VX-3008 System Manager Datasheet
VX-3008 System Manager Datasheet
VX-3008 System Manager Datasheet
VX-3008F
VOIR REF VX-3008F C01
Key features
• Up to 3 amps (8 zones switching between 2 amps + standby amp or 8 zones freely assignable to 1 of 2 amps)
• All mandatory indications by EN54-16
• Status indication for each speaker line
1
VX-3008F | Datasheet
2
Published on 2024/04/27
VX-3008F | Datasheet
Specifications
Control Input 1, 2 16 inputs, no-voltage make contact input, open voltage: 24 V DC, short-circuit current: 2 mA,
Fault Detection System: Short circuit, Open circuit, Method: Voltage detect
Connector: RJ45 connector,
Connection Cable: Shielded Category 5 twisted pair cable (CAT5-STP) or greater
3
Published on 2024/04/27
VX-3008F | Datasheet
ATT/Control Output 8 outputs, no-voltage make contact, relay contact (NC, NO, C),
control current: 2 mA to 5 A, withstand voltage: 125 V AC, 40 V DC
Connector: Removable terminal block (12 pins) x 2
Equalizer/Filter 3 bands for each audio input and RS LINK (A/B), 6 bands for each amplifier output
Parametric equalizer: 20 Hz – 20 kHz, ±15 dB, Q: 0.267 – 69.249
Filtering: High-pass filter 20 Hz – 20 kHz, 6 dB/oct, 12 dB/oct
Low-pass filter 20 Hz – 20 kHz, 6 dB/oct, 12 dB/oct
High shelving filter 6 – 20 kHz, ±15 dB
Low shelving filter 20 – 500 Hz, ±15 dB
Notch filter (amplifier output only) 20 Hz – 20 kHz, Q: 8.651 – 69.249
All-pass filter (amplifier output only) 20 Hz – 20 kHz, Q: 0.267 – 69.249
Horn equalizer (amplifier output only) 20 kHz, 0 to +18 dB (0.5 dB steps)
ANC (Ambient Noise Control) Amplifier output level control, Automatic sensor input reference level measuring,
Sensor input reference level fine adjustment
Maximum output signal level control: –15 to 0 dB
Minimum output signal level control: –18 to –3 dB
Sample time setting: 10 s, 20 s, 30 s, 1 min, 5 min
Gain ratio setting: (Ambient noise: Output signal level) 6:3, 5:3, 4:3, 3:3, 3:4, 3:5, 3:6
Ambient noise measuring frequency setting: 20 Hz – 20 kHz, 3 points
Module Slot Number of modules: 3 (When the lin output module is installed x 2)
DA CONTROL LINK x 3,
DA OUTPUT LINK x 3 (Used only when a power amplifier module is installed)
4
Published on 2024/04/27
VX-3008F | Datasheet
Indicators POWER (green) x 1, RUN (green) x 1, EMERGENCY (red) x 1, CPU OFF (red) x1, LAN A (green) x 1,
LAN B (green) x 1, RS LINK A (green) x 1, RS LINK B (green) x 1
FAULT STATUS (yellow): GENERAL x 1, UNIT x 1, NETWORK x 1, EMG MIC x 1, FUSE x 1, POWER
x 1, CPU x 1, ZONE x 8
AMPLIFIER: PEAK (red) x 3, SIGNAL (green) x 3, OPERATE (green) x 3, POWER (green) x 3
Dimensions 483 (W) x 132.6 (H) x 345 (D) mm (19.02" x 5.22" x 13.58")
Included Accessories Rack mounting screw x 4, Removable terminal plug (2 pins) x 6, Removable terminal plug (4 pins) x
1, Removable terminal plug (6 pins) x 2, Removable terminal plug (12 pins) x 2, Removable terminal
plug (17 pins) x 1, CD (PC setting software) x 1, Ferrite clamp x 2
(*1) TOA's unique technology which makes it possible to trasmit high-quality autdio signals in real time over an IP network.
(*2) 0 dB = 1 V
(*3) Module: Digital power amplifier module, Line output module
5
Published on 2024/04/27
VX-3008F | Datasheet
Dimensions
AMPLIFIER SBY AMPLIFIER 2 AMPLIFIER 1
E
1 C
H
E
Rear View
2 C
H
IN
VOICE EVACUATION FRAME
VX-3008F SP OUT
TOA Corporation
OUT
H C H C H C H C H C H C H C H C H C H C H C E 2 1 2 1 B A
8 7 6 5 4 3 2 1 CONTROL OUT CONTROL IN LAN
483 [19.02"]
4-6 10
466 [18.35"] [0.24" 0.39"]
POWER
RUN
132.6 [5.22"]
Front View
EMERGENCY
CPU OFF
LAN A
LAN B
RS LINK A
RS LINK B
AMPLIFIER FAULT STATUS
1 2 SBY ZONE ACK RESET LAMP TEST
PEAK GENERAL
1 2 3 4 5 6 7 8
SIGNAL FUSE UNIT
OPERATE POWER NETWORK
POWER CPU EMG MIC
VOICE EVACUATION FRAME VX-3008F
57.2 [2.25"]
6
Published on 2024/04/27
VX-3008F | Datasheet
Dimensions
345 [13.58"]
Side View
AUDIO
INPUT VOL
1
4
RESET
ID NUMBER
7
Published on 2024/04/27
VX-3008F | Datasheet
A&E specifications
Frame for 3 amplifier modules with 8 monitored speaker outputs.
Two amplifier modules can be assigned to any speaker output.
Speaker outputs with overlapping amplifiers will automatically choose the amplifier which signal has to be transmitted.
This allows a simultaneous broadcast of two different audio signals per frame to achieve an interruption-free BGM operation
during a paging.
The third amplifier module can be used as standby amplifier.
Up to 4 base frames of this type can be cascaded to increase the number of assignable speaker outputs.
Monitoring is possible by impedance surveillance or by using an end-of-line module.
Settings for impedance deviation to indicate an open or shorted line can be individually set for every output.
4 general balanced audio inputs (microphone/line level) and 2 inputs for up to 8 remote microphones including up to two
emergency microphones.
The signals at the general audio inputs can be mixed.
All mandatory indications and controls regarding EN54-16 can be found on the front panel.
Fault indication for every speaker output line.
Redundant network connection (Ethernet) of the base frame with RSTP via two RJ45 ports.