75W Single Output Switching Power Supply SCP-75 series

■ Features :
%Universal AC input/Full range
%Protections: Short circuit / Overload / Over voltage / Battery
polarity protections (by fuse)
%Built-in temperature compensation function
%Output voltage detection signal
%Cooling by free air convection
%LED indicator for power on
%No load power consumption <0.75W
%100% full load burn-in test
SPECIFICATION %2 years warranty
MODEL SCP-75-12 SCP-75-24
DC VOLTAGE 13.8V 27.6V
RATED CURRENT 5.4A 2.7A
CURRENT RANGE 0 ~ 5.4A 0 ~ 2.7A
PEAK 5S Note.6 6.5A 3.2A
RATED POWER 74.5W 74.5W
RIPPLE & NOISE (max.) Note.2 120mVp-p 200mVp-p
OUTPUT
VOLTAGE ADJ. RANGE +15,-5% +15,-5%
VOLTAGE TOLERANCE Note.3 ± 2.0% ± 1.0%
LINE REGULATION Note.4 ± 1.0% ± 1.0%
LOAD REGULATION Note.5 ± 2.0% ± 1.0%
SETUP, RISE TIME 500ms, 30ms/230VAC 1200ms, 30ms/115VAC at full load
HOLD UP TIME (Typ.) 50ms/230VAC 16ms/115VAC at full load
VOLTAGE RANGE 85 ~ 264VAC 120 ~ 370VDC
FREQUENCY RANGE 47 ~ 63Hz
EFFICIENCY (Typ.) 81% 85%
INPUT
AC CURRENT (Typ.) 1.5A/115VAC 0.9A/230VAC
INRUSH CURRENT (Typ.) COLD START 45A
LEAKAGE CURRENT <2mA / 240VAC
TEMP. COMPENSATION By NTC (not provide with the power supply)
FUNCTION
OUTPUT VOLTAGE SENSOR L=output voltage +0.2 ~ 0.7V(AC OK); L=0V(AC Fail)
6.5 ~ 8.7A rated output power 3.2 ~ 4.3A rated output power
OVERLOAD
Protection type : Hiccup mode, recovers automatically after fault condition is removed
PROTECTION
16.6 ~ 19.3V 33.1 ~ 38.6V
OVER VOLTAGE
Protection type : Shut down o/p voltage, re-power on to recover
WORKING TEMP. -20 ~ +60℃ (Refer to output load derating curve)
WORKING HUMIDITY 20 ~ 90% RH non-condensing
ENVIRONMENT STORAGE TEMP., HUMIDITY -40 ~ +85℃, 10 ~ 95% RH
TEMP. COEFFICIENT ± 0.05% /℃ (0 ~ 45℃)
VIBRATION 10 ~ 500Hz, 2G 10min./1cycle, period for 60min. each along X, Y, Z axes
SAFETY STANDARDS UL60950-1, CB(IEC60950-1),CCC GB4943 approved
SAFETY & WITHSTAND VOLTAGE I/P-O/P:3KVAC I/P-FG:1.5KVAC O/P-FG:0.5KVAC
EMC ISOLATION RESISTANCE I/P-O/P, I/P-FG, O/P-FG:100M Ohms / 500VDC / 25℃/ 70% RH
(Note 6) Compliance to EN55022 (CISPR22) Class B, EN61000-3-2,3
EMC EMISSION
EMC IMMUNITY Compliance to EN61000-4-2, 3, 4, 5, 6, 8,11, ENV50204, EN55024, EN61000-6-1, light industry level, criteria A
MTBF 461.2K hrs min. MIL-HDBK-217F (25℃)
OTHERS DIMENSION 159*97*38mm (L*W*H)
PACKING 0.5Kg; 30pcs/16Kg/1CUFT

1. All parameters NOT specially mentioned are measured at 230VAC input, rated load and 25℃ of ambient temperature.
NOTE 2. Ripple & noise are measured at 20MHz of bandwidth by using a 12" twisted pair-wire terminated with a 0.1uf & 47uf parallel capacitor.
3. Tolerance : includes set up tolerance, line regulation and load regulation.
4. Line regulation is measured from low line to high line at rated load.
5. Load regulation is measured from 0% to 100% rated load.
6. 33% Duty cycle maximum within every 15 seconds. Average output power should not exceed the rated power.
7. The power supply is considered a component which will be installed into a final equipment. The final equipment must be re-confirmed that it still meets
EMC directives.
(As available on http://www.meanwell.com)
File Name:SCP-75-SPEC 2011-05-24
 75W Single Output Switching Power Supply SCP-75 series

Mechanical Specification Case No. 901 Unit:mm

152.5

7
1

3.5
FS1
F4A/250V
TB1 2

400 3 FS2

65
F10A/250V
RED(B+) B+
L
BLACK(B-) B-

84.5
97
GND
+V =4
ORANGE(+V) 3L
BLACK(-V) TB2
1 2-M
YELLOW(L) 2
SVR1
CN2
LED
Terminal Pin No. Assignment (TB1)
Pin No. Assignment .5
ψ3
1 AC/L 4.5
2 AC/N 78
24
3 FG
159
Terminal Pin No. Assignment (TB2) 6.5 150
Pin No. Assignment
1 DC OUTPUT +V
9

9
2 DC OUTPUT -V
18.5

3-
ψ3

M3

3.5

38
.5

CN2 : JST B2B-XH or equivalent

18
L=

28.5
6
Mating Housing Terminal
JST XHP JST SXH-001T-P0.6
or equivalent or equivalent
22 117

Block Diagram
fosc : 60KHz
L

B+
RECTIFIERS POWER RECTIFIERS +V
EMI
I/P & SWITCHING &
FILTER -V
FILTER FILTER
B-

DETECTION
FG
CIRCUIT
O.L.P. CONTROL
O.V.P.

Derating Curve Output Derating VS Input Voltage

Ta=25℃
100
100
90
80
80

60 70
LOAD (%)

LOAD (%)

60
40
50
20
40

-20 0 10 20 30 40 50 60 70 (HORIZONTAL) 85 95 100 115 120 140 160 180 200 220 240 264

AMBIENT TEMPERATURE (℃) INPUT VOLTAGE (VAC) 60Hz

File Name:SCP-75-SPEC 2011-05-24

 75W Single Output Switching Power Supply SCP-75 series

Function Description
1.B+,B-
Connect the battery : B+ connected to battery positive.
B- connected to battery negative.

2.L
Output voltage detection, detect output voltage or battery voltage ( if battery is used).

Voltage of L Pin

AC OK Output voltage +0.2~0.7V(depends on Vf of diode)

AC Fail 0V

3.+V,-V
Output voltage. Can't connect the battery.

4.CN2
Temperature sensor can be connected to the unit to allow temperature compensation of the charging voltage.
If the sensor is not used, the charger still works normally.
Reference example: (Under rated DC output voltage)
Connect 100KΩ Thermistor(THINKING) on NTC. The output voltage will change along
with the temperature change. If the output voltage is adjusted other than the rated value by internal potential meter,
please consult Meanwell for suitable value of Thermistor.

Ta :0℃ Ta :25℃ Ta :50℃

SCP-75-12 14.4± 0.2V 13.8± 0.1V 13.2± 0.2V

SCP-75-24 29.3± 0.4V 27.6± 0.2V 26.4± 0.4V

29.3
27.6 (24V)
26.4
14.4
13.8 (12V)
13.2

(℃)
0 25 50
Temperature Sensor

File Name:SCP-75-SPEC 2011-05-24