OMKK54136
OMKK54136
OMKK54136
OPERATOR'S MANUAL
*omkk54136*
Product View
P6773—UN—22FEB01
975 Integral Rev. In Furrow Moldboard Plow
PX07220,0000B5C-19-28JUL16
PX03972,0001381-19-07MAR18
Introduction
RXA0150915—UN—01FEB16
PX03972,0001372-19-19JAN18
Introduction
APY05801—UN—11MAY18
975 In-Furrow Reversible Plow
W28329—UN—18OCT17
CN80434,0000864-19-10MAY18
Contents
Page Page
i
Contents
Page
Attachments
Gauge Wheel Installation . .. .. .. .. ... .. .. .. .. .. .. ... .. 45-1
Troubleshooting
Troubleshooting . .. .. .. ... .. .. .. .. .. ... .. .. .. .. .. .. ... .. 50-1
Troubleshooting . .. .. .. ... .. .. .. .. .. ... .. .. .. .. .. .. ... .. 50-2
Troubleshooting . .. .. .. ... .. .. .. .. .. ... .. .. .. .. .. .. ... .. 50-2
Service
Bottoms . ... .. .. .. .. .. .. ... .. .. .. .. .. ... .. .. .. .. .. .. ... .. 60-1
Tension Bolt . .. .. .. .. .. ... .. .. .. .. .. ... .. .. .. .. .. .. ... .. 60-1
Landside ... .. .. .. .. .. .. ... .. .. .. .. .. ... .. .. .. .. .. .. ... .. 60-2
Service at the Beginning of the Season . .. .. .. ... .. 60-2
Wheel Bearings . .. .. .. ... .. .. .. .. .. ... .. .. .. .. .. .. ... .. 60-3
Reversing Mechanism .. .. .. .. .. .. ... .. .. .. .. .. .. ... .. 60-3
Verification . .. .. .. .. .. .. ... .. .. .. .. .. ... .. .. .. .. .. .. ... .. 60-3
Adjusting Selective Control Valve Flow Rate
(Flow Control Setting) .. .. .. .. .. ... .. .. .. .. .. .. ... .. 60-3
Adjusting Selective Control Valve Flow Rate
(Flow Control Setting) .. .. .. .. .. ... .. .. .. .. .. .. ... .. 60-4
Unified Inch Bolt and Screw Torque Values . .. ... .. 60-4
Metric Bolt and Screw Torque Values .. .. .. .. .. ... .. 60-5
Storage
Keep Your Plow Prepared .. .. .. .. ... .. .. .. .. .. .. ... .. 65-1
Removing the Plow From Storage . .. .. .. .. .. .. ... .. 65-1
Specifications
Specifications . .. .. .. .. ... .. .. .. .. .. ... .. .. .. .. .. .. ... .. 70-1
Specifications . .. .. .. .. ... .. .. .. .. .. ... .. .. .. .. .. .. ... .. 70-1
Specifications . .. .. .. .. ... .. .. .. .. .. ... .. .. .. .. .. .. ... .. 70-1
Product Identification Number . .. ... .. .. .. .. .. .. ... .. 70-1
ii
Safety
Recognize Safety Information Follow Safety Instructions
T81389—UN—28JUN13 TS201—UN—15APR13
This is a safety-alert symbol. When you see this symbol Carefully read all safety messages in this manual and on
on your machine or in this manual, be alert to the your machine safety signs. Keep safety signs in good
potential for personal injury. condition. Replace missing or damaged safety signs. Be
sure new equipment components and repair parts
Follow recommended precautions and safe operating include the current safety signs. Replacement safety
practices. signs are available from your John Deere dealer.
DX,ALERT-19-29SEP98
There can be additional safety information contained on
parts and components sourced from suppliers that is not
reproduced in this operator's manual.
Understand Signal Words
Learn how to operate the machine and how to use
controls properly. Do not let anyone operate without
instruction.
Keep your machine in proper working condition.
Unauthorized modifications to the machine may impair
the function and/or safety and affect machine life.
If you do not understand any part of this manual and
need assistance, contact your John Deere dealer.
DX,READ-19-16JUN09
TS187—19—30SEP88
General Safely Rules
DANGER; The signal word DANGER indicates a 1. To avoid injury, always be careful while operating a
hazardous situation which, if not avoided, will result in tractor and plow.
death or serious injury. 2. For tractor stability and operator safety, tractor front
WARNING; The signal word WARNING indicates a end weights are required.
hazardous situation which, if not avoided, could result in 3. Always lower the plow to the ground when not in
death or serious injury. use.
CAUTION; The signal word CAUTION indicates a 4. Always positioning the standards frame at center
hazardous situation which, if not avoided, could result in before unhitching from the tractor.
minor or moderate injury. CAUTION may also be used to
alert against unsafe practices associated with events 5. Unauthorized modifications to the machine may
which could lead to personal injury. impair the function and/or safety and affect machine
life.
A signal word—DANGER, WARNING, or CAUTION—is
used with the safety-alert symbol. DANGER identifies 6. Always park plow on flat level ground.
the most serious hazards. DANGER or WARNING
7. Do not grease, oil, or adjust the plow while it is in
safety signs are located near specific hazards. General
motion.
precautions are listed on CAUTION safety signs.
CAUTION also calls attention to safety messages in this 8. Drive slowly through gates and doors.
manual.
9. Avoid traveling over loose field, rocks and holes.
DX,SIGNAL-19-05OCT16
05-1
Safety
10. To avoid accidents, be sure no one is near plow Avoid High-Pressure Fluids
when reversing.
PX07220,0000B66-19-28JUL16
X9811—UN—23AUG88
Inspect hydraulic hoses periodically – at least once per
year – for leakage, kinking, cuts, cracks, abrasion,
blisters, corrosion, exposed wire braid or any other signs
of wear or damage.
Replace worn or damaged hose assemblies
TS206—UN—15APR13 immediately with John Deere approved replacement
Wear close fitting clothing and safety equipment parts.
appropriate to the job.
Escaping fluid under pressure can penetrate the skin
Operating equipment safely requires the full attention of causing serious injury.
the operator. Do not wear radio or music headphones
while operating machine. Avoid the hazard by relieving pressure before
disconnecting hydraulic or other lines. Tighten all
DX,WEAR2-19-03MAR93
connections before applying pressure.
Search for leaks with a piece of cardboard. Protect
hands and body from high-pressure fluids.
Prepare for Emergencies
If an accident occurs, see a doctor immediately. Any
fluid injected into the skin must be surgically removed
within a few hours or gangrene may result. Doctors
unfamiliar with this type of injury should reference a
knowledgeable medical source. Such information is
available in English from Deere & Company Medical
Department in Moline, Illinois, U.S.A., by calling 1-800-
822-8262 or +1 309-748-5636.
DX,FLUID-19-12OCT11
TS290—UN—23AUG88
Only allow the operator on the machine. Keep riders off.
Riders on machine are subject to injury such as being
05-2
Safety
struck by foreign objects and being thrown off of the Safe Transport of the Disk Plow
machine. Riders also obstruct the operator’s view
resulting in the machine being operated in an unsafe
manner.
DX,RIDER-19-03MAR93
TS205—UN—23AUG88
To obtain machine clearance during transport, do use a
tractor with rear tires smaller than 18.4 X 38”.
Never exceed 30 km/h (18 mph) when transporting the
Moldboard Plow.
Specification
Moldboard Plow—Maximum
TS1729—UN—24MAY13
speed. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30 km/h
Avoid crushing injury or death during rollover. (18 mph)
Reduce speed when traveling over uneven ground.
This machine is equipped with a rollover protective
structure (ROPS). USE a seat belt when you operate Always travel at a speed that allows adequate control of
with a ROPS. steering and braking.
● Hold the latch and pull the seat belt across the body. Plow must be transported with the bottom frame in
● Insert the latch into the buckle. Listen for a click. centered position. Be aware of height and width
restrictions which avoid collision with overpasses or
● Tug on the seat belt latch to make sure that the belt is
other road users.
securely fastened.
VG41678,0000074-19-18JAN18
● Snug the seat belt across the hips.
TS951—UN—12APR90
Prevent collisions between other road users, slow
moving tractors with attachments or towed equipment,
and self-propelled machines on public roads. Frequently
05-3
Safety
check for traffic from the rear, especially in turns, and cable (-) before making adjustments on electrical
use turn signal lights. systems or welding on machine.
Use headlights, flashing warning lights, and turn signals On towed implements, disconnect wiring harnesses
day and night. Follow local regulations for equipment from tractor before servicing electrical system
lighting and marking. Keep lighting and marking visible, components or welding on machine.
clean, and in good working order. Replace or repair
Falling while cleaning or working at height can cause
lighting and marking that has been damaged or lost. An
serious injury. Use a ladder or platform to easily reach
implement safety lighting kit is available from your John
each location. Use sturdy and secure footholds and
Deere dealer.
handholds.
DX,FLASH-19-07JUL99
DX,SERV-19-28FEB17
X9811—UN—23AUG88
Hydraulic hoses can fail due to physical damage, kinks,
age, and exposure. Check hoses regularly. Replace
damaged hoses.
Escaping fluid under pressure can penetrate skin
causing serious injury. Search for leaks with a piece of
cardboard. Protect hands and body from high-pressure
fluids.
If an accident occurs, see a doctor immediately. Any
fluid injected into skin must be surgically removed within
a few hours or gangrene can result. Doctors unfamiliar
with this type of injury should reference a knowledgeable
medical source. Such information is available from
Deere and Company Medical Department in Moline,
TS218—UN—23AUG88 Illinois, U.S.A.
Understand service procedure before doing work. Keep
NXN,9930,HYD-19-29NOV16
area clean and dry.
Never lubricate, service, or adjust machine while it is
moving. Keep hands, feet, and clothing away from
power-driven parts. Disengage all power and operate
controls to relieve pressure. Lower equipment to the
ground. Stop the engine. Remove the key. Allow
machine to cool.
Securely support any machine elements that must be
raised for service work.
Keep all parts in good condition and properly installed.
Fix damage immediately. Replace worn or broken parts.
Remove any buildup of grease, oil, or debris.
On self-propelled equipment, disconnect battery ground
05-4
Safety
Use Seat Belt Properly ● Remove paint a minimum of 100 mm (4 in.) from area
to be affected by heating. If paint cannot be removed,
wear an approved respirator before heating or
welding.
● If you sand or grind paint, avoid breathing the dust.
Wear an approved respirator.
● If you use solvent or paint stripper, remove stripper
with soap and water before welding. Remove solvent
or paint stripper containers and other flammable
material from area. Allow fumes to disperse at least
15 minutes before welding or heating.
Remove Paint Before Welding or Heating Stay clear of moldboard during field operation.
Stay clear of rest path if standards hang in partially
tripped position from obstruction or during maintenance.
Always lower plow to ground when not in use.
Always use support stands (if equipped) to support plow
before unhitching from tractor.
Use required front-end weights for optimum tractor
stability. (See Determining Front Ballast and Implement
Code Table in Preparing the Tractor Section.)
PG57337,0000278-19-18JAN18
TS220—UN—15APR13
Avoid potentially toxic fumes and dust.
Hazardous fumes can be generated when paint is
heated by welding, soldering, or using a torch.
Remove paint before heating:
05-5
Safety
TS211—UN—15APR13
Explosive separation of a tire and rim parts can cause
serious injury or death.
Do not attempt to mount a tire unless you have the
proper equipment and experience to perform the job.
Always maintain the correct tire pressure. Do not inflate
the tires above the recommended pressure. Never weld
or heat a wheel and tire assembly. The heat can cause
an increase in air pressure resulting in a tire explosion.
Welding can structurally weaken or deform the wheel.
When inflating tires, use a clip-on chuck and extension
hose long enough to allow you to stand to one side and
NOT in front of or over the tire assembly. Use a safety
cage if available.
Check wheels for low pressure, cuts, bubbles, damaged
rims or missing lug bolts and nuts.
DX,RIM-19-24AUG90
05-6
Safety Signs
Read Safety Signs Carefully Hydraulic Cylinder
Carefully read and follow all CAUTION, DANGER, and
WARNING safety signs.
Keep safety signs in good condition. Replace missing or
damaged safety signs.
CN80434,00007E1-19-30MAR18
Warning Label
P16383—UN—30DEC11
Hydraulic cylinder equipped with restrictor orifices to
reduce speed for implement operation.
PX03972,0000C49-19-28JUL16
P16221—UN—01FEB11
PX03972,0000C47-19-28JUL16
P16385—UN—30DEC11
Avoid injury: stay clear from a gauge wheel.
Gauge wheel swings when plow reverses.
CN80434,00007E2-19-30MAR18
P16386—UN—30DEC11
Avoid crushing injuries when servicing bottoms by
keeping hands away of this area.
PX03972,0000B3B-19-28JUL16
10-1
Preparing the Tractor
Tractor Size For complete a tractor operating instructions, refer to
For tractor horsepower recommendations, refer to your tractor operator's manual.
specification section.
a
Tractor horsepower recommendation varies within the range depending on the ground conditions, soil type and operating parameters (speed-
depth).
b
Tractor horsepower recommendation varies within the range depending on the ground conditions, soil type, and operating parameters (speed-
depth).
CN80434,00007E3-19-30MAR18
Rear Wheel Weighting (1) Front End (2) Add weights to the tractor front if needed for stability.
Weighting (2) Pulling heavy rear-mounted implements tends to lift the
front wheels. Add enough weights to maintain steering
control.
To improve steering, remove front weights when not
required.
Refer to your tractor operator's manual for instructions to
add front weights, use implement code information to
determine the required ballast.
CN80434,00007E4-19-30MAR18
15-1
Preparing the Tractor
Tire Pressure NOTE: The heavier the trash, the more important it is to
Inflate tractor tires as recommended in your tractor remove the drawbar.
operator's manual.
For adjusting lift links and center links, setting lateral
Proper tire pressure is required to get optimal float, load/depth control, and using draft control, see
performance during plowing operation. tractor Operator’s Manual.
PX07220,0000B77-19-28JUL16 CN80434,00007E7-19-30MAR18
LX001802—UN—05JAN95
P6777—UN—15FEB01 Sway Chain
For normal plowing conditions, adjust the tractor rear
15-2
Preparing the Tractor
P11303—UN—06MAY02
Sway Block
RW21745—UN—28JUL92
P7489—UN—19OCT00 P7490—UN—19OCT00
Lift Link Pin - Float Lift Link Pin - No Float Adjusting Center Link
Position Position
A—Float Position
B—Rigid Position
RW55289—UN—28JUN94
15-3
Preparing the Tractor
Hydraulics
A remote cylinder control valve is required to operate the
reversing cylinder.
PX07220,0000B7F-19-28JUL16
P7575—UN—15FEB01
Adjust center link to level plow front to rear. Remove lock
pin (A) and lift latch (B). Rotate center portion of center
link to desired position. Secure latch with lock pin,
measure between centers of pins (C).
CN80434,00007EA-19-30MAR18
15-4
Preparing the Machine
Adjust Gauge Wheel A—Hitch Pin
B—Bushing
Lubrication
P7580—UN—21FEB01
W8422—UN—24JAN89
Lubricate plow as shown in the “Lubrication and
Maintenance section”.
PX07220,0000B82-19-28JUL16
P7577—UN—28FEB01
Bottoms are designed for a maximum depth of 16
inches. Plowing depth is set using the Tractor hitch
control lever and the plow gauge wheels.
W8423—UN—02JUN89
Adjust gauge wheel to be 7 inches (A) from the ground Before starting to work with a new plow or one which has
as initial setting. been stored, check that all bolts and set screws are tight
and all cotter pins spread to keep them from falling out.
NOTE: An increase or decrease in the recommended Check the bolts that hold the plow bottoms to see that
length can be necessary depending on the ground they are properly torqued.
conditions and the desired plowing depth. PX07220,0000B83-19-28JUL16
GS38198,00006FE-19-19MAR18
APY05802—UN—11MAY18
20-1
Operating the Machine
Before Operating the Plow F—Rate of Drop Knob
Verify the following points on the tractor and the plow PX07220,0000B9A-19-28JUL16
6. Check sway blocks position. (see page 15-4). Hitch height limit is controlled by turning control knob
(A). Turning knob fully counterclockwise (B), height is
7. Lateral float pin rigid position (see page 15-5). limited to 25 percent to the maximum height. Turning
knob fully clockwise (C), hitch can be raised to maximum
8. Lift link and center link proper length initial setting
height.
(see page 15-6).
9. Plow gauge wheel initial setting (see page 20-1). NOTE: External raise/lower switch can raise hitch above
selected limit.
10. Hitch selector lever to set working depth (see page
35-4). PX07220,0000B9B-19-28JUL16
Hitch Controls
RW22079—UN—04DEC92
25-1
Operating the Machine
Raise/Lower and Depth Set NOTE: Hitch not lowers if quick coupler has been
removed. Install 68—91 kg (150-200 lb) or quick
coupler of equivalent weight to hitch for normal
operation.
CN80434,00007F0-19-02APR18
Load/Depth Control
RW22077—UN—04DEC92
To set implement working depth, move stop (B) against CAUTION: To prevent hitch movement and
lever by turning stop wheel (C). Hitch lowers to same possible injury, turn load/depth control (1) fully
working depth each time. If necessary to lower the hitch counterclockwise before attaching or detaching
below the preset depth, the control lever can be lifted implements.
and pushed past the stop.
Hitch has operating modes: “position” (1) or “pull” (5).
Raise/lower switch (D) allows raising and lowering
during turns, without having to move the hitch control PX07220,0000B9E-19-28JUL16
25-2
Operating the Machine
RW55272—UN—21JUL94
APY05257—UN—20MAR18
In order to get a straight opening furrow, drive straight
forward without looking back.
After first furrow has been completed, start the second
furrow by dropping the plow with tractor wheels in the
opening furrow. Drive forward a few feet, and stop.
Level plow fore/aft. Never cut front bottom deeper than
the rear bottom.
Level plow side to side width of cut always be the same
RW55273—UN—21JUL94 for all bottoms.
When load/depth knob is turned to numbered (3), allows
depth and load control to be varied as ground conditions As a final check, observe plow and make sure that all of
require. The setting of the control depends on implement the recommended adjustments have been made.
being used and field or soil conditions. If plow is not operating properly after the third furrow,
Turning the knob counterclockwise reduces draft see Troubleshooting section.
response (1). Before using a new plow or one which has been stored
Turning the control clockwise increases draft response. be sure that all the bolts are tight and all cotter pins
With the control turned to a higher number (5), the spread to keep them from falling out. Check for loose
implement is raised as resistance (Soil density) bolts, screws, and parts when lubricating the plow. Be
increases and lowered as resistance decreases. Typical sure that the bolts that hold the plow bottoms to the
settings: standards are properly torqued.
CN80434,0000872-19-16MAY18
25-3
Operating the Machine
Landsides for Side Draft Control Check the landside for wear and if necessary reverse or
replace the landside.
3 BOTTOMS PLOW LANDSIDE
This 975 plow is equipped with two landsides (B) per
bottom (see fig.1). Rear bottom includes two larger
landsides (B), and support (H) (see fig.2). As an option
when the soil is sandy, humid or soft is equipped with
one landside (B) and one wedge (D) on each side of
bottom (see fig.3). Rear bottom includes one larger
landside (B), one larger wedge (D) and support (H) (see
fig.4).
P6392—UN—02NOV95
(Fig.1) 4 BOTTOMS PLOW LANDSIDE
This 975 plow is equipped with two landsides (B) on
each side of bottom (see fig.1) . Rear bottom includes
two larger landsides (B) and support (H) (see fig.2)
5 BOTTOMS PLOW LANDSIDE
This 975 plow is equipped with one landside (B) on each
side of bottom. Rear bottom includes one larger landside
(B) and support (H). (Figure not shown).
Amount of Landsides
Plow Hard Soil Condition Soft Soil Condition
Landsides Wedge Landsides
Wedge on
Ser- Bot- on each on each on each
each side
ies toms side of side of side of
of bottom
bottom bottom bottom
975 3 2 0 1 1a
P6394—UN—02NOV95 975 4 2 0 2 0
(Fig.3) 975 5 1 0 1 0
a
As required, based in your local soil conditions.
CN80434,00007F3-19-16MAY18
P6395—UN—02NOV95
Rear Bottom (Fig.4)
25-4
Operating the Machine
tractor actuates the remote cylinder on the plow. Moving Secure the safety tension bolt to avoid the implement
the lever one way extends the cylinder for right-hand from unnecessary damage.
plowing, moving the lever the other way retracts the
cylinder for left-hand plowing. NOTE: Keep enough stock of safety tension bolts (A) to
prevent loss of time. Do not use any other bolt than
CAUTION: The operator should be sure that indicated.
everyone is safely clear of the plow before
reversing . Before reversing the plow sure no
one is near the machine as it causes an injury
CN80434,00007F4-19-02APR18
Operating Speed
APY05825—UN—18MAY18
IMPORTANT: To obtain best results during
operation, do not vary tractor speed, engine Install tension bolt (5/16” x 2.50” SAE 8 and 2 nuts and
rpm, plow depth, and load control. tighten to 41 N·m (30 lb·ft).
Use the two holes (B) on each bottom for storing safety
IMPORTANT: The Tractor minimum operating speed tension bolts.
recommended is 3.1 mi/h (5 Km/hr).
In order to work in better conditions of plowing,
CN80434,00007F5-19-02APR18 depending on soil and working depth desired, the tractor
minimum operation speed recommended is 2 to 3 mi/h
(4 to 6 km/hr) to avoid damage the plow working above
the speed specified.
Safety Tension Bolt Standards
CN80434,0000873-19-16MAY18
IMPORTANT: The safety tension bolt (A) in the
standard is a protection mechanism to avoid
constant loads of operation, they are used to
protect the bottoms, plow frame and Tractor Safety Trip Standards (Optional)
when the share point hits a solid obstruction
such as stones or roots in the field.
APY05806—UN—11MAY18
The plow could be equipped with Safety Trip Standards.
When the share point hits a solid obstruction, the plow
APY05804—UN—11MAY18 bottom trips, protecting the plow bottom and plow frame.
The plow is available with a safety tension bolt To reset safety trip standard after it has tripped, raise the
standards (A). The safety tension bolt in the standard, plow into transport position and standard will return to
protects the plow bottom and plow frame when the working position.
share point hits a solid obstruction.
25-5
Operating the Machine
CN80434,00007DC-19-29MAR18
APY05808—UN—11MAY18
If the safety trip is stuck, remove any dirt & clean it. Do
not forget to clean in the rear area between standard
support and bottom, in order to eliminate obstructions of
weed or free soil.
APY05807—UN—11MAY18
The safety trip has an adjusting screw (A) with lock nut
(B) in order to an safety trip has more sensibility.
Adjusting screw as follows: Loose the nut (B) and turn
an screw clockwise until to obtain more sensibility and
tighten the nut (B).
CN80434,00007DD-19-29MAR18
25-6
Attaching and Detaching
Load/Depth Control Pull external raise/lower switch (A) outward and push
switch up to raise hitch, or down to lower.
CN80434,00007F7-19-02APR18
PX07220,0000B84-19-28JUL16
RW22077—UN—04DEC92
RW22081—UN—04DEC92
30-1
Attaching and Detaching
knob fully clockwise (C), hitch can be raised to maximum Quick coupler is convertible to category 3 or category
height. 3N.
Category 3 or 3N is recommended on this plow.
NOTE: External raise/lower switch can raise hitch above
selected limit. PX07220,0000B89-19-28JUL16
PX07220,0000B87-19-28JUL16
CN80434,00007F9-19-02APR18
Hoses Position
APY05809—UN—11MAY18
Install the mast hitch pin in the corresponding hole
according to the category being used (see following
table.)
CN80434,0000871-19-15MAY18
P14298—UN—25OCT06
1. Install the support for hydraulic hoses on the weld
Hitch Conversion Quick Coupler bracket.
RW55294—UN—28JUN94
30-2
Attaching and Detaching
RW22649—UN—25JUN93
P5186—UN—17FEB93
Your tractor could be equipped with SCV's that accept a
standard hose tip as recommended by ISO*1 and
SAE**2. This tip allows more flow and therefore shorter
lift times. It is recommended that the implements
connectors be converted to ISO tips. Adapters are RW21239—UN—18JUN92
available to adapt the ISO tips to older John Deere CAUTION: Push SCV lever lockout to the right
Tractors. (transport lock) before attaching implements to
prevent implement movement and possible
ISO hose tip - (A) personal injury.
John Deere hose tip - (B)
IMPORTANT: Hydraulic hoses fails due to physical
PX07220,0000B8C-19-28JUL16 damage, kinks, age and exposure. Check hoses
regularly. Replace damaged hoses.
Be sure that the hose ends are clean prior to
use to minimize hydraulic system
1
International Standard Organization. contamination.
2
Society of Automotive Engineers.
30-3
Attaching and Detaching
RW21757—UN—21AUG92
Adjusting Rate of Cylinder
Knob Position Function of Lever Detent
PX07220,0000B90-19-28JUL16
CN80434,00007FB-19-02APR18
Turn control knob (A) counterclockwise (B) to decrease
drop speed, or clockwise (C) to increase drop speed.
CN80434,00007FC-19-02APR18
30-4
Attaching and Detaching
RW21226—UN—12JUN92
P6779—UN—12MAY97
Push lever (A) down to re move hoses.
SCV lever lockouts (A) have three position settings: 1. Place bottoms to the middle position and lower the
plow to the ground.
● Left—full lever travel
2. Detach plow from tractor and drive tractor forward.
● Center—float lockout
● Right—transport lock IMPORTANT: It is necessary to change length of
center link to unhitch.
Each SCV lever has four positions—Neutral, Extend,
Retract, and Float. CAUTION: To avoid injury from escaping
PX07220,0000B93-19-28JUL16 hydraulic oil under pressure, turn engine off
and relieve the pressure in the system by
moving remote cylinder operating levers in both
directions before attaching or detaching hoses
from the breakaway couplers.
CN80434,00007FE-19-15MAY18
30-5
Attaching and Detaching
RW55146—UN—03DEC93
1. Raise both latch levers (A) with implement raised.
2. Disconnect hydraulic hoses and electrical
connections.
3. Lower implement to ground. Continue lowering quick-
coupler until hook clears implement hitch pins.
4. Carefully drive tractor away from implement.
PX07220,0000B95-19-28JUL16
30-6
Transporting
Plow Position for Transport Use Safety Lights and Devices
APY05261—UN—20MAR18
When transporting, lift the plow to prevent damage.
CN80434,0000874-19-16MAY18
35-1
Assembly
Set up Time Safety Reflector Without Rear Gauge Wheel
MOLDBOARD HOURS
3 - BOTTOMS 1.5
4 - BOTTOMS 2.0
5 - BOTTOMS 2.3
GENERAL INFORMATION
Read all assembly instructions and carefully observe
illustrations.
Safety Reflector
P6846—UN—17JUL97
Use an overhead crane or hoist to lift frame.
Place 94 cm (37”) minimum height stands under rear
and front, and lower frame so it rests on stands.
CN80434,0000803-19-03APR18
P6786—UN—12MAY97
Install the bracket with red reflector rearward, remove
only the nut on bolt of rear gauge wheel support.
PX07220,0000BC0-19-28JUL16
40-1
Assembly
Installing the Pivot Pin When you installing a pivot pin on the plow, follow these
steps:
1. Place the pivot pin (A) into the cavity of the sleeve (B)
installing the castle nut (C) before assembling the pin
with cotter pin (D).
2. In order to set the free play between pivot pin and
frame, install the pin with cotter pin (D), place the
washers (E) as required, and secure with cotter pin
(C) on the castle nut.
3. Verify the free play (H) between bottoms frame (G)
and main frame (F). The minimum should be set to (1
- 1.5 mm; tighten the castle nut completely and back
in the slot, until it matches with the cotter pin hole.
PX07220,0000BC3-19-28JUL16
P6850—UN—26JUL97
P7584—UN—10MAR01
Install the standard support bolts as shown, in order to NOTE: The black holes in the extension frame show the
obtain 16” or 18” of bottom cut, as required. place where the bottoms should be installed to
obtain he desired cutting width.
PX07220,0000BC4-19-28JUL16
40-2
Assembly
P7585—UN—10MAR01
Leave bolts loose until parts are completely assembled,
and then tighten bolts to torque shown in page 55-9.
PX07220,0000BC5-19-28JUL16
40-3
Assembly
Installing Bottoms 2. Remove from bottoms the bolts (A) and spacer (B)
need to attach as per the standard. Place spacer in
CAUTION: Shares of bottoms are sharp. Use the hole of the standard.
extreme caution when working around plow.
3. Using an overhead crane or hoist, place the bottoms
(with landsides installed) on standards. Attach with
bolts and nuts.
APY05816—UN—11MAY18
40-4
Assembly
P16257—UN—11APR11
Remove screw (A) from the Shank if applied.
CN80434,0000805-19-03APR18
P4180—UN—02APR93
A—Adapter
P6795—UN—12MAY97 B—O-Ring
C—Hose
D—Orifice
E— Screwdriver
F—Rod End
G—Special Nut
40-5
Assembly
Install on remote cylinder the rod end (F) with special nut
(G).
When the rod end (F) is installed be sure that the
distance is 51.43 cm (20.25”) when remote cylinder is
fully retracted.
Verify that the distance is 71.75 cm (28.25”) when
remote cylinder is fully extended.
CN80434,0000806-19-03APR18
40-6
Attachments
Gauge Wheel Installation frame. Install the collar to the yoke pivot shaft, using 1/2”
x 3-3/4” cap screw (C), washer (0.531” x 1.125” x
0.105”) and nut 1/2”.
When the spacing between collar and sleeve is more
than 0.125”, add adjusting washers as required.
P6786—UN—12MAY97
The gauge wheel is used to maintain consistent plowing
depth in loose or sandy soil conditions.
To install the gauge wheel attachment, proceed as
follows:
Cut all bundling wires and conveniently arrange parts.
P6787—UN—12MAY97
1.- Assembly to gauge wheel frame the yoke end of
P6791—UN—09MAR01
adjusting arms with headed pin (A) and the cotter pin
(B). IMPORTANT: Grease every 25 hours with an John
Deere Multipurpose lubricant or an equivalent
SAE Multipurpose-Type grease.
CN80434,0000815-19-04APR18
P6788—UN—12MAY97
2.- Install an yoke (A), on frame using a washer (2.062” x
3.00” x 0.075”) between collar (B) and gauge wheel
45-1
Troubleshooting
Troubleshooting
Symptom Problem Solution
Working without gauge wheel. Install and adjust gauge wheel (see
page 40-1).
Plow not running straight. Bottoms not scouring. If metal moldboard, remove paint and
clean frequently until land polish is
attained.
Improper lateral adjustment. Both right hand side and left hand side
lift links should have same dimension.
50-1
Troubleshooting
Insufficient rear landside pressure Adjust tractor center link (see page 15-
6).
CN80434,0000808-19-03APR18
Troubleshooting
Symptom Problem Solution
Improper lateral adjustment. Both right hand side and left hand side
lift links should have same dimension.
Plow not level fore-and-aft. Adjust center link to level plow fore-
and-aft.
Front bottoms cutting too wide or too Check tractor wheel tread setting. (see
narrow. page 15-4)
Improper gauge wheel adjustment. Adjust gauge wheel (see page 20-1
and 40-1).
Poor trash coverage. Bottoms not scouring. If metal moldboard, remove paint and
clean frequently until land polish is
attained.
CN80434,0000809-19-03APR18
Troubleshooting
Symptom Problem Solution
Excessive tractor wheels slippage. Improper sensitivity adjustment. Adjust sensitivity (see page 35-5).
50-2
Troubleshooting
Working without gauge wheel. Install and adjust gauge wheel (see
page 20-1 and 40-1).
Main frame and bottom frame Check gap between both, main frame
interference. and bottom frame.
Tension bolt breaks too often. Incorrect tension bolt. Use proper tension bolt (see page 55-
2).
Bottom frame and standard excessive Check pivot bolt for proper torque (see
gap page 65-6).
Bottom not return to normal position. Keep the safety trip out of dirt.
Safety trip trips or tension bolts Plow running on nose. Adjust center link to level plow fore
breaks too often only in front and aft.
bottom.
Excessive cut on front bottom plow Check tractor wheel tread setting. (see
page 15-4).
Safety trip not reset. Frog plates and standards excessive Check bottom pivot bolt for proper
gap. torque (see page 65-6).
Tension bolt bigger than specified. Check the specified tension bolt (see
page 55-2).
50-3
Troubleshooting
Bottom uneven cut working on left Improper reverse mechanism Check the working position of bottom
or right direction. adjustment. frame is at the end of its stroke, both
sides.
CN80434,000080A-19-03APR18
50-4
Lubrication and Maintenance
Grease IMPORTANT: Lubricate with John Deere
Multipurpose Lubricant or an equivalent SAE
multipurpose type grease at hourly intervals indicated on
the symbols. Twice a day apply SAE 30 oil to the rest of
moving parts.
TS1654—UN—14MAR96
W8422—UN—24JAN89
Use grease based on NLGI consistency numbers and
the expected air temperature range during the service
interval.
The following greases are preferred:
● John Deere HIGH TEMPERATURE EP GREASE
● John Deere MOLY HIGH TEMPERATURE EP
GREASE
● John Deere GREASE-GARDTM P15074B—UN—30NOV07
Other greases are used if they meet one of the Lubricate two grease fittings on Safety Trip or Tension
following: Bolt every 10 hours.
● NLGI Performance Classification GC-LB NOTE: In some wet conditions is necessary lubricate the
pin holes in the safety trip, remove the plugs and
Clean grease fittings before using grease gun. Replace install grease fittings, apply grease as required and
any lost or broken fittings immediately. place the plugs that were removed.
SYMBOLS
55-1
Lubrication and Maintenance
P6799—UN—09MAR01
Lubricate reversion arm (two fittings on both ends).
P6841—UN—09MAR01
PX07220,0000BAE-19-28JUL16
P6845—UN—09MAR01
Lubricate three fittings on pivot pin on the main frame
every 25 hours.
PX07220,0000BAD-19-28JUL16
P6791—UN—09MAR01
Lubricate one fitting on gauge wheel axle.
PX07220,0000BAF-19-28JUL16
Lubricating Reversion Arm
P6798—UN—09MAR01
P6843—UN—09MAR01
Two and Three Bottom Plow
55-2
Lubrication and Maintenance
P7591—UN—27FEB01
Four and Five Bottom Plow
P7637—UN—13MAR01
Roller Assembly
55-3
Service
Bottoms IMPORTANT: The lubrication periods recommended
are based on normal conditions, Severe or
unusual conditions requires more frequent
lubrication.
CN80434,000080E-19-03APR18
Tension Bolt
P4541—UN—21MAR94
P12379A—UN—30NOV07
P6374—UN—30OCT95
60-1
Service
60-2
Service
Wheel Bearings when cylinder is extended. If not, loosen special nut (D)
and turn remote hydraulic cylinder rod end as needed to
obtain this distance. Tighten special nut.
PX07220,0000BB9-19-28JUL16
Verification
P4523—UN—22MAR93
Inspect wheel bearings before the plowing season and
repack with John Deere Multi-Purpose Lubricant or an
equivalent SAE multipurpose-type grease. Tighten the
adjusting nut. At the same time turn wheel in both
directions until there is a slight drag to be sure that all
bearing surfaces are in contact.
P6847—UN—27FEB01
A good performance of the reversing mechanism is
required to obtain an even depth when working either
with bottoms in the right or left-hand positions.
If the reversing mechanism is not operating properly it
can result in mechanism damage, inefficient operation,
and rapid parts wear.
SET UP
The reversing mechanism has been preset at the factory
but if necessary to repeat this setup procedure, after
replacing parts, etc, follow these steps: RW55330—UN—07JUL94
1.- With plow attached to the tractor, and remote CAUTION: Excessive operating speed causes
hydraulic cylinder (retracted and free of pressure) damage or injury. Full extension or retraction of
installed on plow, verify that length distance (A) from pin cylinder takes at least 2 seconds. Rate slows
(B) to pin (C), is 514 mm (20-1/4") or 717 mm (28-1/4") enough to be safe, yet fast enough to be
practical.
60-3
Service
Adjust rate of operation for each job. Rate slows enough SCV Flow Settings l/s gal/min
to be safe, yet fast enough to be practical. 8.0 1.33 21.0
Change flow setting as follows. 9.0 1.84 29.0
10.0 1.90 30.0
1. Press selected SCV switch (A). Display below the a
0.1 Minimum Flow Setting
touch switch shows previous rate of flow.
CN80434,0000875-19-18MAY18
2. Turn flow rate knob (D) clockwise (rabbit) to increase
flow or counterclockwise (turtle) to decrease flow.
Flow setting is shown on paragraph display (C) and,
during adjustment, on digital display (B). Adjusting Selective Control Valve Flow Rate
(Flow Control Setting)
NOTE: Flow settings take effect immediately. SCV can
be operated to observe flow rate while in
adjustment mode.
APY05833—UN—18MAY18
0.1a — —
D—Orifice
1.0 0.06 1.0 E—Screwdriver
2.0 0.16 2.5
3.0 0.25 4.0 NOTE: Be sure that orifices for speed reduction are
4.0 0.32 5.0 installed on hydraulic remote cylinder.
5.0 0.41 6.5
CN80434,0000876-19-18MAY18
6.0 0.53 8.3
7.0 0.69 11.0
TS1671—UN—01MAY03
SAE Grade 1a SAE Grade 2b SAE Grade 5, 5.1 or 5.2 SAE Grade 8 or 8.2
c
Bolt or Screw Hex Head Flange Hex Headc Flange Hex Headc Flange Hex Headc Flange Headd
Size Headd Headd Headd
N·m lb·in N·m lb·in N·m lb·in N·m lb·in N·m lb·in N·m lb·in N·m lb·in N·m lb·in
1/4 3.1 27.3 3.2 28.4 5.1 45.5 5.3 47.3 7.9 70.2 8.3 73.1 11.2 99.2 11.6 103
N·m lb·ft N·m lb·ft
5/16 6.1 54.1 6.5 57.7 10.2 90.2 10.9 96.2 15.7 139 16.8 149 22.2 16.4 23.7 17.5
N·m lb·ft N·m lb·ft
3/8 10.5 93.6 11.5 102 17.6 156 19.2 170 27.3 20.1 29.7 21.9 38.5 28.4 41.9 30.9
N·m lb·ft N·m lb·ft
7/16 16.7 148 18.4 163 27.8 20.5 30.6 22.6 43 31.7 47.3 34.9 60.6 44.7 66.8 49.3
N·m lb·ft N·m lb·ft
1/2 25.9 19.1 28.2 20.8 43.1 31.8 47 34.7 66.6 49.1 72.8 53.7 94 69.3 103 75.8
9/16 36.7 27.1 40.5 29.9 61.1 45.1 67.5 49.8 94.6 69.8 104 77 134 98.5 148 109
60-4
Service
SAE Grade 1a SAE Grade 2b SAE Grade 5, 5.1 or 5.2 SAE Grade 8 or 8.2
c c c
Bolt or Screw Hex Head Flange Hex Head Flange Hex Head Flange Hex Headc Flange Headd
Size Headd Headd Headd
5/8 51 37.6 55.9 41.2 85 62.7 93.1 68.7 131 96.9 144 106 186 137 203 150
3/4 89.5 66 98 72.3 149 110 164 121 230 170 252 186 325 240 357 263
7/8 144 106 157 116 144 106 157 116 370 273 405 299 522 385 572 422
1 216 159 236 174 216 159 236 174 556 410 609 449 785 579 860 634
1-1/8 305 225 335 247 305 225 335 247 685 505 751 554 1110 819 1218 898
1-1/4 427 315 469 346 427 315 469 346 957 706 1051 775 1552 1145 1703 1256
1-3/8 564 416 618 456 564 416 618 456 1264 932 1386 1022 2050 1512 2248 1658
1-1/2 743 548 815 601 743 548 815 601 1665 1228 1826 1347 2699 1991 2962 2185
The nominal torque values listed are for general use only with the assumed Replace fasteners with the same or higher property class. If
wrenching accuracy of 20%, such as a manual torque wrench. higher property class fasteners are used, tighten these to the
DO NOT use these values if a different torque value or tightening procedure is strength of the original.
given for a specific application.
For lock nuts, for stainless steel fasteners, or for nuts on U-bolts, see the
tightening instructions for the specific application.
● Make sure that fastener threads are clean.
● Apply a thin coat of Hy-Gard™ or equivalent oil under the head and on the threads of the fastener, as shown in the following image.
● Be conservative with the amount of oil to reduce the potential for hydraulic lockup in blind holes due to excessive oil.
● Properly start thread engagement.
TS1741—UN—22MAY18
a
Grade 1 applies for hex cap screws over 6 in (152 mm) long, and for all other types of bolts and screws of any length.
b
Grade 2 applies for hex cap screws (not hex bolts) up to 6 in (152 mm) long.
c
Hex head column values are valid for ISO 4014 and ISO 4017 hex head, ISO 4162 hex socket head, and ISO 4032 hex nuts.
d
Hex flange column values are valid for ASME B18.2.3.9M, ISO 4161, or EN 1665 hex flange products.
DX,TORQ1-19-30MAY18
TS1742—UN—31MAY18
60-5
Service
TS1741—UN—22MAY18
a
Hex head column values are valid for ISO 4014 and ISO 4017 hex head, ISO 4162 hex socket head, and ISO 4032 hex nuts.
b
Hex flange column values are valid for ASME B18.2.3.9M, ISO 4161, or EN 1665 hex flange products.
DX,TORQ2-19-30MAY18
60-6
Storage
Keep Your Plow Prepared
Store plow in a dry place if possible.
Clean plow thoroughly. Dirt attracts moisture and rust
steel.
Repaint all parts where paint is worn or scratched.
Check all hardware and see that it is tight.
Replace any worn, missing or broken parts.
Coat bottoms with a heavy coat of rust-preventive
grease or oil.
Lubricate machine (See Lubrication and maintenance
section).
Apply a good rust preventive such as John Deere plow
bottom black paint when storing plow for the season.
John Deere plow bottom black paint is available in brush
type (PT-64) or in 12 oz. (0.035 L) spray cans (PT-65).
CN80434,0000816-19-04APR18
65-1
Specifications
Specifications Specifications
70-1
Specifications
code. It assists your John Deere dealer in giving you Month Code Month Code Month Code Month Code
prompt and efficient service. Janu- A April D July G Octo- K
ary ber
They are also needed for law enforcement, to trace your
machine in case it is ever stolen. Febru- B May E Au- H No- L
ary gust vem-
ACCURATELY record these characters in spaces ber
provided. March C June F Sep- J De- M
tem- cem-
1
ber ber
Date Purchased
________________________________ Number of Moldboard Code
Content of Individual Positions or Group of Position 3 A
- Character Products Serial Number 4 B
5 C
VG41678,000007A-19-23MAR15
PY21814—UN—26SEP14
1P00975AKEC013836
1P0 0975 A K E C 013836
A B C D E F G
PY21816—UN—01OCT14
A—World Manufacturer code
B—Model Identifier
C—Additional Product Information According to Table 3
D—Assigned for Deere System
E—Calendar Year of Manufacture According to Table 1
F—Calendar Month of Manufacture According to Table 2
G—Serial Number
1
(Specifications and design subject to change without notice.)
70-2
John Deere Service Keeps You On The Job
John Deere Parts School is never out for John Deere service technicians.
Training schools are held regularly to be sure our
personnel know your equipment and how to maintain it.
Result?
Experience you can count on!
DX,IBC,C-19-04JUN90
Prompt Service
TS100—UN—23AUG88
We help minimize downtime by putting genuine John
Deere parts in your hands in a hurry.
That’s why we maintain a large and varied inventory—to
stay a jump ahead of your needs.
DX,IBC,A-19-04JUN90
TS101—UN—23AUG88
Precision tools and testing equipment enable our
Service Department to locate and correct troubles
quickly . . . to save you time and money.
DX,IBC,B-19-04JUN90
Well-Trained Technicians
TS102—UN—23AUG88
IBC-1
John Deere Service Literature Available
Technical Information
Technical information can be purchased from John
Deere. Publications are available in print or CD-ROM
format.
Orders can be made using one of the following:
● John Deere Technical Information Store: www.
JohnDeere.com/TechInfoStore
● Call 1-800-522-7448
● Contact your John Deere dealer
TS189—UN—17JAN89
PARTS CATALOGS list service parts available for your
machine with exploded view illustrations to help you
identify the correct parts. It is also useful in assembling
and disassembling.
TS1663—UN—10OCT97
EDUCATIONAL CURRICULUM including five
comprehensive series of books detailing basic
information regardless of manufacturer:
● Agricultural Primer series covers technology in
farming and ranching.
● Farm Business Management series examines “real-
world” problems and offers practical solutions in the
areas of marketing, financing, equipment selection,
and compliance.
TS191—UN—02DEC88 ● Fundamentals of Services manuals show you how to
OPERATOR’S MANUALS providing safety, operating, repair and maintain off-road equipment.
maintenance, and service information. ● Fundamentals of Machine Operation manuals
explain machine capacities and adjustments, how to
improve machine performance, and how to eliminate
unnecessary field operations.
● Fundamentals of Compact Equipment manuals
provide instruction in servicing and maintaining
equipment up to 40 PTO horsepower.
DX,SERVLIT-19-07DEC16
SLIT-1
Notes