JSS2 Basic Tech
JSS2 Basic Tech
JSS2 Basic Tech
OBJECTIVE
1. ___________ are basically four sided plane figure (a) Quadrilaterals (b) Polygons (c) Board
practice (d) Drawing boards
2. __________ all sides and angles are equal (a) Square (b) Rectangle (c) Trapezium (d) Kite
3. __________ are plane figures bounded by more than four straight lines . (a) Trapezium (b)
Square (c) Polygons (d) Kite
4. Pentagon has _______ Sides (a) 6 (b) 8 (c) 5 (d) 10
5. Polygon with 8 sides is Called ________ (a) Heptagon (b) pentagon (c) Octagon (d) Decagon
6. Polygon with Six Sides is Called _______ (a)Octagon (b) Hexagon (c) Decagon (d) Heptagon
7. __________ is a Straight line which touches the circumference at a Point (a) Tangent (b) Arcs
(c) Rectangle (d) Square
8. ________ is a Plane figure bounded by three straight lines (a) Rectangle (b) Triangle (c) Square
(d) Trapezium
9. _________ is a triangle that has three equal sides and three angles (a) Equilateral Triangle (b)
Isosceles Triangle (c) Scalene Triangle (d) Right angle Triangle
10. __________ can be defined as an operation organized to free from danger (a) First aid
operation (b) Rescue operation (c) Responsive operation (d) Caring operation
11. Which of the following cannot be regarded as a rescue operation (a) Vehicle-extrication
rescue operation (b) Surface water rescue operation (c) Air – Sea rescue operation (d) First aiding
12. Workshop accident includes the following except (a) Fracture (b) Bleeding (c) Wound (d)
voltaging
13. ________ is a table on which wood workers perform his operation (a) Tenon Table (b)
Imperial board (c) Dove Tail table (d) Workbench
14. Mixture of Sand, gravel, cement with water is Called (a) Plastering (b) rendering (c) Plastics (d)
Concrete
15. ________ is the name of buildings that contains many rooms on two floors (a) Duplex (b)
Bungalow (c) hut (d) High – Rise
16. Angles can be measured using ____ (a) French Curve (b) Compass (c) Protractor
17. The instrument used for drawing irregular curve is called (a) divider (b) Compass (c) Scale
French Curve (d) Rule
18. The following methods can prevent accident while working in the workshop, except (a) always
use the right tools for each job (b) Always keeps to instructor (c) Always do more than two jobs at
the same time (d) Avoid using worn out tools
19. ________ are equipment used in order to achieve safety? (a) Fire alarm (b) Fire extinguishers
(c) Safety devices (d) Fire buckets
20. Metals can be classified into _______ (a) Six (b) Five (c) two (d) Four
21. Papers are manufactured from _______(a) wood (b) Ferrous (c) alloy (d) ceramics
22. The major purpose of maintenance in engineering is to ________ (a) Keep it in good working
condition (b) Prevent from making loud noise (c) Stop it from working too long (d)Enable it to last
forever
23. Workshop accident includes the following except (a) Plastering (b) Bleeding (c) Fracture (d)
Wound
24. One of the following is not among the rescue safely measures (a) Face cap (b) Safely boot (c)
hand gloves (d) helmets
25. First – aid can be used to care for the following except (a) Headache (b) Injury (c) Accident (d)
Blood Donation
26. __________ is used for transferring measurement (a) Divider (b) punches (c) Micrometer (d)
Try square
27. _________ is drawn at the bottom right hand corner of the drawing paper (a) Boarder lines
(b) Title block (c) Lettering (d) Figures
28. _______ are poor conductors of heat and electricity (a) Plastics (b) Metal (c) Copper wire (d)
Conductors
29. ___________ Plastic can be softened into liquid form and remoulded (a) Thermosetting (b)
Ceramic (c) Thermoplastic (d) Synthetic rubber
30. Any material that allows free flow of electrons and electricity is Called _________ (a)
Conductors (b) Insulator (c) Ceramics (d) Synthetic
31. The brown material between electric poles and the electric wire is Called (a) Insulators
(ceramic) (b) Thermoplastic (c) Synthetic (d) Vulcanization
32. Glass belong to _________ family (a) Plastics (b) Synthetic rubber (c) Thermo set Plastics (d)
Ceramics.
33. Which of the following can be used for drawing vertical and inclined lines ? (a) Protectors (b)
Scale rule (c) Compass (d) Set square
34. Scale rules are used to produce (a) A good Linear drawing (b) Equal and normal size of
drawing (c) Enlarged sizes of drawing (d) Reduced or enlarged sizes
35. Which of the procedures comes first in Constructing a building (a) Excavation (b) concreting
(c) Level (d) Site preparation
36. Which of the following is not a Quadilateral (a) Prism (b) Rhomboid (c) Rhombus (d)
Parallelogram
37. __________ are used to reduce wear and tear (a) Lubricant (b) Vulcanization (c) Synthetic (d)
Abrasives
38. Oil and Grease are used as_______ (a) Vulcanization (b) Lubricants (c) Synthetics (d) abrasives
39. Polygon with (10) Ten sides is Called (a) Pentagon (b) Heptagon (c) Decagon (d) Nonagon
40. We have ____ types of technology (a) 5 (b) 4 (c) 3 (d) 2