomcat i815e
13
Chapter 2
Board Installation
Map of Tomcat i815e Features

Ethernet*, 2 USB ports
Floppy connector
PS/2 Mouse & Socket 370 Type for ATX Power
Keyboard ports Celeron/PIII CPU Supply Header 3 DIMM slots
Parallel, COM1, VGA ports
Primary IDE
Secondary IDE
Joystick port*, mic*, line-in*, line-out*
AGPset
Intel i815e
USB Buzzer
Internal
Software audio codec*
Battery
6 PCI slots AGP National hardware AMI

2x / 4x slot monitoring chip (BIOS)
* Indicates optional feature available on some models of Tomcat i815e.
http://www.tyan.com
14
1. Setting Jumpers
Note: There are no Jumper settings for CPU bus speed or clock multiplier on the
Tomcat i815e board. The Tomcat i815e is designed to automatically detect the
socketed Pentium III / Celeron CPU and its proper speed settings.
1-A. J15 External Pin Assignments
Pwr/Slp
LEDs
HDD
VCC+ 1 2 Power LED+

LED
INSTALL
Ground 3 4 Sleep LED+
(Sleep)
Switch
Switch
Power
Reset
Ground 5 6 Power On/Off
Switch 7 8 Pwr On/Off GND
IR +5V 9 10 NO CONNECT
IR RX 11 12 Ground
Infrared
IR GND 13 14 NO CONNECT J15,

IR T X 15 16 NO CONNECT J33
IR RX2 17 18 NO CONNECT
JP1 (clear CMOS) JP2

1-B. Power LED (J33)
Pin 1 2 3 Jumper J33 is a 3-pin ACPI LED
+5 VSB VCC header. If you need a 2-pin Power
Ground LED header, use jumper J15 above.
LED YEL LED GRN
1-C. Clear CMOS and Reset Password (JP1)

D efault Reset
JP 1 1-2 2-3
If you have been locked out of your system because you forgot your password or set
the CMOS incorrectly, follow the instructions below.
1. Power off the system and unplug power cable from the motherboard.
2. Set jumper JP1 to pins 2 and 3.
3. Wait for 10 seconds, then return jumper JP1 to pins 1 and 2.
4. Plug in power cable and power on the system again.
By following this procedure, you will erase your password and reset the CMOS to the
BIOS defaults.
1-D. BIOS Flash TL (JP2)

Close Open
JP2 Unlock Lock Flash TL
By default, this jumper is set to OPEN (locked) position. Having the Top Lock (TL)
protection “locked” will allow normal system operation. Closing jumper JP2 (un-
! locked) will allow the BIOS to be flashed. NOTE: If the jumper JP2 is closed
(unlocked), and if failure occurs during a new BIOS flash, you run the risk of
important!
rendering your entire system unbootable. The “backup” protection of the Boot
Block will be lost.
S2060 Tomcat i815e
15
Chapter 2
Board Installation
1-E. Wake-On Ring Connector (optional) (J34)

Pin 1 2 3
+5 V SB Ground WOR
1-F. Wake-On LAN Connector (optional) (J8)

Pin 1 2 3
+5 V SB Ground WOL
1-G. Chassis Intrusion Alarm Connector (J7)

The jumper J7 connector is an intrusion alarm connector. When attached to the chassis,
this alarm will alert the system administrator when someone opens the system’s case.
1-H. Fan Connectors (FAN1,FAN2,FAN3,FAN4)

Pin 1 2 3
Ground +1 2 V Speed
Fan1 is for the CPU fan. Fan2, Fan3, and Fan4 connectors are for the Chassis Fans.
You can monitor the status of three of these Fans by using Intel’s LANDesk system
management software.
1-I. External Speaker Connector (J13)

The external speaker should be connected to pins 1-
4 of jumper J13. FAN1
Pin 1 2 3 4
V CC ~ Buz z er SpkDrv
FAN2,
1-J. CD Audio Connector (optional) (J29) FAN4 J29,
J37
Pin 1 2 3 4 PJ2
CD-L Ground Ground CD-R J13
1-K. AUX Audio Connector (optional) (J37) FAN3
Pin 1 2 3 4 J34, J38 J7
L Ground Ground R J8
1-L. COM2 port header (PJ2)
This is the connector header for the COM2 Port (see p. 30 for availability of cable).
1-M. LAN EEPROM Enable/Disable (optional) (J38)

Enable Dis able
J38 1- 2 2- 3
By default, jumper J38 is set to ENABLE (close pins 1-2). Disabled settings are
reserved and settings should remain default. The LAN EEPROM contains the
configuration data for the LAN controller. Enabling J38 will allow normal operation of
the LAN EEPROM.
http://www.tyan.com
16
1-N. Front Side USB Header (J18)
Certain computer chassis allow for two front-end USB port connections. This board
provides a front side USB header should you decide to
set up a USB connector at the front side of your
computer. Note: The front side USB header supports
a seperate channel from the rear USB ports.*
1-O. External HDD LED (J12)
INSTALL
Connecting J12 to an external device (i.e. SCSI card) will
result in the LED output of the device to be redirected to
the front panel HDD LED.
J18
Soft Power Connector
The Soft Power Connector is part of jumper block J15
(pins 6-8). The Tomcat i815e uses the chipset for power
management, including turning on and off the system. If J12
the Power Button Function option in the BIOS Power
Management Menu is set to On/Off (which is the default), pressing the power button
once after the BIOS has booted up will turn the system on and off. If the Power
Button Function option is set to Suspend, pressing the power button once will wake
the system or send it to Suspend mode. In this case, you cannot turn the system off
unless you shut down through the Windows operating system or you hold the power
button down for four seconds.
Hardware Reset Switch Connector Installation

The Reset switch on your case’s display panel provides you with the Hardware Reset
function, which is the same as power on/off. The system will do a cold start after the
Reset button is pushed.
CMOS RTC
The Real Time Clock (RTC) circuit, which provides the date and time for the system is
integrated into the i815e chipset. If the external battery for the RTC is low, it will
prevent your system from POSTing, and you will not get a display. Normally the life
span of an external battery is 2 years. If yours is running low, you will need to replace
it with a new 3V lithium battery (Sony CR2032).
Flash EEPROM
The Tomcat i815e uses flash memory to store BIOS firmware. It can be updated as
new versions of the BIOS become available. You can upgrade your BIOS easily using
! the Flash Writer Utility (see page 50). NOTE: Please be aware that by flashing
your BIOS, you agree that in the event of a BIOS flash failure, you must contact
important!
your dealer for a replacement BIOS. There are no exceptions. Tyan does not
have a policy of replacing BIOS chips directly with end users. In no event will
Tyan be held responsible for damage done to the BIOS by the end user.
* Extra cables available at etyan: http://www.etyan.com

S2060 Tomcat i815e
17
Chapter 2
Board Installation
2. Mounting the Motherboard in the Chassis

Follow the instructions provided by the case manufacturer for proper installation
guidelines. Tyan recommends that you make use of all mounting holes to screw down
the motherboard. The adapter cards and the screws holding them down will keep your
board flat. The fastening screws should not short / touch any of the traces on the
motherboard. Make certain that you do not overtighten the screws, as that will damage
the motherboard and possibly break internal traces in the surrounding area. The hole
you should use is located at the top-center of the board where the adapter cards are
fastened to the case.
3. Installing Memory
Since Tyan boards are manufactured with performance in mind, you should use add-in
components that match. Some DIMM modules may seem to be high quality because of
name or feel but that does not guarantee real-world usability. Some cheaper or OEM
memory may have brand-name components, but they may contain inferior or substan-
dard parts which do not meet the critical tolerances our products require. Because of
this, your memory may not work correctly in a Tyan board though it may work well in
a competitor’s board. This is because many of our competitors do not adhere to the
strict tolerances required for high performance. If you buy a Tyan board, you are
Figure 2-3
http://www.tyan.com
18
getting the best system available. To make installation easy and trouble free, get high
quality parts. For a list of recommended memory vendors, please visit Tyan’s website
at www.tyan.com - go to the “Memory Support” area in the Support Section. The
website memory compatibility lists include DIMMs that have proven to be very stable
on our boards and perform extremely well.
To install your DIMMs, line your module up so that the pins fit into the slot. There
is only one way that your DIMM can fit properly. Make sure that the short row of
INSTALL
pins is lined up with the short gap in the DIMM slot. Figure 2-3 (previous page)
shows how to sit the DIMM into its slot. To insert the DIMM, push down vertically
on the module with even force, as shown in the photo. Do not shove one end in first;
doing so will bend the DIMM pins.
To lock the DIMM into place, push the plastic clips on either end of the slot onto the
notches in the ends of the DIMM (see Figure 2-4 below). In some cases, pushing the
memory module into the DIMM slot will move the plastic clips inward, automatically
locking the module into place. To remove your DIMM, simply pull the clips back, and
pull up on the module.
Figure 2-4
Place the DIMMs in an anti-static bag as soon as you remove them to avoid static
damage.
S2060 Tomcat i815e
19
Chapter 2
Board Installation
The Tomcat i815e uses a 64-bit data path from memory to CPU and can accommodate
up to 512MB of SDRAM. The 168-pin DIMMs (Dual In-line Memory Modules)
! must be of the 3.3V, unbuffered variety. The position of the notch in the SDRAM
key position will tell you whether or not a DIMM is unbuffered (see the Figure 2-5
important!
below). All installed memory will be automatically detected, so there is no need to set
any jumpers.
EEPROM
RFU Unbuffered 168-pin DIMM

Buffered
Figure 2-5
Some details of memory installation:
• The mainboard supports 32MB, 64MB, 128MB, and 256MB unbuffered DIMMs.
• There is a limit of two double-sided PC-133 DIMMS that can be installed.
• No ECC type memory can be used.
warning • Warning! DO NOT use registered DIMMs. (Check with your memory dealer
for more information). See www.tyan.com for the latest memory compatibility
information.
The table below shows some of the possible memory configurations. Not all
possible configurations are listed.
D IM M Bank 1 D IM M Bank 2 D IM M Bank 3 Total
32MBx1 32MBx1 0 64MB
0 32MBx1 32MBx1 64MB

64MBx1 32MBx1 0 96MB
32MBx1 32MBx1 32MBx1 96MB
64MBx1 64MBx1 0 128MB
0 64MBx1 64MBx1 128MB
64MBx1 128MBx1 192MB
0 128MBx1 64MBx1 192MB

128MBx1 128MBx1 0 256MB
0 128MBx1 128MBx1 256MB
128MBx1 256MBx1 0 384MB

0 256MBx1 128MBx1 384MB
256MBx1 256MBx1 0 512MB
0 256MBx1 256MBx1 512MB
http://www.tyan.com
20
4. Installing the CPU and Cooling Fan
Socket 370 type Pentium III / Celeron processors can be used on the Tomcat i815e.
Remember:
• The CPU is a
sensitive electronic
component and it can
INSTALL
easily be damaged by
static electricity. Do
not touch the CPU
pins with your
fingers.
• Before the CPU is
installed, the
mainboard must be
placed on a flat
surface. You should
be able to insert the
CPU into the socket
with minimal, but firm
pressure. Do not
press down hard on
the CPU.
Figure 2-6*
Pin 1 on the CPU is denoted by a small dot on one of the corners and Pin 1 on the ZIF
socket is denoted by an angled corner (see Figure 2-6). Never force a CPU into a
socket. Forcing a CPU to seat will bend the pins on the CPU and possibly damage the
motherboard.
Push down lightly on the CPU, and lower the arm on the ZIF socket to secure the
CPU. A squeaking noise is normal as the arm lowers. After the CPU is securely seated,
! you must install an appropriate cooling device (otherwise damage will occur to your
CPU). Tyan strongly recomends a heatsink / fan combination. Consult with your case
important!
manufacturer for other cooling
options.
Locate the cooling fan connector (e.g.

FAN1) on the motherboard. Plug the
CPU’s cooling fan cable into the
cooling fan connector on the board.
There will be a plastic clip assembly
similar to that of the ATX power
connector that will force you to
connect the fan cable correctly (see Figure 2-7
Figure 2-7 to the right).
* Image not representative of actual Tomcat i815e socket. It is provided as an example only.
S2060 Tomcat i815e
21
Chapter 2
Board Installation
5. Connecting IDE and Floppy Drives

The colored stripe on a ribbon cable should face toward the ATX Power Connector on
the motherboard. In Figure 2-8 (below), you can see how the IDE cables should look
when they are connected to your hard drive. Notice how Pin 1 (denoted by a colored
stripe) is connected so that it is next to the power connector of the drive. The primary
IDE connector is black; the secondary IDE connector is white. In most cases, this is
the proper way of connecting your IDE cable to the hard drive. Figure 2-9 on the next
page shows the IDE cable properly connected to the motherboard. Contact your hard
disk drive manufacturer or documentation for more information.
Figure 2-8
ATA-66/100 IDE hard drives require a special 80 pin IDE cable which has additional
grounding wires. The cable is included in the motherboard package, and is required
when using ATA-66/100 drives. This cable will also support all legacy IDE drives.
! (Note: The BLUE end of the ATA-66 cable must connect to the motherboard.)
Some symptoms of incorrectly installed HDDs are:
important!
• Hard disk drives are not auto-detected: may be a Master / Slave problem or a bad
IDE cable. Contact your vendor.
• Hard Disk Drive Fail message at bootup: may be a bad cable or lack of power
going to the drive.
• No video or beeps on bootup: usually means the cable is on backwards.
• Hard drive lights are constantly on: usually means bad IDE cable or defective
drives / motherboard. Try another HDD.
• Hard drives do not power up: check power cables and cabling. May also be a bad
power supply or IDE drive.
http://www.tyan.com
22
INSTALL
1
Figure 2-9
*Note: The images above is used to illustrate a concept and may not represent
the actual image of your motherboard.
warning Note: Only Tyan-approved cables will work on this motherboard. If you are
using an existing case with old cables, your system may not function properly.
Use only Tyan-approved cables.
Connecting Floppy Drives

Pin 1 on the floppy cable is usually denoted by a red or colored stripe down one side
of the cable (see Figure 2-10 below). Most of the current floppy drives on the market
require that the colored stripe be positioned so that it is right next to the power
connector. In most cases, there will be a key pin on the cable which will force you to
connect the cable properly.
Figure 2-10
S2060 Tomcat i815e
23
Chapter 2
Board Installation
Drive A: is always attached to the end of the cable with the twist in it. Drive B: is
always connected to the middle of the cable. Refer to your installation instructions or
call your dealer if you are unsure about attaching floppy drives. Refer to Figure 2-10
for a detailed anatomy of the floppy cable.
Remember, you can only have 2 floppy drives connected at any given time.
Some symptoms of incorrectly installed floppy drives are:
• Floppy drives are not detected: usually caused by faulty cables, backward
cables, or a bad floppy or motherboard. Try another single floppy drive to
verify the problem or try another cable. Also, check to see if the onboard floppy
is enabled in the BIOS.
• Floppy Drive Fail message at bootup: the cable, floppy, or motherboard
may be faulty. Try another cable or floppy drive to verify.
• Light on the floppy is on constantly: normally signifies that the cable is on
backwards. Reverse the cable at the motherboard end and try again.
6. Installing Add-on Cards

There are a few rules you need to follow when plugging in a card. In order to assure
proper operation and a quick installation, adhere to these guidelines:
• Installing an AGP card will automatically

disable the onboard VGA.
• If you are going to install a soundcard, the
onboard sound must be manually disabled through
the BIOS first.
! • NEVER force a card into a slot. If it doesn’t fit,
look at the socket on the computer to make sure
AGP
slot
important! there are no wires or other obstructions to the slot.
• When plugging the card in, especially when
installing long cards, try to push the entire card in
at one time. Don’t force one end of the card into
the socket first and then the other. This will
create a rocking motion between the card and the slot and it will damage the pins
within the socket.
• Make sure that the cards are seated securely into the slots.
• Before turning on the system, make sure no cards are touching each other.
warning • NOTE: This mother board operates on a 3.3V standby for PCI v2.2.
Because of this, you need to UNPLUG the AC power cord before
installing your card. Otherwise, the motherboard may automatically
power up when the card is inserted into the slot.
http://www.tyan.com
24
If you follow these basic guidelines, there shouldn’t be any problems with installation.
However, if you do encounter any problems, have a qualified professional install your
cards for you or contact your card manufacturer.
Remember, always read the manuals and installation notes that come with the adapter
cards. They contain important information which will help you install the components
right, the first time.
INSTALL
7. Connecting PS/2, USB, Ethernet*, Serial and
Parallel Devices
This board includes ports for USB, Ethernet*, PS/2 mouse, and PS/2 keyboard devices.
Note that, for this board, the mouse port is the upper PS/2 port, and the keyboard port
is the lower PS/2 port.
The PS/2 connectors are probably quite familiar to you, while the Universal Serial Bus
(USB) connectors, may not be. The USB port can function as a serial, parallel, mouse,
keyboard, or joystick port. It is fast enough to support video transfers, and is capable
of supporting up to 127 daisy-chained peripheral devices. Figure 2-11 (below) shows
the ATX double row connectors on this board. The Ethernet*, Serial, and Parallel
ports, as well as the other ports, are labeled.
PS/2 mouse Ethernet* LPT MIDI* / Game Port*
PS/2 keybrd USB O/1 COM1 Video-out Line-out* Line-in* Mic-in*

Figure 2-11
Connecting Serial and Printer Ports

Warning: When plugging in your keyboard and mouse, or when plugging anything into
a serial or parallel port, make sure that the power is off. Connecting these devices and
ports while the power is on is called “hot plugging,” and may damage your system.
S2060 Tomcat i815e
25
Chapter 2
Board Installation
8. Connecting the Power Supply

The Tomcat i815e requires an ATX power supply. Tyan recommends using one that
conforms to industry standard revision 2.01. The photos below show the ATX power
connector before (Figure 2-12) and after (Figure 2-13) it has been plugged in. The
plastic clip on the power connector should lock over the plastic tab on the onboard
connector. You shouldn’t be able to plug the power connector in any other way but
just to be safe, make sure it looks like Figure 2-13 below.
Make certain that you do not miss connecting any pins because if you do, you will
void your warranty and cause damage to yourself or your motherboard when you turn
the system on. After connecting the power, make sure the connector is seated firmly
into its socket so it will not become loose or fall off when the computer is jostled or
moved. NOTE: When installing your power supply, make sure the power supply
switch is turned ‘OFF’. You may turn the switch back ‘ON’ once you’ve finished
building your system.
Figure 2-12 Figure 2-13
Ethernet Setup and Use*

Cetain models of the Tomcat i815e motherboards have the optional Intel 82562ET 10/
100 Ethernet controller onboard. For more information, data sheets, white papers, or
demos, visit the Intel Network Products web site at: http://www.intel.com/network
http://www.tyan.com
26
Configuration and Drivers
The Ethernet driver cannot be installed directly from the TYAN Driver CD. Before
installing the Intel 82562 Ethernet drivers, the complete LAN 82562 directory and all
it’s contents must first be copied from the TYAN Driver CD onto your hard drive. The
82562 driver can then be installed from your hard drive.
Connecting the Network Cable

Connect a single network cable to the Ethernet adapter (see Figure 2-14). The cable
INSTALL
will only fit one way. For 100BASE-TX, your network cable must be category 5,
twisted-pair wiring. If you plan on running the adapter at 100 Mbps, it must be
connected to a 100BASE-TX hub (not a 100BASE-T4 hub). For 10BASE-T, use
category 3, 4, or 5 twisted-pair wiring.
100BASE-T Wiring: Twisted Pair Ethernet (TPE)

Use category 5 cable and an RJ-45 connector for this adapter. Do not use category 3
! wiring at 100 Mbps. At 100 Mbps, connect to a TX hub, not a T4 hub. NOTE: To
configure the adapter for your operating system, please refer to your operating
important! system’s documentation.
Troubleshooting
If the adapter can’t connect to the network:
· Make sure the cable is installed properly. The network cable must be securely
attached at both RJ-45 connections (adapter and hub). If the cable is attached but
the problem persists, try a different cable. The maximum allowable distance from
adapter to hub is 100 meters. If you’re directly connecting two computers (no
hub), use a crossover cable. Most hubs require a straight-through cable, while
most switches require a crossover cable (see your hub or switch documentation to
verify).
· Check the LED lights on the adapter. The 100 Mbps LED Link LED
onboard cable connector has
two diagnostic LEDs. These lights help
indicate if there’s a problem with the
connector, cable, or hub. The table below
describes the LEDs, and the drawing on the Y G
previous page shows their location (see
Figure 2-14).
· Make sure you’re using the correct drivers.

Make sure you’re using the drivers that
come with this adapter.
Figure 2-14
warning · Make sure the hub port and the adapter have the same duplex setting. If you
configured the adapter for full duplex, make sure the hub port is also configured
for full duplex. Setting the wrong duplex mode can degrade performance, cause
data loss, or result in lost connections.
S2060 Tomcat i815e
27
Chapter 2
Board Installation
Testing the adapter

Test the adapter by running Intel diagnostics. For Windows 95/98/2000 and Windows
NT run Intel PROSet by double-clicking the Intel PROSet Icon in the Control Panel.
Click Help from the main PROSet window to get complete diagnostics information and
instructions.
LED Indication Function
The a d a p te r a nd hub ha ve a c k no wle d g e d a c o nne c ti o n;

LNK On
the li nk b e twe e n the hub a nd a d a p te r i s g o o d .
T h e c a b l e c o n n e c t i o n b e t w e e n t h e h u b a n d a d a p t e r i s f a u l t y,
(green) Off
o r yo u ha ve a d r i ve r c o nfi g ur a ti o n p r o b le m .
100 On Ne two rk c o nne c ti o n o p e ra ti ng a t 1 0 0 Mb p s .
(yellow ) Off Ne two rk c o nne c ti o n o p e ra ti ng a t 1 0 Mb p s .
Ethernet Technical Information

Fast Ethernet Wiring
100BASE-TX Specification: The 100BASE-TX specification supports 100Mbps
transmission over two pairs of category 5 twisted-pair Ethernet (TPE) wiring. One pair
is for transmit operations and the other for receive operations. Segment lengths are
limited to 100 meters with 100BASE-TX for signal timing reasons. This complies with
the EIA-568 wiring standard.
Fast Ethernet Hub and Switches

The two basic types of hubs are shared hubs and switching hubs. Intel PRO/100+
adapters can be used with either type of hub for 10Mbps. At 100Mbps, a TX hub or
switch is required.
Shared hubs
In a shared network environment, computers are connected to hubs called repeaters. All
ports of the repeater hub share a fixed amount of bandwidth, or data capacity. On a
100Mbps shared hub, all nodes on the hub must share the 100Mbps of bandwidth. As
stations are added to the hub, the effective band-width available to any individual
station gets smaller. Shared hubs do not support full duplex. Think of a shared repeater
hub as a single-lane highway that everyone shares. As the number of vehicles on the
highway increases, the traffic becomes congested and transit time increases for
individual cars.
http://www.tyan.com
28
On a shared hub all nodes must operate at the same speed, either 10Mbps or
100Mbps. Fast Ethernet repeaters provide 100Mbps of available bandwidth, ten times
more than what’s available with a 10BASE-T repeater.
Repeaters use a well-established, uncomplicated design, making them highly cost
effective for connecting PCs within a workgroup. These are the most common type of
Ethernet hubs in the installed base.
Switching hubs
INSTALL
In a switched network environment, each port gets a fixed, dedicated amount of
bandwidth. In the highway scenario, each car has its own lane on a multi-lane highway
and there is no sharing. In a switched environment, data is sent only to the port that
leads to the proper destination station. Network bandwidth is not shared among all
stations, and each new station added to the hub gets access to the full bandwidth of the
network.
If a new user is added to a 100Mbps switching hub, the new station receives its own
dedicated 100Mbps link and doesn’t impact the 100Mbps bandwidth of another
station. Switching hubs can effectively increase the overall bandwidth available on the
network, significantly improving performance. Switching hubs can also support full
duplex.
For more information on Fast Ethernet, visit the Intel Network Products website:
http://www.intel.com/network
You are done!

Other than checking the jumper settings and cable connections, and putting the case
back on, you are done. Installing a new motherboard may sound difficult, but by
following these directions, you should have a fairly uneventful time installing our
products. If you do encounter problems, your dealer will be able to help you, or you
can consult one of our many technical support resources (see page 8).
S2060 Tomcat i815e
29
Chapter 2
Board Installation
Frequently Asked Questions

Q: My system sometimes becomes unstable. How should I check the system?
A: The first thing to do is to check and see if you have any device conflicts in IRQ, or
DMA. If you are using Windows 98/2000, the Control Panel is a good place to start.
Please consult your operating system manual for details. Second of all, slowing down
the memory timing in the BIOS’s chipset setup section will help the situation, as well.
Many memory modules are not suitable for high performance systems and are
probably the main source of your problem.
Q: How do I find out what memory will work with my motherboard?

A: Memory compatibility information can be found on Tyan’s web site at:
http://www.tyan.com
Q: Where can I get USB and flat serial cables for my motherboard?
A: You can purchase USB and serial cables from www.etyan.com. USB cables are also
available at www.wiretekusa.com (Tyan USB Cable Part #S1606-001-01)
Q: What is the USB pin out information for Tyan motherboards?

A: Please refer to URL link here: http://www.tyan.com/techref/html/io_usb.html
Q: My motherboard is dead, how do I return it?

A: Contact the place of purchase or your distributor for assistance to return the
motherboard for service. RMA issues will not be handled via email by Tyan Tech
Support. Please refer to URL link here for more details:
http://www.tyan.com/support/html/rma_faq.html
Q: How do I upgrade my BIOS?

A: BIOS update files and instructions on how to install them are available from the
Tyan web site at: http://www.tyan.com
Q: Is my motherboard Y2K compliant?

A: Please refer to URL link here: http://www.tyan.com/support/html/year2000.html
Q: Why do I get a "CMOS checksum invalid" error message during POST?

A: If you get the above error message or "Invalid configuration, run Setup" message,
the it is an indication that the CMOS battery may need to be changed, or simply reset
the CMOS and see if that solves the problem. If all else fails, contact your dealer for
assistance.
http://www.tyan.com
30
INSTALL

S2060 Tomcat i815e
31
Chapter 3
BIOS Configuration
3 chapter
BIOS Configuration
Introduction to Setup
The BIOS is the basic input output system is required by the computer to perform
functions such as CPU and hard drive support. This chapter decribes different settings
for AMIBIOS that can be use to configure your system.
! The BIOS section of the manual is subject to change without notice and is
provided here for reference purposes only. The settings and configurations of
important!
the BIOS are current at the time of print, and therefore they may not be exactly
the same as that displayed on your screen.
You can select a Setup option by using the following keyboard keys:
Key Function
Tab Moves from one selection to the next
Left/Right Arrow Keys Changes from one menu to the next
Up/Dow n Arrow Keys Move betw een selections
Enter Opens highlighted selection
PgUp/PgDn Change setting
The pages which follow contain explanations of the settings for the AMIBIOS Setup
menus. Drawings have been included for ease of reference. Overall, the AMIBIOS
Setup program is easy to use, and fairly intuitive. Note that the graphics in the manual
are simpler than those that appear on your screen.
http://www.tyan.com
32
Main Setup
Select the AMIBIOS Setup options by choosing Main Setup from the AMIBIOS
Setup main menu. The other sub screens (e.g. Main, Advanced, Chipset, PCIPnP,
Power, Boot, Security, and Exit) are accessible by using the ← → keys.
System Date/Time
You can type the date and time in directly, or select the portion of the date or time that
you want to modify and adjust it using the ↑ ↓ cursor keys. The clock runs on a 24-
hour cycle (i.e. 1:00 PM is 13:00).
General Help
At any time, you can press F1 to bring up a General Help screen in case you want to
learn the shortcut commands. There are two settings you should be aware of.
Load Failsafe Defaults If your system is experiencing configuration problems,
BIOS
you can choose this option to reset all settings.
Load Optim al Defaults This w ill load preset options that are designed for
maximum system performance, but may not w ork for all
computer applications. You should not use this option if
your is experiencing configuration problems.
Advanced Menu
In the Advanced setup (shown below) you can setup your system devices, boot
options, and more. Each option has a configuration sub screen (denoted by the
symbol).
BIOS SETUP UTILITY
Main Advanced Chipset PCIPnP Power Boot Security Exit
Setup Warning Configure SuperIO

Setting items on this screen to incorrect values Chipset Nat366
may cause the system to malfunction!
SuperIO Configuration
IDE Configuration
Floppy Configuration
Boot Settings Configuration
Event Log Configuration
←→ Select Screen
↑↓ Select Item
Enter Go to Sub Screen
F1 General Help
F10 Save and Exit
ESC Exit
v02.01 (C) Copyright 1985-2000, American Megatrends Inc.

S2060 Tomcat i815e
33
Chapter 3
BIOS Configuration
Configure Nat366 Serial Port(s) and Parallel Port (Super I / O)

In this sub screen you can configure the different hardware ports available, and change
the status of the floppy controller.
Onboard Floppy This device handles communication betw een
Controller the floppy drive and the motherboard. [Default
is Enabled]
Serial Port Address The addresses of Serial Ports 1 and 2 can be
changed if a hardw are conflict occurs.
[Default is Disabled]
Serial Port 2 Mode Default is Norm al
Parallel Port Address The address and IRQ of the Parallel Port can
be changed if a hardw are conflict occurs.
The Parallel Port Mode relates to your printer’s
mode of communication (check your printer
documentation for details). [Default is
Disabled]
Parallel Port IRQ Default is 7
Parallel Port Mode Default is Norm al
Onboard MIDI Port* The address and IRQ of the Onboard MIDI Port
can be changed if a hardw are conflict
occurs. [Default is 330]
Onboard Gam e Port* The address of the game port can be changed
if a hardw are conflict occurs. [Default is
Enabled]
IDE Configuration
On bootup, the BIOS will auto-detect the existence of IDE devices such as hard drives
and CD-ROMs. You also can check the status of those IDE devices and change other
IDE-related options. There are also configuration sub screens for each IDE device
(denoted by the symbol).
Onboard PCI IDE Controller The PCI IDE Controller is essential for communication
betw een the IDE devices and the motherboard.
[Default is Both]
Hard Disk Protect This option disables or enables w rite protection to the
IDE devices. This option is only effective if the
devices are being accessed through the BIOS.
ATA(PI) Detect Tim e Out The BIOS w ill spend a preset amount of time to detect
any IDE devices before it continues to the next stage
of bootup. The amount of time can be changed using
this option. [Default is 0]
ATA(PI) 80Pin Cable Detection Selects the process that the BIOS w ill use to detect
80Pin ATA(PI) cables. [Default is Host & Device]
http://www.tyan.com
34
BIOS SETUP UTILITY
IDE Configuration DISABLED: disables the

integrated IDE
Onboard PCI IDE Controller [Enabled]
Controller.
PRIMARY: enables only
Primary IDE Master : [Hard Disk]
the Primary IDE
Primary IDE Slave : [Not Detected]
Controller.
Secondary IDE Master : [Not Detected]
SECONDARY: enables only
Secondary IDE Slave : [Not Detected]
the Secondary IDE
Controller.
Hard Disk Protect [Disabled]
BOTH: enables both IDE
ATA(PI) Detect Time Out [35]
Controllers
ATA(PI) 80Pin Cable Detection [Host & Device]
↑↓ Select Item
BIOS
F1 General Help
F10 Save and Exit
ESC Exit
When you enter one of the IDE configuration sub screens (by highlighting one of the
options preceded by a symbol, and pressing <ENTER>, example shown below),
you will be presented with a status on the IDE device, and a set of configuration
options for the IDE device (shown on the next page).
BIOS SETUP UTILITY
Primary IDE Master DISABLED: disables the

integrated IDE
Device : Hard Disk
Controller.
Vendor : IBM-DTLA-307075
PRIMARY: enables only
Size : 65.5 GB
the Primary IDE
LBA Mode : Supported
Controller.
Block Mode : 16 Sectors
SECONDARY: enables only
PIO Mode : 4
the Secondary IDE
Async DMA : MultiWord DMA-2
Controller.
Ultra DMA : Ultra DMA-2
BOTH: enables both IDE
S.M.A.R.T. : Supported
Controllers
Type [Auto]
LBA / Large Mode [Auto]
Block (Multi-Sector Transfer) [Auto]
PIO Mode [Auto]
DMA Mode [Auto] ←→ Select Screen
S.M.A.R.T. [Auto]
↑↓ Select Item
32Bit Data Transfer [Disabled]
F1 General Help
ARMD Emulation Type [Auto]
F10 Save and Exit
ESC Exit

* Indicates an optional feature not available on all Tomcat i815e models.
S2060 Tomcat i815e
35
Chapter 3
BIOS Configuration
Type The type of IDE device installed can be configured using this
option. [Default is Auto]
LBA/Large Mode These modes make it possible for the BIOS to take
advantage of the additional space on drives w hich are larger
than 504MB. This can be auto-detected (w hen you select
Auto for Type), or you can manually set this mode to
Disabled. [Default is Auto]
Block (Multi-Sector Transfer) When set to Auto, the Block mode auto-detects the optimal
number of block read / w rites per sector that the drive
supports. Default is Auto]
PIO Mode Programming Input / Output is a method of transmitting data
betw een devices that uses the system’s CPU as part of the
data path. There are 6 modes: 5 w ith their ow n transmission
speed and 1 auto mode. To use modes 3 and 4, you must
use an Enhanced IDE drive. [Default is Auto]
DMA Mode This option specifies the Direct Memory Access mode for the
IDE device. If set to Auto, the BIOS w ill determine the DMA
Mode. [Default is Auto]
S.M.A.R.T. (Self-Monitoring This option allow s the S.M.A.R.T. protocol to report server
Analysis and Reporting system information over a netw ork. [Default is Auto]
Technology)
32Bit Data Transfer If set to On, this options allow s for the transmission of 32-
bits in parallel (e.g. at the same time). If set to Off, only 16-
bits w ill be transmitted in parallel. [Default is Disabled]
ARMD Em ulation Type Specifies the type of emulation used for a non-disk device
attached as the primary master IDE device. If set to Auto, the
BIOS w ill determine the emulation type. [Default is Auto]
Floppy Configuration
In this configuration sub screen you can change options for your floppy drive(s).
Floppy A The settings are 360KB 5¼ inch, 1.2 MB 5¼ inch,
720KB 3½ inch, 1.44MB 3½ inch, or 2.88MB 3½ inch. If
you are not sure w hat type of floppy drive you have,
consult the documentation that came w ith your drive.
Floppy B The options are the same as listed for Floppy A.
Diskette Write Protect Sets w hether or not the drive can be w ritten to. [Default
is Disabled]
Floppy Drive Seek Sets w hether or not the BIOS should check for the
drive at bootup. [Default is Disabled]
http://www.tyan.com
36
Boot Settings Configuration
The Boot Settings Configuration sub screen several options are available to change how
the system boots up.
Quick Boot When Enabled, the BIOS w ill save time during bootup by
skipping certain items. [Default is Disabled]
Quiet Boot When Disabled, the normal POST messages are displayed.
AddOn ROM Display Specifies the system display mode that is set at the time that
Mode AMIBIOS POST initializes an optional ROM. If set to Force BIOS,
the current mode used by AMIBIOS is used. If set to Keep
Current, the current display mode is used. [Default is Force
BIOS]
Bootup Num -Lock Sets w hether or not the Num Lock key should be turned on at
bootup. [Default is On]
Bootup CPU Speed Sets the initial CPU speed to high or low at bootup. [Default is
BIOS
High]
PS / 2 Mouse Support Sets w hether or not the PS / 2 ports should support a mouse
device. If set to Enabled, IRQ12 w ill be reserved for the mouse
device. [Default is Enabled]
Typematic Rate Sets how fast the keyboard w ill accept input. [Default is Fast]
System Keyboard Sets w hether or not the keyboard exists. [Default is Present]
Primary Display Sets the type of monitor that is being used. [Default is VGA /
EGA]
Parity Check Sets w hether or not the memory w ill be checked for parity.
Boot to OS / 2 Set this option to Yes is you are using OS / 2 and using more
than 64MB of system memory. [Default is No]
Wait for ‘F1’ if error If an error occurs during bootup, the BIOS w ill ask the user to
press ‘F1’ to enter the BIOS Setup Utility to repair the problem.
[Default is Enabled]
Hit ‘DEL’ Message Display If Enabled, the BIOS w ill display an option to enter the BIOS
Setup Utility at bootup. [Default is Enabled]
Internal Cache Sets the type of caching algorithm that w ill be used for the L1
internal cache memory. [Default is Write-Back]
External Cache Sets the type of caching algorithm that w ill be used for the L2
external cache memory. [Default is Disabled]
S2060 Tomcat i815e
37
Chapter 3
BIOS Configuration
Event Log Configuration

The Event Log Configuration sub screen (shown below), the log of errors during
bootup can be viewed to help you troubleshoot any configuration problems you might
experience. The status of the Event Log is shown on the top half of the screen.
BIOS SETUP UTILITY
Event Log Configuration ENABLED: Allow logging

of events.
Event Log Area : Space Available
Event Log Data : Valid
Event Logging : [Enabled]

ECC Event Logging : [Disabled]
Clear All Event Logs : [No]
View Event Log

Mark All Events As Read
↑↓ Select Item
F1 General Help
F10 Save and Exit
ESC Exit
Event Logging If set to Enabled, events w ill be logged.

ECC Event Logging If set to Enabled, ECC events w ill be logged.
On the Tomcat i815e, ECC events are not
logged. [Default is Enabled]
Clear All Event Logs If set to Yes, the event log w ill be cleared.
[Default is No]
View Event Log Show s you the Event Log.
Mark All Events As Read By using this option, the events in the Event
Log can be organized to help troubleshoot
configuration problems.
http://www.tyan.com
38
Chipset Menu
The Chipset Setup is for advanced configuration of the motherboard attributes. There
are also two sub screens available (denoted by the symbol).
Processor Serial Num ber Identifies the CPU.
CPU Frequency Sets the ratio for the CPU frequency. [Default is 1:2]
CPU Latency Tim er Reserved for debugging. [Default is Disabled]
C000 - C4000, 16k Shadow Specifies how the 16k of Video ROM is treated at the
listed address.
Disabled: contents of video ROM are not copied to
RAM.
Enabled: contents of video ROM at listed address
segment is copied (shadow ed) from ROM to RAM for
faster execution.
BIOS
Cached / WP: contents of video ROM from listed
address segment are copied from ROM to RAM and
can be w ritten to or read from cache memory. [Default
is Cached/WP]
C800 - DC00, 16k shadow [Default is Cached/WP]
GMCH Configuration
The graphics chipset can be configured in the GMCH sub screen.
Prim ary Video Device Sets the primary device for video output. [Default is Auto]
Internal Graphics Mode Select Enables / disables the internal video device. [Default is
Enabled, 1MB]
Display Cache Window Size Specifies amount of cache available for the graphics local
memory w indow . [Default is 64MB]
Display VBIOS Message Enable / disable video BIOS message. [Default is Enabled]
Internal Graphics Scaling Sets scaling for internal video device. [Default is Auto]
Internal Graphics TV Form at Sets TV video standard (depends on your country
location). [Default is NTSC]
Output Device Sync / Non-sync Sets this depending on your video monitor. See your
monitor documentation for details. [Default is Non-
Synchronous]
Digital Device Priority Sets order of priority for video output devices. [Default is
CRT / FP / TV]
AGP Graphics Aperture Size Sets maximum memory aperture for onboard AGP port.
[Default is 64MB]
Init Display Cache Mem ory If enabled, the display cache w ill be initialized at time of
system boot. See the table on the next page for more
details. [Default is Enabled]
S2060 Tomcat i815e
39
Chapter 3
BIOS Configuration
System Mem ory Frequency Sets frequency of onboard DIMM memory. [Default is
Auto]
SDRAM Refresh Sets interval betw een Refresh signals to SDRAM. [Default
is Auto]
DRAM Cycle Tim e (SCLKs) Sets length of DRAM cycle time in SCLKs. [Default is Auto]
CAS Latency (SCLKs) Sets number of SCLKs betw een time w hen the Read
command is sampled by DRAM, and the Whitney Sample
reads data from SDRAM. [Default is Auto]
RAS# to CAS# Delay (SCLKs) Sets length of delay inserted betw een the RAS and CAS
signals of the DRAM system memory access cycle if
SDRAM is installed. [Default is Auto]
RAS# Precharge (SCLKs) Sets length of RAS precharge part of DRAM system
memory access cycle w hen SDRAM system memory is
installed. [Default is Auto]
DRAM Page Closing Policy Sets w hether DRAM pages should be closed after use, or
left open. [Default is Open]
Mem ory Hole Sets the location of an area of memory that cannot be
address on the ISA bus. [Default is Disabled]
If the Init Display Cache Memory is enabled, the following options will appear.
Paging Mode Control Enable / disable paging mode. [Default is Closed]

RAS-to-CAS Override Sets delay override. [Default is Disabled]
CAS Latency Sets number of SCLKs betw een the time w hen Read
command is sampled by DRAM and the Whitney Sample
reads data from SDRAM. [Default is Slow ]
RAS Tim ing Sets clock frequency for RAS and RC. [Default is Slow ]
RAS Pre-charge Sets clock frequency for RAS and RP. [Default is Slow ]
http://www.tyan.com
40
ICH Configuration
The interface chipset can be configured in the ICH sub screen.
Moon ISA Device Enable Enable / disable Moon ISA device. [Default is
Disabled]
ICH Positive Decode* Sets type of ICH decode used. [Default is Disabled]
CPU BIST Enable* Enable / disable CPU BIST. [Default is Disabled]
ICH DCB Enable* Enable / disable DCB. [Default is Disabled]
ICH Dev31 Func(3,5,6)Enable* Enable / disable ICH device listed. [Default is Enabled]
Sound Blaster Decode* Specifies address used for Sound Blaster devices.
Microsoft Sound Decode* Specifies address used for Microsoft Sound System
(MSS) devices. [Default is Disabled]
MIDI Decode Sets I / O address range for MIDI devices. [Default is
Disabled]
BIOS
Adlib Range 388h-35Bh* Allow s Adlib-compatible sound devices to use
address listed. [Default is Enabled]
Game Port (A, B)* Enable / disable Game Port listed. [Default is Enabled]
LPC 4Eh-4Fh Decode* Enable / disable LPC devices to use address range
listed. [Default is Enabled]
DMA-(0,1,2,3,5,6,7) Type* Specifies the bus that the specified DMA channel can
be used on. [Default is LPC DMA]
PCI / PnP Menu

In this sub screen you can configure the onboard PCI Plug-n-Play devices available.
BIOS SETUP UTILITY
Plug & Play O / S [No]

Reset Config Data [No]
PCI Latency Timer [64]
Allocate IRQ to PCI VGA [Yes]
Palette Snooping [Disabled]
PCI IDE BusMaster [Disabled]
OffBoard PCI / ISA IDE Card [Auto]
USB Function [Enabled]

Legacy USB Support [Auto]
IRQ3 [Available]
IRQ4 [Available]
IRQ5 [Available]
IRQ7 [Available]
IRQ9 [Available]
IRQ10 [Available] ←→ Select Screen
IRQ11 [Available] ↑↓ Select Item
IRQ14 [Available] F1 General Help
F10 Save and Exit
ESC Exit

S2060 Tomcat i815e
41
Chapter 3
BIOS Configuration
Plug & Play O / S Indicates if you are using a PnP O / S.

[Default is No]
Reset Config Data If set to Yes, PCI / PnP data w ill be stored in
Flash on next boot. [Default is No]
PCI Latency Tim er Specifies latency timings for PCI devices.
[Default is 64]
Allocate IRQ to PCI VGA Informs PCI devices that an ISA graphics
device is installed in the system so the card
w ill function correctly. [Default is Yes]
Palette Snooping If set to Enabled, multiple VGA devices
operating on different buses can handle data
from the CPU on each set of palette registers
on every video device. [Default is Disabled]
PCI IDE Bus Master Specifies that the IDE controller on the PCI
bus has bus mastering capability. [Default is
Disabled]
OffBoard PCI / ISA IDE Card Specifies if an offboard PCI or ISA IDE
controller card is installed. [Default is Auto]
USB Function Enables USB. [Default is Enabled]
Legacy USB Support Enables legacy USB device support. [Default
is Auto]
IRQ (3,4,5,7,9,10,11,14,15) Allow s listed IRQ to be used by PCI / PnP
devices. [Default is Available]
DMA Channel (0,1,3,5,7) Allow s listed DMA to be used by PCI / PnP
devices. [Default is Available]
Reserved Mem ory Size Specifies size of memory area reserved for
legacy ISA adapter cards. [Default is
Disabled]
http://www.tyan.com
42
Power Menu
In this sub screen you can configure how the BIOS handles power management. Note
that the screen shown below is has Power Management / APM enabled, which will
allow for more options to appear.
ACPI Aw are O / S Indicates w hether or not the O / S has pow er

management capabilities. [Default is Yes]
Repost Video on S3 Resume Sets w hether or not to repost the video on S3
pow er state (hibernation). [Default is Yes]
Pow er Management / APM Enable / disable pow er management functions.
Standby Tim e Out Sets time that system w ill w ait during inactivity
before the system w ill enter Standby mode. [Default
is Disabled]
Suspend Pow er Saving Type Set type of pow er saving mode for Suspend.
BIOS
[Default is S1]
Suspend Time Out Sets time that system w ill w ait in Standby before
the system w ill enter Suspend mode. [Default is
Disabled]
Pow er Button Mode Sets how pow er button mounted externally on the
case w ill be used.
On / Off: Pow er button turns system on / off.
Suspend: Pow er button places computer in
Suspend or Full On pow er mode. [Default is On /
Off]
After G3 Enable Enable / disable After G3 function. [Default is
Disabled]
Green PC Monitor Pow er State Sets pow er state for green PC-compliant monitor.
[Default is Suspend]
Video Pow er Dow n Mode Sets pow er state for video subsystem. [Default is
Suspend]
Hard Disk Pow er Dow n Mode Sets w hat pow er state hard disk w ill enter after
period of inactivity. [Default is Suspend]
Hard Disk Tim e Out (Minute) Sets time that system w ill w ait before hard disk
goes into pow er saving mode. [Default is Disabled]
Display Activity Sets event monitoring on video display. [Default is

Ignore]
Manual Throttle Ratio Sets speed at w hich the system clock runs in
Standby mode. Setting is expressed as a
percentage betw een normal speed and speed
w hen CPU is in pow er saving mode. [Default is
50%]
S2060 Tomcat i815e
43
Chapter 3
BIOS Configuration
THRM Throttle Ratio Adjusts THRM throttle ratio. [Default is 50%]

Intruder Sel Sets Intruder Sel [Default is SMI]
Therm al SMI Enable Enable / disable Thermal SMI. [Default is
Disabled]
PME SMI Enable Enable / disable PME SMI. [Default is
Disabled]
SW SMI Tim er Enable Enable / disable SW SMI. [Default is
Disabled]
TCO Logic SMI Enable Enable / disable TCO Logic SMI. [Default is
Disabled]
SLP SMI Enable Enable / disable SLP SMI. [Default is
Disabled]
RTC Resum e Enable / disable Real Time Clock resume.
AC97 Logic Resum e Enable / disable AC'97 Logic resume. [Default
is Disabled]
USB Controller Resume Enable / disable USB controller resume.
PME Resum e Enable / disable PME resume. [Default is
Disabled]
RI Resum e Enable / disable RI resume. [Default is
Disabled]
SMBUS Resum e Enable / disable System Management Bus
resume. [Default is Disabled]
Boot Menu
In this sub screen you can configure options set for each device during boot. The
options available will depend on what devices you have installed in your computer.
Boot Device Priority Sets the order of devices that the BIOS
w ill attempt to boot from.
Hard Disk Drives Show s the Hard Disk Drives available.
Rem oveable Drives Show s the Removeable Drives
ATAPI CDROM Drives Show s the CDROM drives available.
Security Menu
In this sub screen you can configure security options such as passwords and boot
sector virus protection.
The status of the Supervisor and User Passwords are shown at the top, and options
can be set through the rest of the configuration sub screen.
http://www.tyan.com
44
Change Supervisor Passw ord Install or change the passw ord
Change User Passw ord Install or change the passw ord
Clear User Passw ord Immediately clears the User passw ord
Boot Sector Virus Protection Protect against boot sector viruses.
If you decide to change the Supervisor or User Password, the following box will
appear.
Enter New Password:
BIOS
To set the password, enter a unique set of 6 letters and / or numbers.
Exit Menu
Before you exit the BIOS Setup a set of options will be presented to you.
Exit Saving Changes Save changes and exit setup

Exit Discarding Changes Do not save changes and exit setup
Load Optim al Defaults Load optimal settings
NOTE: May not w ork w ith all applications
Load Failsafe Defaults Load failsafe settings
NOTE: May not be the optimal configuration
Discard Changes Disregard all changes you made
S2060 Tomcat i815e
45
Chapter 4
System Resources
4 chapter
System Resources
Beep Codes
Fatal errors, which halt the boot process, are communicated through a series of audible
beeps. If AMIBIOS POST can initialize the system video display, it displays the error
message. Displayed error messages, in most cases, allow the system to continue to
boot. Displayed error messages are described on pages 48-49. See the top of the next
page for the beep code chart.
B eep s Error Message Description
1 Refresh Failure The memory refresh circuitry is faulty.
2 Parity Error Parity error in the base memory (the first 64 KB block) of memory.
3 Base 64 KB Memory Failure Memory failure in first 64 KB.
A memory failure in the first 64 KB of memory, or Timer 1 is not

4 Timer Not Operational
functioning.
5 Processor Error The CPU generated an error.
6 8042 - Gate A20 Failure Cannot switch to protected mode.
7 Processor Exception Interrupt Error The CPU on the CPU Card generated an exception interrupt.
The system video adapter is either missing or its memory is faulty. This is
8 Display Memory Read/Write Error
not a fatal error.
9 ROM Checksum Error The ROM checksum value does not match the value encoded in AMIBIOS.
10 CMOS Shutdown Register Read/Write Error The shutdown register for CMOS RAM has failed.
The cache memory test failed. Cache memory is disabled. Do not press
11 Cache Memory Bad — Do Not Enable Cache
<Ctrl> <Alt> <Shift> <+> to enable cache memory.
http://www.tyan.com
46
Troubleshooting System Problems
If the computer beeps... then...

1, 2, or 3 times... reseat the memory DIMMs or DIPs.
If the system still beeps, replace the
memory.
6 times... try a different keyboard, or replace the
keyboard fuse, if there is one. If the error
occurs again, return the board to your dealer
for a replacement.
8 times... there is a memory error on the video
adapter. Replace the video adapter, or
the RAM on the video adapter (applies only to
external video adapters). If the error occurs
again, return the board to your dealer for a
replacement.
9 times... the BIOS ROM chip is bad. The
system probably needs a new BIOS
ROM chip.
11 times... reseat the cache memory on the
SYSTEM
motherboard. If it still beeps, replace
the cache memory.
4, 5, 7, or 10 times... for 5 or 7 beeps, first test with a new CPU - if that
does not solve the problem, then motherboard must
be replaced.
S2060 Tomcat i815e
47
Chapter 4
System Resources
Displayed Error Messages
If an error occurs after the system display has been initialized, the error message will
be displayed as follows:
ERROR Message Line 1

ERROR Message Line 2
Press <F1> to continue
and the system will halt. The system will not halt if the Wait for <F1> If Any Error
option in Advanced Setup is Disabled.
RUN SETUP UTILITY
may also appear. Press <F1> to run WINBIOS Setup if this message appears.
Error Message Explanation
8042 Gate-A20 Error Gate A20 on the keyboard controller (8042) i s not worki ng. Replace the 8042.
Address Li ne Short! Error i n the address decodi ng ci rcui try.
No response from dri ve C :. Run the AMID i ag Hard D i sk Uti li ty. C heck the C : hard
C : D ri ve Error
di sk type i n Standard Setup.
C : D ri ve Fai lure No response from hard di sk dri ve C :. Replace the dri ve.
C ache Memory Bad,

C ache memory i s defecti ve. Run AMID i ag.
D o Not Enable C ache!
C H-2 Ti mer Error An AT system has two ti mers. There i s an error i n ti mer 2.
C MOS Battery State

C MOS RAM i s powered by a battery. The battery power i s low. Replace the battery.
Low
C MOS C hecksum
C MOS RAM checksum i s di fferent than the previ ous value. Run WINBIOS Setup.
Fai lure
C MOS System Opti ons

The values stored i n C MOS RAM have been destroyed. Run WINBIOS Setup.
Not Set
C MOS D i splay Type The vi deo type i n C MOS RAM does not match the type detected. Run WINBIOS
Mi smatch Setup.
C MOS Memory Si ze The amount of memory found by AMIBIOS i s di fferent than the amount i n C MOS
Mi smatch RAM. Run WINBIOS Setup.
C MOS Ti me and D ate

Run Standard Setup to set the date and ti me.
Not Set
No response from dri ve D :. Run the AMID i ag Hard D i sk Uti li ty. C heck the hard di sk
D : D ri ve Error
type i n Standard Setup.
http://www.tyan.com
48
Chapter 4
System Resources
Error Message Explanation
D: drive failure No response from hard disk drive D:. Replace the drive.
The boot diskette in drive A: cannot be used to boot the system. Use
Diskette Boot Failure
another boot diskette and follow the screen instructions.
Display Switch Not Some systems require a video switch be set to either color or
Proper monochrome. Turn the system off, set the switch properly, then power on.
DMA Error Error in the DMA controller.
DMA 1 Error Error in the first DMA channel.
DMA 2 Error Error in the second DMA channel.
AMIBIOS cannot communicate with the floppy disk drive controller. Check
FDD Controller Failure
all appropriate connections after the system is powered down.
AMIBIOS cannot communicate with the hard disk drive controller. Check
HDD Controller Failure
all appropriate connections after the system is powered down.
INTR1 Error Interrupt channel 1 failed POST.
INTR2 Error Interrupt channel 2 failed POST.
SYSTEM
AMIBIOS can read the diskette in floppy drive A:, but it cannot boot the
Invalid Boot Diskette system with it. Use another boot diskette and follow the screen
instructions.
Keyboard Is The keyboard lock on the system is engaged. The system must be
Locked...Unlock It unlocked to continue to boot.
The keyboard has a timing problem. Make sure a Keyboard Controller

Keyboard Error AMIBIOS is installed. Set Keyboard in Advanced Setup to Not Installed to
skip the keyboard POST routines.
KB/Interface Error There is an error in the keyboard connector.
Cannot find a proper bootable sector on either drive A: or C:. AMIBIOS

No ROM BASIC
cannot find ROM Basic.
Parity error in memory installed on an adapter card in an expansion slot.

The format is:
Off Board Parity Error OFF BOARD PARITY ERROR ADDR = (XXXX)
XXXX is the hex address where the error occurred. Run AMIDiag to find
and correct memory problems.
Parity error in motherboard memory. The format is:

ON BOARD PARITY ERROR ADDR = (XXXX)
On Board Parity Error
XXXX is the hex address where the error occurred. Run AMIDiag to find
and correct memory problems.
Parity error in system memory at an unknown address. Run AMIDiag to

Parity Error ????
find and correct memory problems.
S2060 Tomcat i815e
49
Flash Utility
Note: You need to download the Flash Utility from the Tyan web site at:
http://www.tyan.com
1. If you want to flash BIOS without updating the boot block, do this:
Boot to DOS, and type “flash4mb” followed by the BIOS file

name.
Example: FLASH4MB BIOSFILE.ROM
2. If you want to flash BIOS with boot block update, do this:
i. Shutdown system, close JP2 to disable the boot block

protection. Then boot system to DOS.
ii. Type "flash4mb" followed by <Enter> key.
iii. To save or not save the old BIOS by you choice.
iv. Type in the BIOS file name, like "BIOSFILE.ROM”.
v. Flash utility will auto-complete the flash, include boot block
at this point.
vi. Shutdown the system, open jumper JP2 again. Then restart
the system.
For more information and updates about the Flash Utilities, check the Tyan web site
at: http://www.tyan.com
! NOTE: Please be aware that by flashing your BIOS, you agree that in the event
of a BIOS flash failure, you must contact your dealer for a replacement BIOS.
important!
There are no exceptions. Tyan does not have a policy of replacing BIOS chips
directly with end users. In no event will Tyan be held responsible for damage
done to the BIOS by the end user.
http://www.tyan.com
50
S2060 Tomcat i815e
51
Appendix
Glossary
Appendix
Glossary
ACPI (Advanced Configuration and Power Interface) is a power management specifica-
tion that allows the operating system to control the amount of power distributed to the
computer’s devices. Devices not in use can be turned off, reducing unnecessary power
expenditure.
AGP (Accelerated Graphics Port) is a PCI-based interface which was designed

specifically for demands of 3D graphics applications. The 32-bit AGP channel directly
links the graphics controller to the main memory. While the channel runs at only
66MHz, it supports data transmission during both the rising and falling ends of the
clock cycle, yielding an effective speed of 133MHz.
AIMM (AGP Inline Memory Module) is intended to provide 4MB of addressable

SDRAM (arranged as 1Mx32), which resides on a module in a 3.3V or universal AGP
slot.
AMR (Audio Modem Riser) is a modem that can be used on Intel Reference
Motherboard platforms using Intel’s core logic chipsets supporting AC-Link 2.1 It
supports fax and all data feeback modes. It provides high speed communicstions
between your perosnal computer and a remote location, such as an Internet Service
Provider (ISP).
AT was the original form factor of IBM’s PC.
ATAPI (AT Attachment Packet Interface), also known as IDE or ATA, is a drive
implementation that includes the disk controller on the device itself. It allows CD-
ROMs and tape drives to be configured as master or slave devices, just like hard drives.
http://www.tyan.com
52
ATX form factor was designed to replace the AT form factor. It improves on the AT
design by rotating the board ninety degrees, so that the IDE connectors are closer to
the drive bays, and the CPU is closer to the power supply and cooling fan. The
keyboard, mouse, serial, USB, and parallel ports are built in.
Bandwidth refers to carrying capacity. The greater the bandwidth, the more data the
bus, phone line, or other electrical path, can carry. Greater bandwidth, then, also results
in greater speed.
A BBS (Bulletin Board System) is a computer system with a number of modems

hooked up to it which acts as a center for users to post messages and access informa-
tion.
The BIOS (Basic Input/Output System) program resides in the ROM chip, and
provides the basic instructions for controlling your computer’s hardware. Both the
operating system and application software use BIOS routines to ensure compatibility.
A buffer is a portion of RAM which is used to temporarily store data, usually from an
application, though it is also used when printing, and in most keyboard drivers. The
CPU can manipulate data in a buffer before copying it, all at once, to a disk drive.
While this improves system performance--reading to or writing from a disk drive a
single time is much faster than doing so repeatedly--there is the possibility of losing
your data should the system crash. Information stored in a buffer is temporarily
stored, not permanently saved.
A bus is a data pathway. The term is used especially to refer to the connection
between the processor and system memory, and between the processor and PCI or ISA
local buses.
Bus mastering allows peripheral devices and IDEs to access the system memory
GLOSSARY
without going through the CPU (similar to DMA channels).
A cache is a temporary storage area for data that will be needed often by an applica-
tion. Using a cache lowers data access times, since the needed information is stored in
the SRAM instead of in the slower DRAM. Note that the cache is also much smaller
than your regular memory: a typical cache size is 512KB, while you may have as much
as 1GB of regular memory.
Cache size refers to the physical size of the cache onboard. This should not be
confused with the cacheable area, which is the total amount of memory which can be
scanned by the system in search of data to put into the cache. A typical setup would
be a cache size of 512KB, and a cacheable area of 512MB. In this case, up to 512MB
of the main memory onboard is capable of being cached. However, only 512KB of this
memory will be in the cache at any given moment. Any main memory above 512MB
could never be cached.
Closed and open jumpers Jumpers and jumper pins are active when they are On or
Closed, and inactive when they are Off or Open.
S2060 Tomcat i815e
53
Appendix
Glossary
CMOS Complementary Metal-Oxide Semiconductors are chips that hold the basic
start-up information for the BIOS.
Communication and Networking Riser (CNR) provides interfaces to support

multichannel audio, V.90 analog modem, telephone line-based home networking, and 10/
100 Ethernet-based networking, as well as expandability for future technologies.
The COM port is another name for the serial port, which is so-called because it
transmits the eight bits of a byte of data along one wire, and receives data on another
single wire (that is, the data is transmitted in serial form, one bit after another). Parallel
ports transmit the bits of a byte on eight different wires at the same time (that is, in
parallel form, eight bits at the same time).
DIMM (Dual In-line Memory Modules) are a faster and more capacious form of RAM
than SIMMs, and do not need to be installed in pairs.
DIMM bank DIMM banks are sometimes called DIMM sockets, because the physical
slot and the logical unit are the same. That is, one DIMM module fits into one DIMM
socket, which is capable of acting as a memory bank.
DMA (Direct Memory Access) channels are similar to IRQs. DMA channels allow
hardware devices (like sound cards or keyboards) to access the main memory without
involving the CPU. This frees up CPU resources for other tasks. As with IRQs, it is
vital that you do not double up devices on a single line. Plug and Play devices will take
care of this for you.
In Doze mode, only the CPU’s speed is slowed.
DRAM Dynamic RAM is a widely available, very affordable form of RAM which has
the unfortunate tendency to lose data if it is not recharged regularly (every few
milliseconds). This refresh requirement makes DRAM three to ten times slower than
non-recharged RAM such as SRAM.
EDO RAM (Extended Data-Out RAM) speeds access to memory locations by

assuming that memory addresses are static: the next time it looks for a bit of data, it
will be at the same spot, or one nearby.
EEPROM Electrically Erasable Programmable ROM, also called Flash BIOS, is a

ROM chip which can, unlike normal ROM, be updated. This allows you to keep up
with changes in the BIOS programs without having to buy a new chip. TYAN’s BIOS
updates can be found at: http://www.tyan.com/html/drivers.html
ESCD (Extended System Configuration Data) is a format for storing information

about Plug and Play devices in the system BIOS. This information helps properly
configure the system each time it boots.
Firmware is low level software that controls the system hardware.
http://www.tyan.com
54
Form factor is an industry term for the size, shape, power supply type, and external
connector type of the PCB (personal computer board) or motherboard. The standard
form factors are the AT and ATX, although TYAN also makes some Baby-AT boards.
AGlobal timer is an onboard hardware timer, such as the Real Time Clock.
Handshaking is a form of encryption. One system, typically the server, sends an
encryption scheme to another agent, typically a client. Thus, the client’s data is
protected during transmittal to the server.
HDD stands for Hard Disk Drive.
H-SYNC controls the horizontal properties of the monitor.
IC (Integrated Circuit) is the formal name for the computer chip.

IDE Integrated Device (or Drive) Electronics is a simple, self-contained hard drive
interface. It can handle drives up to 8.4GB in size. Almost all IDEs sold now are in fact
Enhanced IDEs (EIDEs).
IDE INT (IDE Interrupt) is a hardware interrupt signal that goes to the IDE.
I/O (Input/Output) is the connection between your computer and another piece of
hardware (mouse, keyboard, etc.).
IRQ An Interrupt Request is an electronic request that runs from a hardware device to
the CPU. The interrupt controller assigns priorities to incoming requests and delivers
them to the CPU. It is important that there is only one device hooked up to each IRQ
line; doubling up devices on IRQ lines can lock up your system. Happily, Plug and
Play operating systems take care of these details for you.
ISA (Industry Standard Architecture) is a slower 8- or 16-bit bus (data pathway).
Latency is the amount of time that one part of a system spends waiting for another GLOSSARY
part to catch up. This is most common when the system sends data out to a peripheral
device, and is waiting for the peripheral to send some data back (peripherals tend to be
slower than onboard system components).
NVRAM ROM and EEPROM are both examples of Non-Volatile RAM, memory that
holds its data without power. DRAM, in contrast, is volatile.
OEMs (Original Equipment Manufacturers) like Compaq or IBM package other

companies’ motherboards and hardware inside their case and sell them.
The parallel port transmits the bits of a byte on eight different wires at the same time
(that is, in parallel form, eight bits at the same time).
PCI (Peripheral Component Interconnect) is a 32-bit local bus (data pathway) which
is faster than the ISA bus. Local buses are those which operate within a single system
(as opposed to a network bus, which connects multiple systems).
S2060 Tomcat i815e
55
Appendix
Glossary
PCI PIO (PCI Programmable Input/Output) modes are the data transfer modes used
by IDE drives. These modes use the CPU for data transfer (DMA channels do not).
PCI refers to the type of bus used by these modes to communicate with the CPU.
PCI-to-PCI bridge allows you to connect multiple PCI devices onto one PCI slot.
Pipeline burst SRAM is a fast secondary cache. It is used as a secondary cache

because SRAM is slower than SDRAM, but usually larger. Data is cached first to the
faster primary cache, and then, when the primary cache is full, to the slower secondary
cache.
Pipelining improves system performance by allowing the CPU to begin executing a

second instruction before the first is completed. A pipeline can be likened to an
assembly line, with a given part of the pipeline repeatedly executing a set part of an
operation on a series of instructions.
PM timers (Power Management timers) are software timers that count down the
number of seconds or minutes until the system times out and enters sleep, suspend, or
doze mode.
PnP is an acronym for Plug and Play, a design standard that has become ascendant in
the industry. Plug and Play devices require little set-up to use. Novice end users can
simply plug them into a computer that is running on a Plug and Play-aware operating
system (such as Windows 98), and go to work. Devices and operating systems that are
not Plug and Play require you to reconfigure your system each time you add or change
any part of your hardware.
The term RAM (Random Access Memory), while technically referring to a type of
memory where any byte can be accessed without touching the adjacent data, is often
used to refer to the system’s main memory. This memory is available to any program
running on the computer.
ROM (Read-Only Memory) is a storage chip which contains the BIOS, the basic
instructions required to boot the computer and start up the operating system.
SDRAM (Synchronous Dynamic RAM) is so-called because it can keep two sets of
memory addresses open simultaneously. By transferring data alternately from one set
of addresses, and then the other, SDRAM cuts down on the delays associated with
non-synchronous RAM, which must close one address bank before opening the next.
The serial port is so called because it transmits the eight bits of a byte of data along
one wire, and receives data on another single wire (that is, the data is transmitted in
serial form, one bit after another).
SIMM (Single In-line Memory Modules) are the most common form of RAM. They
must be installed in pairs, and do not have the carrying capacity or the speed of
DIMMs.
http://www.tyan.com
56
SIMM bank / socket SIMM sockets are the physical slots into which you stick
SIMM modules. A pair of SIMM sockets form a SIMM bank, and act as a unit. If
only one socket is filled, the bank will not operate.
In Sleep / Suspend mode, all devices except the CPU shut down.
SRAM (Static RAM), unlike DRAM, does not need to be refreshed in order to
prevent data loss. Thus, it is faster, and more expensive.
In Standby mode, the video and fixed disk drive shut down; all other devices operate
normally.
UltraDMA 33 / 66 / 100 is a fast version of the old DMA channel. UltraDMA is also
called UltraATA. Without UltraDMA your system cannot take advantage of the higher
data transmission rates of the new UltraATA hard drives.
USB (Universal Serial Bus) is a versatile port type that can function as a serial,
parallel, mouse, keyboard, or joystick port. It is fast enough to support video transfer,
and is capable of supporting up to 127 daisy-chained peripheral devices.
VGA (Video Graphics Array) is the PC video display standard.
V-SYNC controls the vertical properties of the monitor.
ZIF (Zero Insertion Force) sockets make it possible to insert CPUs without damaging
the sensitive pins. The CPU is lightly placed in an open ZIF socket, and the metal
lever pulled down. This shifts the processor over and down, guiding it into place on the
GLOSSARY
board.
S2060 Tomcat i815e
57
Notice for the USA
Compliance Information Statement (Declaration of Conformity Procedure) DoC
FCC Part 15: This Device complies with Part 15 of the FCC Rules.
Operation is subject to the following conditions:
1) this device may not cause harmful interference, and
2) this device must accept any interference received including interference that may
cause undesired operation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try one or more of the following measures:
· Reorient or relocate the receiving antenna.
· Increase the separation between the equipment and receiver.
· Plug the equipment into an outlet on a circuit different from
that of the receiver.
· Consult the dealer or an experienced radio/television
technician for help.
Notice for Canada

This apparatus complies with the Class B limits for radio interference as specified in
the Canadian Department of Communications Radio Interference Regulations. (Cet
appareil est conforme aux normes de Classe B d’ interference radio tel que spécifié par
le Ministére Canadien des Communications dans les réglements d’interférence radio.)
Notice for Europe (CE Mark)

This product is in conformity with the Council Directive 89/336/EEC, 92/31/EEC
(EMC).
CAUTION: Lithium Batteries included with this board. Danger of explosion if battery
is incorrectly replaced. Replace only with the same or equivalent type recommended
by manufacturer. Dispose of used batteries according to manufacturer instructions and
your local county regulations.
Note: The joystick port (optional) maximum output rating is 9 amperes at 5 volts.
Document # D1419-101
http://www.tyan.com
58

Tomcat I815e: Tyan S2060

Uploaded by

Document Informationclick to expand document information

Document Informationclick to expand document information

Copyright:

Available Formats

Tomcat I815e: Tyan S2060

Uploaded by

Document Information

Original Title

Copyright

Available Formats

Share this document

Share or Embed Document

Sharing Options

Did you find this document useful?

Is this content inappropriate?

Copyright:

Available Formats

Tomcat I815e: Tyan S2060

Uploaded by

Copyright:

Available Formats

Tyan S2060

Tomcat i815e S2060 is a trademark of Tyan Computer Corporation.

* Indicates an optional feature available on some models of Tomcat i815e.

Remember to take a look at Tyan’s web site located at

This icon alerts you to particularly important details regarding the

1. Wherever possible, we have included step-by-step instructions for

While we have alerted you to potential dangers in several places in

S2060 Tomcat i815e

Expansion Slots •One 2x / 4x mode 3.3V / 1.5V AGP slot

Chipset Information •Intel® i815e AGPset

Hardware Monitoring •National PC87366 hardware monitoring chip

Memory*** •Three 3.3V 168-pin DIMM sockets

Integrated PCI IDE •Dual channel master mode

Integrated I/O •One Floppy connector for up to two drives

*** See Tyan website for Memory Compatibility details: http://www.tyan.com

Integrated 2D/3D Graphics •Intel i815e D.V.M. Technology graphics core

Integrated Audio •Software audio codec

BIOS •AMI BIOS 4 Mbit Flash

Form Factor •ATX 2.03 (12” x 8”)

Regulatory •FCC Class B (Declaration of Conformity)

* See Tyan website for CPU Compatibility List:

S2060 Tomcat i815e

Returning Merchandise for Service

For Resellers Only:

This page left blank intentionally.

S2060 Tomcat i815e

How to install our products right... the first time.

(1) Ground yourself properly before removing your motherboard

! DO NOT APPLY POWER TO THE BOARD IF IT HAS BEEN DAMAGED!

S2060 Tomcat i815e

Quick References for Jumpers

Figure 2-1 Figure 2-2

2 pin jumpers 3 (or more) pin jumpers

off on 1-2 2-3 open

Intel® PGA 370 FSB 66/100/133 MHz

LPT1 Printer Port

Audio Codec* J29* J37*

Super I/O J12

* Indicates an optional feature available on some models of Tomcat i815e.

S2060 Tomcat i815e

Map of Tomcat i815e Features

6 PCI slots AGP National hardware AMI

1-A. J15 External Pin Assignments

VCC+ 1 2 Power LED+

Ground 5 6 Power On/Off

Switch 7 8 Pwr On/Off GND

IR GND 13 14 NO CONNECT J15,

JP1 (clear CMOS) JP2

1-C. Clear CMOS and Reset Password (JP1)

1-D. BIOS Flash TL (JP2)

1-E. Wake-On Ring Connector (optional) (J34)

1-F. Wake-On LAN Connector (optional) (J8)

1-G. Chassis Intrusion Alarm Connector (J7)

1-H. Fan Connectors (FAN1,FAN2,FAN3,FAN4)

1-I. External Speaker Connector (J13)

1-M. LAN EEPROM Enable/Disable (optional) (J38)

1-O. External HDD LED (J12)